Search Documents

By l. Bokányi, T. Varga

"The recycling of waste car tyres is a very important environmental task. The waste tyres usually are re-used or recycled by thermal processes like pyrolysis, gasification or incineration. The main problem associated with these processes is the sulphur content of waste tyres originated from the vulcanisation process, which pollutes the environment and the valuable products (i.e. pyrolysis oil) as well. In our research the desulphurisation of waste, mechanically prepared tyre sample was systematically investigated by the biosolubilisation with Acidithiobacillus thiooxidans, strain Karitas. Parallel, the experiments with sterile 9K nutrient medium were also carried out. It was found that the vulcanisation sulphur can be solubilised due to both the bio- and the chemical leaching, although the bioleaching is more effective. The solubilised vulcanisation sulphur then forms precipitates. The precipitates are forming in the bulk solution, as well as on the surface of rubber particles. The origin of the precipitates was investigated using XRD and scanning microscopy with micro probe. The origin of the precipitates is different: while in the process of the vulcanisation sulphur solubilisation with 9K medium the jarosite (KFe3+3(SO4)2(OH)6) forms, the course of the biosolubilisation with Acidithiobacillus ferrooxidans Karitas is accompanied by the formation of the jarosite and the halotrichite (FeAl2(SO4)4 · 22H2O) as well. The formation of the latter is the biomineralisation. The mechanisms of the bio- and chemical solubilisations are rather different as it was found and experimentally proved by several tests, and depends on the retention time of the solubilisation. Special efforts were done to elaborate the proper separation of the precipitates from rubber particles. Combination of intense dynamic stirring and recycling flotation process to remove the precipitates was applied for this purpose. The surface properties of synthetic jarosite were revealed using zeta-potential measurements at different pH and in presence of collectors. The parameters of the flotation were chosen based on the revealed surface properties of the precipitates. Finally, the sulphur recovery of the recycled rubber was achieved as low as <0.5%, sulphur content of it 0.17%, 12-times lower than that of the waste tyre sample after mechanical preparation."

Jan 1, 2018

By R. H. Pemberton

"THE Mattagami district of Quebec has, during the past few years, experienced intense exploration by virtually every mining company operating in Canada. As a result of this activity, a number of well-mineralized zinc-copper bearing bodies have been found, some of which will almost certainly go into production. Much of the area has undergone what is now termed ""Saturation Prospecting"" or intense and detailed geological and geophysical surveying, followed by the drilling of nearly all possible bets. Considering only the airborne geophysical surveying, some blocks of ground have been flown by virtually every geophysical instrument which has to date been installed in an aircraft. A list of these different geophysical instruments would include: l. Fluxgate-type total field magnetometers 2. Vertical field magnetometer ,3. Nuclear-precession magnetometers 4. Single-frequency out-of-phase electromagnetometers 5. Dual-frequency out-of-phase electromagnetometers 6. Horizontal component measuring electromagnetometers 7. In-phase and out-of-phase electromagnetometers8. Dip-angle measuring electromagnetometers."

Jan 1, 1961

By M. E. Holuszko

Although there is no widely accepted rigorous definition of handleability, the handling coal characteristics often referred to as handleability define whether a coal has the ability to flow unhindered through the processing and transportation systems. The handleability may be severely affected if fine coal particles tend to aggregate. In the pelletization process, the rolling action of the drum is applied to bring the individual particles into proximity with each other so that they can aggregate and form pellets. Because of apparent similarities between these two processes, the pelletization tests are carried out in parallel to the handleability tests in this project, and the pelletization results are used to explain coal handleability properties.

Jan 1, 2004

By W. M. Weigel

"Sand is one of the most useful and, fortunately, one of the most common mineral commodities. By far the largest proportion of the production is used in construction, including all forms of building, concrete and paving, sand for this purpose is produced in every State in appreciable amounts. Excluding send used for railroad ballast, molding sand stands not in tonnage produced, followed by glass sand.Special sands. In addition to the above, many grades of sands, with special characteristics, are used in industrial processes, and may be classed in a group as ""special sends"". This includes filter sand, sand blast sand, engine sand, abrasive send, fire or furnace send, special flooring sand, roofing sand used as a finish for prepared roofings and pottery placing sand sand blast and filter sand have been discussed in previous reports.Very few send companies depend upon the production of any one of these grades, as their source of revenue. They are generally especially prepared from the bank run of sand by different methods of screening or washing, or may, in some instances, be by-products from the production of ether grades. Many companies not now producing them might be able to supply local demands by a slight addition to their plant. In nearly all cases, they command a better price than the usual grades of building sand.Definitions and Properties.Engine sand, or traction sand, as it is sometimes called, is used to prevent the slipping of the driving wheels of locomotives, or other self-propelled vehicles, on wet or slippery rails. Its greatest use is, of course, for railroad locomotives, but street cars use considerable amounts and mine locomotives require its use. As the send must be very dry when used, most consumers have their can drying equipment, so it is often shipped damp, with its natural water content on what resulting from washing by the producer."

Oct 1, 1924

By Xuchen Fan, Chenyang Zhou, Yuemin Zhao, Liang Dong, Chenlong Duan

A gas–solid fluidized bed using magnetite particles is an effective methodology for coal beneficiation in the field of dry coal cleaning. Broadening the size range of magnetite used in the bed decreases medium preparation cost. In this study, a tapered fluidized bed was used to investigate a magnetite particle size range of −0.5 + 0.074 mm. The results showed that a tapered fluidized bed effectively strengthens mixing of magnetite with a wide size range (−0.5 + 0.074 mm). The results of beneficiation experiments indicated that with increasing tapered angle, separation efficiency increased and then decreased. The highest separation efficiency was obtained at a tapered angle of 10°. The optimal results showed that the ash content of the concentrate decreased from 31.82% to 12.33% with a probable error of 0.11, which indicated that a tapered fluidized bed was efficient to improve fine coal beneficiation performance.

By A E Reschke

The high-shear colloidal mixer is generally recognised as the most efficient method of mixing cement based grouts. Only recently however has this technology been applied to the production of cemented rockfill (CRF) for use in underground mines in North America. Traditionally, paddle type mixers have been used to produce the cement based slurries required for the preparation of CRF. While considerable success has been achieved with these mixers, tremendous advantages are attained with the colloidal mixer. The combined effect of the highly efficient mixing action and the ability to mix low water/solids ratios, allows for reductions in the cement content for a given strength requirement. Cement can also be replaced by cheaper fillers such as flyash, resulting in further cost savings. Although large-scale dedicated CRF hatching plants are typical, there is a growing need for mobile plants capable of operating anywhere underground. The compact size and rapid hatching speed of high-shear colloidal mixers has allowed them to be incorporated into skid mounted systems capable of producing and discharging cement based slurries onto rockfill aggregate for the production of CRF. In many cases run-of-mine development waste can be used as CRF aggregate with these slurry plants thereby reducing the cost of waste rock removal. These relatively low cost portable plants have now allowed several mines to economically rccmer isolated pillars and realise positive returns on their investment.

Jan 1, 1998

Sapporo-Iwanai district is located at the intersection of the northeast Japan arc and Kuril arc, associated with the subduction zone. This area is characterized by Miocene submarine volcanism followed by Plio-Pleistocene subaerial volcanism. &nbsp; Koryu, a small epithermal Au-Ag deposit, occurred in Pleistocene (1.4 - 0.85 Ma) within Miocene sedimentary rocks near a subaerial andesitic volcano, while Toyoha, a large epithermal Pb-Zn-Ag (-Au) deposit, also occurred near a subaerial andesitic volcano. Although most of the base metal deposits formed in middle-late Miocene, Toyoha formed in Plio-Pleistocene (2.93 - 1.60 Ma) within Miocene volcanic and sedimentary rocks. This epithermal mineralization was partly overprinted by xenothermal Cu-Sn-In(-Au) mineralization (2.68 - 0.49 Ma). &nbsp; Hydrothermal alteration differs vastly between Koryu and Toyoha: host rocks at Koryu were not intensively altered, although wall rocks adjacent to veins were silicified, while those at Toyoha show intensive and extensive neutral-pH alterations. Geological and chronological studies show that middle~late Miocene (12.5 - 8.4 Ma) alteration was pervasive and overprinted by Plio-Pleistocene (2.93 - 0.49 Ma) alteration. The base metal veins in the middle-late Miocene were not well developed, but were large in number with great depth. &nbsp; These studies show that the hydrothermal activity at Koryu is rather small and short-lived, while that at Toyoha is large, long-lived and characterized by overprinting of different hydrothermal systems. The subaerial magmatic activities yielded not only the andesite lavas, but also generated hydrothermal solutions for the formation of both Koryu and Toyoha. The metals were possibly derived from such magma. At Toyoha, the hydrothermal solutions could also remobilize metals from old ores. &nbsp; The size, life span of magmatic-hydrothermal system, and overprinting on the old mineralizing systems could constrain the type of metal deposits (precious and polymetallic deposits) nearby subaerial andesitic volcanoes in Plio-Pleistocene.

Jan 1, 2005

By Marc Lonoff

Byproducts are more important to the copper mining companies than to the copper market. Copper ores frequently contain gold, silver, molbydenum and cobalt. With the increase in the prices of these metals copper mining has become more profitable. If byproduct prices remain high, additional firms will be attracted to the copper industry; the increased supply of copper will reduce the long-run copper price. However, this is unlikely to happen because the markets for the copper byproducts, especially molybdenum and cobalt, are small. Increased recovery from copper and other sources will depress the prices of these byproducts before the copper price is significantly affected. Should byproduct prices remain high the copper market will both settle at a lower long-run price and be more unstable in the short run. Since changes in the copper price do not affect the entire earnings of a multi-metal mine, the copper price must fall further before such mines reduce output in the short run. Higher byproduct revenues will make copper supply less responsive to copper price; shifts in copper demand will result in greater copper price fluctuations in the short run than they did before.

Jan 1, 1980

By Guy A. Johnson

Despite the use of warning alarms to alert miners to the backward movement of large mining equipment, miners still are injured too frequently in backup accidents. Currently approved backup alarm technology consists of continuous sounding alarm systems. New technology has developed a warning system that initiates an alarm only if there is an object close behind the vehicle. This advancement eliminates constant exposure to the alarm because a warning is given only in case of a potential collision. Adoption of this development can improve safety and reduce damage, especially for front-end loaders (FEL&apos;s). It will also eliminate a source of nuisance noise in urban and residential areas. This Bureau of Mines report describes the general characteristics of infrared (IR) light, ultrasonic wave, and Doppler radar technology as used for backup alarms, and reviews the testing of the most promising detection devices.

Jan 1, 1986

By Ronald H. Church

As part of the Bureau of Mines health and safety research program in strata control, a ground-penetrating radar (GPR) system capable of pene-trating approximately 10 ft into the mine roof has been devised to identify anomalistic conditions. The GPR system consists of a transmitter with carrier frequencies of 250, 500, and 1,000 MHz, utilizing a dipole antenna, and a receiver, consisting of a dipole antenna fed into a sampler with a time base housed in a storage oscilloscope. A computer was utilized for data acquisition and data processing. Data analysis by computer enhancement revealed recognizable return ra-dar signatures from the middle man rock and main roof of the test site. These stratigraphic anomalies can be cataloged for recognizable fea-tures, which from the past history of the mine may have been shown to create strata control problems. Early recognition of such features could lead to immediate corrective actions and result in the saving of lives.

Jan 1, 1985

By W. K. Tolley

The U.S. Bureau of Mines (USBM) is currently investigating the electrochemistry of mineral flotation. A significant need in this area is greater reliability of sensors. The USBM is testing electrolytic methods to clean and condition redox-sensing electrodes to improve the reliability and extend the service life of these instruments in the harsh physical and chemical environment of mineral processing slurries. A novel method for removing scale from fouled electrodes has been developed that includes anodic polarization to 1.2 V versus the Ag/AgCl reference potential, followed by brief potentiodynamic conditioning. Laboratory results show that this technique removes calcarious deposits from gold sensing electrodes and returns the electrode to useful service within approximately 10 min. Mechanical abrasion to remove the scale is thereby avoided.

Jan 1, 1994

By Silas Li, Michael Harris-Gifford, Jason Choi, William H. Hansmire

Twin-bore tunnels with a single track in each tunnel are currently the most common subway tunnel configuration. However, a large diameter single-bore tunnel with two tracks separated by a center wall could replace twin-bore tunnels and introduce potential benefits but require necessary modifications to the subway system. In particular, a nominal 40-foot-diameter single-bore tunnel can be considered in lieu of nominal 20-foot-diameter twin-bore tunnels. This paper discusses the benefits and modifications introduced by replacing twin-bore tunnels with a single-bore tunnel, with respect to various elements of the subway related to the tunnel, stations, track, and tunnel systems.

Dec 1, 2022

By Ali S. Al-Watban

"In this paper, the room temperature friction and deformation properties of various polycrystalline diamonds; i.e. aggregates of diamond crystals with a ""binder"" phase of cobalt and a polycrystalline coating produced by a chemical vapour deposition processes (CVD) were studied when softer metallic and ceramic sliders were used. The experiments were conducted· at relatively low sliding speeds (10 mm/min), in a vacuum of 10-5 mbr after having cleaned the specimen surfaces by out-gassing them for about 30 min at 800 °C. As a result of increasing the number of traversals significant wear of the coated diamond by softer metallic sliders (aluminium and mild steel) was observed. With ceramic sliders, it is shown that the multiple traversals result in the formation of wear groove. With diamond silicon carbide, high friction and adhesion lead to significant metal transfer which then pre-empts cumulative deformation of the harder materials. With the diamond-cobalt composite, the friction is surprisingly low, there accumulation of wear debris on the tip of the slider but no permanent transfer of metal and the harder specimen is not damaged even after 5000 traversal.IntroductionPolycrystalline diamond is mainly produced as tool materials for the machining of hard metals and composites. Thus, the sliding friction and wear resistance are amongst the most important properties relevant to those applications.During cutting by PCD the wear mechanism is mostly influenced by the chemical affinity between the tool material and the workpiece. For example, diamond based materials are not recommended for machining ferrous materials because carbon is highly solubie in iron: This leads to the graphitisation of diamond particles and hence a high rate of diffusion wear is observed (Brookes and Lambert, 1982)."

Jan 1, 2000

By G. Belzil, F. Robichaud, M. Fullam

ABSTRACT The Goldex mining and milling complex is operated by Agnico-Eagle and is located in the Abitibi greenstone region of northwestern Quebec, Canada. Commercial production started in 2008. Average gold recovery is 93.5% with approximately 68% of gold recovery coming from the gravity circuit. During the first three years of production, three gravity audits were carried out to optimize performance of the gravity circuit. This paper presents results of the audits and the development of a model linking gravity and overall gold recovery, and outlines improvements made to increase gravity performance and reduce operating costs.

Jan 1, 2013

By M Haest

This study demonstrates the application of HyLogging™ technologies for mineralogical characterisation of different iron ore types throughout the Hamersley Province (Western Australia), including a channel iron deposit (Murchison Metals Ltd) and bedded iron deposits in the Brockman and Marra Mamba Iron Formations (BHP Billiton Ltd).Drill core from these deposits was analysed using CSIRO’s hyperspectral drill core logging systems (HyLogging systems), which are commercially available at the AMDEL and AMMTEC laboratories in Perth (Western Australia), through a leasing agreement. These HyLogging systems provide high resolution photographs at 0.1 mm pixel resolution as well as visible and infrared spectroscopic refl ectance data at 1 cm spatial resolution. The minerals identified include haematite, goethite and its subtypes (ie vitreous and ochreous goethite), AlOH-clays (kaolinite, Al-smectite and white mica), carbonates, gibbsite, chlorite, amphibole and hydrated silica as well as water content. The abundance and composition of these minerals was established from the spectral data and was validated against XRF analyses.The full potential of HyLogging systems in the iron ore industry is only starting to be unveiled, but some major benefits have already been demonstrated:• HyLogging systems can delineate different ore zones by mapping the vitreous and ochreous goethites. This has a potentially large impact in mine planning and operations, as hard, vitreous goethite and soft, powdery, ochreous goethite have different processing characteristics that can affect plant throughput if not carefully managed.• HyLogging mineralogy can also be used to support stratigraphic interpretations of the host, for example in subdividing the Dales Gorge 1 - 4 submembers of the Brockman Iron Formation.• HyLogging can have a potentially signifi cant impact on waste rock characterisation, as many of the waste materials can be identifi ed and quantifi ed with hyperspectral data (eg clay-type,• hydration state).• HyLogging can provide accurate three-dimensional (3D) mineralogy to iron ore companies that will empower them to improve future exploration and resource planning.• Application of high resolution photography to further improve ore deposit domaining is also to be considered.

Jul 11, 2011

By P Crittenden

Thiess Pty LtdÆs Australian Mining business unit used 7.6 PJ of energy in the 2007/2008 financial year. This represented more than 85 per cent of Thiess Pty LtdÆs total energy use and therefore meant that the Australian Mining business unit is required to conduct energy efficiency assessments and report publicly on the outcomes by December 2008 under the Federal GovernmentÆs Energy Efficiency Opportunities (EEO) Act. Thiess Pty Ltd has a policy commitment to sustainable development throughout its operations. This includes minimisation of its carbon footprint and the Australian Mining business unit has a strong focus on efficiency in all of its operations. It approached the energy efficiency assessment as an opportunity to further improve and build on its energy efficiency and greenhouse gas reduction focus in the business. As a mine contractor, Thiess faced a number of challenges in designing an assessment process that would be both effective and efficient to deliver. For example, unlike most other companies involved in the Energy Efficiency Opportunities program, the energy use associated with the Australian Mining business unit is not fixed to any single geographic location in Australia. Mining vehicles are moved from site to site according to the specific requirements of mine owners and the timing associated with the commencement and completion of contracts. Thiess departed from a traditional æsite by siteÆ based assessment and designed a ærepresentative assessmentÆ approach that involved detailed investigation of data across all sites and a focused assessment on a single site.Data and analysis was an essential part of the assessment and indicators at company, mine and site level were essential in identifying opportunities and tracking progress. Forty-six potential energy saving opportunities were identified and four of these are currently being implemented. The projects being implemented are: payload management, automating mobile lighting equipment, plant idle time management, and turbo idle downtime. The potential savings from the four major projects that have been identified are approximately 150 800 GJ/annum, equivalent to 10 600 tonnes of CO2-e/annum with a simple payback period of less than two years. Beyond the fuel savings however, there are a number of other benefits from the assessment, including operational efficiency, reduced maintenance costs and even a potential reduction in the number of vehicles required to complete the work. The EEO assessment has significantly increased the importance and urgency of energy efficiency and facilitated the sharing of good practice across all Thiess operations. Not only have four projects been adopted for immediate implementation but a further pipeline of projects is available for future possible implementation. This case study describes: how Thiess conducted its assessment including the use of energy data and indicators, the opportunities identified that are currently being implemented, and the lessons learnt and how other organisations can use these to improve their approach to energy efficiency assessments. This case study is a more comprehensive version of a case study developed for the Commonwealth Department of Resources, Energy and Tourism. The assessment results reported in this case study are drawn from the Thiess Energy Efficiency Opportunities Report 2008.

Jan 1, 2009

By B Maybee, L Fava, D Millar

In the context of a case study for an underground gold mine, the value generated by a schedule optimisation tool (SOT) is assessed. SOT is a software tool for underground mine planning that maximises the net present value (NPV) of a development and production schedule. A baseline study measures the NPV of a schedule generated by SOT from a sequence prepared by the site mine planners. Operational resource constraints and precedence constraints are adhered to by the schedule and NPV is evaluated with a financial model including revenues, costs and discount rate, as specified by the mine planner.The case study has several facets in addition to the baselining component. Scenarios were conducted that examined the degree of constraint on operational resources, the projected gold price and unit costs. Life-of-mine schedules subject to optimisation using SOT allowed for equitable comparisons.Haulage was identified as a dominant constraint for the mine. It was one of six operational resources that were used to constrain the optimisation of the mine schedule, with alternative levels for some of these constraints being identified so that their effects on the NPV could be studied. Alternative price projections for gold and different cost projections were identified and their effects on the optimised schedule examined. Price and cost scenarios that brought additional economic material into the schedule at various times in the mine life were considered in comparison to a scenario that assumed no additional economic material would become available.This case study illustrated that the use of a schedule optimisation tool to optimise mine schedules provides mine planners with an ability to perform a wide variety of analyses in a relatively short period of time. Such tools thereby support strategic decision-making that can add significant value to an orebody.The case study demonstrates that by fixing the set of development and production activities to be carried out before optimising the life-of-mine schedule, the mine planners can inadvertently set up a situation where the NPV would be progressively eroded in the last several years of the mine life. This clearly illustrates the need for schedule optimisation to be integrated with life-of-mine planning.CITATION:Fava, L, Maybee, B and Millar, D, 2012. Decision support for an underground gold mining operation - A case study using the schedule optimisation tool, in Proceedings Project Evaluation 2012 , pp 41-48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By B. J. Jody

This paper describes a one-step thennal-treatment process, developed at Argonne National Laboratory, to remove all organic contaminants from the glass-fiber waste that is generated during the glass-fonning process. The recovcred glass fibers can then be recycled into new glass fibers or new glass products without adversely impacting the operations of the glass industry or the quality of its products. Our process involves shredding the waste to a manageable size and then processing it at temperatures below its melting point to remove the polymeric-coating layer. The glass industry generates more than 60,000 tons of glass-manufacturing waste annually in the glass-forming process alone. Recycling of this waste stream can keep this non-biodegradable waste out of the landfills. In addition, use of recycled glass lowers energy costs, by an average of about $5 per ton as compared to using virgin raw materials to make virgin glass fibers. This process will also reduce the emission of C02 by 17,400 tons a year and it will also reduce the emission of nitrogen oxides. Economic analysis of our process shows a potential payback of less than 2 years.

Jan 1, 2003

By K. G. Davies, M. J. Royea

"A major program of pillar recovery at the Sullivan mine has been assisted for the past several years by a concerted series of rock mechanics investigations. The object of these investigations is to measure the parameters of rock behaviour which influence pillar mining. This quantitative information is then used in the design of mining methods appropriate for various conditions.Instrumentation to measure absolute rock stress, changes in rock stress and the gross deformation of rock masses has been developed. Various instruments are described, as are instrument evaluation procedures and typical test results. The data from underground measurement projects have been used to modify pillar extraction sequences along re-treat fronts. Rock mechanics information from individual pillars has been incorporated into the design of mining methods to suit particular circumstances."

Jan 1, 1968

By Paul B. Valenti

The Nevada Moly Operation of Anaconda Minerals Co., (a molybdenum/copper ore body) was initiated in 1978, with a contract to Bechtel Civil and Minerals Inc. for construction of a mining and milling facility near Tonopah, NV. Ground was broken on the concentrator portion of the project in August 1979$ with a multi-phased startup of the mill beginning in June 1981. Processing design tonnage of 20 000 t/d (22,000 STPD) was reached in early 1982. Major pitfalls of rapid design and implementation of engineering, construction, and startup are considered. The operation of the concentrator including SAG milling, ball milling, bulk rougher flotation, copper/moly separation, moly regrinding and cleaning, thickening, and product loadout are discussed.

Jan 1, 1983