Search Documents

By Benjamin Cebrián, María Gil, David Flores

In many occasions during the Mining operation life, blasting engineers find different and controversial results of fragmentation, dilution or wall control for the same geotechnical domain and blast design (pattern and explosive charge). Most of the times, the difference between same blast designs is not measured, not controlled. Once a blast designed is defined, the most important part of the process after that is the implementation of every step of the blast on site. Almost nobody is measuring it, controlling it, but just controlling implementation is possible to relate blast design with results in a consistent way, to optimize the full process of D&B. Controlling implementation not only per event but also to check and change trends and decision-making is paramount for optimization and saving millions of extra costs every year. The lack of resources and the hardness to manage all the info created every day in a blast make this process very tough and difficult to maintain in long term. The use of new technologies on site and software that allows a best, more consistent and continuous control of blast implementation have been proved to be the key for optimizations and cost saving. This document shows the evolution of drilling and blast digitization process, savings and trends in a mine, using new technologies that creates business opportunities and general improvement of D&B process.

By Zhitong Sui

Based on several case studies on the precipitating behavior of valuable nonferrous metal compounds (VNMC) in molten slags a green technology for the recovery of VNMC from molten slags was proposed. This technology involves three steps: (I) The selective enrichment of the dispersed VNMC into the designed mineral phase in the molten slag; (2) The selective coarsening of the designed mineral phase to a critical grain size in the molten slag; (3) The selective separation from tailing of the grown mineral phase in the solidified slag by dressing or hydrometallurgy processes. This is a clean and low cost technique and has a great capacity to deal with a large quantity of slags. The utilization of the recovered VNMC such as Titanium, Boron, Vanadium compounds was summarized as examples of application. It was confirmed by experiments that the precipitating behavior of the designed mineral phases like Perovskite(CaTiO3), Suanite(2MgO*B2O3) and Sincosite(CaOoV2O5*P2O5) in molten slags is obviously affected by operation factors such as temperature, chemical composition, heat-treatment, additives and so on. The precipitating kinetics and mechanism of the VNMC from molten slags during solidification processes were also investigated.

Jan 1, 2003

By T. H. Eyde

Several hundred natural zeolite deposits occur in Tertiary and Cretaceous age formations of the western United States. Most of the large deposits are altered vitroclastic tuffs. Many of these deposits consist of a matrix of a high purity zeolite mineral or minerals in which fragments of unaltered rock are imbedded. These deposits represent an extensive resource of zeolite minerals which can be beneficiated to a consistently uniform, high quality product. The beneficiated natural zeolite products will possess many advantages over the selectively mined, unbeneficiated natural products currently being produced. These advantages will include: uniform particle size, high purity, consistent quality, high brightness, low iron content, high attrition resistence, uniform cation exchange and adsorption capacities, and low price.

Jan 1, 1981

By E. Uzun

"In this study, H2SO4 and HCl leaching behaviour of an ore sample containing 1.87% of Ni, obtained from the Karaçam (Eskisehir-Turkey) lateritic deposit that started operation recently was investigated. Acid concentration, temperature and reaction time were investigated as variables by comparative leaching tests and the optimum leaching conditions were selected on teh basis of Ni, Fe, Co and Mg behaviour. For H2SO4 leaching, optimum leach parameters were 95°C, a 12 normal H2SO4 concentration and 90 minutes of reaction time, and under these conditions Ni and Fe dissolutions were 97.6% and 95.4% respectively. On the other hand, 70°C, an 8 normal HCl concentration and a reaction time of 90 minutes were found to be the optimum parameters for HCl leaching, and Ni and Fe dissolutions found were 97.1% and 97.8%, respectively.INTRODUCTION Today, nickel and various nickel compounds are obtained from sulphide and lateritic nickel ores (Moskalyk & Alfantazi, 2002). Even though about 72% of the world's nickel reserves constitute lateritic ores, only about 42% of nickel is produced from these ores. The decrease in production from sulphide deposits, on the other hand, and increases in the use of nickel in the iron and steel, and battery production sectors, and especially the production of nickel cast irons in recent years, have accelerated the importance of making use of lateritic deposits (Luo et. al., 2010; Chang et. al., 2010). In the beneficiation of sulphide nickel ores, mostly pyrometallurgical methods are used. On the other hand, about 39% of lateritic ores are beneficiated by pyrometallurgical, and 61% are beneficiated by hydrometallurgical methods (USGS, 2009). In laterite beneficiation, the ore properties are of significance; that is to say, limonitic ores are eneficiated by high pressure acid leaching or via the Caron process, nontronitic ores are beneficiated by high pressure acid leaching or heat treatment (smelting), and ores containing serpentine by pyrometallurgical methods (Berezowsky, 2004; McDonald & Whittington, 2008a; Dreisinger et. al., 2015)."

Jan 1, 2017

By Akerkar D. D, Dey M. L, Mathur S. B, Chowdhury S. K R

The extraction of gold and silver from chalcopyrite concentrates has been investigated. In view of the recent interest in non-cyanide leachants for gold and silver, one such alternative reagent, namely thiourea, has been employed in the present work. Precious metal leaching was attempted from received copper concentrates as well as pre-oxidised concentrates. Pre-oxidation of the concentrates was carried out by three different methods, namely roasting, pressure oxidation and biological oxidation. After pre-oxidation and leaching of the base metals, the leach residues were subjected to further leaching for precious metal extraction. The results obtained on the extraction of gold and silver from received concentrates as well as pre-oxidised concentrates are presented and the effectiveness of the three pre-oxidation routes employed is compared.

Jan 1, 1992

By C. -S. Xie, J. -H. Kong

The microstructure and mechanical properties of X80 hot-rolled thick steel strips with a thickness of 17.5mm produced in Wuhan Iron & Steel Company (WISCO) are introduced in the paper. The steel strips as fabricated through proper thermomechanical processing (TMP)/ on-line accelerated cooling (OLAC) processing have shown high strength and toughness, low brittle transition temperature, good weldability, and high Shear Area (SA) percentage in Drop Weight Tear Test (DWTT). The microstructure of the steel strips is characterized with mainly acicular ferrite, and fine dispersed Martensitc-Austenite (M-A) phases. It is determined that the mechanical properties are improved due to the presence of the fine M-A phases and precipitates, which could be formed by reducing the finish rolling and coiling temperatures.

Jan 1, 2005

By A. Cabañas

"In this paper, geostatistical techniques are applied to forecast the annual copper price in the short and medium terms (from one to five years ahead). These techniques allow the incorporation of monthly and multivariate information in the analysis and provide more accurate results than traditional approaches, especially as far as the one-year forecast is concerned.A second advantage of geostatistics stems from its ability to assess the uncertainty associated with the unknown future prices, thanks to estimation variances or confidence intervals, depending on the technique used. Such an assessment has a crucial importance in decision-making, from both macroeconomic and microeconomic points of view. IntroductionThe copper price traded in the London Metal Exchange is a relevant parameter for defining macroeconomic policies of producing countries like Chile. It is also a key factor for the mining companies, since fluctuations in the sell price affect the expected financial flows. Due to the amount of money involved in decision-making, it is necessary to have accurate forecasts of the future copper prices and to quantify the uncertainty associated with such prices.This paper focuses on the annual copper price estimation in the short and medium terms, i.e., from one to five years into the future. Henceforth, the word “estimation” will be used as a synonym of “forecast,” according to the geostatistical jargon (Matheron, 1989).Two main approaches, based either on statistics or econometrics, are currently used to forecast commodity prices, but both of them are not very accurate when applied to copper. First, the main methods are briefly reviewed, then the geostatistical formalism will be presented. So far, the latter approach hardly has been used to estimate commodity prices, although it may reconcile both statistics and econometrics via (1) the use of a stochastic approach and (2) the handling of ancillary variables related to the copper market. Another advantage of geostatistical techniques is the ability not only to forecast the copper price, but also to measure the uncertainty associated with it."

Jan 1, 2004

By M. Abdellatif

The production of a 40% Al-Ti alloy was successfully proven at the lab scale, using pure TiO2, aluminium, and lime. These tests were conducted in an induction furnace maintained at 1600?16250C. The introduction of rutile into the feed recipe resulted in an alloy containing between 0.35 and 1.10% Zr, depending on rutile to TiO2 ratio. DC arc production of the alloy was largely accomplished at 40 and then 200kW scale. These tests evaluated various metallurgical and operational factors including target slag composition, Ti-content in the alloy, co-feeding versus sequential, furnace bath depth, and rutile as part of the Ti containing feedstock. Overall, an alloy containing 24?33% Ti was consistently produced with co-feeding of the reactants and with lower taphole tapping. When rutile was added, the zirconium analysis in the alloy remained below 0.2%. The main impurity elements were iron, silicon, carbon, nitrogen, and oxygen.

Jan 1, 2009

By Alastair Torrance, Gary Cavanough

Over the past two years a research project has been performed on reactive and hot ground. A key finding is that host materials including carbonates and coal are inhibitors to the reaction of sulphide and nitrates. The mechanism of this inhibition is pH buffering and isolating the surface of sulphide from reactants. It has been identified that acidity is a key driver of the reaction with a pH of 2 required for a reactivity event. A series of decomposition experiments confirmed that reactive and hot ground are essentially the same phenomenon with the heating produced either by the reaction of sulphide with nitrates or an external heat source. The results indicate that the key driver of detonation in reactive ground is energy and heat released from the acid induced reaction of sulphide and nitrate with no indications of sulphide being a catalyst or contributor to detonation apart from being a heat source. There must be sufficient sulphide and thermal insulation to provide and retain enough heat for detonation to occur. A pathway to detonation is postulated whereby the heat travels upwards and results in evaporation of water in the explosive. When the temperature reaches approximately 200°C (400°F) the ammonium nitrate starts to decompose, decreasing the mass of the reacting species. The material in the top layers has reduced density and specific heat hence the temperature of the top region rapidly increases up to >1000°C (1800°F) and may initiate detonation. Field tests on loaded blast holes support this proposed mechanism. Case studies are presented whereby the research findings are used to provide an analysis of historical reactive ground events.

Jan 21, 2025

By K Banerjee, C Dube

Veolia Water Technologies was contracted by a global coal mining company to design a retrofit acid mine drainage treatment facility using DenseSludge™ technology on a former coal refuse disposal site. The project constraint was to reuse current facilities in order to reduce additional capital work cost and avoid additional footprint requirements while improving treatment performance and reducing sludge production and chemical consumption. The initial installation of 454 m3/h served as a pilot plant to demonstrate the benefits of the process and ultimately provided design criteria for the new facility. The pilot demonstrated the benefit of the technology by reducing sludge volume by 90 per cent compared to conventional processes currently in use. The sludge that is reinjected into the mine contains less water, which reduces the volume of water that returns to the mine pool for treatment and mine water balance. Furthermore, the pilot plant reduced lime usage compared to conventional processes by operating at a lower pH set point, demonstrating steady pH control and stoichiometric lime utilisation.CITATION:Dube, C and Banerjee, K, 2015. Sludge conditioning technology to reduce sludge and the cost of acid mine drainage treatment, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 105–110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By J. P. Ducarme, J. L. Carr, C. C. Jobes

"An average of 1.2 fatalities occur per year in underground coal mines in the United States when a miner is struck or pinned by a remote-controlled continuous mining machine. Proximity detection technology provides a means to prevent these types of accidents by disabling all machine motion when a miner is in close proximity. Researchers at the National Institute for Occupational Safety and Health (NIOSH) have developed the intelligent Proximity Detection (iPD) system, which continuously tracks the position of miners near the machine and disables only those machine motions that could cause a pinning accident. This system, previously demonstrated using non-permissible proximity detection hardware, has now been shown to be effective when implemented using an MSHA-approved system as a platform. Performance tests have shown accuracy, repeatability, and stop zone identification to be comparable to or better than the system demonstrated with non-permissible hardware. INTRODUCTION Underground coal mining room-and-pillar operations typically use Continuous Mining Machines (CMMs), such as the one shown in Figure 1. When CMMs first became available, they were operated from an on-board operator’s compartment that protected operators from roof falls and other hazards but severely restricted visibility and subjected them to machine vibration and high levels of dust and noise. To solve these problems, remote controls were developed to operate CMMs. Now CMM operators are free to position themselves for best visibility of each mining task and are no longer subjected to the rough motion of the CMM during mining operations or the dust and noise generated by the machine. However, this technological advance removed operators from the protection afforded by the operator’s compartment and exposed them to the hazard of being struck or pinned by the CMM or other large moving machines."

Jan 1, 2015

By Nestor Cezar Heck

Aim of the present work is to continue the theoretical evaluation of the slags of the fundamental system CaO-SiO2-CrOx-MgO (Ca-O-Cr-Si-Mg quinary system) at the temperature of 1,873 [K], with the help of a computational thermodynamic tool. Driving force for this and the previous research works is the understanding of chromium losses from the molten bath into the slag. Especially motivating is the presence of solid phases in the slag, since they may prevent refractory degradation and help in the production of foaming slags. Nevertheless, Cr-bearing solid phases can lead to Cr losses, being therefore detrimental. Determination of the states of thermodynamic equilibrium for this system using a slag with fixed composition as a start material were made using MgO amount as variable. Results show the impact of the MgO content on the equilibrium phases (molten metal, liquid slag, solids) and their composition for this system.

Jul 30, 2018

By J. F. Harkom

Introduction The importance of the preservative treatment of mine timbers need scarcely be stressed here. Increasing the life of mine timbers will reduce one of the major costs of mining and also conserve the available timber supply which lies within easy access of the mines. When treated, several species of timber may be used which otherwise could not be considered, owing to their short life. Another feature which should appeal to the mining industry is that wood preservatives are a mine product, and the benefit to be derived from the increased consumption of wood preservatives due to the example set by mine owners is not inconsiderable. Mine timbers may be divided into three classes when considering preservative treatments. (1) Timber obviously not profitable to treat owing to long natural life or short period of time in service. (2) Timber that obviously should receive protection from decay. (3) Timber installed in locations where the length of service required will depend on future developments, so that preservative treatments might or might not prove to be a profitable investment.

Jan 1, 1930

By Augusto Viana Leandro Teixeira

Rare Earth Elements (REE) are fundamental for modern life products and green technologies. Supply constraints and the price peak of 2011 boosted intensive research for alternatives for processing and separation. Complex monazite- type, rare earth ores usually contain high acid consumption impurities, such as iron and aluminum, and radioactive thorium in their composition. These impurities are not removed by conventional concentration processes due to fine, micro-level association between the REE carrying minerals and the gangue minerals. This work presents a selective process route for REE extraction from iron-rich, monazite ores. The process involves sulfation by addition of concentrated sulfuric acid and pyrohydrolysis at temperatures of approximately 700–750 °C. Experimental results show REE extraction higher than 70% and low iron (below 5%) and thorium extraction (below 10%). A method based on thermogravimetric analyses was shown to be adequate to predict the behavior of a given ore sample in the sulfationselective pyrolysis-leaching process.

By Waraporn Piyawit

Grinding sludge from the sintered neodymium-iron-boron (NdFeB) magnets production process was enriched with critical rare earth elements (neodymium, dysprosium and praseodymium), which can be up to 30% in the magnets. The demand of NdFeB magnets are simultaneously growing. Therefore, rare earths recovered from waste residue would reduce the demand of rare earth elements from primary sources. In this study, the feasibility of recycling rare earths through a hydrometallurgical process was investigated. The selective leaching of Nd from grinding sludge can successfully raise the rare earths concentration to 70%. The necessity of an oxidation pretreatment to improve the selectivity between Nd and Fe will be described.

By Thenepalli Thriveni, Seong-Young Nam, Nam-Il Um, Joobeom Seo

In the present work, we report a novel microstructure of synthesized scalenohedral PCC (precipitated calcium carbonate) without any additives by a simple and ecofriendly carbonation process carried out in a liquid-gas system on the crystal growth of the scalenohedral calcite phase. Especially, the process parameters of Ca(OH)2 concentration and CO2 flow rates were investigated to enhance the sensitivity of the process. The highest average length of the scalenohedral calcite was obtained at pH 6.0, temperature 450C, Ca(OH)2 concentration 0.2M, CO2 flow rate 80mL/min, and total volume 1L. The utilization of flue gas-derived CO2 from coal fired power plants could be a form of carbon capture and storage using carbonation reaction with scalenohedral PCC. Finally, the synthesized scalenohedral PCC was used as a filer for ONP recycling. We demonstrated all these experiemnts at semi pilot plant scale.

Jan 1, 2014

By Masakazu Niinae, Tasuma Suzuki, Mai Moribe, Yohhei Okabe

Bench-scale electrokinetic experiments were performed to elucidate the electrokinetic remediation mechanisms of arsenate from artificially contaminated kaolinite. The electrokinetic experiments in which a constant voltage was applied demonstrated that high soil pH favored arsenate remediation with respect to both the remediation time and electricity consumption. It was also demonstrated that applying a pulse voltage (1 hour ON, 1 hour OFF) significantly improved the electricity consumption efficiency when the soil pH was maintained at the initial value during the experiments; this trend was not observed when the soil pH was gradually increased from the cathode side. These electrokinetic experimental results indicate that the remediation rate-limiting step varied with soil pH. When the soil pH was maintained at the initial value of 7.2 during the experiments, arsenate desorption was the remediation rate-limiting step rather than the migration of dissolved arsenate toward the anode. Conversely, when the cathode pH was not controlled and the soil pH was correspondingly increased gradually from the cathode side, the migration of hydroxyl and desorbed arsenate ions toward the anode played a more important role in the control of the overall remediation efficiency.

Jan 1, 2014

By Petrus Christiaan Pistorius, Farzin Fatollahi-Fard

The production of titanium oxycarbide – a consumable anode material used in molten-salt processes for electrowinning titanium – from heavy mineral concentrate, such as a high-titania leucoxene and natural rutile is described. The oxycarbide is prepared by carbothermic reduction of the oxide at elevated temperature. Particle size distribution (of the titanium oxide raw material) and temperature have large effects on the kinetics of the reaction, which seem to follow a “shrinking-core” model. It is anticipated that low porosity (in the anode pellets) would be advantageous during electrolysis. Particle size distribution, extent of reaction during carbothermic reduction, and sintering temperature are expected to affect pellet porosity after sintering, and are being tested experimentally.

Jan 1, 2015

By Filippo Mira-Cattò, Andrea M. R. Pettinaroli, Elena Rovetto

"The construction of Powisle station of Metro Warsaw Line 2, in Poland, required the execution of two shafts next to an urban road tunnel adjacent to the Vistula River. The shafts were linked by three conventionally mined tunnels to be excavated 10 m below the water table level, into an upper sandy and sandy silty layer and a lower stiff clayey stratum. After a failed dig attempt under the protection of jet grouting and forepoling, it was decided to deal with the tunnels excavation problem by using the ground freezing technique as a temporary, non-polluting geotechnical treatment, keeping in service the upper road tunnel. The planning of the activities and the executive phases had a significant importance for the success of the work. For work scheduling reasons the mixed system was adopted, i.e. using both the liquid nitrogen system and the brine freezing method. The freezing process management, with a real time evaluation of the soil temperature measured by thermometric strings and an accurate monitoring of the overlying road tunnel structure, allowed the tunnel excavation and lining stages to be performed under difficult conditions, without water leaking from the frozen ground shell, within the expected times and saving extra costs.INTRODUCTIONThe new Underground Line 2 in Warsaw connects the eastern and western part of the town. One of the most critical interferences was the under passing of the Vistula river and of the Wislostrada motorway tunnel, a very congested motorway along the western bank of the river, with the construction of the new station Powisle. The construction of the station required the excavation of two shafts, using the top-down system with the creation of intermediate slabs while deepening the excavation.The shafts were used for the extraction of four Tunnel Boring Machines (TBMs), two approaching from the Vistula river side (east-side) and two approaching from downtown (west-side); in order to connect the two shafts was foreseen the realization of three tunnels, two for the underground lines and the central one for the exchanging passenger platform. These tunnels were underpassing the “Wislostrada Road Tunnel” and interfered with this tunnel foundation, which consisted of diaphragm walls (DW), the “barrettes” (Figure 1).Due to the variable geological conditions at the site, the first excavation stage, with a temporary underground support constructed of horizontal jet grouting columns and forepoling, caused the North tunnel face failure, that required an immediate filling of the empty cavities with lean mix concrete under the Wislostrada tunnel slabs. Thereafter, the recovering attempt with the grout injections could not be completed because of the development of heaves induced on the tunnel structures (Bringiotti et al. 2016). In those conditions the tunnel excavation with traditional technologies appeared to be very problematic, with high risk for the structural safety of the Wislostrada tunnel. This would have meant longer duration for the works and higher costs for the General Contractor as well as for the city Council."

Jan 1, 2015

By H Zhang, S Li, J Song, Z Lv

In this paper, a method for extracting and refining metallic molybdenum using low-temperature ZnCl2- NaCl-KCl molten salt was proposed. The electrochemical behaviour of molybdenum ions in ZnCl2- NaCl-KCl molten salt was investigated in detail, and pure metallic molybdenum was collected on the cathode. The reduction and diffusion processes of Mo(V) ions in ZnCl2-NaCl-KCl molten salt were determined through a series of electrochemical methods. The diffusion coefficients and nucleation modes of Mo(V) ions were also studied, and electrolysis was conducted for a prolonged period at a constant current density. The results indicated that the electrode reduction of Mo(V) ions in ZnCl2- NaCl-KCl molten salt proceeds through a three-step reaction: Mo(V) → Mo(IV) → Mo(III) → Mo at 250°C. The Mo(V) → Mo(IV) reaction was reversible and diffusion-controlled, with a Mo(V) diffusion coefficient of 6.02 × 10-6 cm2 s-1. Additionally, the nucleation mode of Mo(V) ions was instantaneous nucleation. The products electro-deposited were confirmed of metallic molybdenum with a particle size of less than 1 μm.

Aug 21, 2024