Search Documents

By Geoffrey Brooks, Mehedi Bin Mohammad, M. Akbar Rhamdhani

Molten alkali nitrates are used commercially as thermal storage fluids (HTF) for solar thermal electricity generation. Their range of operation is limited by the thermal stability and this limits the energy (steam-Rankine cycle) efficiency of these processes. In this study, the effect of atmosphere on the thermal stability of nitrates was investigated using simultaneous thermal analysis techniques (STA). The use of oxygen (O2) as a blanket gas was found to delay the decomposition point of the ternary NaNO3–KNO3–LiNO3 (13.23–57.14–29.63 weight ratio) mixture by 55 °C. By which operating range will increase 65 °C more compared to the binary solar salt. Higher heating rates increased the decomposition point but had less effect on premelting and melting properties. Nitrogen monoxide, and O2 evolution after melting indicates concurrent reversible reactions. Similar phenomena were observed for single and binary nitrates. The eutectic melting point of ternary nitrate obtained from the STA agreed well with FactSage eutectic composition prediction.

Mar 1, 2017

By S. J. Page

The personal dust monitor (PDM) is a combined tapered element oscillating microbalance (TEOM) respirable dust monitor and cap lamp, configured to have dimensions and weight similar to those of a lead-acid miner’s cap lamp battery. The Higgins-Dewell (HD) cyclone design operated at 2.2 L min-1 airflow has previously been reported to have low bias relative to the International Organization for Standardization (ISO) convention. Previous reports have described the PDM as meeting the NIOSH Accuracy Criterion. In order to avoid certain analysis anomalies encountered during these evaluations, a different method of establishing the PDM relative standard deviation was employed. Re-analysis of laboratory data for both the early prototype and precommercial PDMs indicates that the PDM still meets the NIOSH accuracy criterion, and that the precommercial PDMs are more accurate than previously reported.

Jan 1, 2011

By A. L. Mowry, John T. Norton

Isothermal sections of the pseudo-ternary carbide systems TiC-VC-ZrC, TaC-VC-ZrC, and NbC-VC-ZrC have been examined. The sections contain an inverted U shaped two-phase field whose maximum extent is 77 molecular pct for Tic, 64 pct for TaC, and 51 pct for NbC. lsoparametric lines were determined which show the curvature of the single-phase field and the direction of tie lines in the two-phase field. It was not possible to show any relationship between atom size and the extent of the two-phase field. REVIOUS work' on the solubility relationship of several pairs of refractory cubic monocarbides from the group Tic, ZrC, VC, NbC, and TaC has shown that, with the exception of the system VC-ZrC, they all form continuous series of solid solutions. It was demonstrated that the limited solubility in the case of VC-ZrC system was primarily a question of the size factor, the size difference between vanadium and zirconium being greater than the limiting value of about 15 pet. It is interesting to consider the results of combining these isomorphous carbides in groups of three and to determine the isothermal section of the pseudo-ternary diagram at, for instance, 2000°C, a temperature that will assure an equilibrium structure in a reasonable length of time. In the ternary systems where the three pairs form complete solid solution series, it is probable that the isothermal ternary section would be a single- phase field, although this is not necessarily the case. However, if one pair of carbides has a very limited solubility, then there must be a two-phase field of some extent, and it is the purpose of the present work to examine the extension of this field and to determine if it can be related to the nature of the third carbide. This condition is fulfilled if the VC-ZrC pair, which has only limited solubility, is combined with Tic, TaC, or NbC. The relative sizes of the metal atoms undoubtedly play a role in the extent of the single-phase field, and the values obtained from the pure carbides, assuming close-packing between metal and carbon atoms and a carbon atom diameter of 1.54A, are

Jan 1, 1952

By M. J. Marinigh

Increased safety requirements, higher operational costs, greater environmental restrictions, and new competitive processing techniques are the challenges smelter operators must confront in order to remain economically viable. In converting furnaces which have tuyeres such as the Noranda Reactor and the Teniente, Peirce Smith and Hoboken converters, efficient tuyere line management is critical to optimizing blowing rates, increasing refractory life, and improving safety. This paper will describe recent improvements made to equipment used for tuyere punching, tuyere silencing, tuyere pyrometry and refractory drilling of tuyeres and how the proper application of the equipment can lead to operational and safety improvements.

Jan 1, 2007

By G. Minhas, M. Pule, Y. Laffitte, M. c. McGurn, T. Tzanetakis, Peacey. J., R. Susilo

Titanium (Ti) metal production from titanium tetrachloride (TiCl4) using magnesium (Mg) as a reducing agent is the well-known Kroll process. A chloride route is used to avoid oxidation of the titanium sponge. The sponge is consolidated into ingots and can then be made into powder by melting and atomizing or by hydriding/dehydriding. Attempts at direct powder production have met with difficulties, including low Ti yield and the formation of very fine particles (particles between 25-100 µm are desired). This paper discusses two methods to produce Ti powder in a molten salt medium using magnesium powder as a starting material instead of a pool of molten magnesium. The first method is a direct reduction of gaseous TiCl4 injected in the melt with the magnesium powder in suspension in the molten salt. The second method is a two stage TiCl4 reduction reaction where recycled Ti was used to form titanium dichloride (TiCl2) in the first stage followed by addition of magnesium powder into molten salt in the second stage. A correlation between Ti yield and processing variables such as TiCl4 to Mg ratio, Mg particle size, TiCl2 concentration in the melt, and reaction temperature was studied. The Ti powder formed was also analyzed for particle size distribution. Despite challenges and difficulties encountered, this paper shows some promising results which could provide guidance to others working on direct Ti powder production.

Jan 1, 2015

By J. C. Zelanko

The U. S. Bureau of Mines conducted a multi-faceted geomechanics research project at a bump-prone longwall coal mine in eastern Kentucky. This mine presented a unique opportunity to study coal mine bumps in that the problem appeared to be confined to areas beneath a sandstone channel of limited areal extent. The Bureau's research plan sought to exploit the uniqueness of the site by monitoring strata behavior and longwall support reactions as the longwall face approached and passed beneath a sandstone channel. The study incorporated static pillar stress and strata deformation measurements, shield support leg pressure measurements, and microseismic monitoring as well as geologic mapping and the collection of observational data. Data collection was underway when a major coal bump occurred on the longwall face at the mine. Pillar behavior (load and deformation), shield loading, and microseismic activity were monitored prior to, during, and after the bump. Observations in the tailgate indicated that these pillars were failing prior to and after the face bump. Shield load data which were evaluated in an effort to identify trends which could be used to forecast coal bumps appear to provide a measure of the effectiveness of destressing operations conducted on the face (e.g. shot firing). Analyses of microseismic data revealed anomalous values associated with microseismic "energy" prior to the face bump. In addition, microseismic source location data and underground observations provided some insight as to the sequence of pillar and face bumps.

Jan 1, 1991

By Ma Ying

The continuous directional solidification technique of five kinds of special ZA alloys with eutectic, peritectic and eutectoid transformation under the condition of continuous casting by heated mold was studied. The mechanism of surface defects appearing in ZA alloy line was discussed and the structure of some defects were analyzed by SEM. The results show that only when the fitting of various technique factors, pressure head, outlet temperature, pulling speed and cooling condition are reasonable under a certain range, can the ZA alloy smooth line be continuously pulled out. Unreasonable techniques will result in hot tear, rough surface, mush outlet, leaking and other defects. The shape and location of solid-liquid zone have an important influence on the formation of the above defects. When the solid-liquid zone is located in the mould outlet or inner mould, the surface of solidification will protrude into the inner mould. If the remaining liquid cannot counteract the solidification contraction, a rough surface will appear. If the solidification surface further into the mould, the ingot in the mould will have a great friction force when pulling and will form a hot tear. When the solid-liquid zone is moved out of mould, the solidification surface will turn into a plane, which easily results in leaking. A vibration or unstable operation will cause an ingot winding during pulling

Jan 1, 2003

By Yichi Lu, Haydn N. G. Wadley, Douglas T. Queheillalt

"Using a 3-D ray tracing methodology combined with laser ultrasonically measured elastic constant data near the melting point, ultrasonic propagation in cylindrical single crystal bodies containing either a convex or a concave solid-liquid interface have been simulated and used to design new sensing concepts. Ray paths, wavefronts and time-of-flight (TOF) of rays that travel from a source to an arbitrarily positioned receiver have been calculated. Experimentally measured TOF data have been collected using laser generated/detected ultrasound on model systems with independently known interface shapes. Both numerically simulated data and experimental results have shown that the solidification (interfacial) region can be identified from ultrasonic transmission TOF data. Since convex and concave solid-liquid interfaces result in distinctively different TOF data. When TOF data collected in the diametral plane are used in a nonlinear least squares algorithm, the interface curvature has been successfully reconstructed and ultrasonic velocities of both the solid and liquid obtained. The reconstruction errors were found to be less than 5%.IntroductionMany of today's single crystal semiconductors are grown by variants of a vertical Bridgman technique in which a cylindrical ampoule of a molten semiconductor is translated through a thermal gradient, resulting in directional solidification and the growth of a single crystal, Fig. 1.1 It has long been recognized that during crystal growth the velocity and the shape of the solid-liquid interface, together with the local temperature gradient, control the mechanism of solidification (i.e. planar, cellular or dendritic), the likelihood of secondary grain nucleation/ twin formation (i.e. the loss of single crystallinity), solute (dopant) segregation, dislocation generation, etc. They thus determine the crystals' resulting quality.2-4 The solidification rate and the solid-liquid interface shape are also sensitive functions of the internal temperature gradient (both axial and radial) during solidification.5•6 This in turn is governed by the heat flux distribution incident upon the ampoule, the latent heat release at the interface, and heat transport (by a combination of conduction, buoyancy and surface tension driven convection, and radiation) within the ampoule. The solid-liquid interface's instantaneous position, velocity and shape during crystal growth are therefore difficult to predict and uncontrolled during growth, especially for those semiconductor materials with low thermal conductivity (e.g. CdTe).4-6 The development of technologies to non-invasively sense the interface position and shape throughout the vertical Bridgman crystal growth process has therefore become a key step toward developing a better understanding of the growth process, for enabling sensor-based process control, and thus ultimately for improving the yield and quality of difficult to grow semiconductor materials like CdTe."

Jan 1, 1997

By T. C. Maswanganyi, G. L. Smith, R. C. A. Minnitt

This paper identifies the strategic gaps and opportunities for the South African mining industry’s contribution towards advancing sustainable development. Mineral resources companies are confronted by a range of complex social performance challenges, which largely manifest in sporadic community and labour unrest, undermining the sustainability and profitability of these companies. Integrating supply chain management, strategic long-term planning and sustainability planning is identified as a strategic gap that can contribute towards the sustainability of mining companies, if effectively implemented. Contributing towards sustainable development by the South African mining industry is not merely a voluntary requirement on the industry but a legal requirement in terms of the Minerals and Petroleum Resources Development Act No. 28 of 2002. This Act is legislation aimed at advancing socioeconomic development in communities that host mining operations and in areas that provide labour to the South African mining industry. In contributing towards the advancement of sustainable development in mining host communities, not only will mining companies fulfil a legal requirement in terms of the Minerals and Petroleum Resources Development Act, but they will also prevent negative social and economic impacts in those communities. This paper identifies innovative and cost-effective ways of advancing sustainable development by integrating strategic supply chain management, strategic long-term planning, and sustainability planning.

Dec 15, 2025

By Walter C. Lorenz

In connection with its renewed study seeking solutions to problems created by release of acid water from bituminous coal mines, the Bureau of Mines recently surveyed reports already written on the subject. This publication is based on that search. The Problem Poor distribution of water is evident on an ordinary geographic map of the United States. The more abundant supplies of surface water appear to be centered in the northeast, the southeast, and the central humid areas of the country. It is in the midst of this abundant surface water, in the Ohio River Valley, that most of the bituminous coal is mined. Varied industry has located in the valley to use the coal and the river. The coal is a source of power and o raw material. The river provides transportation for raw and finished materials; equally important, it provides the water that is used for cooling and processing in manufacturing. It also serves as a vehicle for the disposal of waste.

Jan 1, 1962

By L. Vinnett, I. Panire, J. Yianatos, F. Ruiz

"The effect of operating variables on the flotation performance at steady-state has been extensively used for modelling and simulation of separation processes. However, the dynamic characterization of key variables such as gas dispersion (Sauter mean diameter of bubbles, D32, and bubble surface area flux, SB) and froth discharge rate is rather scarce. In this paper, an experimental design allowed identifying the dynamic response of the flotation process in a laboratory scale flotation cell, using a two-phase system, airwater. The installation included automatic control for the superficial gas rate, JG, and the pulp level. Gas dispersion was evaluated in terms of the Sauter mean diameter of a bubble population and the bubble surface area flux, SB = 6·JG/D32. The D32 was measured using the McGill Bubble Size Analyzer (MBSA) along with a semiautomated algorithm. In addition, the froth discharge velocity was measured in real-time using a Visiofroth system. The control variables were the superficial gas rate and the frother concentration (Teefroth). The dynamic characterization of the flotation process is useful to design algorithms that allow the direct or indirect control of metallurgical variables such as flotation rate, concentrate grade and mineral recovery.INTRODUCTIONGas dispersion indicates the way the gas entering a flotation machine is dispersed throughout the volume of the equipment (Schwarz & Alexander, 2006). The gas dispersion is typically characterized in terms of the bubble size (dB), gas holdup (eG), superficial gas rate (JG), and bubble surface area flux (SB =6·JG/dB) (Finch et al., 2000). All these variables have significant impact on the metallurgical performance of flotation machines. For example, Perez-Garibay et al. (2014) investigated the effect of the particle size, bubble size distribution, superficial gas rate and collector dosage on the flotation performance, for the separation of a sphalerite mineral. The authors observed that recovery increased with the superficial gas rate ranging from JG = 0.04 to JG = 0.08 cm/s and also a maximum recovery was obtained for bubble size close to 300 µm. Gorain et al. (1998) reported a strong correlation between the flotation rate constant and the bubble surface area flux in a zinc cleaner circuit. Both variables were directly proportional at three froth depths in the range of hF =7 - 45 cm. Dobby & Finch (1986) incorporated the effect of the superficial gas rate and the bubble size on the flotation efficiency by means of a kinetic model for the rate constants. Yianatos & Contreras (2010) developed a model to estimate the carrying capacity in large flotation cells by including the bubble surface area flux."

Jan 1, 2016

By Paulo Rogério Minatto

A corrosão provocada pelo CO2 associada ao tipo de escoamento é uma das mais agressivas ao aço de baixo carbono o API X65. O petróleo extraído do pré-sal de baixa profundidade apresenta maior concentração de CO2 podendo aumentar os pontos de corrosão nos equipamento e nas tubulações. O dióxido de carbono sendo um óxido ácido em contato com a água forma o ácido carbônico que reage com o metal formando camadas protetoras de óxidos ou de carbonatos. Essas camadas que ficam entre o metal e o fluído tendem em alguns casos atuarem como protetoras, mas à medida que aumenta a intensidade do fluxo essas camadas podem ser rompidas formando novos pontos de corrosão. As indústrias petroquímicas estão investindo em novos processos de perfuração e no desenvolvimento de novas ligas metálicas que possam conter a corrosão provocada pelo CO2 nos equipamento e nas tubulações que transportam o petróleo e seus derivados. Este trabalho tem por objetivo caracterizar a taxa de corrosão por CO2 em condições de fluxo do aço API X65, nas condições normais de temperatura e pressão, utilizando uma bancada de ensaio dinâmico (loop). Mantendo a concentração constante de CO2 em solução aquosa de NaCl 1% foi monitorado o pH, a temperatura e a concentração de íons ferrosos na solução. A taxa de corrosão foi determinada pela perda de massa, estabelecida após os ensaios. Como conclusão observou-se que CO2 provocou uma maior perda de massa para as amostra com maior rugosidade.

Aug 16, 2017

By C. Sarkar

Increased competition in today’s global economy has put mineral industry under excessive pressure to effectively manage production assets to generate business wealth. Capital intensive industry (CII) organizations are seeking ways to manage skill resources, internal processes, and organizational networks with a view to reduce the cost of ownership of assets and increase efficiency of operations and service. The emerging concept of Enterprise Asset Management(EAM) is a collection of business processes that allow CII with right focus on return on investment on assets, to make right decisions on planning, acquisition, maintenance, operation, rehabilitation, and disposal of assets. Information technology (IT) can drive significant returns if the infrastructure covers seamlessly all business processes and all systems, like geographic information system, maintenance management, investment management, laboratory information management, and supervisory control and data acquisition system. The simple approach to IT in the past with disconnected silos of technology, information, and business processes cannot deliver the expected benefits under the modern business environment. Identification of business and application component is a prerequisite for the development of an asset management system that links effectively disciplined processes having characteristics of agility, speed, and integration. This paper discusses various issues and outlines the steps for developing an asset management roadmap in an organizsation. It also presents major business and application components of the system. Keywords: Enterprise asset management, Business architecture, Business component, Application component, Asset ownership, Asset operations, Information technology, Capital Intensive industry

Jan 1, 2003

By H. R. Manouchehri

"In all electrical beneficiation methods, the difference in electro-physical properties of the contributed mineral particles, essentially frictional charge, electrical conductivity and dielectric constant properties are exploited to achieve separation. The composition of the raw material determines what kind of either corona charging, conductive induction, or triboelectric separation method should be employed. The process is versatile and is influenced by different parameters related to mineral characteristics, surrounding ambient conditions and electrical and mechanical attributions of the separating device. Electrical separation is surface based beneficiation method which is mainly affected by the surface and surface changes of the minerals. Therefore, it is essential to understand how the electrophysical properties of the minerals can be changed/modified. During electrical/electrostatic separation process, both charge magnitude and its polarity that developed on the particles and therefore, their electrical beneficiation potential is essentially defined by surface phenomena. Therefore, it is essential to understand how the main electro-physical parameters can be changed/modified with applied surface treatment/pretreatment methods to promote separation. Surface treatment of minerals is carried out by different means, including chemical conditioning, irradiation, thermal treatment, etc. This paper discusses and analyze the electrical separation process, electrophysical properties of the minerals with special focus on the effect of surface pretreatment/treatment methods to affect electrical beneficiation potential of the minerals. The surface treatment methods vary in a wide range from simple surface cleaning to more complicated chemical conditioning and doping. The knowledge of the solid-state physics and chemistry leads to improve the beneficiation potential of different mineral systems by choosing suitable treatment method(s). Despite the complexity and multiplicity of the charging mechanisms, difficulties in separating fines it seems to be beneficial make our attempts to further investigate and develop the process as dry, low cost beneficiation process, especially nowadays when environmental concerns, as well as energy and water consumptions are main concerns for mining industry."

Jan 1, 2018

By Sakshi Hazuria Anderson, Angela Binder, Oscar Jaime Restrepo Baena, Simit Raval, Sandra Nowosad

As the mining industry faces times of change, new challenges arise to ensure raw material supply for the younger and future generations. Different scenarios are currently shaping the way we mine and teach mining engineering. Led by an increasing demand for raw materials, net zero requirements for improving long-term operation performance, technological advancements such as automation and digitalization, safety improvements, environmental considerations and a need for social acceptance, mining is pursuing to change and adapt to these requirements at a faster pace. Such changing times raise new concerns, one of the most relevant is the lower number of students interested or enrolling in mining engineering and related fields leaving mining engineering as one of the less preferred career options between the younger generations. Nonetheless, it is essential to continue addressing and supplying the skill sets that are suited to the contemporary and future mining industry. To this end, globally, academia is currently undergoing several initiatives such as curricula updates and adaptation, up skilling, improving teaching practices and techniques, including e-learning techniques, enhancing industry-academia and inter-university collaboration, and much more. In countries like Australia, where mining plays a crucial role in the economy, the need for curriculum updates is more pressing than ever. As the mining industry evolves with new technologies and sustainable practices, there is a growing demand for a workforce skilled in these modern approaches. Recognizing this necessity, universities such as the University of New South Wales and Curtin University have taken significant steps to revamp their educational programs. By updating their academic offerings, both universities aim to equip graduates with the necessary skills to drive innovation and sustainability in mining, supporting Australia’s development as a leader in this critical sector. Moreover, the selection of topics that drive curricula update and the focus of the research institutions in mining engineering must extend beyond mere technological and technical aspects to include social and ethical dimensions. In this context, the Universidad Nacional de Colombia, in association with the Colorado School of Mines, has introduced the topic of Humanitarian Engineering (HE) in 2020. HE is a socio-technical approach that focuses on developing engineering solutions that promote the sustainable development of communities addressing their basic needs and aiming to improve their quality of life (10, 18). By focusing on sustainable development, community engagement, and equitable resource distribution, HE helps the industry build positive relationships with stakeholders, reduce conflicts, and foster social license to operate. As the mining industry seeks sustainable and socially responsible practices, future engineers require training in this area to understand the broader impacts of their work, fostering a mindset that prioritizes community well-being and environmental stewardship alongside technical proficiency.

Feb 1, 2025

By J M. Marwan, B Tang

Strain-type rockbursts, or strainbursts, are characterised by a localised violent failure. Their cause is attributed primarily to the sudden release of strain energy, which accumulates in a volume of highly stressed rock as a result of mining activities. Examples of such phenomena are crown/sill pillar bursts created in the mining process, pillar crush in room-and-pillar mining, face ejection in drift development headings at depth, and floor bursts associated with deep shaft sinking. The paper describes a simple method for the assessment of crown pillar bursts in steeply dipping ore deposits which are extracted by the overhand cut-and-fill method. The method is based on a theory previously established by the author to help assess the need for a remedial solution such as pillar destress blasting. Basically, the mining-induced energy storage rate (ESR) in the pillar is compared with the critical strain energy to come up with the so-called burst potential index (BPI).

Jan 1, 2001

By Eldridge B. J

During recent years, Central Queensland has experienced a boom in its coal mining industry. This has involved many companies in projects requiring large capital expenditure. As with most projects of this size, many operating problems are now being experienced which were unforseen at the feasibility stage. One of these problems is the failure of pit slopes and spoil piles at some of the strip mining operations. There have been serious stability problems associated with Utah Development Company's strip mining operations in Central Queensland, in particular the Goonyella Mine. A field investigation programme was under- taken to determine the cause of highwall and spoilpile slope failures. Spoilpile failures were found to result from weakness near the spoil/floor contact zone. Highwall failures were found to result from a combination of unfavourable bedding plane dips and weakness, and the presence of joints in weak o~erburdep; Satisfactory solutions fa the staiity, problems are difficult to formulate, and-field stability experimentation is still at an early Stage.

Jan 1, 1974

By N J. Potter, N W. Brand, J M. F Clout

The increasing demand for iron ore with low concentrations of trace elements, puts increasing pressure on iron ore producers for high-quality material. Understanding the mineralogy, petrography, chemistry, and mineral association of iron ore deposits is becoming increasingly important to provide iron ore products that meet the ever-increasing standards of steel mills. Limited attention has been paid to documenting new orebodies beyond bulk RC drill chip assays and product specification data. Therefore, limited information is known about the spatial distribution of minor and trace elements at the hand specimen scale, and elemental deportment within different ore and gangue minerals. In this study, samples from high-grade microplaty hematite, supergene-enriched martite-goethite and hematite iron ores are examined for their elemental and mineral associations. These samples contain distinctive minor and trace element distributions, with the mapping of deleterious elements (eg Zn, As, Cu) enabling the deportment and abundance within the ore and gangue minerals to be assessed. Results from this study show a diverse range of minor and trace mineralogy that are present in typical iron ore samples, in abundances below the detection limit of routine XRD scans, that host the deleterious elements, including but not limited to, sphalerite (Zn and S), chalcopyrite (Cu and S), xenotime (P and Y), apatite (P and Ca), cryptomelane (K and Mn), barite (Ba and S), alkaline feldspar (K, Al and Si) zircon (Zr and Si) and chromite (Cr and Al). The presence of these minerals and associated deleterious elements, even at low concentrations, has implications for producers, with the ongoing restrictions and tightening of environmental constraints in shipped iron ore products. By understanding the distribution and location of these elements within the iron ore, steps can be considered to maintain increasingly higher quality iron ore supply around the world.

Nov 8, 2021

By John M. Dealy, Robert D. Pehlke

Values for interaction parameters in nonferrous systems, as calculated from published data, are tabulated and discussed. The influence of temperature on the parameter is derived and compared with the results of the literature study. Wagner's relationship between the interaction parameter and the self interaction coefficients is compared with the tabulated data. A problem which has been of considerable interest in the field of metallurgy is the prediction of the effect of one alloying element present in dilute concentration on the thermodynamic properties of another dilute alloying element. Ultimately, the prediction may be accomplished entirely from statistical mechanical considerations. At the present, however, the problem remains unsolved since liquid solution models which are simple enough for analytical treatment are inadequate for such purposes. Thus, we desire some means of organizing the information on dilute systems which will serve as a guide for further study on interactions in dilute alloys, and also provide a basis for the utilization of thermodynamic data in the engineering design of alloys.

Jan 1, 1963

By K S. Fisher, J D. Pease

The installation of the George Fisher flowsheet in the lead/zinc concentrator at Mount Isa Mines Limited has recently been completed. The George Fisher flowsheet involved moving flotation capacity from the lead circuit to the zinc circuit and changes in zinc circuitry, changes in the reagent regime and increased regrinding capacity, using IsaMills, to regrind some streams to 80 per cent passing seven microns. The project was highly successful, delivering a five per cent increase in zinc recovery within a fortnight of commissioning. The George Fisher flowsheet was developed over six years. Laboratory work built upon the knowledge gained from investigating and processing the Mount Isa and Hilton orebodies. The engineering design and construction for the brownfield expansion of the existing lead/zinc concentrator had significant involvement from the operational, maintenance and technical personnel. Experienced personnel were seconded from the concentrator to the design and construction groups to ensure smooth integration of the new flowsheet into the existing concentrator with minimum downtime, and maximising the reuse of existing equipment. The combination of thorough design, good project integration with operations, and a good commissioning plan allowed almost immediate delivery of project gains. The project was highly successful, the full design improvements were achieved within two weeks, allowing the focus to move to developing future improvements.

Jan 1, 2000