Search Documents

By S. R. B. Cooke

Certain saturated and unsaturated fatty acids and a variety of resin acids were used as collectors for specular hematite, magnetite, and goethite. Vacuum flotation tests were used with each collector and mineral to delimit the fields of flotation and nonflotation as functions of concentrations of collector and of hydrogen ion. The experimental results of these tests lead to the following conclusions. The respective fatty and resin acids exhibit characteristic fields of flotation and nonflotation for the three iron oxides. The fields are somewhat similar, and specular hematite apparently is the most floatable mineral. The insolubility of some of the organic acids may seriously restrict flotation at low pH, although the saturated fatty acids, caprylic and capric, collect minus-100, plus-150-mesh specular hematite only in acid pulp. The presence of a lower "critical pH" is explained on the basis of the dissociation and hydrolysis of dilute soap solutions.

Jan 1, 1959

By J. R. Cahoon, W. V. Youdelis

FOR the diffusion of copper in silver-rich alloys, there have been only two previous investigations, that of Seith and Peretti in 1936, and that of Sawatzky and Jaumot2 in 1957. Seith and Peretti obtained a value of 24.8 keal per g-atom for the activation energy of diffusion whereas Sawatzky and Jaumot obtained a value of 46.1 keal per g-atom. Admittedly, Seith and Peretti used relatively high concentrations of 2 at. pet Cu and polycrystalline diffusion couples, while Sawatzky and Jaumot investigated tracer diffusion in single crystals of silver. The difference in the results, however, seems too large to attribute solely to solute concentration, as a change of over 20 keal per g-atom in the activation energy suggests a change in the mechanism of diffusion. Therefore, in the present investigation the diffusion coefficient for copper in polycrystalline Ag-2 at, pet Cu alloy is re-established using conventional sandwich-type diffusion couples and electron-probe microanalyses, and the results are compared with those of the previous studies. The diffusion couples were prepared from high-purity silver (99.999 pet) and high-purity copper (99.999 pet). The silver disks, 1/4 in. long and 4 in. in diam, were machined from an ingot which had been solidified in a dynamic vacuum of 10-3 mm of Hg to eliminate oxygen absorption which otherwise would result in copper oxide precipitation in the weld zone. The alloy disks of similar dimensions were machined from an alloy ingot (nominal composition 2 at. pet Cu) which had been unidirectionally solidified to obtain a predictable solute concentration,3 and homogenized for 1 week at 800°C. Sandwich diffusion couples were made by pressure welding an alloy disk between two silver disks in an induction heating coil. The couples were diffusion-annealed at temperatures of 800°, 756°, 699°, and 630°C in tube furnaces in which the temperature was controlled to better than ± l°C. The diffusion couples were examined metallographically for weld defects, and couples showing even minute defects at the weld interfaces were rejected. Concentration penetration curves were established using an A.R.L. Microprobe analyzer. CuKO radiation was counted and converted to concentration using 0.5 and 1.0 wt pet Cu chemically analyzed standards. Initially, four continuous profiles were obtained, and averaged to obtain the final diffusion curve. The initial analysis was performed commercially and the welds were not located with respect to the profile. Therefore, the results were rechecked by the authors using the Mellon Institute A.R.L. probe. In the latter case, concentrations were obtained at 10-µ steps for four different traverses, and then averaged to obtain

Jan 1, 1968

By Michael Robert Hodson

I. Introduction The free market cash price of aluminium in the third quarter of 1985 is approximately $1000/tonne, well below the short as well as the long run marginal costs of production. The current disparity between marginal costs and price, as well as the pattern of prices since their high level in 1980, has led many economists to question whether prices are governed by the 'fundamentals'. Prices, some would argue, are the result of speculation; and speculation is irrational, little influenced by the fundamentals of the industry. The object of this paper is first to examine the relation between the fundamentals and price. A number of simple models are formulated and some empirical evidence is given to show that prices are not very different from costs. There are good reasons why costs and prices have fallen since 1980. Second, the connection is drawn between the fundamentals and speculation. To do this the concept of 'rational expectations' is defined and applied to a model of the aluminium industry. Then speculation is introduced into the model and the characteristics of the solution are examined. The object is to discover the new factors that determine prices and the basic change in the nature of the solution that is caused by speculation. 2. Prices and the Simple Supply-Demand Model Consider a simple model of the aluminium industry. Demand, D, is determined by economic activity, A, given exogenously, and inversely by the price, P. Supply, Q, is determined by the inverse of the rnarginal cost curve, and so varies inversely with exogenous factor costs, C, and directly with price. Price is determined by the equality of supply and demand. Given the equilibrium level of demand, price in this model is equal to the rnarginal cost of producing the required level of demand, P = MC (Dl. Algebraically, [ ] How well does this simple model explain the change in prices during the last five years? Table I shows the LME cash price and the estimated marginal cost of producing consumption during the second quarters of 1980 through 1985. The figures in the table show that price and the marginal cost of supplying demand both fell between 1980 and 1982, rose in 1983 and by 1985 had fallen again. Only in 1984 is the direction of change different. And during the 1980 to 1985 period, marginal costs fell by approximately $560/tonne while the LME cash price fell by $678/tonne. There is a correspondence between the fundamentals of cost and price over most of the individual years and the period as a whole.

Jan 1, 1986

By A. G. Starliper

The Bureau of Mines made laboratory investigations to determine the feasibility of utilizing fine tungsten wires to reinforce a number of nonferrous metals and alloys and a superalloy, S-8l6. The composites of tungsten filament and metals were chosen to attain elevated temperature strength and corrosion resistance. Oriented clean or precoated tungsten wires were incorporated with the other metals by extrusion, swaging, and infiltration casting. Although widely varying characteristics were found in the composites, none were considered satisfactory for high-temperature use, chiefly because of reactions between the matrix metal-tungsten surface. Diffusion, solution, and chemical reactions between matrix and tungsten wires were sufficiently slow for some combinations, such as 15 v/o 8-816, to exhibit increased high-temperature strength for a limited time. A few metals failed to wet or bond to the tungsten surfaces, while a few responded after precoating with a third metal.

Jan 1, 1968

By Hongchun Lou, Yan Zhang, Xianjun Lu

"The potential of Fe(NO3)3 modified attapulgite was assessed for the adsorption of phosphorous removal from aqueous solutions. Natural attapulgite was modified by Fe(NO3)3, and thus the composite adsorption materials could be obtained. Also phosphorous adsorption characterization on the iron-coated attapulgite was investigated in this research. Taken overall the results suggested that phosphorous adsorption capacity could be improved markedly by adopting ferric modified-attapulgite. The optimum phosphorous adsorption were developed in the experimental conditions of the solid-to-liquid Ratio 1g/L, the initial phosphorous concentration 5 mol•L-1, reaction time 120 min, temperature 25 ? and pH=4.0, the removal efficiency is 92.28% for the modified attapulgite. In comparison of batch experimental results of phosphorous adsorption onto natural and iron-coated attapulgite, it has provided much more likely the same change trend. On the other hand, the outcomes of this analysis indicated that ferric modified adsorbent was notably influenced by adsorption element over natural attapulgite. The Freundlich isotherm adequately described the adsorption course of phosphorous onto ferric modified-attapulgite with the correlation coefficient R2 goodness of fit of 0.9690."

Jan 1, 2014

By J. P. Ducarme

Numerous fatal/nonfatal accidents involving underground workers struck by powered machinery occur yearly, with continuous miners and roof bolters involved in the majority of these accidents. In an attempt to reduce these accidents, researchers at the the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory conducted studies of operator interactions with the motions of continuous mining machines and roof bolter boom arms. These operators generally perform their tasks in close proximity to the equipment in confined workspaces, often employing awkward postures. Since experiments with human subjects using the actual equipment were not feasible due to safety concerns, researchers opted to conduct controlled experiments in laboratory settings. Utilizing motion capture technologies and computer simulations, the studies collected data on equipment and operator movement in a range of seam heights and working postures. This article details the results of these studies to examine operating speeds based on usage and seam height.

Jan 3, 2010

By P. G. West-Sells

At Barrick's Zaldivar Copper Mine in Chile, the addition of sulfuric acid to the ore going to heap leaching is a major expense. A process in which a portion of this acid is replaced by elemental sulfur added to the heap has been developed by Barrick and Westcoast Biotech that has the potential for significant cost savings. Initial shake flask tests with plant raffinate solution indicated that oxidation of elemental sulfur by a culture of sulfur-oxidizing bacteria, some indigenous to the Zaldivar heap, showed a significant lag period. This lag period could be reduced by dilution of the raffinate, but dilution would not be economical to implement at Zaldivar. Short (0.75 m) column tests indicated that after the initial lag period, sulfur biooxidation occurred steadily and the acid requirement for obtaining the same copper recovery as the control without sulfur was reduced by as much as 13 kg/t. These tests were followed by taller (5.1 m) column tests that confirmed the reduction in acid consumption, with no negative effect on copper extraction.

Jan 1, 2007

Published experimental data on thermodynamic behaviour of cobalt-containing slags have been reviewed and used in validating a recently developed thermodynamic model. The results from the exercise show that the model provides a reasonably good description of behaviour of cobalt in multi-component slag systems. The models for cobalt containing slags, matte and oxide solid solution phases were incorporated into CSIRO?s multi-phase equilibrium (MPE) package, which was used to calculate the equilibrium distribution of cobalt between matte and slag phases under various conditions. The results agreed well with the experimental data. Furthermore, the good agreement between the calculation and the plant data indicates that the operating conditions of industrial smelting and converting processes are close to equilibrium. Two diagrams showing the effects of slag chemistry and SO2and O2partial pressures on the distribution of cobalt between phases were generated for conditions similar to smelting and converting processes. These diagrams provide some useful guidelines for developing new strategies to improve cobalt recovery.

Jan 1, 2004

By Val E. Payne

Issues between resource utilization and resource preservation often develop in connection with coal mining. One such conflict exists in eastern Utah where PacifiCorp and Energy West Mining Company are working with State and Federal agencies to address the resource recovery/resource preservation dispute. The effects of underground longwall coal mining on golden eagle (Aquila chrysaetos) cliff nesting sites have been studied at the Cottonwood Mine since 1986. Subsidence, escarpment spalling, and the nesting activities of the local eagle population were monitored.

Jan 1, 1986

By Klaus Schwerdtfeger, Leo Zwell

The equilibrium between Ir-Fe or Rh-Fe alloys, iron oxide (wüstite or magnetite), and CO2-CO atmospheres has been determined at 1200°C. The data are used to derive the activities in these binary solid solutions. Both systems show negative deviations from Raoult's law. The lattice parameters are given for the investigated Ir-Fe and Rh-Fe alloys. IRIDIUM and iron form a continuous series of fcc solid solutions at elevated temperatures.' Rhodium-rich Rh- Fe alloys have fcc structure.' In the medium concentration range an ordered bcc phase is stable at temperatures up to about 1300°C. Phase relations in iron-rich alloys are not well-known. No thermody-namic data are available for these alloys. EXPERIMENTAL METHOD The experimental method used was to measure the equilibria between a gas phase of known CO2/C0 ratio, the alloy, and iron oxide (wüstite or magnetite). In one series of experiments the alloys of known composition were heated in CO 2-CO gas mixtures. After treatment (usually 1 day) the sample was quenched to room temperature and its surface examined visually to determine whether an oxide tarnish had formed. The procedure was repeated at slightly higher CO 2/CO ratios until the CO 2/CO ratio of incipient oxidation was found. Subsequently, the CO 2/C0 ratio was lowered again in small increments until the tarnish was reduced. In other experiments mixtures of alloy and iron oxide powders were pressed into pellets and equilibrated with the CO2-CO gas phase. In order to ensure that equilibrium was attained, two specimens with different starting iron content were heated side by side; in most cases, equilibrium was approached in one pellet by reduction of iron oxide and in the other pellet by oxidation of metallic iron. The sample was quenched to room temperature, and the composition of the equilibrated alloy was determined by X-ray measurements of lattice parameters and comparison of these values with calibration curves obtained from alloys of known composition. The oxides present in the specimens were identified by comparison of their diffraction patterns with those in the ASTM Card File. It may be expected from the noble character of iridium and rhodium that no appreciable amount of iridium or rhodium is dissolved in wiistite and magnetite under the present experimental conditions. The activity of iron in the alloy is then equal to that established in the iron oxide by the COrCO atmosphere. The activities of iron in wüstite and magnetite, as a function of oxygen pressure, were taken from the work of Darken and Gurry,

Jan 1, 1969

Jan 1, 2003

By G. B. Craig, G. L. Montgomery

A simple technique has been developed which reveals glide dislocations in zone-refined aluminum as etch pits. The technique has been tested quantitatively by making dislocation counts on aluminum single crystals deformed in pure bending. The method has the advantage of being insensitive to the orientation of the surface under examination. A number of etchants which will reveal dislocations in annealed aluminum have been reported.'-' These etchants apparently depend on decoration of the dislocations by an impurity (probably iron) and cannot, therefore, be used to reveal fresh glide dislocations. In addition, it is unlikely that screw dislocations will be etched because of their small attraction for impurity atoms. Amelinckx6 has reported that glide dislocations located along slip traces can be revealed by fluo-rated aqua regia. This work indicated that dislocations themselves, irrespective of decoration by impurity atoms, are responsible for the etch pits. However, as a result of additional etching experiments, Wyon and Marchin7 concluded that dislocations alone are not sufficient to explain the localization of etch pits on slip lines in aluminum using chemical etch-pitting techniques. In addition, their results show that glide dislocations are revealed only on surfaces approximately parallel to a (100) axis and that not all slip systems are attacked. These observations have been confirmed by the present authors. The technique described in this article is insensitive to the orientation of the surface, and reveals dislocations on all glide systems. Fig. 1 shows a deformed region in the neighborhood of a scratch. Dislocations can be seen along three slip traces. In the present work, single crystals of zone-refined aluminum are polished for from 2 to 5 min in a chemical polishing reagent held at 100°C, as described by Herenguel and second:' H2Sol 60 pct H3PO4 30 pct HNO3 10 pet The samples are then coated with a thin oxide film by annealing in air at 450°C for 1 hr and cooling in the furnace. After deformation, dislocation etch pits are developed by immersing the specimen in the same polishing solution which is now held at a temperature of 50°C. The formation of small hydrogen bubbles indicates that etching has occurred. The sample is immediately removed from the solution. Prolonged etching results in enlargement of the pits and, in regions of high dislocation density, the overlapping and loss of resolution of individual pits. It is the experience of the authors that contact with iron will ruinously contaminate the reagent. With careful etching, dislocations separated by half a micron can be resolved optically and the method has been shown to be sufficiently sensitive to reveal dislocations produced during the pre-easy glide region of deformation, Fig. 2. A few examples of glide-dislocation configurations, as revealed by this technique, are shown in Figs. 1 to 4.

Jan 1, 1964

By Arthur F. Taggart, Nathaniel Arbiter

The fact that the floatability of minerals with fatty-acid collectors changes as the pH of a pulp varies was utilized in the early days of flotation, when sulphuric acid was used with oleic acid to float sphalerite and galena. from gangues which themselves float with fatty acids in alkaline pulps. Gaudin1 showed that this difference in floatability is a regular function of the extent of the change in pH. The present paper offers an explanation of the phenomenon, and on the basis thereof sets up recommendations for control of soap-flotation operations. Experimental Parallelism between floatability of a mineral in a given environment and its contact angle in that environment is so well established,2 and the contact angle is so readily and rapidly measurable, that contact angles have been used throughout the experimental work to indicate relative floatability. Experiments comprised contact-angle measurements on a number of representative minerals and metals, and a variety of subsidiary tests designed to check and to amplify the contact-angle indications. Contact-angle measurements were made by the method described in detail by del Giudice.3 Sequence of procedure for determination of the points of Fig. I was: I. Polish specimen. Most specimens yielded zero contact angle after polishing; a few showed a slight "cling." Cling is characteristic of specimens that pit on polishing; it is due to a residue of organic contamination, originally on the particle surface, which persists in the pits. The cling did not change total contact angle after conditioning, and is not, therefore, additive in the upper part of the curves of Fig. I. It may have broadened the bases of the curves for the affected minerals slightly. 2. The specimen was next conditioned in soap solution for 5 minutes. 3. The conditioned particle was transferred, under conditions that precluded surface drying, to an aqueous solution of the pH desired and contact angle determined. 4. The particle was thereupon transferred, again without surface drying, to water. The confirmatory tests will be described at the places pertinent in the argument. Discussion of Results Gaudin and Vincent4 have shown that contact angles with heptoic acid as a collector decrease for a given specimen when the concentration of collector present falls below a certain value. A similar reduction in angle occurs with collector-conditioned particles that are visibly slime-coated, and varies roughly with the extent of coating. Since in the last case the reduction in angle is certainly due to reduction in the proportion of total conditioned mineral surface presented to the bubble, the authors believe that the same condition prevails in the first case cited, and that similar reduction in angle and floatability will occur whenever starvation quantities of collector are present, whether by design or by reason of excessive consumption.

Jan 1, 1943

By Nathaniel Arbiter, Arthur F. Taggart

The fact that the floatability of minerals with fatty-acid collectors changes as the pH of a pulp varies was utilized in the early days of flotation, when sulphuric acid was used with oleic acid to float sphalerite and galena. from gangues which themselves float with fatty acids in alkaline pulps. Gaudin1 showed that this difference in floatability is a regular function of the extent of the change in pH. The present paper offers an explanation of the phenomenon, and on the basis thereof sets up recommendations for control of soap-flotation operations. Experimental Parallelism between floatability of a mineral in a given environment and its contact angle in that environment is so well established,2 and the contact angle is so readily and rapidly measurable, that contact angles have been used throughout the experimental work to indicate relative floatability. Experiments comprised contact-angle measurements on a number of representative minerals and metals, and a variety of subsidiary tests designed to check and to amplify the contact-angle indications. Contact-angle measurements were made by the method described in detail by del Giudice.3 Sequence of procedure for determination of the points of Fig. I was: I. Polish specimen. Most specimens yielded zero contact angle after polishing; a few showed a slight "cling." Cling is characteristic of specimens that pit on polishing; it is due to a residue of organic contamination, originally on the particle surface, which persists in the pits. The cling did not change total contact angle after conditioning, and is not, therefore, additive in the upper part of the curves of Fig. I. It may have broadened the bases of the curves for the affected minerals slightly. 2. The specimen was next conditioned in soap solution for 5 minutes. 3. The conditioned particle was transferred, under conditions that precluded surface drying, to an aqueous solution of the pH desired and contact angle determined. 4. The particle was thereupon transferred, again without surface drying, to water. The confirmatory tests will be described at the places pertinent in the argument. Discussion of Results Gaudin and Vincent4 have shown that contact angles with heptoic acid as a collector decrease for a given specimen when the concentration of collector present falls below a certain value. A similar reduction in angle occurs with collector-conditioned particles that are visibly slime-coated, and varies roughly with the extent of coating. Since in the last case the reduction in angle is certainly due to reduction in the proportion of total conditioned mineral surface presented to the bubble, the authors believe that the same condition prevails in the first case cited, and that similar reduction in angle and floatability will occur whenever starvation quantities of collector are present, whether by design or by reason of excessive consumption.

Jan 1, 1943

By Ronald C. Koo

SMALL additions of potassium, aluminum, and silicon as oxides (referred to as dope) to tungsten have been known for several decades to have a very large effect in raising the recrystallization temperature and altering the recrystallized grain morphology of heavily drawn wire. Previous investigations of this doping effect1 6 have led to various speculations but all failed to deduce unequivocally the physical state or the mechanistic influence of the dopant. Recently, walter7 has observed, by transmission electron microscopy, strings of "fine particles" in heavily rolled and annealed doped tungsten sheet and concluded that they were particles of mullite (Al6Si2013). His conclusion was inferred from the electron diffraction patterns of large particles ex-trated by carbon replication of fractured surfaces of slabs rolled from sintered ingots. That the strings of "fine particles" in heavily rolled and annealed sheet were also mullite was an assumption for which no evidence was presented. A similar investigation has been carried out in this laboratory over the past 2 years on a variety of tungsten wire: doped tungsten, and undoped tungsten, as well as 218 doped tungsten purchased from the Lamp Metals and Components Department of the G.E. Lamp Division. Although the electron microscope observations are similar to those reported by Walter, the writer has reached a different conclusion concerning the physical state of the dopant in annealed tungsten. The purpose of this communication is to present evidence that the strings of "fine particles" observed in transmission specimens are not mullite, but are voids. In the present investigation, tungsten wire, 0.88 mm in diam, was rolled into ribbon 0.2 mm by 125 µ thick. The ribbons were annealed in vacuo at a pressure of -1 x 10-5 Torr and then thinned electrolytically in a 2 pct KOH solution. Fig. 1 shows a typical transmissicjn electron micrograph of a sample annealed at 1700°C for 30 min which reveals rows of closely spaced voids having a light contrast (referred to as "fine particles" by Walter) aligned parallel to the working direction. Stereo micrographs (by D. Moon, Westinghouse Research and Development Center) have shown that these voids do not exist on the surfaces of the specimens as a result of thinning but are within the thin-foil specimens. The following experiments have been performed to verify that these are indeed voids. I) Effect of Annealing. Voids are absent in unannealed specimens and appear only after annealing. This behavior cannot be explained if they were solid particles such as mullite. Precipitation (in an unquenched specimen) upon annealing requires solute elements having decreasing solubilities with increasing temperature. Although the solubility of aluminum in tungsten does decrease with increasing temperature, precipitation requires a concentration in excess of 1.4 wt pct,8 which is at least two orders of magnitude higher than the aluminum content in doped tungsten. It is also unreasonable to assume that particles aligned in rows initially present in unannealed specimens were too

Jan 1, 1968

By C. W. Haworth, M. G. Hall

THE diffusion of copper in silver has been studied by Sawatzky and Jaumot1 and Cahoon and Youdelis.2 Sawatzky and Jaumot measured tracer diffusion in single crystal specimens but the 12.9 h half-life of CU64 limited the time of the diffusion anneal to about 50 hr, and in consequence the minimum temperature of the investigation was 716°C. Cahoon and Youdelis employed polycrystalline diffusion couples, and measured the interdiffusion coefficient over the range 0 to 2 at. pct Cu. These experiments were performed at temperatures down to 630°C and a discontinuity in the Arrhenius plot was observed at -700°C. The high D-values at lower temperatures were attributed to the effect of grain boundary diffusion. The present experiments were undertaken to investigate this anomaly and study the low temperature region of the diffusion of copper in silver. The method employed single crystal samples and a plated source of copper. Silver single crystals 2½ by 4 in. sq were grown from zone-refined silver bar (>99.99 pct Ag) by the Bridgeman technique, and $ in. thick slices were cut by spark machining. The specimens were electro-polished, and a 2 µm layer of copper was electroplated on to the planar surface at one end of each specimen using a potentiostatic voltage source. The following solution was used for plating: CuSO4 . 5H2O 125 gm H2SO4 (S.G. 1.8) 53 ml H2O 1000 ml The diffusion couples were sealed in capsules, in an argon atmosphere, and were annealed at either 701, 597, or 498°C. The temperature measurements were made to an accuracy of *l°C After the anneal, the penetration of copper into the silver was determined using an electron probe micro-analyzer. 100 sec scaler measurements of the intensity of Cu Ka! X-radiation were performed at 2 to 5 µm intervals along a line normal to the source, with a beam potential of 25 kv. Allowances were made for the background radiation, and the dead-time of the counting system in the normal way, and the intensity ratios were corrected to weight concentration by the method of Duncumb & de-Casa.3 For the analysis of the diffusion profiles, it was first observed that the copper layer did not completely dissolve in the host crystal for the specimens annealed at 498 and 591 whereas for the specimen annealed at 701°C, a single phase solid solution was formed. For the 498" and 597°C specimens, the concentration of copper in the silver at the interface was therefore constant throughout the anneal and the analysis for a

Jan 1, 1970

By Y. L. Yao

It is suggested that the binary alloy systems of transition metals may be classified into groups according to "excess energy"E. For systems with positive ?E, the Laves phase, the TiNi3-, the TiCu3- and the Cudu-type rich in the smaller atom and the TizNi-type rich in the larger atom may exist. For systems with negative ?E and composed of two components of different crystal structures, the X, the Cr3O and the phase may exist on the side of the phase digrattz rich in the component with the higher "solubility factor" value am! the Cudu-type and the disordered hcp phase on the other side; if the crystal structure of two components is the same, the Cudu-type may exist on both sides. For systems with weakly positive ?E and cotnposed of different crystal structures, the u phase and the MgCd3-type may replace the Laves phase and the other types; the X, the Cr3O and the a phase may also exist. Finally, the equirnolar compounds of the CuAu- and the CsC1-type may exist irrespective of the sign of ?E. THERE are many factors which play a major role in the formation of binary intermediate phases in alloys, such as the crystal structure, the electronic structure, the atomic size and the electrochemical factor. To find the simultaneous effects of all these factors on the formation of intermediate phases of every metal would be a difficult task, especially because only a small fraction of experimental facts necessary for the complete formulation is known at present. Thus the past surveys of intermediate phases have been usually confined to few metals, several types of intermediate phases and some but not all controlling factors. In a previous paper1 the idea of "solubility factor" of metals was introduced. Although the suggested values are tentative and empirical, the formation of a continuous series of solid solutions in metals could be correlated with the interplay among the atomic size factor, the solubility factor and the crystal structure factor. The purpose of this paper is to demonstrate qualitatively the interplay of these factors in the formation of binary intermediate phases among transition metals. FACTORS CONSIDERED The Crystal Structure Factor. With rare earths excluded, the transition metals are classified into three common crystal structures listed in Table I. There is arbitrariness in the present classification of several allotropic elements. However, out of seventy-odd continuous solid solutions formed among transition metals, only six of them, namely, those

Jan 1, 1962

By J. Jackman

North America has been aggressively pursuing approaches to improve the fuel efficiency of vehicles, and to develop alternatives to petroleum-based fuels used in automotive applications, for over ten years, Increasing energy demand due to emerging economies, coupled with probable peaking of conventional petroleum production in the coming decades are increasing the need to reduce dependence on petroleum-based fuels for transportation, Vehicle lightweighting is seen as an important strategy to improve fuel efficiency of conventional as well as highly innovative vehicles, Magnesium has recently emerged as a serious candidate for lightweighting, as a result of lower global prices, Automotive vehicles produced in North America currently use more Mg than vehicles produced elsewhere in the world, but the amounts per vehicle are very small in comparison to other materials such as steel, aluminum and plastics, The reasons, besides price, are primarily a less-developed state of technology for Mg in automotive transportation applications and lack of familiarity by the vehicle manufacturers with the material, This paper reviews the major government-funded research programs in the USA and Canada that are dedicated to advancing the state of Mg technology for automotive applications, It provides examples of research in the areas of high-pressure and other types of castings, corrosion solutions, sheet development and other wrought applications.

Jan 1, 2006

By S. Castro

Hydrolysis of metallic ions depends on pH and the products of hydrolysis either activate flotation or can lead to inadvertent activation of gangue particles, but can also depress flotation of valuable components. One of the most recently studied topics is the use of seawater in flotation. Seawater is a concentrated NaCl solution (about 0.6 mol/L) that also contains considerable amount of Mg2+ and Ca2+ ions. The hydrolysis products of Mg2+ strongly depress flotation of molybdenite over the pH ranges over which they form in the process water. This effect can be eliminated by removal of hydrolysing ions from the process water or by carrying out the flotation at the pH over which such a hydrolysis can be avoided. The former can be exemplified by prior precipitation of the harmful hydrolysing ions as, for example, in the University of Concepcion Patent. The latter can be exemplified by the use of metabisulfite to depress pyrite in the flotation of Cu-Mo sulfide ores in seawater, the process that is carried out at much lower pH, which avoids formation of Mg2+ hydrolysis products.

Jan 1, 2017

By P. Chris Pistorius

"Ilmenite smelting involves partial reduction of iron oxide from a slag consisting mainly of T1O2, T12O3 and FeO, yielding as products iron (with approximately 2% carbon) and titanium slag. Slag purity requirements preclude any fluxing additions, and the aggressive nature of the slag necessitates a furnace freeze lining. Large departures from thermal and chemical equilibrium hold in the smelter, with possible implications for process stability. The slag is approximately 150K. hotter than the metal, which means that the metal temperature is below the slag melting point; this difference in temperature has been shown to lead to formation of a solid TisOs-rich layer between the slag and metal. Recent equilibrium measurements have confirmed that the slag and metal are not in chemical equilibrium either, with significantly more reducing conditions in the metal than in the slag. After solidification, the pseudobrookite slag structure is metastable below approximately 1400K, and may transform upon slight oxidation.IntroductionThe natural mineral ilmenite is the main source of titanium, which is mainly used to produce Ti02-based pigments. Ilmenite has the ideal formula FeTiC>3, but natural minerals can be partially oxidized (to contain some Fe3+), and typically contain MnO and MgO as well, together with associated silicate minerals. Smelting is one of the methods to upgrade ilmenite for subsequent T1O2 pigment production; smelting involves partial reduction of FeO to form metallic iron as a byproduct and titanium slag as the main product. Reduction is typically controlled to yield a slag which contains around 10% FeO, 85% (Ti02+Tij03) and 5% impurity oxides (mainly MnO, AI2O3 and S1O2). An example of a typical average slag composition from reduction of South African ilmenite is shown in Table I. As this indicates, a significant side reaction is reduction of some T1O2 to T12O3. The relative extents of reduction of FeO to Fe and of Ti02 to T12O3 are such that the slag stoichiometry is close to that of the pseudobrookite phase [1]. Pseudobrookite has the structure AB2O5 (where ""A"" and ""B"" are different cation sites); the phase which makes up the bulk of solidified titanium slag has the AB2O5 structure and stoichiometry [2], and can be viewed as a solid solution of FeTi20s, T13O5, ÌçÔÀ2è5, MgTi20s, AI2T1O5 and C^TiOs [1]. This solid-solution phase is referred to as ""pseudobrookite"" or ""M3O5"" in this paper."

Jan 1, 2012