Search Documents

By Rodney L. Stone, David S. Cahn

As part of an over-all laboratory and plant test program to determine mixing ad other techniques for a more economic use of bentonite as an iron ore pellet binder, a settling test for measuring the bentonite content within a pellet or a batch of pellets has been developed. Through this test, it has been shown that dry fracture load is directly proportional to bentonite content in batches of pellets, but inversely propor tional to bentonite content in individual pellets of the same batch. This apparent paradox is explained by a negative correlation between a pellet's size and its bentonite content and the fact that large pellets can withstand a higher fracture load than small pellets. In past attempts to characterize green and dry iron ore pellets, the authors found large variations in the results of strength tests on closely sized pellets from the same batch.' Reasons advanced for such variations in the quality of pellets in which the binder is bentonite were the presence of internal flaws and the nonuniform distribution of the binder. Even when resulting pellet strength is good, there is still the question of whether the same strength could have been attained through a more effective use of a smaller amount of bentonite. The authors' own and other studies 2-3 have pointed out the strong dependence of pellet strength on the degree of "mixedness" of the iron ore concentrate and the bentonite binder. However, before such a relationship could serve as a guide for the development of better mixing techniques and the associated economy of

Jan 1, 1969

By D. E. Wolfson

As part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report.2/ The suitability of coal for metallurgical use depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, as well as the available reserves, are considered in selecting coals for carbonization tests. According to the estimate of reserves by Dowd,3/ the recoverable coal in Raleigh County in beds 28 inches or more thick, in thousand tons, is: [ ]

Jan 1, 1957

By Robert Thomas

DURING the past 20 years the advantages of reinforced concrete as a substitute for timbering in so-called permanent mine openings have been fully recognized, and its use has become almost general practice in the larger mines. The term "permanent mine openings" is used advisedly and is assumed to embrace such openings as ventilation shafts, material shafts and main hoisting shafts, with their adjacent stations, ore pockets, etc. In the concreting of such openings, the actual cost as compared with that of timbering has been of secondary consideration, the support of large openings, elimination of fire hazards, and prevention of inter-ruptions to production being the primary objectives. The ultimate economy, however, of lining such openings with concrete when they are to remain in use during the entire life of the mine, and especially when they are in bad ground, will seldom be questioned. During this 20-year period there have appeared in engineering publi-cations a number of interesting articles on the use of concrete in mines, nearly always describing some specific project of major proportions, such as the concreting of ore pockets, large stations or main hoisting shafts. Such articles are unquestionably of interest, since the projects require considerable engineering thought, not only in the method of excavating large openings, but in their engineering design as well. Concreting of main hoisting shafts, particularly when this is done with the least possible interruption to production, provides some interesting problems. The concreting of haulage drifts of the dimensions commonly found in mines, on the other hand, soon develops into a routine operation, there-fore it is with some hesitancy that the author attempts to prepare an article on this subject. The writer can recall only one article on the concreting of mine haulageways, although several articles have been written concerning the concreting of tunnels considerably larger in dimensions than those required in general mine practice.

Jan 1, 1936

By Mariam Melashvili, Chris Fleming, Rene Jackman

"A study was undertaken to develop a flowsheet for treating a high grade silver/gold ore body by cyanidation, CCD and Merrill Crowe precipitation, with tailings detoxification to meet stringent limits for cyanide and thiocyanate concentrations in the final discharge. In one of the flowsheets examined, free cyanide in the final leach liquor was recycled to the mill where it was hoped that it might react beneficially with fresh ore to reduce the cyanide makeup by an equivalent amount. However, laboratory results suggested that most of the cyanide recycled to the mill reacted with iron forming a soluble ferrocyanide complex. This would have had a negative impact on cost, not only because the cyanide recycled to the mill could not be claimed as a credit, but also because the presence of ferrocyanide in the final tailings meant copper sulphate had to be added to the SO2/air cyanide detoxification process to precipitate the iron cyanide. In an alternative flowsheet that was examined, recycling of cyanide to the mill was abandoned, and this allowed the milled slurry to be pre-aerated in a single mixing tank before cyanidation. During alkaline pre-aeration, any ferrous ions that are generated in the mill are oxidized to ferric ions, which, unlike ferrous ions, are inert in cyanide solution. This significantly reduced cyanide consumption and lowered costs in the detoxification of the tailings. In this paper, the cost implication of these two circuits is compared.INTRODUCTIONMost of the gold that is produced by hydrometallurgical processes is recovered by cyanide leaching. The reason for that lies in the superior thermodynamic stability of the gold cyanide complex and the favorable economics this confers on the process (Fleming, 2014). However, the gold in most of the gold-bearing ores processed is a very minor component, and therefore, the leaching response is often dominated by that of the host minerals.Many gold ores treated by the cyanidation process contain iron minerals. Cyanide reacts readily with some iron minerals forming ferrocyanide as one of the compounds. Ferrocyanide is stable when solutions are exposed to air and does not retard the dissolution of gold. In fact, it has been claimed that potassium ferrocyanide in the presence of oxygen is a weak solvent for gold (Hedley & Tabachnick, 1958). The main problem with the formation of this compound is the consumption of cyanide. Ferrocyanide contains six molecules of cyanide for each atom of iron {Fe(CN)64-} so the wasteful consumption of cyanide is greatly increased by its presence. Thiocyanate is also often produced during the reaction of certain iron sulphide minerals with cyanide, and contributes to the wasteful consumption of cyanide. In addition, environmental regulations in certain countries demand that thiocyanate be removed from the tailings, and this adds significantly to the cost of tailings treatment."

Jan 1, 2016

By J. J. Stacey

Large mining companies generally follow the distributed ownership corporate model, with a board of directors responsible for decisions that affect both shareholder value and stakeholders of the company. The board is simultaneously responsible for setting the culture and values of the corporation, which drive performance and priorities. Companies listed on the Johannesburg Securities Exchange (JSE) commit to sustainable development in various ways, either by virtue of implementing the King Code of Governance 2009 (King III) and/or through their own public reporting on social and environmental matters. Many mining companies make public statements regarding their support for environmental stewardship, ethical behaviour, and fair treatment of communities. It is a local, regional, and indeed, global phenomenon that companies fail to deliver on these statements. Research was carried out through the Institute of Directors of Southern Africa in 2007, and followed up in 2012, regarding directors? understanding of sustainable development issues, the relative priorities, what is needed for ?radical change? to effect sustainable development, and what enables or constrains the latter. Pertinent findings of both surveys are presented in this paper, and it is suggested that ?on-the-ground? performance may be indicative of the nature of leadership and decisions in the topmost ranks of the company. The results indicated that environmental concerns fall consistently below social issues. Financial capital ranked most important, and while environmental issues are recognized as being of strategic concern for the long-term, they ranked as being the lowest importance of all ?Five Capitals? (Financial, Manufactured, Social, Human, and Natural). Social capital ranked second lowest, with black economic empowerment being the only high-priority social issue. There is also evidence that certain companies within the mining sector fail to recognize their absolute dependence on natural resources. Much is made in academic and popular literature of the need for a new type of leadership for the radical shift to sustainable development: at company level this implies therefore a new type of director. The research found that only 14 per cent of directors felt that board decisions are consistent with their personal values; while intentions are strong to behave ethically and serve sustainable development, actions to give effect to these intentions lag significantly. Respondents indicated that the top impediments to courageous leadership for sustainable development related to personal issues of maintaining the image of being a director, fear of appearing weak, fear of being a lone voice, and bowing to board-colleague peer pressure.

Jan 1, 2014

By L. S. Darken

IT has been known for sometime that in an ionic lattice, such as that of Ag2S or FeO, the migration velocity of the anion may differ markedly from that of the cation, the cation being usually the more mobile. It has been shown, for example, that during the formation of silver sulfide tarnish on silver, the tarnish layer grows principally by the motion of silver cations through an essentially stationary silver sulfide lattice. Similarly, the growth of wüstite scale on iron proceeds principally by motion of iron ions, this being accomplished with the aid of vacant iron lattice sites into which the iron may readily move. Likewise investigations of solid solutions of various salts show that there is usually considerable difference in the mobility of the different cations. Measurements of the mobility of various metals in liquid mercury indicate that the various metals move at different rates relative to the mercury. In view of the foregoing it seems reasonable to suppose that when any single phase solution is acted upon by a field, the atoms of different elements respond in different ways; in particular, that the force arising from a particular concentration gradient in a binary alloy would cause the atoms of one component to move with a drift velocity which is in general different from that of the atoms of the other component. The recent experiments of Smigelskas and Kirkendall1 support this viewpoint, since they found, in essence, that during diffusion in alpha brass zinc moves appreciably faster than copper. This was evidenced by the relative motion of inert molybdenum wires. Such a phenomenon is incompatible with the place interchange theory of diffusion proposed by several authors, most recently by Birchenall and Mehl.2 This theory has, however, also been questioned3.4 for other reasons, principally because of the high energy required for direct atomic interchange. The rather large difference between self-diffusivity, as determined by tracer technique, and mutual diffusivity, as determined with the aid of another element at low concentration, might also be interpreted as favoring the above idea; however, Birchenall and Mehl have pointed out that there is another possible interpretation of this difference; this is discussed later. A rather interesting and pertinent observation was made by Schwartz,5 who noticed that tungsten lamp filaments, heated by direct current, commonly fail by necking down in the region at the temperature gradient near the positive end, with a concomitant swelling at the corresponding position near the negative end. He introduces considerable auxiliary evidence to show that this phenomenon is occasioned by the motion of tungsten cations which migrate in the high temperature region from the positive end toward the negative end. The mechanism of this migration is not clearly understood. If, however, this experimental evidence be accepted, we are forced to conclude that alloying elements in the tungsten may migrate by the same or a similar mechanism, whatever it may be, at a greater or lesser rate, thus giving rise

Jan 1, 1948

By C. Sist, J. Shannon, J. Fossenier, J. F. Adams

With the cleanest and easiest to treat copper concentrates dwindling and becoming harder to find, electrorefineries must deal with the reality of higher impurity anodes. There are well-known strategies for managing nickel, bismuth, antimony, etc. using bleeds (Ni, Bi, Sb, As) or arsenic control (Bi, Sb) or hydrometallurgical add-on circuits (IX, MRT, SX for As, Bi, Sb). However, for integrated copper producers and those producing other base metals it is often worth considering a more holistic, global approach. This paper will discuss both the well-known strategies as well as some global strategies and the role that hydrometallurgy can play in them. Examples will include atmospheric and pressure leaching, selective precipitation and impurity recycling or fixation. INTRODUCTION In the electrorefining of copper, impure copper anodes are electrically corroded, and pure copper is deposited on cathodes by passing DC current through an acidic copper sulphate solution. The anode copper impurities either settle to the cell bottom as insoluble components (anode slimes) or remain in solution with minimal deposition at the cathodes when correct operating parameters are maintained. Consideration of impurities is important in all copper electrorefineries. A typical impure anode contains 98.5–99.5% copper (Schlesinger et al., 2011). Table 1 shows the range of impurities reported for all copper anodes in the 2007 survey of operating refineries (Moats et al., 2007). Also shown is an approximate “limit” of anode compositions within which the majority of refineries operate without additional impurity removal capacity (beyond conventional liberator/bleed circuits). The column is somewhat subjective and meant to be an approximation only since there are many factors that influence impurity deportments and refinery impurity tolerances. More recent world survey data from 2013 show the averages for all impurities trending upward from 2003 to 2013 (Moats et al., 2013). With a competitive market for good concentrate and more copper recycling from electronics (which contain high levels of impurities such as nickel, lead and antimony), this trend is expected to continue through the coming years. The traditional primary method of impurity control is refinery bleed through liberator cells which are employed in the vast majority of refineries (Moats et al., 2013). These are used to control copper (primary liberators), nickel, arsenic, antimony and bismuth (secondary and tertiary liberators). Other methods of impurity control include arsenic addition (upstream in the smelter deporting to anode or directly to electrolyte) to control antimony and bismuth (Kamath et al., 2003), ion exchange or molecular recognition technology (Hur et al., 2005; Navarro et al., 2012) for antimony and bismuth. Many refineries also operate nickel evaporators to remove nickel sulphate before recycling back acid. Some use, or are contemplating using, acid purification units to recycle acid and arsenic without nickel and making nickel carbonate (Kamath et al., 2003; Sheedy et al., 2006).

Jan 1, 2019

By Brian P. Stapleton, Bill M. Stewart, Joel R. Warneke, Curtis C. Clark

Of the 28 accident/injury classifications listed by the Mine Safety and Health Administration, handling materials is second only to roof falls in terms of generating the highest number of reportable accidents in active underground coal mines. Two materials-handling activities that cause numerous injuries each year are the categories of ‘handling supplies or material, load and unload’ and ‘moving power cables.’ Mechanization and mine worker activity training are two methods that can aid in preventing these injuries. This paper describes three mechanical methods – the mobile manipulator, the in-mine hoist, and a cable-handling system - being developed and tested at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. Two of the devices are specifically designed for loading, unloading, and moving supplies and materials, and the third device is for handling trailing cables in the confined spaces of coal mines. Also described are safety solutions developed for underground coal mines geared to showing miners safe and unsafe ways of performing various materials-handling tasks.

Jan 1, 2005

By G. C. Marino

The performance of the V-Day Mine near Danville, Illinois has been evaluated from data extending over about a 20 year period. The area included in this study involves over 16 acres. Essentially this entire area has progressively subsided. Extensive data has been collected on the geologic and mining conditions, the subsidence movements, as well as on the response of the surface structures to the subsidence. In this paper a detailed summary of the site conditions is given, and the mechanics of progressive failure of the studied room and pillar mine is postulated. These progressive long-term failures of the V-Day are then compared to other similar mine failures in Illinois. Some overall, but tentative, long-term strength evaluations are presented as well.

Jan 1, 1990

By Roy McKinstry, Mark Rantapaa, Thomas Bolles

"More efficient drilling and blasting techniques have shown measurable improvements in throughput at the Barrick Goldstrike wet grinding mill.A decrease in throughput at the autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the Open Pit and Process areas participated closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of improving throughput in future years, despite the projected harder ores. Plant studies were conducted to determine if adjustments to drilling and blasting could positively influence throughput. At the Goldstrike mill the greatest opportunity from the D2M initiative is realized on the hardest ore. Grinding throughput for softer ore, <15 kWh/st, can meet or exceed the downstream pressure oxidation requirements. Grinding throughput for harder ore, >15 kWh/st, is limited by the SAG milling capacity. Better fragmentation in the D2M ore, as demonstrated by image analysis, increased throughput 5% to 10% (25 to 50 stph) compared to the standard mining methods.Better fragmentation and a subsequent increase in mill throughput were achieved through the use of:1) Electronic caps for more precision and flexibility, as well as for allowing extremely fast shots.2) Explosives with a higher velocity of detonation (VOD), to provide for improved shock energy.3) Improved distribution of the explosives by decreasing pattern spacing.INTRODUCTIONThe Barrick Goldstrike Open-Pit group, along with the Process division, began experimenting with novel blasting technology and techniques to improve mill throughput in the spring of 2001. A series of tests were developed to determine if fragmentation and ultimately mill throughput could be influenced by optimizing the drilling and blasting program in known"

Jan 1, 2004

By Cyril Wells, Robert F. Mehl

The practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out.l,13 This importance lies chiefly, though by no means only, in the study of carbufizing and in the study of reactions involved in the eutectoid inversion in steel. The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in ?-Fe and their mutual effects are measured with precision. The present paper reports the results of measurements of diffusion coefficients D of manganese in ?-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients.‡ Data on the rate of diffusion of manganese in ?-Fe have been reported by Fry2 and by Paschke and Hauttmann.3 Claussen4 calculated the diffusion coefficient D from Fry&apos;s data as 3 X 10-10 sq, cm. per set. at 960º, which will be shown to be incorrect by many orders of magnitude. Paschke and Hauttmann gave a rough value of 9.6 x 10-8 Sq. cm. per set. at 14000. Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon. Method and Materials Method.—The method employed is identical with that used earlier.5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded. The diffusion anneals were performed in argon, except One (test 18) in which hydrogen was employed for purposes noted below. The temperatures reported are accurate to about 3" and constant within 1°C; the diffusion times are reported to the nearest half hour. The specimens were furnace-coo1ed after the diffusion ation, at about 2° per min. Layers, usually 0.004 in. thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0.I Per cent Mn; the distances of these layers from the interface was measured to ±0.0002 in. The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions.8 The D values calculated by these two methods do not differ appreci000. The Grube solution was used except in tests in which the effect of concentration upon D was greater than so per cent; in such cases the Matano method, which explicitly provides for the variation of D with concentration,&apos; is the more reliable. In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer. In 3 of the 3&apos; tests, however, this is not justified, and the D values

Jan 1, 1941

By Cyril Wells, Robert F. Mehl

The practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out.l,13 This importance lies chiefly, though by no means only, in the study of carbufizing and in the study of reactions involved in the eutectoid inversion in steel. The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in ?-Fe and their mutual effects are measured with precision. The present paper reports the results of measurements of diffusion coefficients D of manganese in ?-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients.‡ Data on the rate of diffusion of manganese in ?-Fe have been reported by Fry2 and by Paschke and Hauttmann.3 Claussen4 calculated the diffusion coefficient D from Fry&apos;s data as 3 X 10-10 sq, cm. per set. at 960º, which will be shown to be incorrect by many orders of magnitude. Paschke and Hauttmann gave a rough value of 9.6 x 10-8 Sq. cm. per set. at 14000. Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon. Method and Materials Method.—The method employed is identical with that used earlier.5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded. The diffusion anneals were performed in argon, except One (test 18) in which hydrogen was employed for purposes noted below. The temperatures reported are accurate to about 3" and constant within 1°C; the diffusion times are reported to the nearest half hour. The specimens were furnace-coo1ed after the diffusion ation, at about 2° per min. Layers, usually 0.004 in. thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0.I Per cent Mn; the distances of these layers from the interface was measured to ±0.0002 in. The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions.8 The D values calculated by these two methods do not differ appreci000. The Grube solution was used except in tests in which the effect of concentration upon D was greater than so per cent; in such cases the Matano method, which explicitly provides for the variation of D with concentration,&apos; is the more reliable. In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer. In 3 of the 3&apos; tests, however, this is not justified, and the D values

Jan 1, 1941

By P. H. Dudley

A Discussion of the Paper of Prof. Howe. (Bi-Monthly Bulletin, No. 14, March, 1907, pp. 169 to 274.) P. H. DUDLEY, New York, N. Y. (communication to the Secretary*) :-The characteristics of Prof. Howe&apos;s metallurgical papers are, that he is able, from the mass of confusing evidence on the subject, to make an analysis and present hypothetical and essential principles in concrete form for consideration and discussion. I can appreciate, from the practical side of the subject, the arduous labor of collecting and investigating the data that is essential to prepare the paper. Much of the data necessarily came from material of preceding years. of manufacture in which there was allowed time for chemical reactions of the recarburizer, and for the elimination of the oxidation-products before teeming the ingots. This condition gave a favorable tinge-element to free the metal from slag- and other impurities, but, in allowing the. ingot to cool before charging in the furnace, the time-element entered as a detrimental factor in the development of the pipe or shrinkage-cavities, which gave an ingot-structure deficient in soundness. The interpretations from such material must be made with due allowances for the methods of manufacture, and must be given proper weight, as general facts, in subsequent arguments. The difficulties under which investigators labor are not easily surmounted in differentiating between reliable and unreliable data incident to variables of methods of manufacture, chemical composition of the alloys of steel, mediocre practice and that of the highest state of the art. Modern practice and large outputs in Bessemer steel have reversed the effects of the time-element-by cutting short the chemical reactions of the recarburizer and the elimination of

Jan 5, 1908

7253. Arkhangelsky, A. D. Geological Results of the General Magnetometric and Gravimetric Surveys of the U.S.S.R. (in Russian). Internat. Geol. Cong., Rep. of the 17th Sess., Moscow-Leningrad, 1937, vol. 1, Moscow, 1939, pp. 241-250. Geophysical methods have been used in the U.S.S.R. to study geological problems. Such is the case of the general magnetometric and gravimetric surveys made jointly by the Main Physical Observatory, Main Office of Geodesy and Cartography, Institute of Terrestrial Magnetism, and Main Office of Geophysical Prospecting. Some institutions supplied the data, others processed them. Geological interpretation was made by the author. (1) Regional magnetic anomalies in the plains of the U.S.S.R. are traceable to the folded substratum overlain by sedimentary rocks; these anomalies promise to yield data characterizing the substratum in respect to strike and depth. Anomalies in European U.S.S.R. suggest that the pre-Cambrian -substratum of the East European plateau consists of elements of different ages. In the most ancient of them, the main strike of the folding is almost latitudinal; in the younger ones, the folding is oriented in the meridian. (2) The Faye and Bouguer gravity anomalies are caused primarily by differences in the density of rocks composing the upper crust and by unknown processes producing changes of density at depth; these processes are not connected with isosiatic movements. The anomalies in the European and adjoining Asiatic U.S.S.R. promise to indicate the volume of the pre-Cambrian massif of the east-European plateau and to clarify the interrelations between the Ural, Tian-Shan, and Donetz Basin folding systems, as well as between the Dnieper-Donetz depression and the mid-European depression. - V. S.

Jan 1, 1944

By E. F. Koppe

The Upper Freeport coal in the Freeport and New Kensington quadrangles, Pennsylvania, varies from a bony streak to a thick coal deposit often exceeding ninety inches, the "Double" or "Thick Freeport". Distinctive basal partings, a central bone layer, and a canneloid top bench may be present. The appearance of a sandstone roof, sandstone rolls, and bony coal at the top of the main coal bench can be anticipated in thin Freeport areas when basal partings are absent. When the two basal partings are present, a shale roof is normal. These effects are correlated with the original topography upon which the coal was deposited. The original depositional high areas tend to coincide with present structural highs. Preliminary data indicate that coal quality, in part, is affected by the deposi-tional setting. In "high" areas, a tendency exists for the main coal bench to contain higher percentages of fusain and mineral matter. Within limits, some-what higher ash fusion temperatures appear to correlate with paleotopographic highs. As a result of these findings, critical examination of the paleotopography and related sediments is indicated in other areas and other coals. The Upper Freeport coal is quite variable both in thickness and composition in the Freeport and New Kensington quadrangles of Pennsylvania (Figure 1). The coal horizon in these quadrangles is marked either by a thin carbonaceous shale bed or by a single bed containing a variable number of partings (binders). The complex coal zone known locally as the "Double" or "Thick Freeport" contains the Upper Freeport Coal Bed at the base; but in addition, it has an overlying bone layer and an upper coal bed occasionally capped with a canneloid layer. The "Thick Freeport" often exceeds 90 inches in thickness, whereas the normal Upper Freeport coal usually varies between 34 and 50 inches.

Jan 1, 1961

By M. C. Leverett

Knowledge of the theory underlying the behavior of mixtures of fluids in reservoir rocks is essential to the proper solution of certain types of problems in petroleum production, but is as yet incompletely developed. The object of this paper is to show the application of well established thermody-namic and physical principles to these problems, and thus to assist in the development of the basic theory. For convenience the problems to be considered here may be divided into two groups: 1. Static problems, involving only the static balance between capillary forces and those due to the difference in densities of the fluids; i.e., gravitational forces. 2. Dynamic problems, involving analysis of the motion oi mixtures of immiscible fluids in porous media under the influence of forces due to gravity, capillarity, and an impressed external pressure differential. Capillary Equilbrium in Sands Under this heading the static type of problem will be discussed and the results of experimental investigations on the capillary properties of unconsolidated sands will be presented. Although the discussion of this section is, in a sense, prefatory to the treatment of problems of mixture flow, the concepts developed here have considerable intrinsic importance apart from their ap-plication to flow problems. For, it is reason-able to postulate that the reservoir fluids are, owing to their long existence in undis- turbed mutual contact prior to exploitation, in substantial equilibrium. It follows that their distribution in the reservoir at the time of tapping should be entirely predictable from the theory of capillary equi librium, provided certain experimentally measurable properties of the reservoir rock are known. Knowledge of the distribution of the several fluids in the reservoir is, ol course, helpful in the estimation of reserves and in other problems. It is to be emphasized that throughout the discussion of capillary statics it is assumed that the fluids are in equilibrium from the capillary standpoint. Thus, water, where it is referred to as being in a reservoir, will be understood to be interstitial water, present at the time of drilling the reservoir, commonly termed "connate" water. The theory developed here is perfectly general for any porous solid, whether a carefully prepared unconsolidated sand or a natural sandstone from an oil reservoir. At present, however, only problems involving clean, unconsolidated sands can be made to yield numerical solutions, since only such sands have been adequately investigated experimentally. Experimental evaluation of the pertinent properties 01 natural reservoir rocks will permit the extension of the numerical treatment to problems involving these materials. We shall now consider in some detail the static equilibrium of fluid mixtures in porous solids: that is, the manner in which the reservoir fluids are distributed vertically whell the Forces due to capillarity are just balanccd by those due to gravitation.

Jan 1, 1941

By M. C. Leverett

Knowledge of the theory underlying the behavior of mixtures of fluids in reservoir rocks is essential to the proper solution of certain types of problems in petroleum production, but is as yet incompletely developed. The object of this paper is to show the application of well established thermody-namic and physical principles to these problems, and thus to assist in the development of the basic theory. For convenience the problems to be considered here may be divided into two groups: 1. Static problems, involving only the static balance between capillary forces and those due to the difference in densities of the fluids; i.e., gravitational forces. 2. Dynamic problems, involving analysis of the motion oi mixtures of immiscible fluids in porous media under the influence of forces due to gravity, capillarity, and an impressed external pressure differential. Capillary Equilbrium in Sands Under this heading the static type of problem will be discussed and the results of experimental investigations on the capillary properties of unconsolidated sands will be presented. Although the discussion of this section is, in a sense, prefatory to the treatment of problems of mixture flow, the concepts developed here have considerable intrinsic importance apart from their ap-plication to flow problems. For, it is reason-able to postulate that the reservoir fluids are, owing to their long existence in undis- turbed mutual contact prior to exploitation, in substantial equilibrium. It follows that their distribution in the reservoir at the time of tapping should be entirely predictable from the theory of capillary equi librium, provided certain experimentally measurable properties of the reservoir rock are known. Knowledge of the distribution of the several fluids in the reservoir is, ol course, helpful in the estimation of reserves and in other problems. It is to be emphasized that throughout the discussion of capillary statics it is assumed that the fluids are in equilibrium from the capillary standpoint. Thus, water, where it is referred to as being in a reservoir, will be understood to be interstitial water, present at the time of drilling the reservoir, commonly termed "connate" water. The theory developed here is perfectly general for any porous solid, whether a carefully prepared unconsolidated sand or a natural sandstone from an oil reservoir. At present, however, only problems involving clean, unconsolidated sands can be made to yield numerical solutions, since only such sands have been adequately investigated experimentally. Experimental evaluation of the pertinent properties 01 natural reservoir rocks will permit the extension of the numerical treatment to problems involving these materials. We shall now consider in some detail the static equilibrium of fluid mixtures in porous solids: that is, the manner in which the reservoir fluids are distributed vertically whell the Forces due to capillarity are just balanccd by those due to gravitation.

Jan 1, 1941

By S Henderson

The Thames gold-silver deposits are part of the Hauraki goldfield, situated within the Miocene to Pliocene calc-alkaline Coromandel Volcanic Zone (CVZ). The Waitangi vein system is one of the mineralised ore shoots in the Thames district. The Thames gold deposits are characterised by shallow level epithermal vein mineralisation with phyllic to advanced argillic alteration assemblages and abundant sulphide minerals including pyrite, arsenopyrite, chalcopyrite, galena and sphalerite. Gold occurs as electrum in association with sulphide minerals. Microprobe analyses.of sphalerite grains from the Waitangi deposit mostly range from 0.8 to 1.5 mole % FeS, although one sample contains 9.5 mole % FeS. Arsenopyrite from Waitangi yields a range from 33.1 to 34.6 atomic As (%). There is no discernible correlation between the FeS content of sphalerite and gold grade in the Waitangi deposit suggesting that gold deposition is probably not controlled by changes in temperature and activity of sulphur aS2 that control the FeS content of sphalerite. The possible causes for gold deposition are thought to be boiling, mixing and changes in pH. Sulphur isotope analyses of mixed sphalerite-galena and sphalerite-galena-ehalcopyrite samples yield a narrow range of d34SCDT values (-1.0 to 0.9 ë;n=5), whereas late spongy pyrite gives unusually light sulphur isotope values (-16.7 to -27.9 ë; n=4). The sulphur isotopic values of base metal sulphides from Waitangi suggest that the sulphur was derived from a magmatic source. However, the source of light sulphur in the late pyrite grains is not known. Preliminary fluid inclusion+studies indicate homogenisation temperatures between 173¦ and 284¦C and salinities of 0.23.0 NaCI equiv. wt % (uncorrected for C02). Vein quartz at Waitangi yields d18OSMOW values from 6.8 to 12.7 ë (n=23). The calculated oxygen isotopic composition of ore fluids is between -2.1 to 3.8 ë at 250¦C and -0.1-5.8 ë at 300¦C. Oxygen isotope analyses have revealed significant variations in d18O values with elevation and gold grades. Zones of gold enrichment coincide with a zone of variable oxygen isotope values at the top of the vein system, where boiling and/or fluid mixing most likely occurred. Oxygen isotope values varying with gold grades within the Waitangi conduits suggest that d18O values may be useful in targeting bonanza grade gold mineralisation in epithermal vein systems.

Jan 1, 1993

By E de Villiers

Several methods exist by which the capacity of a dense media separation (DMS) plant can be improved: 1) Increase the feed rate in spite of efficiency 2) Replace with bigger equipment 3) Add whole new module 4) Replace total plant 5) Change over to four shift/ seven days per week roster 6) Replace with alternative process 7) Increase the availability and utilization Options 1 ? 6 have varying degrees of cost implications. The seventh option would seem to be the easiest. Normally it is also the function of the plant operating and maintenance team to maximize this. Usually higher operating and maintenance cost are associated with an increase in these parameters. A general principle that is applicable to plants and systems is that as the complexity increases, the total availability decreases. By simplifying the flow line it may be possible to reduce cost while at the same time increase the availability and utilization. The typical standard DMS flow line contains components that compensate for the variance in pump performance or for the inefficient recovery of ferrosilicon with additional equipment. Things have changed though: 1) Advanced electronic control and monitoring is possible 2) More efficient magnetic separators are available 3) New more user friendly densifiers are available ORIGINAL FLOW LINE In principle the process consists of four flow lines or streams 1) Ore flow ? the feed is divided into a waste and product stream by means of the separating vessel

Jan 1, 2006

The Morley Coal Measures (Upper Cretaceous) at Ohai Coalfield were deposited in an intermontane basin alluvial environment of entirely terrestrial aspect. Within this regional setting, three distinct types of depositional environment are recognised; these are: (i) a sand-dominated (South Saskatchewan type) braided river system characterized by channel-bed dunes and possibly compound bars; (ii) a well-drained floodplain environment frequently subject to crevasse-splay and overbank-flow sedimentation; and (iii) a poorly-drained, commonly peat-accumulating backswamp environment locally traversed by tributary drainage systems and occasionally inundated by crevasse splays and overbank flows. All major coal seams of the Morley Coal Measures originated within forest moors under predominantly telmatic (periodically inundated) conditions. The peat-forming vegetation comprised largely arborescent forms (dominantly conifers), in addition to pteridophytes and bryophytes. In-seam vertical variations in coal type indicate groundwater levels initially decreased and then increased during the lifetime of a particular peat swamp, possibly in response to a change in the migration direction of an adjacent fluvial system. The proposed depositional model for the Morley Coal Measures has the potential to be utilised during exploration programmes and mine development to impart greater objectivity to predictions concerning seam geometry and continuity, trends in coal type and quality, and likely roof and floor conditions.

Jan 1, 1985