Search Documents

By Sunil Jayasekera

This paper describes the results of a study carried out to examine the feasibility of electrolytic recovery of silver from cyanide leach liquor generated from a Western Australian silver mine tailings using a novel high mass transfer electrowinning cell. The proposed circuit involves heap leaching and electrowinning in a closed loop. The filter-press-like closed electrode arrangement of the cell allowed much improved mass transfer of metal ions to the cathode surface, making direct electrowinning of metals from dilute solutions feasible. The tests were conducted both in the laboratory and at large scale using a prototype with ~1.0 m2 cathode area. The results showed that the recovery of silver from as low as 250 mg L-1tenor was feasible. The silver deposit produced with the prototype cell was non-adherent and powdery and could be readily removed from the closed cell. A system was developed so that silver powder was discharged continuously during the run.

Jan 1, 2003

By R. V. Ramani, A. S. C. Owili-eger

The Methane Generator program is a part of the Internal Environ¬mental Sub-system of the Master Design Simulator (MDS). All the sub¬systems of the MDS are controlled and activated by the main program as required. The data requirements for the Methane Generator are supplied by the Geology and Reserves sub-system through common storage. Figure 6 shows the information flow between the Methane Generator and other systems of the MDS. It should be noted that the Methane Generator can also function independently as was described under model application. AREAS OF MISSING INFORMATION In any numerical analysis, the accuracy of the solution depends entirely upon the data available. In gas flow problems, parameters that constitute basic model input data are rock porosity, medium permeability, reservoir pressure and initial reservoir pressure dis¬tribution. Unfortunately, however, most of these characteristics are not available for a lot of coal seams. The need for actual field data cannot, therefore, be adequately emphasized here.

Jan 1, 1974

By J. B. Pautler, A. E. Gross, M. G. Strominger

The U.S. Bureau of Mines research on the use of cement as an agglomeration aid allowed precious metals heap leaching to become an economically viable method of precious metal recovery during the 1980's. However, many agglomerated ore bodies still exhibited poor heap/agglomerate strength. Precious metal recovery was often too slow or required prohibitively high levels of cement to be economically sound. Problems with heap ponding, blinding, and solution channeling and "wash-out" indicated that there was a need within the industry to improve on existing agglomeration technology. An in-depth research effort was undertaken to satisfy this need. Three years of research led to a patent on the use of vinyl addition polymers as effective agglomeration aids. A close working relationship between Brewer Gold and Nalco Chemical Company aided in the development of this program. This paper details the pilot test work, the full-scale evaluation at Brewer Gold Company, and conclusions.

Jan 1, 1990

By Klados. T.

MSC.Software assessed the performance of the drive end and non-drive end bearings on a ball mill using the finite element method. The assessment included the effect of mill and pedestal deformation on the performance of the bearings. Oil film thickness, oil pressure distribution and power requirement were of interest. A solution approach coupling a structural solver to a Reynolds equation solver was specifically developed for the project. Results showed that the deformation of the bearing surfaces had a significant influence on the performance of the bearings. For example, for the non-drive end bearing, the minimum oil film thickness computed for the deformable bearing surfaces was significantly lower than calculated for the non-deformable case. The results also showed that cavitation was likely in both the drive end and non-drive end bearings (severe negative pressures were obtained in both bearings). Other design variations were also assessed, e.g. a case with a modified radial clearance which improved the results.

Jan 1, 2006

By Lawson F

Pyrite concentrate and calcine from the Nanjing Lead-Zinc-Silver Mines, China, were leached with aqueous cyanide and thiourea solutions. More than half of the contained gold and silver was able to be extracted from the roaster calcines. The very fine dissemination of precious metal grains, high roasting temperature (850 - 900°C) and residual sulphur are believed responsible for the Iow extractions.A recovery of about 70 per cent for both silver and gold was able to be obtained with cyanide and with thiourea leachants when the pyrite was roasted in the laboratory at temperatures between 600 and 650°C.Thiourea, as an alternative leachant, has received much attention recently and a series of constant potential leaching tests was conducted.When the thiourea to formamidine disulphide mole ratio was about two, the precious metal extraction was greatest. In the Nanjing calcined material, this occurred at a potential of about 210 mV relative to a standard calomel electrode.

Jan 1, 1987

By J. Alton Burks, Robert R. Stein

This paper focuses on the noise exposure levels of miners employed on longwall production faces. Along with the increased production from longwall units has come the potential for greater noise exposures. Typical noise levels are given for the various noise sources that are present on modern longwall faces. Exposure times have typically increased since the introduction of longwall technology in this country. Representative exposure times and patterns are analyzed. Possible solutions are presented for generalized cases. Engineering controls developed by the Bureau of Mines are explained and their potential effectiveness is calculated for the cases presented. The role of hearing protectors in an overall hearing conservation program is also investigated. Recent research performed by the Bureau suggests that the actual performance level of muff -type protectors may be less than the manufacturers ratings under certain circumstances. The use of muff- type protectors is discussed and analyzed with respect to their use on longwall operations.

Jan 1, 1992

By L. S. Gourevitch, E. B. Kremer, A. Y. Fidlin, Y. M. Katsman, I. I. Blekhman

A new kinetic approach to simulation of fracture is given. The main object of the simulation is forecasting transformation of ore lumps size distribution in squeezing of ore layer between two planes. The approach rests on fundamental principles of energy and mass conservation and on new ideas about fracture physics connected with fractal geometry. On this base an integro-differen tial equation of layer crushing kinetics is formulated. This equation is similar to well-known kinetic equation of grinding, but here we use elastic energy density in place of time as an independent variable while selection function is considered by us to be dependent on this variable. Properties of the equation have been investigated by us and its analytical solution has been found. It allows to compute simultaneously both the evolution of the size distribution process of squeezing and force-displacement diagram. Results of theoretical calculations provide a good fit with experimental data.

Jan 1, 1995

It is desirable to have a model, or method, for major project development, which will enable flexible modelling of separation circuits. This ability improves the understanding of circuits and how they should be operated, especially in a design phase, where various options are evaluated and decisions are made on the required number of stages and configuration. This paper describes existing gravity separation circuit modelling theory and concepts, as defined by Holland-Batt1 (separation window, separation efficiency and proportionality of efficiency). The crux of the paperis the application of numerical analysis to fit raw separation data by means of a modified Bézier-Spline. The paper proposes an alternative to the theory developed by Holland-Batt that provides more flexibility in the modelling of separation stages and curves, which include S-shaped curves. The paper proposes a solution to the challenge of continuously extrapolating data, and the first difficulty normally encountered, which is the fitting of an appropriate empirical formula to raw data.

Jan 1, 2007

By R. K. Mehta, K. N. Han, P. B. Queneau, V. Dieudonne

A study based on a statistically designed sets of experiments (central composite design) was conducted to determine the optimum conditions for leaching a subbituminous coal (7.0 % ash) from the middle Wyodak seam in mild sulfuric acid solutions. The statistical analysis was conducted with the ash content and ash removal as the dependent variables and with the coal loading, acid concentration, ferric ion concentration, and temperature as the independent variables. Treatment of the experimental data via a simple genetic algorithm (GA) revealed that acid concentration and temperature are the two most critical variables. Unlike the case with bituminous coal, the ferric ions addition shows no beneficial effect. The optimum "macro response" predicted by GA was verified experimentally; the ash content was reduced to 2.7%, which is close to the value predicted by GA. The ash content was further reduced to 1.7% in a two-stage leaching process devised by incorporating the optimization results with that of leaching kinetic studies.

Jan 1, 1993

By Anita E. Lam

The thiosulfate leaching of gold generally requires the presence of a catalyst such as cupric tetraammine, Cu(NH3)42+, to obtain reasonable leaching rates and gold extractions. Unfortunately, this same catalyst that accelerates gold leaching also tends to accelerate thiosulfate oxidation to tetrathionate and other species. It is therefore imperative that a detailed understanding of the role of this catalyst and the factors affecting it is obtained. It is equally important for plant application that a method of assessing the catalyst be developed. In this work the role of the cupric tetraammine catalyst was studied using geochemical modeling for speciation prediction, thiosulfate leaching of gold ores, and chemical analyses of resulting leach solutions. It was found that the variables of pH, temperature, and the concentrations of ammonia, thiosulfate, and total copper all work in concert to affect the concentration of the cupric tetraammine species. It was also found that the presence of sufficient thiosulfate and cupric tetraammine was critical to the success of the leach.

Jan 1, 2003

By S. J. Kohut

Until recently SX-EW technology has only been used to produce conventional cathode for the cyclical commodity marketplace. Unlike electrorefining, SX-EW lends itself to the integration with the downstream manufacturing technologies for direct mine site production of value added products. The integration of SX-EW and downstream manufacturing results in the elimination of redundant process steps, the cost savings, and the access to value added product markets which can buffer the producer from swings in the cathode market. SX-EW production of copper powder and powder-based products has been demonstrated at the pilot plant level. The SX-EW process has been successfully redesigned to meet the more specific demands of engineered products. Challenges include the solution purity, the cell ventilation, the high current density operation and the product handling. Successful demonstration of mine site production of value added SX- EW products opens up new non-commodity marketplaces to the mining industry.

Jan 1, 1999

By B. J. Arnold, C. D. Harrison, R. A. Lohnes

More than 544 Mt (600 million st) of coal are handled annually for use by this country's coal fired power plants. Coal is transported in various ways: overland conveyors, railcars, trucks and barges. It can travel short distances or thousands of miles, picking up moisture, freezing or drying. When the coal is received at the power plant, environmental problems with fugitive dust and further handling problems can arise. To ensure that power plant availability is not jeopardized by coal handling problems, the Electric Power Research Institute's (EPRI) Coal Quality Development Center (CQDC) developed a research program aimed at addressing utility coal handling problems. The program has identified key areas, and is investigating the cost and cause of coal handling problems as well as the solutions to these problems. The ultimate goal of the program is to develop a "handleability index" that utilities can use in their coal specifications or hardware for a utility's sampling system to predict handleability and determine if a coal shipment should be accepted.

Jan 1, 1993

By J. M. Stuve

This Bureau of Mines investigation measured the low-temperature heat capacities of FeOC1(c) and FeC13(c) in the temperature ranges of 6 to 305 K and 4.6 to 300 K, respectively. The standard entropies (S°, 298.15 K) of FeOCl(c) and FeC13(c) were derived as 19.73±0.03 cal/deg-mole and 35.33±0.07 cal/deg-mole. A large lambda transition was observed in the heat capacity of FeC13(c) at 8.4 K. The standard enthalpy of formation (?H°f, 298.15 K) of FeOC1(c) was determined to be -98.23±0.22 kcal/mole by HC1 solution calorimetry. High-temperature enthalpy measurements (H-H298.15) of FeOC1(c) were determined to 700 K by precision drop calorimetry. Standard thermodynamic formation data and related functions were tabulated at various temperatures for FeOC1(c) and FeC13(c).

Jan 1, 1980

The negative charges on diaphragms of quartz, tungstic oxides, stannic acid, acid dyestuffs, soaps, and glass have for a number of years been explained on the basis of chemical equilibria-a hydrogen ion or light metal ion passes into solution leaving the solid complex ion negatively charged. While there are a number of observations which indicate a proportionality between the ( potential and the streaming potential it should be recognized that all the experimental evidence thus far presented shows that if hydrogen ion concentration is kept at a constant value, electrokinetic phenomena are influenced by salts. The multivalent ions exert the greatest effect on the reduction of osmotic flow. In the interpretation of all electrokinetic data the assumption is made that the potential of the solid remains constant. That this is not true is evidenced by the values of ( potential for quartz in contact with conductivity water as reported by the several investigators and by the authors of this paper.

Sep 1, 1956

By E. S. Machlin, Morris Cohen

GRENINGER and Troiano' were the first to establish the fact that the habit planes of mar-tensitic products are usually planes of high indices. In steels containing 0.55 to 1.4 pct C, the habit plane indices are {225}A.* In steels with more than 1.5 pct C and in Fe-Ni alloys, the indices are {259In. The presence of both habits in certain alloy steels has been reported recently." Several investigators"-" have subsequently attempted to provide an understanding of these complex habit relations. Bowles'6 work is the most recent and the most successful. Like Greninger and Troiano, Bowles concluded that the transformation occurs in two steps, the first, a strain (or displacement) that is homogeneous throughout the volume of the martensitic plate, while the second is a strain that is homogeneous only within relatively small portions of the martensitic plate. The first strain yields the measured tilt of the specimen surface, but does not produce the final martensitic structure. This and the correct lattice orientations are achieved by the second strain. Bowles also reasoned that each strain could be described by the motion of a plane of no rotation and no distortion (hereinafter called the invariant plane) in a direction not necessarily contained in the plane.** In applying these considerations to steels with {225}a habits, Bowles found that the habit plane coincided with the invariant plane of the first strain, a result which signified that the atoms move along certain paths during the transformation. Whether this correlation results from the existence of some sort of a plate nucleus6 lying along the invariant plane of the first strain, or whether the invariant plane primarily defines the preferred directions of propagation of the first strain, will be discussed in a later section. There are two obstacles to the general acceptance of Bowles' treatment: 1—it has not been shown that elements of his double-strain analysis are unique, and 2—it is not known whether his treatment applies to transformations yielding the {2591A habit. Unless these two questions are resolved, the correlation between the habit and invariant planes in the {225}A systems might be regarded as coincidental. Experimental Procedure Using a 70 pct Fe-30 pct Ni alloy as an example of a {2591A habit system, preliminary attempts were made to obtain a double-strain solution based on a Nishiyamax** set of orientation relations and on a Greninger-Troianot set, adopting the stereographic technique described by Bowles" who used the Kurd-jumow-Sachstt set in connection with the {225}A habit. These attempts were unsuccessful because the method is essentially one of trial and error and requires either exceedingly good luck or a prior knowledge of the results being sought. Consequently it was decided to measure independently the strain associated with the formation of a martensitic plate as well as the habit-plane indices of the particular plate. By means of matrix algebra, the measured strain was applied to the austenite lattice, whose orientation with respect to the strain was determined, in order to ascertain whether the resultant structure would have the lattice of martensite. This was not found to be the case, and hence it was assumed that the measured strain was the first of two Bowles-type strains, characterized by the motion of an invariant plane. A solution of this displacement was obtained in terms of the invariant-plane indices and the direction of motion of the atoms. Then the second strain

Jan 1, 1952

By Mehmet Mesutoglu, Ihsan Ozkan

This study investigates the feasibility of rock bolting support in an underground coal mine gallery with a thick coal seam. The Ömerler underground coal mine working area, owned by West Lignite Enterprise of Turkish Coal Enterprises, was selected for this purpose. Longwall top coal caving is implemented as the production method in the Ömerler underground coal mine. Field and laboratory studies were conducted to determine rock mass and rock material properties, followed by experimental, empirical and numerical analyses based on the acquired data. The obtained design results were evaluated using a resin-grouted rebar rock bolting (RBR) system and steel arch support (SAS) pilot application areas. The numerical modeling results conducted using the fast Lagrangian analysis of the Continua 3D (FLAC 3D v6.0) program indicated less displacement and secondary stress change in the RBR-supported zone compared to the SAS-supported zone. In situ measurements also demonstrated that RBR provided more successful support to the roof during coal production activities. The findings suggest that RBR is a more effective solution when evaluating the feasibility of rock bolting support systems in underground galleries with thick coal seams at the Ömerler Mine. This study emphasizes the importance of more sustainable and safe support systems to enhance operational efficiency in the coal mining industry.

Mar 1, 2025

By H. Marquis

The present paper consists of a survey of the literature on the problems of abrasion and wear of metals and materials by suspended matter. This problem is a very general one in industry, and is especially notice-able in the operation of cyclones and other types of dust collectors. The problem of abrasive dust in corrosive gas environments, such as commonly encountered in metallurgical industries, is particularly severe. Very little work has been done in the study of this type of abrasive wear, especially at high temperatures. However, a general review is presented here of all the work published on related subjects, such as that involving sand erosion in turbines and water wheels and the effect of temperature on friction wear. Topics in this paper include: blasting wear by sand, quartz, limestone, silicon carbide and other refractory particles; methods of investigation; effects of velocity, temperature and *Canadian Armament Research and Development Establishment, Valcarter, P.Q. angle of attack; correlation between indentation hardness, scratch hard-ness and resistance to abrasion; the effect of protective coatings; resistance of various metals; etc.

Jan 1, 1962

By Olofsson O, Durance M-V, Villeneuve J

Modelling of the Sala Agitated Mill (SAM) using a simplified solution to the population balance approach has been carried out. The rate of breakage is modified by the mill power, providing predictions of the resulting product size distribution for different grinding conditions and mill sizes. The power of the mill is estimated by a physically derived function, using an assumption that the mill power consumption mainly arises from the ball to ball friction within the mill. The grinding efficiency, depending on the media ball size and pulp density is approximated in the model. Experimental work on grinding a complex sulphide ore using a pilot scale SAM 7.5 has been carried out. Good agreement has been found between the data from the test campaign and the simulated values. The model has also been validated with experimental data from a pilot grinding of calcium carbonate and from an industrial mill. The model is included in the USIM PAC simulation software.

Jan 1, 1995

By Wilbert J. Huff, Raymond H. Moore

"Black powder is employed widely in peace and war. Its properties are therefore of considerable interest to many. The Bureau of Mines frequently is asked to furnish information on its use and safe handling in the mining and mineral industries in times of peace and is now engaged in studies of its application to the arts of war.Black powder has been the agent in many accidents - some very disastrous - and its handling and use are deemed very hazardous. The belief is widespread that the hazards are due principally to the ease with which the powder is ignited by a hot spark or flame in contradistinction to high explosives; these usually are ignited only with difficulty, and some burn incompl0tely and to a certain extent are self-extinguishing. Primary precautions, .therefore, should be taken to prevent the access of heat, spark, and flame.In black powder manufacturing operations a frequent source of disaster is the initiation of fires and explosions in the wheel mills in which the sulfur, charcoal, and nitrate are incorporated. Long experience has indicated that the wheel mill probably will fire if the powder is not kept moist enough; manufacturing supervision calls for the maintenance of a minimum moisture content, at least during the milling. Accidents occur elsewhere in the manufacturing line, and in an endeavor to minimize these, particularly those happening in corning mills, one of the writers suggested many years ago that a suitable humidity be maintained in other operations in the hope that it would serve protectively as in the wheel mill. The experience of one company for many years with this practice was favorable. It seemed desirable therefore, to explore the question experimentally."

Nov 1, 1944

The sulphide ore occurring in the North Mine at Broken Hill is of a complex nature, consisting of an intimate mixture of argentiferous galena, marmatite (zinc-iron sulphide), and gangue minerals. A typical analysis of the ore is:Lead 15.2%Zinc 12.0%Iron 5.3%Manganese 0.8%Copper 0.1%Alumina 0.3%Lime 0.9%Sulphur 11.1%Insoluble 53.8%Carbon dioxide 0.3%Undetermined 0.2%Silver 9 oz. per tonTotal 100.0%The metallurgical practice for the recovery of the lead concentrate and zinc concentrate from the crude ore is briefly described in the following pages.(1) COARSE CRUSHING AND FINE GRINDING OF THE CRUDE OREThe crude ore from the mine, containing lumps to the size of, roughly, 10 in. x 8 in., is tipped over grizzlies with the bars spaced 3 in. apart; the oversize gravitating to a...

Jan 1, 1933