Search Documents

By R. F. Domagala, D. J. McPherson

Iodide zirconium was combined with calculated amounts of ZrO2 or master alloys and arc-melted. Annealing treatments were carried out at 21 temperature levels. Metallographic examination of the heat treated specimens permitted construction of the binary phase diagram from zirconium to ZrO2. Oxygen additions to zirconium raise the transformation temperature as well as the melting point. Features of the diagram include the peritectic formation of beta, the formation of alpha directly from the melt, an intermediate phase ZrOB with a' range of homogeneity, and a eutectic between alpha and Zr02. PHASE relationships in the Zr-0 system were determined in the range 0 to 66. 7 atomic pct 0 (ZrO,). Arc-melted alloys were annealed at temperature levels between 600" and 2000°C. Determination of the phase boundaries was accomplished by metallographic evaluation of specimens quenched from the various temperatures. Incipient melting techniques were used to determine solidus curves, and X-ray diffraction work was employed to study the lattice parameters of the a solid solution and the phase ZrO,. Experimental Procedures Westinghouse "Grade 1" iodide zirconium crystal bar (approximately 99.8 pct pure) was employed for the investigation. This material is substantially free of the impurity inclusions characteristic of most zirconium metal. Previous work has shown it to be the most satisfactory grade for phase diagram studies. The zirconium crystal bar, as-received, was coated with corrosion product from autoclave tests by which its grade designation is determined. The bars were sand blasted lightly, pickled for 1 min in a 20 pct HN0,-5 pct HF aqueous solution, rinsed in water and acetone, and dried. The bars were rolled to about 1/32 in. strip, cut into 10 in. lengths, and pickled again. The material was sheared to approximately Y4 in. squares, cleaned with acetone, and stored for use. Two pounds of specially prepared "chemically pure," and 100 grams of spectrographic grade ZrO, were obtained for the preparation of alloys. The "Specpure" ZrO, was obtained from Johnson, Mat-they Co.. Ltd.. and Titanium Alloy Manufacturing Div. of National Lead Co. supplied the other grade of oxide. The "chemically pure" material (henceforth referred to as C.P. ZrO,) was used for the preparation of all alloys employed in the determination of phase relationships. A limited number of alloys were prepared with the "Specpure" oxide to recheck certain phase boundaries. Analyses of the two grades of oxide are given in Table I. The C.P. ZrOI was received in powder form, not suitable for arc melting. Therefore, this material was compressed to wafers 1 in. in diameter and about Vn in. thick. These were segmented and stored for use. The "Specpure" material, in the form of small granules, was suitable for use in the as-received condition. A nonconsumable electrode arc-melting furnace was used to prepare alloys. A water-cooled copper crucible and tungsten-tipped electrode were employed. The material was placed in the crucible and rapidly melted under a protective atmosphere of helium gas by striking the arc on a tungsten stud and directing it upon the charge material. Details of operation, including drawings of this type furnace, have been published.'

Jan 1, 1955

By C Xu, B Li

Multi-sensor fusion visual perception technology significantly enhances visual perception capabilities in complex and harsh environments by combining visual data from different sensors. This technology is especially useful for scenarios where traditional single visible light sensors, such as standard cameras, struggle due to poor lighting, adverse visual conditions, or other visual obstructions. In environments with low light, smoke, or dust, the performance of conventional visible light sensors degrades, limiting their application. By integrating data from various sensors like radar, infrared thermal imaging, and others, multi-sensor fusion technology provides a more comprehensive and complementary visual solution. This fusion not only enhances the robustness of visual systems but also greatly expands their potential applications in fields like visual surveillance. In recent years, deep learning methods have become the mainstream technology for addressing multi-sensor fusion issues, demonstrating significant advantages in adaptive feature selection compared to traditional machine learning methods. However, deep learning-based multi-sensor fusion algorithms still face several challenges. The design of network structures is often redundant, lacking effective screening of useful components within multimodal information. Mainstream fusion algorithms focus excessively on improving display effects without adequately considering the needs of downstream applications and tasks. Existing fusion perception algorithms are generally designed for open visual scenes and lack targeted design for complex visual degradation factors present in tunnel environments of mines. Current deep learning methods for designing multi-sensor fusion networks heavily rely on manual experience to create fusion modules. This reliance increases the complexity of network design and can lead to redundancy. Redundant network modules are difficult to identify in end-to-end learning tasks at this stage, significantly slowing down network inference and potentially interfering with the output of fusion perception. Additionally, training these fusion modules typically requires large amounts of well-annotated multimodal data, further increasing implementation difficulty and cost. For instance, the fusion network design proposed by Li and Wu (2018) focuses on extracting multimodal fusion features, while Zhao et al (2020) introduced a feature decomposition mechanism in the feature fusion and extraction modules. Researchers like Zhang and Ma (2021), Xu et al (2020), and Liu et al (2017) have attempted to improve network structures through dense cascades and the introduction of residual connections. Although these methods have improved the handling of multimodal information to some extent, they still face limitations in distinguishing between useful and redundant information, with redundancy persisting in network designs. Ideally, the design of fusion networks should be more intelligent, guiding network structure design heuristically based on the importance of different modal information for the current task. This would reduce information redundancy and network weights, requiring the development of new algorithms or frameworks capable of automatically identifying and optimising fusion strategies, thereby reducing dependence on manual experience while improving fusion efficiency and network performance. Current deep learning designs for multi-sensor fusion algorithms often overlook the

Sep 1, 2024

By Rudy Rogers

Gas hydrates have unique properties of storing selective gases. As much as 180 volumes of gas (standard conditions) per volume of hydrates may be stored. Recognizing the need for natural gas storage near electrical power plants for peak load use, DOE funded our laboratory to investigate gas hydrates as an economically viable storage means. Our developed process forms hydrates and self-packs the hydrates by only maintaining the gas pressure above a surfactant/water solution while hydrates form and self-pack. The laboratory process was scaled-up and demonstrated storage of 5300 scf of natural gas in hydrates. Subsequent to the demonstration, we discovered preparation procedures whereby laboratory gas hydrates could be stored at 1-atm with less than 1% decomposition over multiple days. The paper will discuss how these two advancements offer potential ways to recover vent gases as well as released hydrate gases from the seafloor. Keywords: gas hydrates, methane storage, surfactants, hydrate stability

Jan 1, 2008

By H. Rosenthal, A. L. Jamieson

THE action of mercury on stressed brass to produce cracks was known before Moore, Beckinsale and Mallinson1 showed that actual season cracking did not occur spontaneously but could be induced by ammonia. These investigators studied other substances, including diphenylamine, without finding that anything other than ammonia could cause season cracking. Grimston2 reported season cracking in cartridge cases stored in wooden boxes wetted with dilute sulphuric acid pickling solution. Season cracking associated with sulphur dioxide, water vapor and air has been reported by Johnston,3 although he reported that trimethylamine and pyridine did not cause cracking. Jevons4 has ascribed season cracking of brass in certain instances to trimethylamine, "aldehyde amine," "ketone amine" and pyridine, but no experimental work was done evidently to prove this definitely. Pyridine was investigated by Morris,' who found it to have considerable cracking power. In the present investigation, the object was a qualitative evaluation of a number of representative amines with respect to their ability to cause season cracking. Thus it was desired only that an appreciable vapor pressure of each amine be obtained in order to make the test as severe as possible, without attempting to test equivalent concentrations for comparative purposes. METHODS Specimens Two types of specimen were used: I. Unannealed 70-30 brass cups formed from 0.040-in. thick sheet. Height of cup was 1 3/8 in. and diameter was 1 7/8 inches. 2. First draw pieces of caliber .50 cartridge cases in the unannealed condition (70-30 brass). The cups were representative of a thin wall and thin base specimen, whereas the draw pieces have a thick base (1/4 in.) and a thick wall (approximately 3/32 in.). Both types of specimens contained high residual stress and cracked in less than one minute in a solution of I per cent mercurous nitrate and I per cent nitric acid provided that this was preceded by a 30-sec. pickle in 40 per cent nitric acid. Specimens were prepared as follows: (I) degreased in trichlorethylene, (2) rinsed in H20, (3) pickled 5 min. in 10 per cent by volume H2SO4 (1.84 sp. gr.), (4) rinsed in H2O, and (5) dried. Amines Tested In selecting the amines, representatives of the three series of amines and one series of substituted amines were chosen. The aliphatic series was represented by the methyl and ethyl primary, secondary and tertiary amines. These are the simplest aliphatic amines. For the aromatic series, the phenyl primary, secondary and tertiary amines were selected as being the simplest. The heterocyclic series was represented by pyridine, which is a simple heterocyclic base (tertiary amine).

Jan 1, 1944

By R. Van Deventer

The BIOX® process was developed for the biological pre-treatment of refractory gold ores and concentrates ahead of conventional cyanide leach gold recovery. Rights to the process are currently with BIOMIN Technologies SA, a subsidiary of Gold Fields Limited. There are currently eight operating installations worldwide employing the process on a commercial scale. EKATO is a company specializing in developing new or optimizing existing mixing applications. EKATO has acquired a vast amount of expertise in agitation over its 75 year history. In a joint research project the reactors of the BIOX® process were characterized from the aspect of their mixing performance. BIOMIN is constantly testing new mixing solutions and reviewing potential vendors to increase the efficiency of the BIOX® process. EKATO?s intention was to qualify as an approved vendor for supplying agitation equipment to the BIOX® process. A two step approach was planned: In phase one of the project EKATO would develop an alternative agitation solution to the established option, exhibiting at least similar performance levels. In phase two potential possibilities to improve the overall design would be developed. This paper focuses on phase one and addresses the systematic approach applied by EKATO in characterizing the mixing processes. Mixing tasks were assessed individually applying basic theory and scale-up and -down rules to the individual tasks. Testing with model systems was done at the EKATO technology center in Schopfheim, Germany, on scales of 50 liters and 1 m³. The results showed that the ISOJET-B impeller design showed promising performance under BIOX® reactor conditions. Scale-up with the ISOJET-B was done in order to apply it in the 21 m³ live volume test reactor at Fairview mine in South Africa. At Fairview tests were performed using model systems and eventually under real plant conditions with BIOX® slurries. The results were a success and confirmed that the scale-up factors determined during the testing at EKATO?s technology center could be substantiated in the ?model scale? 25 m³ reactor. Testing under the actual process conditions showed that all design parameters were within the desired range to be considered an excellent leaching performance. This successful joint development shows the importance of a close cooperation of technology licensors or end-users and equipment suppliers. It is vital for understanding all factors influencing the mixing performance of processes. Exercises such as this will provide equipment suppliers and plant operators more confidence in managing further scale ups at ever larger engineered plants.

Jan 1, 2009

By George B. Clark

Many basic engineering principles of all four phases of mining operations, namely, prospecting, exploration, development, and exploitation, can be analyzed better in terms of quantitative geology. Geological data from both field and laboratory will also complement scientific methods now being developed. THE geological data emphasized so successfully in prospecting for new deposits, that is, structural controls, strength of solutions, and type of mineralization, are basically those required for successful exploitation. In the mining of newly discovered deposits the most economical methods should be employed as early as possible to keep the overall cost per unit produced at a minimum and to permit maximum extraction of valuable minerals. A crucial question is: How can geological data be translated into useful quantitative results which will aid in achieving this end? H. E. McKinistry' has suggested that a solution may be reached in one of two ways: 1—the usual approach, use of judgment based on experience; or 2—mathematical calculations and tests on models, both subject to certain limitations. He also suggests that in addition to better use of geology more case data and theoretical data are needed on which to base sound judgment. Further research, therefore, is necessary. Perhaps in this field the emphasis should be on more specialization in mining methods and ground movement by men with thorough training in physics, engineering, geology, and underground mining. These specialists would be equipped to point out the most economical and scientific methods of exploitation. Selection of a stoping method is governed by the amount and type of support a deposit will require in the process of being mined, or by the possibility of employing the structure of the deposit to advantage in mining the ore by a caving method. In addition to these factors there are others which almost invariably influence the choice of an economical method of mining:' 1—strength of ore and wall rocks; 2—shape, horizontal area, volume, and regularity of the boundaries of the orebody, and thickness, dip and/or pitch of the deposit and individual ore shoots; 3—grade, distribution of minerals, and continuity of the ore within the boundaries of the deposit; 4—depth below surface and nature of the capping or overburden: and 5—position of the de- posit relative to surface improvements, drainage, and other mine openings. In the final analysis it is usually necessary to disregard the less important of these factors to satisfy the requirements of the more important. Because of the variation of geological conditions throughout and surrounding the deposit, no mining method will be everywhere ideally applicable to the conditions encountered in one ore deposit. The immediate problem is to interpret the above physical characteristics of deposits in terms of geological characteristics. Very few quantitative geological data are available on the factors related to a choice of mining methods. However, there are many descriptive data in mining and geological literature which collectively show how important an effect details of geology have upon all phases of mining operations. The following categories of basic mining methods were investigated to establish the geological factors that have affected their successful application: 1— open stopes with pillars; 2—sublevel stoping; 3— shrinkage stoping; 4—cut-and-fill stoping; 5— square-set mining; 6—top slicing and sublevel caving; and 7—block caving. It should be noted that the first five of these methods are listed in the order of increasing support requirements. Mines were selected as examples only where geological descriptions were complete enough to warrant their use. A study of the geological factors involved in mining operations led to a choice of the following classifications, employed in Table I: 1—structural type of orebody; 2—dimensions (geometry); 3— country rock (type); 4—faulting, folding, and fracturing; 5—alteration of ore and rock; 6—type of mineralization; and 7—geological factors determining mining method (summary). Of these factors only one yielded results that can be defined from available data in a quantitative manner, i.e., dimensions of the deposit. These are the most reliable guides that can be used in selection of suitable mining methods. They are, in general, the properties of geologic structure most difficult to evaluate by studies of models, pho-toelastic studies, and other laboratory methods, all of which are at present more limited in their applications than the geologic method. Application of geology has proved a reliable guide in other phases

Jan 1, 1955

By L. D. Wooddy, Robert Moscrip

The simultaneous solution of the volumerric balance and the unsteady-state equation has been used for several years to make performance calculations for combination drive reservoirs. This method makes possible the calculation of volumetric changes of fluids in the gas cap, oil zone, and aquifer which occur as a result of withdrawals and reservoir pressure changes. It does not provide a means for the determination of reservoir fluid distribution changes corresponding to these vollrmetric changes. A knowledge of the fluid saturation distribution in the reservoir at various stages of depletion is important for the determination of the efficiency of gas and water as oil-displacement media and, therefore, for the reliable predicrion of ultimate oil recovery. To provide this knowledge, the displacement equations are solved simultaneously with the volumetric balance and unsteady-state equations. The described calculation procedure has been used satisfactorily to analyze the past performance and to predict the future behavior of combination drive reservoirs under both primary and pressure-maintenance operations. INTRODUCTION The three basic mechanisms by which oil is displaced from a reservoir are: (1) dissolved gas drive—the displacement of oil by the expansion of liberated solution gas, (2) water drive—the displacement of oil by water which enters the oil zone from the aquifer, and (3) gas cap drive—the displacement of oil by gas which ex- pands into the oil zone from the gas cap. The action of gravitational forces may be effective in increasing the efficiency of the basic drive mechanisms. Gravitational forces favor the segregation both of gas and oil and of oil and water, thus tending to shorten the transition zone between oil and displacing fluids. Most reservoirs produce under the influence of a combination of these drives and are designated "combination drive reservoirs". Fig. 1 is a cross section of a typical combination drive reservoir. A calculation procedure for analyzing the performance of combination drive reservoirs has been developed by combining the displacement equations' with the volumetric balance equation' and the unsteady-state equations. The pressure-production performance and the positions of the gas-oil and oil-water contacts are calculated for several stages of reservoir depletion by solving these equations simultaneously, thus affording a basis for: 1. Determining instantaneous and ultimate oil, gas, and water production under various operating conditions. 2. 'Establishing a maximum efficient rate of production, 3. Determining the advantages of pressure maintenance and unitization, and 4. Designing surface installations necessary for primarv and pressure-maintenance operations. DEFINITIONS The calculation procedure for combination drive res-

Jan 1, 1957

By P. Hazebroek, C. S. Mathews, E. E. Allen, H. C. Lefkovits

A rigorous study was made of the behavior of reservoirs composed of horizontal layers, unconnected except at the well and filled with a compressible fluid. The report is presented in two parts. Part I deals with the practical implications of the results obtained; Part 11 contains the mathematical derivation of the solution. The main portion of Part I is concerned with application of the results to reservoirs composed of two layers. Relative rates of depletion of the layers are studied, and it is shown that differential depletion between layers exists in the transient stage of the reservoir, which generally is of an order of magnitude longer than the transient stage in a single-layer reservoir. In the transient stage, the more permeable layer is depleted faster than the less permeable. However, the reservoir approaches a steady-state situation where both layers contribute equally to production. Theoretical build-up curves from such reservoirs are presented, and the influence of a skin effect and flow into casing and tubing are also evaluated. The build-up curves are predicted to have, first, the familiar logarithmic straight-line section and, subsequently, a rising and flattened section. The results found are compared with an extension of an approximate theory, and it is found that this simplified theory is applicable over most of the life of the reservoir. Extensions to reservoirs containing more than two layers are indicated, and examples of the performance and build-up curves for three-layered reservoirs are presented. The theoretical results on build-up curves were applied to field examples of such reservoirs, and satisfactory results were obtained. From the build-up curve, the pemeability-thickness product, the wellbore damage and the static pressure are obtained. However, it apparently is not possible to determine the properties of the individual layers from the combined build-up curve. A large number of reservoirs have been found where the producing formation is composed of two or more layers of differing physical characteristics, such as permeability and porosity, and where also the thicknesses of the layers differ. Since in general a differential depletion should exist between the layers of such reservoirs, it would be advantageous to know the amount of the differential depletion under a given production history. It also would be valuable to know the pressure behavior, because it could be undesirable to produce a reservoir in such a manner that the pressure in one of the layers would have fallen below the bubble point of the oil at a time when another layer might still be virtually undepleted. The determination of static pressures in shut-in wells with slow build-up is another feature of importance in layered reservoirs. If the behavior of the reservoir differs appreciably from the predicted behavior of a single-layer reservoir, the type of analysis for build-up curves suggested for single-layer reservoirs is not applicable. Several authors have treated the problem of finding the pressure and production characteristics of multilayer reservoirs. Horner treated the problem of n layers in an infinite field, the layers being connected only at the well. Tempelaar-Lietz2 has presented an approximate treatment of the characteristics of a bounded reservoir composed of two layers of different permeabilities and equal thicknesses. Homer gave no information on differential depletion between layers, and the treatment of Tempelaar-Lietz was not applicable for prediction of pressure build-up behavior. In addition, it was thought that a more rigorous treatment than the one by Tempelaar-Lietz would be valuable in determining the range of validity of this solution. The present study, therefore, was made of a bounded reservoir composed of two or more layers,

By R. J. Pruett

The Georgia kaolin district is the world’s largest producer of kaolin. Georgia production tripled from 2.87 Mt (3.17 million st) in 1968 to8.35 Mt (9.2 million st) in 1998. Development of the Georgia kaolin industry can be traced to the identification of the mineral resource, the adoption of innovative process technologies and the creation of markets for kaolin. Georgia kaolin is an abundant and high-quality resource that shows a range of advantageous properties. Technical developments in wet processing, delamination and calcination allowed production of high-value products. The use of kaolin pigments in the paper industry provided a market that absorbed the rapid growth in kaolin production.

Jan 1, 2000

By A. J. Griest, P. D. Frost, J. R. Doig

During the past 5 years, research directed toward the development of titanium alloys having improved strength-ductility relationships and heat treatability has been carried out at Battelle for the U. S. Air Force.1"3 In the course of this work, a method of heat treating ß-stabilized titanium alloys was developed which produced a wide range of useful properties.4 The heat treatment consisted of two steps: a) solution treating at temperatures in the a-ß phase region, and b) overaging at a lower temperature in the range 800°to 1100°F. Corollary to the alloy development work, research was conducted on the mechanism of the heat-treatment reaction. The investigations of Frost and co-workers on isothermal transformation in Ti-Cr5 and Ti-Mn8 alloys disclosed the existence of the transition phase, w, during the course of the decomposition of metastable ß phase. Subsequent work at Battelle7,8 'and at Case Institute by Brotzen and co-workerss further clarified the nature of the decomposition process. Beta decomposition was found to proceed by the following series of reactions: 1 2 3 4 a + Ti, My (in eutectoid systems). ßo, ßr, and ßU refer to ß phase of original, enriched, and ultimate alloy contents, respectively. Omega is a transition phase having a complex structure. 10-13 Step 4, of course, occurs only in ß-eutectoid systems. This paper presents data correlating transformation behavior with mechanical properties for the following alloys: Ti-8Mn, Ti-8Mn-2A1, Ti-4Mn-4A1, Ti-6Al-4V, and Ti-4Fe. The isothermal decomposition of ß in titanium-manganese alloys of similar composition has been investigated by Frost and coworkers8 and the effect of various annealing treatments on alloys in this system has been studied by Holden, Ogden, and Jaffee.14 The compositions Ti-8Mn-2Al, Ti-4Mn-4A1, and Ti-6A1-4V, were studied in the present work in an effort to define more clearly the effect of aluminum on the response to solution and aging treatments. Ogden, Holden, and Jaffee15 have invesitgated the effect of aluminum on the response of a similar alloy (Ti-8.8Mn-2.46A1) to annealing treatments, and Luini and Lee16 have made an exploratory investigation of the heat-treatability of the Ti-4Mn-4Al alloy. The Ti-4Fe alloy was studied as an example of a moderate1y active eutectoid system. Holden, Ogden, and Jaffee 17 have studied Ti-Fe alloys and have presented some hardness data for aging at 400°C for alloys of Ti-2.56, 5.01, and 7.35 iron after quenching from the a-ß field (750°C). EXPERIMENTAL PROCEDURES The experimental procedures generally used in the precipitation-hardening study are outlined in the following sections. Departures from these techniques are noted in the discussions of the individual alloys. Table I presents the nominal and actual compositions of the alloys studied, together with the swaging and rolling temperatures. In all cases, these temperatures were in the a-ß field and the microstructures consisted of an equiaxed a-ß mixture. Melting and Fabrication—Except for the commer-

Jan 1, 1960

By R. A. Burmeister, P. E. Greene

Two methods for the synthesis and growth of single crystals of B6 P are described: a solution-growth process employing nickel as the solvent, and a vapor-growth process employing BBr3 and pH3 as the reac-tants. Relevant portions of the Ni-B-P phase diagram have been examined and liquidus data are presented for an isobaric section at an equivalent P2 pressure of 3.8 Torr, and an isothertnal section at 1300°C. Solution-growth techniques are described and the purity and crystalline perfection of the resulting material is discussed. Epitaxial growth of BeP on &P substrates has been obtained using the vapor-phase system. Evidence is presented which supports the assignment of the stoichioknetry B6P to boron sub-plwsphide. THE B-P system differs from other III-V systems in that it contains two distinct compounds. The existence of the monophosphide (BP) has been known for some time,' whereas the subphosphide (B6P) was reported only recently.' Both of these compounds are large bandgap semiconductors (Eg = 2.0 ev for BP~ and 3.3 ev for B6P4), and are therefore of interest for optoelectronic applications. The crystal structure of B6P is quite different from those of most semiconductors, being derived from that of a-rhombohedral boron by the incorporation of the two phosphorus atoms in the intericosahedral sites of the a-boron unit cell?76 B6P also exhibits a number of unusual characteristics, including a high degree of chemical inertness, hardness, and high-temperature stability. No information concerning other physical properties is available in the literature. The present study is part of a broader investigation of the preparation and properties of B6P. This paper considers methods of growing single crystals of B6P of suitable size and quality for physical-property measurements. A detailed discussion of the electrical and optical properties of B6P will be given elsewhere.' GENERAL CONSIDERATIONS The method first used to synthesize B6P was the disproportionation of BP' according to the reaction The equilibrium P2 pressures corresponding to this reaction were also determined .'" It is therefore possible, in principle, to apply several of the reactions reported for the synthesis of BP to the synthesis of B6P merely by selecting lower phosphorus pressures or higher temperatures, in accordance with the equilibrium data. Other techniques for the direct synthesis of microcry stalline B8P have also been reported.1°

Jan 1, 1968

By E. S. Bumps, H. D. Kessler, M. Hansen

The titanium-rich end of the Ti-AI phase diagram has been determined to the compound TiAI3 (62.7 pct Al), thus joining the aluminum-rich portion previously investigated by others and completing the diagram. Micrographic analysis and X-ray diffraction were the chief methods used to determine the phase relationships. THE Ti-Al phase diagram has been investigated as part of a program on titanium phase diagrams for the Wright Air Development Center. Included in the available information concerning the phase relationships in titanium-rich Ti-A1 alloys is a brief statement by Brown' that: "aluminum raises the transformation temperature to 1000°C (183Z°F)." This observation is interesting in that it is the first example of a metallic alloying component raising the transformation temperature of titanium, and consequently widening the field of the a solid solution. Busch and Freyer' presented resistivity data which indicated the formation of titanium-rich solid solutions of 1 and 3 pct A1 alloys prepared by powder metallurgy methods. Duweza found that there is only one other intermediate phase other than the known compound TiA1, (62.7 pct Al). This phase, designated as y, is of variable composition; its crystal structure is of the AuCu type and is therefore based on the composition TiAl (36.02 pct Al). Earlier work on the constitution of the aluminum-rich alloys has been reviewed by Hansen, and need not be discussed here. The tetragonal crystal lattice of TiAl,, as found by Fink, Van Horn, and Budge," was confirmed by Brauer." Recently, Schubert7 has reported that TiA1, is homogeneous within a limited composition range; however, the solubility limits were not given. The Ti-A1 phase diagram as presented in. this paper was determined by micrographic analysis of alloys containing from 1 to 62 pct Al, annealed at and quenched from temperatures between 700" and 1400°C. The phases and phase ranges investigated extend to the compound TiA1, (62.7 pct Al) to join the aluminum-rich end of the system determined by other investigators, thus completing the diagram. Methods of Investigation Preparation of Alloys: Iodide titanium, 99.9+ pct pure, obtained from the New Jersey Zinc Co., and high-purity (99.99+ pct) aluminum sheet from the Aluminum Co. of America were used to make up alloy ingots weighing 10 to 20 g. Detailed descriptions of melting techniques have been presented previously for work on the Ti-Mo and Ti-Cb> nd Ti-Si" phase diagrams. Briefly, the melting practice consisted of arc melting an accurately weighed charge in a copper block crucible insert in a non-consumable tungsten electrode furnace, under helium at atmospheric pressure. All ingots were carefully weighed after melting to detect possible losses. Comparison of weight before and after melting showed no appreciable weight changes. Also, chemical analyses were in close agreement with nominal compositions, Table I. The diagram as presented is, therefore, based on nominal compositions. Alloys were prepared having the following nominal aluminum contents: 1 ... 36 (1 pct increments), 38, 40, 41, 42.5, 44, 45, 46, 47.5, 49 . . . 64 (1 pct increments), 67, 70, 80, and 90. Ingots with up to 14 pct A1 were cold-pressed various amounts in order to increase the rate of attaining equilibrium structures on heat treatment. The amount of cold deformation that could be applied decreased with increasing aluminum content, until alloys containing 12 pct A1 or more cracked after only a few percent deformation. Annealing Treatments: Samples annealed at temperatures of 700" to 1000°C were sealed in

Jan 1, 1953

By Joseph B. Story, John T. Clarke

A modification, of the Kelvin bridge using an inductor was used to measure the conductivities of molten sodium chloride, calcium chloride, and mixtures thereof. A capillary-type four-lead fused quartz dipping cell was constructed. The effect of a small amount of potassium chloride on the conductivity of the melt was determined. IN the electrowinning of sodium and chlorine from sodium chloride in Downs cells, calcium chloride is added to the sodium chloride in an approximately equimolar amount to permit cell operation at a lower temperature. This lower temperature improves current efficiency and ease of operation, but decreases voltage efficiency by decreasing the electrical conductivity of the melt. A knowledge of the electrical conductivity of the Downs cell melt is necessary to the understanding of Downs cell operation, for the IR voltage drop across the melt is responsible for a significant part of the electrical power consumed by the cell. The work of previous investigators on fused sodium chloride-calcium chloride mixtures was reviewed from the standpoint of consistency with the results of others on the conductivities of the pure constituents. The electrical conductivity of pure fused sodium chloride has been established with accuracy by Van Artsdalen and Yaffe,1 by Edwards, Taylor, Russell, and Maranville,2 and by Lee and Pearson.3 It has also been studied by a number of other investigators.4-13 The best values for calcium chloride are believed to be those of Lee and Pearson,3 since the sodium chloride and potassium chloride conductivity values given by them check the best literature values. A number of other investigators have also reported values for calcium chloride.'-"."' Electrical conductivity data for fused sodium chloride-calcium chloride mixtures have been reported by Sandonnini,12 Vereshchetina and Luz-hnaya,18 Ryschkewitsch,11 Barzakovskii,5 and Alaby-shev and Kulakovskaya.15 Sandonnini reports no data at temperatures lower than 850°C. The conductivity values reported by Vereshchetina and Luz-hnaya, by Ryschkewitsch, and by Barzakovskii for pure sodium chloride and for pure calcium chlor- ide vary somewhat from the literature values believed to be best and the sodium chloride-calcium mixture data of these authors and of Alabyshev and Kulakovskaya (who give no data for the pure compounds) show significant variations. In view of these facts, it seemed that an investigation of the electrical conductivities of fused sodium chloride-calcium mixtures would be worthwhile. Apparatus Bridge System—The bridge used,in this investigation is diagrammed in Fig. 1. In general, the elaborations of this bridge over the simple Wheatstone bridge were for the purposes of a) eliminating lead resistances or making them accurately measurable, and b) eliminating major capacitative and inductive effects or balancing them against each other. Lead resistances in the lower arms of the bridge were kept as low as possible by making the leads short and of low resistance wire. This could not be done in the cell arm of the bridge because of the remoteness of the cell from the other bridge components and because of the high-resistance nickel or chrome1 wires used in the cell. Since maximum sensitivity is attained when the resistances of the four arms of the bridge are equal, 50-O resistors were used in the lower arms of the bridge when fused salt conductivities were being measured, and 1000-O resistors were used when the cell was being calibrated with normal aqueous KCl solution. The cell resistance was of the order of 50 ohms with fused salts and of the order of 1000 ohms with normal aqueous KC1 solution. The resistors used were non-inductive and accurate to 50.05 pct (General Radio Co. Types 500-C and 500-H). The lead resistance between point A in the cell and point E at the measuring resistor was eliminated by using the kelvin bridge principle; that is, the voltape drop across the lead from point A to point E was divided between the cell arm of the bridge and the measuring arm of the bridge in proporation to the resistaxes in the lower arms of the bridge.

Jan 1, 1958

By H. C. Casey, M. B. Panish

The roles of the phase diagram and the diffusion and solubility analyses in the selection of sources for the diffusion of zinc into GaAs are discussed. Isothermal sections of- the phase diagram are described at 1000°, 775°, 744°, and 700°. Below 744° the three solid phases, Zn3As2, GaAs, and ZnAsz, may be in equilibrium. In the composition regions where the three solid phases are in equilibrium, the partial pressures of the components do not vary with composition and there is no liquid phase. A diffusion source composition within that region containing 5, 50, and 45 at. pct Ga, As, and Zn was selected to yield reproducible diffusion profiles without surface damage. The 5/50/45 ternary source Provides a significant improvement in the reproducibility and planarity of- the zinc diffusion as compared with other zinc diffusion sources that result from starting with elemental zinc, dilute solutions of zinc in gallium, or various combinations of zinc and arsenic. Several experimental diffision profiles for the 5/50/45 diffusion source have been determined. The profiles are very steep in the region of the junction and produce devices that exhibit step junction behavior. The junction depth varies as the square root of time. Diffusion at 700°C for 4 hr gives a 5-µ junction depth and a surface concentration of 2.4 x1020 cm-3. The surface concentration is enhanced by a factor of three and the junction depth decreased by a factor of ten as compared with diffusion with a starting source 01- elemental zinc. The differences in dijyusion behavior with these two sources are due primarily to the approximately 10' greater equilibrium As4 partial pressure for the 5/50/45 source. ThE most common technique for the preparation of GaAs p-n junctions for diverse applications ranging from switching diodes to injection lasers has been to diffuse zinc into the solid from the vapor phase. The zinc impurity has generally been provided by introducing into a diffusion ampoule elemental zinc, dilute solutions of zinc in gallium, or various combinations of zinc and arsenic. For the purpose of eliminating surface deterioration, zinc has been diffused into GaAs through SiO2 films1 and from zinc-doped SiO2 films.2 During a study of the injection and recombination mechanisms in GaAs junctions, we found that these diffusion techniques either resulted in nonreproducible diffusion profiles and nonplanar junction interfaces or were extremely inconvenient to use. An unpublished report by Allen and pearson3 emphasized that an understanding of diffusion requires relating the diffusion conditions and system compositions to the ternary phase diagram. Recent studies have made it possible to relate the effect of starting source composition on the GaAs sample surface and diffusion profile reproducibility and, in addition, to estimate the expected surface concentration and zinc diffusivity. These studies include the Ga-As-Zn phase diagram,415 the determination of the incorporation reaction for zinc as a substitutional impurity,6 and the analysis of the concentration dependence of the diffusion coefficient.' In this paper the role of the phase diagram in the selection of the starting diffusion source composition is illustrated, and an application of the diffusion and solubility analyses is used to demonstrate their utility in the estimation of surface concentration and diffusivity for various starting source compositions. Consideration of the isothermal sections of the ternary phase diagram shows that below about 744° C a composition region exists where the three solid phases Zn3As2, GaAs, and ZnAs2 are in equilibrium without a liquid phase. In this region the partial pressures of the components do not vary with composition, and thus the surface concentration and diffusivity depend only on temperature. A diffusion source composition within that region containing 5, 50, and 45 at. pct Ga, As, and Zn was selected. As will be described in detail, this diffusion source yields reproducible diffusion profiles without surface damage, planar junction interfaces, and steep profiles that result in devices with step junction behavior. Only closed diffusion systems are considered. Open or flowing vapor systems require the maintaining of constant vapor pressures in the flowing gas and represent control problems outside the scope of this discussion.

Jan 1, 1969

By J. S. Hegwer, P. M. Dunlap

An improved acid for the treatrrzent of sulfate-con-raining limestones and dolomites is described. The acid is designed to reduce he reprecipitation of dissolved calcium sulfate and the possibility of plugging permeable flow channels. In addition, this improved acid has a much lower reaction rate than that of regular acid; the advantages of a "retarded" acid are obtainable. Field testing of the acid has shown it suitable for use in sulfate-containing formations. Substantial improvements in productivity generally resulted. INTRODUCTION Acid treatments of limestones, dolomites and other formations bearing carbonate deposits are frequently unsuccessful when the calcareous formation contains sulfate, either as anhydrite (CaSO,) or gypsum (CaSO4. 2H2O). Preliminary dissolution in acid followed by redeposition of calcium sulfate appears to be a major factor contributing to poor well performance after acidizing. The precipitate is usually the gypsum form of calcium sulfate, but in higher temperature formations it may be anhydrite. The freshly precipitated crystals are nearly always very small and needle-like. They may occupy a gross volume many times that of the original anhydrite crystals and will obviously constitute an impediment to flow through newly enlarged flow channels. It is believed that the redeposition problem is most severe when anhydrite lines the fracture systems and large pores which supply the effective permeability of a formation. Microscopic inclusions of calcium sulfate also present large sulfate surface areas for dissolution in acid. In either case, great amounts of calcium sulfate may dissolve before the acid can be spent on formation carbonates. For regular spent acid (originally 15 per cent hydrochloric acid) the precipitate could be as much as 270 Ib gypsum/1000 gal acid. Two techniques have been applied by the industry for reducing sulfate plugging during acidizing. The method'.' commonly employed in the field is the attempted removal of a quantity of regular treating acid before it has reacted completely with the formation. This is practiced because the solubility of calcium sulfate is greater in a solution that is still acidic than in one which has been largely spent on the formation rock. The chance of precipitative plugging is therefore reduced if the withdrawal is successful. However, it is often impossible to get the acid out of the formation before precipitation occurs. A second possible method, which at first glance appears practical, involves addition to the acid of sequestering agents which form strong soluble complexes with calcium ions. These chemicals do increase the "solubility" of calcium sulfate in fresh acid, but to a lesser extent in spent acid. The sequestering agents have, therefore, proved unsatisfactory because the amount of sulfate eventually deposited from the spent acid may be greater than that from regular acid. Another logical approach to the problem of calcium sulfate reprecipitation is the prevention of the initial dissolution of calcium sulfate by the common ion effect. This may be accomplished by adding a soluble calcium salt to the fresh acid. The use of calcium salts in treating acids is not entirely new. An earlier suggested use of a soluble calcium salt in hydrochloric acid apparently failed to recognize the full extent to which the solubility of calcium sulfate could be suppressed. The present study extends this earlier work and adds certain improvements toward the development of a practical anti-anhydrite acid. LABORATORY DEVELOPMENT Calcium Sulfate Solubility Table 1 shows the results of a laboratory study performed to establish the effect of calcium chloride concentration on gypsum solubility. Because of the strong tendency of calcium sulfate to form supersaturated solutions, accurate solubilities are difficult to determine. These solubility data probably are reliable to within ± 15 per cent. The solubility of calcium sulfate in 15 weight per cent hydrochloric acid increases with increasing temperature. This trend is also followed in hydrochloric acid which cantains calcium chloride. This is contrary to the solubility behavior of calcium sulfate in water, wherein the solubility decreases with increasing temperature.

Very few of those occupied in pursuits other than mining have any conception of the extent of boring operations that have been carried out on the gold and coal fields of Victoria, or of the valuable and definite knowledge obtainable by such means. The subject comprises various branches, which it will be necessary to describe in detail. The three main divisions are The Administrative, which includes all financial work and general management. The Professional, dealing with topographical and geological work necessary before any scheme of boring can be laid out, the preparation of plans, the inspection of cores obtained from bore holes, the examination of diamonds, etc. The Mechanical Branch, dealing with the drilling machinery, setting of diamonds, maintenance of stores, etc. In 1877, the Goverpment of Victoria decided to assist in prospecting the mineral resources of the colony by the aid of diamond drill boring, and for that purpose, a vote of £5,000 was passed, with which were purchased three diamond dulls, an American type being adopted.

Jan 1, 1901

By M. J. Pool, with Appendix by Larry Kaufman, R. W. Krenzer

Thermodynmic properties of the Cu-Mn system have been deterrrzined in the temperature range 973" to 1273°K by measuring the vapor pressure of manganese in equilibrium with alloys of compositions varying from 0.13 to 0.91 rnole fraction manganese using the Knudsen effusion technique. Activities of manganese calculated from the measured vapor pressures show large positive deviations. Calculated heats and entropies of mixing are positive with a maximum occurring at approximately 0. 7 mole fraction manganese. ThE investigation of thermodynamic properties of binary systems involving transition metals is of considerable interest at the present time. The incomplete subvalency electron levels of transition metals lead to unusual behavior in some alloys, and considerable information can be obtained by determining the thermodynamic characteristics of these systems and relating the thermodynamic behavior to observed physical properties. The Cu-Mn system, shown in Fig. 1,' provides an example of an alloy system in which the determination of the equilibrium phase diagram and various physical properties has received considerable attention, but very little work has been done on measurement of the thermodynamic properties. Elemental copper and manganese have comparable electronegatives, atomic sizes, and cohesive energies, but differ in crystal structure. They form a continuous series of solid solutions only at high temperatures and the structure varies in a continuous manner from fcc at the copper-rich end to fct at the manganese-rich end.' The purpose of this investigation was to measure the vapor pressure of manganese over a series of Cu-Mn alloys and from these values determine the thermodynamic properties of the binary system. Vapor pressure measurements were made in the temperature range 973" to 1273"K, remaining within the solid-solution region for each alloy studied. EXPERIMENTAL PROCEDURE The relative thermodynamic properties of solid Cu-Mn alloys were determined from vapor pressure measurements by means of the Knudsen effusion tech- nique. Several discussions of the theory can be found in the literature. In the case of copper and manganese, it is assumed that manganese is the only component subliming, so the vapor pressure of manganese over the various alloys can be determined directly by measuring the weight loss of the effusion cell. This is a valid assumption since the vapor pressure of manganese is about four orders of magnitude higher than the vapor pressure of copper in the temperature region of interest. The vapor pressure of manganese over the alloys at any given temperature is then related to the weight loss of the effusion cell per unit area per unit time. An upper limit of 1.5 x 10"s has been measured for the ratio of polyatomic to monoatomic molecules for manganese vapor in equilibrium with solid manganese at 1180°K, so it was assumed that manganese vapor is monoatomic. The effusion cells, fabricated from high-purity alumina, are 26 mm high, 18 mm OD, and have a wall thickness of 1 mm. Three different sized holes of 2.03, 2.54, and 3.18 mm diam were drilled in the lids from the inside face to minimize chipping, and the lids were then slip-cast onto the cells to provide a gas-tight seal. Alumina was selected for this particular application both because of its resistance to thermal shock and reaction with manganese vapor. In the ideal case, the orifice of the effusion cell should have a knife edge so that effusion through the orifice

Jan 1, 1970

By E. C. W. Perryman

The wide grooves formed at the grain boundaries when high purity aluminum is attacked by hydrochloric acid or sodium hydroxide have been attributed by earlier workers to the high energy of the grain boundary material. The effect has been investigated for high-purity AI-Fe alloys with up to 0.055 pct Fe as a function of iron content and heat treatment. It is shown that the explanation given above is untenable, but that the results can be explained on the assumption that iron segregates to the grain boundary in solid solution. IN 1934, Rohrmann¹ showed that aluminum of 99.95 pct purity suffered intercrystalline corrosion when immersed in 10 to 20 pct hydrochloric acid, and that the susceptibility to intercrystalline corrosion depended upon the heat treatment given. The greatest susceptibility was found for specimens quenched from a high temperature (600°C) and the lowest susceptibility for specimens cooled slowly from that temperature. Lacombe and Yannaquis2 have shown that super-pure aluminum (99.9986 pct) annealed at 600°C suffers intercrystalline attack in 10 pct hydrochloric acid and that this attack is intensified by anodic dissolution in the same solution at a current density of 10 milliamperes per sq dm. No difference in extent of intercrystalline attack was found between the 99.993 and 99.986 pct Al, which led the authors to suggest that impurities played only a secondary role in the mechanism of intercrystalline corrosion. It was found, however, that the attack at the grain boundaries depended upon the relative orientation of the grains, large differences in orientation favoring rapid attack. Boundaries where the two neighboring grains were similarly orientated showed high resistance to attack as did boundaries between grains which were in twin relationship. These observations led Lacombe and Yannaquis to suggest that the intercrystalline attack was due to lattice discontinuities present at grain boundaries. Assuming that the grain boundary is a layer three to five atoms thick and has a crystal structure which is a compromise between the two neighboring grains it is clear that the discontinuities will increase with increasing difference in orientation between the neighboring grains and hence the increasing tendency to intercrystalline attack. Roald and Streicher³ investigated the effect of heat treatment of aluminum alloys ranging in purity from 99.2 to 99.998 pct on the corrosion resistance in 20 pct hydrochloric acid and 0.30N sodium hydroxide. They found that in hydrochloric acid the intercrystalline attack appeared to be determined by the type and quantity of impurities present and by the relative orientation of the grains. No difference in the susceptibility to intercrystalline attack was observed between specimens quenched and those furnace cooled, from 575°C. In 0.30N sodium hydroxide some materials exhibited intercrystalline attack, this taking the form of V-notches. Rohrmann¹ offered no explanation for the greater susceptibility to corrosion of material quenched from 600°C. It seems possible that this difference is connected in some way with a different distribution of impurity elements in the quenched and slowly cooled specimens. The fact that Roald and Streicher8 observed no difference between quenched and slowly cooled specimens may possibly be due to differences in either rate of cooling or silicon content or possibly both. Both these would be expected to have an effect on the distribution of impurity elements. Although the rate of cooling used by Rohrmann was slightly more rapid than that used by Roald and Streicher the position cannot be clarified because Rohrmann does not give the silicon content and Roald and Streicher give the silicon contents of only a few of their alloys. That Lacombe and Yannaquis2 found no difference in corrosion behavior attributable to impurities between the two materials they used may be because both were of high purity compared with the aluminum used by Rohrmann.¹ Although they found no difference in the corrosion behavior of their two materials it is possible that the results obtained by Lacombe and Yannaquis may, nevertheless, have been influenced by impurity distribution, since, on the transition lattice theory of grain boundary structure, it would be expected that sparingly soluble impurities would tend to segregate to boundaries where the orientation difference is such that there is a greater density of atomic sites of suitable size to contain them. It was considered worth while, therefore, to examine the corrosion properties of a series of materials of differing impurity content with the objects of confirming the experimental observations made

Jan 1, 1954

By K. C. Strebig, C. W. Schultz, A. A. Selim

The effect of some organic additives in diamond drilling of quartzite was investigated in the laboratory. The drill was designed to measure the rate of penetration, the thrust, and the torque and to record each as a function of the distance drilled. A statistical plan was followed throughout the investigation and an equation representing the bit performance was derived from the mathematical theory of reliability. The drilling torque was found to increase with the use of additives while the sliding coefficient of friction and the wear coefficient decreased. The energy per unit volume consumed was found to increase with the use of additives. A hypothesis explaining the effects achieved with the additives is given. INTRODUCTION For some time researchers have attempted to increase drilling efficiency by adding certain agents to the flushing medium. Much of this interest is the result of the observations of Rehbinder, Shreiner and Zhigach1 They postulated that "...in processes for the mechanical destruction of solids, a region of increased crack formation is created in the deformed layers adjoining that surface of destruction, forming the predestmction zone. The surrounding medium (for example, a liquid) which wets a given solid will penetrate the embryo microcracks of the predestruc-tion zone. Increasing the molecular affinity of this liquid for the surface of the solid considerably facilitates the deformation and destruction by softening the solid in the zone of increased crack formation. In this manner, the hardness or strength of the deformed body is decreased by the influence of the penetration of the liquid into the predestraction zone." This is known as the "Rehbinder effect". Rehbinder's work has prompted many investigators to examine the effect of additives on the mechanical destruction of rocks. Engelmann, Terichow and Selim reported that the maximum penetration of the rock by a diamond point in a solution environment was at the isoelectric point of the solution.* Robinson reported that his results did not appear to support the theory of Rehbinder.3 Joris and .McLaren suggested that additives with surface tension lower than water will be more efficient in cooling the diamonds.4 Their effectiveness in removing the fine cuttings from the face of the bit will also improve the efficiency of the system. They reported an improvement in impregnated bit life and penetration rates with the use of soluble oil additives. In contrast, Long and Agnew, drilling with surface set bits, reported that lubricating agents increase bit temperature and wear.5 A significant change was reported6 in the mechanical properties of rock with polar additives. It was concluded that this change in the mechanical properties of the rock in the presence of the additive is due to the rock hydrophilic properties. Ethylene glycol, glycerine and anionic detergent were selected for this investigation because their surface tension is lower than that of water. The surface tension of these additives for the concentrations studied was 42 to 75 percent of the surface tension of water. A low surface tension additive would wet the surface of the diamonds more easily and hence would be more effective in cooling the diamonds. Another characteristic of these low surface tension additives is their effectiveness in removing the cuttings and preventing the flocculation of the formed particles in the drilling process. This article summarizes the results of an investigation performed at the laboratories of USBM, Twin Cities Mining Research Center. The objective of the investigation was to study the over-all effects of some organic additives on the performance of diamond impregnated bits in atmospheric drilling conditions only and not in downhole pressured conditions.

Jan 1, 1970

By Matti J. Saarivirta

The relative machinabilities of the precipitation-hardenable Cu-0.9 pct Cr, Cu-0.25 pct Zr, and Cu-0.9 pct Cr-0.25 pct Zr alloys are improved from 18 to 80 pct by 0.75 to 1.25 pct Pb. The Lead also improves the tensile strength, hardness, ad resistance to softening of the Cu-Cr and Cu-Cr-Zr alloys. When the alloy containing 0.7 to 2.2 pct Cr, 0.10 to 0.25 pct Zr, 0.75 to 1.25 pct Pb, and balance copper is solution-annealed at 1000°C (1830°F) and then aged at 525°C (Y75°F), tensile strength of 65,000 psi, 16 pct elongation, 62Rb hardness, and 84 to 87pct IACS electrical conductivity are obtained. The copper base Cu-Cr, Cu-Zr, and Cu-Cr-Zr alloys have high electrical and thermal conductivities, high strength and resistance to softening at elevated temperatures, but their machinability is poor, i.e., close to that of the pure copper. In the manufacture of various components such as welding electrodes or electrical and thermal conductors it is ofter desirable that the alloy have good machinability for high production rates and long tool life. Thus, alloys that combine these properties may be used not only for existing applications, but for new ones where good machinability is a requirement. This investigation was undertaken to improve machinability without impairing other desirable characteristics of the Cu-Cr, Cu-Zr, and Cu-Cr-Zr alloys. These commercial alloys contain about 0.4 to 1.2 pct Cr, 0.10 to 0.25 pct Zr, and balance copper. Lead was selected as an element that should improve the machinability and possibly other characteristics of the alloy. WORK PROCEDURE This investigation began with a study of the effect of lead on the hardness, tensile strength, electrical conductivity, and machinability of the binary alloy containing 0.10 to 1.30 pct Cr and balance copper. This was followed by an investigation of the effect of lead on the Cu-0.1 to 0.4 pct Zr and Cu-Cr-Zr alloys. The alloys were made from initially oxygen-free copper and for comparison some castings were made from phosphorus-deoxidized Lake Copper. Commercially pure chromium, zirconium, and lead were used for alloying. In melting the chromium was added to molten copper at 1400°C (2550°F), the heat held for 15 min at temperature, and the temperature then lowered to 1350°C (2460°F) when the other elements were added. The alloys were held for 15 min at this temperature and cast into a cast-iron mold. One-kilogram, 3-in.-diam castings were made. An argon cover was maintained during melting and casting to prevent oxidation. The chemical compositions of the alloys are shown in Table I. The micro structure and properties of the alloys were studied in the cast and wrought conditions prior to and after various solution-annealing and heat-treating cycles. The relative machinability was determined as a function of the lead content and compared with the free-machining Cu-lpct Pb alloy. To determine the machinability, 13/16-in.-diam cast specimens were cut by a machine hack saw using a constant cutting speed of 50 fpm, a fixed feed force, and a new blade for each alloy specimen. Molybdenum highspeed steel saw blades, 0.032 in. thick with 14 teeth per in., were used in all tests. No cutting fluid was used. Five tests were made on each specimen and the average elapsed time per test was taken as a measure of the relative machinability for that alloy. The variation of cutting time for each alloy was less than 110 pct.

Jan 1, 1969