Search Documents

By Richard G. Burdick

This Bureau of Hines report describes an interface between a minicomputer and peripheral device, The logic used to develop the device is discussed briefly, after which the device is described in detail; complete construction and operational details are given. The report should aid both in duplicating this device and in designing similar devices for different uses.

Jan 1, 1975

By H. K. Lin

During slow-cooling crystallization of iron-making blast furnace slags, most rare-earth elements in the feed recrystallize as cerite-calcium while scandium and europium concentrate in a sheet-like "mineral". The mineralogy of this "mineral" is studied with one of the objectives being the extraction of the "mineral" from the slag for recovery of Sc and Eu. This "mineral" has been identified as one of the mica group minerals and can be named as rare-earth-bearing barium fluorophlogopite. The mineralogical characteristics of this "mineral" are investigated and discussed. This "mineral" can be effectively recovered from the slag by flotation with dodecylammonium acetate or a combination of dodecylammonium acetate and sodium oleate as a collector.

Jan 1, 1996

By E. E. Creitz

Application of the usual chemical methods to the determination of beryllium in the mineral-dressing products of a spodumene pegmatite was found to be unsatisfactory as to speed, accuracy, sensitivity, and range of analysis. A spectrographic method is described for the determination of beryllium. Samples are ground, mixed with borax, high-purity, flake graphite, and an internal standard; then they are fused, reground, pelletized, and excited with a high-voltage-spark discharge. Investigation of several spectrographic techniques to overcome matrix effects are described. The method developed gives results for beryllium in the concentration range from 0.002 to 5.0 percent; the average probable error of duplicate determinations was below 3.0 percent of the quantity present. INTRODUCTION The main source of beryllium in pegmatite is the mineral, beryl. Many of the conventional methods for the determination of beryllium in beryl are not suitable for control purposes because of lack of speed and accuracy, especially in the range below a few tenths percent. Beryl resists the usual chemical attack and can be lost in a hurried chemical analysis.

Jan 1, 1958

By Leming Ou, Hongqiang Li, Li Zeng, Qiming Feng, Yiping Lu, Guofan Zhang

"The entrainment of sericite, especially in the presence of hydrophobic microcrystalline graphite, leads to the poor flotation selectivity of microcrystalline graphite ore. In this paper, it was attempted to reduce entrainment of sericite, selective flocculation of microcrystalline graphite using polyethylene oxide (PEO) was studied. For the sake of flocculate microcrystalline graphiteselectively, flocculation tests of microcrystalline graphite and sericite single mineral were conducted.To investigate the effect of selectiveflocculation of graphite on entrainment of sericite in microcrystalline graphite flotation, batch flotation tests of graphite single mineral and artificial mixtures were conducted; theflocculationselectivity of PEO of different molecular weight (M.W.) was alsocompared inartificial mixture flotation. Inthe end, the structure of flocs in different particle size was studied by sieve analysis and microscopic observation. The resultsindicated that PEO of molecular weightone million andtwo million could selectivelyflocculate the microcrystalline graphite and reduce the entrainment of sericite at a lower dosage; further increasingof the dosage of PEO(M.W. ?two million) led to hetero-flocculation between graphite and sericiteandmadethe ash content of concentrate increase again."

Jan 1, 2014

By T. Shumka, M. J. Druckenmiller

"INTRODUCTION As we push further into the 21st century and closer to a more efficient mine, safety and operational enhancements are the two major keys towards attaining success. The Crusher Vision Automation System (CVAS) is a technological advance that will allow an operator to achieve higher safety and higher operational goals in the same piece of equipment. The CVAS is a patent pending system and method for measuring and maintaining the closed side setting (CSS) on gyratory crushers. In the same equipment and technology package, the CVAS will also allow safer placement of main shaft pieces for maintenance and replacement. This technology yields multiple uses and allows a site to significantly enhance safety and operational efficiencies. This measurement technique is used to provide more accurate data and faster data collection times than current techniques used today. It will give crusher operators accurate and reliable measurement for the CSS in a live, operating environment. Measurement data can be collected in five minutes allowing for fast adjustment of the mantle position and subsequent enhancement and streamlining of a crusher and downstream flowsheet. The advantage of this system is that it is permanently mounted at the crusher location, where the operator can turn the system on and off as many times as they like throughout the day with a goal of maintaining a constant CSS gap based on production and maintenance criteria to help streamline operations and enhance safety efficiencies.Regarding its other main functional area, mainshaft maintenance, it allows this work to be performed remotely while keeping personnel safer and out of harm’s way. SAFETY ENHANCEMENT The safety factor enhancement with this system is extreme. It does not require the use of overhead cranes, cleaning out the crusher, lowering people into the crusher or having the operator lower paint cans or lead balls into the crusher pocket while the crusher is in operation for measuring the setting. In order to perform the CSS measurements, the operator only needs to operate the laser through manipulation of a joystick while watching the video feed. Danger of a person falling into the crusher while trying to take measures is eliminated, as are the effects of handling lead balls and tracer dyes."

Jan 1, 2015

By Jason Rock, Rob Thompson, Lee Julian

This paper presents an innovative shift in inhibited bulk products with specific reference to their manufacture and application.

Feb 1, 2020

By Gloria Contreras

The study aims to optimize the density of holes per tunnel section. The energy distribution, the one with the highest density, is used in the center of the diagram and is distributed homogeneously towards the contours with the lowest energies up to the contours to produce a perimeter control.

Feb 1, 2020

By M. Ge

Signal processing is a major challenge for In-Seam Seismic (ISS) technique. Fourier Transform is an important tool for signal processing such as frequency analysis. However, for ISS signal, localized information, especially time-frequency localization is even more important. Wavelet Transform (WT) provides another approach to study the signal as a function of frequency and time. The objective of this paper is to demonstrate the application and advantages of WT to seismic signal analysis. Both transmission and reflection signals from coal mine void detection experiments are analyzed. The results illustrate that WT appears to be a powerful and convenient method for the in-seam seismic signal processing.

Jan 1, 2007

By A Querzoli, B Williams

In late 2014 the Flinders Power Management Team was executing business improvement plans to ensure continued electricity generation until 2028 and beyond. Six months later, in June 2015, the Board announced the closure of the Flinders Power South Australian business, including the Leigh Creek Coal Mine, the Northern and Playford Power Stations located at Port Augusta and the 250km railway line. The announcement was preceded by a brief period of internal planning. A date was soon set for ceasing coal mining operations, being November 2015. The mine is unique in many ways. Located approximately 550km north of Adelaide the site has over 100 years of history and was formerly operated by the South Australian Government. Privatisation in 2000 saw the mine continue operation under Perpetual Leases from the South Australian Government. The leases included exemptions from multiple sections of the Mining Act 1971, obliging primary regulation under the Mines and Works Inspection Act 1920. The coal, being a low rank sub-bituminous brown coal, is prone to self-heating and spontaneous combustion. The mine and company town Leigh Creek were the economic and cultural heartbeat of the community. Facilities at the mine were shared by the community and vice versa. While many mines across Australia and the world enter periods of care and maintenance, few have been actively closed to the point of relinquishment (Bennett and Lacy, 2016). A swift decision to close, followed by a short mining operations shutdown period, presented significant technical and regulatory challenges for both the mine operator and for Regulators. The subsequent joint risk mapping process employed by Flinders Power and South Australian Mining Regulators was a unique real-world example of collaborative mine closure planning and execution. Lessons learnt are valuable for all mines, production facilities and for Regulators, even for those who may wrongly assume that closure is many years away. CITATION:Williams, B and Querzoli, A, 2018. Risk management for minesite closure planning and execution – start now! Lessons from the closure of the Leigh Creek Coalfield, South Australia, in Proceedings Life-of-Mine 2018, pp 68–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By J. C. Gibson, C. H. Stockwell

"The San Antonio gold mine is at Bissett, Manitoba, on the north shore of Rice lake, 100 miles northeast of Winnipeg. Gold was discovered on the property in 1911, but intensive exploration was not undertaken until 1926. Milling commenced on May 1st, 1932. Total amount of ore milled from that time until the end of 1946 was 1,766,670 tons, having a value of $18,378,317.GENERAL GEOLOGYThe rocks in the vicinity of the mine are Precambrian and include three groups, namely, the Rice Lake series of volcanic and sedimentary rocks, basic and acidic intrusions, and a younger formation of sediments known as the San Antonio formation (Fig. 1). The lower part of the Rice Lake series, consisting of flows of rhyolite, trachyte, and andesite with interstratified beds of agglomerate, occupies an area extending southward from Rice lake. The lake itself and the country to both east and west of its northern end is underlain by the next succeeding beds of the series, which are chiefly tuffs, arkose, and conglomerate, but include a thin band of basalt. Northward from the lake, these are succeeded by the upper beds of the series, first a thin band of basalt and, overlying this, porphyritic andesite flows interlayered with beds of volcanic breccia or agglomerate.The Rice Lake series has been invaded on the east side of the lake by a body of basic rock ranging in composition from gabbro to diorite and quartz diorite, now much altered. This is cut by younger sills and dykes of basic rock, probably diabase, the original texture of which is largely destroyed by alteration. Numerous dykes of feldspar porphyry, quartzfeldspar porphyry, and a few of a rhyolite-like rock, occur south of the lake, but are uncommon to the north. They cut the diabase and older rocks.Extending westward from Rice lake and lying with marked angular unconformity against all of these rocks is the San Antonio formation, consisting of cross-bedded, arkosic quartzite."

Jan 1, 1954

By Xia Hong-ying, Peng Jin-hui, Zheng Zhao-qiang, Zhang Li-bo

"Preparation of activated carbon from the walnut shell by microwave assisted steam activation was studied. Influences of the three parameters, activation temperature, activation duration and steam flow rate on the adsorption capacity and yield of walnut shell activated carbon(WSAC) were investigated,optimization process was obtained by the Response Surface Methodology (RSM). The optimum preparation conditions were as follows: activation temperature of 980°C, activation duration of 41 min and steam flow rate of 1.66 ml/min. The optimum conditions resulted in an activation carbon with an iodine number of 1025 mg/g and a yield of 52.17%, while the BET surface area, total pore volume and average pore diameter of WSAC were 1328m2/g, 0.72ml/g and 2.2nm respectively. The study supported the potentiality of comprehensive utilization ofWalnut shell and the benefits of the microwave heating.IntroductionActivated carbons are one of the most important adsorbent materials in modern society because of its abundantly developed pore structure, strong adsorption ability, high surface area and thermo stability. They have extensive application in many industries fields which include gas purification [1], catalyst supports [2] and other pollutants [3]. However, in recent years, the industrial production of activated carbon is facing the problem of raw material scarcity and high cost, which limit to be widely used. Therefore, the selection of an appropriate precursor plays an important role and it has become hot sport to seek cheap raw material to lower preparation cost. As a kind of reproducible resource, the waste from agriculture and forestry is a high-grade raw material for preparing activated carbon due to is high carbon content, such as palm shell [4], rice hull [5], and coconut shell [6]. At present Walnut shell is widely accepted to be a renewable source of biomass. According to statistics, there is more than 1000,000 tonnes of walnut shells are produced in China annually [7]. As a good precursor for activated carbon production, Walnut shell is a major agricultural waste, to make better use of the cheap and abundant agricultural waste, it is proposed for activated carbon production."

Jan 1, 2014

By Karl C. Dean

To assist in the reduction of environmental degradation resulting from milling operations, the Bureau of Mines has developed, and successfully demonstrated, chemical, vegetative, and combined chemical-vegetative procedures for stabilizing milling wastes under varying environmental conditions. Costs of achieving reclamation using these stabilization procedures are compared with those of other physical and vegetative approaches. The Bureau's chemical-vegetative procedure for establishing vegetation directly on fine-sized wastes compares favorably with other stabilization processes that have been used.

Jan 1, 1972

By M. E. Kundick, W. E. Dieter, L. Cohen

The major details of design and maintenance of a seamless stainless steel fume hood system , developed by the Bureau of Mines , are described and illustrated . Operating and housekeeping routines are outlined .

Jan 1, 1964

By W. J. Miles

Oil based drilling fluids utilize a number of industrial mineral products to accomplish oil and gas drilling in several environments where water based drilling fluids are less effective or inappropriate. These industrial minerals include: organically modified bentonite, organically modified lignite, barite, hematite, mica, calcium chloride and other salts. A variety of organic products are also utilized in oil based drilling fluid formulations. Oil based drilling fluids are preferred in several drilling situations because: they can be used to drill through water sensitive formations; they produce holes that are very close to the drill bit gauge; they exhibit high temperature stability; they are more environmentally acceptable; they minimize producing formation damage; they provide faster drilling rates when used with new polycrystalline diamond drill bits; they minimize pipe sticking and lost rig time.

Jan 1, 1986

By K. R. Nichol

The author points out that corrosion works 24 hours a day, every day. It is an economic reality that the cost of corrosion is inevitable and that its cost should be incurred in the least expensive way. An economic evaluation technique to properly assess its relative impact is the Discounted Cash Flow Method. Various remedial and corrosion control measures are available and these, when coupled with a planned corrosion control program, help reduce the cost of corrosion.

Jan 1, 1973

By William J. Douglas

Critical path modeling (CPM) has been used widely as a tool to manage large-scale projects having many activities which are conducted in series or parallel. The construction industry is a regular user of critical path modeling as a planning tool. In this context, the method is used to provide an orderly schedule for all activities to forecast delays, slippages, and problem areas and to identify critical activities where resources should be directed. It also identifies others which have slack time, and provides information on the degrees of freedom and flexibility available in completing the project. The purpose of applying critical path modeling to an underground mining system is not primarily for scheduling, but as an analysis tool. In observing underground mining systems, it Is clear that repeated sequences of activities must take place for mining to proceed efficiently. Some of these activities must be sequential, while others be carried out in parallel. The fundamental difference between critical path modeling applied to mining versus a large-scale construction project are: (1) The activities in a mining system are cyclic in nature. (2) The location of the activity varies, and the entire process is not thought of as co-located, as is the case in a construction project. Another important aspect of the network development for mining systems is the degree of detail that is desired. One can be concerned with very macroscopic networks which represent, for example, an entire mine life cycle. Networks representing this problem would be more closely analogous to those of a large construction project. On the other hand, one might be interested in evaluating alternative ways of developing a property or of mining in a given section. More detailed networks representing the section activities are necessary to evaluate system parameters and their impact on long-term production.

Jan 1, 1978

By Milton Manrique, Edgar E. Vidal, Patrick R. Taylor

"Ultrafine zirconium carbide powder has been synthesized using zircon concentrate and methane in a thermal plasma reactor. The effect of several experimental variables, such as power used and zircon particle size, on the conversion has been studied. A thermodynamic analysis of the possible reactions and stable compounds was performed. A mathematical model that describes the in-flight decomposition of zircon particles was developed based on a description of the temperature and velocity profiles calculated in the reactor. It was shown that the formation of zirconium carbide from zircon and methane is thermodynamically possible. Complete 'vaporization of zircon in the reactor is predicted when the particle size is below 45flm and the effective power entering the reactor is 15 kW. The powders were collected and characterized by XRD, SEM, TEM and chemical analysis using ICP. Results of the product analysis indicated the presence of zirconium carbide, zirconium oxide, silicon carbide and silicon oxide.IntroductionIn recent years there has been an increased interest in the production of nanometric sized powders of ceramic materials for use in advanced materials applications. One possible method to produce these powders is with a thermal plasma reactor, which offers high temperatures and fast quenching rates. This technology has been called - Thermal Plasma Synthesis - [1].Zirconium Carbide (ZrCx) has typical properties of transition metal carbides: elevated hardness - between alumina and diamond - a high melting temperature of 3420°C and high chemical stability at room temperature [2]. ZrCx has a Bl crystal structure with deficiencies in the number of carbon atoms in the cell with x between 0.6 and 1 [3]. Different methods have been used to produce ZrC, one method is by direct reaction of zirconium hydride or halide with carbon. Other methods used are direct reduction and carburization of zirconium oxide (Zr02) and reaction of metallic zirconium with a caburizing gas such as acetylene [3]. Recently small films of ZrC have been obtained using a sputtering device [4,5]. ZrC has been used in nuclear plants as a low neutron absorbing and high mechanical resistant refractory material and also as a constituent in cathodes made of UC-ZrC [6]. It is also used in the form of tubes, boats and crucibles to handle molten metals and as part of electronic devices used for thermoionic transducers. Recently ZrC has been used along with zirconium diboride (ZrB2) to produce composite materials [7,8]."

Jan 1, 1996

By S. M. Khandrika

Most of the coal presently used by the utility industry is cleaned at preparation plants employing wet processes. While water is the mainstay of coal washing, it is one of the least desirable components in the final product causing a reduction of the heating value as well as handling difficulties. Currently available dewatering techniques are inefficient for dewatering very fine coal (minus 325 mesh). The US coal industry has expressed serious concern about utilizing advanced cleaning processes such as column flotation because an efficient and economical dewatering process is not available.

Jan 1, 1992

By José Antonio, Silva Souza, Luis Alves Venancio, Emanuel Negrão Macedo, Antonio Ernandes M. Paiva

"The production of alumina from bauxite using the Bayer process generate 1.25 ton of the residue known by red mud and 460 kg of CO2 per ton of alumina.The direct use of exhaust gases from the alumina refineries to react and neutralize the bauxite residue may allow a double gain: open a wide range of new applications for bauxite residue reducing the reactivity of red mud and sequester approximately 15% or 67 kg of CO2 per ton of alumina.This paper shows the reaction of a suspension of bauxite residue-water with a simulation of the calcinator exhaust gases of the refinery. The influence of the temperature and the ratio water red mud is also analyzed.2 IntroductionThe production of millions of tons per year of alumina around the world generates around 1.25 tones of the residue known as red mud and 0.4 ton of CO2 per ton of alumina . The vast majority of the red mud is stored in large sealed lakes. Due to the high reactivity is considered dangerous and currently there is no operating process capable of reuse all the material at any refinery. These lakes after filled of solid material eventually have the surface revegetated. Otherwise will need monitoring for decades and remain as an environmental passive. The search of a industrial process that combine the reduction of the CO2 emission and the reduction the pH of the red mud opening the possibility of use in large scale in a economically viable way is the main objective of this work.The use of the exhaust gases of the refineries to neutralize the bauxite residue may allow a double gain: Open a large array of new applications for the residue with the reduction of its reactivity and sequester million of tones of CO2 plus other gases like SO2 [7] and NOx.This project main objective is to study the reaction of the CO2 with the Bayer process residue in order to obtain the basic parameters to design an equipment capable of process this reaction on a pilot scale. With this objective compositions of red mud on spray were processed with flow of gas containing CO2 at different temperatures and with concentration similar to the exhaust gases of the calcination process of the refineries. With the results, basic concepts of a pilot scale equipment were evaluated.A revision of the work already done on this type of residue were done [3, 9, 10]. Alternatives and potential barriers on chemistry and environmental fields were discussed. With the objective of industrial application the potential use of these materials were evaluated through the pH control, mass balance and x-ray diffraction."

Jan 1, 2010

Two concentrates from Palabora, in South Africa, containing 0.056-0.068% undesirable Cu and 0.8 or 2.2% Ti, were chlorinated with air:chlorine ratios of 10:1, 15:1 and 20:1 at temperatures between 1 200 and 1 329 K. The resulting volatile chlorides were condensed and the solutions analysed for Cu, Fe and Ti. Recovery of Cu was less than 25% at low temperatures and short reaction times, but at 1 258 K almost all Cu was removed from the magnetite at all ratios of chlorine to air. At higher temperatures, the increased carrying over of iron as FeCl3 could be minimised by decreasing the partial pressure of chlorine. No titanium was detected in the volatile products and the percentage of Cu recovered was independent of Ti concentration in the concentrates, though as a function of Cl2 vol%, more Cu was recovered at 1 200 K from the low-Ti than from the high-Ti concentrate. In a fluidised-bed reactor, Cu recovery was 58-90% and iron carry-over less than 10 ppm

Jun 21, 1905