Search Documents

By Richard L. Gordon

THE PROBLEMS AND POSSIBLE SOLUTIONS Toward the end of the 19th century, American industry began a drastic reorganization. The many, small, often-regional firms were supplanted by large national corporations-often produced by mergers among the existing firms. Giant companies appeared throughout American industry and many of them were engaged in the mineral industries.a The largest combines, by far, to emerge during the period were United States Steel and Standard Oil. Long before the restructuring had run its course, widespread concern arose over the process of concentration. Efforts were made to control, if not stop, the transformation. The concern produced the Sherman Antitrust Act of 1890 and the first of many federal regulatory agencies-the Interstate Commerce Commission (see Refs. 24, 31, 42). The basic objectives of these policies remain unclear to this day. The crucial issue is whether the goal is primarily to insure development of a more competitive economy or to preserve a social structure leaving more scope for small businesses. Complications arise from difficulties in agreeing upon the meaning of these terms. Studies of the early years of the antitrust movement suggest that it involved no particular concern over the mineral industries. Objections were directed at big companies in general. To be sure, the conservation movement arose in roughly the same period and did stress the evils of monopoly control of minerals. However, direct, continuing influence of conservation policy on antitrust is not apparent. Many of the most important antitrust cases, nevertheless, involved minerals. This, of course, may be sheer coincidence; the choice of cases has never followed any obvious pattern. Certainly, no simple hypothesis can explain the interest consistently. Once it may have been true that mineral industries were more likely than other sectors to be dominated by a few large companies. Yet, often sharp reversals of such tendencies -e.g., in oil and aluminum-have not removed antitrust interest. The importance of minerals to the economy cannot satisfactorily rationalize antitrust interest. The equally

Jan 1, 1976

By Nellie E. Guernsey, Louis J. Sousa, Alfred Weiss, Nickolas J. Themelis

Over the past decade, numerous factors have led US copper firms to face increasingly severe competition from low cost foreign producers. As a result, greater attention is being devoted to developing and implementing new technology that can reduce costs and maintain the competitive position of domestic firms while simultaneously meeting environmental requirements. To obtain a better understanding of the likelihood of the development, adoption, and use of innovative copper technologies in the future, the Bureau of Mines contracted with Mineral Systems Inc. of Stamford, CT, to undertake a systematic survey of technological experts in industry, government, and the academic community. According to the survey, major developments in exploration over the next 25 years are likely to be in technologies that facilitate analysis and interpretation of deposit data rather than those that enable the collection of additional data. Most new copper mining and beneficiation technologies are likely to represent evolutionary extensions of existing systems with a notable increase expected in the application of information systems technologies and computer control methods. A possible movement towards increased usage of continuous mining systems in copper was also noted. Experts indicated that several copper smelters are under consideration for extensive renovation and, as a result, flash smelting technology is expected to become much more widely used in the US. A gradual movement toward continuous smelting methods was also forecast. In copper refining, the major technological change expected is the gradual automation of various refinery operations. Finally, though increased usage is expected, in situ solution mining and hydrometallurgical processing of sulfide ores are not expected to become widespread over the forecast time horizon. This first article in a two-part series describes the survey method chosen and the technological innovations selected for eval¬uation. Also discussed are the assessment panels, background scenarios, critical events, and diffusion forecasts. Next month, part two will address technology forecasts resulting from the study. Featured are discussions on future copper exploration, mining, beneficiation, smelting, refining, and recycling. A cost/benefit analysis will also be included. Methodology Selection of Assessment Method To develop a consensus forecast of technological change in the copper industry, a technique for systematically polling subjective opinions of experts was required. After conducting a literature survey and some preliminary testing, the direct probability assessment method was selected. With this assessment method experts are asked to express in quantitative terms their judgment of the probability that a specified event will occur, usually over a series of time frames. The method was chosen because the experts were observed to be more comfortable with this approach during the testing period, and the results of this process effectively satisfied the assessment objective. The experts generally could provide more precise estimates of the timing of future events using this technique because it was the least cumbersome of the assessment methods tested. Identification, Selection, and Description of the Technologies The initial list (Table 1) of innovative copper technologies assessed in the study was developed from two principal sources: knowledge and expertise of the study team and a review of relevant technical literature. From this list of 47 potential technologies, 10 were selected for detailed assessment. Table 2 lists 35 technologies that were subsequently identified in the first series of assessments. Twelve technologies from this list were also selected for detailed evaluation in a second assessment round. Criteria used for the final selection of technologies for detailed assessment specified that: • The expected impact of each technology on copper supply (i.e.,

Jan 9, 1983

By Parke A. Dickey

Potential differences between strata of shale and sandstone have been recognized for about 15 years, and they form the basis of the electrical logging of oil wells. Hitherto these potentials have been ascribed solely to electro-¦ chemical reactions caused by the disturbing effects of the water in the drill hole through which they are generally measured. Observations by the author in wells empty of water and in a mine shaft suggest that potential differences between sandstones and shales are natural and specific properties of the rocks, although they are moditied in measurement by the disturbing effects of the water in the drill hole. The cause of these potentials probably is to be sought in the relative polar adsorptive capacities of quartz and clay particles. Introduction The existence of potential differences in the surface of the earth has been known for some time, and their measurement has facilitated the discovery of geological discontinuities such as ore bodies. The technique of measurement has been well established.1-3 In measurements in oil wells, it has been found that the potential of shales with respect to some arbitrary reference is very nearly constant in any one well, at least below the zone to which meteoric water has gained access. Sandstones and some other types of sedimentary rocks have a difference of potential with respect to shale that is negative arid may attain a value of 200 millivolts or more. The difference of potential, as usually measured commercially with water in the hole, is distributed over about one foot vertically at the top and bottom contacts of the sandstones. The sharpness of the curve at the formation contacts can be improved by using a short electrode that is close to the wall of the hole' These potentials generally have been ascribed to the disturbing effects of the water in the drill hole. Potentials have been found, however, in wells in which no water was present. In the course of experiments in electrical logging in pennsylvania, carried out by the pennsylvania Geological Survey, observations were made of several phenomena that hitherto have not been described, to the author's knowledge, ill the published literature. The potential differences across the contacts of sandstone and shale are called ill this paper "natural potentials," as distinguished from the potentials caused by electroendosmosis (electrofiltration) and concentration differences, which will be discussed subsequently. Potentials in Cored WeLl In the spring of 1942, the author measured the potentials in an exploratory well (Day 13, near Grand Valley, Pa.) which had been cored With diamond tools. The potentials were first measured with fresh water in the hole. * null balance potentiometer was used in this and all the other measurements described in this paper. One nonpolarizing porous pot electrode, containing copper sulphate solution and

Jan 1, 1946

By Parke A. Dickey

Potential differences between strata of shale and sandstone have been recognized for about 15 years, and they form the basis of the electrical logging of oil wells. Hitherto these potentials have been ascribed solely to electro-¦ chemical reactions caused by the disturbing effects of the water in the drill hole through which they are generally measured. Observations by the author in wells empty of water and in a mine shaft suggest that potential differences between sandstones and shales are natural and specific properties of the rocks, although they are moditied in measurement by the disturbing effects of the water in the drill hole. The cause of these potentials probably is to be sought in the relative polar adsorptive capacities of quartz and clay particles. Introduction The existence of potential differences in the surface of the earth has been known for some time, and their measurement has facilitated the discovery of geological discontinuities such as ore bodies. The technique of measurement has been well established.1-3 In measurements in oil wells, it has been found that the potential of shales with respect to some arbitrary reference is very nearly constant in any one well, at least below the zone to which meteoric water has gained access. Sandstones and some other types of sedimentary rocks have a difference of potential with respect to shale that is negative arid may attain a value of 200 millivolts or more. The difference of potential, as usually measured commercially with water in the hole, is distributed over about one foot vertically at the top and bottom contacts of the sandstones. The sharpness of the curve at the formation contacts can be improved by using a short electrode that is close to the wall of the hole' These potentials generally have been ascribed to the disturbing effects of the water in the drill hole. Potentials have been found, however, in wells in which no water was present. In the course of experiments in electrical logging in pennsylvania, carried out by the pennsylvania Geological Survey, observations were made of several phenomena that hitherto have not been described, to the author's knowledge, ill the published literature. The potential differences across the contacts of sandstone and shale are called ill this paper "natural potentials," as distinguished from the potentials caused by electroendosmosis (electrofiltration) and concentration differences, which will be discussed subsequently. Potentials in Cored WeLl In the spring of 1942, the author measured the potentials in an exploratory well (Day 13, near Grand Valley, Pa.) which had been cored With diamond tools. The potentials were first measured with fresh water in the hole. * null balance potentiometer was used in this and all the other measurements described in this paper. One nonpolarizing porous pot electrode, containing copper sulphate solution and

Jan 1, 1946

By A. W. Deurbrouck

The Bureau of Mines reviewed available data on the effect of crushing high-sulfur coals for the liberation of impurities in the light of increasingly stringent air pollution regulations. The survey, which provided information on Appalachian region coals only, indicated that such important coal-beds as the Upper and Lower Freeport and the Upper Kittanning show significant sulfur reductions when crushed to 14-mesh top size. For many other coalbeds amenability to sulfur liberation by crushing was indicated, although too few samples were available to draw firm conclusions,

Jan 1, 1966

By C. H. Riggs, Kenneth H. Johnston

The application of modern secondary-recovery methods has made possible the the extraction of more than 13 million barrels of crude petroleum from the eastern part of the Delaware-Childers field Nowata County, Okla., over and above the production that might have :been expected by continuing primary production methods, including the use of vacuum. Foremost among the secondary-recovery methods used in this foil was the repressuring of the Bartlesville sand with air and gas through injection wells spaced on sym-metrical patterns. Between 1925 and 1945, about 51 billion cubic feet of air and gas were injected into the producing formation, and the total recovery was increased from, 25 million to about 40 million barrels of oil. To produce as much as possible of the 28 million barrels of recoverable oil remaining in the sand will require the initiation of systematic water-flooding projects on many properties and the continuation of air and gas injection on others.

Dec 1, 1946

The issue of fine coal and tailings dewatering has become of increasing concern to many coal preparation operators, both in Australia and overseas due to a variety of factors. Increasing mechanisation and mining of thinner seams over the past decades has resulted in an increasing amount of fines generation while increasing international trade in coal and tighter environmental constraints on tailings disposal have resulted in the production of these same fines to be an increasing problem. However, technology to date has not always been able to supply a cost-effective solution to the handling of these fines in an efficient and environmentally benign manner. This paper will review the key issues associated with the dewatering of fine coal and tailings, will describe the major current practices and constraints, and finally will indicate alternative technologies that may have to be considered in the near future. For the purpose of this paper, "fine" coal is described as that material less than 0.5 mm in diameter (as this is the most common cutpoint between various plant circuits in Australian practice), although the technological constraints are very much dependent upon the fraction less than 45 micron. The amount of minus 0.5 mm material fed to plants varies, depending upon the type of coal and mining operation, but in Australia may range from less than ten per cent to greater than 30 per cent of the feed in higher rank coals.

Jan 1, 1991

By N. S. Stoloff, M. Gensamer

Pyramidal (1122) slip was observed in cadmium single crystals deformed in compression and bending at room temperature and —196°C. Crystals tested in tension twinned with no evidence of pyramidal slip. A critical resolved shear stress law for the propagation of twin nuclei appears probable. Twinning and low-stress kinking are believed to inhibit the appearance of pyramidal slip under ordinary experimental conditions. SEVERAL reports of nonbasal slip in cadmium have appeared in the literature recently, two of the reports having appeared after work on this project was in progress. Brown1 reported cross slip on electron micrographs, but did not identify the cross-slip plane. Wernick and Thomas2 observed nonbasal slip traces parallel to [1123] on a crystal bent with a pair of tweezers, but this too was an isolated observation, with no confirmation of the glide plane. The critical stress for pyramidal glide, and the temperature and strain rate dependence of glide on this system were not discussed. price3 has reported some observations of nonbasal slip in thin films of cadmium with the aid of transmission electron microscopy, but a full publication of these observations was not available at this writing. Pyramidal (1122) <1123> slip also has been observed on zinc single crystals4, 5 and (1122) <1010> slip on magnesium single crystals,6 all oriented with the basal plane nearly parallel to the specimen axis. Since the choice of slip system in the hexa- gonal metals is generally believed to depend on the axial ratio, with basal slip predominating for high-axial ratios, the occurrence of pyramidal slip in zinc and cadmium is unexpected. The objectives of the present investigation were to confirm the existence of nonbasal slip in cadmium, to identify the slip system, and to obtain an estimate of the critical resolved shear stress, assuming that the resolved shear stress law is applicable. EXPERIMENTAL PROCEDURE Two purities of cadmium, 99.95 pet and 99.99+ pet, were employed. As received bars were cold swaged to 3/16 in. rounds. Bicrystals and tricrystals were prepared by passing the polycrystalline rods through a gradient without seeds. It was desired to obtain a large yield of single crystals oriented xo* < 5 deg, in order to be able to suppress basal slip during deformation by keeping the resolved shear stress on the basal plane to a minimum. Cylindrical single crystals of cadmium were prepared by a seeding technique developed by Weiner,7 to obtain a predetermined orientation. The single-crystal rods were sectioned to specimen size by an acid-cutting technique originally developed for zinc crystals.&apos; An aqueous solution of nitric acid was the cutting agent. The acid was picked up by a plexiglass disc spinning at an optimum cutting speed through the acid, which was contained in a sump-like arrangement. The section to be cut, the acid bath, and the spinning disc were enclosed in a plexiglass case. The rod to be sectioned was coated with a thick layer of collodion. At the points at which sectioning was to be effected, the collodion was removed over a length of about 1/8 in. by dissolving it in acetone. To prepare a surface suitable for microscopic exam-

Jan 1, 1962

By George W. Maynard

In the course of an examination of some of the California hydraulic mines in November last, I visited the property of the Gold Run Ditch and Mining Company, near Dutch Flat, Placer County. This is one of the most important and extensively worked mines in the district. The gold occurs in the characteristic blue gravel, which averages 175 feet in thickness, the lower 40-60 feet being made rip of cement gravel, which resists the action of water, and can only he loosened by blasting. The specimen which I have the pleasure of laying before the members was presented to me by Mr. I. L. Gould, the intelligent superintendent of the mines, who informs me that he found it in the old river channel, about twelve feet above the bedrock. The flattened water-worn nugget of gold, about the size of a kidney-bean, is imbedded in blue cement gravel, around which quartz has crystallized. When found the projecting portion of the nugget was enveloped in quartz, the core of gravel and gold having only been discovered after breaking the lump of quartz. On the quartz there is a shell of cement. The specimen is a remarkable confirmation of the theory of the deposition of quartz from solution. DISCUSSION. Dr. T. STERRY HUNT, in commenting upon this occurrence, remarked that it is in accordance with what we already know of the recency of some of the quartz of this region, and cited the microscopic

Jan 1, 1880

By George W. Maynard

IN the course of an examination of some of the California hydraulie mines in November last, I visited the property of the Gold Run Ditch and Mining Company, near Dutch Flat, Placer County. This is one of the most important and extensively worked mines in the district. The gold occurs in the characteristic blue gravel, which averages 175 feet in thickness, the lower 40-60 feet being made tip of cement gravel, which resists the action of water, and can only be loosened by blasting. The specimen which I have the pleasure of laying before the members was presented to me by Mr. I. L. Gould, the intelligent superintendent of the mines, who informs me that he found it in the old river channel, about twelve feet above the bedrock. The flattened water-worn nugget of gold, about the size of a kidney-bean, is imbedded in blue cement gravel, around which quartz has crystallized. When found the projecting portion of the nugget was enveloped in quartz, the core of gravel and gold having only been discovered after breaking the lump of quartz. On the quartz there is a shell of cement. The specimen is a remarkable confirmation of the theory of the deposition of quartz from solution. DISCUSSION. DR. T. STERRY HUNT, in commenting upon this occurrence, remarked that it is in accordance with what we already know of the recency of some of the quartz of this region, and cited the microscopic

Jan 1, 1880

By William E. Ford, Edward Salisbury Dana

This section includes one distinct group, the Stibnite Group, to which orpiment is related; the other species included stand alone. Pyr., etc. - In the closed tube melts and gives a dark red liquid when hot and a red- dish yellow solid when cold; in the open tube (if heated ver slow? ) sulphurous fumes, and a white crystalline sublimate of arsenic trioxide. B.B. on ciarcoaTburm with a blue Hame, emitting arsenical and sulphurous odors. Soluble in caustic alkalies. Artif. - Realgar is frequently noted as a sublimation product from furnaces roasting ores of arsenic. Crystals are produced when arsenic sulphide is heated in a sealed tube with a solution of sodium bicarbonate. Obs. - Realgar occurs usually in veins associated with silver and lead ores. It has been found in volcanic regions as a sublimation~duct. It has also been noted as a deposit from hot spring waters. It is often rtasociate wlth orplment. It occurs at Felsi5bBnya, Kapnik and NagyAg, Hungary; Allchar, Macedonia. Binnental, Switzerland, in dolomite. In the United States, at Mercur, Utah; in the Norris Geyser Basin, Yellowstone Park, as a deposition from the hot waters. Found at the Monte Cristo millin district, Snohomish Co., Washington: the namerealga7 is from the Arabic, Rahj af gh&r,powder of the mine. Use. - Was used in fireworks to give a brilliant white light when mixed with saltpeter and ignited. The artificial material is now used for this purpose.

Jan 1, 1922

By H. C. Fiedler

The solubility of sulfur in Si-Fe was determined by the metallographic examination of heat-treated and quenched samples. In the absence of manganese, the solubility in 3.1 pct Si-Fe was found to be about 0.010 pct at 1000o C, 0.015 pct at 11000C, and 0.020 pct at 1150°C, which is substatntially less than hitherto reported. Increasing the silicon content was found to decrease the solubility of sulfur, which is consistent with the increase in the activity coefficient of sulfur with increasing silicon content that has been reported for Fe-Si alloys. Manganese additions were studied in alloys containing 3.1 pct Si and between 0.013 and 0.015 pct S. At low manganese levels the solubility product of manganese sulfide was found to be lower than previously reported. THE solubility of sulfur in pure polycrystalline iron has been reported by Rosenquist and Dunicz1 and by Turkdogan et al.2 Samples were equilibrated in atmospheres containing different ratios of H2S/H2. Both groups of investigators found a solubility limit in y iron of 0.013 pct at 1000oC and 0.031 pct at 1200°C. In addition, Rosenquist and Dunicz1 found a solubility limit in a iron of 0.020 pct at 900°C. Ainslie, Hoffman, and seybolt3 found significantly higher sulfur contents in polycrystalline iron samples than in single-crystal samples after heating at 890°C in a sealed tube containing a mixture of powdered iron and FeS made with s35. Whereas the single crystals contained 0.013 and 0.016 pct S (± 0.005 pct), the polycrystalline samples contained between 0.016 and 0.026 pct S. Autoradiographs suggested that the excess sulfur in the polycrystalline samples was due to the segregation of sulfur in solution at grain boundaries. Ainslie and seybolt4 have reported on the solubility of sulfur in 3 pct Si-Fe. Their samples were sealed in capsules containing hydrogen and sufficient sulfur as cobalt sulfide to saturate the sample. After heat treating, the sulfur-rich phase on the surface was removed by abrading, and the sulfur content of the sample was taken as the equilibrium value for that temperature. Before the equilibrating heat treatment, the samples were heated to 1300°C to coarsen the grains. The resulting grain size, which was about 3/18 in. in diam, was considered sufficiently large to preclude a sensible increase in sulfur solubility due to grain boundary segregation. They reported the solubility to be 0.029 pct at 900oC, 0.063 pct at 1000oC, 0.076 pct at 1100°C, 0.122 pct at 1200°C, and 0.098 pct at 1300°C.

Jan 1, 1968

By Robert U. King

The Climax Molybdenum Company&apos;s mine is situated on the Continental Divide at Fremont Pass in Lake County, Colorado. Elevations at the mine range from 11,000 it. to over 12,000 ft. The ore body is on the south flank of Bartlett Mountain, a prominent peak in the Ten Mile Range. A horizontal section of the mine, such as the Phillipson level (Fig. I), shows the outer ore zone as an annular ring varying in width from 300 to 800 ft., surrounding barren silicified rock. In vertical section the outer ore zone is dome shaped (Figs. 2 and 3), the apex of which is truncated at the surface by glaciation, exposing part of the ore body. The outer ore zone overlies the barren core and is itself overlain on the flanks of the dome with unmineralized rock. An ore zone of similar shape underlies the barren core of silicified rock, known as the Central Ore Zone (Figs. 2 and 3). Molybdenite is distributed uniformly through a zone of moderately silicified granite, schist and quartz monzonite (early) porphyry, around a highly silicified core. The molybdenite occurs in veinlets associated with fine granular quartz and pyrite, replacing altered and fractured granite, schist, and porphyry, and as coatings on numerous fractures cutting these rocks. Intense fracturing of all rocks is a characteristic feature of the Climax ore body. Most fractures are mineralized and no longer represent planes of weakness. Much fracturing is postmineral, however, and these fractures are generally filled with sericite or gouge, or remain as unmineralized joints separating otherwise massive rock into blocks of various size. Study and Mapping of Caving Characteristics Important differences in the behavior of caving of various blocks of ore at Climax have been recognized, involving arching of the rock over caved stopes, tendency of caved rocks to funnel, and size of caved rocks. Also, new problems have arisen associated with future mining on the Phillipson level, and may occur with proposed development of lower levels, such as excessive stress on mine pillars caused by large masses of overlying stable rock, and higher costs in maintenance of mine workings in soft, weak rock. To explain the differences and to provide solution for these problems, a study of geologic structure was undertaken early in 1944, to determine whether it would be possible to map cavability of rock from physical features exposed in mine workings and in diamond-drill cores. A comparison of known caved areas was made and rocks were classified structurally according to strength or degree of cavabil-ity. As nothing of this nature had been done before at Climax, the approach to the problem was rather indefinite. Several trials were made with negative results, but collectively indicated a suitable method. This was to examine all mine workings and diamond-drill cores, record-

Jan 1, 1946

By William P. Roe, James F. Ellis, W. P. Fishel

This paper reports the distribution of sulphur between iron and titanium in Fe-Ti-S alloys and in Fe-Ti-C-S alloys. The compound TiS was found, which exists as a separate phase at temperatures below 1200°C. Titanium in steels reacts with sulphur in preference to carbon. THE general relationship between sulphides and oxides suggests that titanium should form a sulphide having properties similar to those of titanium oxide. Specifically, titanium should form a sulphide having a high melting point, indicating a stable compound of low solubility in iron. In order for titanium to function as a desulphurizer or sulphur-fixing agent, it must form a stable sulphide. In order for titanium to be useful in steels as a sulphur-fixing agent, it must react with sulphur in preference to carbon; and to prevent red shortness, the sulphide formed must have solubility characteristics such that grain-boundary precipitation of a low melting phase be prevented. The terms desulphurizer and sulphur-fixing agent when used in this paper mean that titanium effectively ties up the sulphur as a stable sulphide of titanium and prevents the formation of FeS. The partition of sulphur between iron and titanium was studied first in a series of Fe-Ti-S alloys with carbon absent, and then in similar alloys with carbon present. It has been established1 a that titanium forms in Fe-Ti-S alloys a sulphide of undetermined composition which can be identified microscopically, and that the titanium-sulphur compound does not respond to sulphur printing. It has been suggested" that titanium acts as a sulphur-fixing agent, although little proof has been given. A report% f The Advisory Committee on Metals and Minerals summarizes the existing knowledge concerning substitutes for manganese in steels. Distribution of Sulphur Between lron and Titanium with Carbon Absent The alloys for this investigation were made by -melting Armco iron, metallic titanium, and iron sulphide in alundum crucibles in an induction furnace. The titanium was added after the other ingredients had melted. In these alloys it is recognized that some TiO, is present, since the melts were made in the air and since no other deoxidizing agent was used; therefore, some of the titanium was not available for union with sulphur. Thirteen ingots were made. Ingots 2 to 8 were cast in baked-sand molds; ingots 12 and 13 were cast in metal molds; and ingot 9 was allowed to cool in the crucible in which it was melted. All ingots were annealed at 900°C for 3 hr and were cooled slowly in the furnace. Subsequent information indicates that this anneal had no effect upon the titanium sulphide particle size, since the sulphide does not go into solution at this temperature. The ingots as-cast were approximately 8 in. long and % in. diam. The compositions of the eight ingots and the results of the partition of sulphur are recorded in Table I. Total titanium and total sulphur were determined by standard gravimetric methods. Sulphur, as iron sulphide, was determined by the evolution method. Boiling HC1 (1:4) liberates the sulphur from iron sulphide, but leaves the titanium sulphide practically undecomposed. A complete separation of titanium sulphide and iron sulphide cannot be made by digesting these compounds in dilute HC1 since titanium sulphide was found to dissolve slowly. The amount of titanium sulphide decomposed will depend upon the time in contact with the acid and upon the particle size of the sulphide. The point

Jan 1, 1952

By A. Vignes, J. P. Sabatier

A study of ternary diffusion at 1315°C in the Fe-Co-Ni system covering the entire ternary phase diagram has been carried out. Experimental values of the four interdiffusion coefficients DFeNico,DFeCoCo, DFeCoNi were computed at 33 points of the ternary diagram. The limiting values of these coefficients on the three sides of the ternary diizgram have also been determined. This set of data is presented as a contour map on the ternary isotherm for each of the four coefficients. Assuming that the Fe-Co-Ni system can be considered as ideal, the phenomenological coefficients Lk ij (with k = Fe) have been computed and the Onsager reciprocal relutions verified. It is shown that, in the Fe-Co-Ni system, the diffusion process can also be described by only two interdiffusion coefficients DFeFe and DCoNiFe, the second cross diffusion coefficient DCoFeNi being equal to zero and the second direct difusion coefficient being given by The values of the cross interdiffusion coefficients and of the Onsager coefficients are explained in terms of atomic mobilities of the three components with the help of a kinetic calculation due to Lane and Kirkaldy.8 It is shown that all the results are explained if the tracer difusion coefficients of the three components are such that DFe > DNi ~ DCo in complete agreement with experimental data on the three binary systems. DIFFUSION in a ternary alloy system is basically and significantly different from diffusion in binary alloys. In binary diffusion, there is just one independent composition variable and only one coefficient Dij is needed to describe the interdiffusion process. In ternary diffusion, we must allow for cross interaction between two independent species, and four interdiffusion coefficients are necessary to describe the transport process. Kirkaldy et al.1,2 have determined interdiffusion coefficients in the systems, Cu-Mn-A1 and Zn-Cu-Al. Guy and Leroy4 have reported intrinsic diffusion coefficients for the r phase at 1300°C of Co-Ni-Cr alloys as a function of composition using the analysis of Philibert and Guy.3 Interdiffusion coefficients were measured at three different compositions at 850°C in the single phase copper-rich corner of the Cu-Zn-Mn system by Dayananda and race.5 Zie-bold and Ogilvie6 have determined interdiffusion coefficients in the single-phase field of the Cu-Ag-Au system at 725°C. Preliminary results on diffusion at 1136°C in the system Fe-Co-Ni have been reported.7 In this study, data are reported on a more complete determination of interdiffusion coefficients in the Fe-Co-Ni system in the entire ternary at 1315°C. There is complete solid solubility with the fcc structures at 1315ºC, and this system can be considered as nearly ideal. This approximation allows the computation of the Onsager phenomenological coefficients. These values can then be used to test a kinetic calculation of the Onsager L coefficients in ternary substitutional solid solutions due to Lane and Kirkaldy.8

Jan 1, 1970

By Donald L. Katz

Charts for predicting the pressure to which natural gases may be expanded without hydrate formation have been prepared for gases of even gravity. Pressure-temperature curves for hydrate formation were established for gases having gravities from 0.6 to 1.0. These curves and the thermal behavior of the gases during free and adiabatic expansion were used to prepare the charts for estimating the permissible expansion of natural gases without hydrate formation. The problem was solved by L. F, Albright, W. T. Boyd, J. J. McKetta, G. Martin, P. Poettman. and A. P. Snyder.-, who are first-year graduate students in the department of Chemical and Metallurgical Engineering at the University of Michigan. This paper is essentially a summary of their results. Prediction of Conditions for Hydrate Formation in Natural Gases Each natural gas under a given pressure will form solid hydrates at a corresponding temperature provided sufficient water is present.1-5 The temperature of natural gases below about 5000 lb. per sq. in. decreases when the gases are expanded freely.6,7 This decrease in temperature may cause the expanding gas to enter the region of temperature and pressure at which hydrates will form&apos; The final pressure to which a natural gas may &apos;be expanded without hydrate formation depends upon the initial temperature and pressure and the gas composition. This paper presents charts that give the final pressures to which gases of gravity 0.6 to 1.0 at given initial temperatures and pressures may be expanded without formation of hydrate. Hydrate-forming Temperatures and Pressures as a Function OF Gas -Gravity Experimental data of pressure versus temperature at which solid hydrate will form, provided sufficient water is present, are available for a series of gases.2,3 A method of predicting the pressure-temperature curve for a given gas composition has been reported.&apos; The solution to this problem requires that these curves relating pressure to temperature be established for gases of given gravities.

Jan 1, 1945

By William R. Patterson

ACCORDING to the phase diagram for the Mn-Ni system,&apos; the high-temperature, fcc y-manganese solid solution is stabilized to below room temperature, in the range approximately 22 to 28 wt pct Ni. However, pearson2 cites evidence in the literature showing that for manganese contents greater than about 75 wt pct the quenched phase in Mn-Ni alloys is fct. This is in keeping with zener&apos;s3 suggestion that in manganese-rich alloys the fcc high-temperature phase undergoes a diffusionless or martensitic transformation to a fct structure upon quenching. Work by Basinski and christian4 on manganese-rich compositions in the similar alloy system Mn-Cu established that in alloys of greater than about 82 wt pct Mn the y-manganese phase underwent a fee fct martensitic transformation upon quenching to room temperature. Striking evidence for this martensitic transformation was the highly twinned or banded microstructure, an example of which is shown in Fig. 1. Similar microstructures have also been found in quenched Mn-Cr5 and Mn-Au6 alloys. In the present investigation, we attempted to obtain similar evidence of a fcc — fct martensitic transformation in manganese-rich Mn-Ni alloys. Manganese alloys in the range 10 to 30 wt pct Ni were prepared by arc-melting, under argon, at atmospheric pressure. The alloys all were 50 g in size, and negligible weight loss occurred during melting. The starting materials were electrolytic manganese and nickel, both of 99.9+ pct purity. The alloys were subsequently homogenized 48 hr at 1750°F, hot-rolled 50 pct at 1700°F, annealed 2 hr at 1700°F, and water-quenched to room temperature. All heat treatment was done in purified argon. Both X-ray and metallographic techniques were used to examine the structures of the quenched alloys. X-ray diffractometer studies were conducted on powder specimens obtained from filings rean-nealed 2 hr at 1700°F in argon and water-quenched. Identification of the intensity peaks from the diffractometer counter traces showed that below about 10 to 12 pct Ni the y phase decomposed partially upon quenching to give an a- + ?-manganese structure. In the range approximately 12 to 25 pct Ni, the structure was found to be fct ? manganese with a c/a ratio approaching 1.0 at 25 pct Ni. Beyond approximately 25 pct Ni, the structure remained fcc. These results, including lattice-parameter determinations, are given in Table I. Metallographic examination. was carried out on specimens polished and etched after quenching, and also on polished specimens reannealed and quenched. In the first case, the distinctive twinning or banding so prevalent in Mn-Cu alloys was sought, while in the second, the surface relief effect generally regarded as being truly characteristic of a martensitic transformation was sought. The microstructure of representative alloys in the range 12 to 25 pct Ni is shown in Fig. 2. The structure of the Mn-15 pct Ni

Jan 1, 1965

By C. G. Dunn

This note describes a method for revealing micro-structures in tantalum through an {hkl} effect which was found during a study involving amorphous and crystalline tantalum oxides. Three steps are involved. First, an amorphous film of Ta2O5 is formed anodically1 on the surfaces of the tantalum. The amount needed depents on the thickness of the substrate tantalum; 1600Å of oxide, however, is generally satisfactory in the 1/2 -mil (12 µ) to 3-mil thickness range. The film at this point is uniform in color. Second, the anodized specimen is heated to 800°C in. vacuo during a period of a few minutes and held at temperature for 5 min. During such a treatment some oxygen leaves the oxide through dissolution into the substrate tantalum (e.g., at 10-8 Torr oxide films thinner than about 800 completely disappear on 5-mil strip). Considerable crystallization of the amorphous oxide also occurs adjacent to the metal/oxide interface but not throughout the oxide thickness. The thickness of oxide needed as a residue is not too critical; values between 500 and 1000Å (optical estimate&apos;) may be most useful. (The presence of a residual oxide layer after the heat treatment usually is not apparent; in fact, in most instances the surfaces have a metallic appearance. This can be the case also for thicker residual films needed in the detection of a crystalline oxide phase by surface X-ray diffraction—e.g., if the initial oxide film is 3000Å thick, enough crystalline oxide is formed for X-ray detection.) The third step eliminates the metallic appearance at the surface and reveals (or produces) a varied colored film of tantalum oxide. Two methods can be used and both will be illustrated. If the specimen is dipped in 48 pct HF for a few seconds, the tantalum is found to be covered with a multicolored oxide. Moreover the colors correlate with the grain structure of the substrate tantalum through an orientation dependence of the type illustrated in Fig. 1, where results of an orientation analysis by the Laue X-ray method have been plotted. Other film conditions would have provided a different set of colors for the same orientations. Any such correlation, however, provides a basis for a qualitative assessment of the distribution of orientations in a large sample. The cold-rolled structure of tantalum foil produced by a recrystallization anneal and a cold-rolling reduction of 95 pct is not easily obtained by usual metal-lographic methods.&apos; The structure, however, is easily revealed by the present technique, Fig. 2. The alternative third step is to reanodize the specimen. The optical nature of the final anodic film depends on the presence of the crystalline oxide phase; color variations indicate optical thickness variations in the film. As the reanodization voltage is increased from zero, straw and light brown colors appear (as usual), followed now by variations in color from grain to grain depending on {hkl} orientation. Suitable end points, which are determined by voltage and time, are easily established. Fig. 3, for example, shows the grain structure developed in 5-mil tantalum strip during a 30-min re-crystallization and grap-growth anneal at 1800°C. An anodic film of 1600Å thickness was added prior to the special 800°C anneal. Reanodization was done at constant current density (near 0.2 ma per sq cm) in an aqueous solution of H3PO4 (0.01 pct) and was terminated after the initial brown colors were replaced by a deep blue at approximately 30 v. Although good grain contrast can be obtained with bright field illumination, even greater contrast for black and white micrographs may be obtained with polarized light, as in Fig. 3.

Jan 1, 1967

By K. H. Singh, J. N. Szuck, J. A. Riddell

"Hydraulic rock drilling equipment has been in use at Falconbridge over the past two years in both production and development situations. This paper deals with the experience gained in the application of hydraulic drilling in the company&apos;s mines and discusses the benefits and problems encountered during their use. The paper primarily focuses on technical, operating, maintenance and economic aspects of the machines, and does not attempt to compare the performances of different machines from the various manufacturers.IntroductionThe Sudbury Operations of Falconbridge Nickel Mines Limited are comprised of five operating mines and two mines under development. All the production comes from underground mines, mostly at depths below 1000 metres. The company, faced with increases in operating costs and difficult mining conditions, has continued to seek solutions with the help of new mining technology.The development of electric-hydraulic drilling machines in Europe had been pursued with great interest and, in 1979, a decision was made to test these machines to prove their technical and economic viability under operating conditions. Since then, a number of electric-hydraulic machines have been evaluated in different situations and currently nine hydraulic machines are being used in the company&apos;s various mines. These machines are comprised of two-boom drilling jumbos for development, one-boom machines for longhole drilling and a large-hole-diameter drilling rig for blasthole drilling. One hydraulic jumbo has also been used in a cut-and-fill stope."

Jan 1, 1982

By E. A. Gulbransen, W. S. Wysong, K. Andrew

INTRODUCTION THE reaction of carbon in solid solution in a metal with the surface oxide film on many metals may be inferred from thermodynamic calculations for high vacua and high temperature conditions. Holm1 has recently shown that oxide films may be removed from ferrous materials by heating in a vacuum at high temperatures and that carbon is the essential element in the reaction. Considerable work has been described in the literature on the decarburization reaction. Several general references may be noted.2,3,4 However, the nature of the mechanism involved in the decarburization is not well understood. Our interest in this reaction resulted from many attempts to degas and to reduce by pure and dry hydrogen the surface oxides 0n strips of various types of chrome-nickel alloys. Some of the early experiments on the behavior of 13 pct chrome-iron in vacua of the order of 5 X 106 mm and at a temperature of 600°C have been reported.5 These experiments showed a slow reaction with the residual oxygen or water vapor in the system and no reaction with hydrogen. This is in accord with thermodynamic data which would lead to the prediction that it is extremely difficult to maintain a hydrogen atmosphere at 600°C pure enough to reduce Cr203 formed on the surface. The crystal structure of the superficial oxide film formed on 13 pct chrome iron and Nichrome V has been investigated in the thin film range by Gulbransen, Phelps and Hickman,6 and shown to be Cr203. It was surprising to us to note that when a specimen of Nichrome V containing approximately 80 pct nickel and 20 pct chromium was heated to 850°C in a high vacuum, the specimen&apos; lost weight. The rate of weight loss was very temperature sensitive. A study of this reaction in vacua and in a hydrogen atmosphere is the subject of this communication. TYPE REACTIONS Let us consider the various reactions which may occur when a metal is heated in vacua, in a hydrogen atmosphere, or in an oxygen atmosphere. The number and kind of reactions will depend upon the chemical nature, of the metal, its alloying constituents and the location of the alloying constituents. The metals used in this study are chrome-nickel alloys of the heater type. They consist essentially of chromium, nickel and iron, small amounts of carbon, silicon and manganese and traces of zirconium, calcium, aluminum and magnesium. The trace elements are added to improve the lifetime and other characteristics of the alloy when used as a heater. Seven of the more important reactions with which we are going to be concerned here are as follows: [I. Metal • (gas) ;--* metal + gas - degassing of the metal 2. xM(s) + y ½ 02(g) tom- M.0„ (s) – oxidation]

Jan 1, 1948