Search Documents

By K. Huessener

INTRODUCTION THIS paper attempts a survey of the principles involved in the com¬bustion of blast-furnace gas in boilers and stoves. I do not expect to be able to give much information which is actually new, since the laws and methods of calculation pertaining to this problem are contained in a number of handbooks; but, so far as I am aware, they have nowhere been treated exclusively with reference to this one problem of gas economy. The road which I follow is less that of strictly scientific research than that of the practical engineer, faced by operation problems which require a. quick solution by easily accessible means without a prolonged search in scientific handbooks. For this purpose I give a number of tables and diagrams, as well as the results of many years' practical working experience as combustion engineer, which I trust will prove useful to my readers. HISTORICAL Considering the tremendous efforts made during the last 15 years to increase the efficiency of all kinds of power plants, it is highly surprising that until a comparatively very recent period, progress in the economical combustion of blast-furnace gas has been so slow. The explanation generally put forth, that fuel has been so cheap that it was hardly worth while to bother about this economy, will not hold good, for the greatest trouble was taken to improve the combustion of coal and to reduce the consumption of steam. The most plausible explanation appears to be the general impression, held as an accepted fact, that gas, especially hot, uncleaned, blast-furnace gas, was not a good boiler fuel. Many managers of high repute had tried unsuccessfully to improve the conditions of its use, and the dictum went forth that efficiencies of over 60 per cent., particularly with high loads, were impossible. This was the situation not only in the United States, with very cheap fuel, but also in Europe, where fuel prices are twice and three times as high.

Jan 2, 1916

By E. C. Carris

The loading of bituminous coal mechanically was recognized about the year 1900, but during the following 28 years less than 5 per cent of the bituminous production in the United States was loaded by mechanical means. During the past 16 years, however, the usage of some form of mechanical loader has had a very rapid and accelerated growth, until at present production of bituminous coal by mechanical means has reached an all-time high of approximately 46 per cent, and is still increasing. This rapid growth in the use of the mechanical loader has been supplemented by an increase. in mechanical cleaning. The importance of mechanical cleaning of coal was recogniaed many years before the mechanical loader was introduced. because of the impossibility of cleaning manually the sizes below 2 in.. and the increasing competition from other fuels. Utilization of mechanical loaders without nleclianical cleaning 011 the surface for at least one or more sizes is the exception, rather than the rule. One exception is a mine that employs caterpillar-mounted mobile loaders exclusively, and mines the entire seam without any selectivity, and yet loads and ships six grades of coal of the very highest quality without mechanical cleaning. Such a fortunate situation can exist only where mining conditions are ideal, where top and bottom are exceptional and there are no impurity partings, and where there is loader height. The conversion from hand loading to mechanical loading has definitely introduced many problems in the preparation plant of yesterday and in the modern streamline plant as well. Many of these problenis have been solved by good, sound, conscientious initiative on the part of the plant personnel, with minor expenditures; the solution taking the pattern of rearranging 2nd improving the equipment at hand. Other problems have caused, and are causing, considerable concern and difficulty. Large Impurities The removal of large quantities of large impurities from the lump coal, and their handling and disposal, is definitely a troublesome and costly problem. The cost of manually removing the impurities from the picking table alone, based on the actual recovered lump coal, can reach a cost of 42 cents per ton or more. In the design of future plants it would be wise to give this phase of preparation considerably more time and thought, particularly if the seam of coal contains one or more heavy partings and the mining procedure is all seam. This same caution applies to seams that may not contain heavy partings but have poor and heavy draw-slate top, which falls with the coal during the mining cycle. One of the more recent of the modern preparation plants has answered this problem by installing a rock crusher under the picking table in such a manner that the impurities can be diverted by gravity directly to the crusher. This reduces the

Jan 1, 1947

By E. C. Carris

The loading of bituminous coal mechanically was recognized about the year 1900, but during the following 28 years less than 5 per cent of the bituminous production in the United States was loaded by mechanical means. During the past 16 years, however, the usage of some form of mechanical loader has had a very rapid and accelerated growth, until at present production of bituminous coal by mechanical means has reached an all-time high of approximately 46 per cent, and is still increasing. This rapid growth in the use of the mechanical loader has been supplemented by an increase. in mechanical cleaning. The importance of mechanical cleaning of coal was recogniaed many years before the mechanical loader was introduced. because of the impossibility of cleaning manually the sizes below 2 in.. and the increasing competition from other fuels. Utilization of mechanical loaders without nleclianical cleaning 011 the surface for at least one or more sizes is the exception, rather than the rule. One exception is a mine that employs caterpillar-mounted mobile loaders exclusively, and mines the entire seam without any selectivity, and yet loads and ships six grades of coal of the very highest quality without mechanical cleaning. Such a fortunate situation can exist only where mining conditions are ideal, where top and bottom are exceptional and there are no impurity partings, and where there is loader height. The conversion from hand loading to mechanical loading has definitely introduced many problems in the preparation plant of yesterday and in the modern streamline plant as well. Many of these problenis have been solved by good, sound, conscientious initiative on the part of the plant personnel, with minor expenditures; the solution taking the pattern of rearranging 2nd improving the equipment at hand. Other problems have caused, and are causing, considerable concern and difficulty. Large Impurities The removal of large quantities of large impurities from the lump coal, and their handling and disposal, is definitely a troublesome and costly problem. The cost of manually removing the impurities from the picking table alone, based on the actual recovered lump coal, can reach a cost of 42 cents per ton or more. In the design of future plants it would be wise to give this phase of preparation considerably more time and thought, particularly if the seam of coal contains one or more heavy partings and the mining procedure is all seam. This same caution applies to seams that may not contain heavy partings but have poor and heavy draw-slate top, which falls with the coal during the mining cycle. One of the more recent of the modern preparation plants has answered this problem by installing a rock crusher under the picking table in such a manner that the impurities can be diverted by gravity directly to the crusher. This reduces the

Jan 1, 1947

By Charles R. Cavanaugh, John F. Elliott

The activity of nickel in liquid Pb-iVi alloys which are rich in lead was measured in the temperature region of 700° to 1100°C by means of the galvanic cell: The electrolyte used was stabilized zirconia. Tlze data were correlated using the a function, and a plot of the temperature coefficient aE/aT All subsequent calculations of the thermodynamic properties are based on these two functions. The activity, activity coefficient, and molar properties of mixing of nickel are reported. Nicke1 shows extreme positive deviations frorn ideality while lead shows a very slight positive deviation in the composition range studied The study of the activity of nickel in liquid Pb-Ni alloys reported herein was undertaken to explore the use of stabilized zirconia, an oxygen-ion electrolyte, with liquid-metal electrodes, and to obtain further information on the thermodynamic properties of the liquid binary Pb-Ni system. The cell The reversible electromotive force of the cell results from the difference in the chemical potential of the oxygen at the two electrodes: po, (left) - p~ (right) = -4E5 [I] The chemical potential of oxygen on the right is fixed by the activity of nickel in the solution and pure solid nickel oxide. That on the left is set by pure solid nickel in equilibrium with pure solid NiO. By definition: Since the chemical potential of nickel is related to the chemical potential of oxygen through the equilibrium constant for the formation of NiO from nickel and oxygen gas, the electromotive force of the cell is also expressed In this case, n is 2, E is the reversible potential of the cell, and 5 is Faraday's constant. The work of Kuikkola and wagnerl and Schmalz-reid2 has shown that the stabilized zirconia electrolyte is essentially an ionic conductor at the oxygen levels encountered in the experimental arrangement of the work, i .e., PG > 10-l7 atm. THE EXPERIMENTS The advantage of this type of reversible cell over those using a liquid electrolyte is the simplicity arising because the electrolyte also functions as one of the containing crucibles. A further simplification was the choice of the Ni (sat.)-NiO electrode as the standard. This permitted a ready check on the behavior of the electrolyte, as the potential of the cell must become zero when the right electrode becomes saturated with nickel, either because of a change of temperature or because of the addition of nickel to the electrode. It also permitted the potentials being measured to lie in the most satisfactory experimental range of 0 to 100 mv. Although it was not theoretically necessary, lead was included in the standard electrode as it assured good contact between the electrode and electrolyte. Cell Design. The general arrangement of the experimental cell assembly is shown in Fig. l(a) and the details of the cell itself are contained in Fig. l(b). The anode lead wire on the interior of the cell was connected to a coil of perforated sheet nickel. Within this coil were nickel oxide pellets which were held beneath the surface of the liquid Pb-Ni alloy. A disc of nickel oxide was held at the bottom of the external crucible (alumina) by means of the thermocouple protection tube. The nickel oxide disc and pellets were compressed dry at 10,000 psi and sintered at approximately 1000°C for an hour in air. A major experimental difficulty of reversible electromotive force cells with liquid electrodes is the selection of suitable materials for connecting

Jan 1, 1964

By G. S. Cole, G. F. Bolling

ThE exact type of fluid flow which occurs in a solidifying ingot is important in determining subsequent grain structure. This has been shown in studies of natural Convection" and of forced stirring or other disturbances of the melt."16 We shall explicitly argue that a complement to the existing natural flow in an ingot should be more effective than other types of flow in promoting the columnar-to-equiaxed transition. The ultimate effects of fluid flow upon structure is one of the topics of solidification that we have investigated in the alloy system Pb-Sb, under conditions simulating casting. In Fig. 1, the essential features of a bidirectional growth apparatus are shown; horizontal freezing from water-cooled faces within a low-thermal-conductivity lavite boat is a reasonable simulation of an ingot section. Details such as the furnace and thermocouples are omitted in order to show the location of four permanent. magnets, each with a pole separation of 21 in. providing a central field of about 1000 Gauss. When coupled with a dc current imposed through appropriate connections made at the cooled faces, a flow of fluid is produced as shown schematically. This technique described by Pfann and ~orsi" is ideal for our purpose since the flow indicated is the same as that we observe to occur naturally in this system. Components of 99.999 pct purity were used for study and all due precautions were taken in alloy preparation to avoid contaminants. Sections of the specimens were taken to ensure results representative of the interior as well as the surface of specimens. All proportions of equiaxed and columnar regions were measured by tracing the etched grain structures onto graph paper and simply counting squares. Four alloys were examined at superheats of 40" * 5°C and 100" * 9°C. Preliminary tests had shown that no appreciable enhancement of structure was obtained with magnetic field alone, so that this condition is not reported; it should nevertheless be noted that other configurations of magnetic field will reduce convection and thus enhance columnar growth.'8 For the tests reported the magnetic field was applied to a specimen by bringing the four preassembled magnets to a position 2 mm from an outer tube immediately after the ingot was poured. The dc current of 30 amps passed through the sample throughout the entire solidification cycle, resulting in a power dissipation of 9 w per sq cm of interface. This may be compared to the evolution of latent heat of approximately 18 w per sq cm. Table I contains the results of this experiment in terms of the total area ratio, equiaxed/columnar grains, as a function of the field interactions, solute concentrations, and superheats employed. The total structure of the ingot is seen to be most influenced when both the field and current are applied simultaneously; when current acts separately, little effect may be noted in spite of the heat supplied. In addition, the change in structure from the no field-no current case to the field-current condition is more pronounced at the higher superheat, and the higher the concentration of antimony. An example of the grain refinement, as well as the increased equiaxed zone, is shown in Fig. 2. It is now important to prove that there is indeed an increase in fluid flow due to the presence of the field-current interaction; this is done by temperature measurements in the liquid metal. Let us consider a bidirectional casting in which heat is applied to and removed from the system, in such a way that rate of solidification is zero.* When a sensitive thermocouple

Jan 1, 1967

By W. T. Stuart

THE increased demand for iron ore has necessitated a re-examination of ore-bearing lands on which the presence of water previously has indicated hazardous and expensive operating conditions. In view of the importance of iron ore production to the national economy and defense, the Ground Water Branch of the U. S. Geological Survey, in cooperation with the state of Michigan, began a study of mine drainage in the Iron River district in 1945, and later extended the work to the Marquette district. The purpose of these studies was to define the principles involved in the movement of surface and ground water toward the mined areas, with the hope that the information obtained in the research would lead to the development of methods of water control and to a reduction in the total mining costs. Not only are the direct costs of drainage increasing, but also the indirect operational costs of working a wet mine are becoming a larger proportion of the total mining costs. For some wet mines the direct costs of pumping and drainage may range from 35 to 40Ø per ton of ore produced, but the indirect costs due to handling wet ore and controlling the water may be five to ten times this amount. The methods of study were formulated as the work progressed, and inasmuch as they were the first large-scale studies of their kind, they should serve as a guide for the solution of similar problems in other mining areas. The Iron River district was chosen for a pilot study because in this district the longest records of mine pumpage and water-level observations were available, including, as they do, the records for the Homer mine of the M. A. Hanna Co., where pumping from surface wells began in 1930. The results of the first investigation by the Michigan Department of Conservation have already appeared." The first section of the report on a similar study of the Marquette district, which was started in 1948, will be published this year. Methods of Study In an effort to reduce the flow of water into the mine workings in the Iron River district, about 4500 gpm was pumped from the bedrock being mined and about 9000 gpm from the glacial overburden. In the Marquette district in the vicinity of Ishpeming and Negaunee, about 5000 gprn was pumped from the bedrock and about 4000 gpm was pumped from the glacial overburden. Where the water was pumped only from the bedrock, the rate of pumping ranged from a few hundred gallons per minute in the dry mines to many hundred gallons per minute in the wet mines. In each district, pumping from the overburden was localized on a few properties where costly pumping installations had been made and the expenditures for power had been large. In each district a comprehensive ground-water investigation was made of the whole area, involving the collection and interpretation of all the available data bearing on the source and quantity of water to be controlled. Although it is not the purpose of this paper to discuss the methods of making a ground-water investigation, it should be pointed out that a drainage study follows a pattern of engineering analysis that determines the occurrence, source, movement, disposal, and quantities of water involved. The investigation in the iron-mining districts of Michigan began with the construction of a map of the buried bedrock topography. Because the ground-water reservoirs occupy the low points in the bedrock basins, this map gives information concerning their areal extent, depth, shape, and degree of interconnection. The depth to water in the drillholes and wells indicates the altitude to which the ground-water reservoirs are filled, and the logs of the material penetrated in the drillholes and wells indicate the general character of the materials filling the reservoir. The slope of the ground-water surface indicates the direction of flow through the reservoir, the water movement being from the points of higher altitude to points of lower altitude. By analysis of the rise and fall of the ground-water levels in response to additions of water through recharge and to changes in the rate of discharge through pumped wells, estimates of the total quantity of water in storage and of the rate of flow through the reservoir

Jan 1, 1952

By M. R. Yalamanchili, C. A. Young, J. J. Kellar, W. M. Cross, J. D. Miller

Introduction Researchers have long speculated regarding the adsorption state of collectors on mineral surfaces. Only recently have analytical techniques become available that allow direct in situ analysis of adsorbed layers. With reactive internal reflection elements (IREs), Fourier transform infrared spectroscopy coupled with internal reflection spectroscopy (FT-IR/IRS) allows for unobtrusive investigation of the adsorbed layer (Harrick, 1979). This technique has been used both for the in situ identification of adsorbed species and for the direct calculation of collector adsorption density in real time from infrared spectral data (Miller and Kellar. 1988). The reactive mineral IRE serves both to internally reflect the infrared light and to act as a substrate at which collector adsorption can be monitored. Shown in Fig. I is a schematic of light being internally reflected in an IRE. As the light is totally reflected at the interface, an evanescent wave propagates a short distance (typically a few microns) away from the IRE, and sampling of the interfacial region occurs. Because of multiple internal reflections, great sensitivity can be obtained. Flotation systems for which this method has been demonstrated include CaF2/oleate, Al2O3/dodecylsulfate, CaCO3/oleate, ZnS/xanthate and KCI/octylamine (Miller and Kellar, 1988; Kellar et al., 1989, 1990; Miller et al., 1990). Of particular interest to flotation chemists is the conformational behavior of the alkyl chain of adsorbed collector molecules. In the simplest sense, conformation can bethought of as the relative flexibility of the hydrocarbon chain caused by rotations about carbon-carbon single bonds. The flexibility is described by the amount of gauche/trans conformations in the alkyl chain. Figure 2 shows examples of gauche and trans conformations (rotational isomers or rotamers) in a hydrocarbon chain. These two conformations are observed when the terminal methylene groups in any four-carbon subchain are on the same side (gauche) or opposites sides (trans) of the plane of the middle carbon-carbon bond. A gauche conformer (rotamer) is thus a state of maximum potential energy, whereas a trans conformer is a state with minimum potential energy. The difference between these states has been found to be approximately 0.5 to 0.8 kcal/mole (Mead et al., 1986). The relative number of butane molecules present as gauche conformers with respect to trans conformers can be calculated from the Boltzmann equation (Mead et al., 1986). At 25° C approximately 66% of the butane molecules are trans rotamers. [ ] However at 100° C, only 33% of butane molecules are trans rotamers. Exposing the hydrocarbon chain to a polar, rather than an a polar, medium should also cause an increase in the number of gauche butylene groups in a hydrocarbon chain, although this effect has been difficult to observe experimentally (Mead et al., 1986). Forming a crystalline hydrocarbon is equivalent to decreasing the temperature, which greatly increases the amount of trans butylene groups present in the chain. From the preceding discussion, a picture of the solution species of concern can be developed. The collector monomer should exhibit the greatest number of gauche rotamers and most likely will look crumpled or balled-up to reduce the surface area in contact with water. The micellar form is expected to be aggregated, with the hydrocarbon chain existing in a less polar environment. These characteristic conformational features have been examined by FT-IR spectroscopy for various liquid phases of alkanoic acids (Umemura et al., 1981; Cameron et al., 1982a; Yang et al., 1986; Wong, 1987; Wong and Mantsch, 1983; Cross et al., 1992), phospholipid membranes (Fringe Ii, 1980; Casal and Mantsch, 1985: Wong et al.. 1988;

Jan 1, 1994

Investigations of the Mineragraphic Section; Commonwealth Scientific and Industrial Research Organisation, have included most of the known stannite-bearing ores in Australia, and have revealed several new occurrences of this relatively uncommon mineral. They provide information about its paragenesis, and its possible effect on tin recovery, that may be of general interest.Several of the investigations used in the preparation of this paper, were made in the first instance by pr. F. L. Stillwell or in collaboration with him.CASSITERITE-SULPHIDE ORES IN NORTH-WEST- TASMANIA Stannite is a minor component of most of the cassiterite sulphide ores of north-western Tasmania. These include the orebodies of Mount Bischoff, the Cleveland mine, Moina, the Stanley River district, Renison Bell, and the Heemskirk-Zeehan district, and form a well defined metallogenetic provence which is related to the Devonian granites of this part of Tasmania.In these ores mineralisation began. with deposition of cassiterite, a little wolfram, and quartz, topaz and tourmaline. With falling temperature, deposition of cassiterite ceased and arsenopy-rite, pyrite, and especially pyrrhotite, formed in abundance, tending to give massive sulphide ore. A little chalcopyrite; stannite, sphalerite and native bismuth accompanied the pyrrhotite. Deposition of quartz ceased after the pyrrhotite, was formed, and the later-formed nonsulphide gangue consists chiefly of carbonates and fluorite. With, the advent of the carbonates the pyrrhotite was altered to fine-gained intergrowths of marcasite and pyrite. Excess iron from the pyrrhotite entered the intergrown carbonate, or was precipitated as magnetite. Some solution of the cassiterite occurred at this stage, the tin being redeposited chiefly as stimnite replacement rims around the residual cassitellrite grains. Varying, but small, amounts of sphalerite, galena, tetrahedrite and silver minerals were depoSited at this stage, bringing the mineralisation to a...

Jan 1, 1951

By M. A. Schimmelpfennig, A. D. S. Gillies

M.J. McPherson Having worked on the thermodynamics of air/liquid-water mixtures passing through the surface fans of deep mines, I find this paper of great interest and congratulate the authors on producing it. There are two matters, however, deserving discussion. First, the authors have described the classical theory of fog formation with fogging occurring at "supersaturation." In fact, the process of fog formation begins well below 100% humidity. The more strongly hygroscopic nuclei in the atmosphere will attract water molecules and begin to grow at a relative humidity perhaps as low as 70%. The process is a dynamic one with both condensation and evaporation taking place throughout the mixture on microscopic liquid surfaces. As saturation is approached, the rate of condensation accelerates rapidly producing the familiar reduction in visibility. Hygroscopic nuclei are present in all natural atmospheres and under the appropriate conditions of pressure and temperature, will produce clean fogs. However, if the air is polluted by particulates from combustion or other processes then the resultant coagulation with growing liquid particles may produce dense (and sometimes photochemical) smogs. It is this process that is likely to occur in underground mines when moist air is cooled below dew point. Second, the authors have summarized very well the individual measures that might alleviate the problem. In particular, I agree that neither heating nor refrigerating the air, by themselves, provides a satisfactory solution. However, there is a combination of these that provides a neat and effective control of fog formation. This involves a small, self-contained refrigeration unit within a duct but without the usual external heat rejection facility. The air is cooled below dew point and, hence, dehumidified on passing over the cold evaporator coils. The heat from the condenser is rejected back into the air downstream from the water eliminator, as shown in Fig. 1. The duct configuration can be designed to create good mixing at the outlet. I have used a climatic simulation program to illustrate the effect, assuming a 500-m (1,640 ft) long airway of cross section 60 m2 (645 sq ft), an airflow of 9 m3/s (318 cu ft per sec), inlet conditions of 19/19.25°C (66/67°F) wet bulb/dry bulb temperatures, a virgin rock temperature of 17°C (63°F) and typical rock thermal properties for a hard-rock mine. I have also assumed that 10% of the rock surface is wet. Figure 2 shows the variation in temperatures along the airway if no measures are taken. The relative humidity remains close to 100% and condensation will occur throughout the length of the airway. Before any such installation is designed, the exercise must, of course, be repeated for each location with accurate data. However, this example demonstrates the potential of the system. The idea is not new - the principle is sometimes used in air-conditioning plants for buildings. Figure 3 shows the effect of removing 30 kw of heat by evaporator coils sited 40 m (131 ft) along the airway and rejecting that heat (plus another 10 kw of compressor and fan power) into the air at 60 m (197 ft). Condensate water is produced, at a rate of 0.45 L/min (0.12 gpm). The result of this sequential cooling/dehumidification/heating process is to separate the wet and dry bulb temperatures along the length of the airway. The relative humidity increases from 80% at the duct outlet to 92% at 500 m (1,640 ft). The airway is maintained free from fog.

Jan 11, 1983

By J McNee

Pike River Coal Limited (PRCL) is developing the Pike River Coal Mine in the Paparoa Ranges of New ZealandÆs South Island. The mine is being developed to extract a coking coal deposit of the Brunner Seam, some 46 km northeast of Greymouth, using a combination of continuous miners, road-headers and hydraulic extraction.   The mining area is located within Department of Conservation (DOC) land and is adjacent to the escarpment of the Paparoa Range and the Paparoa National Park. The mine will use its elevation advantage to hydraulically flume coal from the working faces to the pit bottom area where it will be slurried to approximately 35 per cent density of solids and pumped down a slurry line to the coal prep plant some 10.5 km down the Pike River Valley. The coal will be sold on the export market as a high quality coking coal for international steel making.   PRCL faces significant challenges to achieving the goal of cost effective production. The remoteness, high rainfall (greater then 6 metres per year on average), temperature variation and restrictions on access to this subalpine environment have driven the project to develop some distinctive solutions. These include the establishment of survey control in such a difficult environment with vertical and sub-vertical rock faces, significant vegetation and steep slopes by using helicopter survey, aerial photography and LIDAR (Light Detection And Ranging) aerial survey. PRCL has also commenced designing the placement of the main ventilation fans in an underground chamber in the stone drive.

Jan 1, 2007

By A. E. Dwight, P. A. Beck

A search was made for ordered phases of AB3 composition in various combinations of Ti- and V-group elements with CO-and Ni-group elements. Three new TiNi3-type phases ZrPd3, HfPd3, and HfPt3 were found. In addition, twelve new Cu3Au-type phases TiRh3, Tilr3, ZrRh3, Zrlr3, HfRh3, Hflr3, VRh3, VIr3, CbRh3, Cblr3, TaRh3, and TaIr3 were also found. The lattice contraction for all three structures considered increases with increasing relative size of the A atom, suggesting that it is mostly the A atom that cont~acts. It was noted that, for the same radius ratio the lattice contraction is larger when the A atom is Ti than if it is Cb OY Ta. It is well known that elements or disordered solid solutions, which have structures with spherical close-packing, may be described in terms of various stacking schemes of close-packed layers. Stacking of the type abab corresponds to the hexagonal close-packed structure, and stacking of the type abcabc corresponds to the face-centered-cubic structure. In binary alloys of the first, second, and third long period transition elements various AB3 phases occur with close-packed ordered structures. It was observed that these ordered structures also may be described by suitable stacking of close-packed ordered layers, Fig. 1, as first shown by Laves and Wallbaum for TiNi3.' It is clear that the units of translation in such a close-packed layer consist of four atoms, one of which (black circle) is atom A and the three others (empty circles) are atoms B. Because of the alternation of A and B atoms in every second row of each layer, the unit-cell dimension in the layer is equal to the sum of the diameters of atoms A and B: a0 = 2(rA + rB). Stacking of such layers in the sequence abab results in a hexagonal close-packed structure of the MgCd, type. The unit-cell dimension in the basal plane is approximately double of that for the disordered hexagonal close-packed structure, but in the direction of the hexagonal axis it is about the same, so that 2co/uo = 1.63 in case of spherical close-packing. Ordered hexagonal close-packed structures of this type were found to occur in MoCo3,2 WCo3,, and UPt, .4 When the ordered layers shown in Fig. 1 are stacked according to the scheme abcabc, the resulting ordered structure is of the AuCu, type (cubic). Structures of this type were found to occur in TiPt3,5 CrPt,,' CrIr,,' and URu, .4 Finally, the stacking scheme abacabac of the same ordered layers results in a hexagonal close-packed structure of the TiNi3 type.' In this case, the unit-cell dimension is doubled not only in the basal plane, but also in the direction of the hexagonal axis, so that co/ao = 1.63. Structures of this type were found to occur also in TiPd3,5 ZrPt,," and UPd,.4

Jan 1, 1960

By S Jahanshahi, D R. Swinbourne

The classical metal-slag-gas equilibrium technique was used to study the thermodynamic activity of cobalt, iron and their oxides in iron silicate based slags containing under controlled oxygen potential (3.70 x 10-8 to 2.95 x 10-7 atm) at 1573 K. The measured activity of cobalt oxide in FeOx-25 wt per cent SiO2 slags showed positive deviation from ideal behaviour for melts with up to ten wt per cent CoO. At higher silica contents, the behaviour became closer to ideal and in accord with previous studies on silica saturated slags. The activity coefficient of FeO in these slags had virtually no dependence on the CoO content. Partial substitution of silica by lime resulted in an increase of the activities and activity coefficients of CoO, FeO, Fe2O3 and Fe3O4. The results indicate that saturation of the slag with a magnetite phase occurs at CaO contents of five wt per cent and higher. Phase equilibria studies SiO2-FeO-Fe2O3-CaO slags containing cobalt were also carried out using the drop-quench technique. Results from these experiments confirmed the formation of a magnetite solid solution containing about three wt per cent CoO at lime contents of five wt per cent and higher at 1573 K and 2.9 x 10-7 atm of oxygen.

Jan 1, 2000

By Sidney Diamond, Charles Wert

The anelastic behavior of Ni-C alloys of nominal 0.5 wt pct C has been determined over a wide temperature range. The most prominent damping effect, that due to the presence of C-C pairs, was measured both above and below the Curie temperature. The effect on diffusion of the C-C pairs by magnetic spin ordering is deduced to be very small. The diffusion coefficient for C-C pairs in nickel is given by the expression ThE solid-state diffusion of both interstitial and sub-stitutional solutes in ferromagnetic solvents has been the subject of a number of investigations. Measurements of the self-diffusion of iron,"' the diffusion of nickel1,4 gold,"1 and cobalt4 into iron, the diffusion of vanadium in an Fe-V alloy,' and the diffusion of cobalt and nickel in Co-Ni alloys9 show an unusual behavior. In both the ferromagnetic and paramagnetic regions, far removed from the Curie temperature, the diffusion coefficient, D, obeys an Arrhenius relation. However, in the ferromagnetic region D is markedly lower than would be expected from an extrapolation of D from the paramagnetic region; this results in an increase in the activation energy in the ferromagnetic region. The cause of this effect for self- and substitutional diffusion is uncertain. Since substitutional diffusion is presumed to proceed by the vacancy mechanism, it has been variously suggested that the increase in activation energy below the Curie temperature is due to one of the following causes: 1) an increase in the energy of formation of a vacancy because of local demagnetization around the vacancy,2,3 2) a decrease in vacancy mobility in the ferromagnetic state,' or 3) an effect on the entropy of motion of a vacancy in the ferromagnetic state.5 Quite another explanation for the observed effect has been proposed by Borg.7 The diffusion coefficient is a function of the elastic constants of a metal. Since the temperature dependence of the elastic constants often changes at the Curie temperature, the temperature dependence of D might be expected to undergo a universal change in the vicinity of the Curie temperature. The magnitude of the change in D would, of course, depend on the magnitude of the change in the elastic constants. One might attempt to differentiate between vacancy effects and elastic effects by making measurements on interstitial alloys, in which vacancy effects play no role. Some measurements of this type have been made; this paper reports additional observations. Measurements of the diffusion of carbon in a Fe by a tracer technique8 and of the diffusion of carbon in a Co and in Co-Fe alloys by a decarburization method9 reveal a small effect, if any, on D of the magnetic change at the Curie temperature. If the effect of spin ordering is only to alter the parameters controlling formation or mobility of a vacancy, interstitial diffusion should indeed remain unchanged through the magnetic transition, as these measurements imply.

Jan 1, 1968

By A. J. Hendron, G. Mesri, R. M. Semple

Squeezing ground conditions in hard-rock tunneling are associated with fault zones containing brecciated rock and gouge. Gouge is a stiff clay-like soil that exhibits a propensity to creep. The ground loads applied to tunnel supports in squeezing ground are known to be significantly time dependent. Accordingly, an experimental and analytical study is presented that deals with soil creep and its application to the prediction of tunnel support requirements in squeezing ground conditions. Relatively undisturbed samples of fault gouge obtained from Straight Creek tunnel in Colorado and Pacheco tunnel in California are classified as very stiff to hard clays of low plasticity. Constant-load undrained triaxial compression tests are performed on these materials. A simple, three-parameter creep equation is developed that adequately describes the observed deformation of fault gouge with respect to applied stress and time. The equation is shown to fit existing creep data of various soil types. The creep equation is used to modify an existing continuum-mechanics solution to the time-dependent behavior of unlined and lined cylindrical openings in a creepsensitive medium under a hydrostatic state of stress. Assuming properties for the medium that are representative of the fault gouge materials tested, parameter studies are performed for unsupported and supported tunnels in squeezing ground. The analyses permit estimates to be made of the steel set supports required for tunnels at different depths in various squeezing ground conditions.

Jan 1, 1974

By J. M. Musadaidzwa

Skorpion Zinc is located 25 km north-west of the small settlement of Rosh Pinah in southern Namibia. Commissioned in early 2003, Skorpion Zinc became the first mine-to-metal operation to commercially apply a purely hydrometallurgical process route to exploit a zinc oxide orebody. The novel technology, known as The Modified ZincexTM Process patented by Tecnicas Reunidas, comprises sulphuric acid atmospheric leaching, zinc solvent extraction (SX) and electrowinning (EW) to produce London metal exchange (LME) Special high grade (SHG) zinc. Forming the core of the process, the SX step has thrived in its role as a barrier to impurities and also in the upgrading of the pregnant liquor solution (PLS), converting it into a loaded electrolyte (LE) sufficiently rich and pure for EW. Against this successful run, a number of challenges have, however, been encountered in SX due the emergence of upset conditions largely emanating from upstream processes. This paper outlines some of the major deviations that have beset the SX process in its first five years of continuous operation. Impurity excursions, temperature depressions, changes in phase continuity, excess aqueous entrainment, the effect of colloidal silica and the accumulation of rare earth elements on the organic phase will be discussed in detail. Keywords: skorpion zinc, solvent extraction, the Modified ZincexTM Process (MZP) DE2HPA, aqueous entrainment (AE), loaded electrolyte (LE), standard liquid validation (SLV) test, organic continuity, aqueous continuity (AC), electrowinning, colloidal silica, phase disengagement time (PDT), rare earth elements (REE).

Jan 1, 2009

By D. Boufounos

The large open pit areas of surface mining as well as the huge quantities of residues generated during the digestion of bauxite with sodium hydroxide solution to produce alumina are considered as the most important environmental problems associated with the exploitation of bauxites. Aluminum of Greece, which is the only aluminum refinery in the country, located in Agios Nicolaos, Paralia Distomou, Viotia, produces almost 680.000 tones of bauxite residue annually which is pumped through pipes from the refinery to the sea bed of Antikira gulf. In order to avoid any kind of environmental problems related to this disposal method and to reduce the total volume of bauxite residue disposed of in the environment, Aluminium of Greece investigates several alternatives for bauxite residue utilization. In this framework, it also examines the potential use of bauxite residues as a filler in abandoned mining open pits. Bauxite residues are mainly composed of fine particles of silica, aluminum, iron, calcium and titanium oxides and hydroxides. Furthermore, the material presents low hydraulic conductivity, slightly higher than the limit posed for low permeability layers by the EC landfill directive. Based on these properties the dry disposal method was selected for disposing bauxite residues in mining open pits since it has many advantages such as reduced overall disposal cost, effective use of land and minimum environmental impacts. The results obtained for this method, which is investigated at demonstration scale, are presented in this paper.

Jan 1, 2005

By John A. L. Dr. Campbell, James W. Haskew, F. Hoy Lee, Elliott P. Dr. Doane

Emissions of particulates, unburned hydrocarbons, nitrogen oxides (NO[ ]) and carbon monoxide (CO) from diesel engines are of concern in mines, particularly underground mines. All these undesirable products except NOx are the result of incomplete combustion in the cylinders. Various approaches to achieving more complete combustion in diesel engines have included different fuel compositions, use of catalysts, fuel additives, engine modifications, and oxygen-enriched intake air. The present study shows that injecting minute quantities of primarily platinum group metal catalysts into the intake air of a Deutz/MWM D916-6 mine diesel engine substantially reduces emissions in the exhaust. The catalyst injection system, which was developed by National Fuelsaver Corporation (Robin. 1981), transfers catalyst compounds in solution to a stream of air bubbles by a process called Bubble Fractionation (Lemlich et al.. 1966, 1968. 1970). The amounts are so minute that concentrations in the engine exhaust should be well below OSHA/NIOSH Time Weighted Average (TWA) exposure limits at steady state, a fact that was confirmed by analysis of collected particulates in the exhaust. When the catalyst injection was used along with a pleated paper filter to remove exhaust particulates, the filter operating life was shortened greatly. Therefore, this system is not recommended for use on diesel engines equipped with a water scrubber and a filter. It does offer a practical and relatively economical way of reducing exhaust emissions from other diesel engines, such as those in outby mine service

Jan 1, 1995

By G. R. Speich

A cellular precipitation reaction in which cells consisting of an Ni3Ti (DO24) phase and austenite are formed has been studied in an austenitic Fe-30 Ni-6 Ti alloy. The variation of the growth rate and interlamellar spacing of the Ni3Ti cells with temperature has been determined m the range 400" to 975°C; the interlamellar spacing is proportional to the degree of undercooling; the growth rate can be expressed by an equation of the form G = K?T)2 exp(-Q/RT). The habit of the Ni3Ti lamellae is (001)Ni3Ti (111)y;[010]Ni3T2 [010]y. An almost perfectly coherent interface is formed between Ni3Ti lamellae with this orientation rela -tionship and the intervening austenite. This first Ni3Ti cellular product is subsequently consumed by a second cellular reaction of much coarser spacing. CELLULAR precipitation reactions have been studied in copper-base,1,2 Au-Ni,3 pb-sn,4 and iron-base ferritic5,6 solid solutions, and this mode of precipitation has been treated theoretically by smith," Turnbull,8,9 cahn,10 and more recently by bohm.11 In the case of substitutional austenitic iron-base alloys little or no data are available, Cellular precipitation reactions are well known in austenitic nickel-base alloys12,13 but usually these reactions do not proceed to completion because of general precipitation occurring in the matrix, and they have not been studied in detail. Precipitation from an austenitic Fe-30 Ni-6 Ti alloy was studied as part of a larger investigation of the mechanisms of precipitation from substitutional iron-base alloys. This alloy, austenitic at high temperatures, decomposes at lower temperatures by a double cellular precipitation reaction. The first decomposition product consists of alternate lamellae of an Ni3Ti(DO24) phase and austenite. The reaction proceeds to completion, consuming all of the original austenite. This first cellular product is subsequently consumed by a second cellular reaction of much coarser spacing. The first cellular reaction was studied in detail by light and electron microscopy, hardness measurements, and by X-ray and electron diffraction. Interlamellar spacings and growth rates were measured during isothermal aging in the range 400" to 975°C. The orientation relationship between the Ni3Ti and austenite lamellae was determined and indicates that an almost perfectly coherent interface exists between the two phases. This first Ni3Ti cellular reaction is of particular interest because it occurs over such a wide temperature interval. This allows cellular growth rates and interlamellar spacing data to be obtained for much larger degrees of undercooling than reported hitherto. MATERIALS AND EXPERIMENTAL PROCEDURE The Fe-30 Ni-6 Ti alloy was prepared from electrolytic iron, Mond nickel shot, and sponge-purity titanium* by vacuum melting in a zirconia crucible

Jan 1, 1963

By Hugh Rose

JAY A. CARPENTER, Tonopah, Nev: (communication to the Secretary*).-This description of the Santa Gertrudis mill is of great interest to the operators of similar silver mills in Nevada. At the San Francisco meeting last September there were two excellent papers presented on Nevada silver mills; one by A. H. Jones on The Tonopah Plant of the Belmont Milling Co., and the other by E. E. Carpenter on Cyaniding Practice of the Churchill Milling Co., Wonder, Nev. At the same meeting, I presented a paper on-Slime Agitation and Solution Replacement Methods at the West End Mill, Tonopah, Nev., covering this .particular feature of our milling practice. A comparison of the data presented in these four papers is interesting in that, while the general design and practice is much the same in all cases, there is a wide difference in the design and practice in the various departments of 'the mills. It is to be regretted that Mr. Rose did not round out. this excellent article by following Mr. Jones's and Mr. Carpenter's' lead in giving the average gold and silver content of the ore milled and the resulting tailing, with the consumption of chemicals and the? cost of milling. The practice of the Santa Gertrudis mill in the use of ?cyanide and zinc offers an interesting comparison with that of the Nevada mills, and a discussion of this point may bring out the reasons for the differences that exist.

Jan 12, 1916

By Henk Dijkman

Existing metallurgical operations can be optimized by implementing engineered bioreactor systems in the process configuration. For instance, metals can be recovered safely and economically from process and waste streams using biogenic sulfide. This paper focuses upon possible applications of high rate biotechnology in metallurgy and mining. Metal recovery from liquid streams (process bleed streams, leach water, waste streams), integrated removal of (fugitive) SO2, treatment of acid blowdown and other options will be described. Practical examples are given. A large-scale application of biotechnology at Pasminco's Budel Zink refinery is described. Here, acid plant blowdown is treated together with electrolyte magnesium bleed. Concentrated zinc sulfide (10 tpd) is produced biologically, eliminating the production of gypsum and closing the refinery sulfur cycle. Recovery of metals from solution at Kovehute Pribram in the Czech Republic is the second practical example. In this case, H2S is produced on-site for metal removal from an alkaline slag dump leachate. At the Caribou mine in New Brunswick, Canada, acid mine drainage is treated with biogenic sulfide. This plant is situated upstream of a lime neutralization plant. As a result, reusable ZnS is produced, the volume of the sludge (gypsum and hydroxides) from the lime plant is reduced by 50%, the sludge is free of heavy metals and the final effluent concentration of heavy metals is in the ppb range. In the second phase of this project, metals will be recovered from stored tailings, resulting in significant revenues.

Jan 1, 2002