Search Documents

By Thomas Jenning, C. M. Keithly

"INTRODUCTION This report is one of a series. 4. 5. 6/ concerned with presenting historical development, and operating data on secondary-recovery projects in various States to stimulate interest in sound secondary-recovery programs. Preceding reports in this series have dealt exclusively with descriptions of and results obtained by water flooding in three states, but no recent publication of comparable purpose describes gas-injection 7/ practices. The authors intend to present material relevant to the development and operation of gas-injection projects in Illinois, with particular emphasis on those producing from oil-bearing horizons that had been depleted to a point near the economic limit of operation by past oil-recovery methods.Most operators realize that the energy expended on the movement of fluids through gas-expansion- or gas-cap-type oil reservoirs to producing wells must be supplemented to attain maximum recovery of the oil present. Under favorable conditions, many operators choose to maintain oil-propulsive forces at or near their original magnitude by injecting extraneous fluids into a reservoir or recycling produced fluids early in the life of a field. More common, and less desirable, is the practice of replenishing these forces after primary producing methods become unprofitable. The lattes practice has been adopted in many stripper fields in Illinois and most of the oil-producing States during the last 40 years, but other old oil fields, and oil properties within those fields which were partly exploited by secondary--recovery methods, also may offer favorable opportunity for further development. To encourage and, aid operators in the development of gas-injection projects in the old oil fields of the United States, four projects have been described in detail in this report."

Nov 1, 1944

By Denby B, Miles N. J

The underlying theory behind the construction of an on-line size analysis system is described together with an introduction to the Artificial Intelligent techniques that it is founded on. Previous systems based on more traditional technology such as edge detection and dilation algorithms have been restricted by the significant processing power they require, this has resulted in the production of systems with either reduced functionality or severe hardware requirements. A neural network approach offered a new perspective to the problem of size analysis; the ability of a network to learn and recognise subtle patterns in training data before on-line processing is initiated opened up the possibility for the production of a fully functioning practical system. The format of the training data had to be carefully analysed prior to its implementation in a neural network as the capability of a neural network solution depends as much upon a suitable data preparation as it does on the system architecture. To facilitate experimentation with various profile quantification techniques such as fourier and fractal analysis an Image Profile Analysis System was constructed (IPAS) in software on a personal computer. The IPAS system was produced with the aim of pre-processing image data to create data sets for experimenting with external neural network packages. The system allows the analysis of both real images obtained by image capture and simulated images created by an in-built in simulator. A measurement comparison scheme is also included together with a case study concerned with the frequency analysis of simulated images. The power of neural networks combined with the data compression provided by profiling removes the need for direct measurement of individual particles. This has obvious implications on the level of hardware necessary, and ultimately the expense of a stand alone system. The extrusive nature of data collection via an image analysis system will also permit simple installation of a shipped system; eliminating any requirement for interference with existing machinery.

Jan 1, 1995

By P. C. Garg

"IntroductionThe Central Mine Planning and Design Institute (CMPDI) of India, started planning the extraction of thick seams highly susceptible to heating in 1977by the French method of sub-level caving and/or multi-slicing. Nitrogen flushing was proposed for inhibition of heating by the author in one such project - the Kotadih colliery.Inhibition of heating was unheard of in the Indian coal industry before 1977-78. The usual practice was to seal off a district or a part of the mine or the entire mine when spontaneous heating occurred. With very little equipment in a normal bord and pillar district and a low production rate, the financial loss in capital assets and in production did not warrant any serious thought for inhibition of spontaneous combustion. With the planned advent of longwall mining, particularly sub-level caving, with heavy capital investment as well as high production potential, the sealing of a longwall face due to spontaneous heating could not be considered an appropriate solution.Principle of Inhibition of SpontaneousCombustionFrench engineers have established that a fire will not break out when oxygen is 15% or lower in the general body of the air. However, once a fire starts, the percentage of oxygen has to be reduced to 2% - 4% to extinguish it. It is this principle which has been used at Blanzy Coalfield in France to inhibit heating and it is claimed that this has retrieved the integral sub level method of mining. Nitrogen infusion has been used in Frence since 1978 to keep the oxygen content below 14% in the goaf."

Jan 1, 1987

Nowadays, fully encapsulated rockbolts have become a key element in the design of ground control systems. The main reason is that they offer high axial resistance to bed separation. In this research, the load transfer capacity of a fully grouted bolt is evaluated analytically in an elastoplastic rock mass condition. The research considered the effect of bolt end-plate on load transfer capacity. Bolt and surrounding materials were assumed to be elastic and elastoplastic materials respectively. The load transfer mechanism of a fully grouted bolt is a function of parameters such as bolt length, shear stiffness of interfaces, in situ stress, presence of face-plate and distance along the bolt. These factors were analytically evaluated. Finally, the load along the bolt was predicted in different surrounding rock mass characteristics.

Jan 1, 2011

By C. W. Washburne

Recently, Messrs, Mills and Wells1 published a thorough chemical study of the waters associated with oil in parts of the Pennsylvania, Ohio, and West Virginia region. Many of their conclusions are of general application and the writer wishes to discuss some of these. Messrs. Mills and Wells show that the composition of the deep brines oi the Appalachian fields is such as would be produced by the evaporation of sea water and the precipitation of sodium chloride, combined with reactions with hydrocarbons and other substances. The brines are altered, also, by considerable mixing with meteoric water. They give good reasons for believing that the concentration of the brines was produced by evaporation in the rock pores induced by migrating gas, much of which probably escaped to the surface of the ground. This hypothesis was considered by the writer in a former paperJ2 in which main stress was laid on a second hypothesis, that the excess of chlorine in the deep brines may have been due to the entrance of solutions rich in magnesium and calcium chloride which ascended from a deep, possibly intratellurie, source. Messrs. Mills and Wells present good arguments for the first hypothesis. Underground evaporation by ascending gases probably will be accepted as the best available explanation of the concentration and composition of deep well waters. They have not considered the possibility that salt waters in deep sands may be concentrated by the diffusion of water vapor through gas into shale. The writer has given reasons3 for believing that capillary forces concentrate gas and oil in the larger openings of rock, such as the pores of sandstones embedded in shale. The gas underground must be nearly saturated with water vapor at all times, because it always is in contact with the interstitial water of enclosing shales and of the sandstone. Experimental studies of soil moisture have shown that approxi-

Jan 1, 1921

By Joseph Singewald

THE problem of the utilization of the low-grade red iron-ores has peen before the iron-mining industry of the South for several decades. the experiments by W. H. Coghill1 of the U. S. Bureau of Mines to determine the degree of liberation of minerals in the Alabama low-grade red iron-ores after grinding interest the writer very much because 10 fears ago, while a member of the U. S. Bureau of, Mines, he experimented similarly on the same ores using a heavy solution .2 Extensive experiments were made in the nineties by W. B. Phillips3 in association with H. A. J. Wilkens and H. B. C. Nitze. The ores were rushed to pass 15 mesh and were separated by magnetic machines into concentrates, middlings and tails. The experiments were made with carload lots in an experimental mill. Most of the ores tested, however, were soft, whereas the main problem is the utilization of the low-grade hard ores. Phillips gives the results of only four tests of hard ores; two of these are of self-fluxing ores of the grade now utilized and two of ower grade and less amenable to concentration than the average low-grade ore that underlies the self-fluxing ore of the Big Seam. The average of these least favorable samples shows the production, from an ore analyzing 32.30 per cent. Fe, 10.34 per cent. CaO, 33.40 per cent. insoluble, of a concentrate with 43.82 per cent. Fe, 8.90 per cent. CaO, 18.48 per Sent. insoluble with a ratio of concentration of 2 and an iron recovery of 39.2 per. cent. The grade of this concentrate compares favorably with the average grade of washed brown ores of the district which is given by Burchard4 as 45 per cent. Fe, 14.6 per cent. Si02. The slightly lower iron

Jan 2, 1927

By R. B. Tippin, J. S. Browning

The feasibility of multistage heavy liquid cyclone beneficiation of spodumene was successfully demonstrated in this investigation. The indicated recovery for the multistage circuits was mathematically estimated as continuous test runs would be necessary to determine the true influence of a middlings recycle. In the three-stage circuit, both the concentrate analysis and spodumene recovery exceeded 90%. The two-stage circuits were unable to simultaneously yield an acceptable produce with a satisfactory recovery. With the Nation's growing industrial mineral requirements, the U.S. Bureau of Mines has undertaken the task of investigating new mineral dressing techniques and improving the existing concentrating methods of ore beneficiation. One such project is the gravity concentration of minerals using heavy liquid separation (HLS).1-3 Heavy liquid separation is based on the simple principle that a material, whose specific gravity is less than the density of a solution, will float on top of the liquid and a material with a greater specific gravity will sink. Heavy liquid separation techniques were developed in the laboratory over half a century ago but the process has yet to be commercially adopted. In the past, commercial operations have failed because of numerous problems.4 Industrial interest has recently been reactivated because of engineering advances. The number and quality of the heavy liquids suitable for mineral processing has increased while the cost has sharply dropped. New and improved liquid recovery systems5,6 are under consideration with present emphasis on 1) solvent extraction, 2) thermo-evaporation, and 3) water washing. The toxicity of the heavy liquids7 presents a problem, but throughout the chemical and mining industries, many similar hazardous materials are safely handled. A distinct advantage of using heavy liquids is its ability to provide a near perfect separation of fine-sized mineral particles even when the specific gravities are close. Effective separations have been made on minerals down to 200 mesh and with a density

Jan 1, 1968

By C. B. Manula, R. L. Sanford, R. A. Rivell

This report describes the development and application of a rail haulage simulator that is readily adaptable for the analysis of a wide variety of operating problems. Various gaming, options have been integrated into the model structure which permit trial and error solutions from a computer terminal prior to capital committment in the actual operation. The high level of information retrieval available allows engineers and managers to develop production data which fit individual needs. In this report, emphasis was placed on the problem of organizing and performing the sequence of operations that are necessary to accomplish a complete mine materials handling simulation. Here, the Rail Haulage Sub-assembly was linked to the Production Sub-system to mine and move coal from seven operating sections to the intermediate and main-line track. The analysis was devoted to the problems associated with how the operating system performs and what alternatives were available to minimize idle times and hence increase productivity. In order to have some objective means of evaluating which of the alter- native methods for production was most appropriate, the choice was to replace the intermediate track with belt conveyors. Since the attempt here was to demonstrate model flexibility and not to establish the goals or trade-offs between computing objectives with which systems judgement must contend, no further alternatives were tried. This is left to management with the data and a problem to solve. Rail haulage simulation is not new, and several, operationally tested models are being used in practice (Bucklen, et. al., 1968).

Jan 1, 1974

By Warren A. Sinsheimer

ProbDly there has never been a year during which the petroleum industry expended so much effort as in 1929 in an attempt to rectify its ills. Eventually good will undoubtedly result, but as yet there have been no marked changes from the unhappy conditions familiar to all. Throughout the year remedies were sought that would cure the long-existing troubles of overproduction and waste. Proration of production and voluntary curtailment of output, for a short time considered the means for stability, not only failed but contributed to further waste and created a false sense of security. It encouraged a high rate of field development, weakened the economic structure by excessive development of newly discovered reserves and absorbed large sums of capital yielding meager or negative return. The manufacturing of gasoline by refiners without regard for market requirements furthered the unsatisfactory condition by falsely stimulating the demand for crude and placed on the market an oversupply of finished products, particularly gasoline. The marketing section of the industry has made progress by its adoption of the Code of Ethics as promulgated by the Federal Trade Commission and by the formation of an Export Association. The year 1929 opened not only with a current supply of oil exceeding demand but with an additional daily shut-in and potential supply variously estimated at from 3,000,000 to 5,000,000 bbl. This situation stimulated the industry, through the American Petroleum Institute, to attempt to work out an economically sound solution which would further conservation by bringing supply and demand into closer balance. Production Control After a thorough study of producing conditions, the committee of the American Petroleum Institute had for its recommendation that the production of crude oil in 1929 be held in check to an amount equal to that produced during the year 1928. The Federal Oil Conservation Board heard the appeal of the American Petroleum Institute and referred the matter to the Department of Justice. It was ruled that neither the Federal Oil Conservation Board nor the Department of Justice had the * Land and Oil Production Dept., Henry L. Doherty & Co.

Jan 1, 1930

By M. C. J. van der Merwe

"Carboxymethyl cellulose is an organic binder used in the iron ore pelletizing industry. The basic principles of how carboxymethyl cellulose (CMC) solutions behave during the pelletizing process and how these principles affect the drop and compression strengths of the pellets are poorly understood. The aim of the investigation was therefore to gain knowledge on the behaviour of CMC during the pelletizing of haematite concentrate.Haematite pellets with different additions of CMC (0.1–0.4 wt%), were subjected to drop tests, compression tests, and free moisture content analysis. The relationship between the drop strength, compression strength, free moisture content, elapsed time, and CMC concentration was analysed.The drop strength had a strong correlation with the free moisture content of the haematite pellets, with a correlation coefficient of 0.94. The compression strength of the CMC-bonded haematite pellets increased as the free moisture content decreased, reaching a maximum upon depletion of the free moisture content. Haematite pellets with CMC concentrations of 0.1 and 0.2 wt% developed most of their strength within the first day after pelletizing, whereas pellets with concentrations of 0.3 and 0.4 wt% developed most of their strength between one and two days after pelletizing. The time within which CMC-bonded haematite pellets develop most of their strength is therefore dependent on the CMC concentration. IntroductionFines are produced during the beneficiation of iron ore. These fines are separated from the lump ore and can be upgraded to produce a concentrate, which is used as a raw material for the production of pellets. Pellets in turn form a key burden material for direct reduction processes as well as the blast furnace (Zhu et al., 2015).Inorganic binders such as bentonite have been used predominantly in the iron ore pelletizing process to obtain pellets with suitable properties (Eisele and Kawatra, 2003). These binders, however, have the disadvantage of introducing impurities into the pellets. This has resulted in organic binders being pursued as suitable replacements for inorganic binders, of which carboxymethyl cellulose (CMC) shows good potential. Although CMC has been used as an organic binder in iron ore pelletizing, the fundamental principles of how it behaves during pelletizing and how these impact on pellet properties are poorly understood."

Jan 1, 2017

By J. R. Coulter, F. O. Case, H. G. Satterthwaite, B. Harden

During the two years that the Henderson plant has been in operation, a number of technical improvements have been made by the staff of Basic Magnesium, Inc., the effects of which were realized subsequent to the writing of the paper by Major C. J. P. Ball (p. 28j, this volume). Pellet Mix The process as originally installed required the use of peat moss in the mixture going to the chlorinators. This had to be imported from Canada at a considerable cost, and, besides being expensive, constituted a serious fire hazard in the dry climate of Nevada. Experimentation looking toward its elimination had been going on for some time and was actively pushed as soon as operations commenced. It was found that a pellet mix containing no peat, which would chlorinate at a satisfactory rate, could be cast as a fluid slurry, which would set up into a hard mass having the desired porosity. For carrying out this operation, equipment similar to that used in the manufacture of phosphate fertilizer at Anaconda, Mont., was installed and proved eminently successful. The dry materials, with peat moss and raw concentrates entirely eliminated, are mixed with magnesium chloride solution in two Pratt phosphate mixers and the resultant slurry is poured onto two 48-in. slowly moving rubber conveyor belts. By the time the slurry has reached the head pulley, the material has set su4iciently to be broken and sized as desired. The discharge from the casting belts is fed to the four rotary kilns in the preparation plant, where it is dried and coked to the proper degree for subsequent chlorination. With the peatless feed the capacity of the kilns was found to be about double what it had been before, so that the four rotaries suffice for a 10-unit operation, thus making it unnecessary to operate the extruders and tunnel kilns. In addition to saving the cost of the peat, the new system can be operated with about 85 per cent less labor than was formerly required in the preparation plant. The new pellet production system has also made it feasible to install centralized crushing equipment with suitable conveyors and a loading station. Containers of 8000 lb. capacity were substituted for small cubicles of 1000 lb. capacity which formerly were used for charging the chlorinators, and trailer trucks were substituted for the small trains originally provided for transportation from the preparation plant to the chlorinators. These changes resulted in a considerable saving in handling and transportation charges. Handling Molten Metal The molten magnesium originally was ladled from the electrolytic cells into small gas-fired brick-lined cars standing between the cell rows. From these cars the metal nes ium. into ''cheeses'' weighing from 150 to 300 lb. After solidification the

Jan 1, 1944

Smoky Valley Mining Company, Round Mountain, Nevada, was the pioneer operation designed for large scale heap leaching of crushed gold ores. It is located in the Big Smoky Valley which stretches 160 km (100 miles) through central Nevada west of the Toiyabe Mountain Range. Gold was first-discovered at Round Mountain, 88 km (55 miles) north of Tonopah, in 1905; and mining in the area included placer operations, which ran from 1946 to about 1960. Smoky Valley Mining Company is a partnership of Felmont Oil Co., Case-Pomeroy & Co., and Copper Range Co., with the latter being wholly owned by Louisiana Land and Exploration Co. In 1969, an option on the Round Mountain property was acquired by Copper Range, and during 1974 a decision was reached to proceed with mine development and plant construction. Ore reserves were reported at 10,537,000 mt (1 1,617,000 st) of 2.09 g per mt (0. 061 oz per ton) gold using a cut- off grade of 0.69 g (0.02 oz). Silver content was approximately 2.4 g per mt (0.07 oz per ton) and the waste to ore ratio was about 1: 1. By the end of 1976 heap leaching was in operation. The ore is a rhyolite tuff, sometimes described as a gold porphyry with highly abrasive qualities but which does not break down into slimes upon contact .with cyanide solutions. Gold is unevenly distributed through the ore but as a whole it is in a very finely divided state. Climatic conditions are extreme in central Nevada. Summers are hot and dry while winters are windy and cold with subfreezing temperatures. Elevation of the property is about 1,920 m (6,300 ft). Precipitation averages 203 mm (8 in.) per year. Until February of 1980, leaching was continued until the temperature reached minus 2ºC (28º F), and about 10 months leaching was the average. Water for the operation is drawn from the Toiyabe Mountains through a 13. 7 km (8. 5 mile) pipeline, originally installed in 1915, or from wells in the valley bottom. The plant requires make-up water at the rate of about 1,500 liters per min (400 gpm). On a schedule of three shifts, seven days per week, the daily output at Round Mountain amounts ,to 12, 700 mt (14, 000 st) consisting of 6,350 mt (7,000 st) each of ore and waste. Ore is hauled with a fleet of 45 mt (50 st) trucks and dumped into the 1,0.70 by 1,650 mm (42 by 65 in. ) gyratory primary crusher located near the pit. The primary

Jan 1, 1981

By Suleyman Tekeli, Serdar Salman, Bulent Aktas

"The effect of La2O3 content up to 15 wt% on phase stability, sintering and microstructure of cubic zirconia (8YSZ) was investigated. XRD results showed that the specimens containing up to 15 wt% La2O3 were composed of only cubic structure. Also, the specimens doped up to 5 wt% La2O3 revealed no La2O3 peaks, indicating that La2O3 was completely solubilized in the cubic structure. However, when> 5 wt% La2O3 was added, the peak of La2Zr2O7 compound emerged, showing that the overdoped La2O3 was not solubilized in the 8YSZ matrix. The lattice parameter of the 8YSZ slightly decreased with the increasing La2O3 content up to 1 wt% but further increase in the La203 amount resulted in an increased lattice parameter. The comparison of grain size of the 8YSZ specimens with various La2O3 content showed that grain size slightly increased with the increasing La2O3 content up to 1 wt% but further increase in the La2O3 amount resulted in a decreased grain size.IntroductionAt atmospheric pressures, three polymorphic forms of Zr02 are stable at different temperatures i.e. monoclinic, tetragonal and cubic. A high-pressure orthorhombic form of Zr02 has also been reported[l]. The successful production of pure Zr02 bodies is not possible all the time due to the large volume expansion associated with the martensitic tetragonal-monoclinic transformation. This fact restricts the applications of zirconia, in spite of its excellent mechanical and thermal properties. However, the stabilization of the high temperature polymorphs at room temperature as stable phases is made possible by addition of suitable dopants. Fully stabilized cubic Zr02 and partially stabilized tetragonal Zr02 show interesting properties and are widely used as ionic conductors, coatings and gas sensors in solid oxide fuel cells and structural applications[2]. Most frequently used dopants include Y203, CaO, MgO and Ce02, although other oxides, such as those of rare earth elements, can also act as stabilizers of the high temperature structures. The incorporation of aliovalent cations to the lattice, forming substitutional solid solutions, allows to control the concentration of anionic vacancies in the structure. This aspect is particularly important in designing ionic conductors[3], and is also determinant in the stabilization process[ 4]. The process of stabilization with larger ionic radii dopants is rationalized by the crystal chemistry model[ 5], that describes the dopant cations as typical stabilizer when they have larger ionic size, lower charged state and higher ionicity than Zr4+ The ionic radius of Zr4+ is 0.84 Å and that for La3+ is 1.016 Å [6]."

Jan 1, 2012

By H. E. Wilde

"Zinc has been used for many years as a galvanic coating for the protection of steel. Electrochemical measurements show that zinc actually overprotects steel. The corrosion rate of DQSK (drawing quality semi-killed) steel in air saturated salt water was determined as a Junction of applied cathodic potential. The resulting data indicate that at a critical cathodic over potential of - O. 725 Vsce an acceptably low corrosion rate of less than 1 mpy occurs. Using the developed criterion, alloys of Zn/X and AL/X were produced and evaluated in galvanic contact with steel in a standard laboratory test. The results indicate that Zn /Mn, Zn /Co, AI/Mg/Si and AI/Mg/Ge alloys offer excellent galvanic protection along with (a) no hydrogen evolution, and (b) improved dissolution life over Zn coatings.IntroductionZinc coated (galvanized) steel has been successfully used in applications where bare (or painted non-galvanized) steel would suffer corrosive attack. In general, galvanic coupling to zinc, as either an anode or a coating, is an effective means for combatting steel corrosion. Because of this, the use of galvanized steel has increased markedly, stimulated primarily by automobile manufacurers seeking to extend the corrosion warranties on automobiles(1).Although effective, zinc coatings are not without a number of drawbacks which warrant efforts to improve them. For example, because of the widely differing electrode potentials between zinc and steel ( - 1.05 Vsce and - 0.60 Vscc, respectively, in air saturated NaCl solutions), the zinc corrodes at a rapid rate to protect the steel. This is reflected in the limited lifetimes of galvanized unpainted siding. The basic electrochemistry controlling the situation is shown in Figure 1, for a system controlled by oxygen reduction. The zinc corrodes sacrificially to protect the steel, while cathodically polarizing the steel to a potential near that of zinc's open circuit anode potential."

Jan 1, 1990

By Shantanu Patel, C. Derek Martin

"The objective of this work is to develop a practical numerical approach for applying the confining pressure to discrete element cylindrical triaxial tests. A layer of membrane particles with very low stiffness and extremely high contact bond strength was created around the lateral boundary of the cylindrical numerical specimen. To prevent the membrane particles from penetrating into the rock specimen on application of confining forces and to provide a smooth boundary surface, the space between the membrane and rock particles was filled using small-diameter packing particles. The results of this method were compared with those of rigid boundary method with confining pressure of 20MPa. The results obtained show that new approach gives both peak strength and post peak response that are in closer agreement with laboratory findings. BACKGROUNDThe discrete element method (DEM) has become the cornerstone for simulating both intact material and discrete fractures for low porosity strong rocks (ISRM Classes R3 to R6). Despite the advances in its application, simulating realistic behaviour of intact rock using the DEM remains a challenge. The bonded particle model was introduced as a potential solution for simulating the complex mineral grains in strong rock and other granular materials (Potyondy and Cundall, 2004; Utili and Nova, 2008; Salot et al., 2009). While some issues were resolved, a remaining challenge is the lack of the bonded particle model to simulate the brittle response commonly observed in strong rocks during the triaxial compressive test. Such behaviour is shown in Fig. 1 for Lac du Bonnet Granite at a confining pressure of 20MPa."

Jan 1, 2015

By KeerthiRaaj Subrmanian, Muthukkumaran Kasinathan

"A railway embankment is under construction between Nagapattinam to Thiruthuraipoondi covering 36.5 km. The sub-soil strata comprises of soft clay extending up to 10 m below existing ground level, which is subjected to stability and settlement problems. A trial stretch covering about 5 kilometer was improved using Prefabricated Vertical Drains (PVD) with surcharge was recommended to accelerate the consolidation settlement. The geotechnical characteristics of the subsoil are examined through laboratory tests on representative soil samples. Recent improvement in the finite element analysis has facilitated modeling of PVD in finite element software for computing the settlement magnitude and time rate of consolidation. In this study the theoretically predicted settlement magnitude and time rate of consolidation from Terzaghi.s vertical consolidation, Barron's radial consolidation are compared with the analyzed FEM results for both the cases with and without PVD improved embankment. The comparative analysis between FEM and predicted data hold good for stresses and the associated deformations. The excess pore water pressure was significantly lower and their dissipation was faster in case of embankment with vertical drains. Thus PLAXIS 2D tool shows fairly convincing results in comparison to the theoretical solutions.1. INTRODUCTIONFrom the earlier times civilization has been developed in a fashion either at the banks of river or near to the shore region, because of the easier availability of food and water. This over centuries made them as huge cities, consequently population rise made the increased necessity of highway, railways, port and even more ground for construction. As a stake researchers are pushed to make a low bearing ground into a massive carrier of skyscrapers, embankment, bridges etc. These low bearing ground suffers from total and differential settlement, slope instability. Hence, numerous ground improvement techniques were followed to eradicate these concerns which include preloading, piling, stone column, vertical drains and geosynthetic reinforcement. Among them Prefabricated vertical drain (PVD) are often used to accelerate consolidation of soft subsoil and has been the main soil improvement method used in improving the soft marine clay deposit (Chu et al.(2004); Chai (2001) and Arulrajah et al.(2003)). Literature review of embankment over soft clay deposit reveals that combination of PVD with preloading is widely considered as an economical and less time consuming ground improvement technique."

Jan 1, 2015

By Franz R. Dykstra, R. F. Tatnall

A ferroalloy is defined as: "An alloy of iron with some element other than carbon used as a vehicle for introducing such an element into the manufacture of steel. The element may alloy with the steel by solution or, as the carbide, -neutralize the harmful impurities, by combining with them and separating from the steel as flux or slag before solidification."a The most commonly used ferroalloys are: ferromanganese, ferrochrome, ferrosilicon, ferrovanadium, ferromolybdenum, ferronickel, ferrotungsten, ferrocolumbium, and ferrophosphorus. Concern here is with the sources and markets of the major metallic alloying elements. The discussion is further restricted to those - ferroalloy ores, the principal use of which is in the production of steel. Phosphorus, silicon, and tungsten, for example, are ferroalloys of some economic significance, but other uses dwarf their alloying applications. Thus, this discussion will deal with the ores of managanese, chromium, nickel, molybdenum, vanadium, and columbium. As shown in Table 14.1B.1 ferroalloys serve to- facilitate processing and impart to the finished steel such characteristics as tensile strength, ductility, low-temperature impact, hardenability, high-temperature strength, corrosion resistance, toughness, and abrasion resistance. In the steel-making process, ferroalloys may be added in the charge, in the molten bath near the end of the finishing period, in the ladle, or in the molds. Timing of the addition depends on the effect of the addition on the temperature of the molten metal, the formation and elimination of reaction products, and the protection of subsequent additions from oxidation. MANGANESE General Approximately 95% of the manganese ore sold is consumed by the steel industry, either as ferromanganese or as manganese metal. Manganese is the universal alloy, without which good steel cannot be made. It serves as a scavenger, removing phosphorus, sulfur and, to a degree, oxygen from the melt. As an alloying material it makes steel hard, tough, and resistant to wear. Approximately 6 kg of manganese is required for every ton of common steel produced by United States steelmaking practice. The remaining 5 % of the manganese ore consumed consists of special or so-called "chemical" ores, including high-grade pyrolusite ores, electrochemically reactive "battery ores," and a number of special varieties, as well as those otherwise regarded as "metallurgical ores."

Jan 1, 1976

By W. Díaz, R. A. Parra, L. E. Arias, C. A. Toro, M. Marin, E. Balladares, V. Parra, G. Reyes, S. N. Torres, D. Sbarbaro

This work presents visible-near infrared (VIS-NIR) spectroscopy measurements, and signal analytical techniques to characterize minerals and relevant pyrometallurgical process variables for the copper extractive industry. Data signal processing techniques such as baseline correction and numerical analysis are used to estimate the continuous and discontinuous spectral components. Such spectral components are used to estimate the process temperature, and patterns such as the integrated radiation. Also, metal combustion emissivity calculation are depicted. Our findings suggest that VIS-NIR spectroscopy may be a suitable technique to assess the process condition state, appearing as an interesting sensing alternative. INTRODUCTION Although the flash smelting process is one key stage in the copper extractive industry, representing about 40% of copper matte production worldwide (Cantallopts, 2017), few attention is dedicated to develop sensing solutions to assess process variables, such as mineralogical composition and temperature, in the feeding and bleeding stages, compared to the steel industry (Strakowski, et al., 2014). In this process and other industries, e.g. the thermoelectric power generation one, combustion and particularly the generated flame are the production chain’s heart. Since the flame is a highly radiative emitting process where chemical and physical transformations take place, many works had been dedicated to characterize the combustion state by sensing its radiation using optical and photonic technologies (Ballester & García-Armingol, 2010). In this context, this work aims to contribute with visible-near infrared (VIS-NIR) spectroscopy and pyrometry techniques to retrieve relevant information from a laboratory scale flash smelting process. On the other hand, since photonic instrumentation allow us to perform contactless measurements of emitted, absorbed, transmitted or scattered radiation, it appears as a suitable technique for sensing process properties in harsh environments, e.g. high temperature processes. One of these techniques is the Visible- Near Infrared (VIS-NIR) spectroscopy, which provides information about the spectral radiation intensity distribution, in this work, the emitted flame’s radiation. It is well known in combustion research that the spectral emission from a flame is composed by a black body continuous radiation background, molecular emissions, elemental emissions and additive noise features (Arias et al., 2011). To make sense of such information signal processing techniques are needed, here we propose to analyse the continuous and discontinuous spectral components separately.

Jan 1, 2019

By J. Nagy, D. W. Mitchell, E. M. Murphy

In 1957 research was initiated in the U.S. Bureau of Mines experimental coal mine near Pittsburgh, Pa., to study factors affecting foam generation and transport, to evaluate the effectiveness of high-expansion foam for controlling mine fires, and to develop techniques for applying the method under U.S. mining conditions. These investigations showed that high-expansion foam containing at least 0.2 oz of water per cu ft of foam is effective in controlling experimental underground fires burning coal, wood, and oil. Sometimes the fire was completely extinguished, but more often, it was brought under sufficient control to permit either a direct attack on the fire with a stream of water or loading of the hot material into cars. A progress report' prepared in July 1958 summarized the initial achievements of the USBM experiments. Since then other phases of the foam-plug method for attacking fires have been studied in the laboratory and in the mine. Previous studies by British engineers' of the foam-plug method for fighting mine fires indicated that high-expansion foam was effective in controlling experimental timber fires in an underground passageway. Their subsequent workx-1 pertained to the practical aspects of fighting large fires within a mining area with a foam-plug. CONTROLLING EXPERIMENTAL FIRES In the USBM tests foam was formed by spraying a dilute solution of a foaming agent on a metal or cotton net of 1/8 to 1/4-in. mesh. Air passing through the continuously wetted net forms bubbles of 1/2 to 11/2-in. diam and produces a honeycomb of foam that fills the passageway. Under the ventilating-air pressure, this light-weight plug moves forward through the passageways, around sharp corners, and over obstacles. as illustrated in Fig. 1. High-expansion foam was transported to a wood fire, an oil fire, and 13 coal fires. Figs. 3 and 4 show a typical coal fire before and after attack with foam. In 12 of the 15 experiments the fire was brought under control when the water content of foam was 0.2 oz or more per cu ft. A fire was considered controlled when the flames were quenched and observers could cross the area without wearing breathing apparatus or protective clothing. In the other three experiments, conducted when the water content was less than 0.2 oz per cu ft of foam, the flames were retarded but the fire was not controlled. Coal fires have been attacked successfully by foam introduced at points varying from 155 to 1010 ft from the fire. The time of burning in coal beds 10 in. thick ranged from 11/2 to 5 hrs or more. Most of the experimental fire beds were 15 ft in length. However, in one experiment a floor fire 25 ft long and 5 ft wide was constructed $5 upwind from another fire 15 ft in length; in another instance, the fire was 100 ft long and 5 ft wide. Foam was applied to the fires for periods ranging from 7 to 36 min. The time required for foam application depends on the extent of the fire, time of burning, water content of foam, foam velocity, and degree of fire control desired. In addition to the coal fires, foam was transported to a fire covering 45 sq ft, produced by 15 gal of oil burning in metal trays on the floor. The foam extinguished the oil fire in about 1 min. In one other test, the burning of 1100 lb of dry sawmill slabs stacked in open cribs 4 ft high and 16 ft long was brought under control by foam in 2 min. Composition of Gases in Return Air: In several of the experiments samples of the return air from fire zones were collected; composition of the atmosphere before, during, and after foam application was then determined. Because of condensation in the relatively cool sampling tube, the amount of water vapor was not determined. Analyses showed that concentration of carbon dioxide and combustible gases increased as the foam began passing over the fire. This resulted from the decrease in the volume of air when foam generation started and from the formation of gases when water reached the fire.* The quantity of gases generated would not be greater than that from an equivalent amount of water applied directly to the fire. The highest total concentration of combustibles (CO, CH1, and H2 mixture) obtained during the experiment was about 2 pct; this occurred 6 min after foam reached the fire. This atmosphere was nonex-plosive, but calculations show that if the air flow were reduced to about 5 fpm and if the rate of gas liberation from the fire remained constant, the mixture would be explosive. The use of foam on a fire in all probability would affect the normal ventilation of a mine. If the mine is gassy, this factor must be carefully considered before the foam is applied. APPLICATION OF THE FOAM-PLUG TECHNIQUE IN MINES Equipment and procedures for applying the foam-plug methods must be adapted to the prevailing conditions at a particular mine. Some factors to be considered in developing equipment are: size or extent of the mine, dimensions and number of entries, ventilation system, mining methods, haulage facilities, availability of water, amount of methane liberated, and existing fire-control apparatus. • In most experiments the initial air velocity of 200 fpm decreased to 50 to 100 fpm as the foam plug increased In length.

Jan 1, 1961

By C. A. Stetefeldt

Steam-dRied sulphides, obtained in the lixiviation-process, are now almost exclusively sold to smelters, the old methods of melting (after roasting) in crucibles, or cupelling with lead at the mill, having

Jan 1, 1892