Search Documents

By D. Raicevic

The presence of residual uranium and other radionuclides in the uranium mill tailings are posing a continuous health concern to the surrounding environment. The slow generation of sulphuric acid from residual sulphide minerals is the cause of persistant dissolution and discharge of many metallic components of the tailings. The most effective long term solution to these problems would seem to be to produce chemically stable tailings. This paper describes two possible answers to the objective: (1) Removal of radionuclides and pyrite from tailings by mineral dressing techniques; some 60 - 68% of the residual uranium, 70 - 75% of the radium, 60 - 65% of the thorium and 95 - 98% of the pyrite have been rejected from the Elliot Lake tailings. The decontaminated tailings contained 0.003% uranium, 50 - 60 pCi/g radium226, 0.01% thorium and less than 0.1% sulphur as pyrite. (2) Preconcentration of radionuclides and pyrite by beneficiation from Elliot Lake ores prior to leaching; applying this approach about 97% of the uranium, 95% of the radium, 92% of the thorium and 98.5% of the sulphides were concentrated in a radionuclide and pyrite concentrates comprising 25% and 8% of the ore, respectively. The preconcentration tailings (waste) produced contained 0.004% uranium, 20 - 25 pCi/g radium226, 0.005% thorium and less than 0.1% sulphur as pyrite. Economic and environmental advantages of both approaches and the leaching of the concentrates are also discussed.

Jan 1, 1980

By C. E. Lesher

THE Disco* process for the production of low temperature coke and its immediate predecessor, the Wisner or Carbocite process have been described in the voluminous literature of low temperature carbonization.1-4 This paper will describe the development of the process from the first attempt at commercial operation by the American Gas and Electric Co. at Philo, Ohio,' in the 1920's to the successful operation in 1949 by the Disco Co., a division of the Pittsburgh Consolidation Coal Co., of the 1000-ton per day Disco plant near Pittsburgh, see Figs. 1-2. In the 1924 coal industry depression following the hectic post World War I expansion, the northern Appalachian, unionized bituminous coal fields were affected first and foremost, and Western Pennsylvania as hard as any. Competitive market pressure was heaviest on the lower grades of steam coals, notably those from the Panhandle district where ash and sulphur are inherently higher than in the same Pittsburgh coal bed to the east along the rivers. The firm structure of Panhandle coal while favoring the prepared sizes, depressed the usefulness and value of the finer sizes. Panhandle slack and nut slack were marketed with difficulty at consistent, and at times considerable, loss. Many solutions were suggested, and the Pittsburgh Coal Co. investigated all. Lower delivered prices through lower mine costs and more advantageous freight rates were obvious goals, but equally obvious were the difficulties of self attainment of either in any substantial measure. Selling Btu's in pipes was abandoned as an idea after a thorough study of the economics of distribution of what was then, and is even now, the only developed continuous process of complete gasification of bituminous coal-producer gas. Although the coal company purchased huge blocks of electric power, it sold not a car of coal to the central power stations. Public utilities controlled the markets for electric current, and it was found that no matter at how low a cost current might be put on the bus bars by the coal company, distribution to its widely scattered coal mines made such an enterprise practically impossible. Consolidation of underground operations and a huge modernization program of mining operations in the 1920's were but preparation for the introduction of mechanical cleaning of the coal for market, particularly the smaller sizes of steam, gas, and by-

Jan 1, 1952

By W. G. Pariseau

This paper is concerned with the problem of calculating ground movement that occurs as a consequence of mining. Solution to this problem is straight forward in principle but rather complex in practice. The complexities of the problem arise from the ever present constraints of technology and economics. However, the identity of these constraints is often obscured by a faulty understanding of the fundamentals of the problem and a lack of appreciation of current computational capabilities and costs. As a consequence much time and effort are sometimes wasted on gathering information that is of little direct value to ground control programs while important input data are neglected. This paper therefore reviews the essentials of the process of formulating the ground movement problem. Emphasis is upon application to longwall mining, although much of the discussion applies to other mining methods as well. In many instances, the hardrock term stope could be substituted for longwall panel because the fundamentals of the problem are independent of the excavation dimensions and numerical values of rock properties. The latter affect the outcome of a calculation, of course, but not the underlying formulation. Only the major features of the problem are discussed in this brief review. The objective of the discussion is the generation of a reliable basis for developing a technically sound ground control strategy. Any rational ground control strategy must be consistent with basic physical laws. For example, under static conditions, equations of equilibrium must be satisfied. Operational, that is, tactical, details may vary widely with local conditions, but the basic approach must be based on physical laws. The alternative empirical route is intrinsically unreliable and unnecessary as well. Empirical descriptions of ground motion caused by mining including recent statistical curve fits to specialized data sets (for example, surface subsidence data) as well as antiquated "theories" of ground pressure and so forth, however dignified with mathematical formulas, are hardly worthy of the label "theory". Extrapolation of statistical data is always accompanied by rapidly diverging confidence limits, while empirical equations simply lack predictive capability under circumstances even slightly different from those of the original development. For example, applications of surface subsidence curves generated empirically in the United Kingdom to coal mines in the United States generally result in considerably greater subsidence and wider subsidence troughs than actually observed. Locally, empirical criteria for specific ground control actions may be made practical through trial and error, but such tactics are no basis for the development of a general ground control strategy. In this regard, it is worthwhile to recall the traditional scientific distinctions between speculation, hypothesis and law, between the empirical and the proven.

Jan 1, 1982

By J. P. Heller, H. B. Bradley, A. S. Odeh

A potentiometric model technique is presented for determining the areal sweep efficiency of a five-spot well pattern, at and beyond breakthrough. A sharp interface between displaced and displacing fluids is assumed. Although the prototype svstem is referred to as a waterflood operation, obvious changes in the notation and computations will adapt the results to other displacement processes. The results of the study include the following. 1. Areal sweep efficiencies for a five-spot well pattern, at and beyond breakthrough, for mobility ratios (displacing to displaced fluid) of 4:1, 2:1, 1:1 and 1:4. 2. Extension of potentiometric analysis to the investigation of the areal sweep efficiency beyond breakthrough in a five-spot pattern by the application of conformal mapping and conductive-solid models. 3. The use of layers of conductive fabric in representing mobility ratio changes in potentiometric models. 4. The development of a probe mechanism for probing conductive solids. The results obtained by conductive-cloth models agree with earlier areal sweep efficiencies at breakthrough obtained by Aronofsky and Ramey 1 on the potentiometric analyzer using electrolytic-tank models. Results beyond breakthrough differ from those obtained by the X-Ray Shadowgraph technique. Data from this study show that, for mobility ratios greater than one, water cut rises rapidly as fluid is produced after breakthrough. However, for mobility ratios smaller than one, a large increase in area swept resulted with only a small increase in water cut. INTRODUCTION In calculating reservoir performance of waterflood-ing operations and other fluid-injection programs, it is necesssary to estimate the areal sweep efficiency * before and after injected-fluid breakthrough into production wells. Influence of mobility ratio on oil-production history, before and after breakthrough for a five-spot well pattern, has been studied by X-Ray Shadowgraph techniques 2-5 and by gelatin models.6 In none of these investigations was the transition zone controlled experimentally. Steady-state anaiog techniques assume that a vertical and discrete interface exists between the displacing and displaced phase. Thus, when using a potentiometric analysis, it is assumed that no transition zone exists. To determine the areal sweep efficiency beyond breakthrough for a five-spot well pattern using the potentiometric analyzer, four principal problems had to be resolved. These were the following. 1. The laborious method of representing changes in mobility ratio in electrolytic tanks by means of contoured wooden blocks. 2. Vapcrization of the electrolyte solution during the study causing concentration changes and, thereby, variable conductivity. 3. The scale-limitation problem 7 that is accentuated by abrupt eiectrolyte depth changes. 4. A wellbore geometry problem. EXPERIhlENTAL EQUIPMENT AND PROCEDURES CONDUCTIVE-SOLID MODEL The theory, equipment and procedural techniques of the electrolytic-tank potentiometric model have been treaced excellently by Lee8 and by Muskat.9 By the use of a conductive solid to represent the fluid conductivity of the porous media, the need for contouring wooden blocks to represent mobility ratio was eliminated. It was found that a carbon-black coated fabric, Uskon D-16,** could be employed as a fairly uniform conductive media. This material, when stacked in appropriate layers and pressed together, can be used to represent changes in mo-

By Jan Law

Problems of oil recovery are attacked from the approaches dictated by the two strikingly dissimilar complexes that comprise an oil reservoir—the fluid complex and the interstitial complex. Knowledge of the fluid complex, due to labors in the fields of fluid mechanics and physical chemistry, has far outdistanced knowledge of the interstitial characteristics of the sand complex. This paper is concerned with the latter and applies the technique of statistics to petrographic facts—namely, porosity and permeability—dealing with what might be called petrometry. Statisticians have long worked within the problem of reconstruction of a universe oi variables by means of samples that comprise a small percentage of the universe from which the samples were drawn. Core-analysis data comply with the requisite of random sampling as stipulated by theoretical statistics. A basic concept of statistics employs t.he following substitution: 1. The results of sampling are arranged as a frequency distribution. 2. The observed frequency distribution is compared with a mathematically precise distribution. 3. If a sufficiently good agreement is found between the two, the precise distribution is substituted in all subsequent operations involving characteristics of the sampled material. This mathematically precise distribution is also known as the normal curve, curve of error, the probability, the Gaussian, and the bell-shaped curve and is describable with but two figures. Further, these two figures, the arithmetic average and the standard deviation, are subject to mathematical manipulation. This paper demonstrates that, in some cases in the Dominguez field of Southern California, if sufficient core-analysis samples are taken over not too great a thickness of sediments, the resultant permeability and porosity assemblages give satisfactory agreement with ilormal curves. It is shown that the indications are strong that oil wells wherein a satisfactory agreement is found are predictable as to productivity. Since the predictions are made by employing the laws of chance that are operative within sedimentation, it follows that the mechanism by which the predictions were made is a basic concept of reservoir mechanics. Therefore, tentative examples are given of the application of normal curves to the solution of problems of primary and secondary recovery. Nature of Permeability Frequency Distributions Core-analysis data are made available as a tabulated depth vs. permeability profile. The nature of the distribution of permeability values within a given strati-graphic interval may be approximated from an array constructed with samples plotted in the order of their appearance with depth (accession number) against their permeability value in millidarcys. A wide variation in the nature of the distribution of K (permeability) values for

Jan 1, 1944

By Jan Law

Problems of oil recovery are attacked from the approaches dictated by the two strikingly dissimilar complexes that comprise an oil reservoir—the fluid complex and the interstitial complex. Knowledge of the fluid complex, due to labors in the fields of fluid mechanics and physical chemistry, has far outdistanced knowledge of the interstitial characteristics of the sand complex. This paper is concerned with the latter and applies the technique of statistics to petrographic facts—namely, porosity and permeability—dealing with what might be called petrometry. Statisticians have long worked within the problem of reconstruction of a universe oi variables by means of samples that comprise a small percentage of the universe from which the samples were drawn. Core-analysis data comply with the requisite of random sampling as stipulated by theoretical statistics. A basic concept of statistics employs t.he following substitution: 1. The results of sampling are arranged as a frequency distribution. 2. The observed frequency distribution is compared with a mathematically precise distribution. 3. If a sufficiently good agreement is found between the two, the precise distribution is substituted in all subsequent operations involving characteristics of the sampled material. This mathematically precise distribution is also known as the normal curve, curve of error, the probability, the Gaussian, and the bell-shaped curve and is describable with but two figures. Further, these two figures, the arithmetic average and the standard deviation, are subject to mathematical manipulation. This paper demonstrates that, in some cases in the Dominguez field of Southern California, if sufficient core-analysis samples are taken over not too great a thickness of sediments, the resultant permeability and porosity assemblages give satisfactory agreement with ilormal curves. It is shown that the indications are strong that oil wells wherein a satisfactory agreement is found are predictable as to productivity. Since the predictions are made by employing the laws of chance that are operative within sedimentation, it follows that the mechanism by which the predictions were made is a basic concept of reservoir mechanics. Therefore, tentative examples are given of the application of normal curves to the solution of problems of primary and secondary recovery. Nature of Permeability Frequency Distributions Core-analysis data are made available as a tabulated depth vs. permeability profile. The nature of the distribution of permeability values within a given strati-graphic interval may be approximated from an array constructed with samples plotted in the order of their appearance with depth (accession number) against their permeability value in millidarcys. A wide variation in the nature of the distribution of K (permeability) values for

Jan 1, 1944

By J. T. McGrath, G. B. Craig

Tensile tests on aluminum single crystals, grown from the melt, revealed that the yield stress of these crystals was raised as the amount of striation substructure was increased. The number of striation-type boundaries was varied by changing the rate of growth of the crystals. The results are interpreted in terns of a blockage of dislocation movement by striation boundaries. IMPERFECTIONS are known to have a large effect on the mechanical properties of metals. Teghtsoonian and Chalmers 1 studied a block or striation-type substructure in tin and found that the formation of the striations depended upon rate of crystal growth and orientation. They found that the angular misorienta-tion between neighboring striations varied between 15 min and 5 deg. Atwater and chalmers2 investigated striations in tin and lead, and found that purity was another factor which influenced their formation. There was a limiting purity above which the striations were straight and regular. There is little information in the literature concerning how substructures in melt-grown crystals affect strength. washburn3 introduced small-angle boundaries into zinc by a shear process and found a subsequent increase in yield stress which he attributed to the presence of these boundaries. Lauriente and pond4 found the critical resolved shear stress in aluminium crystals grown from the melt, to increase with etch pit density. The etch pits were used as an indication of growth imperfections. In Hibbard's5 work on lineage structure in copper crystals grown from the melt, he tested one crystal containing interlineage boundaries, and found a 50 pct increase in the critical resolved shear stress. Fleischer and Chalmers6, in a recent paper, mention briefly that, in the production of aluminium crystals from the melt when the growth rate was raised from 1.2 to 18 cm per hr, the yield stress increased 50 pct. They felt that the increase in yield stress with rate of growth might be attributed to a higher concentration of impurities in the gage length and also might be affected by the increased number of small-angle boundaries (striations). The present investigation was undertaken to determine the effect of the striation substructure on the strength of aluminum single crystals. EXPERIMENTAL PROCEDURE Aluminum single crystals of 99.9992 purity were grown from the melt using a technique described by Chalmers.7 The growth rate was varied from 0.6 to 20 mm per min, thus producing crystals with varying numbers of striation boundaries. To avoid prior deformation, the crystals were chemically cut to the desired length with a saturated solution of cupric chloride. They were then annealed at 580°C for 24 hr and allowed to cool slowly in the furnace. Finally, the specimens were electropolished using an electrolyte of 5 parts ethyl alcohol and 1 part perchloric acid. Each specimen was approximately 5 in. in length and 0.125 sq in. in cross section. The average orientations of the 5 series of crystals studied are shown on the stereographic projection of Fig. 1. The crystals were strained approximately 2 pct in a soft tensile machine. The strain sensitivity was 3.6 x 10-4 cm over a 5-cm gage length.

Jan 1, 1960

ShouSteel Mining Ltd., a subsidiary of ShouSteel (Group) Co., was founded in 1959 and is located in QianAn City in Hebei Province, China. ShouSteel?s pelletizing plant uses iron ore as a raw material combined with limestone, dolostone, or olivine, with bentonite as a binder. After mixing the raw materials and forming them into small, spherical balls, ShouSteel then fires pellets in kilns for hardening. The company sells the finished pellets as raw materials for blast furnaces used to produce industrial metals such as iron. ShouSteel?s handling capacity is approximately 24.5 Mt/a (27 million stpy) of ore. The company?s production capacity is 3.2 Mt/a (3.5 million stpy) of oxide pellets and 560 Mt (650 million st) of sinters. Until recently, ShouSteel Mining had not replaced its electronic scales in its series of ingredient chambers. Because of the wear and tear on these older scales, the weighing system began to encounter regular problems. The company experienced a high failure rate from the integrator, an unstable signal, weak anti-interference ability and low accuracy. ShouSteel also found that spare parts required during repairs were consistently high in cost and that system calibration was becoming increasingly frequent.

Jan 1, 2012

By W. M. Yim

Experimental results are presented which indicate that transverse striations in horizontal zone-leveled Bi-Sb alloy crystals are due to irregular growth rate resulting from thermal fluctuations in the melt (Iring gowth. Thc thermal fluctutations arose from two different sources. The first type was brought about by periodic fluctuations in the furnace temperature. The second type can be attributed to turbulent therrrol conlcclion in the trzelt near the solid-liquid inteyace. Tile arrzplitlcde ond fvequency of the tetiperaticre fluctlrations vesultity from llle lhevnal con1,ecrrell. The striation spacings in Lhe crystals covvelale well with the periodicity 0.f the tempevature flueluatiors. Altliough the strialiors represenl corrlpositiozul inhoiHogeneity oh a rzicroscule, less than f.z cil. be1 S6 in Best's as deterrirzed by electron-pro be chalq'sis, the slriations roerre fbund to ILUL' no rrleusuanble effect on electical vesistirity rwr on weak field macgnetoresistance of. the Bi-Sb a1lu.y in the ternpevutue ),unge 4.Polo 300°K. DURING the course of an investigation on the horizontal growth of semimetals,' it was found that crystals of Bi-Sb alloys contained many closely spaced parallel arrays of striations. These striations occurred perpendicular to the growth direction and parallel to the solid-liquid interface. We shall refer to them as transverse striations, or just striations'', to distinguish them from lineage substructures or longitudinal striations which form parallel to the growth direction and have been known to be associated with cellular structures.' Similar transverse striations have been reported previously to occur in other materials prepared by horizontal growth: metals,4 semiconductors,5 as well as their alls. - Various methods of crystal preparation have apparently little effect on the occurrence of the transverse striations. They form whether the crystals were grown by the vertical Czochralski technique, withe1' or without'3- rotation, or by the horizontal zoning methd.- Thus, the transverse striations are not limited to any one class of materials, nor to any particular method of preparation. It is likely, therefore, that all of the observed transverse striations may have some common cause. Previously, workers agreed that periodic changes in the growth rate bring about the striations. However, no agreement exists as to the origin of the growth-rate fluctuations. Some attributed the discontinuous growth to a purely external cause, such as fluctuations in the furnace temperature, jerky motions in the crystal pulling mechanism, or a nonsymmetrical temperature distribution in the melt (in the case of crystals grown by the Czochralski technique with rtation). Others looked for the cause in some fundamental property of the growth process itself. For instance, a certain degree of supercooling is required to initiate growth from the melt. But, with further growth, the degree of supercooling decreases because of the liberation of the heat of solidification at the solid-liquid interface. Thus, crystal growth would be brought to a halt until sufficient supercooling is resotred and the cycle begins again.3'11 According to this model, periodic fluctuations in the melt temperature should exist at the solid-liquid interface. Since the periodic fluctuations in growth rate would result in changes in the segregation coefficient of solute atoms, crystals containing the transverse striations may, in some cases, show a periodic impurity fluctuation along the length, resulting in a degradation of electrical properties. The resistivity striations in doped germanium'9-10 or lnsbB are well-known examples of this microsegregation. The present work was undertaken to explain the exact origin of the transverse striations, and to assess the extent of their effect on chemical homogeneity as well as on electrical properties of Bi-Sb alloy crystals. Results from our previous study of the crystal growth of Bi-Sb alloys1 indicated that the transverse striations may arise from the temperature fluctuations in the melt during growth. This paper will show that the melt temperature fluctuations are indeed responsible for the occurrence of the transverse striations. I) EXPERIMENTAL Although the transverse striations have been observed in all slow-grown Bi-Sb alloys across the entire compositional range, we selected a composition, Big3Sbs, for the present study in view of the extensive data available on the crystal growth of this alloy from a previous study.' High-purity bismuth and antimony, both a 6-nine grade by the manufacturer's emission spectrographic analysis, were used throughout. Independent mass-spectrographic analysis showed, however, that the starting materials were more nearly a 5-nine grade. each containing metallic impurities of approximately 10 ppm atomic. In zone-leveled Big5Sb5 alloys, the total metallic-impurity content was slightly lower, about 7 ppm atomic, indicating that some degree of purification was achieved during the growth. None of the electrically active impurities, such as tin and lead (acceptors) and tellurium and selenium (donors), were present in significant quantity in undoped Bi95Sb5. Typical analysis of the undoped Bi95Sb5 alloy is shown in Table I. Nonmetallic impurities, such as carbon and oxygen, were detected, sometimes as much as 100 ppm, in both the starting materials and the zone-leveled alloys: but the data were only qualitative. Temperature fluctuations in the melt were monitored over 1 or more days by means of a 5-mil chromel-

Jan 1, 1967

By A. S. Michaels, R. S. Timmins

A study of the effect upon oil recovery from an un-consolidated porous medium of chromatographic transport of selected reverse-wetting additives during water displacement is described. Flow tests were performed on hydrocarbon oil-saturated sand columns (containing connate water) into which small volumes of short-chain aliphatic amine solutions were introduced during water flooding. Concurrently, meusurements of oil-silica contact angles, oil-water interfacial tensions and oil-water distribution coefficients were measured us a function of additive concentration. Certain treatments were found to cause a slight reduction in oil recovery, while others produced a significant increase (up to 50 per cent of the normtzl irreducible rninimum oil saturation). Recovery eficiency was correlated most satisfactorily with the maximum degree of reverse wetting produced during additive transport; conditions which resulted in only mild oil wettability of the sand reduced recovery, while those favoring strong oil wetting increased recovery. A mechanism of reverse-wetting additive action during chromatographic transport is developed which ascribes the results to transient changes in oil-solid contact angle during flow, with consequent release of oil trapped by capillary forces. Implications of these observations with regard to improved waterflood efficiencies are discussed. INTRODUCTION The need for finding improved methods of oil production is amply illustrated by the large volume of oil considered economically unrecoverable by existing production practice. Water flooding has long been an excellent method of secondary recovery. However, even in those areas of a formation which are well swept by a water flood, 20 per cent or more of the oil remains trapped within the formation and is not recovered. This trapping of oil within the pores of the rock structure results primarily from interfacial forces. If these interfacial forces were altered, it is possible that the trapped oil could be released and recovered. The addition of surface-active agents to a water flood to alter the interfacial properties of the oil-water-solid system has received considerable attention as a method of increasing oil recovery. Studies of surfactant treatment have yielded varied and, in some cases, apparently conflicting results. Increased oil recovery using surface-active agents has been reported by a number of investigators. Others have found that use of surfactants in a water flood either has no effect upon oil recovery or decreases it. Since surface-active agents tend to alter the formation wettability and oil-water interfacial tension simultaneously, several investigators have tried to determine the role these two factors play in oil recovery. Data have been presented which indicate that the most desirable condition for the solid surface is strongly water-wet. Other results indicate that, although breakthrough recovery may be less, the greatest ultimate recovery is obtained when neutral wettability prevails.", " The desirability of low interfacial tension seems to depend upon the wettability of the formation. Reports of higher recoveries, when the interfacial tension is high in a water-wet system and low in an oil-wet system, are at odds with reports of increased recovery in water-wet systems when surfactants which decrease the interfacial tension are added to the water flood. A review of previous work studying the effects of using surface-active agents in a water flood shows that these agents produce widely different effects and that opinions as to the role of the various interfacial properties are diverse. The consensus, however, is that the interfacial properties are quite important in the displacement of oil from a porous medium by water. Even in those investigations where appreciable increases in oil recovery resulted from treatment with a surface-active agent, economic considerations generally made practical application of the treatment unattractive because surfactants tend to be adsorbed within the formation. This adsorption would necessitate using large quantities of surfactant if all of the flood water were treated to contain a given surfactant concentration, even if this concentration were quite low. Preston and Calhoun suggested that the principles of chromatography could be applied to the use of surface-active agents as a means of increasing oil recovery. A small volume of surface-active material is injec-

By K. A. Smith, X. Cheng

Introduction The separation of minerals from complex sulfide ores by flotation requires careful control of the surface chemical behaviors of the minerals constituting the ores. When the minerals in the ore are finely disseminated, extremely fine grinding is needed to liberate the minerals. Fine grinding is not only an energy-intensive operation, but also influences the flotation behaviors of liberated minerals. Steel balls are commonly used for grinding. Galvanic interactions occur not only between sulfide minerals and grinding media but also among the different sulfide minerals themselves. The electrochemical characteristics of chalcopyrite and pyrrhotite when they are independently coupled with steel grinding media and the relevance of these characteristics to the flotation behavior of these minerals have been exten¬sively studied (Cheng and Iwasaki, 1992: Li and Iwasaki, 1992). These studies dealt with reactions in two electrode combinations, simulating mineral-grinding medium and mineral-mineral interactions. In practice, however, it is more common to involve more than one sulfide mineral. In a study of a pyrite-pyrrhotite-mild steel system, Pozzo et al. (1989) provided evidence that a mineral having an intermediate potential could behave differently, depending on the condi¬tion of galvanic contact. This investigation was undertaken to study a chalcopyrite-pyrrhotite-mild steel system to gain better in¬sight into the mechanism of multiple galvanic interactions. A three-electrode system was chosen to simulate a typical copper sulfide ore. The sulfide minerals were represented by chalcopyrite and pyrrhotite. The grinding medium was rep¬resented by mild steel. The nature of galvanic interactions involving these minerals and grinding medium in an oxygen atmosphere was investigated in a three-electrode combina¬tion, and an attempt was made to relate the laboratory flotation results of pyrrhotite-chalcopyrite ores. Possible implications to the differential flotation of complex sulfide ores are discussed. Key words: Electrochemistry, Flotation, Sulfide ores Experimental The pyrrhotite (57.74% Fe, 0.09% Cu, 4.84% Ni and 36.54% S) sample was obtained from Falconbridge Ltd.'s Strathcona mine, Ontario, Canada, and the chalcopyrite (26.00% Cu, 28.57% Fe, 0.05% Ni and 31.52% S) sample came from Transvaal, South Africa. Mild steel (AISI 1020, 0.2% C) was chosen to represent grinding media. A conventional three-electrode cell was used in the elec¬trochemical measurements. The working, counter and refer¬ence electrodes were, respectively, sulfide minerals or mild steel, graphite rod and saturated calomel electrode (SCE, 0.245 V vs. standard hydrogen electrode). The exposed areas of the sulfide minerals and grinding medium electrodes were approximately the same (0.17 to 0.19 cm2). The preparation methods of working electrodes, the reagents used, the experi¬mental procedures and the instrumentation were the same as those described previously (Cheng and Iwasaki, 1992). Rest potentials of pyrrhotite, chalcopyrite and mild steel were measured individually in 0.05-M sodium sulfate solu¬tions. Combination potentials and galvanic currents of the sulfide minerals and grinding medium were measured in short-circuited two- and three-electrode systems. All poten¬tials in this study are quoted in volts with respect to the standard hydrogen electrode (SHE). To simulate the constantly abrading conditions in a ball mill, rest potentials, combination potentials and galvanic currents were also measured by rotating a porcelain ball against chalcopyrite, pyrrhotite and mild steel electrodes in

Jan 1, 2000

By E. B. Snyder, H. M. Kraner

This paper shows that volume stability, low porosity and decreased pyroplasticity are desirable for blast-furnace linings, partitularly for the hearth. It shows further that a hot load test is a valuable means of testing the fusion or softening behavior of a refractory at operating temperatures. The effect of carbon monoxide on commercia1 blast-furnace refractories in their as-received condition and after refiring is reported, showing that many commercial blast-furnace refractories disintegrate badly but that refiring decreases the effect and certain special refractories are now available which are almost free of the tendency. Factors Affecting Choice of ._ Refractories If one were to depend entirely upon experience or trial in the selection of clay refractories, the solution of a problem would be a slow process. Furnace campaigns are so long and attended by so many variables that it is difficult to draw fine distinctions within a reasonable period of time in regard to the quality of refractories used. It could be said, of course, that if service results do not yield the proper information for intelligent choice, there is no difference in the quality of brick being considered, but this is not necessarily true. Conventional ceramic tests are designed to give the ceramic engineer information as to the refractoriness and firing tempera- . ture, which he in turn internrets in terms of volume stability, ability to withstand load at high temperature (pyroplasticity), permeability, chemical stability and re-. sistance to the action of slag. In most refractory applications . several of these factors are involved. In a particular instance, one requirement may be predominant, while in others some other factors may be of primary importance. In this country, clay refractories are generally made from mixtures of plastic and flint fire clays. The process of firing a clay refractory is one of slowly melting the constituents, and during this operation its porosity is gradually reduced. The process is arrested, of course, in its incipient Stages and the Progress is determined by measuring slight changes in porosity, volume, bulk gravity, etc., that have taken place. Often the temperatures to which clay refractories are exposed in service are higher than those employed in their firing. However, if the manufacturer were to fire them at such high temperatures the brick would distort. Therefore it would be difficult for the manufacturer to fire all of his clay refractories to temperatures at which they are to be used, although in many cases it would be desirable from the user's point of view if he would do so. The porosity of clay refractories decreases by firing, to a minimum limit, after which a further increase in the temperature causes expansion in certain clay constituents and bloating in others. Both may occur in the same refractory containing two such clays.

Jan 1, 1944

By H. M. Kraner, E. B. Snyder

This paper shows that volume stability, low porosity and decreased pyroplasticity are desirable for blast-furnace linings, partitularly for the hearth. It shows further that a hot load test is a valuable means of testing the fusion or softening behavior of a refractory at operating temperatures. The effect of carbon monoxide on commercia1 blast-furnace refractories in their as-received condition and after refiring is reported, showing that many commercial blast-furnace refractories disintegrate badly but that refiring decreases the effect and certain special refractories are now available which are almost free of the tendency. Factors Affecting Choice of ._ Refractories If one were to depend entirely upon experience or trial in the selection of clay refractories, the solution of a problem would be a slow process. Furnace campaigns are so long and attended by so many variables that it is difficult to draw fine distinctions within a reasonable period of time in regard to the quality of refractories used. It could be said, of course, that if service results do not yield the proper information for intelligent choice, there is no difference in the quality of brick being considered, but this is not necessarily true. Conventional ceramic tests are designed to give the ceramic engineer information as to the refractoriness and firing tempera- . ture, which he in turn internrets in terms of volume stability, ability to withstand load at high temperature (pyroplasticity), permeability, chemical stability and re-. sistance to the action of slag. In most refractory applications . several of these factors are involved. In a particular instance, one requirement may be predominant, while in others some other factors may be of primary importance. In this country, clay refractories are generally made from mixtures of plastic and flint fire clays. The process of firing a clay refractory is one of slowly melting the constituents, and during this operation its porosity is gradually reduced. The process is arrested, of course, in its incipient Stages and the Progress is determined by measuring slight changes in porosity, volume, bulk gravity, etc., that have taken place. Often the temperatures to which clay refractories are exposed in service are higher than those employed in their firing. However, if the manufacturer were to fire them at such high temperatures the brick would distort. Therefore it would be difficult for the manufacturer to fire all of his clay refractories to temperatures at which they are to be used, although in many cases it would be desirable from the user's point of view if he would do so. The porosity of clay refractories decreases by firing, to a minimum limit, after which a further increase in the temperature causes expansion in certain clay constituents and bloating in others. Both may occur in the same refractory containing two such clays.

Jan 1, 1944

By Ramon S. Pizarro, W. Joseph Schlitt

Introduction Trying to synthesize innovations occurring in gold processing is not simple. At present, this technology is exploding, brought about by the high price of gold. This price has compelled the mining industry, as a matter of survival, to produce gold. The frantic search for gold deposits continues, from glacial areas to tropical jungles. The search has been fruitful. New exploration techniques have helped to locate deposits. Some are amenable to conventional processing techniques. Others are in unusual settings that challenge the ingenuity of extractive metallurgists. Ore deposits containing traces of invisible gold, refractory mineralization, and impurities and deleterious materials that previously defied treatment are now being profitably processed. Metallurgists have developed various processing methods and equipment for gold ore treatment that reflect differences in ore characteristics, grade, mineralogy, reserves, topography, climate, and location. These processes can be categorized as: • For nonrefractory or readily leachable gold ores - vat leaching, heap leaching, and agitation leaching. • For ores containing free gold - gravity concentration methods, followed by mercury amalgamation, and • For refractory gold ores - flotation, roasting, pressure oxidation, followed by cyanidation leaching. In actual practice, a combination of these processes may be required. This is because gold mineralization, although usually simple, may be associated with other mineral species or with clays that make the ore difficult to treat. Furthermore, after the gold has been solubilized to form a cyanide complex, one of two important processes must be applied to recover the gold. These ore zinc cementation (Merrill-Crow process) and Carbon adsorption, desorption, and electrowinning. New techniques for leaching and recovery are also advancing. These will become the bases for the next generation of gold processing plants. Nonrefractory Gold Ores Nonrefractory ores with readily leachable gold are among the .easiest to treat. Even so, non-refractory ores from epithermal deposits are likely to contain too much clay. When these ores are damp, they may clog the screens and cone crushers. Depending on the type of process, scrubbing the crushed ore is very effective in overcoming clay problems. After dewatering, the slimes enter the cyanidation process and the thickener overflow is stripped of gold values and recycled. Semiautogenous (SAG) mills are also gaining popularity due to lower capital costs and ability to treat wet, sticky ores. If properly sized, the secondary crushing and screening plants, together with a secondary ball mill, can be eliminated. When the ore is of such a low grade that it can not support fine grinding, vat or heap 'teaching may be applicable. These systems are being actively applied in the US and elsewhere. Rapid construction and low capital costs are important features of these plants. Vat leaching is ideally suited for fast leaching ores and small tonnage deposits located in areas with harsh winters or wet tropical climates. For effective vat leaching, the ore is crushed to less than 25 mm (1 in.), agglomerated with lime or cement to control fines, and leached with sodium cyanide solution (upflow or downflow). The degree of size reduction is a tradeoff between increased costs of comminution and improved gold recovery from smaller particles. However, the size of material

Jan 11, 1984

By E. N. Aqua, C. M. Owens

The microstructure in cold-rolled Zircaloy-4 sheet has been characterized by transmission electron microscopy and X-ray diffraction line-broadening techniques. The rate of work hardening is measured in terms of microstrains, particle sizes, micro hardness, the tensile yield strength. The tensile yield strength of Prestrained (less than 10 pet) Zircaloy-4 sheet is found to be a linear function of the square root of the dislocation density, us predicted by work-hardening theories. ZIRCALOY is one of the most important structural alloys for nuclear reactor applications.''2 In order to understand the effects of the nuclear environment on Zircaloy structural members, the preirradiation microstructure must be characterized. This report will describe the substructure existing in cold-rolled Zircaloy-4 sheet as observed by electron microscopy and by X-ray diffractometry. I) EXPERIMENTAL PROCEDURE Commercial Zircaloy-4 strip was cold-rolled and annealed in argon at 760°C for 1 hr. The annealed sheet was again cold-rolled to a maximum of 50 pct reduction in thickness with segments of the strip being retained after 2.5, 5, 10, and 20 pct reductions. One-inch-square portions were chemically polished (50 parts HNO3, 50 parts H2O, 10 parts HF) and mounted onto lucite blocks using double-sided tape to prevent bending during handling. Thin foils suitable for transmission electron microscopy were prepared from each of the sheet samples. The sheets were mechanically polished through 600-grit paper to a 3 to 4 mil thickness and were chemically polished by immersion for 1 to 2 min in a solution containing: 50 parts HNO3, 50 parts H2O, and 10 parts HF, and rinsed in distilled water. The final metallographic procedure was to electropolish for less than 10 sec with an electrolyte of 10 parts perchloric acid and 90 parts glacial acetic acid, at 20 v, at room temperature using stainless-steel point cathodes and a vigorous stirring action. These foils were examined in a Philips EM 200 electron microscope using a 100-kv accelerating voltage.

Jan 1, 1968

By B. R. Schneiders

"Atikokan is 200 km west of Thunder Bay and earned its mining fame from the discovery of the Steep Rock Iron Range in the late 1930s. Gold, however, was discovered in the Atikokan and Mine Centre areas in the late 1800s and eventually led to one of Ontario's first gold camps, and a total production of approximately 52,000 oz of gold and 174,000 oz of silver from 218,000 tons milled.The general geology of the area consists of Early Precambrian rocks of the Wabigoon and Quetico subprovinces, separated by the east-trending Quetico Fault. The Wabigoon Subprovince, to the north, consists of metavolcanics, minor metasediments and granitic batholiths. The Quetico Subprovince consists of metasediments and granitoids. Small ultramafic plutons occur throughout the metasediments.Within a 50-km radius of Atikokan, more than 50 gold occurrences, prospects and past producers have been discovered since the 18oos. The Atikokan Gold Study performed by the Ontario Geological Sur vey (Wilkinson, 1980, 1982) defined three types of gold mineralization in which gold is concentrated in quartz and quartz-carbonate veins:I) Metavolcanic-Hosted, Stratabound Type-associated with altered felsic fragmental units and chemical sedimentary rocks; possible gold mineralization source rocks. The mineralization is due to metamorphogenic (epigenetic) enrichment. Associated with dynamic metamorphism events and/or felsic intrusive events.2) Marmion Lake Batholith Type-occurs within the gneissic core of the batholith associated with north east-trending lineaments, representing faults or shear zones. Mineralized veins are related to several periods of deformation and shearing, suggesting that metamorphogenic veins were produced during dynamic metamorphism.3) Contact Zone Type -occurs in the contact zone rocks between gneissic batholiths and meta volcanic belts. Hydrothermal solutions produced during several deformational periods acted to leach and concentrate gold mineralization. Localized, discontinuous shear zones host the epigenetic (metamorphogenic) veins.Twenty-one properties in the area were mapped and sampled, and researched petrographically and geochemically. Geological data from the Atikokan Economic Geologist Program of the Ontario Geological Survey are used in discussing the types of mineralization, genetic models, and exploration targets and techiques."

Jan 1, 1983

By G. Y. Chin, M. T. Dolan, W. L. Mammel

In the case of plastic deformation by slip, von Mises&apos; showed that an arbitrary shape change of a crystal generally requires the activation of five independent slip systems. The selection of the five active systems was worked out by Taylor ,&apos; who hypothesized that, among all combinations of equivalent slip systems which are capable of accommodating a given imposed strain, the active combination is that one for which the sum of the absolute values of the glide shears is a minimum. Taylor analyzed the case of {lll}( 110) slip for fcc metals and applied the analysis to crystals undergoing axisymmetric flow, which approximates the shape change of an embedded grain in a polycrystalline aggregate deformed in tension (or compression). For the twelve equivalent (111) (110) slip systems, there are 384 independent combinations of five slip systems that satisfy the imposed strain.&apos; Taylor laboriously calculated the value of M = ZjIyj /E for each combination (although some were missed) and obtained the minimum M, hence the active combination, for a number of axial orientations distributed throughout the stereographic triangle. (yj is shear from slip on the th system and e is the tensile strain). Detailed contours of constant minimum M were recently obtained by Hosford and Backofen using a simplified but equivalent Bishop and ill&apos; analysis. Due to the numerous combinations of slip systems involved in the calculations, however, the full potential of the powerful Taylor analysis has not been exploited. For this reason, we have recently utilized techniques of linear programming to obtain solutions of the Taylor analysis for axisymmetric flow, for slip on {110)(< 111), {112)(111), and {123)(111) systems as well as mixed slip composed of these three systems. These slip modes are of obvious importance in the deformation of bcc crystals. Some of the salient results are summarized below. 1) Stress-Strain Data for Polycrystal. The value of M averaged over all axial orientations is the ratio of the tensile flow strength of a randomly oriented aggregate to the critical resolved shear stress for slip. This value enters importantly in theoretical deductions of the polycrystalline stress-strain curve from single-crystal data.2&apos;3&apos;5 Table I lists the values of Ma,, for the several cases of slip, as obtained by the present computer work. 2) Texture Hardening. Since the value of M depends on the axial orientation, the (tensile) flow strength of a specimen may be increased through texture control.&apos; An example of the computer results is shown in Fig. 1, where contours of minimum M have been computer-plotted for the case of mixed slip on {110}(111), {112)(111),and {123}(11 1) systems. It may be seen that, under axisymmetric flow, wires of (111) and (110) axial orientations are 50 pct stronger than those oriented at (100) .

Jan 1, 1968

By Pelin Altinkaya, Maria Leikola, Jussi Liipo, Mika Haapalainen, MARI LUNDSTROM, Eero Kolehmainen

Chloride leaching has many advantages compared with other alternative processes to cyanidation because it has increased metal solubility, improved redox behavior and high leaching rate properties. Also, chlorination is a nontoxic and environmentally friendly process, which is sought by the mining and metallurgy industry. In addition to these advantages, chloride is an effective reagent for the dissolving of metals from refractory ores and process residues that have trace amounts of valuable metals waiting to be valorized. 

By L. Burris, G. A. Bennett, P. A. Nelson

Staznless steels ave rrzuch less seuel-ely attacketl by zinc lapov than by molten zinc systems. To determine the applicubility of stainless steels fov equipment items which would be exposed only to zinc vapor, the corvosion resistance of several stainless steels to zinc vapor was investigated in 500-hr- exposuves at 900° C. Two austenilic stainless steels, Types 304 and 3-17, suffered severe intergranular attack. Loss of nickel from these steels and micro-probe crnalyses indicated the probable formation of low-melting zinc-rich phases. Good vesistance to attack by zinc vapor, as determined by metallo-9-rpaphic excr)rtination and physical testing, Loas exhibited by Type 405 stainless steel, a jevvitic steel. Type 440C stainless steel, a tnartensitic steel, although suffering considevable loss in weight, was not structurally weakened. At Argonne National Laboratory liquid zinc and zinc-rich alloys are being employed as solvent media in pyrometallurgical processes under development for recovering and purifying discharged reactor-fuel materials.&apos; Because of the high solubility of most metals in liquid zinc,&apos; there are few metals which can serve as container materials for liquid zinc at temperatures much above the melting point. The poor corrosion resistance of the common metals and alloys to molten zinc has been discussed by Eldred.3 DeKany, Lavendel, and Burris4 tested some of the less-common alloys of the nonrefractory metals and found that they also have poor resistance to attack by liquid zinc and Zn-Mg solutions. Of the metallic materials, only some of the refractory metals such as tantalum, tungsten, and molybdenum and their alloys have shown resistance to attack by liquid zinc.4-7 In the process-development work at Argonne National Laboratory, tantalum and tungsten vessels have been used to hold liquid-zinc alloys. These vessels are housed in stainless-steel equipment, principally to permit maintenance of an inert atmosphere and operation at various pressures. In this experimental work, it has often been observed that Type 304 stainless steel suffers little attack by zinc vapor at temperatures up to about 800 °C. In contrast, severe attack occurs in areas where zinc condenses as a liquid. The extent of attack by zinc vapor on several stainless steels was investigated because there are possible useful applications of stainless steel for equipment items which would be exposed only to attack by zinc vapor. These applications include, for example, housings around processing equipment as indicated above and vapor lines leading from zinc stillpots or retorts to condensers. EXPERIMENTAL EQUIPMENT AND PROCEDURE The experimental procedure consisted in exposing stainless-steel test coupons to static zinc vapor for 500 hr at a temperature of about 900°C. The apparatus, shown in Fig. 1, consisted of a 12-in.-long closed tantalum tube jacketed in Type 304 stainless steel to prevent oxidation of the tantalum. A Zn-10 wtpct Mg* alloy charge of 293 g in the bottom of the

Jan 1, 1965

By D. L. Wood, J. H. Westbrook

The tensile behaviors of the CsCl structure compound AgMg are extensively documented in terms of strain, strain rate, temperature, composition, and metallurgical processing treatment. The observations lend themselves to presentation in terns of three regimes of deformation behavior; 1) low temperatures where deformation is primarily by slip; 2) intermediate temperatures where the deformation mode is also slip but with the detailed behavior dominated by dislocation interactions with solute atoms; 3) high temperatures where defomation is primarily by diffusion controlled processes. Of all the material groups of potential interest as high-temperature structural materials, the inter-metallics have been the least studied, particularly with respect to their mechanical behavior. Moreover, the application and processing of intermetallics for uses which exploit their often unique physical properties have been impeded by a lack of understanding of their mechanical properties. Previous work in this area* has been largely *For a recent review, see Westbrook.&apos; exploratory, aimed on the one hand at the direct empirical development of materials of engineering utility and ,on the other at identification of the important parameters affecting the mechanical behavior of inter metallics. As a consequence, there has not been available, heretofore—for any inter-metallic—data, sufficient in extent or precision to provide an adequate phenomenological description of the effects of metallurgical variables on deformation behavior. Such documentation is prerequisite to intelligent application or processing design and is also necessary for testing present and future theoretical analyses of mechanical behavior. It was therefore an objective of the present investigation to document the deformation behavior of a simple ordered intermetallic over as wide a range as possible of all the usual metallurgical variables. The compound AgMg was chosen as the subject of this investigation because it met all of a group of desired criteria, namely: 1) congruent but moderate melting point; 2) simple crystal structure; 3) ordered structure persisting to the melting point; 4) broad solubilities for the component elements. The first and last criteria were expected to aid in the preparation of homogeneous single-phase specimens: the second and third to help simplify the

Jan 1, 1962