Search Documents

By E. E. Wark, I. W. Wark, J. Rogers. K. L. Sutherland

Soaps have hem used as collectors for many years, but only in the last eight years have other long-chain paraffin salts been used. It may be anticipated that these newer collectors will be used mainly with nonsulphide minerals, for which the xan-thates and similar compounds are of little value. On the other hand, the xanthates are both cheap and effective for sulphide ores and seem likely to retain their present cminence in this field. During 1938 and 1939 two of us (E. E. W. and I. W. W.) commenced a comprehensive investigation of the principles underlying the use of paraffin chain salts as flotation reagents. This research was sponsored jointly by the University of Melbourne and a group of Australian mining companies. † A broad, semiquantitative survey was then made of the field covered in the present paper. This was followed in 1940 by further work by one of us (K. L. S.). In 1941 the investigation was taken over by the Division of Industrial Chemistry of the Commonwealth Council for Scientific and Industrial Research, Australia. Discovery of some principles upon which are based the flotation of minerals by paraffin chain salts was followed by their application in the development of processes for the recovery of certain strategic minerals from their ores. Promising results in the flotation of cassiterite from various ores will be described in a subsequent paper. The Paraffin Chain Salts 'he basic requirements for a "collector " in flotation are that it should form a film over the surface of the mineral to be floated, and that this film should be orientated so that hydrocarbon (nonpolar) groups form the effective surface. When modified in this way, the mineral surface possesses some degree of air avidity. All investigators would agree with Taggart, Taylor and Ince23 that such a film can be produced only if the collector compound contains an active (polar) group to attract it to the mineral surface as well as the nonpolar group. One section of this large class of polar-nonpolar compounds is the paraffin chain salts: CH3(CH2)nX where .X signifies a polar group that ionizes in aqueous solution. Though the compound can ionize, it may be a weak or a strong electrolyte, and the hydrocarbon chain may be in the cation or the anion (Table I). Many compounds of similar constitution are available, but the usual polar groups are: -Co2Na, -So3Na, -So4Na, — PO4Na2, or an aminonitrogen group, the

Jan 1, 1947

By Zorigtkhuu Davaanyam, Fisher Wang, Bern Klein, Amit Kumar

"The High Pressure Grinding Roll (HPGR) is an increasingly popular energy efficient solution for comminution of competent ore deposits that primarily competes with conventional crushers and tumbling mills. A significant barrier to increased adoption of HPGRs is the requirement for large amounts (one tonne or more) of sample for pilot testing which may not be feasible for most early staged projects.Various researchers have worked towards developing piston-die and JK drop weight tests to model and predict the energy requirements for an HPGR. Two small scale laboratory test procedures (the SMC test (Morrell, 2009) and the piston press tests (Davaanyam, 2015)) have been developed in recent years to provide necessary information to size an HPGR.These two methods were used to estimate the required specific energy for an HPGR unit and compared to HPGR pilot scale test results from a copper deposit. The comparison provides insight into the benefits and limitations of these tests.INTRODUCTIONHigh pressure grinding rolls (HPGR) have gained popularity in recent years because of their energy efficiency in comminution. Various researchers have suggested that approximately 50–80% of the total energy consumed in a mineral processing plant is used by the comminution equipment (Haque, 1999; Abouzeid & Fuerstenau, 2009; Wang, 2013). Haque (1999) showed that the efficiency of grinding equipment can be as low as 1%. Due to the energy intensive nature of comminution, mining industry has been forced to explore alternative energy efficient processes.An HPGR based circuit has been shown to be 10–25% more energy efficient than a conventional SABC circuit (Von Michaelis, 2009; Wang, 2013). A significant barrier to the increased adaptation of HPGRs is the requirement for a large amount of sample for pilot testing (up to 5 tons), even on a prefeasibility level. Numerous studies have been performed to utilize piston press test to analyze the performance of the HPGR circuit and to predict the energy consumption for an industrial application. This paper uses two small scale laboratory test procedures, the SMC test and a piston press test, to compare the energy requirement to the pilot HPGR data."

Jan 1, 2016

By L. D. Wooddy, W D. Moore

Water drives may be natural or artificial. For the case of a natural water-drive reservoir, the volume of water influx corresponding to reservoir pressuve-production history may be calculated by means of the material bal-ance-unsteady state equation. For the artificial water drive or pattern injection water flood, the material balance equation is sufficient to determine the reservoir pressure-production, injection history. However, for both cases to reliably predict reservoir performance, it is necessary to calculate the saturation distribution of the reservoir fluids at different stages of depletion. This paper consolidates the various equations used to determine the performance of water-drive reservoirs into one approach that is applicable to any reservoir that has a natural water drive or is to be produced by water injection. The numerical procedure has been simplified considerably, and the solution is adaptable to either hand calculations or digital computer operation. INTRODUCTION A water-drive reservoir is one in which the predominant source of energy for production of oil results from the encroachment of water into the oil zone. The water drive may be either natural or artificial. Water invasion takes place by expansion of water in the aquifer as a result of the pressure decline transmitted from the oil reservoir. Because water is practically incompressible, a natural water drive requires an extensive aquifer containing a volume of water many times the volume of oil in the reservoir. Provided the permeability of the formation is reasonably high, a moderate decline of reservoir pressure usually causes adequate water influx. If the reservoir pressure decline becomes excessive because of low permeability or a high rate of production, part of the oil production may result from the liberation of dissolved gas which may cause excessive quantities of free gas to be produced along with the oil. In extreme cases, reservoir pressure may decline so rapidly as to cause the oil to be produced predominantly by dissolved gas drive, leading to abandonment of the reservoir before the advancing water has had a chance to flush the entire reservoir. In reservoirs that are not connected to extensive aquifers, an artificial water drive may be created by injecting water into or around the lower edges of a reservoir. Sometimes water is injected within the reservoir through wells interspersed among the producing wells. When injection is carried out in such fashion, the reservoir is in effect subdivided into a number of separate producing segments, in each of which the displacement of oil is simultaneously taking place, and the shapes of which are fixed by the well patterns employed. Because of the natural tendency of oil and water to segregate according to their relative densities, water will tend to migrate downdip regardless of where injected. Accordingly, the injected fluids can be retained within the intended reservoir segments only when conditions are unfavorable to their migration under the force of gravity. Pattern injections are usually confined, therefore, to reservoirs having low structural relief, or low permeability, or when production and injection rates are such that fluid movements in the reservoir are dominated by the pressure gradients rather than by the force of gravity. In the case of natural water-drive reservoirs and artificial water-drive reservoirs in which the water is in-

Jan 1, 1958

By Francis Crowley

Elementary concepts of seismic wave properties are reviewed to establish a framework for discussing seismic noise and its suppression. A liberal number of references is included for those who wish to pursue the topic in detail. A base motion noise level is established for a single surface seismometer. It is argued that simple array processing and seismometer burial should regularly permit us to approach this base noise level which is found in areas free of conspicuous man-made seismic noise sources. The sensitivity of the base seismic level to a number of common disturbances is presented. Solutions that promise to hold the "effective" seismic noise at a site near the base level are given for acoustic, meteorological and fixed local surface sources. Guidelines are suggested for controlling other local man-made sources, e.g. vehicular traffic, by keeping them at sufficiently large distances away from the seismometers to keep noise at permissible levels. These guidelines are speculative and conservative. They should be the subject of future study. The ability to process against general local activity, drilling, and intra- mine sources is limited. Certainly no dramatic gain is to be expected. When strong man-made and/or intramine noise sources are not controllable, detection may well be impossible to achieve, unless the seismometer can be moved close enough to the suspected miner position, i.e. via very deep holes, to compensate for the likely vast differences in strength of the miner signal and the uncontrollable man-made noise sources. However, many intramine sources, e.g., falling water, rock bursts, explosions, etc., may well preclude the existence of a hale miner in their vicinity, and therefore any need to attempt detection of a miner at such locations. The following recommendations are made to enhance the detection and location of a miner signaling seismically. They are: 1. Seismometer burial in slim holes. 2. Narrow band detection, using multiple narrow band filters to cover the likely signal band. 3. Broadband recording and analysis for time-of-arrival estimation.

Jan 1, 1974

By M. Hansen, C. C. Wang

THE 6 phase of the Cu-Sn system (Cu,Sn, = 32.53 pct Sn) was considered to be stable down to room temperature until Owen and Iball showed by X-ray analysis that it undergoes a eutectoid decomposition into the a and e phases at a temperature near 300°C. Their findings have been confirmed by other investigators,2-5 a11 of whom used X-ray diffraction studies of powdered specimens. The transformation temperature has been reported by various authors as lying between 300" and 380°C. To our knowledge, no microscopic evidence of the eutectoid reaction has been published, as yet. It was in connection with other work that longtime annealings at 300°C were conducted with alloys containing 22, 32.6, and 35 pct Sn (nominal compositions) prepared from electrolytic copper and electrolytic tin and cast in a small iron mold. The specimens were first annealed at 700°C for 5½ hr and quenched from 400 °C after cooling to, and annealing at, that temperature for 9½ hr. After this treatment the sample with 22 pct Sn was cold worked for 15 pct reduction in thickness; the 32.6 and 35 pct alloys were too brittle to be cold worked. The final anneal at 300°C was done in a sealed pyrex glass bulb for 63 days. Fig. 1 represents the microstructure of the annealed alloy with 22 pct Sn. It shows primary a solid-solution crystals in a matrix of the (a + 8)-eutectoid formed at 520 °C. The a crystals contain 8 inclusions which precipitated from a due to the decrease in the solubility of tin in copper with fall in temperature. The decomposition of the 8 phase into a (light) and E (dark) can clearly be seen in some areas of the (a + 8)-eutectoid matrix. However, the decomposition is far from being completed, even after the long-time anneal used. Figs. 2 and 3 depict the microstructures of the annealed 32.6 pct alloy, which was intended to consist entirely of 6 phase. Due to some loss in copper on melting, the composition is slightly higher in tin. Accordingly, the sample after quenching from 400 "C consisted of grains of the 8 phase with the e phase arranged along the grain boundaries and as a Wid-manstatten precipitate within the 6 grains. After an annealing time of 63 days, the eutectoid decomposition, 6 + a + e, is still in its early, initial state. The pearlitic type of eutectoid is nucleated at the c crystals, preferably those surrounding the grain boundaries of the 8 phase. The appearance of the (a + €)-eutectoid in the 35 pct Sn alloy was very similar to that shown in Figs. 2 and 3. Again, the eutectoid decomposition nucleated at the 6 phase and proceeded from there into the 8 areas. As is evident from Fig. 2, the rate of decomposition of the 6 phase at 300°C is extremely sluggish: In the representative area shown only about 5 pct of the 8 phase has undergone the eutectoid trans- formation after annealing for 63 days. On the other hand, Owen and Williams2 have reported that X-ray photographs of powdered samples with between 17.5 and 34 pct Sn did not show 8 lines after annealing for only five to seven days at 300°C. This is in accordance with the fact that the rate of reaction in powdered samples is higher than in massive specimens, as a result of the excess free energy of the powder (due to its greater surface area). The authors wish to express their thanks to C. A. Johnson for preparation of the micrographs.

Jan 1, 1952

By W. M. Reilly, Martin E. True, O&apos

A technique, equipment, and a compound have been developed and field tested for sealing tubing joint thread leaks without removing the tubing from the well. This eliminates the necessity of killing the well with possible damage to the producing formation, which could result if it were exposed to drilling mud. A thread sealing compound, developed and tested in the laboratory, is introduced into the tubing and squeezed into the joint to eliminate the leak. A high percentage of successful field applications have eflected an appreciable cost reduction in repairing leaking tubing strings in East Texas and in the Louisiana Gulf Coast area. INTRODUCTION In producing oil and gas wells the industry has been plagued with a never ending problem of tubing connection leakage. This situation is becoming increasingly more significant as more gas wells are placed on production and as higher pressures are encountered at greater depths of current drilling. Substantial progress has been made in minimizing thread leaks by careful handling and cleaning of joints and by the use of improved sealing compounds in combination with controlled makeup. But even with the use of the best known methods and sealing materials during initial makeup, occasional leaks through tubing joint threads appear inevitable. In some instances, tubing joints in high-pressure gas wells have been found to leak gas at relatively less pressure than that at which the tubing had been tested satisfactorily using liquid. Many expedients have been employed to prevent the physical replacement of tubing when leaks have developed. Perhaps the most commonly used is the sodium silicate treatment in which the solution is lubricated into the tubing to form a crystalline plug in the leak. Generally, any benefit realized is of a temporary nature. In addition to field studies on handling and makeup of tubing, extensive laboratory work has been undertaken on the development and testing of thread dopes.' Also, substantial effort has been devoted to testing tubing joints using high-pressure gas as a pressure medium.' The results of this work have emphasized that tubing joints are susceptible to occasional leaks, especially when subjected to relatively high differential pressures. To cope with the problem of leaking connections, an extensive investigation was undertaken to devise means of sealing leaks without removing the tubing from the well and without reducing the inside diameter of the tubing. The purpose of this paper is to present a technique, together with the associated equipment and compound, which have been developed for effecting a seal of leaking tubing in place. DISCUSSION Work was initiated simultaneously on two ventures: (1) to develop a satisfactory leak sealing compound and (2) to develop tools necessary to find the leak and place the compound. Leak Sealing Compound In the development of a sealing compound, tests were conducted on those compounds commercially available which include: (1) conventional thread lubricants, (2) thermo-setting resins and (3) other materials which held promise of effecting a seal. Although none proved completely satisfactory in their available form, two commercial compounds proved nearly equally effective in sealing leaks during laboratory tests after proportioned quantities of graded silica had been added. Field usage has indicated that the preferred compound is one prepared of an aluminum-stearate base thinned to the proper constituency and carrying a mixture of fine mesh graphite and graded silica. The compound developed by Humble Oil & Refining Co. is designated as Tubing Thread Leak Sealant 800. Placement Tools and Technique In developing tools to detect joint leaks and to place the sealing compound, work was done initially on wireline equipment. Preliminary designs were completed of a tool somewhat on the order of a pressure bomb to test individual joints with gas at high pressure to determine if the joint was leaking. An entirely different tool equipped with opposed packers was intended for placement of the sealing compound at high pressures in each leaking joint. The application of these tools

Jan 1, 1958

1. Book reviews Tungsten: 1982. London, Mining Journal Books Ltd, 1982. 179 pp. Reviewer: G.A. Brown The geology of industrial minerals in Canada, edited by G.R. Guillet and Wendy Martin. Canadian Institute of Mining and Metallurgy, special volume 29. Reviewer: R.W.O. Kersten Foam flotation - theory and applications, by Ann N. Clarke and David J. Wilson. New York, Marcel Dekker, 1984. 418 pp. Reviewer: B.K. Loveday Industrial and financial indicators of the steel industry, by Patrick Genevaz. Paris, La Chambre des Cartes, 1982. 2 vols. Vol I: Analysis and conclusions, FF3500. Vol. 11: Tables, FF4000. Reviewer: R.J. Dippenaar An encyclopaedia of metallurgy and materials, by C.R. Tottle. Plymouth, Macdonald and Evans and The Metals Society, 1984. 481 pp. RI44,50. Reviewer: P. T. Wedepohl The role of crack growth in metal fatigue, by LP. Pook. London, The Metals Society. Reviewer: C.A. Boothroyd Hydraulic coalmining - new technology and its geological and industrial significance, by H.C. Siebert. Hamm, Zentraldruckerei BAG, 1984. 33 pp. Hydraulic coalmining - hydromining update: potential impact on coal deposits and coal mining industry, by H.C. Siebert. Hamm, Zentraldruckerei BAG, 1984. 130 pp. Victoria's brown coal. A huge fortune in chancery, edited by J .T. Woodcock. The Australasian Institute of Mining and Metallurgy, 1984. 204 pp. Reviewer: J.J. Versluis 2. Canadian publications The following reviews of the activity and developments during 1982 in respect to the chief minerals produced or consumed in Canada are now available. Zirconium. An important mineral commodity. Mineral Policy Sector, Mineral Bulletin MR 202, $6.60. Canadian minerals yearbook 1982. Mineral Policy Sector, Mineral Report 32, $40.75. Canadian reserves of copper, nickel lead, zinc, molybdenum, silver and gold as of January 1, 1983, by W.H. Laughin. $4.20. Mineral Policy Sector, Mineral Bulletin MR 201. Sulphur market profile, by B.W. Boyd. Mineral Policy Sector, MRI 84/5. 3. Mintek publications Report M123 The use of of activated charcoal in a NIMCIX column for the recovery of gold from cyanide solutions. Report M150 Energy transfer in the hearths of submerged-arc furnaces. Report M151 A preliminary investigation of the initiation of pitting corrosion in austenitic stainless steels and nickel-based alloys. Report M154 The reduction of Winterveld chrome spinel at 1300°C under an argon atmosphere in the presence of carbon. Report M165 The development of an improved on-line gold analyser. Report MI67 three nebulizers for use with an inductively coupled plasma spectrometer. 4. New publications Mineral Industry Consultants Association (as at 31st March, 1984). Parkville (Australia), The Australasian Institute of Mining and Metallurgy, 1984. 112 pp. Philosophical and procedural guidelines for the planning professions. Johannesburg, the Environmental Planning Professions Interdisciplinary Committee (EPPIC, P.O. Box 61019, Marshalltown 2107), R2.50. Directiona//y solidified materials for high temperature service, by M. McLean. London, the Metals Society, 1983. 337 pp. Tin and its uses no. 142. Greenford (England), International Tin Research Institute, 1984. Metals engineering International Symposia & Exhibitions Ltd - a subsidiary of Industrial Newspapers PLC - are pleased to announce that they will be organizing a mammoth engineering event, entitled Metals Engineering 86, comprising five important exhibitions in 1986:. Agglomeration A major symposium on agglomeration is being organized in Toronto for the 2nd to 5th of June, 1985. Speakers from around the world (Canada, U.S.A., Brazil, Australia, Japan, West Germany, Italy, India, China, Switzerland, Poland, Yugoslavia, and France) will address delegates on various aspects of agglomeration relative to iron ore, coal, coke, and fuels. Plenary theme papers will also be presented by speakers from Japan, the U.K., and the Netherlands.

Jan 1, 1985

J. B. Cohen (AVCO Mfg. Co.)-The model presented by the authors is only one of several possible mechanisms for low-temperature aging. It is true that the motion of dislocations to the copper atoms, followed by diffusion along the dislocation lines, is one such mechanism. However, the details of such a process which would :result in copper-rich platelets on (100) planes in the f.c.c. matrix are not clear. Furthermore, there is at least one other mechanism that may be used to e.xplain the authors' results, so that the data do not clearly favor the Turnbull model. The zones may form by "normal" diffusion. The diffusion constants would be higher at room temperature than extrapolated data would suggest due to vacancies trapped in the specimens in the quench. The diffusivity would then be multiplied by the ratio of the number of vacancies present at the solution temperature to that present at room temperature. These vacancies could remain in the alloy specimen for long times at room temerature, due to interaction with the copper atoms. ' The activation energy for diffusion is smaller than that for bulk diffusion at elevated temperatures for it is only that for the motion of vacancies existing after the quench; after these are used up, the aging process effectively ceases. It is somewhat questionable if the laws governing transformation kinetics can be directly applied to changes in elastic moduli, especially in the case of aging where the structure and the composition of the zones may be changing during aging, If such laws are assumed, it is possible to explain the exponential factor of % with this vacancy model. It is probable that the structure of the zones and the matrix match only on (100) planes. Certainly the precipitates that form in this system after various aging treatments show orientation relationships similar to those of the zones. Strains on the edges of the zone may set up fields which do not allow the zone to grow in an edgewise manner. The exponent in the growth of a thin plate in a direction perpendicular to its face would be %. It may also be that copper atoms are attracted to dislocations. If this is the rate-controllin factor in the growth process Ifthisthen an exponent of % or % may arise. The writer would like to know if the authors have tried plotting l/a; proportional to as might be expected for "dislocation drainage." R. H. Doremus (General Electric Research Laboratory)—An important new method for following the growth of Guinier-Preston zones is presented in this paper, and I wish to congratulate the authors on their experiments. Their interpretation of the results, however, is doubtful in certain respects. To determine the exponent m in Eq. [4] the authors plotted -log at against t to various powers (their Fig. 6). The initial value of frequency used for these plots was found by extrapolating the data to zero time. In Fig. A the data from their Fig. 2 are plotted against a linear, rather than logarithmic, time scale. To obtain graphs similar to their Fig. 6 for these data one must use an initial frequency of about 52720; such a plot for m = % is shown in Fig. B. The straight line in Fig. B fits the data in an intermediate range only. The curve drawn in Fig. A was mapped from this line; comparison of

Jan 1, 1960

By D. Turnbull, J. H. Hollomon

IN the most general sense, solidification refers to the formation of crystalline material from either a gas or a liquid. However, in this symposium, only the formation of crystals from liquids will be considered. Thus, in our present study the problem of solidification becomes that of determining the mechanism of the transition from a liquid to a crystalline solid, and our particular interest is in the transformation of metals from the liquid to the crystalline state. Metal liquids are seldom composed of only one kind of atom. Often solute atoms are added intentionally to make an alloy, or they may be present accidently because of incomplete purification. Furthermore, there may be small solid particles of various other crystals present in the liquid. Such small crystals may persist if their melting points are higher than any temperature to which the liquid is heated. Prior to solidification, the liquid metal usually is poured from one container to another. The second container, called the mold, usually is at a lower temperature than the container, or the crucible, in which the metal is liquified. The first solid that forms upon contact with the mold generally is of a different composition than the liquid, usually containing fewer foreign atoms or dissolved impurities. Heat is evolved upon solidification and is dissipated through the surroundings. Tree-like crystals, or dendrites, grow from the container walls and branch into the melt, enriching the remaining liquid in impurity atoms. In some alloys the remaining, relatively impure liquid continues to solidify until no liquid remains and the branches of the original crystal are cemented together. In other alloys, particles with a second type of crystal structure appear before solidification is complete. First the nature of the liquid and the solid states will be considered and then the mechanism of the initial formation of crystals from pure and alloy liquids. Later the problem of the growth of these crystals and the complexities of solidification in a mold, where the temperatures are not uniform and the composition of the melt changes continuously, will be discussed. LIQUID AND CRYSTALLINE STATES A liquid is an aggregate of atoms arranged with no apparent regularity (over distances of more than a few atom diameters). Nevertheless, any given atom generally has a definite number of nearest neighbors at definite distances, and thus order may be said to exist over a short range. In a crystal, on the other hand, a regular array of atoms continues for many hundreds or thousands of atom diameters, and a long-range order is apparent. Thus, a crystal having long-range order can be reproduced by linear translations for 10-5 cm or more of some fundamental unit possessing short-range order. A crude illustration of the difference between liquid and crystalline structures can be obtained by comparing the possible arrangements of oranges in a crate. If the oranges are simply dumped into the crate haphazardly until it is filled, the oranges will represent a static model of a liquid.

Jan 1, 1951

By P. Hudock

Thin films of PbS and CdS have been deposited on insulutiug- sapphire substrates by euzploying a subliwzation technique rising near-equilibriurum conditions in ultrahigh vacuum. Oriented polycrystalline PbS and CdS films on sapphire have mobilities approachitzg values characteristic of bulk crystals. In the case of CdS, special purification procedures were crucial in obtaining high-mobility films. By performing the depositiotz of a compound within a small chamber heated to a UNiform temperature within a Vacuum systerrz, it is possible to approach equiilibrium cod-tions r.~litl~irs the chamber. In this way; the sublimation and condensation proceed under near equilibrium co?zditions, and it was found that the properties of dePosited corrzpounds were similar to those of the source material. Oriented PbS films on sapphire have a roor?l- temperature unobility of 700 sq cm per v sec and a T-5/2 temperature dependence characteristic of bulk crrystnls. CdS layers on sapphive Izazse a resistivity ~uhich is corrlpamble to the resistivity of the souvce crystals over a range of four ordem of rrlagnitude. Irz contrast, Ihe resistivity of CdS films prepared by conventional evaporation depends largely upon the substrate terrzperat~ire and postheating treatrrletlt, vather than upon the properties of' the solirce rrraterial. In the case oj the CdS films the achievment of high carrier mobility required the cargful exclusion of cont~~~~ii~unts from the films. The steps taken to accomplish this included presublimation of the source material, performance of the deposition at a backg-m~ozd pressure less than 10-8 Torr, and a solvent extraction with liquid cadminum, similar to that described by Aven and woodbury. The deposition of ,films under near-equilibrium conditions is being op-plied to other classes oj COmpounds. II should he of 1:allce ,tor llle deposition of nny matevial that decomposes in the vapor state. THIN films of PbS and CdS have been deposited on insulating sapphire substrates by employing a sublimation technique using near-equilibrium conditions in ultrahigh vacuum. Oriented polycrystalline PbS and CdS films on sapphire have Hall mobilities approaching values characteristic of bulk crystals. In the case of CdS, special purification procedures were crucial in obtaining high-mobility films. Depositions were performed in a small quartz sublimation cell shown in Fig. 1 that contained the compound and the single-crystal sapphire substrate. The substrates were etched in tapered solutions of hot phosphoric acid, rinsed in deionized water, dried, and transferred to the cell under dry nitrogen. Graphite crucibles and substrates were used in experiments where it was necessary to provide an inert test vehicle for the analytical determination of impurities in the source crystals and deposited films. The crucibles and substrates were machined out of spectrographic-grade graphite having less than 1 ppm of impurities. A quartz mask was sometimes used to define a pattern which could be used for Hall and resistivity measurements. Close spacing between the compound and substrate was maintained to insure better transport of each component from the source material.

Jan 1, 1968

By I. V. Lunkin, E. B. Rakishev, B. R. Rakishev

In mining the method of statistical tests is used by solving of problems, exposing to influence of random factors. Such problems are: rational selection of equipment set; co-ordination in time of different processes; interaction between some processes and kinds of works. Usually it is considered that Monte Carlo method proves its value in the first place in that problems, which allow theoretical-probabilistic description. Analysis of numerical solution of mining-economic problems shows that the method of statistical tests may be used successfully by solving of determinate problems, which are solved usually analytically or by the methods of mathematical programming. We are talking about the problems of optimal use of resources, expedient placing of equipment, effective use of investments, rational planning of stripping and extracting works, groups of mining enterprises and about different variants of transport problem. In the report possibility of the method use is studied at an example of typical technical-economic problems solving. By solving of these problems the variant of the method with uniform distribution of random quantity had been applied and built-in random number generator of visual modelling system VisSim had been used. By algorithms elaboration it seems very perspective to use combination of the Monte Carlo method with traditional methods of numerical solving of the problems (methods of linear, nonlinear and dynamic programming and so on). Keywords: method of statistical tests, mining-technical problems, diapason of random number sample, efficiency function and its extremum.

Jan 1, 2003

By Harold Roast

THE object of this investigation was to compare the arsenical antimony-lead alloy with some of the regular bearing-metal alloys. With this end in view, the following tests were made: 1. Chemical analyses to show the composition. 2. Thermal analyses. 3. Macroscopic examination of fractures. 4. Microscopic examination. 5. Tensile tests. 6. Crushing tests. 7. Scleroscope tests. 8. Brinell tests, at temperatures from 80° to 400° F. Tests 3 to 8 were conducted on both sand-cast and chill-cast specimens. For the purposes of this paper the alloys have been numbered from 1 to 6; their composition is as follows: LEAD, ANTIMONY, TIN, COPPER, ARSENIC, NUMBER PER CENT. PER CENT. PER CENT. PER CENT. PER CENT. 1 82.64 12.95 4.40 0.01 none 2 27.54 9.94 59.87 2.65 none 3 77.65 20.75 none 0.13 1.47 4 82.95 16.85 none 0.20 none 5 83.78 15.35 none 0.05 0.82 6 0.15 7.87 84.13 7.85 none The analysis, in the case of the antimony, was made by solution in sulfuric acid and titrated with permanganate. For tin, the ferric-chloride method was used; for copper, the alkaline separations, and the thiocyanate methods; for arsenic, volatilization of arsenic and titration with iodine. The lead, with the exception of alloy 6, was taken by difference.

Jan 2, 1922

By Lawrence R. Artler

The North American Coal Corporation, its subsidiaries and other coal companies, have been mining the Pittsburgh #8 seam in Eastern Ohio for several decades. Underground mining by the "room and pillar" method, and more recently by longwall methods, have been practiced. This presentation deals with ground control problems and subsequent solutions to those problems for both mining methods. But first, let me briefly discuss some pertinent points about the geologic conditions of the coal seam near the southwest edge of the Pittsburgh Coal Basin. The Eastern Ohio region of the Pittsburgh Coal Basin is situated along the western edge of the unglaciated Allegheny Plateau. The local terrain is quite steep, with topographic relief of 430-500 feet being common. The coal thickness in the region ranges from 36"to 120", with the average being 60" in the areas being currently mined. Regional dip of the seam is toward the southeast in an amount of 10 to 40 feet per mile. A cross-section of the mineable seam generally consists of the main bench (60"), a rider coal (6"-12"), and a claystone parting (6"-12") for a total excavated height of 6-7 feet. Greater excavated height occurs where the fireclay floor is so soft and friable that movement of mechanical equipment breaks up the first 4-8 inches. Generally, the main bench and rider coal thin and become more variable toward the southwestern portion of the mining area. The rider coal also grades laterally into a coaly carbonaceous shale. In those areas where the roof coal can no longer be counted on to help support the immediate top, some of the main seam (6") is left to protect the overlying 8'-12' of mudstone/claystone strata. These strata are virtually non-bedded, highly slickensided units and are "hung in suspension" by roof bolts from a more competent limestone stratum above. These mudstone/claystone units are very susceptible to moisture and thus to the weathering cycles. The rider coal or 6" of the main bench is left in place to "seal" the mudstone/claystone units in Mains and Submains development. For many years, it was thought that the strength of the limestone member was detrimental in attempts to fully extract the seam by conventional means; however, longwall methods that have been more recently employed have broken the "myth" that the Redstone Limestone prevents full extraction of pillars.

Jan 1, 1984

By Kefton H. Teague

Olivine is a mineral containing a mixture of forsterite (Mg2SiO4) and fayalite (Fe2SiO4) in solid solution. The name olivine was first applied by Werner in 1790 (Hunter, 1941) because of the olive-green color of the mineral. Olivine is the principal component of the rock dunite, which itself is a member of the peridotite group of ultrabasic igneous rocks. European uses of the terms olivine and dunite are somewhat different than US usage. In commerce European usage defines dunite as containing 36 to 42% MgO, 36 to 39% SiO2, and loss on ignition of approximately 10%. The term olivine is used to designate a material containing approximately 85% forsterite, with a chemical composition of approximately 45 to 50% MgO, 40 to 43% Si02, 5 to 8% Fe2O3, and ignition loss of 1 to 2%. Uses The principal use of olivine is in various applications involving hot metal. Table I shows the best estimate available as to the amount of olivine consumed by various industries worldwide. In excess of 90% of world uses involve hot metal, with approximately 75% as a slag conditioner in the blast furnace production of pig iron. Approximately 15% of total olivine usage is as a special foundry sand in mold making for the brass, aluminum, magnesium, and manganese steel foundries (Schaller, 1957, 1958; Snyder, 1957; Anon., 1977). Olivine was first used as an industrial mineral in the early 1930s for a refractory material (Anon., 1970; Hunter, 1941). As a refractory raw material, olivine was first introduced in the United States as hand-cobbed, selected, shaped blocks of crude olivine. This use met with limited success. More recently, finely ground olivine blended with MgO and pressed into bricks, which are then fired, has found use in glass tank furnaces and open-hearth furnaces. Ramming or gunning mixes for basic furnace linings also utilize olivine. Olivine has been used in ladle linings with varied success. In Europe, substantial tonnages of olivine are utilized in refractory brick for night storage heaters (Anon., 1970). A limited amount of olivine has been used in the past as a fertilizer (magnesium source) and has been fused with rock phosphate to produce a magnesium phosphate as a plant food. The relatively high magnesia (MgO) content of olivine also attracted attention to it as a potential source of both magnesium compounds and as a source of metallic magnesium (Bengston, 1956; Hunter, 1941). The use of olivine as an additive in the blast furnace is relatively new, having been developed during the last decade. J.W. Currier (Private communication, 1978) describes the behavior of olivine in the blast furnace as follows: Olivine (Mg, Fe2, Si04) represents a unique lime-free source of magnesia and silica as a blast furnace charge component. Only recently has the magnesia-rich mineral been recognized as beneficial cleaner for blast furnace experiencing the problems associated with excessive alkali inputs and/or low coke stabilities. For some time it has been known that alkalis tend to recycle and accumulate in blast furnaces. In the high temperature region of volatilization the elemental alkalis formed attack the integrity of the graphite structure. This alkali attachment is enhanced when poor coke is used. Higher in the furnace stack volatile alkali cyanides condense and oxidize. This accumulation of alkalis tends to agglomerate the burden materials, producing scabs and scaffolds. These structures not only inhibit the downward movement of burden materials and the upward passage of wind, but also lead to erratic furnace performance

Jan 1, 1983

By M. C. Fuerstenau, A. M. Gaudin

A homogeneous suspension is viewed by X-rays. The radiation density seen, affords a measure of the extra absorption due to the solids contained. This radiation density, at a predetermined depth, varies with time. The chart of this relationship gives the desired determination. s it is frequently necessary to know the distribu-rt tion of particle sizes in various products used in industrial applications, a number of means have been devised for these determinations. Some of them include direct microscopic measurement, screening of product, extraction of samples from a settling slurry, air and liquid elutriation, adsorption of gases and liquids, and light absorption. The absorption of light as a means for particle size analysis has been known and employed for some time. X-ray absorption has not received the attention that light has enjoyed primarily because of the complex and costly instrumentation involved with X-rays. In 1954, Brown and Skrebowskil suggested the use of X-rays for this type of determination but did not supplement their suggestion with experiment. In 1958, the authors conducted size analysis experiments on suspensions of quartz with the Trans-viewer: an X-ray unit specifically adapted for sedimentation research, and Rossa conducted experiments in a similar manner in 1959 with a stable gamma emitter, AmZ4l, on suspensions of uranium oxide. To illustrate the applicability of X-ray absorption for analyzing particle size distributions, an essentially mono-energetic and well collimated X-ray beam was used as a source. The beam was made mono-energetic by placing a zirconium filter before the counting window together with feeding the pulses from the proportional counter into a reverter, a device capable of discriminating against pulses of various heights. The sketch in Fig. 1 shows the collimation arrangement in more detail. As shown, the X-ray beam was collimated by inserting a 3/8-in. ID pipe into one of the ports of the X-ray tube and further by two small steel plates with slits 3/32-in. wide and 1/2-in. long placed in front of the window of the Geiger-Mueller (G-M) tube. One of the plates was located 1/2 in. and the other 2 1/2 in. from the window of the counter; both plates were contained in an aluminum holder mounted on the box containing the G-M tube. This type and degree of collimation should eliminate any intensity due to scattered radiation; the transmitted intensity would then be solely a functior. of the absorption by the suspension at that level. Experimentally, homogeneous suspensions of finely ground quartz were prepared, Daxad (a sulfo-nated compound made from wood) was added as dis-persant, and the transmitted X-ray intensity measured as a function of time at a fixed depth in the suspension. In more detail, the experimental procedure involved the following: 1) measuring the transmitted X-ray intensity through the Daxad solution at a predetermined position or settling depth in the absence of solids, 2) placing a known amount of dry solids into the vessel and agitating thoroughly, 3) measuring the transmitted X-ray intensity at time zero (i.e., immediately upon cessation of stirring), and 4) measuring the transmitted X-ray intensity as a function of time (a 10-sec counting interval being chosen and counting being started 5 sec before the desired time). Since a linear relationship exists between percentage solid in a slurry and the logarithm of transmitted intensity for a homogeneous material, the cumu-

Jan 1, 1961

By J. G. Richardson, F. M. Perkins

Results and procedures are pre-cented covering a laboratory investigation of the effect of rate of water advance on the displacement of oil from clean water-wet sands. The experiments included water floods at atmospheric pressure with and without gas present over a range of flow rates from reservoir rates to rates ten thousand-fold higher. Water floods were also conducted at various rates at elevated pressure with no gas present. Other tests were made at elevated pressures by forming a free gas saturation by evolution of gas from solution in the oil before water flooding. Recovery of oil was found to be independent of the rate of water advance with or without gas present and independent of the pressure level of the water flood. A dimensionally-scaled model of a reservoir composed of a thick uniform sand was used to study the effect of rate on the tendency of water to underrun the oil because of the greater density of the water. Another model was used to study the effect of rate on the tendency of water to channel down the more permeable sand in a stratified reservoir composed of sands of diffierent per-meability in intimate contact. The effect of the presence of gas on the flooding conformance was studied with both models. The results obtained using these simple models provide a basis for predicting behavior in more complicated systems. INTRODUCTION In spite of the great amount of research on the flow of fluids in porous rocks, there still exists some disagreement as to the influence of the rate of water advance on the displacement of oil by water flooding. Various investigators have found that increasing the rate of water injection would decrease, increase, or have no effect on recovery of oil. One reason for this disagreement has been a lack of understanding of the effects of the capillary forces which influence the results obtained in the laboratory at low rates with short columns. Other causes of the disagreement have undoubtedly been inconstancy and uncertainty of the wetting properties of the porous media studied, inaccurate saturation determinations, and in some instances conclusions based on insufficient data. Capillary forces are involved in the displacement of oil by water in two ways. On the microscopic scale, the capillary forces control the dis- tribution of oil and water in the pore spaces of the sand. The magnitude of these forces is governed by the preference of the sand to be wet by water, the pore sizes and geometrical shapes, and the interfacial tension between the water and oil. On the macroscopic scale, differences in saturation at the flooding "front" when water displaces oil result in capillary pressure gradients. These gradients cause water to flow preferentially ahead of the front. In short laboratory columns at low rates, the front can span the entire column length. Also, at the outflow boundary the preference of sand to be wetted by water results in retention of water and a high water saturation in the region of the outflow face. This effect is commonly called the boundary effect.' The capillary pressure gradients which complicate the interpretation of flooding performance of short laboratory columns at low rates of water advance become negligibly small under certain conditions. The conditions where capillary pressure gradients are negligible are in long, homogeneous reservoir sands,' at high rates of water advance in short laboratory columns,3 and at any rate in laboratory columns as the residual oil saturation is approached. Thus, laboratory water floods, conducted

Jan 1, 1958

By A. Madrazo

The Standing-Katz method for predicting liquid densities of reservoir fluids has been tested using experimental data of 154 bottom-hole or recombined reservoir fluid samples. New pressure- and temperature-correction curves for the Standing-Katz type correlation are presented which improve the accuracy of prediction. INTRODUCTION The present study was undertaken to investigate the known methods of determining liquid densities and to select one of them which might yield a better correlation if additional data were employed. An appropriate correlation would incorporate the following characteristics: (1) ease of handling in the computations, (2) results within engineering accuracy and (3) data easily accessible. After careful investigation of the different methods, the Standing-Katz correlation1 appeared to have these characteristics. The Standing-Katz correlation for liquid densities of hydrocarbon systems is based upon limited data. The original work, which employs apparent densities for methane and ethane, was based on data of 15 saturated crude oils in equilibrium with natural gas. Therefore, a test of the correlation using additional experimental data would serve either to validate the Standing-Katz correlation or to form a basis for corrections if such were necessary. PROCEDURE AND GRAPHICAL SOLUTION The data of 154 bottom-hole or recombined reservoir fluid samples were employed to calculate the densities at 14.7 psia and 60°F by the method described in Table 1. Volume contributions for methane and ethane were assigned from the pseudo liquid density plot (Fig. I), but volume contributions for N2, CO2 and HzS were not considered. The densities computed at reference conditions of 14.7 psia and 60°F were then elevated to their respective temperatures and pressures by the use of the correction curves proposed by Standing.' The percentage differences between the experimental values and the calculated values were determined; these samples were grouped into temperature, pressure and density ranges to determine a possible trend. It appeared that, at temperatures above 160°F, the calculated density values were consistently larger than the experimental density values; however, no obvious trend was found for the density and pressure ranges. There is a relationship between the pressure-correction and temperature-correction curves. This relationship, embodied in the temperature-correction curve, can be expressed as follows. The experimental densities of 125 samples above their bubble points were known. From these isothermal data, it was possible to determine an experimental-density difference between two pressures; and (from Fig. 2*), a calculated density difference between the same two pressures was determined. The relative effect of temperature must be considered in the calculated-density values. The effect of temperature can be determined by entering Fig. 3* at the two densities in consideration and obtaining the change in density at constant temperature. This change, or delta density, must be added

By F. F. Craig

A series of both welter and gas puttern Hoods was made in the laboratory to study the oil recovery performances of .such operations. These tests were contlrrctt~tl on consolidated sandstone models, using oil. water, and gas. The model floods were scaled to reprotlrrce field performance under gas arid water five-spot injection. X-ray shadowgraphs permitted observation of the gross fluid movement within the models. A method was developed for applying the mobility ratio concept to water flooding and dispersed gas drives in a five-spot well pattern. The area1 sweep efficiency. tit breakthrough for dispersed gas drives is much higher than previorsly expected, Iying in the range of 50 to 100 per cent. A method is presented for predictitig the water-oil ratio performance of five-spot pattern water flood., in uniform sands. This method is verified experimentally for the cotidition of 120 free gas initially present and for va1ues of gas saturation normally encountered in fields following depletion operations. Prodrrction perfort?zut~cc for pattern gas injection is also predictable by this method. INTRODUCTION In field pattern hater flooding or dispersed gas injection operations, the displacing fluid (water or gas) is injected and oil is produced through wells which are, area-wise. small openings in a large container or rescrwir of oil. As a result, not all of the area between the injection and producing wells is necessarily contacted by the injected fluid by the time it first reaches the producing wells. The question arises in predicting oil recovery. as to what traction of the pattern area involved is contacted by either the injected water or gas due to the relative position of the injection and producing wells. This is the areal sweep efficiency. It is also desirable to know how well arrangement affects the oil production performance. A solution to this problem has been attempted by many means. Mathematical analysis¹,²,³, and electrolytic models', have been used to establish a breakthrough areal sweep efficiency of 73 per cent for a five-spot pattern in which the ability of the oil to flow ahead of the invading fluid is equal to the ability of the invading fluid to flow in the invaded zone. All of these studies simulate only one of many field conditions. Improved studies of areal sweep efficiency at breakthrough were made using the fluid mapper5, poten-tiometric models" and X-ray shadowgraph techniques. In these it was possible to study the effect of variations in mobility of the injected and displaced fluids, and so to cover a wide range of field conditions. The limitation of these studies is that, with these models, it was not possible to simulate the saturation gradient behind the flood front when oil is displaced by gas or water. In the most recent published technical paperS on the subject, a method was presented for predicting the oil recovery performance after breakthrough in a five-spot pattern water flood. The method involved correlations which were obtained experimentally using miscible fluids. One limitation of this work was that a saturation gradient, usually found in immiscible fluid displacement, was absent in these studies. Also the laboratory studies did not cover the situation of a water flood following oil recovery by depletion drive. as is the situation in most field water floods. The tests reported in this paper were made using oil. water, and gas, thus eliminating the simplifications of former studies. Also reported are laboratory studies on

Jan 1, 1956

By D. Duncanson, R. J. Davidson, C. G. S. Schmidt, G. A. Brown, J. D. Taylor, N. W. Hanf

The development of a cyanidation route for the treatment of gold-plant gravity concentrates is described. This work was carried out as a natural consequence of earlier improvements to the recovery of gold in the gravity sections of existing gold plants. Concern about the environmental aspects of the conventional amalgamation process was further motivation in the development of an alternative procedure. It was found that the partial pressure of oxygen in solution was the most critical reactionrate determining factor. The rate of gold dissolution was shown to be controlled by the reaction rate below approximately 25°C and by diffusion above that temperature. Thus, the efficiency of pulp agitation and oxygen partial pressure permitted a high degree of control over the rate of gold dissolution. The use of oxygen rather than air significantly increased the dissolution rate of both gold and silver. The solubilities of sodium, calcium, and potassium aurocyanide complexes under simulated reaction conditions were studied, and it was established that the values for the sodium and calcium complexes were limited, requiring the use of lower pulp densities and higher reaction temperatures for the treatment of very high-grade concentrates. The presence of excessive amounts of tramp iron in such concentrates of up to 25 per cent by mass was found to result in poor gold dissolution owing to the cementation of gold under certain reaction conditions. The maintenance of high oxygen partial pressures, together with high cyanide concentrations, high pH levels, and the presence of calcium in the system, all aided in passivating the tramp iron. Copper, gold, and iron were shown to be the main cyanide-consuming elements. Optimum gold dissolution was obtained in a closed bench-scale reactor incorporating a flotation-machine type of agitator for effective pulp agitation and oxygenation, the oxygen being recirculated. The reactor was designed to operate under a very small positive pressure. After reaction times of 2 to 6 hours at temperatures in the region of 30°C, both the gold and the silver dissolution averaged 99,S per cent. In the case of very high-grade concentrates, it was shown that gold could be floated in the same reactor by drawing off the flotation concentrate through a port in the reactor. A flotation recovery of 87,4 per cent of the gold in 3,9 per cent by mass was obtained. The recovery of osmiridium from cyanide-leach residues and the electrowinning of gold from the pregnant liquors were also considered as processing aspects in the treatment of gold-plant belt concentrates. Final table tailings with a gold concentration of 10to 12 gft were obtained. The results of the investigation strongly suggested that an alternative cyanidation route for the treatment of gold-plant concentrates was technically feasible, provided the system included effective agitation and oxygenation. In the case of lower-grade concentrates, cyanidation followed by the electrowinning of gold appears to be the simplest route, while, for high-grade concentrates, flotation and smelting of the concentrate followed by cyanidation of the flotation tailings are suggested. The use of oxygen rather than air for sparging the pulp would depend largely on the grade of material to be treated. A preliminary comparison of the costs related to the amalgamation and cyanidation processes for the recovery of gold from such concentrates indicated very similar capital and operating costs. It was concluded that other considerations, e.g. toxicity, safety, and lower labour requirements, were more important than such small cost differences. Furthermore, the 'opening' of the gold-plant gravity circuit, which would be made possible by a cyanidation route, would further reduce the operating costs because of the subsequent decrease in the tonnage to be treated.

Jan 1, 1978

By C. K. Eilerts, J. D. Ham

Laboratory research has been conducted to evaluate the characteristic effects of condensate saturation on the mobility of gas in typical reservoir rocks. A pump with two pistons provided phases in equilibrium at controlled flow rates and constant liquid-vapor volume ratios. Core samples were tested in a holder that permitted sealing steady-state phases in the pore spaces under flow test pressures for weighing with sufficient precision to give an accurate measure of the attained saturations. Parameters of the study were pressure, apparent velocity, flowing liquid-vapor volume ratio, fluid composition, core material and length-to-diameter ratio. Tests were conducted at 515 and 1,515 psia to determine the effect of pressure on the mobility-saturation relationship. Influence of the apparent velocities 0.30, 0.15 and 0.07 cm/sec and of five liquid-vapor volume ratios from 0.0001 to 0.01 was determined at 515 psia The principal fluid system was nitrogen and and separator liquid from a Gulf Coast condensate, but the effect of a condensate of different viscosity was also determined. The significance of a possible concentration of liquid near the outlet end of the test cores was investigated. Core materials included a consolidated sandstone and a low-permeability limestone. Relative mobility and liquid-vapor volume ratio relationships are concluded to be dependent on pressure, saturation and, to a lesser extent, on velocity. For each porous medium and fluid there is a minimum saturation essential to two-phase flow, and high velocities of flow have only limited effect on saturations in this range. INTRODUCTION It is now recognized that knowledge of the availability of a reservoir gas — the period that gas may be recovered from a reservoir at a given rate — is as important as the estimate of gas in place. When reservoir conditions are such that pressure decline owing to production will result in retrograde condensation, liquid saturation can increase in the structure around the production well in a way that may restrict flow capacity, and hence future availability. l Based on a numerical solution of transient radial flow of single-phase gas-condensate fluids, 2 a program for computing the accumulation of condensate in a reservoir and the effect of this condensate on deliverability has been developed. During this development a need evolved for data that described the influence of pressure, velocity of flow and condensed liquid on mobility as recovery progressed. This paper presents the results of experimental investigation to obtain insight into the mobility relationship at reservoir pressures of gas-condensate fluids. A core holder for flow tests at reservoir pressure was developed to weigh the core and its fluid contents under pressure to determine saturation. A specially constructed pump was used to drive a two-phase fluid through the core until a steady state prevailed. The core was used as a differential device, and properties measured were intensive rather than extensive. APPARATUS Fig. 1 shows a schematic representation of the major pieces of equipment used in the mobility determination. The weighable core holder is connected to a two-piston, constant-displacement pump. Attainment of steady-state flow is indicated by stability of the flow differential read from the high-pressure manometer. WEIGHABLE CORE HOLDER An important part of the data needed was the mobility-saturation relationship. This required that mobilities and saturations be measured at pressures, flow velocities and liquid-vapor volume ratios characteristic of condensate reservoirs.