Search Documents

By P. R. Levey, A. van Bennekom

The effects of nitrogen alloying on the corrosion properties of austenitic stainless steels were investigated by a combination of potentio-dynamic and surface analysis techniques. The results indicate that nitrogen undergoes the phenomenon of anodic segregation, affecting both general and localized corrosion resistance. Nitrogen alloying is found to be beneficial to general corrosion resistance in a de-aerated sulphuric acid solution, but to be detrimental in an aerated solution of sulphuric acid This phenomenon is explained in terms of an ammonium-ion polarization effect. Localized corrosion resistance is found to improve dramatically as a result of nitrogen alloying, the nitrogen improving the formation, maintenance, and stability of the passive film in environments that promote pitting various theories that have been proposed to account for these phenomena are discussed.

Jan 1, 1995

By Devan Naik, Matthew Stokes, Andy Nigro

This paper describes the surgical removal of a 24 ft dia. Slurry Shield TBM entombed beneath one of the country’s busiest commuter rail interlockings, the Harold Interlocking in Queens, NY, and the construction of the interface to a cut/cover tunnel which extended the mined tunnel section. A sophisticated SOE was built around the TBM to support active track loads within 8ft. of the excavation. Once the TBM head and guts were removed, a full round CIP lining was installed connecting the existing precast tunnel liner to the C/C tunnel under construction. All this construction was done on a narrow island of land without road access nestled between 7 mainline LIRR/Amtrak rail lines.

Jun 13, 2021

By Brett P. Spigarelli

To meet the growing need for CO2 capture and storage technology, Michigan Technological University is researching CO2 capture and storage using alkali solutions1. Without implementing emission controls, world energy emissions will rise from 29.7 billion t in 2007 to 42.4 billion t in 2035. The first objective of the project was to determine the optimal amount of alkali in solution for CO2 absorption. This was accomplished using theoretical equilibrium calculations and experimental absorption data for alkali solutions of 1, 2, 3, 4 and 5 weight %. As the % alkali in solution increased, so, too, did the ionic strength of the solution. Theoretical calculations took into account the effect increasing ionic strength will have on the solubility of gaseous CO2. The calculations assumed negligible formation of H2CO3, constant temperature and constant pressure. In the experimental setup, a 16% CO2 /balance air gas mixture was bubbled through an Erlenmeyer flask filled with an alkali solution. The gas exiting the flask was fed to a gas analyzer to record the % CO2 in the exhaust gas stream. The % CO2 absorbed was taken as the % CO2 in the exhaust gas minus the % CO2 in the feed. Theoretical calculations found that as the % alkali in solution increases, the solubility of CO2 decreases. This was verified by experimental data, which found that a 2% alkali solution, by weight, was the ideal solution for CO2 absorption. Current research is focused on using the 2% alkali solution for permanent storage of CO2 via mineral carbonation to produce a value-added product.

May 1, 2012

By B. R. Westphal

The Integral Fast Reactor (IFR) concept being developed by Argonne National Laboratory is based on the pyrometallurgical processing of spent nuclear metallic fuel with subsequent fabrication into new reactor fuel by an injection casting process. During fabrication, a dilute scrap stream containing uranium alloy fines and broken quartz (Vycor) molds is produced. Waste characterization of this stream, developed by using present operating data and chemical analysis, was used to evaluate different uranium recovery methods and possible process variations for the return of the recovered metal. Two methods, comminution with size separation and electrostatic separation, have been tested and can successfully recover over 94% of the metal. Recycling the recovered metal to the injection casting process was evaluated for the different economic and process impacts. The physical waste parameters and the important separation process variables are discussed relative to their effects on the viability of recycling the material. A discussion of the criteria that is being used to establish the acceptable operating limits is also presented.

Jan 1, 1992

By F. Elgersma

A high purity electrolysis solution is essential for hydrometallurgical zinc winning processes. For this reason ferric iron containing compounds such as jarosite are precipitated as iron and impurity collector during the calcine leaching. Jarosite thus forms a chemical waste and creates environmental problems. This research contributes to the development of a wet jarosite treatment process, where less contaminated jarosite is produced which can act as an iron source. The present work studies jarosite precipitation kinetics and the uptake of zinc cations in batch and continuous experiments. The distribution coefficient for zinc in continuous experiments is constant for a wide ratio of zinc over ferric ions in the solution. Addition of NH, + ions in batch experiments accelerates the conversion rate equivalent to the driving force increment. Addition of 50,2-ions above the stoichiometric ratio increases the conversion rate less then could be expected from the increase in the estimated driving force. Zinc ions tend to retard the conversion rate. An increasing reaction temperature increases the conversion rate. Below 75 ?C the conversion rate approximates zero.

Jan 1, 1990

By Steve Kral

Competition from foreign coal producers could displace as much as 9 Mt/a (10 million stpy) of US coal bound for power plants located near waterways. But, according to a Maryland-based coal consultant, it could be worse. Theoretically, about 52 Mt (57 million st) of domestic coal could be vulnerable to imports by 1990, said Forrest Hill, of Hill & Associates of Annapolis. Hill was speaking to about 150 coal industry executives and experts at the third annual Coal Marketing Strategies Conference in November. Most were at the Denver, CO conference to pick up tips on how to sell coal in an oversupplied market. Imports threaten domestic markets Of the 200 utilities studied by Hill and his staff, 119 are situated near major waterways, he said. However, most of those waterways are not equipped to handle coal from the shipping lanes. Good news for US coal producers. But don't breathe too easily. Foreign coal still poses a major threat to domestic markets, Hill continued. The strength of the US dollar is an obvious factor. But easy access to US utilities located on waterways combined with low rates for ocean vessels give foreign producers another edge. And foreign mines are typically low cost producers. For example, Hill said Colombia's huge Cerrejon mine can deliver coal to an Illinois power plant for $47.87/t ($43.39 per st). That compares to $52.85/t ($47.95 per st) from a Kentucky coal mine. Also, Colombian coal producers can generate a cash flow even if the coal sells for $27.50/t ($25 per st). The main competition US producers face from abroad, as Hill sees it, comes from Australia, Canada, Colombia, Poland, South Africa, and, perhaps, from Venezuela. Domestic producers, however, do have some things going for them. Most US coal buyers, Hill said, "are not wild about the idea of buying foreign coal." A 10% price advantage or pressure from public utility commissions would be needed to force some of them to buy foreign coal, he said. Some of the utilities contacted said they would not commit to more than one-third of their stockpiles to a foreign source. Another advantage for US producers is that they have room in their long-term contracts to cut prices and still maintain a profit, Hill said. Railroads, too, have high profit margins written into their rate structures. They are also aware of the import threat. Therefore, they may reduce their rates accordingly to keep their markets. Marketing's role The energy price shocks of 1972 and 1976 caused major adjustments in world economics. Coal was no exception. High oil prices caused many utilities to look at less expensive coal. As the market improved, coal prices began to respond, said R. Gale Daniel, of Anaconda Minerals Co. But clean air legislation and the strengthening dollar caused havoc in the coal markets, he said. The price of oil crashed, taking with it predictions of record coal use. The result is an oversupply of coal that has led to price cutting. Now, coal marketing must be recognized in its "true leadership role," Daniel said. Marketing people must know when to use spot sales to balance production objectives and maintain cost-effective-

Jan 1, 1986

By J. B. Rubinstein, V. J. Badenicov, S. T. Hall

A simulation technique of the flotation process and models for the solution of various problems are developed. A modular model of column flotation is constructed taking into account the kinetic relationship of the process and the hydrodynamic regime in the cell. Based on this, a technique of calculating the column parameters based on laboratory tests is developed (scaling-up), and applied for calcetest results is developed (scaling-up), and applied for calculating the design of commercial-scale columns.

Jan 1, 1996

By Julian Avery

IN its dual role of pig-iron smelter and gas producer, the blast furnace is a remarkably satisfactory and efficient apparatus. Many metallurgists and engineers have pointed out, however, that since the primary function of the blast furnace is to produce pig iron at the lowest possible cost, its function as a gas producer should be subordinated to this primary pur-pose. During the past 10 years or more, improvements in blast-furnace technique and economy have, in fact, been directed primarily to increasing efficiency in the use of the reducing power of the gases produced by com-bustion of coke at the tuyeres, to reduce iron ore within the furnace. The net over-all result is a decrease in the fuel value of the top gas per unit of volume, and per ton of pig iron, which is evidently more than offset in value by the corollary saving in coke and the possibility of increased furnace capacity, for otherwise there would be no point in making such improvements. The purpose of the present paper is to suggest that, while progress has been made in this direction, there is another approach to the problem of increasing the chemical and thermal efficiency of the blast furnace in its primary role as a pig-iron smelter, which appears to offer possibilities of improvement in over-all economy of a different order of magnitude than results thus far obtained by the use of other expedients. The present argument is based in large part upon the hypothesis that the effi-ciency and economics of pig-iron smelting are seriously and adversely affected by the phenomenon known as "solution loss," and that the problem of solution loss can be successfully attacked by increasing the over-all pressure; i.e., the "top pressure" under which the furnace is operated. It is indicated that pressure operation may also be expected to result in concomitant benefits, which may be summed up as generally improved operating conditions, together with a substantial saving in fuel and/or a substantial increase in furnace capacity.

Jan 1, 1938

By S. R. Reddy, R. G. Reddy

"The Margules equation is used for interpreting excess Gibbs energy of several ternary systems. In the present study activity coefficient of a dilute solute, 2, in a binary solvent 1-3 was derived. The derived expression is used to interpret logarithmic activity coefficient of oxygen and sulfur in several metallic systems. Self interaction parameter of the solute is derived from the partial function of solute using constant compositional path. An expression for logarithmic activity coefficient and self - interaction parameter of solute is also derived using Maclaurin infinite series. The derived equation is based on Maclaurin infinite series used successfully to deduce thermodynamics of self interaction of oxygen as a interstitial atom in two metallic systems. The predicted thermodynamic parameters values using Maclaurin infinite series and Margules equations, are in excellent agreement with the experimental data and also our predictions are far more accurate than the predictions made by other models.1 IntroductionIn most of the pyrometallurgical high temperatures processes, interactions of solutes such as oxygen, nitrogen and sulfur, with the solvent atoms are most important during refining processes. There are numerous theories are developed [1-25] to interpret the thermodynamics of solutes in multicomponent alloy systems. Which are mainly developed using statistical or Quasichemical equations.Wagner [4] developed one energy parameter ideal solvent model based on activity coefficient of solutes compositional dependency. He used one energy interaction term which is not able to account for interaction energy parameters for the same solute concentration at different solvent compositions and also it is ineffective model to predict for strong interacting systems."

Jan 1, 1996

By Julio C. Martinez, Jeffrey L. Rice, Hayden Weschler

This paper details the extensive underpinning required to hold up the 39th street Bridge while demolishing its massive support piers and building a 30ft deep Cut/ Cover RR tunnel beneath it. The underpinning/SOE support required the construction of 16 large hand dug pits 36ft deep that were reinforced and concrete filled. In addition, an extensive steel support system was tied into the bridge super structure. All of the underpinning/tunnel construction was done while a 110ton crane sat directly atop the heavily trafficked – 66 ft. wide bridge. The tunnel excavation, concrete lining and final bridge pier support work will also be presented. All work was done within 5ft of active mainline tracks and that required tight grouting behind all lagging to eliminate any track settlement.

Jun 13, 2021

By Yufeng Guo

Mineralogy and physico-chemical characteristics of a nickel hydrometallurgical residue and recovery of iron-bearing minerals by flocculation-magnetic separation were studied. The results show that the nickel residue is super-fine and fraction less than 0.045mm reaches 85.4%. Ferrous minerals are chiefly magnetite and ferruginous glass. Magnetite accounts for 31.7% and exists as free magnetite. Ferruginous glass is of multicomponent amorphous substances with low-iron grade but strong magnetism, and accounts for 39.9% of total iron minerals. Addition of flocculants increases granularity and magnetic force of fine iron-bearing particles and improves iron grade and recovery. The tests with flocculation separation show that a concentrate assaying 56.68% Fe with 81.72% recovery was obtained in a magnetic tube. A concentrate with 56.92% iron grade and 67.96% recovery was obtained by flocculation-magnetic separation with a magnetic cylinder.

Jan 1, 2006

By R. D. Carter

Methods are presented for calculating the performance of multiwell gas reservoirs. These methods account for two-dimensional, unsteady-state flow of a non-ideal gas through a heterogeneous formation. The performance can be obtained for gas reservoirs with known physical properties and configuration subjected to specified development and production schedules. These methods may prove helpful in optimizing the exploitation of gas reservoirs. The numerical solrrtion procedures given for this non-linear problem are extensions of known techniques for the linear diffusion equation. Two of these procedures are based on a new difference equation given by Saul'ev. Limitations and advantages of these procedures are discussed. An example solution is presented and is used to compare the calculation methods. INTRODUCTION Li planning the operation of a multiwell gas reservoir, it is desirable to predict its performance for each alternate development and producing schedule under consideration. This paper presents three numerical procedures that can be used to calculate such gas reservoir performance using a digital computer. These methods account for two-dimensional transient flow of a non-ideal gas within the reservoir. Extension of these methods to three-dimensional flow is possible. The paper is divided into three parts. The first describes the problem for which a solution is wanted and three numerical procedures that can be used to obtain solutions. The second discusses the information necessary to set up a problem. This part will be of greatest interest to the field engineer. The third gives data and results for an example problem. PROBLEM AND SOLUTION METHODS In the following development, a gas reservoir is regarded as a sealed, porous, permeable, heterogeneous body in which a single, non-ideal gas phase is flowing. Flow is permitted in the x- and y-horizontal directions, but is considered to be negligible in the vertical or z-direction. The reservoir can be tapped by one or more wells. Methods to be described provide a basis for calculating the complete performance of the reservoir, including rates and cumulative production from the wells, and pressure distribution and decline in the reservoir. If the isothermal flow of a non-ideal gas obeying Darcy's Law occurs in two dimensions in a region R, the governing equation in this region is:

Jan 1, 1967

By J. H. Brophy, A. I. Prill

The authors have previously investigated the solid-state activated sintering of tungsten powder with various Ni-Cu additions.' Log shrinkage vs log time plots showed changes in slope from 4 to x at intermediate times during the sintering process. This was attributed to a change in the rate-controlling mass-transport process from solution of tungsten into the tungsten-alloy interface to diffusion of tungsten in this interface. It was postulated that the melting of the activating layer should not affect this transport process. However, the superposition of rearrangement due to the presence of a liquid phase complicates the data analysis. It is the purpose of this note to apply the analysis of Prill, Hayden, and rohy' to account for "rearrangement shrinkage'? in liquid-phase sintering of the W-Ni-Cu system. This results in "solution-precipitation stage" shrinkage plots which were comparable to those obtained in solid-phase activated sintering of the same system. If one assumes total shrinkage to be the sum of rearrangement and solution precipitation, the effects can be isolated easily.2 This results in the general equation:

Jan 1, 1967

By S. G. Gibbs

A new method for predicting the behavior of sucker-rod pumping systems is presented. The pumping system is described by a flexible mathematical model which is solved by means of partial diflerence equations with the aid of computers. Polished rod and intermediate-depth dynamometer cards can be calculated for various bottom-hole pump conditions. The technique permits simulation of a wide variety of operating conditions, both normal and abnormal. The data generated with the new technique are useful in refining the criteria for design and operation of sucker-rod systms. INTRODUCTION Sucker-rod pumping systems are used in approximately 90 per cent of artificially lifted wells. In view of this wide application, it behooves the industry to have a fundamental understanding of the sucker-rod pumping process. Oddly enough, our understanding has been rather superficial. This is evidenced by the semi-empirical formulas which have been used as the basis for design and operation of sucker-rod installations. Thoueh- we have realized the limitations of our methods for many years, it has not been computationally feasible to use more refined techniques. With the advent and widespread use of digital computers, it is now possible to handle the mathematical problems associated with sucker-rod pumping. This paper summarizes a computer-oriented method which can provide greater insight into the sucker-rod pumping process. It is hoped that this technique, and techniques which may evolve from it, will prove to be the tool needed by industry to obtain the most efficient use of rod pumping equipment. THE MATHEMATICAL MODEL Prediction of sucker-rod system behavior involves the solution of a boundary value problem. Such a problem includes a differential equation and a set of boundary conditions. For the sucker-rod problem, the wave equation is used, together with boundary conditions which describe the initial stress and velocity of the sucker rods, the motion of the polished rod and the operation of the down-hole pump. Of these items, the wave equation, the polished rod motion condition and the down-hole pump conditions are of primary importance. Discussion of the mathematical model centers about these factors. ROD STRING SIMULATION WITH THE WAVE EQUATION The one-dimensional wave equation with viscous damp- is used in the sucker-rod boundary value problem to simulate the behavior of the rod string. This equation describes the longitudinal vibrations in a long slender rod and, hence, is ideal for the sucker-rod application. Its use incorporates into the mathematical model the phenomenon of force wave reflection, which is an important characteristic of real systems. The viscous damping effect postulated in Eq. 1 yields good solutions, even though nonviscous effects such as coulcomb friction and hysteresis loss in the rod material are present. Fortunately, the nonviscous effects are relatively small, so the viscous damping approximation used in the wave equation is adequate. The coefficient v is a dimensionless damping factor which is found in field measurements to vary over fairly narrow limits. For mathematical convenience the gravity term is omitted in Eq. 1. The effect of gravity on rod load and stretch can be treated separately, as will be noted later. Since Eq. 1 is linear, the legitimacy of this procedure is easy to demonstrate. POLlSHED ROD MOTION SIMULATION The motion of the polished rod is determined by the geometry of the surface pumping unit and the torque-speed characteristics of its prime mover. By determining the motion of the polished rod, we formulate an important boundary condition. From trigonometrical considerations it can be shown that the position of the polished rod vs crank angle 0 is given by (see Fig. 1) These equations are obtained from the general solution of the "four-bar" linkage problem and can be used to describe the kinematics of any modern beam pumping unit.' If prime mover speed variations are disregarded, the angular velocity of the crank is constant, and Eq. 2 can be used to predict the position of the polished rod vs time. However, the constant-speed condition leading to constant crank angular velocity is only approached in practice: hence, it is better to make provisions for prime mover speed variations in the mathematical model. The speed at which the prime mover runs is determined by its torque-speed characteristics and the torque imposed upon it. The torque that the prime mover "feels" is the net torque arising from the polished rod load and the opposing torque from the counterbalance effect. The

By Martin Brueggemann

The Tyrone copper solution extraction and electrowinning plant was the first such facility built by Phelps Dodge Mining Company in 1984. Over the next 20 years, the aqueous flow rate capacity of the plant has been expanded from the original design of 12,000 gallons per minute (gpm) to 34,000 gpm to meet production goals in the face of declining copper grades in the leach solutions. The ability to process higher aqueous flow rates through existing equipment comes at the expense of increased organic loss through entrainment to raffinate. These losses of organic (diluent and extraction reagents) can account for up to 10 percent of the plant?s total operating costs. With the recent dramatic price increase of petroleum-based products, these operating costs due to losses are sure to increase. This paper will discuss recent improvements at the Tyrone SXEW plant that have resulted in a 40 percent reduction of organic losses. These improvements include picket fence modifications, new fence materials, organic recovery systems, and operational practices within the solution extraction process.

Jan 1, 2006

By N Robb

This paper gives an account of the laboratory testing, plant testing and final inclusion of the two-stage sulphuric acid leaching process in the Milliken mill. Operational results for September, 1962, are presented, showing a uranium extraction of 95.5 per cent, with a saving of some 16 lbs. of 100 per cent H~S04 and some 9 lbs. of lime per ton milled. Methods for effecting further improvements in the process are indicated. HISTORY P RIOR to the incorporation of two-stage leaching, the process for the treatment of uranium ores at Milliken consisted of a single-stage sulphuric acid leach, followed by a solution recovery step involving washing in thickeners and two-stage filtration. The thickener overflow solution was subsequently concentrated and purified by ion exchange, and the uranium was recovered, by two-stage precipitation, as ammonium diuranate. Figure I illustrates this flowsheet. For satisfactory extraction of uranium from the. Milliken ore, a high residual acidity, of the order of 40 grams per litre of free acid in the discharge solution, must be

Jan 1, 1963

By Karl P. Norrena, Clayton V. Deutsch

Ore and waste cannot always be visually separated. The distinction between ore and waste may need to be made on the basis of blasthole sampling. Hand drawn dig limits or computer-generated contour lines do not account for uncertainty, economics or equipment. Geometric methods for interpreting grade information such as the polygonal or triangulation methods share the same limitations as contouring. Geostatistical techniques exist for the realistic modeling of grade variations and uncertainty. Decision analysis techniques exist for the binary classification of ore, and waste blocks in the presence of this uncertainty. Block-by-block classification is not enough; mining equipment cannot exercise free selection of blocks. There is a need for procedures to determine optimal dig limits that account for (1) the uncertainty in the grades, (2) the economics of risk-qualified decision-making, and (3) the ability of the mining equipment to dig to specific limits. This paper presents a procedure for optimal determination of dig limits that account for these constraints. Simulated annealing (SA) is used with modest computational requirements because the number of variables is relatively small. The solution of the optimization problem is dig limits that maximize profit under multiple constraints. The method is illustrated with different constraints and tested against hand drawn dig limits in a "Dig Limit Challenge," which illustrates the efficacy of the new method.

Jan 1, 2002

Alabama ranked 19th in the Nation in nonfuel mineral value1 in 1994, down from 18th in 1993, according to the U.S. Bureau of Mines. The estimated value for 1994 was $576 million, a 2.5% increase over that of 1993. This followed a 3.5% increase in 1993 over that of 1992. The State accounted for a little less than 2% of the U.S. total. Nonfuel mineral production in Alabama consisted entirely of industrial minerals; no metals were mined in the State. Bauxite materials mined in the State are a natural mixture of bauxitic clay and bauxite having very low iron oxide content and are primarily used to make refractory (high temperature resistant) products, rather than in the production of primary aluminum. In descending order of dollar value, the top four mineral commodities produced in Alabama were crushed stone, portland cement, lime, and construction sand and gravel. These commodities accounted for almost 88 % of the State's total non fuel mineral value, while crushed stone and portland cement together represented almost 65 % of the total. In estimated mineral production for 1994, Alabama remained first in common clays and first of only two States that produced bauxite; third in lime, kaolin clays, and fire clays; seventh in portland cement and salt; and was one of the top seven States that produce bentonite clays. The State dropped from third to fifth in masonry cement. Production of talc and pyrophyllite resumed in 1994. Compared with 1993, the value of crushed stone, lime, construction sand and gravel, common clays, kaolin clays, fire clays, bauxite, and talc and pyrophyllite increased. Decreases occurred in portland cement, masonry cement, industrial sand and gravel, and dimension stone.

Jan 1, 1995

By F. Castelli

A simplified non-linear method to predict the behaviour of a single pile and/or pile group under horizontal loads is presented in the paper. The evaluation of the non-linear lateral deflection is based on a procedure taking into account the decrease of the model stiffness with the increasing of the applied load. The solution derived firstly for the single pile, was extended to the case of a pile group introducing the p-multiplier (fm) concept proposed by Brown et al. (1988).

Jan 1, 2006

By L. S. Darken

In the study of reactions occurring in liquid iron, alone or in contact with a liquid oxide or slag phase, it has been found that the experimental data over a limited range of concentration can in some cases be represented satisfactorily by the simple equilibrium expression where (P) denotes the concentration of a product and (R) the concentration of a reactant in the reaction r1R1 + r2R2 + • • • D P lP1 + P 2P2 + • • • Some of the reactions for which it holds are listed in Table 1. For others, however, the simple equation apparently does not hold. This has been attributed to an improper method of expressing concentration (for instance, weight per cent instead of mol fraction); or it has been supposed that the solutions are not ideal in the sense that the activity of a component is not proportional to its true mol fraction. But it may be that the problem has been oversimplified by neglecting some molecular species actually present; that is, by considering only the ostensible simple components and thus leaving out of account possible compound formation. It is the purpose of the present paper to point out how, in a group of related cases, a reasonable consistent assumption relative to the presence of a compound makes it possible to express the experimental data satisfactorily by the simple equilibrium expression when this compound is taken into account, and to bring into harmony data referring to different reactions in liquid iron. There are several a priori reasons for believing that solutions in liquid iron should not deviate far from ideality, provided that the concentration of solute is not too great and is expressed in proper terms. The factors that commonly lead to nonideality in systems at ordinary temperature— as ionization or the occurrence of polar and nonpolar molecules—are presumably less effective in inetal and in slag systems at high temperature. Again, the type of equation commonly used to express the value of

Jan 1, 1940