Search Documents

By Richard Kastner, Emilie Vanoudheusden, Fabrice Emeriault, Jacques Robert

INTRODUCTION The subway line B of Toulouse (France) has been realized with three different tunnel boring machines (TBM) techniques: Contracts 2 and 5 are excavated with earth-pressure balanced TBM, Contract 4 with a slurry shield TBM, and Contract 3 with a compressed-air TBM. The first three machines are around 7.7 m in diameter, while the last one is 5.3 m. Moreover, a small part of the line (50 m) has been excavated by a conventional method. The tunnels run through the Toulouse molasses, composed of hard sandy clay with pockets and lenses of dense sand. Geotechnical investigations have shown that in these formations, K0 is greater than 1, around 1.8 at a depth of 25 m (Serratrice,2005) and that geotechnical characteristics are homogenous on the whole layout (? =22 kN/m3, Su = 300 kPa, c' = 30 kPa, F' = 32°). The water table is found between 2 and4 m below ground level. As geology, stratigraphy and tunnel cover (between 10 and 20 m) are almost identical, a comparison of movements induced by the excavation by each of the four excavation techniques is possible. This paper presents the soil mass movement measures in the case of the conventional excavation method and in the case of TBM sections. It shows how tunneling parameters may explain the different surface movements observed during excavation. For the sake of simplicity, only the results of Contract 2 (earth pressure balanced TBM)will be presented. MONITORING Monitoring for the Conventional Method Section For the conventional method section (Vanoudheusden et al. 2005) the mass soil movements are measured with two inclinometers and one multi-point extensometer borehole with automatic data acquisition (Figure 1). The monitoring devices include

Jan 1, 2007

By W. L. Connell, O&apos

The properties of some heavy liquids which can be used in sink-float separations are discussed with major emphasis being given to the halogenated hydrocarbons. Data are presented on density, viscosity, thermal characteristics and the effects of moisture and temperature on the corrosiveness of the liquids towards various materials of construction. The toxicity of these materials, the hazards involved in handling them, and the procedures for handling them safely are also discussed. True liquids have certain advantages over colloidal suspensions for sink-float separation of minerals which makes their use especially advantageous when close separations, fine particle sizes or water-soluble minerals are to be treated. For best separating results, the medium should have an easily controlled, uniform, stable density. Here, true liquids have the advantages of allowing closer control of density and of not requiring agitation to maintain a uniform den- sity in the equipment. Low viscosities are desired in a separating liquid so that rapid separations of fine material can be made. Many liquids have lower viscosities than the colloidal suspensions at operating gravities of 1.4 to 5.0. For economic reasons and to prevent contamination of the product, the separating medium must be easily and completely removed from the ore. Normally, true liquids must be more completely removed than the cheaper suspensions and thus cause more problems in this area. The fact that the medium should not react with the minerals, air, water or the common materials of construction limits the choice of liquids which can be used, but many are available which are sufficiently stable. A more serious objection to the use of true liquids is that many of them present a toxic hazard to operating personnel and users of the product. Most true liquids are toxic to some extent, but modem knowledge of toxicity allows us to recognize the hazards inherent in handling them and enables us to design around them. Three types of true liquids are available for this use: 1) Halogenated hydrocarbons cover the gravity range from 1.2 to 3.3. They are generally more volatile and less viscous than the other liquids.

Jan 1, 1963

By K. S. Liddell, L. A. Smith

"Kell is a hydrometallurgical treatment option for the recovery of platinum group metals (PGMs), gold, silver, and base metals from flotation concentrates to refined products on site. The process is cyanidefree, while eliminating emissions of sulphur dioxide, arsenic trioxide, and other toxic species often emitted by smelters and roasters. Kell has been tested on a range of concentrates, including PGMs (UG2, Merensky, Platreef, Great Dyke, Great Lakes, Lake Superior and others), refractory gold-silver, coppergold, and polymetallic concentrates. High extraction efficiencies (>95%) are achieved for value metals (Pt, Pd, Rh, Au, Ag, Ni, Cu, Co) and secondary metals (Sb, Zn, Pb, and others). Studies comparing Kell with smelter-refining show economic benefits: capex 18–33% of smelting; opex 51–66%; electricity consumption 13–46%; and environmental benefits: greenhouse gas emissions 57–61% of smelting, acidification 5–27%, human toxicity 37–62%, and freshwater ecotoxicity 43–55% of smelting. Synergies for Kell plants alongside smelter-refineries include utilization of recovered acid from sulphur abatement systems and excess capacity in precious metal refineries. Kell is unconstrained by concentrate grade and impurities, allowing the co-location of Kell plants for treatment of non-smeltable concentrates alongside existing smelters.Kell has been demonstrated in a nine-week integrated pilot campaign at 1:1000 scale, supporting a bankable feasibility study for a 110 000 t/a plant treating a UG2-Merensky concentrate at Pilanesberg Platinum Mine (PPM), owned by Sedibelo Platinum Ltd, which has along with South African Industrial Development Corporation (IDC), invested in Kell. Zimbabwean Mining Development Corporation (ZMDC) has signed a Memorandum of Agreement (MOA) with KellTech for a centralized PGM concentrate processing plant."

Jun 1, 2019

By Lucio Fabio Cassiano Nascimento, Luis Henrique Leme Louro, Sérgio Neves Monteiro, Jheison Lopes dos Santos, Fernanda Santos da Luz, Fábio Oliveira Braga, Rubens Lincoln Santana Blazutti Marçal, Hugo Concolato de Oliveira Freitas, Édio Pereira Lima Júnior

Epoxy matrix composites reinforced with up to 10, 20 and 30 vol% of continuous and aligned natural mallow fibers and 30 vol% of mallow and jute hybrid fabric were for the first time ballistic tested as personal armor against class III 7.62 mm FMJ ammunition. The ballistic efficiency of these composites was assessed by measuring the dissipated energy and residual velocity after the bullet perforation. The results were compared with that in similar tests of aramid fabric (Kevlar™) commonly used in vests for personal protections. Visual inspection and scanning electron microscopy analysis of impact-fractured samples revealed failure mechanisms associated with fiber pullout, rupture and layers delamination. When compared to Kevlar™, the mallow fiber and hybrid fabric composite displayed practically the same ballistic efficiency. However, there is a reduction in both weight and cost, which makes both, mallow fiber and hybrid fabric composites, a promising material for personal ballistic protection.

Mar 1, 2018

By J. Betzhold

Knowing more about an orebody makes it easier to exploit it profitably. Many orebodies are made up of different rock types, alteration zones or mineralogical ensembles: oxides versus sulphides or facies with different metallurgical properties for example. Being able to model the spatial layout of these different facies is vital to good mine planning and management. Kriging cannot be used to generate numerical models of orebodies with complex geometric patterns because it gives too smooth an image. Over-smoothing has the meaning of changing the natural selectivity. Conditional simulations are required to do this kind of model respecting the natural variability: honouring the natural selectivity, dilution and ore loss. Standard geostatistical simulations cannot duplicate many of the complex spatial relationships seen in the earth sciences, such as differently orientated facies, sets of conjugate veins or ore types where certain facies cannot touch. After a presentation of the case study, it will be shown why traditional methods for simulating indicators like the sequential indicator simulations, or the truncated gaussian method, cannot be used to simulate it. Plurigaussian simulations are then introduced and shown to be more powerful than the previous methods in their range of application. This is confirmed by the case study treated; a Chilean copper deposit, for which the plurigaussian simulations are seen to respect the different orientations of the individual facies as well as honouring the facies seen in drill holes, and respecting the proportion of each facies even if this varies in space (e.g. increases or decreases with depth). Key words: geostatistics, indicators, conditional simulation, plurigaussian method, copper variability.

Jan 1, 2000

By E. B. Kroeger

Spoil instability has been a problem at a coal mine in interior Alaska. Parameters such as original site topography, groundwater conditions, material properties, spoil-pile geometry, geology, permafrost, natural slope instability, changing weather conditions, and dense, near-surface vegetation have interacted to produce unstable slopes. Several failure modes have been identified including deep seated earth block slides, bimodal earth flows, and solifluction. Thawing of permafrost also created conditions where sliding of spoil along the interface separating the spoil and the natural ground surface occurred when the cohesion and the friction angle of that zone was reduced to zero and below 15?respectively.

Jan 1, 1992

By JOHN HOMER, KATHLEEN STABRYLA, JACOB L. CARR, JONATHAN K. HRICA, JENNICA L. BELLANCA

Given the recent focus on powered haulage incidents within the U.S. mining sector, an appraisal of collision avoidance/warning systems (CXSs) through the lens of the research literature is timely. This paper aims to evaluate the maturity of CXS technology through the application of a technology readiness assessment (TRA) to research literature identified by systematic search methods. Results indicate that much of the evidence for CXS performance is at lower levels of maturity: that is, components and prototypes tested in a laboratory and in relevant environments. Less evidence exists for CXS performance at higher levels of maturity — that is, systems evaluated within operational environments — despite the existence of commercial products in the marketplace. This lack of evidence at higher maturity levels within the scientific literature highlights the need for more peer-reviewed research to evaluate CXS technologies. Additionally, results of the review reveal that most of the literature relevant to CXS technologies is focused on vehicle-to-vehicle interactions, which contrasts with haul truck fatal accident statistics that indicate most are due to vehicle-to-environment interactions, such as traveling through a berm. Lastly, the relatively small number and segmented nature of relevant studies suggest there is a need for more incremental research that would better facilitate the improvement of CXS technologies. This progression could be achieved through continued long-term interest and support for CXS technology research.

Mar 1, 2023

By R. W. Drier

THE conductivity of copper wire is of prime importance to the electrical industry and consequently to the copper refiner and wire manufacturer. Annealed copper wire has a higher conductivity than hard-drawn wire, but, on the other hand, its tensile strength is lower. In an attempt to explain the reasons for these changes in property or at least to study the conditions existing in these two types of copper wire, the experiments described here were carried on in the Department of Metallurgy of the Michigan College of Mining and Technology. This is only a partial and preliminary report on some of the work done to date on a research program of which the object is an intensive study of copper. It is offered with the hope that, though it is not an exposition of the most rigorous of conclusions, the general trend of inferences which may be drawn will be of value and interest.

Jan 1, 1929

By M. F. Trice

PYROPHYLLITE is a hydrous aluminum silicate (A12Si4010(OH)2)1 that occurs in both the foliated and the massive forms. The foliated variety resembles talc in that it has a greasy feel, a pearly luster, perfect basal cleavage, and usually is white, although in some deposits apple green, gray, brown, russet, and nearly black specimens may be found. The massive deposits of pyrophyllite yield pearl gray to light tan aggregates, some of which are so friable that they may be crushed with the hands into a fine gritty powder. Frequently specimens of the massive variety are studded with crystals of radial structure. The mineral has a specific gravity of about 2.7 and a hardness of 1 on Mobs' scale.1 The chemical composition of commercial pyrophyllite reflects the mineralogy of the deposits, which, according to Stuckey,2 contain pyro-phyllite and quartz, together with chloritoid, sericite, and a few other minerals of negligible importance. The latter, he says, "are noticed in but small quantities to the extent they might occur as accessory constitu-ents of an igneous rock or as products of regional metamorphism or weathering. . . . Quartz is abundant everywhere except in the very best grades of pyrophyllite." Analyses of specimens from several deposits are listed in Table 1, showing that the silica content varies from 57 to 73 percent and the alumina from 22 to 33 percent. Oxides of iron and the alkaline metals are collectively present, with one exception, to an extent of about 1 to 1.5 per cent.

Jan 1, 1940

A subsurface study of the Maria Lode and associated hydrothermal alteration of andesites within the Karangahake epithermal gold-silver deposit defined the local evolutionary sequence in the once active geothermal system.   Some implications for mining of epithermal deposits arise as a result.

Jan 1, 1984

CONTENTS PAGE ANDERSON, ARVID E., and CAMERON, FRANK K.-Recovery of Copper by Leaching, Ohio Copper Co. of Utah. Discussed by Thomas B. Brighton, H. C. Goodrich, Arvid E. Anderson, Thos. P. Billings, Frank K. Cameron 2 BEESON, J. J.-Mining Districts and Their Relation to Structural Geology. Discussed by Charles Keyes, Chas. A. Porter 4 DOBBEL, CHAS. A.-Deep-hole Prospecting at the Chief Consolidated Mines. Discussed by G. W. Crane 10 CRANE, G. W.-Notes on the Geology of East Tintic. Discussed by G. W. Crane, H. E. Havernor, N. O. Lawton 11 SACKETT, B. L., BARDWELL, CARLOS, JACOBSON, SIMON, and JENSEN, N. H. Lead Smelting in Utah. Discussed by D. W. Jessup, B. L. Sackett, E. H. Laws 13 BARDWELL, E. S., and MILLER, Roy H.-Pulverized Coal as Fuel for Copper Refining Furnaces. Discussed by L. D. Anderson, E. S. Bardwell, C. P. Crawford 15 WIGTON, G. H.-The Chief Consolidated Volatilization Process and Mill. Discussed by Thomas Varley, S. G. Olmstead, V. O. Lawton, O. C. Ralston.... 16 JESSUP, D. W.-Evolution in the Preparation of Ores for Lead Blast Furnaces. Discussed by W. Spencer Reid, D. W. Jessup, Carlos Bardwell 19 ALLEN, H. P., and MADGE, WM. C.-Chloridizing Mill of the Standard Reduction Co. Discussed by Thomas Varley, H. R. Hanley, H. P. Allen, George H. Dern 20 TUCKER, E. L., and HEAD, R. E.-Effect of Cyanogen Compounds on Floatability of Pure Sulfide Minerals. Discussed by Blarney Stevens 24 Mix, B. E., and BARKER, L. M.-Method of Unloading Ores and Coarse-crushing Practice at Magna Plant of Utah Copper Co. Discussed by W. C. Madge,B. E. Mix 25 KEIGLEY, C. T.-The New Byproduct Coke Plant of the Columbia Steel Corporation. Discussed by W. M. Grant, C. T. Keigley, A. C. Feilder 25 JACKSON, P. W.-Blast Furnace Plant of the Columbia Steel Corporation. Discussed by W. R. Phibbs, H. M. Henton 26 OLDRIGHT, G. L., KEYES, H. E., and WARTMAN, F. S.-Production of Ferric Sulfate and Sulfuric Acid from Roaster Gas. Discussed by G. D. Van Arsdale William E. Greenawalt, G. L. Oldright 27 MAZANY, M. S.-Braden Copper Company Caletones Smelter. Discussed by A. B. Young, G. L. Oldright 36 HARRINGTON, D.-Safety Methods in Utah Coal Mines. Discussed by Edward K. Judd, Otto Herres, Benedict Shubart, A. C. Watts, D. Harrington 36

Jan 12, 1925

Fault detection and identification are major challenges in process engineering and manufacturing and the key component of abnormal event management systems. Timely detection, diagnosis and rectification of abnormal or faulty process conditions can lead to savings of billions of dollars in equipment damage and lost productivity, not to mention the prevention of injury and loss of human life associated with industrial accidents. A major contributing factor to current losses in industry is the reliance on human operators to interpret high-frequency samples from hundreds or thousands of variables simultaneously. As a result, the automation of fault detection and diagnosis is seen as crucial to the successful implementation of abnormal event management, the need for which is becoming all the more urgent given the increased complexity associated with modem industrial plants. In this paper, a methodology for process monitoring that uses support vector methods to extract nonlinear features from data is discussed and applied in the diagnostic monitoring of an industrial liquid-liquid extraction column.

Jan 1, 2005

By Arthur Zentner

THE PAST YEAR saw important developments in all the main branches of zinc metallurgy, which can only be douched on briefly here. Vertical Retort Smelting-The New Jersey Zinc Co. reports their operations to be about as last year when the number of vertical retorts at the Palmerton plant was increased from 16 to 28. The first unit of eight vertical retorts at Oker, Germany, to treat the Rammelsburg complex ore was completed early in the year. A second unit has been under construction and is probably ready to start operations about this time. Each unit is rated for 10,000 metric tons of zinc per year. A plant of 40,000 metric tons annual capacity is the goal. A reflux plant was also built to make high-grade zinc. The plant program is being -carried forward with government finan¬cial assistance, as was the case with the electrolytic zinc plant at Magdeburg. Government subsidies cover mining and 'smelting, and allow for depreciation and reasonable return on invested capital, according to U. S. Bureau of Mines reports.

Jan 1, 1938

By L. H. DeWald

During the examination of various commercial brands of copper wire bars, which had exhibited different degrees of adaptability for being drawn into fine gages of wire by the present-day high speed machine, it was found that each brand had a more or less characteristic crystal macrostructure. The extremes of these macrostructures are similar FIG. 1.-EFFECT OF METAL TEMPERATURE IN CASTING ON CRYSTAL MACROSTRUCTURE OF BAR. Reading from left to right, metal temperatures were 1166" C., 1149" C., 1132" C.. 1121" C., 1093" C. to the maximum variation shown in the photomacrographs reproduced in Fig. 1. As the various brands did not differ materially in chemical composition, it was concluded that the differences in structure were the result of variations in casting technique.

Jan 1, 1931

By S. Mathur

Polyacrylic acid (P AA) was evaluated as a selective flocculant for dolomite-apatite system. P AA of 4 million MW was found to flocculate both dolomite and apatite. However, their flocculation behavior was significantly different with 450,000 MW PAA which was the lowest molecular weight fraction capable of flocculation. In single mineral tests, at a dosage of 2kg/t 90% of dolomite and 35% of apatite flocculated. Selectivity was achieved in mixed mineral tests where apatite of 90% grade at 70% recovery level was obtained in the concentrate from a feed consisting of 80:20 mixture of apatite and dolomite. The dolomite rejection was about 75% which corresponds to 1% MgO in the concentrate.

Jan 1, 1995

By C. E. Dodson

Conventionally hydrometallurgical recovery processes from sulphide concentrates include roasting, leaching, precipitation, impurity removal and zinc electrowinning. The use of the novel (yet commercially proven in other mineral and metallurgical industries) TORBED process reactor for the flash roasting of sulphides will be proposed. The potential advantages in its application will be discussed including very fine particle processing capability, lower cost smaller roasters, waste minimization, improved leaching efficiency and overall process simplification.

Jan 1, 1999

By L. R. Nelson

A review is presented of the furnace cooling system design and operating developments since the initial furnace start-up in January 2001 of the Chambishi DC-arc furnace to produce ferrocobalt alloy. The furnace operating conditions present a number of challenges to the furnace designers and operators, in particular, to provide a sustainable lining that can withstand the highly corrosive siliceous slag (roughly 50% SiO2). This is exacerbated by the dual requirement of operating this slag in a relatively highly superheated state (?T ?400°C when tapped at 1550°C) to ensure that the ferroalloy can be tapped (estimated 1370°C alloy liquidus temperature) prior to atomization. The core design challenge occurs at the alloy-slag interface, where a single refractory type cannot simultaneously meet the dual requirement of both adequate alloy and slag corrosion compatibility. Progression by the fourth furnace campaign to involve a retrofit of the bath sidewall to HATCH high-intensity, water-cooled, copper Waffle coolers and tap blocks is described. This involves operation of the entire slag bath, the slag-alloy interface and a portion of the alloy within a more chemically compatible refractory/slag (and possibly at times even an alloy) freeze-lining. Due to the high furnace power density employed (up to 500 kW/m2 hearth area), coupled with the large slag superheat needed, the resulting imposed peak bath sidewall heat fluxes are substantial, especially in the alloy (typically averaging 170 kW/m2), and on occasion have exceeded 1000 kW/m2. The performance of the HATCH Copper Waffle coolers under such aggressive process pyrometallurgical conditions is described. Aspects of the design and especially operating strategies to effect sustained production at up to 38 MW power input are also discussed.

Jan 1, 2004

By Maurice Deul

For the first half of the 21st century, the United States will rely on the same mix of fuels it has for the past 50 years. Petroleum for the United States will cost more and availability will decline as developing nations modernize. Increased use of natural gas for electric power generation will result in stress on the gas supply. Coal will be the fuel of last resort. More than half the petroleum used is imported, about the same amount as used for transportation. Only coal can provide relief by fueling railroads through electrification while encouraging “piggy-back” trailer haulage, co-generation for manufacturing and expanded passenger service.

Jan 1, 2002

By Thomas Niehoff

"Oxyfuel combustion systems are state of the art for many melting operations. Airfuel systems have been stepwise modified to oxygen enrichment, oxygen lancing and oxyfuel. Every change of the melting process will have consequences with regards to emissions and energy usage. The uniqueness of many operations requires unique skills to resolve potential issues. This paper will give some examples of how airfuel systems can successfully be converted to oxyfuel.IntroductionOxyfuel technology – meaning the combustion of fossil fuels such as natural gas, oil or coal with technical oxygen instead of air for industrial melting or heating processes is widely used in many industries these days. Even though oxygen production, storage and handling has been state of the art for decades other opinions exist. Often oxyfuel is regarded with fear and potential hazards like: “Oxygen makes the process too hot.”, “Oxygen will melt away the refractory.”, Liquid oxygen is dangerous.”, “Oxygen will cause explosions.”, ……etc.Typically a more detailed discussion about a specific industrial process and how oxygen can be applied in a safe and economic way the seeming issues go away."

Jan 1, 2010

The Aberfoyle Tin Mine lies on a wide sloping bench about 2,000-2,500 ft. above sea level, at Rossarden, 14 miles north of Avoca, in north-eastern Tasmania. The quartz-cassiterite veins were discovered in 1916, but mining did not begin until 1926. Trenching revealed seven small tin-bearing veins within a width of 57 ft. of Palaeozoic slates and sandstones, and it was assumed that the mineralization extended beneath the adjacent cover of Permian strata, but the presence of the main vein system (the 26 Vein System) was not suspected until the Aberfoyle Fault was discovered late in 1928.The mine has now been developed on thirteen levels, to a depth of 1,350 ft. The lower limit of economic mineralization appears to lie at about the ll-level, which is 1,060 ft. vertically below the concealed outcrop of the main veins. Production of tin and tungsten concentrates began in 1932, and to date more than 550,000 tons of ore have been mined for a recovery of 8,856 tons of tin concentrates, and 3,056 tons of wolfram concentrates, valued at approximately £6,500,000.This paper reports part of an investigation undertaken by the Mineragraphic Investigations Section of C.S.I.R.O. to study the mineral composition of the ore in relation to the apparent failure of cassiterite and wolfram mineralization to extend below the present working limits of the mine, and was first issued as Mineragrapnic Report No. 639.GENERAL GEOLOGY:The deposit consists of a series of quartz veins in a northsouth trending sheeted zone, transecting folded slates and...

Jan 1, 1957