Search Documents

By Chuanyao Sun, Zhenguo Song, Aijun Ren

"Lead-Zinc sulfide ore containing carbon is one of typical refractory resource. Because organic carbon has natural floatability, it has a great negative influence on flotation of lead-zinc sulfide ores. It is difficult to obtain qualified lead concentrate by flotation using conventional reagent system. In order to reduce the influence of organic carbon on lead and zinc flotation, two alternatives, i.e., removal carbon by pre-flotation or adding carbon depressant in lead and zinc flotation, can be adopted. If the flowsheet of removal carbon by pre-flotation is adopted, the lead and zinc recovery which are lost in the carbon tailings is often higher. If conventional carbon depressants are used in lead and zinc flotation, it has a certain depression effect on lead minerals. In the paper, the ore grading 1.49% Pb, 5.73% Zn, and organic carbon 3.14% has been carried out by flotation tests. In the bulk flotation of carbon and lead minerals, Pb concentrate is only about grading 21.00% Pb. In the pre-flotation of organic carbon, it’s hard to remove most of carbon, and the loss of Pb and Zinc recovery is too much in carbon tailings. New carbon depressant BK547 and three conventional carbon depressants including sodium lignosulphonate, Fe-Cr-lignosulfonate, and dextrin, are used in comparative tests of Pb flotation, and results show that BK547 have a good depression on organic carbon, and have almost no effect on Pb flotation. Using BK547 as carbon depressant, cycle test in flowsheet of two-stage Pb and Zn selective flotation and coarse concentrate regrinding have been carried out, and results show that concentrates grading 62.51% Pb and 41.33% Zn are obtained at recoveries of 70.24% Zn and 83.58% Zn.INTRODUCTION Lead and zinc mineral resources are still the main source of lead and zinc metal. For lead-zinc sulphide ore, lead concentrate and zinc concentrate are obtained by flotation. Minerals separation by flotation is a complex process and is dependent, along with other factors, on the relative distribution of hydrophobic (e.g. collector, polysulfide, elemental sulfide) and hydrophilic (e.g. metal hydroxide) species between different particles of the same mineral phase and between mineral phases (Piantadosi & Smart, 2002; Boulton, Fornasiero & Ralston, 2003). Organic carbon has natural floatability and is often associated with lead-zinc sulphide ores. If the content of organic carbon in the ore is more, the flotation index will become worse. The main problem is that the concentrates has too low grade to be qualified grade products for sale. At the same time, the consumption of reagents is more than ordinary ores without organic carbon. In order to solve the influence of organic carbon on the flotation of lead and zinc and other sulphide ores, a lot of research works have been carried out."

Jan 1, 2018

By Jiang Diao, Yong Qiao, Xuan Liu, Tao Zhang, Bing Xie

The equilibrium experiments between the FeO-SiO2-MnO-TiO2-V2O3-Cr2O3-MgO slag system and solid pure iron were performed to investigate the vanadium and chromium distribution ratio under Ar atmosphere. The influence of w(FeO), w(V2O3) and w(Cr2O3) in slag on vanadium and chromium distribution ratios were studied at 1653 K. The experimental results were compared with calculated distribution ratios based on molecule and ions coexistence theory. Both of them showed that higher FeO content in slag would improve the distribution ratios of V and Cr between slag and hot metal. The distribution ratio of Cr or V increased with the increase of Cr2O3 or V2O3 content, respectively. To optimize the oxidation of V and Cr from hot metal, a high oxidizing slag and suitable content of Cr2O3 and V2O3 in the slag were recommended. The results provided reference for the further study on the extraction of V and Cr in VTi magnetite.

Jan 1, 2016

By S J. Henderson

Pumped co-disposal of coal processing waste was promoted in the 1990-2000s as a low-cost highperformance alternative to tailings dams. In particular it would avoid high up-front capital for rejects trucks and dam embankments, and would produce a combined waste deposit with better geotechnical properties than either coarse rejects or tailings. Overall, the promise was not delivered; in particular, upon discharge the waste segregated by size, and operators responded by moving the coarser waste to contain the finer waste. In consequence, not only did design analysis lag behind construction, but some of the initial expectations persisted with the result that analyses did not fully represent what was occurring on the ground. After more than twenty years inspecting, designing and tending Co-Disposal Areas (CDAs), it is apparent that they are essentially upstream constructed tailings dams with some more favourable aspects but also a few unique quirks. Although waste management technology has moved on somewhat, the high cost of changing CHPP waste circuits means that most mines with pumped codisposal will continue to discharge mixed waste slurry into CDAs. It is therefore worthwhile to share some lessons in the hope of promoting sounder design, operation and rehabilitation. These include: • Discharged waste does not form a homogeneous wholly competent deposit but instead comprises materials ranging from sandy gravel to silty clay with the distribution determined by movement of the discharge and decant structures; • CDAs circulate and contain a lot of water; • As a result of the first two points, some areas of the CDA comprise saturated fine waste that is no different from tailings and, like tailings, often behaves in an undrained manner; • Seepage is inevitable and desirable because strength improves as water is removed. However, stability is strongly impacted by pore pressures and in design these need to be rationally rather than optimistically considered; • As CDAs are built to about 40m or higher, strength-deformation characteristics of the foundation become more important; • Even if geomechanically stable, CDAs will need covers to prevent salts and acids from reaching the surface; and • Erosional stability of the cover material(s) will probably dictate maximum slopes for rehabilitation.

Jul 1, 2021

By D. A. Ainsworth

"The first known use of activated carbon dates back to the Ancient Egyptians who utilized its adsorbent properties for purifying oils and medicinal purposes. Centuries later, the early ocean going vessels stored drinking water in wooden barrels, the inside of which had been charred. (However, by modern definition the carbon used in these applications could not truly be described as activated.) By the early 19th century, both wood and bone charcoal was in large scale use for the decolorization and purification of cane sugar.However, it was not until the beginning of the First World War that the potential of activated carbon was really capitalized upon. The advent of gas warfare necessitated the development of suitable respiratory devices for personnel protection. Granular activated carbon was used to this end as, indeed, it still is today.By the late 1930's there was considerable industrial scale use of carbon for both gaseous and liquid phase application and new manufacturing processes had been developed to satisfy the needs of industry. During the 1939-1945 war, a further significant development took place - the production of more sophisticated chemically impregnated carbon for the removal of both war and nerve gases."

Jan 1, 1984

By A Mackay

As a result of the explosion in the 512 panel at the Moura No 2 mine in 1994 the role of the ventilation officer (VO) to submit sealing plans (on behalf of the operator/underground mine manager) has become one of the key duties of the VO of an underground coal mine in Australia. The intent of a sealing plan is to document the controls used to manage the build up of flammable concentrations of gases, and for these controls to be reviewed by the industry regulators. These sealing plans have brought a large amount of focus onto the sealing process and served the industry well. The legislation does not define sealing, or when it begins, but throughout the industry typically sealing plans are submitted 30 days prior to the last seal being constructed. This practice appears to have originated from the Moura 512 panel being a standing bord and pillar panel and where the explosive gas mixture could only occur after it was sealed. However, since the Moura disaster the industry has become dominated by goafing style longwall mining. Goafing panels differ from standing bord and pillar panels in that they typically have an unventilated goaf that can potentially contain an explosive mixture from start-up. This was recently highlighted by the explosion and fire on Longwall No 1 Tailgate at the Blakefield South Mine in 2011. The author ponders whether the industry should revisit sealing plans to focus on the core hazard and define that sealing begins when flammable concentrations of gases are created. Although defining when mine sealing begins is the key outcome of this paper, the main point is that VOs and industry regulators need to clearly understand what can occur in the atmosphere of underground coal mines. CITATION:Mackay, A, 2013. A case for change - Defining mine sealing and understanding flammable mixtures during sealing, in Proceedings The Australian Mine Ventilation Conference , pp 307-310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By M. S. Ellis, D. J. Nichols

In 1999, 1,100 million short tons of coal were produced in the United States, 38 percent from the Northern Rocky Mountains and Great Plains region. This coal has low ash content, and has sulfur content in compliance with Clean Air Act standards (U.S. Statutes at Large, 1990). The National Coal Resource Assessment for this region includes geologic, stratigraphic, palynologic, and geochemical studies and resource calculations for 18 major coal zones in the Powder River, Williston, Green River, Hanna, and Carbon Basins. Calculated resources are 660,000 million short tons. Results of the study are available in U.S. Geological Survey Professional Paper 1625-A (Fort Union Coal Assessment Team, 1999) and Open-File Report 99-376 (Flores and others, 1999) in CD-ROM format.

Jan 1, 2001

By Haipeng Li, Jacob Masliyah, Barun Gorain, Jian Huang, Qingxia Liu, Zhenghe Xu, AuTec Innovative Extractive Solutions Ltd.

"Froth flotation is widely used to selectively separate one or more minerals from an ore over a wide range of particle sizes with high efficiency. Bubble–particle attachment is one of the most critical steps in flotation. The objective of this project is to demonstrate the need for an innovative dual bubble generator to improve flotation efficiency. This dual bubble generator was designed to generate two different sizes (micron size and typical flotation size) bubbles. The micron size bubbles generated on the crevices of particle surfaces in venturi type of cavitation tubes enhanced the attachment of fine particles to the bubbles in conventional flotation systems. They also acted as a secondary collector, which has the potential to reduce operation cost and improve flotation recovery. The dual bubble generator was evaluated for a double refractory gold ore with 3g/t Au, 1.5 wt% TCM (total carbonaceous matter) and 0.7 wt% sulfides. The results were compared with those obtained using a commercial bubble generator. Compared with the commercial bubble generator, the dual bubble generator showed not only a higher gold recovery, but also an improved separation efficiency, demonstrating the potential of dual bubble generator in fine particle flotation.INTRODUCTIONFroth flotation has been widely used in mineral processing and waste water treatment. However, flotation has been proven inefficient for fine particle recovery although it becomes increasingly inevitable to process fine particles with the depletion of easy processing ores. The critical problem of fine particle flotation is the low attachment of fine particles to flotation size bubbles due to their low collision rate. Based on a commonly acceptable flotation model given by R =F*[Pc*Pa*(1-Pd)], the probability of bubble–particle collision (Pc), attachment (Pa) and particles detachment from air bubbles (Pd) collectively determines fine particle recovery (R) (Yoon and Luttrell, 1986). Since Pc = (3Dp/Db) where Dp and Db are diameters of particles and bubbles, respectively, bubble size and particle size impact the bubble-particle collision in opposite directions. It is evident that the probability of bubble–particle collision decreases with decreasing the size of particles, leading to a low recovery of fine particles. In this case, reducing the bubble size and/or increasing the apparent size of particles by fine particle aggregation are clear means to improve fine particle recovery."

Jan 1, 2016

By M Saghaeian, V Sheikhzadeh, R Hejazi

Mining dilution is one of the most important factors affecting the economy of mining projects. Instead of quantifying dilution in mining studies, it is common to assume a general dilution such as 5 per cent for massive deposits. Dilution increases the operating costs in the plant by increasing the tonnage of material to be milled. It prolongs the mine life by reducing plant’s effective capacity. It also reduces the feed grade. In most cases, lower feed grade means lower plant recovery. Dilution also increases the cut-off grade, which in turn reduces the overall ore utilisation of a mine. In this study has been investigated applying pre-concentration by dry magnetic separation for decreasing of dilution impact on reserve estimation and open pit design in low-grade iron ore mine. Based on the preliminary open pit design and assumption 3 per cent as dilution factor, the mineable ore in life-of-mine (measured + indicated) has been estimated with Fe = 25 per cent, SiO2 = 49.7 per cent. Based on the experimental test work on the ore, by dry low intensity magnetic separation of dry HPGR product grinding circuit, it is possible to remove diluted waste material and liberated gangue before concentrate plant, so that around 34 per cent rejected and Fe grade increase from 25 per cent to 33 per cent and by weight recovery 66 per cent. The results of the test work showed that this methodology could decrease largely the impact of dilution in the feed to the plant. It also slightly effect on the reducing of dilution factor impact for open pit design and optimisation and leads to increase the mineable tonnage in the low-grade magnetite iron ore mine.

Aug 24, 2022

By Luis Hoyos-Reyes, Jesus Gonzalez-Trejo, Adriana Cervantes-Clemente, Marco Gutierrez-Villegas, Manuel Palomar-Pardave, Cesar Real-Ramirez

Recent improvements on Peirce-Smith Converters (PSC) have combined numerical and physical simulations. However, most of the physical simulations have been carried out in cold-water models with only one tuyere. Several authors have proved that 2D numerical simulations do not reproduce the hydrodynamic behavior observed in physical simulations. On the other hand, most of the 3D numerical models have used a PSC thin slice with only one tuyere, but symmetric boundary conditions on the virtual walls have been imposed in order to reproduce the behavior of the whole converter. Therefore, there is no coincidence with the rigid walls of the physical models. The aim of this work is to quantify the effect of the virtual walls boundary conditions of a PSC thin slice and to determine the minimum number of tuyeres to characterize the fluid flow behavior of the entire converter.

Jan 1, 2009

By Manabu lshimaru

Solid-liquid interfaces as well as defect formation processes during crystallization of melted silicon (Si) have been examined by using molecular-dynamics (MD) simulations. The ordinary Langevin equation employing the Tersoff interatomic potential was used for the calculation of the atomic trajectories. A solid-melt interface has a tendency to form {]] I} microfacets during the crystal growth in the [001] direction, while it is essentially flat during the (Ill) crystallization. Because of the difference of the interfacial structures, the structures of grown-in defects and defect evolution depend strongly on the growth direction. We discuss defect structures and their formation processes within the context of our results as well as previous experimental observations.

Jan 1, 2001

By N. Manopulo, J. Maier, L. Tong, C. Becker, P. Hora

The contribution presents a new finite element approach in which the common updated Lagrangian formulation is replaced by a spatial flow formulation applying a special arbitrary Lagrangian-Eulerian for-mulation (ALE). The description separates spatially the process in a die inside zone and in a profile zone. For the description of the inside zone, where the filling process occurs, a special Euler time independent mesh is applied. By this formulation the mesh has to be generated only once, which simplifies the generation of spatially optimized meshes. For mapping of the material flow during the filling process the method uses a flow surface traction method as applied in casting simulations. A further strength of the new method is the computational efficiency which allows the modelling of extrusion process with the highest complexity with a response time of 12 hours, which is important for the industrial optimization process.

Jan 1, 2015

By V. A. Luganov

The processing of pyrite concentrates may be accomplished with a preliminary enrichment due to withdrawal of iron sulfides from initial concentrate. The withdrawal of iron sulfides is possible with the help of magnetic separation when the magnetic iron sulfides (pyrrhotites) separate from non-magnetic fraction?the sulfides of non-ferrous metals. The conversion of non-magnetic pyrite to magnetic pyrrhotites of adjusted structure occurs because of roasting with the withdrawal a part of sulfur. The resultant pyrrhotites are strong ferromagnetic with hexagonal structure. This paper contains results of studying magnetic properties of pyrrhotites, findings of the de-composition of initial pyrite with the consequence homogenizing of product and hardening of product of decomposition in liquid nitrogen. Define the type of pyrrhotites super lattice structure, was established that at increasing of sulfur contention the magnetic properties of pyrrhotites are change ? pyrrhotite begin evince the properties of antiferromagnetic material and magnetic susceptibility of material is interruptive changing from 0 to 1.7×10-3~1.9×10-3 SI units/g system. The paper contains results of technological researching of pyrrhotizing-magnetizing roasting of pyrite concentrates in different condition: in unoxidizing, with the decreasing contention of oxygen and in autogenous regime in air atmosphere. Established that the magnetic susceptibility of products depend of pyrite degree dissociation and achieve 2×10-3~3×10-3 SI units/g system at 40%~45% desulphurization. Defined the conditions of steady regime autogenous roasting, at resultant products possess coefficient of magnetization, and this can be used magnetic separation for separating ferromagnetic pyrrhotites from gangues and non-magnetic sulfides of non-ferrous metals. This technology of pyrrhotizing roasting is recommended for effecting in industrial condition. The initial materials and products of roasting subjected to chemical, thermogravimetric, Moss-bauer spectroscopy and X-ray analysis, defined the magnetic properties.

Jan 1, 2014

By Leo Gentile, David Selhorst

The $528 million Toledo Waterways Initiative (TWI) was implemented by the City of Toledo in 2002 and completed in August 2020. Toledo is one of many US cities required to implement a Long-Term Control Plan (LTCP) but one of few to have completed its plan. TWI consists of three storage and conveyance tunnels, four below grade storage basins ranging from 4 to 36 million gallons (MG), miles of sewer separation and interceptor improvements, green infrastructure and other appurtenant structures to dramatically reduce combined sewer overflows to the Maumee River, Ottawa River and Swan Creek. All three rivers flow into Lake Erie. The City’s 180-year history as a Midwest shipping, manufacturing and transportation hub provided design engineers and contractors no shortage of unknown underground challenges to complete the projects. The City will begin its 5-year Post-Construction Compliance Monitoring in 2021 to satisfy the final LTCP requirement. A program overview and experience from tunnel and underground basin construction in urban areas with buried active and legacy infrastructure will be discussed.

Jun 13, 2021

By Harry W. Campbell

A mineral survey by Bureau of Mines personnel identified no mineral resources or mineral occurrences with development potential at prospects in the Mecca Hills Wilderness Study Area (WSA). Bentonite occurrences are in Skeleton Canyon and Surprise Canyon. Sand and gravel occurrences are numerous in and near the WSA. Much of the Mecca Hills WSA was leased for oil and gas exploration in 1983. No current mining claims or other leases were found in the study area. The Skeleton Canyon Clay Mine yielded clay to seal irrigation canals, Clay to seal ponds was also mined from the Red Top Clay Mine west of the USA. A sand and gravel pit south of the study area (near Box Canyon Wash) supplied material for local construction projects. A commercial sand and gravel pit was operating in 1983 near the mouth of Thermal Canyon 4 miles west of the WSA.

Jan 1, 1984

Hydraulic backfill is generally retained in slopes using permeable barricades. Mitchell et a! (1975), Mitchell (1992) and Grice (1989) have shown that under normal drainage conditions, barricades experience low levels of loading. Cowling et a! (1988) have also shown that barricades are susceptible to piping failures if excess water has ponded on the upper backfill surface and if leakage of backfill from the barricades has occurred. During 1997, six hydraulic backfill barricades failed in four different Australian mines. Fortunately, in each case, the quantity of backfill slurry released was small, and no injuries to personnel nor damage occurred. Detailed investigation of two of the incidents showed that the primary cause of failure could be attributed to the delivery of excess quantities of transport water from the low-density slurry. For each of the incidents investigated there was evidence of the development of piping failures, which resulted in hydrostatic loading conditions on the barricades from the ponded water on the upper backfill surface. The circular failure surfaces in the barricades were characteristic of the application of point loading Conditions.

Jan 1, 1998

This paper comprises a description of on-stream analysis instrumentation, including sample handling, X-ray optics and data processing. It also includes a discussion of some typical applications of an on-stream analyzer as related to the mineral processing industry. Introduction T WO automatic X-ray spectrometers have been developed for the simultaneous analysis of as many as six elements in a given sample. These instruments, namely the On-Stream Analyzer and the new Vacuum Simultaneous Spectrometer, have been designed specifically for process control in industry where large numbers of static samples or a number of flowing sample streams must be analyzed continuously with both speed and accuracy. This paper is concerned particularly with the application of these instruments for the continuous analysis of dynamic samples. The Instruments The On-Stream Analyzer and the Vacuum Simultaneous Spectrometer are intended to serve industry by offering two basic approaches to the problem of continuous sampling of flowing sample streams. The On-stream Analyzer (Figure 1) is designed for the completely automatic and unattended analysis of flowing sample streams in a programmed cycle of operation.

Jan 1, 1965

By S. Isaac

The networks of interdependencies between elements in building projects, referred to as the project topology, are often complex and difficult for project teams to comprehend. It is hypothesized that a graphbased model of the project topology can be based on existing data in Building Information Models (BIM), facilitating the application of graph-theoretic algorithms to analyze this topology. The objective of this study is to propose an outline for the synthesis of BIM and graph theory. This synthesis is expected to contribute to the development of new tools for representing, managing and analyzing the design of building projects.

Aug 1, 2013

By J. D. Jones

The geographic occurrence of economic mineral deposits presents a variety of problems in modern tailings disposal operations. This paper presents case histories in several sectors of the mineral industry as well as the several stages of operations planning required for new designs, system expansion, reactivation of abandoned systems and upgrading to present environmental standards.

Jan 1, 1978

By P. Romm

The German Kupferschiefer (copper shale) mining history reaches back over 800 years with its last active mines being shut down in 1990. Increasing metal demands and potential thread of future supply shortages led to the initiation of new exploration programs including feasibility studies for the Spremberg deposit as well as Federal Ministry of Education and Research (BMBF) funded research investigations of Kupferschiefer Waste Dump treatment in the Mansfelder region. This article describes the sensor based sorting results of coarse Kupferschiefer via Near Infrared (NIR) Sorting, being conducted by the department of mineral processing (AMR) in Aachen, Germany. It provides information about the necessity of presorting of the different ore types prior to flotation and puts the NIR Sorting results into context with conventional Kupferschiefer processing. Keywords: NIR sorting, kupferschiefer, sensor based sorting, preconcentration

Sep 1, 2012

By V. van der Merwe, C. W. Siyasiya

"A petrochemical company experiences premature thermal fatigue failure of the casting moulds used in catalyst production. The aim of the project was to find an alternative alloy that would outperform the current low-alloy cast steel used for the moulds. Based on their thermo-fatigue properties, 3CR12 ferritic stainless steel and H11 tool steel were chosen for testing and comparison with the currently used BS3100 B7 cast steel. Samples of each material were subjected to temperature cycling in a Gleeble 1500TM thermo-mechanical processing simulator, followed by surface analyses. The main parameters derived from the test work were the total true strain, the hot strength of the materials, and the number of cycles to failure. Additionally, the coefficient of thermal expansion for each material was measured using a Bähr dilatometer. H11 tool steel yielded the best performance by way of having the fewest surface cracks, the lowest total true strain per cycle, the most cycles to failure, the highest hot strength, and the lowest coefficient of thermal expansion.IntroductionThe Catalyst Manufacturing Plant (CMP) is a dusty environment with temperatures higher than ambient. Molten mill scale (magnetite, Fe3O4) is tapped from the electric arc furnace into the casting moulds at temperatures close to 1600°C. After 10 seconds the magnetite is quenched with a water spray for 50 seconds to a minimum temperature of 400°C. Sometimes there is residual water in the pans from the cooling fog process (water sprays) in the empty mould. In a typical plant, the factory produces 40–44 batches a day containing between 150–300 moulds, depending on the time required for the specific batch (Buchholz, 2014). The typical batch in the CMP usually weighs about 6 t. The thickness of the tap, speed of the casting belt, and tilting angle all affect the number of moulds per batch.One of the main problems faced during the molten mill scale casting is the premature failure of the casting moulds. Cracks initiate on the surface of the mould, which is in contact with the hot catalyst, and propagate into the interior of the mould. Cracks are generally concentrated in the middle area of the mould where the catalyst makes first contact with the mould, and which experiences the highest temperature fluctuations. This suggests that the cracks are caused by thermal fatigue during the casting process."

Jan 1, 2016