Search Documents

By K. J. Shoop

Coal-fired power plants in the U. S. produce approximately 20 million metric tons of Hue-gas desulfurization sludge every year. The sludge mainly consists of calcium sulfite and calcium sulfate. This can be converted to synthetic gypsum, which in principle could be a marketable commodity. However, many Hue-gas scrubbers produce sludges that do not meet the quality requirements of the gypsum industry, and so their sludges must be landfilled as a waste. If a suitable method can be developed for removing certain objectionable impurities from the sludge, it will then be possible to market the material instead of landfilling it. A sludge from a natural-oxidation scrubber was characterized, and the main contaminant was found to be calcium carbonate from unreacted limestone. Based on the particle size and the characteristics of the material, froth flotation was considered as a method for purifying the material. Since no flotation studies have ever been carried out to separate calcium carbonate particles from calcium sulfite or calcium sulfate particles, it was first necessary to select a suitable collecting reagent. Based on Zeta-potential studies, the most suitable reagent was found to be an octadecylamine-octadecylguanidine complex. Results are presented for flotation of calcium carbonate from scrubber sludge using this reagent, in a reverse-flotation process. The best results were obtained when the sludge was first pre-cleaned using a water-only cyclone to remove unfloatable coarse limestone, followed by froth flotation to remove fine limestone.

Jan 1, 1998

By Bernard J. Steblay

Two instruments have been constructed that extend microseismic data collection and processing capability for Bureau of Mines research in rock burst, coal bounce and outburst, and roof fall monitoring. The first instrument is a 13-channel tape-triggering system. This system allows better utilization of instrumentation tape recorders by collecting data digitally, turning the tape on only when valid data are present, and increasing the dynamic range of the recorder by using digital data. A digital-to-analog converter is used to provide analog output of the recorded digital data. The instrument records a much larger time slice of transient events than do current commercial devices. The second instrument is a microseismic energy measurement device. This device uses recent developments In integrated circuits to overcome the dynamic range and accuracy limitations of previous instruments. The analog signal is converted to a digital one, and then high-speed multiplication techniques are used to square the amplitude value in real time and integrate it.

Jan 1, 1983

By W. M. Middleton

The exploiting of geothermal steam is a new endeavor in this country and is for that matter a very new science in the world. With the majority of steam wells in the world having been drilled during the last twelve years relatively little experience and knowledge has been gained that can guide us as compared to the techniques the oil and gas producers have developed for their use. We few technical personnel associated with the field find it a continuous challenge to understand and explain what effects or causes the various unusual phenomenon experienced. We have had unending discussions attempting to formulate pet theories which we can use as guides. We know, so the geologists tell us, that the source of the heat is from the hot magmatic core of the earth. Theory has it that the magma is cooling off and that hot gases are given off as this magma cools and shrinks. In volcanic' areas along fault lines where the magma reaches closer to the surface than in other areas, there is a higher concentration of gas evolution; consequently, geyser or geothermal areas are developed. As these hot gases rise toward the surface they encounter various minerals, including overlying bodies of water. It is into these underground lakes that our wells are penetrating. As the heat enters these lakes it spreads out by conduction, convection and water migration. We can strike this hot water over quite large areas in many of the geothermal fields. At present there is one anomaly to this in the United States as there is in Italy where our wells do not penetrate a hot water lake. This is at The Big Geysers in California. Here superheated steam is produced with a heat content, so high that it could not have been boiled off of a fresh water pool. This puzzled us until last year when a well was completed into a large body of brine in the Imperial Valley. This brine exists at close to 500°F and at a hydrostatic pressure sufficient to preclude any boiling. It is now believed by some of us that a similar pool of brine must exist below The Big Geysers area, from which the steam is emanating. If there is such a brine pool, it offers a plausible explanation of the high-heat content, for brine boils at a higher temperature than fresh water. I am now beginning to think that a similar brine pool may exist under all the geothermal basins for if it is under two of them, it is highly probable that it is under the others. The partial understanding of what we are drilling toward, and formulating a theory to explain its behavior helps guide us in our steam well drilling.

Jan 1, 1963

By Zhiyuan Shen, Dan Zhao

The abstract discusses the importance of reliable mine monitoring systems for preventing accidents. It focuses on diagnosing ventilation system failures caused by roadway faults that alter airflow resistance. The paper proposes using an improved Support Vector Machine (SVM) method to identify the fault location based on changes in air volume detected by wind speed sensors. The approach involves building a sensitivity 0-1 matrix and establishing a roadway fault scope library. The improved SVM method is tested on the Daming coal mine, demonstrating its effectiveness in diagnosing fault locations, reducing training time, and improving accuracy compared to traditional SVM.

Apr 5, 2022

Segregation roasting tests were carried out on Zaire cobalt oxide ores assaying about 2% Co and 3.5 to 6.5% Cu. The major parameters tested during the laboratory investigations were temperature, dosage and type of reducing agent, dosage and type of chloridizing agent, and particle size. Results showed that standard conditions suited to the segregation of copper ores, i.e. low temperature and low dosages of reducing and chloridizing agents, resulted in the segregation of copper only, while conditions suited to the segregation of lateritic nickel, i.e. higher temperature and increased dosages of reducing and chloridizing agents, led to a successful segregation of both copper and cobalt. Under the best conditions, 88% of the cobalt and 98% of the copper could be recovered in a concentrate assaying 32.5% Cu and 8.5% Co. Alternatives to process such a concentrate are briefly reviewed.

Jan 1, 1993

By W. G. Sandell, L. C. Bauerle, K. C. Dean

"INTRODUCTION As a part of the wartime activities of the Bureau of Mines, metallurgical services were extended to other Government agncies engaged in purchasing and stock-piling some of the more critical and strategic materials. At the request of Dr. Alan M. Bateman, special representative of the Metals Reserve Company, metallurgical studies were made on three samples of oxide tin ore from, the States of Zacatecas and Guanajuato, Mexico. The samples were submitted for testing by A. Porraz of the Financiera Miners, S. A., institution Financiera, Edificio Guardiola, Despachos 500-507, Mexico, D. F.The samples as received were marked Nos. 1, 2, and 3 and described as follows:Sample 1. - Origin: Mining camp ""El Naranjo,"" municipality of Sombrerete, State of Zacatecas, Mexico. This sample was partly concentrated by washing and as received was all minus 10-mesh in size.Sample 2. - Origin: Deposits in Sierra. Fria and Juan Cherey, municipality, of Jerez,State of Zacatecas, Mexico. This sample represented run of-mine ore.Sample 3. - Origin: Mine ""La Frontere, "" Ranch of San Pedro del loya, State of Guanajuato, Mexico. This run-of-mine sample was low in tin content but came from a highly mineralized tin field."

Jun 1, 1947

By A F. Cropp, D J. Bradshaw, W R. Goodall

Mineralogy and critically the texture of both the ore and gangue phases are of paramount importance in the flotation recovery of copper from porphyry ores. Mineralogy and texture will define the theoretical grade recovery curve for a feed ore. Actual grade-recovery falling below this may be due to texture and gangue influences, whilst desired grade-recovery above this line will not be possible unless the characteristics of the feed are altered.This review discusses examples of porphyry copper deposits where process mineralogy has been used to characterise these textural and gangue influences on recovery by flotation. More specifically, the influence exerted by grain size, liberation, association and elemental distribution is explored. The implications of these on overall plant philosophy and operation are highlighted, along with the subsequent potential impact on recovery.CITATION:Cropp, A F, Goodall, W R and Bradshaw, D J, 2013. The influence of textural variation and gangue mineralogy on recovery of copper by flotation from porphyry ore - a review, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 279-292 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By J. Lui

At its Copper Cliff Smelter, bulk nickel and copper concentrate is processed in two Inca flash furnaces and Peirce Smith converters to produce Bessemer matte containing 0.6%Fe. After slow cooling and Matte Separation, Bessemer matte is converted into three main products using magnetic separation and flotation technology: (1) a nickel containing chalcocite concentrate (MK); (2) two types of copper containing nickel sulfide (ME and MR); (3) metallics (MYN). MK is further processed in the Inca top blowing bottom stirring MK Reactor to produce semi-blister copper containing ~4%Ni and ~3±1 %S. The semi-blister copper is then purified in the multi-purpose vessels (MPV) to produce blister copper by reducing Ni, Fe and S content through oxidation. High melting point NiO is formed inside the MPVs. The accumulation of solid NiO and other oxides requires periodic cleaning by adding reductant and furnace matte, a unique process called "washout" at Inca. For many years, the reductant used for the "washout" process has been 15%Si Ferro-silicon. With increasing cost and limited suppliers for 15%FeSi, alternative reductants were pursued. This paper summarizes the development and commercialization of new alternative reductants for MPV "washout".

Jan 1, 2007

By H. G. Papacek

The Fabrica Mine of the Brazilian iron ore company Ferteco mines on an extremely inhomogenous ore deposit. A large amount of the crude ore consists of fines minus 100 micron which cannot be sold without further treatment because of its chemical and physical properties. In order to make full use of the mined crude ore an expansion program has been realized which incorporates among others a concentrator to produce classified blast furnace ore , sinter feed and pellet feed. The pellet feed is converted in a 2.5 million tons per year Lurgi Dravo plant into high grade pellets. The paper discusses the selection of the concentration process, the pelletizing process and describes the experiences with the operation plant during the startup and the first years of operation.

Jan 1, 1979

By R. A. Campbell

The electric smelting of five lowgrade Canadian manganese ores has been investigated at the Mines Branch, Department of Mines and Technical Surveys, Ottawa. Ferromanganese, silkomanganese, and spiegeleisen were produced 1by special smelting processes from these ores since the latter were too low grade to be treated by conventional smelting methods. In one case the results were considered to be sufficiently promising to justify the construction of a pilot plant, by the Company concerned, for the further development of the process.

Jan 1, 1956

By R. W. Kobler

The pelletizing process for low grade iron ores has undergone continual changes since its inception over twenty years ago. These changes have necessitated filtration equipment changes in order to produce a product suitable for balling. With modern techniques it is now possible to produce pellets of 68% Fe from ores containing as low as 26% Fe. Low grade ores require fine grinding to liberate impurities This shift to finer grinds over the years has necessitated major changes in the filtration steps. Techniques are now available for producing suitable product from ores with Blaines as high as 3600 cm2/gram. This has been made possible by the development of high performance filters. Recent developments have reduced maintenance costs and produced higher production reliability. The paper discusses iron concentrate filtration from its beginning to present day design. It will be shown that the dewatering step prior to balling has gone through four generations of filters. Particular emphasis is placed upon hydraulic studies which have allowed today's optimum designs.

Jan 1, 1978

Stillwater Mining Company has an extensive history with tunnel boring machines (TBM) at the Stillwater and East Boulder underground PGM mines in Montana. The first use of a TBM was a 4 m (13 ft) diameter main beam unit at the Stillwater mine starting in 1988, where 6.4 km (4 mi) of tunnels were driven parallel to the J-M Reef orebody on four different levels. TBM?s were central to the development of the East Boulder Mine as two 4.6 m (15 ft) TBM?s drove two 5,639 m (18,500 ft) parallel tunnels to access the J-M Reef; one of these units is still in service driving a 2,591 m (8,500 ft) access West of the East Boulder mine for the Graham Creek project. For the Blitz Project, a 5.5 m (18 ft) diameter main beam unit will be utilized to drive a 6,858 m (22,500 ft) ventilation and rail haulage level East of the Stillwater mine. TBM?s have been preferred method for developing new mines and sections of the J-M reef as the geometry and geology of the Stillwater Complex allow for faster development compared to conventional methods.

Jan 1, 2012

By Ihsan Berk Tulu, Mustafa Can Suner

The synthetic rock mass (SRM) approach and discrete fracture network (DFN) model, generated from the field surveys, are novel methodologies to study fracture rock mass behavior. In this paper, SRM and DFN methodologies were used to understand the influence of natural fractures on the mechanical response and failure mechanisms of stone mine pillars. First, a multi-stage up-scaling procedure with the homogenization process is established. Later, a stochastic sampling process on the SRM model to have further insight on the stone mine pillar mechanics is performed. Two-dimensional Universal Distinct Element Code (UDEC) is utilized to represent intact rock with the Voronoi-Trigon discretized blocks and to capture fractured rock mass behavior. The laboratory-size limestone mine rock specimens are systematically up-scaled to the average width of the field-size stone mine pillars. Then, the DFN model, generated from field data, is sampled to construct the SRM of the field-size pillars. By doing so, the effect of discrete discontinuities on pillar stability is studied by assessing the pillar strengths and failure mechanisms in various width-to-height ratios.

Jul 8, 2022

By Mario A. Terceros Herrera, Mario Terceros Arce, Antonio Marinucci

A Smart Cell is a closed-type tip post-grouting device that is attached to the bottom of the steel reinforcement cage of a drilled shaft and is used to enhance performance and to reduce uncertainty thereof. Control of the grout is maintained within the device during injection and a uniform stress is imparted across entire base area simultaneously, inducing a pre-mobilization load into the shaft as well as the soil. This paper describes the construction and tip post-grouting of drilled shafts from two bridge projects in the Santa Cruz, Bolivia region along the Paraí River. During the grouting process at each project site, there were noticeable differences in the grouting pressures achieved and responses observed, even within short distances between shafts. For this project, the greater benefit of using the Smart Cells was the reduction of risk and uncertainty of performance due to the highly variable soil conditions. Ultimately, since the response of each shaft was observed during grouting and because a “minimum” value of shaft resistance (i.e., pre-mobilization of load) was measured, there is a greater reliability with the anticipated performance of the shafts when axial loading is eventually applied.

By Richard D. Graves

Pitch from low-temperature carbonization of bituminous coal was hydrogenated at cracking conditions in a continuous bench-scale unit to produce low-molecular-weight oils and tar acids. The pitch contained 15.6 pct benzene-insoluble material, 4.0 pct hexane-soluble oil, and 80.4 pct asphaltene by weight. At 475° C, 7,500 psig, and 1.5 hours residence time, hydrogenation products, based on the weight of pitch, were about 36 pct oil boiling below 325° C, 24 pct hexane-soluble heavy oil, 17 pct asphaltene, 1 pct benzene insolubles, and 12 pct hydrocarbon gases. The yield of tar acids boiling below 250° C was 4.3 pct, and the yields of C6 to C8 paraffins, naphthenes, and aromatics were each less than 1.0 pct. The yield of tar acids was within the range of yields obtained by hydrogenation or high-temperature carbonization of bituminous coal (2 to 5 wt pct). Yields of oil boiling below 325° C increased with increased residence time or temperature. There was little or no effect of residence time on yields of alkali- soluble material which contained tar acids. Yields of hydro-carbon gases increased markedly with an increase in temperature from 475° to 500° C. Lowering the hydrogen pressure to 4,500 psig resulted in yields similar to those obtained at 7,500 psig.

Jan 1, 1962

By S. Serranti

A fast, reliable, and low cost characterization of ore minerals products, as they result from different processing actions, represents one of the most challenging targets in the mineral processing sector. Today different techniques are available according to different sampling strategies and analytical principles. In this paper, the possibilities offered by the adoption of hyperspectral imaging based sensing units working both at micro- and macro-scale are presented and discussed. According to the different phases and stages of ore minerals and products characterization, and starting from the analyses of the detected hyperspectral firms, it is thus possible to derive useful information about mineral flow stream properties and their physical-chemical attributes. This last aspect can be utilized to define innovative process mineralogy strategies and to implement on-line procedures at processing level. The present study discusses the effects related to the adoption of different hardware configurations, the utilization of different logics to perform the analysis and the selection of different algorithms according to the different characterization, inspection, and quality control actions to apply. Keywords: process mineralogy, hyperspectral imaging, NIR spectroscopy, surface mapping, textural analysis, quality control

Sep 1, 2012

By Dean Brox

Tunnel boring machines (TBMs) have been used for the construction of various tunnels for mining projects for the purpose of access, conveyance of ore and waste, drainage, exploration, water supply and water diversion. Several mining projects have seen the successful and economic beneficial use of TBMs, and there is an increasing awareness of the benefits of TBMs for mining projects. Key technical considerations for the use of TBMs for the construction of tunnels for mining projects include geological issues (rock type, rock alteration, rock strength, rock abrasivity, durability, ground water inflows), depth of cover and the potential for overstressing/rockbursts, site access and terrain, portal locations, TBM constraints, minimum tunnel size, tunnel support requirements, contractor and labor experience, and project schedule demands. TBMs offer key project schedule benefits with high rates of progress, which is a unique economic advantage recognized for mining projects where timing is of the essence in order to advance mining development and achieve early startup for operations. A thorough evaluation of the anticipated ground conditions should be performed as part of the decision to adopt a TBM for a mining project. Minimum specifications for TBMs are necessary in order to prevent the incorrect type of TBM from being used. Appropriate geotechnical investigations are necessary in order to provide key information on the anticipated subsurface conditions for careful planning and design of the proposed tunnel alignment. The overall site and geological conditions associated with some projects may suggest that it is not appropriate to use TBMs for some mining projects due to a perceived higher risk.

Jan 1, 2013

By Wm. D. Jr. Sheldon

THIS paper presents practical data to aid in the selection of a mine ventilating fan, and outlines considerations to be made to ensure satisfactory operation and optimum efficiency of the fan. Much has been published on the general subject of mine ventilation, but the writer has found few specific data on factors and considerations which govern the selection of a fan-data which should be available to the operator if his fan is to give satisfactory service within the range of the high-efficiency portion of its performance curve and deliver the specified air capacity when operating against the anticipated range of resistance of the mine. The total quantity of fresh air furnished by the ventilation system must be adequate to provide, and to ensure at all times, safe and healthful working conditions in the mine. It is assumed that the mine operator is able to determine the air quantities required for the various parts of the mine.

Jan 1, 1941

By John P. Turner, Benjamin J. Turner

"This report describes a research project for evaluating the applicability of the widely accepted 80 percent criterion for elongation of ground anchors to anchors with unbonded lengths exceeding 100 feet. This issue is driven by several recent projects involving ground anchors for landslide stabilization in which a significant percentage of the anchors did not meet the criterion that requires measured elongation during proof load testing of at least 80 percent of the theoretical elastic elongation. The projects involved anchor unbonded lengths in the range of 85 to 220 feet, which is outside the range traditionally used in practice, although anchors of this length are being used more frequently for landslide stabilization. The principal objective of this research is to address whether the widely accepted criterion of 80 percent elongation is applicable for such applications, and whether other factors affect the ability of anchors to meet the criterion.Analytical methods for predicting transfer of load along the length of steel strand due to friction loss are used routinely in the prestressed concrete industry. These analytical expressions provide a rational framework for quantifying changes in load due to friction along the length of a ground anchor in terms of a ‘wobble coefficient’ (K) as defined in Aalami (2004). Values of the wobble coefficient for ground anchors can only be determined by back-calculating from load tests, i.e., fit the value of K to the appropriate analytical expression based on the known test load and measured percent elongation. The analytical basis is first developed and shown to provide a tool for evaluating results of anchor load tests to determine the magnitude of expected elongation as a function of unbonded length. Next, a database of anchor load tests is used to back-calculate values of K for anchors with unbonded lengths in the range typically used in geotechnical applications (< 100 feet). These values of K are then used to calculate expected friction loss for anchors with high unbonded lengths (100 to 250 feet) to evaluate whether the 80 percent criterion is reasonable."

Jan 1, 2017

By Charles F. Park

Mining in the Pacific Coastal Region has passed through three stages of development. First came the gold rush days, a period when gold and silver were the objects of intensive search. Second was the development of the high-grade base-metal deposits and of the smaller and more refractory precious metal deposits. And third was the modern period that covers the discovery and development of the rarer metals, of large low-grade deposits, and of the industrial and nonmetallic minerals. Brief discussions of the salient geologic features of the region and of a few of the better known mineral deposits are given. The regional geology is favorable for continued exploration and discovery of new deposits and districts.

Jan 1, 1968