Search Documents

By J. L. Thompson

The U.S. Bureau of Mines conducted a water-jet-studies program using a single-bit, in-seam test unit to determine effects of a moderately high-pressure (up to 10,000 psi) water-jet-assisted cutting system on rock weakening. The in-seam test unit was used to obtain cutting force data in tangential, normal, and side force directions. Conical continuous miner and radial longwall miner bits were used to penetrate test samples of coalcrete, Berea sandstone, and Indiana limestone with unconfined compressive strengths of 4,600, 8,000 and 10,000 psi, respectively. Depth of cut in the coalcrete tests was 1 in, with 2-in cut spacing (2:1 ratio). Because of cutting equipment and instrumentation limitations, the Berea sandstone and Indiana lime-stone were cut using a 0.5-in depth of cut and 2-in spacing (4;1 ratio). Bit velocity was maintained at 25 ft/min for both bits. Each specimen and bit type was tested using 0.3-, 0.6-, 0.8-, and 1.0-mm-diam nozzles and water-jet pressures of 2,500, 5,000, 7,500, and 10,000 psig. Water-jet-assisted cutting decreased average resultant conical and radiallongwall bit cutting forces 6.4 and 8.4 pct in coalcrete, 5.5 and 1.4 pct in Berea sandstone, and 2.0 and 5.5 pct in Indiana limestone. Slight reductions of power requirements resulting from water-jet assist were ascertained during these experiments.

Jan 1, 1989

By M. E. Tyrrell

Lightweight basic refractories suitable for use in some sections of the all-basic furnace were developed. Potential advantages of such refractories are lower weight, improved resistance to thermal shock, and less tendency to spall off the working face. Plant trials in positions not subject to heavy loading or severe erosion seem warranted. Forsterite (2MgO.SiO2), stabilized dolomite (2Ca0?SiO2 + MgO), and chrome-spinel [(Fe,Mg)0?(Cr,Al) 031 refractories were fabricated using bubbles as the principal component in the brick mixtures. Bubbles were blown from melts of the basic raw materials as they were tapped from a conducting-hearth arc-resistance furnace. The bubbles were graded, bonded with synthetic Forsterite plus mineralizers, dry-pressed, and fired to temperatures of 1,600° C. or over in a gas-fired kiln. Refractory properties of the bubble brick were compared with those of insulating refractories made by burning combustibles out or dense brick mixtures. Lightweight refractories fabricated of bubbles were one-third lighter in weight than dense bricks of like materials. Their mechanical strength was satisfactory, and their resistance to thermal shock was excellent. In tolerance to open-hearth slag and in resistance to thermal shock, the chrome-spinel bubble bricks wore the best of the refractories tested. Basic refractories of the insulating type were about 40 percent lighter in weight than dense commercial refractories, but they were mechanically weak and not suitable for superduty service.

Jan 1, 1962

By Wainer da Silveira e Silva, Marco Antonio Teixeira, Robisom Damasceno Calado, Carlos Alberto Chaves, Tone Takayama Filho

A preocupação com o adequado tratamento de resíduos industriais surgiu com o conceito de desenvolvimento sustentável criado pelo Clube de Roma e contribuiu para o uso racional dos recursos naturais ao longo dos últimos 50 anos. A preocupação com a produção responsável e uso judicioso de recursos naturais priorizou a reciclagem de materiais na agenda das empresas, tornando-se numa atividade de alta relevância, vital para a sustentabilidade econômica e ambiental. Este trabalho aborda os aspectos técnicos, econômicos e ambientais da reciclagem de resíduos contendo zinco através do estudo de caso de reciclagem de resíduos gerados no processo de fabricação de aço em Forno Elétrico, denominado pó de Aciaria Elétrica (PAE). A indústria ainda está em busca de tecnologias para redução da geração e reciclagem desse resíduo. A relevância do estudo está na utilização da Análise Hierárquica de Processo (AHP) para avaliação e seleção da melhor alternativa, entre várias, para tratamento e reciclagem do PAE. Como resultado, demonstrou-se a eficácia do uso da metodologia no empreendimento de reciclagem de resíduos contendo zinco implantado pela Votorantim, em Juiz de Fora, Minas Gerais.

Nov 12, 2019

By Fredrick M. Ryan

Present indications are that in about 2-3 years phosphor tags will be required in commercial explosives. A permissible 254 run ultraviolet lamp assembly has been developed to permit mine inspectors to detect such phosphor tags and therefore to establish if non-permissible explosives were used. This new lamp is powered by a Miner's cap battery without interference with the normal lighting requirements of the cap lamp battery. It is compact, light, and rugged with very high ultraviolet output.

Jan 1, 1977

By J. M. Kuchta

Bench-scale test methods were developed by the Bureau of Mines for use by the Department of Transportation in the classification of solid and liquid oxidizers. A burning rate test is recommended for evaluating the fire hazard of solid inorganic oxidizers when mixed with a red oak sawdust as the reference combustible. A spontaneous ignition test is proposed for evaluating liquid and solid inorganic oxidizers which may decompose violently or ignite spontaneously when unmixed or mixed with the wood sawdust under unconfined conditions. Test results are compared for various representative oxidizers and a classification system is proposed for use in the government transportation regulations.

Jan 1, 1972

By Jeffrey S. Walker

The purpose of this U.S. Bureau of Mines effort was to determine if ground movement caused by mining-induced subsidence is directly transferred to a structure and, if so, how that transfer takes place. Four concrete block walls with foundations were constructed and monitored over an active longwall panel. Three of the walls were located perpendicular to the direction of mining in zones where maximum inclination, maximum tension, and maximum curvature were predicted to occur. The fourth wall was constructed along the centerline of the panel, parallel to the direction of mining. All of the walls and the surrounding ground surface were instrumented with conventional survey monitoring points and extensometer stations to observe the vertical and horizontal movements. The fourth wall instrumentation also included continuously recording tiltmeters. The results of this investigation indicate that these simple structures respond to subsidence in a similar manner as the ground surface. This suggests that once the transfer mechanism is more fully defined, prediction models can be developed to accurately estimate the effect of mining on surface structures.

Jan 1, 1989

By John B. Gustavson

Gold was first discovered in Alabama in 1830. Before a decade had passed more than 20,000 people were employed in the various gold districts scattered across east-central Alabama. By 1849 most of the presently defined gold districts were known with such towns as Arbacoochee, Chulafinnee, Goldville, Pinetucky, and Idaho being the principal mining camps. The California gold rush of 1849 signaled the end of intensive prospecting in the Alabama Piedmont for the precious metal. Reactivation of many of the old gold districts has been attempted several times since 1849. Significant activity and development took place between 1874 and 1880, 1888 and 1916, and 1929 and 1936. Locally, some of the development met with moderate succes. The last productive gold mine in Alabama ceased production in 1935. The sharp increase in gold prices since 1973 has caused renewed interest in the potential values of gold of the Alabama gold districts. Most of the gold workings have been abandoned for nearly 75 years and are for the most part inaccessible for convential property evaluation. The early gold miners and prospectors in Alabama were more intent upon finding and mining the valuable metal than in recording their activities for future generations. No matter how interesting or historically significant these records might have been the miners kept no records and left behind them few maps as clues to their activities. Inasmuch as most of the old gold districts have been extensively mined and prospected during the past 150 years, there is very little chance of finding large deposits through conventional outcrop prospecting methods. Similarly, the present geologic knowledge of the various districts is insufficient to launch successful exploration programs looking for large blind lode deposits in new locations within the general gold bearing region.

Jan 1, 1975

By F. Taylor Ostrander

Some countries are infinitely poorer than others in mineral resources-despite the perfect equality of their political leaders ambitions. Compare the mineral poverty of Kenya and Tanganyika with the riches of Katanga Province and Northern Rhodesia. Compare Paraguay with Chile, There never has been any equality in the distribution of nature's wealth. Minerals cannot play any role at all in economic development where they don't exist, and there are bound to be differential rates of economic development where there are basic differences in the wealth of mineral resources available. Africa is my principal area of interest and I know that there is an unfortunate but widespread misconception about Africa's "vast mineral resources, "its "untapped mineral wealth." Why is it untapped? Why is it undeveloped?

Jan 1, 1963

By Harry V. Warren

Introduction Any person concerned with the welfare of mining in British Columbia cannot help being perturbed by the fact that the industry, to an alarming extent, is living on its capital. The great majority of mines and mining camps of today represent a heritage handed down by the prospectors of yesterday. It is true that mining engineers, geologists, mineral dressers, metallurgists, and their fellow scientists and engineers have played an honourable, indeed a vital, part in he1ping to make our producing mines, often after costly and extensive underground development and extended researches. It is also true that the mineralization at the Sullivan, Britannia, and Copper Mountain mines was all discovered before the turn of the century. Likewise the Cariboo, Bridge River, Hedley, Ymir, Rossland, Boundary, Slocan, Salmo, and Portland Canal mining areas, although they had not all been developed, were all known more than fifty years ago. Furthermore, every one of these camps owed its discovery and eventual exploitation to the fact that encouraging ' mineralization occurred at the surface. Where would the mining industry of British Columbia be today had those precious outcrops been buried beneath twenty to forty feet of glacial drift or other overburden? Anybody familiar with the geology and geography of British Columbia will probably agree that finding new mining camps is going to be an increasingly difficult and costly business: disappointments there will be in abundance. Nevertheless, most persons will probably also agree that other valuable mines and even mining camps await discovery by those who will prove resourceful and lucky enough to unearth them. It has become increasingly obvious to the authors of this paper that any new too1s which can aid either prospectors or engineers in their search for new orebodies should be welcome. This paper outlines our efforts to develop biogeochemistry and related techniques to the point where they may be considered as useful tools in the search for hidden mineralization.

Jan 1, 1950

During 1940, the Bahrein Island field produced a total of 7,073,919 bbl. of crude oil- an average of 19,328 bbl. per day. This is a decline of 514,635 bbl. from the I939 production of 7,588,554 bbl. At the end of 1940, there were 70 producing wells.

Jan 1, 1941

During 1940, the Bahrein Island field produced a total of 7,073,919 bbl. of crude oil- an average of 19,328 bbl. per day. This is a decline of 514,635 bbl. from the I939 production of 7,588,554 bbl. At the end of 1940, there were 70 producing wells.

Jan 1, 1941

By T Ladinig

Raise caving is a novel cave mining method, which has been proposed for mass mining at increasing mining depths in LKAB operations. The method makes use of the raise mining technology and an active stress management approach. For the implementation the method is split into two phases, namely a de-stressing phase and a production phase. In the de-stressing phase, a slot-pillar system is established. The purpose of slots is to provide stress shadows and the purpose of the large pillars is to control stress and seismicity. The production phase follows after the de-stressing phase. Required infrastructure in the production phase is developed delayed in stress shadows and bulk extraction takes place in de-stressed zones. Eventually the pillars crush and they are extracted in the production phase. A comprehensive research and development program has been launched to develop the raise caving method towards implementation. As part of this program a full-scale test site of raise caving will be conducted as well as raise caving operations are planned for depth extensions in LKAB mines. This paper discusses the design of raise caving operations in practice at the LKAB mines. In particular, the purpose of the paper is to focus on requirements for the development and design of a raise caving operation. The development of raise caving is discussed from a systems engineering perspective as well as from a management perspective. The functional requirements in the destressing and production phase are outlined and discussed in the paper. The discussion is on basis of the main elements of the raise caving system, such as slots, stopes, pillars and infrastructure. Critical rock engineering design requirements in the de-stressing and production phase are highlighted and dependencies between individual main elements are identified. The analyses show that pillars are especially important for the success of the mining method. Overall, the analyses show that raise caving is a complex system and that its development demands a multidisciplinary approach.

Mar 29, 2023

By Mark Sanders

This report describes an experiment which was conducted to compare the relative bumping hazard of a low and high profile hard hat (helmet) in a low seam mining environment. The study was specifically designed to assess the effect of lowering the helmet profile on frequency of head impacts in an underground low seam coal mine simulator. This involved subjects performing four common low coal mining tasks wearing the low and high profile helmets in the low seam simulator (36" and 48? heights). The results of the study indicated that a low profile helmet could reduce bumping frequency in underground low coal approximately 25%, and as much as 80% on selected tasks. It was beyond the scope of the study to measure the impact force, thus it was not possible to estimate the effect of the low profile helmet on severity of impacts underground. The research team recommended that a more extensive investigation be made of head injuries experienced in low seam mining (both underground and surface) with the objective being to assess the impact of a low profile helmet on total head accident exposure.

Jan 1, 1980

By Jonathan G. Price

Silver-copper-lead deposlts in Precambrian, Permian, and Cretaceous red-bed sequences near Van Horn, Texas, have the following features In common: (1) mineralization controlled by steeply dipping fractures in sandstones, (2) lack of ore In overlying and interbedded limestones, (3) absence of igneous intrusions, (4) sulfide ores without typical hydrothermal gangue minerals, and (5) associated arsenic, molybdenum, zinc, and cadmium but not gold. Ore was probably deposited along fractures by reaction between low-temperature, oxidizing, metal-rich ground waters and sulfide-bearing waters or rocks. Detailed mapping and studies of fracture patterns indicate that mineralization occurred during Basin and Range extensional deformation, thereby postdating major Trans-Pecos igneous activity.

Jan 1, 1983

By Thomas H. Wilson

Common offset and refraction seismic data have been collected over four longwall panels at two different locations within West Virginia. Surveys prior, during and after mining were made in both areas. The velocity of seismic wave propagation in the overburden rocks is observed to decrease in response to panel emplacement. Variations in the magnitude of this reduction, apparent as an additional first arrival time delay in the after mining common offset surveys, do not appear to correlate directly to the amount of subsidence that has occurred. Velocity reduction and signal absorption zones are also produced in the cover beyond the panel face over the adjacent unmined areas. Signal absorption and velocity reduction zones have also been observed over room and pillar entry areas between mined panels. Velocity reduction zones have been- observed beyond the panel face in both shallow and deep mines, but the signal absorption zone has not been observed over the deeper mine. Changes in the compressional wave velocities of the cover rocks are associated with changes in their elastic moduli. Differences between borehole derived and surface seismic derived interval velocities, are related to differences in the properties of the bulk volume sampled by each method.

Jan 1, 1988

By A. G. Fonseca

The effects of coal cleaning, coal combustion and flue gas particulate removal systems on the partitioning of 12 trace elements were investigated. This study was prepared to help document the fate of trace elements in modern coal preparation plants and coal-fired utility boilers. The coal cleaning data were obtained from several coal preparation plant operations. The CONSOL 1. 5 MM Btu/hr pilot combustion and electrostatic precipitator (particulate removal system) test facility was used to develop the combustion systems data. A comparison with the very limited amount of published data from utility boilers is presented.

Jan 1, 1993

By T Trott, M Lewis, G Lumley

The analysis of equipment trends in The AusIMMÆs revision of Monograph 19 - Australasian Mining and Metallurgical Operating Practices (AMMOP) (in prep) in the paper by Graham Lumley raised some interesting, and in parts disturbing, trends in the Australian open cut mining industry. According to the Australian Bureau of Statistics (2011) the productivity of the whole mining industry is down by 34 per cent since 2001. In terms of open cut equipment, median output for draglines is down by 15 per cent since 2003, electric rope shovels are down by 41 per cent since 2003, hydraulic excavators are down by 39 per cent since 2008, front-end loaders are down by 39 per cent since 2007 and trucks are down by 41 per cent since 2006. Clearly e boom has not been good for the efficiency of the mines. During this same time, best practice (defined as the average of the top ten per cent by annual output per unit of input) has declined, but not by as much as the median (eg shovels down by eight per cent, excavators down by 19 per cent and FELs down by five per cent). This paper will build on the analysis of AMMOP to understand the differences occurring between median and best practice and identify the factors contributing to the decline in performance. As the industry enters a period of potentially lower prices for commodities and reduced margins, pressure will be brought to bear on mine sites to start moving more with the equipment they have. An understanding of where efficiency has been lost will be a key component in that. The information contained in AMMOP, and the subsequent analysis of that information in papers such as this one, will be crucial to reversing the decline in open cut equipment performance.CITATION:Lumley, G, Trott, T and Lewis, M, 2012. Reversing the trend in open pit mining equipment output, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 75-82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By T. Warren, R. Pender

"Significant strides have been made during the past decade to integrate the traditionally separate administrative functions of financial management, materials management and maintenance management.In 1983, Key Lake Mining Corporation (KLMC) brought on-stream one of the most technologically advanced mining operations in North America. There was a requirement to support this new facility with state-of-the-art management information systems.This paper will discuss the development and evolution of the corporation's computerized information systems with specific emphasis on the utilization of computer systems to assist maintenance personnel in performing their work activities:Note: In August of 1989, the administration and operation of the Key Lake Mine was assumed by CAMECO - A Canadian Mining and Energy Corporation.IntroductionThe Key Lake Mining Corporation was incorporated in 1979 and operates a $500 million uranium mining and milling complex located in northern Saskatchewan.The feasibility study and environmental impact statements for the Key Lake Mine were submitted in 1979and in August of 1981, following a public inquiry, approval to proceed with construction was granted. Ore processing commenced in October of 1983 and during 1984 a total of 10.4 million pounds of uranium oxide (U3O8) was produced. In 1987, an annual production of 13.5 million pounds was achieved clearly establishing Key Lake Mining Corporation as the world's leading producer of uranium oxide. Current ore resources are expected to extend production of the Key Lake facility into the year 2000."

Jan 1, 1990

By W. L. Price

Recent publication of United States Bureau of Mines figures showed that the sand and gravel (3) industry is the largest single mining industry in the United States in term of yearly tonnage produced. The yearly production of over 500,000,000 tons per year now exceed bituminous coal production. This disclosure caught unawares many observers who have not been following closely the rapid-growth of this phase of mining. Along with this steady growth in production, the sand and gravel industry has gone through an accelerated and varied program of beneficiation in a period of the last ten years.

Jan 1, 1958

By Marco Ojeda, Caio Moreira, Edelink Tinoco

Este documento técnico analiza la viabilidad del uso de un relave minero de la empresa Nexa Resources, cómo componente principal para la producción de cemento. El proyecto contempla dos etapas, en la primera etapa se acondicionan las proporciones de los componentes del relave mediante la flotación para en una segunda etapa hacer el tratamiento térmico del relave acondicionado y así producir el Clinker, que es la materia prima base que se usa para fabricar el cemento.

Sep 29, 2023