Search Documents

By J Szymanski, Y Hu

Excavation engineering involves complex processes for primary and secondary extraction of materials. The shovel excavators bear varying mechanical energy input and stress loading across the working bench during excavation. These varying mechanical energy input and stress loading effects cause significant wear and tear and fatigue failure in equipment components. These effects further result in unplanned downtimes, reduced efficiency and high production costs. In addition, the mechanical and electrical control systems must be operated in efficient profiles to generate maximum outputs and efficiency from these excavators. Efficient technologies are therefore required to solve these problems in order to reduce production costs and increase efficiency. In this paper, the authors develop a rigorous simulator for a hydraulic shovel in a surface mining environment. The finite element model is used to capture the stress profile within the shovel components during excavation, such as, the bucket, stick and boom assemblies. The profiles are classified into normal, critical and extreme ranges, with appropriate corrective measures to avoid extreme loading conditions. The loading capability of shovel excavators can be examined by assessing its structural strength against all possible maximum loads working on the equipment. The dynamic model is used to define efficient profiles of the critical structural components of hydraulic shovels during digging operation. This assessment is used to locate the maximum possible loads and the critical sections of the structures. The method presented in this paper forms the basis for developing comprehensive simulator models for efficient shovel operations in constrained mining environments.

Jan 1, 2003

The BHP Steel Group embarked on a Total Quality Control (TQC) programme in 1984 in response to enquiries from a major customer regarding procedures for quality in materials supply.The TQC initiative has been adopted by all seven Divisions of the Steel Group and covers a broad and comprehensive range of management and workforce improvement initiatives.The development of the TQC initiative in the Collieries Division of BHP Steel over the past eighteen months has resulted in important experiences and leanings.

Jan 1, 1991

By J. E. Burke, C. S. Barrett

THE fine lines shown in Fig 1 are typical of markings that may be detected after polishing and etching deformed specimens of alpha brass and other alloys. Although they have long been the subject of discussion by metallurgists their nature is still uncertain and the names that have been applied to them, such as deformation lines or strain markings, indicate this uncertainty. In this paper which reports the results of a further investigation of their nature, they will be called strain markings. INTRODUCTION Matthewson and Phillips1 in 1916 concluded that strain markings appeared only after deformations that exceeded 20 pct. They objected to the markings being called slip lines believing this term should be reserved for surface markings produced by plastic deformation. In 1921, Vogel2 described similar striations which appeared after polishing and etching the roughly ground surface of numerous alloys. He reported that the markings were crystallographic in nature, and since they resemble Neumann bands in iron, at least superficially, he assumed them to be mechanical twins. In 1928, Matthewson3 reported work by Phillips which indicated that the lines were more readily produced by impact than by slow deformation and that in many cases the twins inside recrystallized grains were parallel to strain markings in the original deformed grains. This was taken as evidence that the markings coalesce into annealing twins, and hence that they themselves are mechanical twins. Many attempts have been made to [ ] demonstrate directly that the markings are mechanical twins. In 1934, Samans4 described the results of X ray studies of two deformed crystals of alpha brass. Evidence was obtained which could be interpreted to indicate that the strain markings are mechanical twins, and this remains the only direct evidence to this effect. Several other attempts to obtain similar evidence by X ray diffraction have failed5,6,7 although in no case was the original method of Samans employed. An

Jan 1, 1948

By John S. Summer

The induced polarization (IP) method of geophysical exploration is capable of detecting even small amounts of metallic luster minerals in a rock mass. Consequently, in the years since discovery, IP surveying has become the most popular ground geophysical survey method. It is not too difficult to understand many applications of IP surveying as used in the search for mineral deposits. However, the basic theory of the IP phenomenon is not well developed or understood, and there has been some disagreement on fundamental concepts. In order to most effectively apply the IP method in the field it is necessary to know the physical characteristics of the sought-for deposit including its size, shape, depth, and electrical properties. With this information an optimum IP search arrangement can be devised and one could use the best possible electrode interval, type of array, and line spacing. With uncertain target characteristics as encountered in the real world, geological guidance must be used to help direct an optimized IP survey.

Jan 1, 1972

By A. D. Hughes

C. W. MERRILL*—Mr. Hughes' paper not only is very well presented but is most timely in that it covers a subject of vital interest to the United States. Tin is one of the strategic metals which has not been found here in appreciable quantities. The total United States tin output since the first recorded production over 100 years ago would not supply current consumption for a fortnight. On the consumption side, tin is extremely important in national defense because of its use in tin plate which, in the form of tin cans, makes it possible to feed properly the armies that the United States recruits from its civilian population in emergencies. Moreover, the internal combustion engines so important in powering tanks, planes, and other war machines, require large quantities of tin alloys for bearings and for soldering. These considerations, along with the fact that Malaya, historically, has been the leading source of tin to the United States, make the kind of information that Mr. Hughes has presented so ably. a matter of vital interest. Your Chairman, Mr. Romanowitz, in his introduction, referred to the fact that I had been a member of the United States delegations to the three meetings of the International Tin Study Group. Some cominents on the Group's objectives and deliberations may be of interest. When it appeared that the International Tin Committee, the prewar producer's cartel, might soon revive its operations and extend its control agreement beyond the expiration date of Dec. 31, 1946, the United States Government became interested in some kind of an international trade organization concerned with tin which would give the consumers' interest equal representation with the producers' interests. An international meeting was called in London in October 1946 to consider this problem. I did not attend that meeting hut the result of the meeting was the organization of the International 'Tin Study Group which

Jan 1, 1950

By Edgar Rickard

IT SHOULD be clearly understood that my remarks on economic conditions in Russia are entirely personal, and not official as an officer of the Ameri-can Relief Administration. The American Relief Administration is concerned exclusively in relief operations. The American Relief Administration has played a large part in the conditions as they exist in Russia today and it does not seem to be out of order to give you the high lights of the work accomplished. SIXTY MILLION DOLLARS FOR RUSSIAN RELIEF The Riga Agreement, by which we were enabled to carry on our operations, was signed in Riga on Aug. 20 of last year. On Sept. 8, we opened our first relief station in Petrograd. On Sept. 18, our first food was handed out in Samara on the Volga River, in the center of the so-called famine district. Altogether over 775,000 tons of food have been sent from the Atlantic Coast into Russia and we have moved this entire quantity of food over a dilapidated and wornout system of railways; and we estimate that our loss will be less than one-half of one per cent. in shortages and thefts. We have had available for this Russian work approximately $60,000,000. The bulk of this money was derived from a Congressional grant of $20,000,000 for food stuffs, a further Congressional grant of Army medical surplus supplies of $4,000,000, a grant by the Soviet Government of $11,400,000. This Soviet grant is a rather interesting phase of our operations. In all of Mr. Hoover's relief work abroad he has demanded of the country receiving relief that the people them-selves do something concrete for their own good before he would undertake to collect large sums of money in America. Secondly, before he was willing to go before Congress and ask for funds from our government he desired that the Soviet Government show their good will.

Jan 11, 1922

By D. K. Crampton

INTERNAL stress and season cracking in brass have been studied for many years and the technical literature contains many data on various phases of the subject. A résumé of the literature shows certain fairly well established points upon which various authors are mostly agreed: 1. Season cracking is primarily caused by the presence of relatively high internal stresses, or possibly in some cases by external stresses, or both. 2. A specific corrosion is also essential to season cracking: Certain agents, particularly mercurous salts, mercuric salts and ammonia salts; have such a specific corrosive effect. 3. The tendency to season crack under given conditions increases with increasing zinc content, brass containing less than 20 per cent zinc being relatively immune. 4. In alpha brass the season cracks are intercrystalline; in alphabeta brass they lie between the two constituents; and in beta brass they are transcrystalline. 5. The ordinary impurities or added elements in special brasses have little or no effect on the tendency to season crack. 6. Internal stresses can be eliminated, or at least reduced to a safe 'limit by annealing treatments at temperatures that do not produce visible microstructural changes or appreciable softening of the worked brasses. There are, however, some points in connection with the phenomenon of season cracking which have not been thoroughly investigated, or wherein different authors and investigators are not entirely in agreement. The investigations described in this paper were undertaken to determine: 1. The correlation between mercurous nitrate tests and actual season cracking on long-time atmospheric exposure. 2. The quantitative effect of type and degree of drawing operations on the intensity of internal stress and on the tendency to season crack in brass tubes. 3. The possibility of drawing high-brass tubes in such a manner as to prevent the occurrence of harmful stresses rather than to find a remedy for such stresses once having obtained them.

Jan 1, 1930

By Zay Jeffries

THIS paper will include a brief discussion of Prof. Howe's paper on The Supposed Reversal of Inheritance of Ferrite Grain Size from that of Austenite.1 The general subject of grain refining in steel and iron will also be treated. The conclusions reached are stated in the following hypotheses which are discussed more in detail below. 1. The ferrite grain size in pure iron, the ferrite and pearlite grain size in hypoeutectoid steel, the pearlite grain size in eutectoid steel and the cementite and pearlite grain size of hypereutectoid steel are not inherited from the grain size of the mother austenite. 2. The only structural feature that is generally inherited from the austenite of hypo- and hypereutectoid steels on cooling through their transformation ranges is the position of the excess ferrite or cementite at the austenite grain boundaries, sometimes causing complete and sometimes incomplete networks which outline the old austenite grain boundaries. Rapid cooling through the transformation range will cause the non-inheritance of this structural (network) feature. 3. The austenite grain boundaries themselves are nearly always effaced in all steels and also in pure iron during the Ar transformations. 4. The grain-size refining of steel and iron is brought about by the combined. effect of non-inheritance of the transformation products on either heating or cooling, i.e., the austenite transformation .products do not inherit their grain size from the austenite on cooling through the transformation range for does austenite inherit its grain size from the products which form austenite on heating. 5. In general, in both iron and carbon steel the larger the austenite ,grain size, the larger will be the grain size of the transformation products on cooling. This, of course, assumes all other conditions constant except the austenite grain size. An exception is found to this general rule in very pure iron such as electrolytic iron. 1n this instance small austenite grains may form very large ferrite grains on cooling through Ar3.

Jan 11, 1917

By G. Bruggeman, K. G. Kreider

Grain boundary dij]usion coefficienls were measured in tungsten between 1400° and 2200° C and can be expressed by the equation sq cm per sec This activation energy confirms some eavlier estimates made .from tungsten sintering experiments. Grain boundary diffusion was found to occur in sub-bozrndavies having -misorientations of less than 10 deg. The actiuation energy for this subboundavy diffusion is equal to that for dijjusion in incoherent grain boundaries with in the limits of error. This is shown to be consistent with the dislocation model of Low-angle boundaries wheve diffusion occlcvs along- the dislocation 'YPipes" comprising -tile boundary. RECENT investigations of the sintering of tungsten powders all report activation energies which are considerably less than the activation energy for tungsten volume diffusion. Kothari' reports a value of 100 * 5 kcal per mole, Hayden and Brophy' obtained 90 kcal per mole, and Vasilos and smith3 found 110.7 kcal per mole from their sintering studies. Since most determinations of the activation energy for volume diffu-sion4-' fall between 120 and 160 kcal per mole (the true value seems most likely to be nearer 150 kcal per mole), the conclusion is drawn that the mass transport leading to densification during sintering is accomplished by grain boundary diffusion. This interpretation is consistent with various diffusion models of the sintering process. 10-12 Vasilos and Smith calculate diffusion coefficients from their data which fit the equation D * 1.36 x 10* exp(-llO,700/HD However, no direct measurements of tungsten grain boundary diffusion have been made. Furthermore, considerable disagreement exists between the directly measured values of tungsten volume diffusion.'-' In order to corroborate the inferred results of the sintering experiments concerning grain boundary diffusion and to provide accurate diffusion data essential to the analysis of the kinetics of creep, oxidation, precipitation, and so forth, the present work was undertaken to measure self-diffusion in single-crystal and polycrystalline tungsten between 1400" and 2200°C. It is within this temperature range that tungsten sintering is done, the re crystallization of tungsten occurs, and the widest application of tungsten as a high-temperature material will probably be made. EXPERIMENTAL PROCEDURE Radioactive WlE5 was produced by irradiating tungstic acid in a neutron flux of 1.2 x 1012 neutrons per sq cm per sec for 36 hr. A 2-week waiting period was allowed for the decay of w"~ also produced by the irradiation. (w"~ has a half-life of 24 hr.) The half-life of the remaining isotope was determined to be 75 days confirming the presence of w lE5 and the absence of any undesired radionuclide. Specimens 4 in. in diam and $ in. thick were cut from polycrystalline swaged tungsten rods (recrystal-lized) and from Linde single-crystal rods. Chemical analyses of these materials appear in Table I. Actually upon closer examination, the single-crystal specimens were found to consist of several subgrains separated primarily by tilt boundaries in which the misor-ientation ranged from 3 to 10 deg. Thus, it was possible to measure boundary diffusion coefficients in these low-angle subboundaries as well as in the incoherent boundaries of the polycrystalline specimens. The two faces of each specimen were ground flat and parallel within 0.0001 in. The radioactive tungstic acid was dissolved in concentrated ammonium hydroxide, placed on the ground flat of the specimen, and evaporated to dryness. The oxide was then reduced in hydrogen at 1000°C resulting in a layer of wlE5 approximately 1 p thick. The diffusion anneals were performed in vacuum in a tantalum resistance furnace. Time at temperature ranged from 10 hr at 1400°C to 2 hr at 2200°C. The penetration profile was determined by measuring the residual activity after successive removal of surface layers by grinding on metallographic polishing paper. Extreme care was exercised to insure that sections were always taken normal to the diffusion direction; this was verified repeatedly by checking that front and back surfaces of the specimen remained parallel. The activity was measured with an end-window Geiger-Mueller counter. The sides and edges of the specimen were well-shielded to eliminate possible effects due to surface diffusion. The weight of the

Jan 1, 1968

By Peter Stamos

In the summer of 1989, Material Service Corporation (MSC) was expanding its Thornton limestone mining operation putting them in close proximity to two shopping centers in Homewood. In other communities, similar expansions had been met with community protests and lawsuits seeking injunctions to stop operations.

Jan 1, 1991

By M. A. Roche

AST fall over half a million tons of ore and rock were broken in one blast at the open pit of the Hudson Bay Mining & Smelting Company's operation, at Flin Flon, Manitoba. The following particulars of the blast, and details of the preparatory work, indicate how an operation of this scope is carried out. The data given, in essentially the present form, were first published by The Canadian Mining Journal. The area blasted was 150 ft. wide and about 700 ft. long. A total of 123 tons of 50 per cent forcite gelatin, in 5 by 16-in. cartridges, was used for the charge. Drilling for the blast was started on May 29, and was completed late in August, requiring 1297 machine shifts for drilling only. Total footage drilled for the shot was over 5 miles of 6-in. hole. The main blast consisted of 232 holes spaced on 17.5-ft.

Jan 1, 1934

By John G. Banker

Titanium/steel clad has been selected as the material of construction for six pressure acid leaching autoclaves for nickel production from laterite ores. These six pressure vessels are now in production service in western Australia. Titanium provides reliable corrosion protection in the nickel laterite pressure leaching environment. Clad metal construction offers a significant cost reduction for equipment of this type in comparison to solid titanium. Clad metal construction offers superior durability and reliability in comparison with non-metal or titanium loose-lined equipment. Experiences in titanium clad equipment construction and performance are reviewed. The presentation addresses aspects of design, fabrication, and testing which are necessary to assure reliable equipment. The explosion cladding proces and titanium alloy selection considerations are also discussed.

Jan 1, 2000

Despite extensive oil exploration in"Western Australia over the past 12 years no commercial oil fields have yet been found. A total ' of 66 test wells have been drilled throughout the State but only Rough Range No.s.. 1 and 1A have produced oil in significant quantities. Active oil exploration is now in progress in the" Canning, Carnarvon, Perth, Bonaparte Gulf and Officer Basins. Test wells have been drilled' in ,all of these except the Officer Basin, where the subsurface stratigraphy is still unknown. Large .areas of the other four have hot yet been drilled. It, is- probable that. commercial oil deposits will eventually be found' in these basins as they contain thick marine sequences, and have structures 'suitable for.,the. entrapment of oil. .

Jan 1, 1964

By M. K. Pathak, A. K. Mukhopadhyay, D. C. Panigrahi

Changes in machinery operating and design parameters often result in unexpected vibrations or changes in the vibration patterns. Vibration in a system is an undesirable element that can cause machinery distress. Potential damage can be prevented by identifying the vibration level that is due to the changed operational parameters. This is necessary for the safe and reliable operation of plant equipment. This paper presents a documented study on vibration events that resulted from alterations in operating and design parameters in a mine ventilation fan and analyzes the causes by defining the sequence of events that led to its performance deficiency. This paper is based on experimental effort to study the vibration behavior of a ventilation fan under varying operating conditions.

Jan 1, 1999

By Yang RL, Bailey ML

During overburden blasting operations in dragline pits, coal edge losses along the lowwall edge of the new pit are often experienced. In tonnage terms, losses can be significant. With the thick seams at Callide Mine, 20,000 tonnes of coal can be lost along a 600 metre pit. In addition to the immediate dollar value of the coal, replacement of this coal (from which overburden has been removed) will be from higher ratio and higher cost pits in the future. Unit costs of production for the remainder of the coal uncovered in the current pit increase. Experiments involving variation of blasthole inclination and/or amount of standoff on the front row of blastholes have given no significant improvement in the coal edge loss control.

Jan 1, 1988

By John K. Hammes

INTRODUCTION From the point of view of the consumer, the cost of mineral commodities might be viewed as the total price industry pays for mine output. Similarly, the mining company engaged in the ongoing business of finding, developing and operating new mines is concerned very much today with the distribution of all the revenue paid for mine output and not just with its direct or controllable cash costs. In other words, what will the labor force, the supplier of energy, explosives, and reagents, and the supplier of government services, management, capital, and the ore reserves receive for their contribution to production? A significant amount might be categorized as what economic theory classifies as economic rent. Mining companies are finding it increasingly difficult to negotiate concession or work contracts to develop ore reserves in lesser developed countries, just as they find themselves accused of taking excess profits in their own countries. The principal difficulty in reaching mutually satisfactory agreements in many cases is the difficulty in establishing an acceptable distribution of income, in particular the distribution of economic rent. (See Chapter 7). Further, it is logical that the decisions and policies of the interested parties be they government or industry should be and will be influenced by their competitive position relative to determining the distribution of economic rent. The raising of finance for a mining project today may be inhibited by too biased an extraction of economic rent by entities other than the risk takers, the mining companies. ECONOMIC RENT A British economist (Ricardo D. McGraw-Hill, 1955) first proposed the concept of economic rent (See Drechsler, H.D. earlier in this Chapter.) Ricardo pointed out that no rent would be paid until land became scarce. Ricardo also stressed the distinction that the price of farm produce was not higher because of the rent paid on farm land but that the rent or price of more fertile farm land was higher because the price of produce is higher. This led to the concept that economic rent is not a cost and that it is therefore not price determining, but is itself price determined. Economic rent may be viewed as a cost if cost is equated with the concept of payment or distribution of income to any factor used in production. However, if it is a criterion that a payment must be made to the supplier of the factor of production, then economic rent is not truly a cost because it is not necessarily distributed or "paid" to the supplier. Consider the commodity A which occurs in three grades: Al, A2, and A3. Any grade may be used as a substitute for another grade in all of the industrial uses of A. However, in industries X and Y the different grades have different productivities. Table 1 shows the relative productivities of each grade in industries X and Y, and in all other industries [~]. [ ]

Jan 1, 1985

By Jr NeSmith

"Drilled Displacement piles are a product of screw pile technology originally developed in Europe. The process involves rotating tool into the ground that displaces the soil laterally as it advances, then grouting or concreting through the hollow stem of the tool as it is withdrawn. They were first introduced in the United States in the 1990’s and have become a mature and accepted technology since that time. They are now used to support a variety of heavily loaded structures including electric power and LNG facilities, stadiums and arenas, airports and mid- to high-rise commercial and residential facilities. In urban environments, the technique has a number of advantages including, low noise and vibrations, no removal of the existing soil, and reduced pile material cost due to the improved stress state of granular soils after installation (smaller or shorter piles can be used). For these reasons, displacement piles have been used to support various facilities in Northeastern United States (US). The paper presents case histories of the performance of displacement piles in the Northeastern US including the use of full displacement elements as a settlement limiting ground improvement system.INTRODUCTION“Drilled Displacement” (DD) is an industry umbrella term for a number of proprietary or commercially available cast-in-place pile installation systems which involve a hollow-stem tool that laterally displaces soil as it advances and the placement of grout or concrete through the hollow-stem tool as it is withdrawn. The systems include grout/concrete placement methods by both sand-cement grout pumped under pressure and tremie grout/concrete placement through bottom-hole discharge. The system discussed in this paper includes grout pumped under pressure, also referred to as Auger Pressure Grouted Displacement (APGD). A schematic of the APGD tool is shown in Figure 1. The tools require significant torque and downward force to advance; a typical installation platform is shown in Figure 2."

Jan 1, 2016

By Adrian Smith

14.1 INTRODUCTION From the time the last recoverable gold is extracted from ore on a heap leach, the ore - now spent ore - changes from being the resource, indeed the raison d'etre of the operator, to a potential liability. The spent ore contains process chemicals and constituents leached from the ore both in the interstitial pore water in the heap and on the surfaces of spent ore. If these chemical species were released to the environment, it could have a potential impact on the quality of both surface water and groundwater resources. Accordingly, the spent ore must be left in a condition where it does not present a potential environmental liability. This can be accomplished either on a decommissioned pad or, if the heap leach is operated as a load/unload scheme, in a waste facility. In general, the residual cyanide level in the spent ore is the perceived controlling factor when determining whether the leached material is suitable for abandonment. Regulatory authorities set permit conditions for heap leach abandonment in terms of residual cyanide levels, for example, Smith and Struhsacker (1987). This chapter discusses cyanide degradation and methods for detoxifying a heap leach in order to meet regulatory limits/permit conditions for abandonment. Cyanide degradation and detoxification by "natural" processes are described initially, based on the chemistry and geochemistry discussed in Chapter 13. This leads to a review of chemical treatment processes for detoxification of spent ore. The advantages and apparent disadvantages are then appraised. 14.2 NATURAL DEGRADATION AND DETOXIFICATION For the purposes of discussion, "natural" detoxification processes can be divided into two alternatives: • Passive abandonment (the so-called "do nothing" option); and • Water In the first alternative, the spent ore is merely left on the leach pad to age; the second alternative involves the flushing of the spent ore with water.

Jan 1, 1988

By F. -J. Wodopia

Sustainability of energy supplies has been an issue of general interest for a long time. Whilst in the past the continuous productive use of natural commodities was in the fore, its compatibility with the environment and climate and ultimately also social aspects have recently gained more and more attention. Today many discussions focus on the climate compatibility of individual options to act. Fossil fuels, in particular coal and lignite, are generally challenged because coal use makes a significant contribution to global man-made CO2 emissions. The drastic increase in the consumption of fossil fuels is not explained by the fact that coal utilisation technologies are not or cannot be sustainable but rather by the growing world population and the endeavours numerous national economies trying to catch up economically. Coal is the world’s No. 1 fuel and, in the view of many experts, will keep this position also in the foreseeable future. The access to its deposits plays a significant role for the economies of the emerging countries. Consequently the aspects of energy security and economic efficiency need to be considered at eye level with climate compatibility. In Germany, however, the public acceptance of fossil fuels and of large industrial projects is in the focus of attention.

Jan 1, 2011

By John Griffen

K. F. Tromp (Kerkrade, Holland)—Your assumption that the Dutch State Mines have lead in the development of heavy medium processes—the Barvoys, Loess, Driessen—is not correct. The credit should be given to a Dutch engineer Mr. deVooys, the inventor of the Barvoys process. deVooys started in 1932 in Hiickelhoven, a German but Dutch-owned mine, where he was a director. Several plants on the Continent as well as in Great Britain were erected. The State Mines started their first plant in 1937. They could not get that plant working satisfactorily and built another one. Their process made no headway, and up to 1946 there was only one plant installed, the one at their own pit. Since 1946 they started the cyclone process and only since that time have they been more active, though industrial cyclone washeries are still in their infancy. deVooys sold his patents to the Dutch State Mines in 1946 and this might have given you the impression that the pioneer work had been done by the Dutch State Mines. John Griffen (author's reply)—I wish to thank Mr. Tromp for giving the correct story on the development of heavy medium processes in Holland.

Jan 1, 1952