Search Documents

By P. L. Allsman

A method of analyzing blasting action indicates that major cost savings are possible by revising practice and bringing the classical blasting formulas up to date; difficult problems such as taconite and throw-breakup can be attacked by engineering Denonation pressure — the peak pressure developed by the explosive reaction; "shatter blasting." Average detonation pressure — the average pressure over the time the reaction continues; "heave blasting." Radial presswe — the stress in a radially expanding sphere about the detonation. Corresponds to the diminishing peak pressure. Lateral stress - the stress in a circumferential direction, induced by outward movement of the rock away from the detonation. Limiting stress or Slim— the rock property at which failure will occur in the case at hand; may be tensile or compressive strength, or combinations. Recent developments in explosives technology, following the advent of nuclear explosions, have led to a rather complete understanding of their action. A survey was made for the purpose of uncovering any knowledge which might be applicable in the mining and quarrying industries, the principal users of explosives. Although no revolutionary techniques have become apparent, much basic data pertaining to blasting — fortunately not classified — have been developed by recent research, from which a good general understanding of the process can be derived. It is hoped this explanation of the scientific principles governing explosive action, together with a proposed analysis of blasting practice, will further the development of mining engineering. NATURE OF THE REACTION: The phenomenon of explosion, termed detonation, is in reality a rather complex chemical reaction, and as such is completely explainable by physical and chemical laws. Detonation is characterized by high temperature and pressure, extreme rapidity — often being complete within one microsecond — and most importantly by formation of a shock pulse which accompanies the reaction zone. As with any chemical reaction, there is a critical value of temperature and pressure below which detonation can not occur; this is termed the "critical point". Whereas an explosive substance will decompose slowly at ordinary temperature, with the formation of gases which readily dissipate; at elevated temperature the reaction is considerably speeded. If pressure is suddenly applied at some point in an explosive medium, adiabatic compression results, and the temperature is locally raised. When the temperature becomes high enough the decomposition will be so rapid that the gaseous products do not have time to dissipate, but contribute to a further build-up of pressure. This, in turn, furthers adiabatic temperature rise over a widening area, and with any heat generated by an exothermic reaction, causes a rapid increase in temperature. Both temperature and pressure are spontaneously built up in this manner until the critical point is reached, resulting in detonation. The values of pressure and temperature necessary to create detonation are established by the unusual nature of the process. If temperature alone is raised above the critical point, without sufficient increase in pressure, deflagration or "low-order detonation" occurs. In the true, or "high-order detonation", the shock pulse resulting from the violent decomposition becomes an integral part of the reaction, and itself aids in increasing the detonation

Jan 1, 1961

By T. Melfi, M. James

Attaining required mechanical properties in welds made using the double submerged arc welding (DSAW) process is difficult, and it is becoming more difficult as the strength level of the base materials continues to increase. Producing weld metal with adequate mechanical properties involves factors that are often overlooked and not taken into consideration. Not least amongst these problems is simply finding information to use in selecting the appropriate flux/wire combination. Most of the available data on flux/wire combinations provided by consumables manufacturers is generated using the multiple pass welding procedures required for classification per specifications such as AWS A5.17 and A5.23. This data really gives no insight into the properties that can be expected in a DSAW application. Also, base plate composition plays a very significant role because of the fact that base plate dilution can be as high as 70% in DSAW welds. This means that if any elements are present in the base metal that are deleterious to mechanical properties, they will also be present in significant quantities in the weld deposit. Some of these elements can decrease toughness and increase hardness (increased hardness is a concern if the pipe is intended for sour service). Some of these problems can be mitigated by proper selection of welding consumables. Selection of proper welding consumables means selecting an electrode that provides the appropriate alloying elements to obtain the desired level of impact toughness while also keeping the hardness within any specified limits. In order to attain the necessary impact toughness, selection of a flux with an appropriate composition (in terms of its basicity and its ability to control the nitrogen content of the weld deposit) is required. As with all welding processes, the mechanical properties of DSAW welds are also highly dependent on the welding procedures. This work clarifies how to select appropriate consumables to meet a given set of requirements, and also how to achieve the optimum mechanical properties from those consumables.

Jan 1, 2005

By H. E. Hawkes

Reconnaissance mineral exploration based on the distribution of ore metals in stream sediments has become a generally accepted method of mineral reconnaissance. This approach seems to work almost equally well in all climates and in all kinds of terrain, provided of course that the ore deposits being sought are exposed at or near the surface and are actively undergoing erosion. Nobody with any experience in the field would question the validity of the concept on which stream sediment reconnaissance is based. Considerable dispute does arise, however, when the subject of density of sample sites per unit area, or sample spacing, comes up for discussion. What is the optimum balance between completeness of coverage and cost? The tacit assumption is frequently made that a greater sample density necessarily leads to more complete coverage and hence a lower probability of missing an important discovery, without regard for the size of the stream sample or the topology of the drainage pattern. The purpose of this paper is to attempt to bring the problem of site selection in stream sediment sampling into better focus, and to present a formula that may help in planning reconnaissance programs.

Jan 1, 1976

By Alan H. Goode

Of the 15 million tons of glass discarded in municipal wastes annually, about 2 million tons pass through incinerators and can be recovered by ore processing techniques. Although the primary use for this recovered waste glass would be as cullet in the manufacture of new glass containers, this approach is not always practical because of long shipping distances, high freight costs, and high purity requirements. Alternatives to the use of waste glass as cullet would be either as landfill or in secondary products. Although glass is considered a good landfill material, it is still wasteful of potentially valuable raw materials. Secondary products that can be made from waste glass1 include a variety of industrial and construction items. As part of the Bureau of Mines' program in secondary materials recovery, the Tuscaloosa Metallurgy Research Laboratory has conducted research concerned with the development of ceramic building products from waste glass. Materials employed in this research were obtained from municipal incinerator residues fractionated in the Bureau's continuous residue processing plant, College Park Metallurgy Research center.' The studies reported herein3,4 present research results using waste glass in the formulation and production of clay bricks, not only to produce improved products, but to reduce production costs, conserve natural raw materials, and most important, to reduce manufacturing energy requirements.

Jan 1, 1974

By Oliver Bowles

"Conservation of slateWaste slate is a problem of outstanding importance in the slate industry, for a very large proportion of all slate quarried is thrown on the waste heap. While many uses for waste slate have been found, the demand calls for merely a fraction of the present supply of unused material. If the slate industry is to increase in prosperity, the producer's energy must be directed toward the development of ways and means of reducing waste to the lowest possible point. The Bureau of Mines of the Department of the Interior has devoted much study to this problem and a recent bulletin ** contains a detailed discussion of the waste problem.Attention has recently been directed toward an improved method of cutting slate in quarries, a method that promises to reduce greatly the percentage of waste material. The method has been introduced since that bulletin was published, and this supplementary paper covers the details of the process.A reversion in method,In connection with this new mode of operation history is repeating itself in a very interesting way, for the old quarry bar used years ago with steam drills, and later discarded in favor of the channeling machine .and the hammer drill, has been salvaged from the scrap heap, and again put to active use. The occasion for its employment is an attempt to improve quarry methods by the substitution of drilling for channeling or blasting."

Oct 1, 1923

By M. Cambridge

The extractive industries are currently, and will continue to be, major contributors to the world economy, particularly in the developing world where economic growth is dependent upon a sound supply of primary materials. However, tailings dam and other mine failures have been very much a feature of recent anti-mining publicity, particularly in Europe, and thus instrumental in inhibiting new mine developments. Although, superficially, the record of dangerous incidents might support the anti-mining position, closer inspection suggests otherwise. This paper reviews the failures which have occurred over the last 50 years and demonstrates that, though poor practice is an ongoing problem for the industry, the record is one of improvement in both design and practice. Examples are provided of significant events which have led to dramatic advances in design and operation. The paper assesses the improvements made in technology and practice, and concludes that historic events must continue to form the underlying basis for design and operation of future mining projects.

Jan 1, 2005

By J. F. Cuderman

In situ experiments at the Department of Energy's Nevada Test Site (NTS) have extended the technology of propellant-based fracturing to include liquid- filled, uncased boreholes. Previous work had developed the technology for liquid-free, uncased wellbores. Test results show that fracturing behavior is considerably more complex in liquid- filled boreholes than in the liquid-free case. Compared to liquid-free boreholes, liquid-filled boreholes have faster pressure risetimes and lower peak pressures, large hydraulic-type fractures propagating several meters beyond the end of the test zone, numerous oscillations in the pressure history, and variable types of fracturing within a single test region. Multiple fracturing is initiated in the wellbore of a fluid-filled borehole when the proper propellant mixture is used but, unlike fluid-free wellbores where up to eight fractures propagate, only one to three hydraulic- and/or shear-type fractures propagate. Hydrodynamic effects involving liquid compression during borehole pressurization appear to be responsible for the differing phenomena observed in fluid- filled boreholes.

Jan 1, 1986

By Andrew Bellamy

A thorough appreciation of the origin, formation, preservation and geometry of marine sand and gravel deposits is central in demonstrating that their extraction by dredging does not affect coastal processes or marine life. Geological evaluation underpins wave, tidal and sediment transport modeling and assists in predicting the nature and extent of seabed change during and after dredging. Marine sand and gravel deposits in the English Channel, southern North Sea and parts of the Irish Sea are of predominantly periglacial fluvial origin and record long histories of valley and floodplain cut and fill associated with Quaternary climatic and sea level oscillations. In the Bristol Channel, the influence of marine transgression and tidal dominance in sorting proglacial outwash deposits is evident in the distribution of sandbanks, scoured channels and gravel lags of this region. These deposits are relict and are unrelated to coastal sediment dynamics. Their extraction leaves seabed depressions which monitoring shows remain unfilled. The resultant offshore bathymetric changes and sediment removal in over 10 m water depth are not transmitted to the coastal zone as beach drawdown, wave height increases or sediment starvation. Applications for new aggregate dredging permissions in UK waters must be accompanied by an EIA and need to make a convincing case that the dredging will not affect rare or declining species and communities of marine life. Seabed recovery rates post dredging are now investigated and understood with reference to geological setting and the uniqueness of the sediment/biological character (biotope). Investigation of the continental shelf by the Industry and others reveals the large extent of gravel-dominated biotopes relative to commercially viable deposits.

Jan 1, 2004

By Peter F. Pullen

The need to apply the latest available technology to develop better tools and methods to meet problems in the mining industry was recognized by six of Canada's leading mining companies. As a result, MIROC (Mining Industry Research Organization of Canada) was chartered to identify problem areas in Canadian mining and to have research carried out to develop the tools and equipment to meet these perceived needs. The initial activity of MIROC has been in the environmental field, with improved clothing and protective devices being developed by contractors. Work clothing for miners is now being field tested. Respiratory protection and a new personal light source combined in a new "space-age" helmet are about to be issued for testing. Further developmental work is being carried on to offer these units and probably other personal protective devices on an individual basis as well as in a combined package.

Jan 1, 1979

By Greaves J. N

The U.S. Department of Interior, Bureau of Mines, is investigating the treatment of refractory gold ores. Chlorination in the treatment of refractory gold ores is applicable in many low-grade gold operations. When usable, this treatment provides an economic means of consuming sulfides and deactivating disseminated organic carbon. Chlorination, however, is a pretreatment technique that requires the neutralization of the chlorine prior to leaching the ore with cyanide. Research by the Bureau has extended the present chlorination technology to allow for the recovery of gold without the use of cyanide and allow treatment of some ores presently deemed untreatable by gold operators using cyanidation or chlorination/cyanidation techniques. Chlorination without carbon of two carbonaceous ores extracted between 1 and 20 pct of the gold; however, carbon-in-chlorine (CICL) treatments resulted in about 90-pct recovery with a reduction in carbon loading. A statistical design campaign for stripping metallic gold from the carbon loaded in a chlorine environment demonstrated elutions exceeding 90 pct.

Jan 1, 1991

By Chen-Ming Kuo, Esher Hsu

Energy recovery of livestock waste can not only reduce waste pollution but also generate renewable energy and further create economic bene fits. Currently, most of livestock waste in Taiwan is treated as waste without efficiently recycled. This paper aims to explore and evaluate the energy recovery of livestock waste in Taiwan and further provide policy suggestions. Study results show that small farming scale of livestock industry in Taiwan leads to a lower efficiency of biogas energy recovery. Besides, the environment with relative low price of electricity and high invest cost for power generation plant is hard to provide incentive for implementation of energy recovery which has further caused difficulty on policy promotion for renewable energy recovery of livestock waste in Taiwan. Policy reform with increasing FITs and differentiated purchasing rate for biogas power is suggested to stimulate energy recycling of livestock waste in Taiwan.

Mar 1, 2017

By Alden H. Emery, J. J. Forbes

"IntroductionThe data contained in this paper were collected during the course of an investigation which covered 15 representative coal mines in 6 coal-mining States. The purpose of the investigation was to determine by atmospheric sampling how much dust was raised into the air during the various operations of coal mining, such as undercutting with machines, loading coal by hand, and transporting it from the working face to the surface. The data thus obtained were considered from two angles - namely, the possible physiological effect of inhalation and the explosion hazard of the dust. No attempt will be mode to discuss the former factor in this paper.CONDITIONS OF MININGThe mines in which this investigation was conducted were considered representative, and it is believed that the results obtained will suffice for the average dustiness encountered in most coal mines. .All of the coal mined was bituminous, from beds 30 to 120 inches thick. Only the ordinary room-and-pillar system of mining was employed. Daily production ranged from approximately 700 to 1500 tons and the men employed from 150 to 450. Coal was undercut by short-wall mining machines in all mines, with the exception of one in which pick mining was employed. Loading at the face was done by miners; none of the mines used mechanical loaders. Electric drills, both for brushing roof and for shooting coal, were commonly used although some roof work was done with jack-hammers and a. little of both with augers. Coal was hauled by motor, mule, or rope power in end-gate cars with capacities ranging from 1600 to 3600 pounds. With few exceptions, coal was won at the face by dry methods - that is to say, no water was employed fox wetting down the dust either during undercutting, loading, or transportation."

Feb 1, 1927

By R. F. Holub, E. Franco, T. B. Borak, K. J. Schiager

INTRODUCTION According to a recent analysis by Schiager et al.(1981), inhalation of radon daughters continues to contribute the largest risk from exposure to radioactive materials in underground uranium mines. The American National Standards Institute (1973) has published a concensus standard for radiation protection in uranium mines. According to this standard, a monitoring system for radon daughters must be capable of measuring the annual accumulated exposure in working level months within an uncertainty interval of 50% at the 95% confidence level. To satisfy this criterion, uranium mining companies in the USA have adopted a procedure consisting of single or periodic measurements of the air concentration of radon daughters. All of the measurement methods sample a known volume of air through a filter. After a specified delay interval, the filter is analyzed for radioactivity. The exposure rate from total airborne potential alpha energy in units of working level (WL) is estimated from the measured activity on the filter. For control purposes, this measurement establishes whether or not a work area is safe for occupancy by miners. For routine dosimetry, the concentration estimated from the grab sample is assigned to the appropriate work area. It is then assumed that the concentration of radon progeny is equal to the average of the two measurements at the beginning and end of the specified interval. Meanwhile, the work locations and exposure times of each miner are recorded on the daily time card and verified by the shift supervisor. Most cards provide space for 15-minute time intervals. The exposure in working-level hours (WL-hr) for each shift is obtained by summing the time spent in a given location multiplied by the exposure rate (WL) assigned to that location.The exposure of an individual miner to radon progeny is summarized on a weekly basis and commonly reviewed each month. These values are then accumulated in units of working level- months (WLM) during the calendar year. EVALUATION TECHNIQUE AND RESULTS The evaluation of grab sampling methods for monitoring exposure to radon progeny is presented in two sections. The first section examines each method individually according to accuracy, precision, and uncertainties attributed to human errors. The second section includes an analysis of procedures which are common to all measurement methods. The ultimate goal is to determine whether a specific measurement method, or grab sampling in general, can fulfill the criterion that the annual accumulated exposure of each miner be known to within ± 50% at the 95% confidence level. In addition it is essential that the above criterion be satisfied at an acceptable cost to the mining company. The results of each testing procedure are presented in terms of the contribution of the relative uncertainty in the estimates of cumulative WLM. Each of these are then combined to form a figure of merit for the complete monitoring system. The method of combining statistical uncertainties and interpretation of the results is subject to some debate. However, since all of the tested parameters enter into the final computation of WLM multiplicatively, we have used the commonly accepted procedure of combining the squares of the relative uncertainties. We have also assumed that each of the uncertainties is derived from independent random variables and the covariance of any two variables is zero. A description of each grab sampling measuring method is given in Table 1. Also included is the equation used to compute WL from the measured quantities. Accuracy (U A) Our definition of accuracy is based on the uncertainty inherent in any method which attempts to estimate potential alpha energy without unambiguously determining the concentration of the three unknown radioisotopes, RaA, RaB and RaC. (For simplicity, the RaC and RaC' nuclides are referred to in combination as RaC.) The inherent uncertainty strongly depends on the mixture of these three components at the time of measurement.

Jan 1, 1981

By M. Piard

The scarcity of literature referring to mines in the Rockies has compelled the writer to co-ordinate information and advice taken at the very source. Help was gladly given by active inspectors and mine bosses. Although the field is unimportant at the present time, due to its distance from markets for raw coal, it is quite worthy of the attention it is receiving from two continents; for, with the commercial synthesis of liquid fuels, it would become the largest fuel laboratory in the world, provided, of course, that freight cost drops to a low comparative level. As explained below, there are no obstacles to economical and safe operation under anything like the typical outcrop shown in Figure 1. Although coal dust is probably more dangerous in the Rockies than anywhere else, the damp outcrops afford means of control. The abundant gas may be bled to the open air, and the rigid roof will settle gradually under a wide span of opened outcropping. The Panel Retreating Wall The Measures: Coal measures having an attitude similar to that shown in cross-section in Figure x are characteristic of the active coalfield on the Alberta side of the Rockies, and they are also found on large tracts of undeveloped land west of the divide. The small anticlines, not shown in the cross-section, do not affect the progress of a pillar line, provided their crests are connected to the atmosphere by drainage bore-holes.

Jan 1, 1928

By Robert W. Hunt

THE memorable features of American history have been making fast during the last century, and notably so since 1860; and they are by no means confined to political or to any one branch of scientific development. Of all the industrial arts, none show a greater change or a mightier progress than the Bessemer manufacture. And this year, while we are celebrating the first centennial of our national life, we can also celebrate the first decennial of American Bessemer practice. While not forgetting or undervaluing what has been done in other countries, I have thought that a brief history of the introduction and development of the Pneumatic or Bessemer process in America would be of interest. In 1863 the Kelly Pneumatic Process Company was formed and an arrangement entered into with William Kelly, who had taken out letters-patent of the United States, Nos. 16,444 ; 17,628, re¬issued as 505; 18,910, dated January 10th, 1857 ; June 23d, 1857; November 3d, 1857; and December 22d, 1857, respectively. This association was composed of the Cambria Iron Company, E. B. Ward, Park Brothers & Co., Lyon, Shorb & Co., Z. S. Durfee, and, later, Chouteau, Harrison & Valle joined the combination. Not satisfied with possessing the control of the Kelly patent, they sent Mr. Z. S. Durfee to England, to secure for this country Mushet's patent on recarburization, No. 17,389, dated May 26th, 1857, the same having been taken out in England on September 22d, 1856. In this Mr. Durfee was successful. Previous to the application of William Kelly for a patent, Henry Bessemer, of England, had taken out patents dated February 12th, 1856, and August 25th, 1856, in this country. Kelly claimed priority in the discovery of the principles of the process, and the Patent-office allowed his claim by granting him his patents. In the autumn of 1862 Mr. Alexander L. Holley, while in England, was impressed with the importance of Mr. Bessemer's inven¬tion, and so fully foresaw its future, that, upon his return to the United States, he induced Messrs. John A. Griswold and John F. Winslow, of Troy, New York, to join him in endeavoring to possess Bessemer's American patents. Mr. Holley returned to England in

Jan 1, 1877

By Thomas T. Read

Readjustment of the industrial world to a peace basis after more than 4 years of war will involve many fundamental and far-reaching changes that cannot as yet be clearly foreseen or definitely provided for. Such problems may be subdivided, in the vocabulary of war, into those involving material and those centering about personnel. Of the two, the latter group is the more difficult and obscure, as the factors involved are less clearly understood and the methods to be followed are not yet tested and standardized. When it is said that the market is weak, stocks large, and demand light, every business man understands clearly what is meant and what course he should adopt to adjust himself, so far as possible, to such conditions. But when it is said that the rapid spread of Bolshevism in Europe is a danger to industrial organization in this country, it is difficult to have any assured sense that all that the statement may mean is clearly understood or that the means to be followed to meet such a situation are definitely known. Since Bolshevism is primarily a mental phenomenon and since the rupture it brings about in industrial organization should be prevented, if possible, it is my purpose to restrict this discussion of the activities of the Committee on Industrial Organization to some of its mental aspects, as the chairmen of the sub-committees, from their special knowledge of their own fields, can best set forth recent progress in the lines with which they are especially concerned. The first requisites of success in industrial organization, as in the biological organism of which it is the social counterpart, are unity of purpose and coordinated activity. Typical good and bad examples of this' are the relative parts that the United States and Russia have played in the great war. These two factors are primarily mental, and it is not difficult to view the mental aspects of all problems of industrial organization as the most important ones. Unless we can attain unity of purpose and coordinated activity in industry, the provision of comfortable homes at reasonable rent, the assurance of steady work at good wages, the elimination of industrial accidents, and provision against want in old age or in case of disability will have brought us no nearer to our real goal.

Jan 1, 1919

By Lester Uren

The fluid level maintained in wells pumped for oil is an important factor in deter-mining their productivity but one that has received little attention in the literature relating to petroleum-production technology. In the present paper the writer undertakes to show how and to what extent fluid level influences productivity and suggests the use of a fluid level indicator as an aid to the oil producer in maintaining the fluid surface within the well at the proper position. IT is realized that the depth of fluid maintained in a pumping well is sometimes influenced by other considerations than the quantity of fluid that will enter the well: the prevention of sand incursion, prevention of waste of natural gas, and the maintenance of a suitable submergence for the pump, for example. These latter factors have an important influence on the productivity of the well, so that otherwise unwarranted fluid levels must sometimes be maintained to offset them; but where the handling of unconsolidated sands is not a problem of consequence and where water has been properly excluded, the principles developed here and the practices recommended, should apply. The principal objective of the producer should be to produce the maximum quantity of oil in the shortest possible time. Any method or equipment that will increase the rate of production during the early years of the life of the well, when gas pressure is high, will greatly augment the .ultimate production. The maintenance of a proper fluid level in the well at all times will go far toward accomplishing this desired result. For a given set of conditions surrounding the flow of oil into a particular well, in which the viscosity of the oil, the porosity and grain size, of the sand, and the diameter of the well appear as constants, two variables determine the quantity of oil that will flow from the sand into the well. These are: the effective pressure behind or within the oil in the reservoir sand, and the fluid level maintained within the well.. The former is the expulsive force that causes movement of oil from the sand into the well, while the latter determines the magnitude of a resisting force opposing such movement. The first of these factors is largely beyond the control of the oil producer, but it is in his interest to reduce the opposing force to the lowest economic limit.

Jan 2, 1925

By H. M. Rutherford

The reflection method in seismic prospecting has aroused much interest in the past few years. The purpose of the present paper is to present the method of reflections in the mapping of geologic structure and also to give some indication of its limitations. The reflection method is well adapted to the mapping of geologic structure in the Mid-Continent fields, and has been found most useful there. The refraction method is ideally suited to the finding of structures, such as domes, where the amount of relief is very large. This explains the brilliant success of the refraction method in the Gulf Coastal region of Texas and Louisiana. The additional fact that salt has a much higher velocity than the surrounding sediments made their discovery much easier. By the use of the reflection method, differences of relief of 25 to 50 ft. to the mile may be detected at a depth of 5000 ft., and the depth points accurately plotted on a map. This is hardly possible by the use of the refraction method. The reflection method has been in almost continuous use in the Mid-Continent area since 1926, but very little, if anything, has been published until recently'(7) † regarding either the method or the results. The discovery of several oil fields is now attributed to the use of the reflection method. Reflection methods have been used by the Germans to find the thickness of the ice of several glaciers. (2,8) The depths there considered were of the order of only a few hundred feet. For the method to be of any practical value in this country, it must be able to work to depths of several thousand feet. As was indicated above, this is now possible, though there are many problems connected with the reflection method yet to be solved. The refraction method requires that the shooting be done over long ranges. It was necessary, for example, to take distances out to several miles in order to penetrate some five thousand feet. Naturally this uses a good deal of dynamite. In the reflection method the distances are much shorter and the amounts of dynamite are much smaller, within limits which will be noted below. The chief distinction between refraction and reflection methods is to be found in the analysis of the seismo-gram. Refraction shooting makes use of only the first arrival of energy

Jan 1, 1934

By J. Richard Tonry

In portland cement manufacturing, the raw materials axe changed to clinker in the burning operation. Generally the rotary kiln is used for this purpose and involves many processes, including pelletizing and nodelizing. This transformation is called clinkering, and is analyzed as now generally practiced in cement making, from the raw material to the resulting clinker.

Jan 1, 1963

By A. W. Fahrenwald

As an aid to studies of grinding, a batch laboratory classifier and elutriator has been developed at the U. S. Bureau of Mines Metallurgical Field Office at Moscow, Idaho, in cooperation with the University of Idaho. It is designed for use in conjunction with other batch laboratory apparatus, such as ball mills and flotation machines. It is shown in Figure 1. Description and Operation of Batch Laboratory Classifier The classifying column is a cylinder 4 feet 2 inches long, of 5 3/4-inch inside diameter, and terminates at its top in a cone or funnel 18 inches in diameter at the overflow elevation. The pressure chamber is of the same diameter as the classifying column, and has a conical bottom; it is provided with two openings, one in the cylindrical portion through which water is admitted, and the other, a small drain hole, in the apex of the conical bottom. The two compartments are bolted together and communicate with each other through the medium of a constriction plate provided with 3/16-inch holes spaced 1/2 inch apart. Constriction plates having any other percentage of opening may be substituted as the needs demand water is admitted to the compartment below the constriction plate at constant pressure. The volume of eater admitted is controlled with a valve. It should be mentioned that the classifying column at the bottom, just above the constriction plate, is glass.

Jan 1, 1929