Search Documents

By Ruddle R. W.

The slags produced in copper smelting are largely composed of silica and ferrous oxide and may therefore be regarded as essentially ferrous silicates. A fair amount of information is available on the constitutions of the liquid slags used in copper smelting and, in this connection, the large volume of work being carried out on steelmaking slags should be helpful. Constitutional diagrams are available for most of the principal systems involved (SiO2-FeO; SiO2-FeO-Al2O 3; SiO2-FeO-CaO; SiO2-FeO- MgO; and SiO2-FeO-CaO-Al2O3) and these show that additions of Al2O3 and CaO reduce the freezing points of SiO2-FeO slags but that additions of MgO increase the freezing point. A certain amount of information is available on the thermodynamics of slags, but much further work on this subject is required. Modern theories of the constitution of liquid slags deny the existence of molecular compounds but consider that liquid slags are mixtures of various ions such as, Fe2+. O2- and SiO4(4-). Little appears to be known of the reactions between matte and minor constituents dissolved in the slag

Jan 1, 1953

By B. A. Filas

Stabilizing fine coal refuse ponds for reclamation at Monterey Coal Company's No. 1 Mine has been difficult. Entrained water in the stored refuse causes liquefaction as reclamation caps are placed, resulting in additional material requirements than originally projected to stabilize the pond surface. Laboratory results indicate that in-place refuse densities may be substantially improved at No. I Mine by converting from a single-point to a managed slurry distribution system. Increased densities result in improved storage efficiency, less entrained moisture and a more stable refuse mass, thereby providing an improved working surface for reclamation and improved post-closure cover stability.

Jan 1, 1993

By W. Song, C. Richards, B. Q. Li

"This paper presents a two-phase flow numerical model for spouting gas-particle flow reactors used in chemical vapor deposition processes for manufacturing heart valves and other biomedical implants. The model is developed based on the Eulerian-Eulerian formulation of gas-particle flows, with the k-e engineering model modified with the presence of particles for the description of turbulent gas flows. In parallel with the numerical model development, physical models are set up, where the particle image velocimetry is used for visualizing the particle flows and spout shapes and heights and optical probes are used to measure the particle velocities. The numerical model predictions are compared reasonably well with the experimental measurements.IntroductionVarious biomedical implant components, such as bone joints, dental components and heart valves, are coated with bio-compatible thin films by chemical vapor deposition in particle-laden chemical reactors [l-5]. In these reactors fine particles are used as packing and supporting media. During the coating operation, these packed particles are fluidized by an upward gas jet from the nozzle, reach a certain height and fall back on the top of an annulus region. These recirculating particles are mainly for levitating the implant components (usually one or two in a reactor at one time) so that every portion of them is equally exposed to the gaseous atmosphere. An equal exposure is critical for forming a uniform, mechanically strong and corrosion-resistant coating on implants. Plant experience shows that the quality of the coating is directly related to a stream of operating parameters such as temperature, particle size and loading, and gas flow rates [6]. Optimization of these operating parameters for improved reactor performance depends crucially upon our fundamental understanding of the physics governing the gas-particle flow, heat, and mass transfer phenomena taking place in these reactors."

Jan 1, 2004

By John P. Turner, Benjamin J. Turner

"Non-destructive testing and evaluation (NDT/NDE) methods have become standard tools as part of the post-construction quality assurance of drilled shaft foundations. In responding to anomalies, foundation designers, owners, and contractors face a number of choices, including: (i) acceptance of a shaft with known anomalies, (ii) further investigations of integrity (e.g., concrete coring), (iii) repair schemes, and (iv) reject and replace. To assist in selecting the best option, analyses are often performed that involve assessing the structural performance of reinforced concrete shafts that may include defective concrete or voids. Currently, the analytical tools for predicting the flexural strength and stiffness of drilled shafts with defective concrete located in discrete regions of the cross section are limited. This paper presents a robust moment-curvature analysis tool for drilled shafts based on the fiber-element discretization method. The tool allows for consideration of anomalous or defective concrete regions in the shape and location that they are believed to exist in the shaft while considering explicitly the nonlinear material behavior of the intact regions based on expected material properties. A case study is used to illustrate the practical application of the analysis to drilled shaft projects.INTRODUCTIONImperfections such as defective concrete or accidental eccentricity of reinforcing cages are an inherent part of the drilled shaft construction process that will occur occasionally even when construction best-practices are followed. Petek et al. (2002), O’Neill and Sarhan (2004), Poulos (2005), and others have described the effects that construction defects can have on the axial and lateral performance of drilled shafts. Our industry has seen rapid progress in recent years in the development and improvement of tools for detecting drilled shaft anomalies, such as gamma-gamma and crosshole-sonic logging, sonic-echo testing, thermal integrity profiling, and even visual inspection with invasive video cameras. Nonetheless, in most cases the wealth of data from these tests is used by foundation engineers to make a fairly “black or white” decision—should the defects be repaired, or should the shaft be rejected? A third option that is not typically considered is to directly analyze the section, including anomalies, and compare the reduced strength and/or ductility to the actual project demands. This option takes full advantage of the data collected during integrity testing, and may provide a justifiable means for avoiding further construction costs and delays, whether for repair or replacement."

Jan 1, 2016

By Charles A. Beasley

Increased technical and legislative analysis by all parties of interest could result in more efficientand better directed regulatory legislation in the mining industry. Efforts to forestall or frustrate legislation through massive lobbying and public relations efforts are seldom effective over time and often lead to more stringent and far reaching legislation than necessary. The Federal Coal Mine Health and Safety Act of 1969 is perhaps an outstanding example of such insufficiences; a future example may well be regulatory surface mine legislation. Although a lack of extensive hard data seldom enables rapid or sophisticated analysis early in the legislative process, even preliminary analysis may be sufficient. Simple statistical analyses of available data, assessment of the legislative rationale, and subjective appraisal of other non-quantifiable constraints to improved mine safety. An average of 115 underground fatalities at an exposure frequency rate of 0.67 can be reasonably expected in the immediate future, under existing levels of technology, degree of regulation, and economic conditions. If gross unrefined estimates of 6 preparation plant, 5 surface, and 30 strip mining fatalities are assumed, the total fatality industry level could be expected to approximate 156 Serious professional, economic, and technical constraints within the the industry probably preclude any major decrease of these accident levels within the near future

Jan 1, 1972

By R. L. Derick

The Orchard Valley Mine, a large underground coal mine located in western Colorado, experienced a major mine fire during an idled Sunday on June 1, 1986. This mine had extensive problems with spontaneous combustion near the coal outcrop. Spontaneous combustion has been determined to be the probable cause of that fire. Preparing for a mine emergency was an on-going task. Once the emergency occurred, much of the preparation work was implemented and aided in controlling the situation. Later, the successes and shortfalls that arose from that emergency were analyzed for future course of action. This paper summarizes the activity that led up to the major fire, the handling of that emergency, the lessons learned, and the changes implemented.

Jan 1, 1993

By Kuo En Chang

Many rare earth - transition metal (RE-TM) compounds absorb/desorb hydrogen reversibly at room temperature and atmospheric pressure. For LaNi5 which is used as a battery material, the electrochemical nature of this process is well known. In the case of Nd-Fe-B which has found wide application as a powerful permanent magnet, the absorption of hydrogen has both significant advantages and disadvantages. However, a fundamental understanding of the hydrogenation process at ambient temperatures and its effect on subsequent corrosion behavior is currently lacking. This paper reports the results of the hydrogenation of NdFeB two alloys, (NdDy)15Fe78.3A10.7B6 and (NdDy)15Fe67Co5V4A12B7, which are compared with that of LaNi5. Results show that hydrogenation can be accomplished by either electrochemical methods or immersion in dilute sulfuric acid. For the latter method, the change in lattice parameter indicates that the level of hydrogen absorbed by the NdFeB particles corresponds fairly closely to an overall composition of Nd2Fe14BH2.7. Cyclic electrochemical charge/discharge experiments show that the maximum hydrogen discharge capacities of the NdFeB, NdFeB-Co-V, and LaNi5 are 40, 60, and 210 mA?h?g-1, respectively. Anodic potentiodynamic polarization measurements and calculated values of icon reveal that absorbed hydrogen in NdFeB-Co-V and the NdFeB may lead to significant increases in corrosion rates.

Jan 1, 1995

By Jon J. Kellar

The adsorption of oleate at the surface of a fluorite single-crystal internal reflection element has been investigated using Fourier transform infra-red/internal reflection spectroscopy (FTIR/IRS). The application of this innovative experimental technique has added a new dimension to the investigation and understanding of collector adsorption phenomena. It is now possible, for the first time, to measure in-situ and in real time the adsorption density and bonding nature of collector species adsorbed at mineral surfaces. In this regard, oleate adsorption densities were calculated from spectral data, and the equilibrium adsorption isotherms were found to agree quite well with other adsorption isotherms reported in the literature. At low equilibrium oleate concentrations(<10-5 M), monolayer-type cover-age was observed in the chemisorbed region. It was found that in this region the adsorption density increases with an increase in temperature, which sup-ports experimental results from previous ex-situ FTIR studies and thermochemical studies in which it was shown that the chemisorption reaction was endothermic. At higher equilibrium oleate concentrations (>10-5 M), the adsorption density increases dramatically at the point of surface precipitation. The oleate adsorbed in the chemisorbed region has a distinctly different spectrum than the oleate adsorbed in the surface precipitation region of the adsorption isotherm. In the chemisorbed region, the oleate appears to be mono-coordinated at the fluorite surface.

Jan 1, 1989

By Gabriel C. Aguilera, Juan Arismendy

"The effect of rheological factors inside of a hydrocyclone is very relevant for the fluid mechanics and for the classification of materials on suspension, since parameters such viscosity and thixotropy are intrinsic variables that depend of the particulate system and the continuous phase; they determine the efficiency of classification. Nevertheless, the exact knowledge of the main characteristics and magnitudes of them inside the hydrocyclone is very difficult because of the geometry of the hydrocyclone, even more if the hydrocyclone is of small diameter. Hence is not possible to make a hydrodynamic study with effects over classification regarding these variables. This work studies the rheological variables inside a small diameter hydrocyclone that works at high pressures, using the information given by a model of Computational Fluid Dynamics (CFD). The model used includes the Reynolds Stress Model (RSM) for the evaluation of turbulence, and the Volume of Fluid (VOF) to study the interaction between water and air, which is very important to obtain regarding the effect of the air core over the performance of the equipment. The validation of the CFD model was done with a kaolin suspension at several conditions of solids contents below the critical volume fraction, without chemical additive aid. These conditions are representative of current work parameters on plant. As result it could be established the ranges of evaluation of rheological variables on specific regions inside the hydrocyclone, and through a rheometric study, based on the mechanic characteristics previously obtained, the main rheological characteristics of the mineral suspensions were determined."

Jan 1, 2014

By J. Visman

"SummaryThis paper is presented as part of a programme to show the steps taken by industry and others interested in supplying a solid fuel of constant quality to 'satisfy a consuming market. The paper deals with the general principles underlying quality control in coal preparation plants, namely, constant quality and close adherance to acceptance limits. It also describes how control of ash content is ""generally hampered by the problem of coal sampling .and the long duration of the ash analysis and how these difficulties may be overcome.Quality control can be effected in several ways. Thorough blending wll reduce variations appreciably, except those of long trend. The latter can be detected by automatic sampling and quick ash analysis. At present, under favourable conditions, a system of half-hourly ash determinations with an accuracy of 0.5 to 1.0 per cent can be realized, to the effect that trends with a 'wave length' of more than two hours cu be eliminated within the limits of accuracy of the ash figures. The general solution of the problem is a combination of blending, accurate sampling, quick ash determination, and statistical analysis of the pattern of ash distribution.The use of statistical methods of analysis, such as the t test and F test, is •discussed at some length in order to emphasize the importance of the correct evaluation of observational data if there is to be confidence in the validity of test results.General ConsiderationsCOAL, as a fuel, is too cheap for a long haul across the country. The limiting distance depends on the price of the local competitive fuels, and, as the price depends to a great extent on quality, so does quality, to the same extent, command the market."

Jan 1, 1952

By R. Y. Wan

Recent research efforts have shown have shown selective solvation extraction of a gold cyanide ion-pair complex from alkaline cyanide solution is possible with organic phosphorus esters. These alkyl phosphorus esters such as tributyl phosphate (TBP) and di-n-butyl n-butyl phosphonate (DBBP) can selectively load gold to rather high levels, even in excess of 30 gpl. However, traditional stripping techniques are not particularly effective. In this regard, gold recovery by direct electrolysis of the organic phase has been found to be an interesting possibility. Further, the rate of direct electrodeposition from the organic phase can be improved significantly by using an aqueous/organic mixture. Direct electrodeposition of sheet gold from loaded DBBP was successfully accomplished at a current density of 8x10 4 amp/cm2 and 55°C from such a two-phase mixture with the aqueous phase as the continuous phase. No appreciable degradation the DBBP was found after 5 cycles of extraction and, electrodeposition. Finally, the applicability of the process strategy for an industrial situation was demonstrated by the successful treatment of waste gold cyanide electroplating solutions.

Jan 1, 1986

By J. B. Clark

In 1933, R. paris1 published a phase diagram for the entire Mg-Ca-Zn system. He reported the existence of a ternary intermetallic phase, Mg5Zn5Ca2, which formed a quasi-binary with the magnesium solid solution. Since then, no extensive work has been reported on the system. Recently however, indications of the existence of a second ternary in-termetallic phase in equilibrium with the magnesium solid solution led to a reinvestigation of the solid phase equilibria involving the magnesium solid solution. The 335°C (635°F) isothermal section was chosen for study. Metallography and powder X-ray diffraction were selected as the best mutually corroborating methods for determining the solid phase constitution. Seventy-six alloys were prepared from singly sublimed (99.95 pct) magnesium, electrolytic (99.95 pct) zinc and USP calcium. The analyses of some of the alloys are shown in Fig. 1. The alloys were melted in a graphite crucible under a chloride flu and chill cast in a split graphite mold. Dif-fusion couples (see Fig. 2) were prepared by casting molten Mg-20 wt pct Zn alloy around a cylinder of Mg-30 wt pct Ca alloy. The alloy samples and the diffusion couples were sealed under argon in Pyrex vials and annealed in a furnace capable of controlling within 1/2°C of 335°C. At the conclusion of the anneal, the alloy samples were quenched in ice water and the diffusion couples were air cooled. Procedures standard for magnesium alloys were used for metallographic examination. Powder X-ray diffraction patterns were taken on a G. E. camera with a 14.32 cm dim using nickel-filtered copper radiation. The redetermined 335°C (635°) section of the Mg-Ca-Zn phase diagram is shown in Fig. 1. TWO ternary intermetallic phases, designated w and

Jan 1, 1962

By Suzanne Young

The effect of LiF additions on liqt.1id1.:1s temperature and electrical conductivity over a wide range of cryolite bath ratios (1.0 to 1.5 weight ratio) was investigated. Results did not agree with multi-regression equations reported by Dewing and Choudhary over the entire region. New regression equations were developed. Reasons? are given for the differences. The models are used to discuss the economic implications of LiF additions to Hali cell electrolytes.

Jan 1, 1985

By T. K. Bundtzen

Placer gold in the Iditarod and Innoko mining camps of western Alaska is derived from a suite of comagmatic, Late Cretaceous to Early Tertiary, alkali-calcic, meta-aluminous. volcanic-plutonic complexes and peralumi-nous rhyolite sills that intrude Mesozoic flysch. Heavy-mineral concentrates from 42 mining operations and streams draining known mineralized areas in the igneous complexes contain placer gold and a variety of ore minerals derived from epithermal to hypothermal conditions of formation. The minerals include cassiterite, ilmenorutile, samarskite, cinnabar, scheelite, chromite, stibnite, silver sulfosalts, monazite, and zircon. Results of the study show that 1) cinnabar. stibnite, and quartz formed with the bulk of the placer gold in an epithermal lode environment, 2) chromite appears to have originated in mafic phases of monzonite plutons and alkalic basalts, and 3) niobium-tin-tungsten-uranium-silver values may have been derived from stockwork accumulations in cupolas of monzonite plutons.

Jan 1, 1987

By NICHOLAS BELLUSCI, D. Erik Spiller, Patrick R. Taylor, VICTOR BRAMAN

Approximately 30% of the world’s production of soda ash comes from mining and processing of naturally occurring deposits of sodium carbonate containing species. Of these deposits, the largest and most profitable have been the trona beds found near Green River, Wyoming. Processing of trona ores is water-energy intensive, particularly due to unit operations of calcination, dissolution, and evaporative crystallization to wield a high-quality dense soda ash product and reject the insoluble gangue species, primarily in the form of oil shale. However, it is speculated that the glass-manufacturing industry, the largest consumer of soda ash, may be able to use a product of a lower grade and consistent level of the insoluble constituents. Thus, pre-concentration of trona ore was investigated using sensor-based sorting, to produce a beneficiated trona stream that would be fed to calcination. The study encompassed preparation of a run-of-mine (ROM) Green River ore sample, selection of 25–75-mm-sized specimens, imaging of the specimens by x-ray transmission (XRT), color, and laser-induced fluorescence (LIF)-based sensors, insoluble analysis of the specimens, and a bench-scale sorting test. Results of the study established that a correlation between the color of the individual ore particles and their insoluble content existed and that a surface detection-based sensor, particularly LIF, was apparently more suitable than XRT to produce a beneficiated trona stream. The bench-scale sorting test demonstrated that a 65% separation efficiency and a 70% recovery of trona could be achieved.

Aug 9, 2022

By Richard V. Ageton, Harry E. Tufft, E. A. Holbrook

When an underground excavation is made, the rock surrounding the sides and top of the opening is deprived of its natural support and tends to fall. Whenever caving takes place, the time and extent of the caving depend on the character and condition of the rock. In strong homogenous rock, such as solid granite, even a large chamber may stand indefinitely, whereas a soft material, such as clay or a loose material like unconsolidated sand, falls immediately if not supported. Weaknesses in the rocks induced by structural features, such as joints, :fissures, bedding and cleavage planes, and fractures produced by blasting, will cause the falling of insecure blocks or slabs unless means are provided to support these in place. In an unsupported mine opening, as a tunnel, the first slight settling or adjusting movement of the rocks (the "initial creep" or "set") is caused by the great weight of overlying material pressing down the rock masses above and around the roof and sides of the opening until they key together in roughly the form of an arch. The rock, after it has adjusted itself to this shape, becomes. selfsupporting. Timbering is necessa.ry in all mining only to support, therefore, those comparatively small blocks or pieces of rock which tend to loosen from the top and sides of the opening during or after the formation 'of the natural rock arch, and which lie between this natural rock arch and the opening. This statement, of course, has its limitations. For example; a layer of strong rock, like limestone, may act as a beam; then only the material under the limestone will need support. Timbering is not, as is commonly supposed by the layman, used to supp!ort the huge mass of rock between the back (roof) of an underground opening and the surface. It would be impossible to place enough timbers in a:ny underground opening to support such a mass. This fact is not'·perceived by all miners.

Jan 1, 1923

By Moraka N. V., van Rensburg M. Jansen

"SynopsisGoing beyond transformation claims contained in employment equity scorecards and industry compliance reports, this article provides qualitative insight into the initiatives employed and challenges experienced by mining companies in a quest to transform the mining industry. Perceptions expressed during in-depth interviews with 10 senior executives showed that the assumption that mining companies are reluctant to transform is erroneous. Results from this study suggest buy-in and commitment to transformation. This article describes specific initiatives undertaken by mining companies to transform. The most notable initiatives include staff recruitment efforts to appoint historically disadvantaged South Africans (HDSAs), staff development initiatives, as well as community development. The findings furthermore contextualize the challenges experienced by industry participants in their quest to transform. Despite accusations that industry participants are not taking responsibility for the implementation of the transformation agenda, government needs to recognize that they too have a role to play and need to appreciate and assist in the current challenges experienced by the industry.IntroductionWe need a mining sector that works. Mining employs over half a million people. It is the biggest earner of foreign exchange in our country. It also contributes about 20 billion rand directly to tax revenue. Mining also makes a far larger contribution as a buyer of goods and services, and a supplier of inputs to other sectors of our economy and other economies around the globe’ said President Jacob Zuma during the 2014 State of the Nation Address (Zuma, 2014). However, despite apparent commitment from government, enforced compliance with social and labour plans, regulations and Mining Charter targets, the South African mining industry is slow to gain local and international investor trust (Deloitte & Touche, 2013; Mashego, 2013).Industry players acknowledge that their context has changed – creating various challenges (Davis, 2014). In the past few years, such challenges included subdued commodity prices, increased working costs, constrained infrastructure, and high labour costs, coupled with poor levels of productivity, strained labour-management relations, an uncertain regulatory environment, and the inevitable maturation of the industry (Deloitte & Touche, 2013; Davenport, 2014). Mining affected communities also became more cognisant of their rights, and politicians more vocal in their expectations from their relationships with the mining giants (Davis, 2014). One of the main issues that contributed to the difficult operating conditions was claims from organized labour and Minister Shabangu that this industry is too slow to transform. Specific claims were made in terms of employment equity, fair salaries and wages for mineworkers, housing and living conditions, health and safety issues, and general working conditions (Limpitlaw et al., 2005; Miningmx, 2013; Shabangu, 2010). These claims were followed by what Gill Marcus, Reserve Bank Governor, explained as ‘unprotected strike action [that] has escalated into an uncontrolled, violent and unlawful landscape, led by a mob mentality in the absence of formal and recognised leaders’ (Mavuso,2013)."

Jan 1, 2015

By Concentrator Staff

"IntroductionA brief literature search will reveal that the information available concerning rod mills and ball mills is quite extensive. This type of equipment is used to treat every element from antimony to zinc. The size and capacity of individual mills, the number of units employed, and the configuration of the equipment within a concentrator add another dimension to the possible scope of this discussion. It would be impossible to treat this volume of material with any degree of thoroughness.It is the intention in this paper to describe the simplest and generally the most typical circuit wherein a single rod mill and ball mill operate in parallel. Some of the subject matter will not be entirely applicable to every installation. However the principles should be generally relevant to most applications.Typical Circuit DescriptionFigure 1 illustrates the arrangement of the equipment associated with a rod-ball mill circuit.Ore is extracted from a fine ore storage bin (1) the capacity of which is large enough to allow .continuous mill operation independently of the mine and crushing plant production schedules. A number of feeders (2) may be employed to control the flow of ore to one or more feeder conveyor belts (3). In larger tonnage operations several such conveyors are employed at least one of which will be equipped with a variable speed control to allow adjusting of the amount of feed reporting to the rod mill. A rod mill feed conveyor (4) accepts all of the ore from these feeder belts for ultimate transfer to the rod mill. This conveyor is normally equipped with a weightometer (5) to monitor the flow rate of ore to the rod mill and ultimately to allow control of this flow. Typically these conveyor belts would be equipped with feed deficiency switches which would give a remote alarm of the fact that no ore is present on the conveyor. The conveyor belts are protected by underspeed monitors which will provide a remote alarm and automatic shutdown of the conveyor in the C'.'~nt that belt slippage occurs. Finally the belts are protected by monitors which will alarm and shut down a belt if it is not running straight in the idlers."

Jan 1, 1989

By J. P. Morris

"INTRODUCTION In the investigation being conducted by the Bureau of Mines concerning the production and utilization of sponge iron, it soon became evident that more information was needed regarding methods for determining the degree of reduction attained in the manufacturing process. Sponge irons made by different processes vary in physical characteristics and chemical composition, and a method of analysis that is suitable for one type is not necessarily applicable to all others. For example, the hydrogen-evolution method, which measures the volume of hydrogen evolved upon treating the sample with acid, accurately determines the oxygen content of some types of sponge iron. However, when the sponge iron contains combined carbon, hydrocarbon gases are also-evolved and large errors may result. Probably no single method will give accurate results in all instances, and for this reason it is desirable to have several reliable procedures available and to know the limitations of each.For measuring the degree of reduction, determination of either metallic iron or oxygen should suffice, although for practical application of sponge iron to the production of steel the oxygen content is more significant. After consideration of proposed methods of analysis in regard to their suitability for routine use and the probable influence of other substances, four procedures were chosen for investigation:(1) Mercuric chloride method.(2) Copper sulfate method.(3) Hydrogen-reduction method.(4) Hydrogen-evolution methods."

Sep 1, 1945

By H. R. Babitzke, H. Kato, R. E. Siemens

An investigation was made to provide further information for evaluating columbium- hafnium alloys for use as high - temperature structural materials . The columbium- hafnium system was investigated between 700 ° and 2,400 ° C by melting point , thermal analysis , X - ray diffraction , electrical resistivity , and metallographic techniques . The equilibrium diagram is the beta isomorphous type , with columbium tending to stabilize the beta phase . Addition of 60 atomic percent columbium stabilizes the beta phase at 700 ° C. The allotropic transformation temperature of hafnium is 1,750 ° ± 20 ° C. A minimum melting point occurs near 75 atomic percent hafnium .

Jan 1, 1964