Search Documents

By J. S. Hall

The performance of a full-scale balling drum circuit is well known to fluctuate, and is difficult to control. The fluctuations stem from causes that are not readily quantifiable. Results from plant tests show that surging of the recycle tonnage is dependent, inter alia, on the method of bentonite addition, small variations in drum or cutter bar speed and the method of drum water addition. This paper presents detailed observations from experiments on full-scale drum circuits, including preliminary results of a computer measurement and control scheme. Size distributions measured at points along an industrial drum are presented, together with the results of a mathematical model fitted to one plant data set. Model predictions are also included emphasizing the importance of screen performance on circuit stability.

Jan 1, 1983

By F Shi, W Valery

WMC Fertilizers (WMCF) operates a Beneficiation Plant at Phosphate Hill in Queensland, Australia. The plant consists of two-stages of crushing, followed by a wet scrubbing and desliming circuit. Ore is then fed to a tertiary crusher and a milling/classification circuit, with the final product going to a swing-lift thickener and storage tanks. From the slurry storage tanks, the phosphate rock is fed to a horizontal belt filters which dewater the phosphate rock ahead of a hemi-hydrate phosphoric acid plant. The water soluble recovery of phosphate in the phosphoric acid plant is dependent on the moisture content in the filter cake, as this governs the wash water addition to the hemi-hydrate filters. Since commencement of operation, the moisture content of the filter cake fed to the phosphoric acid plant has been higher than design reducing the phosphoric acid plant recovery and at times reducing the throughput through the phosphoric acid plant. The moisture content in the filter cake can be decreased by reducing the generation of fines in the milling and classification circuit (classified as û38 micron material). This paper identifies the causes of fines generation in the Phosphate Hill beneficiation plant. It discusses the options that were assessed to minimise fines generation, and outlines the results to date of circuit changes undertaken at Phosphate Hill.

Jan 1, 2003

By T. Cienski

The paper presents and discusses the results of a detailed study conducted on the subject of energy consumption in the comminution of industrial minerals. The study was based on pilot circuit testing, plant operating data collection, detailed equipment data and literature research. The areas covered by investigations include: high efficiency classification; air classifiers for cement grinding circuits; grinding aids in dry grinding: dry grinding circuit, control based on particle size measurement. Results obtained indicate a large potential for the reduction of energy consumption, in particular in the traditionally high cement clinker grinding circuits. Better classification techniques and correct application of grinding additives can significantly reduce power used per ton of product and also substantially increase grinding circuit output.

Jan 1, 1990

By M. Ghiani

Biohydrometallurgy originated, some forty years ago, from an environmental problem, namely the serious pollution of the Ohio river by acid drainage water coming from neighboring subbituminous coal mines. Studies aimed at elucidating the cause of the intensive oxidation of the iron sulfide (pyrite) inclusions of those coals, led to the discovery of a bacterium, Thiobacillus ferrooxidans (Temple and Colmer, 1951), capable of acting as a catalyzer, accelerating the otherwise very slow chemical oxidation of iron sulfide to rates many orders of magnitude higher. However, it is now recognized that the biotechnology of microbial mining dates back to 1963, when the ability of this bacterium to solubilize copper from sulfide ores was ascertained (Razzell and Trussell, 1963). Much research has been carried out on biohydrometallurgy over these last 25 years and is still being actively conducted all over the world. The interdisciplinary nature of this young branch of science and technology is reflected by the variety of experts involved: microbiologists, mining engineers, hydrometallurgists, physico-chemists, mineralogists, solid-state physicists and biochemists. This intensive research effort has provided a solid background on the fundamentals of this technology, although many important issues have still to be solved, amongst which the enzymatic mechanisms controlling biocatalysis of mineral sulfides dissolution, the influence of bulk- and surface solid-state physics of metal sulfides on dissolution mechanisms, the interaction of the various strains composing natural microbial floras. Their elucidation should permit the rationalization of biohydrometallurgical techniques and the optimization of commercial processes. Biohydrometallurgy has already achieved satisfactory results: copper recovery from submarginal copper sulfide run-of-mine ores (i.e. assaying less than 0.3% Cu) by in-situ, dump and/or heap leaching is successfully practised in many countries and uranium recovery through bioleaching is competitive with other leaching processes.

Jan 1, 1987

By John I. Sharpe

Masses of pyritic copper and zinc ores are entrapped along the contact zone between two volcanic groups in the Matagami area. The upper limits of the sulphide concentrations tend to form concordant contacts against lava or cherty tuffite units of the younger group; the lower extremities tend to either follow transverse structures or merge with zones of dispersed sulphides. The sulphides are deformed and intruded by folded dykes. Close relations between metallization boundaries and volcanic lithology and stratigraphy, and a preliminary investigation of the fabrics and crystallization temperatures of the sulphide masses, suggest that the copper and zinc (but; not necessarily all the iron sulphides) were emplaced at h1gh temperatures during volcanism in near-surface lithological-stratigraphic traps. Introduction T HE Matagami area is centered 120 miles north of the Val d'Or and Noranda camps in north-western Quebec. For the present purpose, it is considered to comprise a 155-square-mile area in Isle-Dieu, Galinee and Daniel townships which encompasses the main sulphide masses. Airborne geophysical surveys within this area in 1956 led to the discovery of a large sulphide body -the.

Jan 1, 1965

By NA UMC

Abstract Booklet

Dec 1, 2022

By Joseph M. Kurtak

The Bureau of Mines conducted a four year (1985-1988) mineral assessment of the Juneau Mining District in southeast Alaska as part of its ongoing statewide mining district evaluation program. Following an extensive literature search, the Bureau investigated mines, prospects, and mineral occurrences in the area. This report describes the results of Bureau work in the Eagle River area of the Juneau gold belt; a component of the Juneau Mining District comprising 87,000 acres between the Mendenhall Glacier and Berners Bay. Gold and silver have been the only metals having significant production from the area and occur mainly in quartz stringer and fissure type veins hosted by phyllites, greenschists, greenstones, altered diorite dikes and quartz diorite gneiss. Gold also occurs in several small placer deposits. Approximately 21,100 oz of gold and nearly 9,000 oz of silver were produced over a 60 year period. Currently, the only mining activity consists of some exploration and minor placer gold production. Inferred and indicated lode gold resources having mineral development potential total approximately 796,000 tons with a weighted average grade of 0.22 oz/ton gold.

Jan 1, 2011

By G. Bitsianes

An experimental procedure was developed for studying magnetic roasting on a accurately-controlled laboratory scale. The loss-in-weight method was used and the course of reduction could be followed under a reducing gas atmosphere containing as many as five different components. Some important variables of the operation were checked on a marginal Mesabi iron ore containing porous and dense varieties of hematite as well as pure goethite. The conditions simulated were those for the grate roasting of a coarsely-sized ore burden. Temperature was maintained at 600°C; gas composition at 4.25% CO, 4.25% H2, 17.0% CO2, 15.0% H20, and 59.5% N2,, and gas flow rate at about 1,5 lineal feet per minute. The ore charge was composed of quarter-inch cubes. Under these conditions, the ore porosity was found to be one of the governing variables of the operation. Results showed that an ore size limitation existed as a function of this ore porosity. For efficient magnetic conversion, the size limit was 3/8 inch for very porous ores and about 65 mesh for very dense ores. An anomaly was noted in the weight losses incurred during actual magnetic conversion. For goethitic ores, these were generally about 13 per cent higher than could be accounted for theoretically. The effect was attributed to possible non-stoichiometric structures forming during the reduction process.

Jan 1, 1960

The Bureau of Mines, in an effort to improve resource conservation, mine planning and development, is currently investigating the loading behavior of pillars in multiple-seam developments. The simultaneous mining of two or more coalbeds may cause instability between room-and-pillar operations resulting in an interaction known as pillar load transfer. Although pillars may be adequately designed for single-seam mining, the development of a second seam may complicate loading conditions in both operations. If pillars are not adequately designed to contend with this load transfer, failure of the mine structure may result. To improve multiple-seam development and pillar design, the Bureau studied the loading characteristics of pillars in three separate multiple-seam operations. In all three cases, instrumented pillars recorded increasing pressure after development of the second seam. Increases in the average pillar pressure ranged from 7 to 110 pct over predicted overburden loads. An analysis of pillar loading before and after second-seam mining indicates that the ratio of overburden to innerburden thickness is a critical factor influencing load transfer. Based on this relationship, safety factors for case study pillars are calculated and alternative design considerations are discussed.

Jan 1, 1988

By Stanley A. Feitler

This Bureau of Mines report deals principally with the resources and economic aspects of feldspar in the United States east of the Mississippi River. Although in a strict sense, all phases of the feldspar industry affect its economic structure, emphasis in this study is on supply, demand, and marketing. Although feldspar was originally mined for use in the manufacture of pottery and other ceramics, the glass industry, which began to use feldspar in the mid-1920's, now consumes more than half of the annual output. Most mining is open cut, and the methods used are similar to those used in mining crushed b stone. Excess plant capacity has been chronic, and production is usually about 30 percent of capacity fur the industry as a whole. Since 1947, feldspar consumption has grown more slowly than the average for all U.S. industry. This has fostered intense competition, especially for the glass market. Prices have not kept pace with inflation, and profits are small. The trend of consumption through 1970 for glass feldspar is expected to be upward; less rapid in consumption of ceramic feldspar is anticipated.

Jan 1, 1967

By M. Nzotta, L. Teng, S. Seetharaman, A. Chychko

The objective of the present work is to optimize the EAF practice towards Mo alloying with maximum retention of the alloying element in molten steel. During Mo additions, there were significant losses to the dust (ca 7 %) and to the slag phase (ca 2 %), which had serious economic and environmental impacts. The present work was aimed at designing a suitable Mo precursor, an alternative to ferromolybdenum, as the Mo source and a process sequence for optimal retention of Mo in the steel. The design of the Mo source should be in such a way that low cost raw materials such as MoO3 concentrate have to be used, stable during the addition so that the vapour phase losses as MoO3 are kept minimum and the dissolution of the precursor in molten steel is easy without loss to the slag phase. After thermodynamic considerations, three precursor materials were chosen, viz. CaMoO4, MgMoO4 and Fe2MoO4. Synthetic mixtures of the component oxides in each case as well as pure MoO3 were investigated by TGA and high temperature XRD in order to find out the temperature range in which the compounds were formed. Experiments were also conducted separately where the evolved gases were analyzed. All the three precursors were formed easily and the loss of MoO3 to the vapour phase was found to be extremely low. Addition of the oxide mixtures to steel melts were conducted in three different scales, viz. 16 g, 500 g and 3 tons (induction furnacle). Initial experiments showed that MgMoO4 was not suitable since the Mo yield in the steel melt was not very high. Fe2MoO4 was found to perform best, the Mo yield reaching 98 %. Further trials were conducted in the 65 ton Electric Arc Furnace (EAF) at Uddeholms AB in Hagfors. Mixtures of mill scale, MoO3 and carbon in suitable proportions were added in a pre-determined addition sequence. It was found that, in the actual practice, the Mo yield reached 99 %, equaling in performance the addition of ferromolybdenum. The process offers an effective use of cheaper raw materials and very high Mo yield avoiding a pre-treatment step like the production of ferromolybdenum. This is both cost effective and environmentally advantageous. The process has been patented and is being currently implemented at Uddeholms AB, Hagfors, Sweden.

Jan 1, 2011

By D. K. Dysinger

In this U.S. Bureau of Mines study, neodymium metal of 99.8 pct purity was prepared by electrolysis of Nd203 salts dissolved in a molten fluoride electrolyte. The metal was electrowon in a molten state at current efficiencies of 50 to 60 pct. Oxygen and carbon were the major impurities detected in the product. During operation of the small-scale laboratory cell, a number of technical problems including anode effect, low oxide solubility in the electrolyte, high neodymium metal solubility, reactivity of the metal with the cell materials, and back reaction of the metal with the anode gases were encountered. Approaches to improve cell operation and prospects for commercial adoption of the electrolytic production of neodymium metal are discussed.

Jan 1, 2010

By G. Bourque

Early in the design stage of their new concentrator for the Mount Wright Plant, Quebec Cartier Mining decided to use a process computer for total control of crushing, grinding and concentrating. A map of the area is given in figure 1 and a view of the plant in figure 2. Although the use of process computers is not a new idea in petrochemical and chemical industries, their use in the mining industry is very limited. We innovated in using the computer, not only for data logging, as we have seen in some other plants, but a sole operator located in the administration building, starts and stops mill lines, crushers, load-out system, tailings, thickeners, etc ... by means of a CRT console. Our process is fairly simple as can be seen on the schematic process flow diagram (figure 3). .The ore, carried by 136t diesel electric trucks, is dumped through ore pockets onto two primary pan feeders. The feeders supply two 1,52mx2,79m gyratory crushers which reduce the ore to minus 20,32 cm. Each crushing line have a capacity of 5600t per hour and feed a shuttle conveyor distributing the crude ore into six silos.

Jan 1, 1979

By R. J. Sheets

"What is the primary responsibility of geo-engineers in mining? Early in my career, I was asked this question by an experienced engineer. After explaining some various tasks, I was informed that the main responsibility was to monitor. Although this proved true for many cases, I came to understand that monitoring is merely one means to achieve the primary responsibility of a geo-engineer — ensure the safety of all personnel. The potential for groundwater to impact stability allows this responsibility to be shared with hydrogeologists as well. Inherently, we monitor to identify risks; we analyze designs and develop models to mitigate risks; and we are provided opportunities to explain to supervisors the geo-risks to personnel and mine plans that will result from particular courses of action. A couple years ago, I took an opportunity to share experiences from the first several years of my career as a geotechnical engineer with junior geoengineering staff within my company. The intent was to share situations that were a part of my development, so they could learn and understand their responsibility to the safety of all personnel. Similarly, the purpose of this article will be to share these thoughts with new geo-engineers in the industry in order to help prepare them for the challenges they will face.What is our purpose?A senior hydrogeologist shared an experience that occurred in their career. The experienced hydrogeologist had spent some time with the hydrogeology staff, most of them relatively new to the mining industry, to understand how they viewed, and carried out, what they perceived as their responsibility at an active mining operation. After a couple months of observing and mentoring, the senior hydrogeologist met with everyone and posed the question “What is our purpose?” I am sure that most junior geo-engineers would start explaining different tasks or projects that they must complete. The list would include monitor ground water levels, track slope movement, evaluate designs, build models, oversee drilling programs, etc. These individuals did as well their supervisor. After going around the room allowing each individual to answer, the experienced hydrogeologist provided them the real answer to the question: Safety. If you examine the root intent of nearly every responsibility geotechnical engineers and hydrogeologists have, it is to apply our professional skills to ensure the safety of our workforce. When the objective of safety from the geotechnical and hydrogeology disciplines is achieved, inherently accomplishing the mine plan should follow suit, or it should significantly minimize the impact by gravity or ground water."

Jan 9, 2018

By P. K. Muduli

The number and the type of trucks and shovels are two important factors in determining the optimal design parameters of an open-pit mining system. Characteristics of trucks' arrival and service-time distributions determine the performance measures of a truck-shovel system when it is modeled as a closed queuing network. In all of the previous analytical queuing studies of truck-shovel systems, trucks are assumed to be identical with respect to their arrival and service-time distributions. This assumption, although desirable for reducing computational difficulties, causes either underestimation or overestimation of the performance measures depending on the number and type of equipment used in the model. The relative error in performance measures could be significant when the number of different types of trucks and shovels is large. In this paper an analytical method is proposed to model the truck-shovel system as a multiple-chain closed queuing network. This approach would provide the capability of estimating system performance measures for planning purposes when the truck fleet is not necessarily composed of identical trucks. An example of truck-shovel systems is discussed to show how the incorporation of different types of trucks does affect performance measures.

Jan 1, 1996

By Douglas G. Baker, Jason K. Braund-Read, Megan R. Sheffer

"Mica Dam, owned by British Columbia Hydro, is an 820 ft high earthfill embankment dam that was completed in 1973. The dam consists of a thin central impervious till core supported by upstream and downstream compacted sand, gravel and cobble shell zones, founded on bedrock and valley bottom alluvium deposits. In 2012, a project was started to install new piezometric instrumentation within the dam’s foundation and downstream shell zone.Deep drilling in large embankment dams is very difficult and requires careful planning to select a methodology capable of reaching the target locations, while ensuring that no damage is done to the surrounding dam fill zones. At Mica Dam, the drilling could only be carried out from the Dam Crest and drillholes had to be carefully oriented to avoid intersecting any existing dam instrumentation. The drilling work therefore required angled drillholes, at depths of up to 855 ft, through heavily compacted sands, gravels and cobbles, and to significant depths below the standing water table.During the planning stages for the Project, in early 2013, the preferred drilling method was selected and a drilling contractor was engaged for the drilling work. Critical dam safety concerns were identified and addressed during the design stage of the Project with the drilling contractor, so that risk mitigation measures and response plans could be effectively developed.This paper explains how background information and prior drilling experience influenced the final design and implementation of the drilling techniques used in 2013 to successfully drill the deep holes and carry out the piezometer installations in Mica Dam. Drilling procedures, instrumentation design and installation methods, as well as risk mitigation measures, are discussed."

Jan 1, 2017

The current mining operations at Newmont Boddington Gold Mine (NBG) commenced in 2008, and commissioning of the processing plant started in the latter half of 2009. Metso Process Technology and Innovation were engaged to assist NBG with commissioning and project ramp-up through the implementation of a comprehensive ?Mine-to-Mill? Process Integration and Optimisation project. This methodology entailed extensive data collection which included drill and blast audits, ore characterisation, comprehensive comminution circuit surveys and review of operational data to assess the limitations within the current mining and processing operations. The results of these investigations have been used to define the operating base line of both the mining and processing areas and identify improvement opportunities. The use of modelling and simulations, utilising actual production data, has allowed for multiple scenarios to be evaluated, minimising the requirement for actual trials and thereby minimising impact on the operation. Improvements implemented to date include: the introduction of routine rock strength measurement for inclusion in block models, modifications to blast design improving ROM fragmentation and downstream comminution process performance, and changes to improve performance of secondary crushing and grinding circuits. Close cooperation between the mine and plant personnel is playing a significant role in overcoming the challenges presented to this operation and further improvements are targeted for the second full year of process plant operation.

Jan 1, 2012

By S A. Ravishankar

In heavy minerals separation, the titanium and iron oxide phases are separated from silicates in the coarser particle size range (80 - 150 mm) using magnetic and electrostatic separators. With the ongoing challenge of heavy mineral ore deposits getting increasingly finer in particle size, conventional separation equipment suffers from the ability to process this material at the same throughput rate as coarser particles. A variety of magnetic separation technologies were developed to perform at a much finer particle size range, down to 2 mm in the clay industries mainly to remove titaniferrous oxide particles. Complementing the developments made on the physical aspects of magnetic separation, Cytec Industries has recently developed a ‘bolt-on’ chemical enhancement technology for magnetic separation (CEMS). This is to enable separation of finer particles, and weakly paramagnetic titanium phases from diamagnetic silicates that are not amenable to magnetic separation. This paper will provide an outline of the technology, illustrate its ability to process a wide variety of ores, and also discuss plant limitations. The major advantages of chemical enhancement technology to magnetic separation includes: simple dosing equipment extension to existing magnetic separation technology; ability to produce product of comparable quality with improved cost effectiveness, when compared to incumbent flotation; removal of impurity minerals over wider size range; enhanced removal of non-magnetic impurities; and improving the process robustness. Furthermore, chemical enhancement technology for magnetic separation has also emerged as a platform for removing impurities at lower levels in other mineral systems as well.

Oct 5, 2011

By L. Allan White

Instrumental analysis is an indispensable tool to many phases of research on rare-earth metals and their compounds; therefore, the development of new and improved instrumental techniques is essential. This report describes an emission spectrometric analytical method using direct-current carbon-arc excitation of various rare-earth-oxide mixtures. Lanthanum oxide serves the dual purpose of an internal standard and a constant major constituent. The versatility of the method was demonstrated by three different applications: (a) Analysis of complex rare-earth concentrates; (b) determination of impurities in high-purity rare-earth oxides; and (c) detection of rare-earth elements in other types of matrices, such as those resulting from beneficiation of rare-earth ores. The average error of analysis in the concentration range of 0.2 to 10.0 percent was 14.6 percent for a group of complex synthetic mixtures of rare-earth oxides. An average error of analysis in the concentration range of 0.05 to 0.50 percent was 21 percent for a group of high-purity rare-earth oxides.

Jan 1, 1959

ABSTRACT This paper details the work of RISKGATE, the largest Australian Coal Association Research Program (ACARP) occupational health and safety initiative to date. The program is an interactive online risk management system developed to maximize health and safety performance in the coal mining industry by implementing continuous improvement in managing major unwanted events. The comprehensive knowledge base covers tires, collisions, fires, isolation, strata control underground, ground control open cut, explosions, explosives, manual tasks, and slips/trips/falls. All major Australian coal mining companies contributed topic experts to this broad industry initiative: nine coal mining companies, more than 80 experts, and more than 400 days of individual time for knowledge-capture workshops.

Jan 1, 2014