Search Documents

By JOHN G. RAYNER

An examination was made of the filtration characteristics of a haematite slurry using a range of polyacrylamide based flocculants in solutions containing up to 3 per cent sodium chloride. The polymers used were "high" and "Iow" molecular weight and had from 0 to 40 per cent charged groups.Increasing charge density tends to reduce the dose required to achieve optimum performance measured by filtration rate and by cake moisture. In general increased salt addition tends to increase the dosage required to achieve these optima. Both these observations result from the change in polymer extension and accord well with the bridging theory of flocculation.The dose required for optimal cake moisture is up to three times greater than that required for optimal filtration rate. This effect is reasonably consistent for all polymers studied and appears to be non-linearly dependent on salt concentration, with the difference being small at 0 and 3 per cent but quite significant at 1 per cent.

Jan 1, 1987

By S. Mohanta

In composite washeries optimization of operating parameters to achieve maximum clean coal yield at the desired clean coal ash level is a major problem. This problem is more acute in countries like India, which have predominant reserves of difficult-to-wash coals. The constrained operational parameters of washing for some equipments make it more severe. In addition to this, the dependence of separating performance of different equipments upon various variables aggravates the situation. Here an attempt is made to find a numerical solution to get maximum yield and minimize the difference between the actual and the theoretical yield. The solution is arrived through constrained non-linear optimization of a multivariable objective function that utilizes spreadsheet tools; the method accommodates any number of source coals or washing size fractions. By using a designed Ep value the predicted yield of composite clean coal has been calculated and the yield is optimized subject to constraints on both the ash and specific gravity. It is shown that operational constraints of different washeries in the composite plant that utilizes gravity separation methods can also be over-come. The technique offers the coal preparation engineer an effective and straightforward method for determining the optimum cut-points of separation for different coals or blended coals to obtain maximum product yield at a specified level of ash content.

Jan 1, 2014

By James R. Wait

An attempt is made here to collect together various reports and publications that are based on research supported all or in part by Contract No. H0155008 for the past two years. The subject matter deals primarily with the excitation, transmission, and reception of electromagnetic waves in mine environments. This contract from the U.S. Bureau of Mines with the Office of Telecommunications supports the efforts of James R. Wait (Principal Investigator and Consultant to OT), David A. Hill (Co-Investigator), and various associates within the Boulder scientific community. The contributions of Samir F. Mahmoud were supported, in part, by the contract while he was a Visiting Fellow with the Cooperative Institute for Research in Environmental Sciences at the University of Colorado. Administrative assistance in CIRES has been provided by Mrs. Lana R. Hope.

Jan 1, 1976

By Michael Rieber

Mineral economics interfaces the mineral sciences and engineering with finance and economics in the analysis of appropriate questions facing the minerals and energy industries. Its practitioners include those trained in the earth sciences; mining, petroleum, and geological engineering; metallurgy and mineral preparation; as well as finance, information systems, economics, and statistics-most usefully in one or more combinations. Allowing for some overlap, three general areas may be identified: evaluation, economic analysis, and resource appraisal. Evaluation begins with mine investment analysis (exemplified by Gentry and O'Neil, 1984) and process costing, for which the STRAMM Handbook (Anon., 1977) provides a well-known basis for mining and beneficiation. But it extends from property appraisal, often used for the determination of taxes and royalties, through the determination and comparison of transport costs (e.g., Richer and Soo, 1977), and to benefit/cost analyses of externalities. Economic analysis, the subject of this section, is displayed in rigor and extent both theoretically and as applied to commodity classes in Vogely (1985), but it is implicit though apparent throughout Lefond (1983). The text edited by Vogely places minerals in their aggregative context with economic growth and trade, proceeds to the theoretical analysis of minerals and their markets, analyzes the structure and performance of the major mineral sectors, and concludes with policy issues: fuel, nonfuel, and environmental. Resource appraisal employs quantitative methods for the estimation of mineral and energy resources. It moves through geologic, geophysical, and geochemical properties to the identification of estimation procedures for mineral endowment and for the economic measure of stocks and flows of specific minerals (Harris, 1984). It can be used to estimate the probable amount of a specific resource remaining in a given region and has been used to project sites in a specific

Jan 1, 2008

By Henry E. Blake

Defluorination studies on refractory fluoride - bearing compounds and minerals , particularly on partly defluorinated residues from high - temperature pyrohydrolysis , required a dependable and reasonably accurate analyticalcontrol method for the analysis of fluorine . The difficulty in liberating fluorine from the fluorides of metallic elements such as aluminum, zirconium , and rare earths by steam- distillation can be largely overcome if the distillation is made from a sulfuric - phosphoric acid solution of a sodium carbonate fusion of the sample material and if the distillation temperature is maintained at about 155 ° C. The data presented in this paper show that liberation of fluorine by this method is more complete and proceeds more rapidly than by usual distillations from perchloric or sulfuric acid alone or a mixture of phosphoric and perchloric acids . Fluorine in amounts ranging up to about 140 mg can be recovered by collecting only about 300 ml of distillate . Determination of fluoride in the distillate is made by the usual thorium nitrate titration .

Jan 1, 1963

State ownership of minerals results in domestic legislation regulating mining operations. The mining industry today is dominated by a number of transnational companies, each subject to internal and external pressures for a more responsible approach to resource management. Thirty to 40 major companies are responsible for the bulk of the worldÆs mineral production with the balance coming from state-owned, second tier and junior companies and from artisanal miners.Mining companies operating within competitive commercial environments formerly focussed on mineral production. Companies worked to standards and expectations then current which largely failed to recognise the impact of mining activities on community interests. The mining industry acquired a reputation for arrogance, and for placing profitability ahead of issues considered equally or more important by local communities. Current perceptions continue to reflect disquiet about industry attitudes towards traditional land-owners and access to their lands, to environmental contamination, handling and storage of waste materials, utilisation of water and electricity, and to rehabilitation of worked out areas. Major international mining companies concerned at continuing criticism sponsored a series of initiatives with the objective of providing guidance on working harmoniously within the community. Industry commissioned studies, performed through the agency of disinterested parties, resulted in May 2002, in a Declaration being issued at an International Conference in Toronto. The Declaration was based on, but did not reflect all of the recommendations of the MMSD Report, æBreaking New GroundÆ.This paper considers whether benefits would result from the negotiation of a legally binding and enforceable international protocol encompassing the objectives of the MMSD report or the Toronto Declaration. It attempts to identify the problems associated with implementing and enforcing international mining law, should it be introduced. Aspects of mining operations having cover under customary international law are reviewed, as are rights, obligations and remedies for breaches of national mining law. Conclusions are drawn based on established procedures relating to implementing international agreements. The continuing ability of mining companies to operate within communities will result from each satisfying the communityÆs expectations rather than by complying with largely unenforceable legislation.

Jan 1, 2004

By P. D. Rao

Chemical and physical properties of typical low-rank coal (LRC) ash are significantly different than bituminous coal ash. With the exception of extraneous ash, which is incorporated during mining or is due to ash partings within or between coal seams, LRC ash consists primarily of inherent ash that is bonded into the coal's organic matrix or finely disseminated mineral matter. This paper reviews the nature of LRC ash, both inherent and extraneous, and how this impacts the prospects of washing and utilizing LRCs. A literature review, as well as washability data, proximate and ultimate analyses and ash analysis of 25 Alaskan LRC seams are used as a basis for this discussion. The authors' recent research into the nature and distribution of phosphorous in an Alaskan LRC is also discussed

Jan 1, 1997

By J. D. T. Steyl

"This paper presents a phenomenological model of the rate of iron(III) precipitation in batch and continuous autoclaves at medium temperature operating conditions. The rate expressions are based on information obtained from the literature and experimentation at low and high pulp densities. Special allowance is made for the formation of surface nuclei, which appears to be promoted at a higher iron(III) precipitate surface area, especially in suspensions of lower terminal acidity. This leads to the formation of secondary particulates and provides the required link to simulate high pulp density leaching-precipitation systems, using low pulp density batch precipitation data. In particular, the model allows direct application of the simulation to the autoclave oxidation of iron-containing copper sulfide concentrates and provides a good estimation of the relative precipitation rate of hematite, the preferred product, compared to hydronium jarosite. Some interesting mechanistic understandings of iron(III) precipitation in autoclaves are further elucidated.INTRODUCTIONThe objective of this work is to describe the rate of iron(III) precipitation and the relative amounts of hematite compared to hydronium jarosite precipitation during batch and continuous chalcopyrite oxidation under medium temperature (MT) (~130 to 160ºC) autoclave conditions. Published information has not yet revealed sufficient mechanistic insights about this sparingly soluble salt system under these conditions. The rate expressions in this paper are based in part on current literature information, supplemented by qualitative experimental observation at low pulp density conditions, in particular the high-resolution backscatter electron (BSE) images and particle size distributions (PSDs) of the precipitates. A summary of this work and insights from the literature are presented first, after which the behaviour of iron(III) in high pulp density leaching systems is used to derive a phenomenological expression of the effect of existing iron(III) precipitate surface area on the precipitation rate. The overall regression encapsulates all the experimental results, i.e., those obtained in both batch and continuous autoclave configurations (Steyl, 2012a)."

Jan 1, 2012

By Pierre Sauvé, Alex Makila

"The Camflo stock of porphyritic quartz syenite is an irregular pipe-like body 200 metres in diameter injected along the axial plane of an E-W trending F2 fold, near the contact between the. Kewagama and Malartic groups. The stock plunges 55° to the NE, almost parallel to the fold axis. The stock, exhibiting pervasive, weak cataclasis with numerous, locally auriferous quartz veinlets, is cut by minor faults striking WNW and dipping about 45°NE.Two types of gold ore are distinguished at Camflo: ""porphyry"" ore and ""fault zone"" ore. ""Porphyry"" ore, accounting for 90% of the gold produced, forms wide zones within the stock. The zones are irregular in shape but tend to be oriented E-W in plan view (on a horizontal plane) and are elongated paraliel to the plunge of the stock. These zones are more abundant in the northern part of the stock. Differences between ore and barren porphyry are not obvious. ""Fault zone"" ore occurs outside the stock along minor faults, particularly in differentiated sills offer rodiorite and felsic granophyre. Gold grade is roughly proportional to the pyrite content which in turns depends in part on the original magnetite content of the host rock. Although both types of ore show some correlation between Au and S, the Au/S ratio is considerably higher in porphyry ore.The bulk of the gold is in quartz syenite and in felsic granophyre, the most brittle lithologies at the mine. Presumably, the vertically continuous, pipe-like stock, made up of shattered rock, provided the main channelway for the ascending mineralizing solutions."

Jan 1, 1990

By Enrique Jelvez, Pierre Nancel-Penard

The traditional way of generating open-pit mine production schedules has several limitations. This work addresses the design and production-scheduling problem by considering minimum operational space requirements under a Direct Block Scheduling approach to generate extraction sequences that satisfy the operational space required. For this, traditional formulations were extended by including a new set of constraints that generate operating spaces for mining equipment to move and extract material. Then, a heuristic algorithm produces close to optimal practical pushbacks. This proposal was applied in a case study, and the results show its ability to generate practical production schedules without sacrificing expected return, obtaining differences in terms of Net Present Value (NPV) lower than 1% when compared to the traditional approach.

Jun 25, 2023

The sole reason for a mine to exist is to extract the finite mineral resource. Accurate grade control is critical to the economics of any mine. If grade control is not optimised, then no matter how good the downstream processes are, the full potential of the operation will not be realised. The detailed implementation of grade control varies but typically consists of sampling and assaying to determine the location of the ore zones. A lot of time, money and effort are spent defining the location of the ore as accurately as possible à but then it is blown up! The effect that blasting has on grade control is rarely adequately accounted for when the rock is excavated because there has never been an accurate and practical method for measuring blast movement. This paper draws on over six years of research into measuring and understanding blast movement, which started at the Julius Kruttschnitt Mineral Research Centre (JKMRC) of the University of Queensland. The research has made a unique contribution to open pit blasting by helping to develop a practical tool for measuring blast movement, which was then used to improve the understanding of three-dimensional blast movement dynamics. However, these achievements would be of largely academic interest without taking the final step of using this technology and knowledge to account for blast movement by translating the ore polygons in response to the measured movement vectors. This paper provides an overview of blast movement but focuses on one site where blast movement was measured during three separate periods, with significantly different orientation of the mineralisation on each occasion. The theoretical ore loss varied from nine per cent to 24 per cent. The differences are primarily due to the orientation of the ore polygons relative to the direction of movement. The optimum grade control solution is a combination of accurately accounting for blast movement and designing appropriate blasts.

Jan 1, 2009

By J. P. R. deVilliers

A procedure is described whereby gold-containing calcined concentrates and leach residues from refractory gold ores are smelted with carbon to form a small amount of metal. The gold is liberated upon smelting, and is collected in the molten metallic phase, which is easily separable from the slag. The metallic phase consists of approximately 1 to 15 per cent (by mass) of the material after smelting, and the gold content is generally upgraded by a factor of greater than 6 compared with that of the original roasted material. Recoveries better than 95% have routinely been achieved. The quenched metal contains predominant Fe-Ni alloy, as well as minor Fe sulphides and Cu-Fe sulphides. Trace amounts of Fe-Ni arsenide and Au-Cu alloy are also present. The gold content of the metallic phase can be increased further by oxidation of the hot metal in the presence of silica or slag. This will reduce the amount of metal, and will concentrate the gold in a smaller volume. The metallic phase can then be treated hydrometallurgically to recover the nickel and the gold.

Jan 1, 1989

By W. G. Pariseau

Recent advances in rock mass mechanics and computational technology now allow for stability analysis of excavations in "wet" mines where mining-induced changes in rock mass deformation and fluid flow are coupled and time-dependent. All the usual dry mine parameters including the premining stress state and rock mass properties are taken into account, in addition to water pressure and flow in jointed, possibly porous, rock masses. Finite element analyses of shafts and tunnels as circular, elliptical, rectangular and arched-rectangular hole shapes excavated in an initially stressed and pressurized rock mass indicate that the usual guidelines for optimum shape and orientation of single openings apply. Here, optimum means maximizing the minimum wall safety factor, or equivalently, minimizing the peak stress concentration. The results also show that failure originates in elements at the wall and that the minimum safety factor at the wall in the wet case is always less than the dry case regardless of drainage time allowed.

Jan 1, 1995

Research 84 highlights significant studies conducted during the past fiscal year at Bureau facilities and offices. Readers who want more information about the projects and studies summarized here can contact the researchers whose names and locations appear with each summary. General information on Bureau of Mines programs is available from the Office of Technical Information, 2401 E Street, NW., Washington, DC 20241. A listing of principal officials, a location map of field facilities, and a selected bibliography of publications and patents issued on Bureau developments during the past 3 years are provided.

Jan 1, 1984

By Corwin L. Cooper

This paper, describing; the milling and cyanidation methods and costs at the Yellow Aster gold mine, is one of a series of papers being prepared by the Bureau of Mines on bold milling practices in the United States. Acknowledgments Acknowledgment is made to the executives of the Anglo American Mining Corporation, Ltd., for permission to publish this article, and to A. W. Frolli, manager, and other members of the company staff, for assistance` in preparing the, paper.

Jan 1, 1936

By D. D. Macdonald, G. Engelhardt

The accumulation of damage due to localized corrosion [pitting, stress corrosion cracking (SCC), corrosion fatigue (CF), crevice corrosion (CC), and erosion-corrosion (EC)] in complex industrial systems, such as power plants, refineries, desalination systems, etc., poses a threat to continued safe and economic operation, primarily because of the sudden, catastrophic nature of the resulting failures. Of particular interest in managing these forms of damage is the development of robust algorithms that can be used to predict the integrated damage as a function of time and as a function of the operating conditions of the system. Because complex systems of the same design rapidly become unique, due to differences in operating histories, and because failures are rare events, there is generally insufficient data on any given system to derive reliable empirical models that capture the impact of all (or even some) of the important independent variables. Accordingly, empirical models have generally failed to provide a robust basis for predicting the accumulation of corrosion damage in complex systems under realistic operating conditions. The alternative prediction philosophy is determinism, in which the development of damage is described in terms of valid, physico-electrochemical mechanisms with the output being constrained by the natural laws. The differential damage is then integrated along the corrosion evolutionary path for the system (i.e., over the future operating "history") to yield the desired integrated damage, which is the quantity that is most useful to an operator. In this paper, we review the theory of predicting corrosion damage within the framework of Damage Function Analysis (DFA), with particular emphasis on the pitting of aluminum in chloride solutions and on the accumulation of damage from SCC in Type 304 SS components in the primary coolant circuits of Boiling Water (Nuclear) Reactors (BWRs). These cases have been selected to illustrate the various phases through which localized corrosion damage occurs.

Jan 1, 2005

By B. Cousins

Copper, nickel, zinc and other ?penalty? metals are found with gold together in nature, and have a similar chemical affinity for cyanide used in leaching operations4. As a result, solutions that come from the heap leach pads contain a significant concentration of penalty metals along with the desired gold. In solution, gold and cyanide form the complex Au(CN)2- that is readily adsorbed onto activated carbon. Penalty metals as individual metal ions also load onto activated carbon and, depending on the concentration of cyanide and the pH of the solution, can form various cyanide complexes. Some of these complexes can also load onto carbon while some are significantly inhibited from loading. Copper, for example, can form the dicyanide complex Cu(CN)2-, the tricyanide complex Cu(CN)32-, and the tetracyanide complex Cu(CN)43-. At a low pH and a low concentration of cyanide, the dicyanide complex predominates. At a higher pH and a higher concentration of cyanide, the tetracyanide complex predominates. Without excess cyanide, however, individual copper ions can remain present. Activated carbon is used in gold extraction because it is highly selective for gold and less so for other metals, such as copper3. However, copper has the ability to adsorb (?load?) onto activated carbon and block the adsorption of gold when it is in the dicyanide form and in a high enough concentration. When copper is in the tetracyanide form, copper loading is significantly inhibited, allowing for the maximum gold recovery. In order to ensure the tetracyanide complex is formed, a combination of both available cyanide and elevated pH must be present. In the South Area of Newmont Mining Corporation?s Gold Quarry mine in Carlin, Nevada, copper and nickel loading becomes a problem when certain acid generating zones of the heap are leached. Copper, nickel, zinc and other penalty metals become leachable and the lower pH uses up more of the cyanide and creates carbon loading conditions for the metals. This decreases the carbon?s ability to extract the gold from solution, decreasing the recovery and increasing the concentration of gold in the barren solution that leaves the carbon columns. In this study, operational data from March through to May of 2007 is presented to show how Newmont developed a quick fix to lower pH and elevated metal concentrations that were causing low gold loadings on activated carbon at their South Area Leach (SAL) heap leach operations. Laboratory tested were also conducted to examine the chemical kinetics of metal loading and the individual effects of increased cyanide concentrations. THEORY Copper I ions form four different complexes with cyanide in solution: the monocyanide species CuCN, the dicyanide species Cu(CN)2-, the tricyanide species Cu(CN)32-, and the tetracyanide species Cu(CN)43-. The species are formed from the following reactions: [Cu)(?+-+ K1 (1) Cu ß2 (2) --+?+23)(3CNCuCNCu ß3 (3) --+?+34)(4CNCuCNCu ß4 (4) ] where K1 equals 1019.50, ß2 equals 1024.03, ß3 equals 1028.65, and ß4 equals 1030.35. Along with these complexing reactions, hydrogen cyanide and water also dissociate in solution, as per the following reactions: [H?+-+ KH (5) OHOHH2?+-+ KW (6)] where KH has a value of 109.24 and KW has a 1014 value2. These six chemical equations compete with each other, with domination of one over the others dependent on the CN- and H+ concentrations. Each complex also has different properties when it comes to its loading behavior on activated carbon. The dicyanide copper complex and the monocyanide copper complex have an affinity for adsorption onto activated carbon that is greater than the affinity of gold cyanide for adsorption. They also have a lower solubility in water, which enhances adsorption. The tricyanide copper complex and the tetracyanide copper complex are water soluble and have an affinity for loading adsorption on activated carbon that is less than the affinity of gold cyanide for loading adsorption1. There are three prime reasons for this phenomenon. First, the extra cyanides mask the metal ion more, which blocks the main adsorption characteristic of the complex. Second, the complexes are also larger, making it harder to physically fit into the active sites on the carbon. This helps make the latter two complexes kinetically inhibited from adsorption, freeing carbon active site to load with gold cyanide complexes. Third, it is also important to consider the expressions of the mass and charge balance. These balances describe all the overall concentration of copper and cyanide in solution, as well as marking overall charges of the ions in solution4. This is important because significantly changing the charge from positive/neutral to more negative is another reason for activated carbon to reject adsorbing the higher cyanide complexes. The speciation of copper and other penalty metal cyanide complexes in solution is dependent on the pH. At lower pH values, increased hydrogen ions (H+) can out-compete metals for cyanide ions. Lower free cyanide in the system leads to the lower cyanide species of copper cyanide predominating, with a noticeable concentration of the free metal, monocyanide and dicyanide species of copper cyanide. At higher pH values, hydrogen ions are significantly reduced, reducing the kinetics of HCN formation. More free cyanide remains in the system, allowing for more complexing. With this higher amount of cyanide in the system, the tetracyanide species of copper cyanide predominates, also with a noticeable concentration of the tricyanide species of copper cyanide. Higher copper concentrations, however, require more

Jan 1, 2009

By Pei‑liang Xu, Jun Wang, Xi Zhang, Deng‑pan Qiao, Tian‑yu Yang

The surface backfill, serving as the operational platform for continuing mining in upward slicing and filling stopes, is required to possess sufficient strength and thickness. Currently, there are limited model methods for determining the strength and thickness of the surface fill body. By analyzing the mechanical actions on the surface backfill, it is determined that its stability is mainly influenced by the combined effects of normal and tangential uniform loads under full-load conditions of trackless equipment. Assuming a circular contact surface between the tire of the trackless equipment and the surface backfill, and utilizing solutions from elastic mechanics theories such as the Boussinesq and Cerruti solution, the stress and displacement distribution of the surface fill body were obtained. Based on the maximum vertical stress condition, where the surface backfill body undergoes maximum deformation while still in an elastic state, and considering the stress–strain relationship, a model for the strength and thickness of the surface backfill has been established. According to the research findings, the design for the strength and structural parameters of the surface backfill has been developed to meet the full-load operation of the Atlas ST7 scooptram, with a compressive strength of 1.32 MPa and a thickness of 0.5 m. Numerical simulation analysis results indicate that the stress and displacement of the surface backfill align with theoretical analysis results. Practical results from industrial application in the western section of the Dahongshan Copper Mine demonstrate that the designed strength and thickness of the surface backfill meet the operational requirements for trackless equipment, resulting in significant engineering application effects and economic benefits. The research findings hold significant importance for advancing the theory of backfill mining and have high applicability and promotional value for similar mines.

Mar 24, 2024

By S. V. Lukichev, O. V. Nagovitsyn, V. V. Laptev

In this paper the authors describe the developed algorithms of short- and medium-term planning of underground mining operations. The algorithms were developed using the example of the flat-back cut-and-fill method, and provide multifactor accounting of mining conditions, technical and technological limitations: state and properties of the rock mass; the current mining situation; mining rules; availability of safety pillars; properties of the filling; additional characteristics of technological objects that complicate the driving of workings; sufficiency of human and technical resources; employee specialisation; existing machinery and equipment; opportunities and limitations of the transport scheme of the mine, and work schedule. The paper is presented by means of a dynamic model of mining development, which shows the sequence of mining operations in the mine workings. Besides animation, the tool provides an opportunity to form tabular and graphical reports.

Sep 1, 2021

By Elia Elias, Alan Crosky, Paul Hagan, Damon Vandermaat, Serkan Saydam, Peter H. Craig

"The University of New South Wales (UNSW Australia) had been involved in the study of premature failure of rock bolts in Australian coal mines from the initial identification of the problem in 1999 (Crosky et al 2002). Rock bolt steel changes over the last decade appear to have not reduced the incidence of failures. A broadened UNSW research project funded by the Australian Research Council (ARC) and Industry has targeted finding the environmental causes through extensive field and laboratory experiments. This paper describes the field studies conducted in underground coal mines, in particular attempts to measure the contribution to corrosion from groundwater, mineralogy and microbial activity. Various underground survey techniques were used to determine the extent of broken bolts, with the presence of both stress corrosion cracking (SCC) and localized deep pitting making no single technique suitable on their own. Groundwater found dripping from bolts across various coalfields in Australia were found to be not aggressive and known groundwater corrosivity classification systems did not correlate to where broken bolts were found. In-hole coupon bolts placed in roof strata containing claystone bands confirmed the clay as being a major contributor to corrosion. Microbes capable of contributing to steel corrosion were found to be present in groundwater, and culturing of the microbes taken from in-situ coupon bolts proved that the bacteria was present on the bolt surface. An ‘in-hole bolt corrosion coupon’ development by the project may have multiple benefits of 1) helping quantify newly developed corrosivity classification systems, 2) providing an in-situ ground support corrosion monitoring tool, and 3) for testing possible corrosion protection solutions.introductionThe problem of premature rock bolt failure in Australian coal mines was published in 2002 and 2004 by UNSW Australia from Australian Coal Association Research Program (ACARP) funded projects. The majority of the broken bolts examined had steel Charpy impact toughness values of 4 – 7 Joules, and the failure mechanism was most often stress corrosion cracking (SCC). Steel fracture mechanics predicts that an increase in impact toughness will increase the length of the crack before sudden brittle failure. In the final report of 2004, anecdotal evidence from one coal mine indicated that the problem may be eliminated in some environments by a change to steel grades with higher Charpy impact values of ~16. (Crosky et al, 2002 and 2004)"

Jan 1, 2015