Search Documents

THE CHAIRMAN (G. H. CLEVENGER, Stanford University, Cal.).¬I would like to ask Mr. Pyne if he has had any experience inn the use of chromite as refractory under conditions that are highly reducing? I am reminded of an experience I once had with an electric furnace. I imagined that chromite would form a splendid lining, but it soon disappeared; hence it seems probable that, under highly reducing conditions at a high temperature, chromite is a very poor refractory. F. R. PYNE.-In copper smelting the atmosphere is generally neutral, or slightly oxidizing; we do not use highly reducing atmospheres at all, not even in the matting furnace. You can take the chromite brick and treat it as you would an iron ore, obtaining ferro-chrome very readily, from which the copper will separate. We have done this; in fact, at one time we considered installing a small electric furnace for the production of ferro-chrome. FOREST RUTHERFORD, New York, N. Y.-During the time I was general superintendent at the smelter of the Copper Queen Consolidated Mining Co., at Douglas, Ariz., a great many experiments were made on the furnaces and settlers with different kinds of brick, and I agree with Mr. Pyne's statements about chrome brick. Their power to absorb metals is very great, and as they cannot be smelted at any temperatures obtainable in a copper furnace, to get rid of the bats and extract the metal from them is quite a problem. We finally got down to using chrome brick only for lining the settlers, out of which we often got a life of upwards of 2 years, and for lining the blast-furnace bottoms, for the reason that chrome brick can be heated and wet, or wet after being heated, without going to pieces, whereas under these conditions magnesite brick will break down very rapidly. We also used a layer of chrome brick above and below an 18-in. band of magnesite brick put on the slag line of the reverberatories, in order to separate the magnesite from the silica brick, fearing that they would slag each other and let the wall drop. The idea worked, but became unnecessary on account of a change made in the method of feeding the furnaces. Chronic brick will not stand up under pressure so well as a good Grecian or Austrian magnesite brick, on account of the poorer bonding properties of the materials from which the chrome brick is made.

Jan 4, 1918

By C. Wert, P. Bunn

Determination of the solid solubility of gases in metals is usually done by one of two methods. The first is an additive method, in which measurement is made at temperature of the maximum amount of gas absorbed by an initially degassed piece of the metal. Gas additions are made until the dissolved gas first comes into equilibrium with a compound. This method is most useful at relatively high temperatures where the amount of gas absorbed is relatively large and where equilibration of the dissolved gas with the gas atmosphere can be achieved in a relatively short time. The second is a precipitation method. A supersaturated solution of the gas in the metal is held at temperature until equilibrium is established between the gas atoms in solution and a compound. The quantity of dissolved gas is then determined by some physical measurement which is sensitive only to the gas in solution. This method is generally useful in low temperatures. This paper describes measurement of solubility of nitrogen in tantalum whereby measurements at low temperatures using internal-friction methods are plotted together with existing measurements at high temperatures. The solubility is thereby known from less than 0.5 at. pet at 350°C to near 13 pet at 2300°C. Several measurements have been reported of the solubility of nitrogen in tantalum. These are collected in Fig. 1. Three single determinations by Ke,1 Andrews,2 and Brauer and zapp3 are plotted along with a series of measurements by Vaughn, Stewart and schwartz4 and Gebhardt, Seghezzi, and Fromm.5 Although not much doubt exists about the solubility being in excess of 10 at. pet above 2000°C, the solubility indicated at low temperatures depends on whose data are selected as being most reliable. The variation is enormous, being at least an order of magnitude at 500°C. Accordingly, a measurement was begun to examine this discrepancy. The method of measurement finally selected was that of internal friction. A solid solution of nitrogen in tantalum was prepared by heating a tantalum wire in a dilute at-

Jan 1, 1964

By Subhash Bhagwat

The definition of high sulfur coal varies from plant to plant and is subject to changes over time as the environmental regulations change. In plants constructed after September 1978 hardly any domestic coal can currently be burned without the use of Flue Gas Desulfurization (FGD) because a 70 percent reduction in potential S02 emission is mandatory even when the potential emission is less than 0.6 lbs. S02/106 Btu heat input. On the other hand older power plants may in many cases be legally emitting up to 6 lbs. S02/106 Btu or more under some State Implementation Plans (SIP). The Clean Air Act requires, however, that in the long run all stationary sources of S02 pollution must abide by the ceiling of 1.2 lbs S02/10 Btu heat input.. Coals with a potential to exceed this limit must, therefore, be considered as high sulfur coals. Such a definition would be unrealistic because many SIP's aim at an emission level of 1.8 to 2.0 lbs. SO2/106 Btu for existing plants and a stricter limit does not appear to be enforceable in the next 5 to 10 years. As a result, coals with an emission potential of greater than 2.0 lbs of S02 per 10 Btu heat input are considered high sulfur coals for the purpose of this investigation. Based on this definition and the 1984 actual consumption of coals by U.S. electric utilities (table 1) only 7 out of the 24 coal producing states could be categorized as low sulfur states. The actual S02 pollution, however, depends on total tonnage of a type of coal as well as the sulfur content of the coal. Table 1 also indicates that only 6 states--Kentucky, Illinois, West Virginia, Ohio, Pennsylvania and Indiana-account for nearly 77 percent of S02 pollution potential in the United States. These 6 states have therefore been chosen for this investigation.

Jan 1, 1986

By J. Blodget Britton

IN the Journal of the Franklin Institute for May, 1870, there is published a description of a Colorimeter, together with a modification of the method proposed by Professor Eggertz, for determining combined carbon in iron and steel. An instrument of the kind there described, but of a little higher range, though in other respects not differing materially from the one originally made and used in the Iron-Masters7 Laboratory, I now submit to your inspection ; and I propose, also, to make some determinations minations with it for the purpose of showing how quickly they may be made, and enabling you to form some judgment of what reliance can be placed in the results. Professor Eggertz proposed only a single standard, and the solution to be tested should be diluted to exactly correspond in color with that of the standard, and the per cent. of carbon calculated after carefully noting and making allowance for the measures of water used in diluting. In practice, difficulty was found in bringing the color of the normal solution down to the exact shade of the standard; also other difficulties were met with in conducting the process, causing delay and interfering with the accuracy of the results. To materially overcome these, and after numerous attempts, an instrument such as is now before you suggested itself to me; and also I concluded to use a larger quantity of metal than directed by Eggertz, and, in addition, to filter the solution from its insoluble matter before making the comparison; and, more recently, to use an acid of just such strength as would completely dissolve the metal without the application of heat. Experimenting with these changes from the original method I obtained reasonably good results. The instrument, you will observe, consists of a series of tubes, sixteen in number, two and a half inches long, and about half an inch in diameter, standing upright, and securely fastened in a light, portable, walnut-wood frame, but separated one from the other so as to allow just sufficient space between to place for comparison the . tube containing the solution to be tested. The tubes are filled with

By Thomas E. Ricketts

Occidental Oil Shale Inc. has spent the last eight years at its Logan Wash. mine near DeBeque, Colorado, developing its modified in-situ oil shale process for obtaining oil from oil shale. Modified in-situ technology involves large underground chambers, or retorts, which are formed by mining out a minimal volume of rock to allow explosive expansion of the surrounding rock into tile mined void volumes. The resulting rubblized retort volume must contain a fairly uniform particle size distribution and void distribution to permit maximum oil recovery during subsequent in-situ processing operations. The more uniform the rubblized volume of particles, the more oil recovery obtained during processing. The processing involves first igniting the top of the retort and then. injecting air into the top of the retort to drive the combustion front downward through the entire rubblized volume. The oil is continuously collected at the bottom of the retort during the processing.

Jan 1, 1981

By Raymond L. Lowrie

For many years it has been considered that an average of 50 percent of the coal in the deposits exploited has been recovered. Owing to many changes in mining methods during the past two decades, this study was initiated to obtain an up-to-date measurement of recovery percentage and thus establish part of the basis from which presently recoverable reserves may be estimated. Recovery percentages were determined within mined areas of 200 underground coal mines. These comprised a statistical sample selected to be representative of operating mines in relation to their significance to depletion of reserves. The results ranged from 29 to 91 percent and averaged 57.0 ± 1.7 percent (95-percent confidence limit). Six factors were identified mathematically as significantly affecting recovery percentages: (1) Pillaring system, (2) top rock and conditions, (3) bottom rock and conditions, (4) marketability, (5) coalbed thickness, and (6) productivity. Skill and attitude of mine operators toward recovery, although not measured, were probable factors. Five other variables that were tested did not show any significant relationship with recovery percentages. Also, five mining equipment features were identified, through discussions with mine officials, as affecting adversely recovery percentage at some mines.

Jan 1, 1968

By Alfred Fisher

CONSERVATION of mine timber is becoming in-creasingly important, and the consumer is en-couraged to use treated wood to permit longer life of mine timbers, and attempts are also made to substitute other material for wood. The great diffi-culty in substituting metal and concrete props for wood is the inability of these to give yielding resistance to roof pressure as wood supports do. In Europe, where mine timber costs are somewhat more important than in America, many designs of steel props have been tried, but have been unsuccessful, chiefly on account of inability to give yielding resistances. A metal pit prop that gives the desired effect has been extensively used in European mines and has caused a considerable reduction in accidents from falls of roof. Where mining operations have been sus-pended on account of strikes, conditions were found to be much better where such props were used instead of wood props, and machinery, which would have been destroyed by roof falls had wood props been used, was protected by the use of these yielding metal props. As this prop is adjustable, all the work of adjusting and transferring long props through narrow ways is done away with. It can also be drawn with greater ease and safety than wooden props; when properly used it is practically indestructible. European users have reported savings as against wooden props as high as 80 per cent. It gives audible warning of its working because the sliding action takes place in minute jerks. As the prop yields gradually to pressure its force is taken up by friction between the H sections, and this movement progressively increases the resistance of the prop to the increasing roof pressure. In the early development of the prop, it was designed with two steel members a and b of standard H steel sec-tions of equal dimensions provided with guide claws a' and b', held in frictional contact against each other by two differential wedges, f and g, and a floating link, e. In setting up the prop its two members are drawn out to the required length, the loose wedge, g, is then fitted into the space between the left-hand roller of the link d and the lower member of the prop b, and tapped suf-ficiently tight to prevent any relative movement of the two members from taking place prematurely. The prop is then raised to its intended position and secured in the usual way.

Jan 8, 1927

By M. J. Kanda

"The design of rock slopes in the planning and operation of open pit mines and for road and rail cuttings requires the evaluation of their stability. This is commonly done using two well-established methods – limit equilibrium and numerical modelling. The research described in this paper compares the outputs of analyses using these two methods with regard to factor of safety and probability of failure, taking into account technical factors associated with each method and other factors such as material parameters and their variabilities. Results show that technical factors such as number of slices and slip circles, number and type of finite elements, and the stress reduction factor can all affect the results of stability analyses. Factors not taken into account in limit equilibrium analyses, such as dilation, in situ stress, and locked-in stresses can affect the outputs significantly. The research has focused particularly on the predicted location of the failure surface, the resulting volume of failure and, most significantly dependent on this volume, the predicted risk associated with slope failure. The results presented show that there is good agreement between the outputs of the two methods regarding factor of safety and probability of failure. However, the same is not the case with regard to volume of failure and hence risk, which can be very dependent on the methods of analysis and their input parameters. The research is not exhaustive, and there are many other factors that could affect the results of slope stability analyses that were not investigated. Some such factors are mentioned in the paper.IntroductionThe design of rock slopes in the planning and operation of open pit mines and for road and rail cuttings requires the evaluation of their stability. The traditional method of stability analysis used limit equilibrium (LE) methods, and this approach continues to be used. Numerical modelling (NM) packages are now also commonly used in slope stability analyses. The outputs from these analyses provide the factor of safety (FOS) and probability of failure (POF) of the slope. Since the capabilities of the two approaches are different, there can be some variations in FOS and POF outputs and in the predicted location of the failure surface. These variations can affect the predicted volume of failure, and this could in turn have a significant effect on the risk associated with the potential failure (Read and Stacey, 2009). Researchers such as Chiwaye and Stacey (2010) have found that LE analyses underestimate the predicted failure volume, unlike NM methods."

Jan 1, 2016

By Don L. Kendall, Martin G. Buehler

A simple physical model has been developed to fit carrier-removal data in silicon irradiated near room temperature with reactor spectrum neutrons. Commonly observed donor and acceptor defect energy levels are assumed to be introduced linearly with neutron fluence. The donor levels (in ev) are Ev + 0.16, Ev + 0.27, and Ev + 0.31 and the acceptor levels are Ec - 0.55, Ec - 0.40, and Ec - 0.1 7, where Ev and Ec are the valence and conduction band energies, respectively. The introduction rates of each level are adjusted to fit literature initial carrier-removal rate data. When normalized with respect to the Ev +0.27 level, the relative values of introduction rates are 5.3, 1.0, 3.1, 1.0, 2.0, and 20.0, respectively for the six levels indicated above. To fit p-f (hole concentration vs neutron fluence) and n-f (electron concentration us neutron fluence) data, the introduction rates are multiplied by a factor which preserves the relative values given above. This factor depends upon irradiation temperature, reactor energy spectrum, neutron fluence calibration, and oxygen content of silicon. An extensive study of the effect of neutrons on carrier-removal in silicon irradiated with reactor spectrum neutrons (E > 10 kev) has been given by Stein and Gereth1 (SG) and Curtis, Bass, and Germano' (CBG). They measured initial carrier-removal rates for both p- and n-type silicon over an impurity range typical of silicon devices. In this work, we attempt to fit a simple theory to this data to establish a usable relationship between hole and electron concentration, p and n, respectively, and neutron fluence f. The p-f and n-f relations are needed to assist in the design of neutron tolerant silicon devices and are needed to clarify presently used empirical resistivity-fluence relationships.3 Neutron damage in silicon produces a variety of defects ranging from simple point defects to defect clusters. For the purpose of this treatment, we assume that simple point defects dominate carrier-removal effects. In contrast to this view, stein4 has proposed that defect clusters are responsible for a significant portion of carrier-removal effects. In the following section, it is shown that the carrier-removal effect in n-type silicon with an electron concentration less than 1015 cm-3 can be explained adequately by assuming that the divacancy is the dominant defect and that its introduction rate is independent of the electron concentration. For electron concentrations greater than 1015 cm-= an additional acceptor defect center is needed, and for simplicity the A-center (vacancy-oxygen pair) has been chosen. Although the E-center (vacancy-phosphorus pair) can account for some of the results, the A-center was chosen because the E-center requires a more involved treatment which the presently available data do not justify. In p-type silicon three radiation-induced donor levels are assumed, namely the divacancy and two other centers of unspecified nature located at Ev + 0.16 ev and Ev to 0.31 ev. The donor divacancy at Ev + 0.27 ev is assumed to be introduced at the same rate in p-type as in n-type. However, this rate is too low to fit p-type initial carrier-removal data. The dominant centers in p-type silicon are assumed to be the Ev + 0.16 ev and Ev + 0.31 ev levels where the latter is not the divacancy. The introduction rates are chosen to fit initial carrier-removal rate data. Assuming that the introduction rates are independent of Fermi level, the ratio between them is fixed for subsequent p-f and n-f calculations. Using the same ratios, the initial carrier-removal rate data1,2 as well as p-f and n-f data1,5 can be fit provided the absolute value of the introduction rates are adjusted to account for irradiation temperature, reactor energy spectrum, neutron fluence calculation, and the oxygen content of silicon. THEORETICAL ANALYSIS This analysis is basically the same as that used by Hi116 to analyze electron damage in silicon except we express the degree to which an impurity level is ionized not in terms of the Fermi level, but in terms of carrier concentration. Landis and pearson7 have used the latter approach to analyze y-damage in silicon. Neutron-induced defects responsible for carrier-removal at room temperature are assumed to be simple point defects with no interaction between defects so that they may be represented by discrete energy levels. It is also assumed that no constituent of a defect complex is used up and defects stabilize shortly after irradiation. Defects are assumed to be introduced linearly with fluence according to the product Rtf where Rt is the defect introduction rate and f the neutron fluence. Taking into account the ionization of defects according to Fermi statistics, and considering charge neutrality where minority carriers are neglected, the n-f relation is where no is the preirradiation electron concentration. The parameter Nt is the electron concentration at which the ionized defect concentration is one-half the total defect concentration (Rtf) or where Et is the defect energy level. For silicon at 300°K, ni = 1.45 X 1010 cm-3 and Ei = Ev+ 0.542 ev which was determined using Ec — Ev = 1.11 ev and me* = 1.07 mo and mh* = 0.558m0. The spin degeneracy factor, which usually appears as a number multiplying the Nt/n term of Eq. [1], is taken as unity. In effect, this factor has been incorporated into the defect en-

Jan 1, 1970

The number of employees required to operate a continuous operation was determined. The fixed and variable costs of the operation were separated, generally along the lines of labour and stores components. Proprietary `MicroPlanner' scheduling software was used to assess resource utilisation under the constraints generated by seven-day operation to determine the level of resources required and ensure that the maximum use was being made of all resources. The mine economic model was used to account for both the fixed and variable costs of the various task to determine the cost and net revenue of the various scenarios. The analysis indicated that mine output could be increased while reducing the unit production cost. Several eight- and 12-hour, seven-day rosters were sourced and ranked for their potential to improve production and communication, and for their effect on employee health and lifestyle.

Jan 1, 1995

By Evangelos Spyridonos, Thomas Frommer, Wolfdietrich Skala, René Prissang

Operational grade modelling is a technique that uses production data to run daily updates of property models. It will enable mining engineers to use property predictions based on the most recently acquired data as support for quality control and decision making. The approach necessitates that the properties of the run- of-mine material can always be attributed to individual mining blocks or charges. The software employed must be highly reliable, because a system failure or the loss of data could seriously affect the mine's quality management. An operational grade modelling system has been developed for the Breitenau magnesite mine. It makes use of the Linear Octree Based Property Modelling system which was conceived and realised at the Free University of Berlin. This paper describes the system design and gives an account of the experiences during the first six months since system start-up.

Jan 1, 1996

By E. O. Abrokwah

Directionally solidified (DS) Rene 80 Superalloy was tested in thermo-mechanical fatigue (TMF) over the temperature range 500-900°C and plastic strain levels from 0.2 to 0.8% using a DSI Gleeble thermal simulator. Thermo-mechanical testing was carried out on the parent material in the conventional solution treated and aged condition (STA), as well as gas tungsten arc welded with an IN-738 filler, followed by solution treatment and ageing. Comparison of the base TMF unwelded alloy with that of the welded and heat treated alloy showed that varying crack initiation mechanisms, notably oxidation either by stress assisted grain boundary oxidation, or associated with grain boundary MC carbides fatigue crack propagation along grain boundaries and creep deformation were operating, leading to different "weakest link" failure initiation points.

Jan 1, 2011

In deposits in which the secondary zones are well defined a layer of rich oxidized ore is frequently found immediately to overlie the enriched sulphides, from which it is derived by direct oxidation in place. In deposits that contain oxidizing precipitants particles and masses of residual oxidized ore are likely to be scattered through the leached zone, having been precipitated during migration before reaching the zone of enrichment. This precipitation hinders secondary enrichment and in extreme cases prevents the formation of such concentrations. Residual ores are precipitated by various reagents. Carbonates are formed through the action of the carbonic acid contained in surface waters, and also directly through the replacement of calcite, especially where the containing rock is limestone. Native metals, such as copper, gold, and silver, are formed by the action of reducing agents, among which organic matter and ferrous sulphate are prominent. Kaolin, gouge, and certain shales occasionally act as powerful precipitants through adsorption. Silver is often found as residual chloride, formed through precipitation by the chlorine contained in surface waters. Residual ores are often the result of incomplete solution, the relatively insoluble minerals being left behind during the migration of associated metals; incomplete oxidation and solution often leave residual masses of unaltered, or partly altered, sulphides in the oxidized zone. Such residual particles or masses have commonly been enriched by additions from circulating, metal-bearing solutions. During oxidation under conditions that permit reprecipitation, such as the oxidation of sulphide deposits in limestone, a scat-

Jan 1, 1932

By C Gunther

In deposits in which the secondary zones are well defined a layer of rich oxidized ore is frequently found immediately to overlie the enriched sulphides, from which it is derived by direct oxidation in place. In deposits that contain oxidizing precipitants particles and masses of residual oxidized ore are likely to be scattered through the leached zone, having been precipitated during migration before reaching the zone of enrichment. This precipitation hinders secondary enrichment and in extreme cases prevents the formation of such concentrations. Residual ores are precipitated by various reagents. Carbonates are formed through the action of the carbonic acid contained in surface waters, and also directly through the replacement of calcite, especially where the containing rock is limestone. Native metals, such as copper, gold, and silver, are formed by the action of reducing agents, among which organic matter and ferrous sulphate are prominent. Kaolin, gouge, and certain shales occasionally act as powerful precipitants through adsorption. Silver is often found as residual chloride, formed through precipitation by the chlorine contained in surface waters. Residual ores are often the result of incomplete solution, the relatively insoluble minerals being left behind during the migration of associated metals; incomplete oxidation and solution often leave residual masses of unaltered, or partly altered, sulphides in the oxidized zone. Such residual particles or masses have commonly been enriched by additions from circulating, metal-bearing solutions. During oxidation under conditions that permit reprecipitation, such as the oxidation of sulphide deposits in limestone, a scab

Jan 1, 1932

By E. E. Malouf

For centuries small amounts of copper have been recovered from acid mine-drainage waters. In recent years, the expansion of copper-bearing waste dump leaching for copper recovery has established a technological basis that is rapidly converting the art of copper leaching into a science. Copper leaching and recovery from solution has become an important adjunct of nearly all copper mining operations. Leaching of copper, whether from copper- bearing ore or waste, follows well established chemical reactions commonly in an acid circuit, but where leaching of copper is to be made in rock that is a high acid consumer, ammonia and ammonia carbonate, as well as cyanide leach solutions, can be used effectively. Current hydrometallurgical processes are being applied at an ever increasing rate to recover the trace amounts of copper in copper mine waste by in-place leaching. Currently approximately 300,000 tons of copper are produced annually in this manner while as recently as ten years ago, only one-eighth of this amount of precipitate copper was produced. Where copper occurs as an oxide in higher concentrations as to be classified as an ore rather than waste, then the hydrometallurgical processes are applied as percolation or agitation leaching in vats, pachuca tanks or prepared heaps. This approach gives better control over the recovery of the leach solutions, particularly in the processes where ammonia or cyanide leaching agents are to be used.

Jan 8, 1972

By N Madani

Linear interpolation of geo-related variables is important to different aspects of mining engineering such as long and short-term mine planning. The ore deposit description attained from spatial modeling of blast hole datasets has been widely taken into account, particularly, for short-term mine design and grade control, so as to define the ultimate destination of a mined block. It is approved in practice that making the wrong decision leads to losing a huge amount of money for choosing the destination of a mined block. In the case of complex ore deposits, the issue of estimation of variables in the region is questionable and somehow tedious. Due to this fact, modeling those complications in the co-spatial behavior of the grades in multi-element deposits prompts one to employ enhanced geostatistical techniques. Traditional approaches of this purpose such as polygon, inverse distance weighted and even (co)-kriging approaches, are incapable of reproducing those complexities such as non-linearity, heteroscedasticity and geological constraint that frequently exist among the variables of interest in those deposits. Another difficulty in employing those linear interpolations in grade estimation is smoothing effect, in which the estimated grades are over and under estimated. CITATION: Madani, N, 2018. 3D estimation of variables with complexity in cross-correlation structures, in Proceedings Complex Orebodies Conference 2018, pp 49–52 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By Jason Wilkinson

Drilling operations are a vital component of surface mining, directly influencing productivity, safety, and cost efficiency. This paper explores a multi-faceted approach to drill optimization, focusing on minimizing delays, and enhancing operational effectiveness. Key areas of inefficiency such as shift changes, fuel and water delays, and time lost between drilling holes are analyzed to identify actionable improvements. Equipment related factors, including the frequency of drill bit and drill steel changes, as well as the condition of deck bushings, are evaluated for their impact on downtime and performance consistency. Additionally, the integration of smooth drives and shock subs is examined for their role in reducing vibration related wear and improving drilling precision. Optimization of pattern approach strategies is highlighted as a means to reduce non-productive movement and align drilling with blast design more effectively. To support continuous improvement and accountability, the implementation of a driller scorecard is proposed. This tool enables the measurement of individual performance based on key operational metrics, fostering a culture of data driven management. Through a combination of field data analysis and best practice recommendations, this study provides a comprehensive framework for enhancing drilling productivity in mining operations. The findings aim to support mine operators in achieving higher efficiency, reducing operational costs, and extending equipment life through targeted optimization strategies.

Jan 26, 2026

By D. J. Chaiko

Certain radionuclide ions (e.g., TcO4) exhibit unusually strong Affinities toward the polymer-rich phase in aqueous biphase systems generated by combinations of salt solutions with polymers such as poly(ethylene glycol) (PEG) and poly(propylene glycol) (PPG). Thus, aqueous. polymer ,phases could potentially be used to selectively extract these ions during pretreatment of radioactive tank wastes at Hanford. To help develop a fundamental understanding of the interactions between various ions and polymers in aqueous solution, interaction enthalpies between sodium -perrhenate and a random copolymer of PEG and PPG (UCON-50) were measured by microcalorimetric titration. An entropy compensation effect was observed in this system in which changes in enthalpic interactions were balanced by entropy changes such that the interaction free energy remained constant and approximately equal to zero.

Jan 1, 1999

By T. Wajima

"A novel carbonaceous adsorbent for recovery of nickel from nickel plating waste solution was prepared from rice straw using sulfur impregnation. The rice straws were cut to 1 cm pieces, and then immersed in 0.01 - 3 M K2S solution to prepare sulfur-immersed materials. The immersed-materials were heated at 100-700 ºC in nitrogen gas to produce the sulfur-impregnated carbonaceous adsorbent by pyrolysis. The contents of carbon and sulfur in the adsorbent and abilities of adsorbent to recovery nickel from aqueous solution were examined. The contents of carbon and sulfur in sulfur-immersed materials are almost same as those in raw material. In pyrolysis, with increasing the heating temperature to 200 ºC, the contents of carbon and sulfur are almost constant, and then above 300 ºC those increase. The recovery for nickel using raw material, sulfur-immersed material and the product pyrolyzed at 100 - 200 ºC are almost same, and with increasing the heating temperature to 400 ºC, that of the product increases, and above 500 ºC that of the product decreases. In immerse step, with increasing K2S concentration, the carbon content of the product at 400 ºC gradually decreases, the sulfur content of the product increases, and the recovery for nickel using the product gradually increases and then above 1 M K2S decrease. The product prepared from material immersed in 1 M K2S solution at 400 ºC indicates a maximum recovery for nickel ion. The product can adsorb nickel ion in nickel plating waste solution coexisting with phosphate ion, and adsorbed nickel ion in the product was deposited as nickel metal after heating at 1000 ºC under N2 atmosphere.INTRODUCTIONRice is the second world’s largest cereal crop after wheat, but produces large amount of straw residues, of about 330 million metric tonnes. Rice is a widely grown crop in Asia, and rice straw is produced as a by-product of rice production. In most parts of rice fields, open-field burning of rice straw is commonly practiced in the region when there is limited time to prepare a field for the next crop. However, open-field burning of crop residues is an uncontrolled combustion process during which air pollutants are emitted into atmosphere. These air pollutants have significant toxicological properties and are potential carcinogens (Gadede et al., 2009). Although wildfires are prohibited in cultivation fields of most countries, farmers usually keep on burning their crop by-products. Biomass burning is an important source of aerosol particles which may affect local and regional air quality (Gao et al., 2011), and also contribute to global climate changes."

Jan 1, 2016

By Leon Lorenzen, Victor E. Ross, Anton W. Kleingeld

Key to successful innovation, whether at organization, industry or national level, is the alignment and utilization of resources in the most appropriate and efficient way. Innovation needs to be directed strategically, and it needs to be auditable in a systematic and integrated fashion. In the light of these considerations, this paper describes the construction and use of a topographical map of the innovation landscape. The purpose of the map is to provide a holistic view of the key factors that enable innovation (the so-called ’landmarks’), how well they are aligned to support a particular type/nature of innovation in the organization, and to identify possible gaps. The significance (importance) and height (performance) of the landmarks in supporting and enabling innovation within the organization is determined by means of a selfappraisal audit. The topography of the landscape derived thus is subsequently interpreted in terms of the organization’s particular innovation strategy and environmental context. The application of the Innovation Landscape Methodology is illustrated in a number of organizations within the Mining and Minerals Industry of South Africa. Important observations and conclusions regarding the strategic alignment of enabler strengths within these organizations are made.

Jan 1, 2003