Search Documents

By Martin Landwehr

"Dust samplers are based on different principles. The konimeter is based on the number of particles counted; mining applications are based on routine sampling; and the photometrical evaluation of samples is used after the pre-separation of particles above 5 micron by the mining konimeter. In special cases, the Draeger sampler is used for quantitative analysis. General trends are toward larger samples, concentration on a weight basis, fractionation into size groups by different techniques and an analysis of composition. Standards or TLVs already exist in all industries. Surface industries base their criteria on concentrations and quartz contents in particles below 5 micron. The mining industry uses the tyndalloscope routinely to determine concentrations; concurrent] y, the rock content, as deter-mined by ashing samples, is obtained by konimeter.Threshold limits are related to the rock content in respirable fractions and tyndallometrically determined concentrations. The TL Vs are based empirically on Landwehr's ""dust values,"" as agreed upon with the Mines Inspectorates. Recently, and in accurate sampling, dust samplers have been used that count the dust in two fractions -above and below 5 microns. Mineral composition is determined either for all minerais or just for quartz. In assessing the dust hazard by Landwehr's ""dust values,"" all minerais are taken into consideration; in coal dust sampling, however, only the quartz content is taken into account. Efforts are now being made to co-ordinate the different assessment methods, arriving at uniform MAC values in agreement with those of other countries."

Jan 1, 1969

By Kenneth Gavin, Weichao Li, Paul Doherty

"The lateral load capacity is one of the most important issues to be considered in designing piles to resist berthing loads, ship impact forces and for monopiles used in the offshore wind sector. A number of semi-empirical design approaches are available to calculate the ultimate soil resistance and assumed soil reaction profile along the piles’ embedded depth. In order to investigate the response of monopiles to lateral loading, a series of field experiments were conducted on instrumented steel pipe piles. Two lateral loading tests were performed on model piles with a diameter, D, of 340 mm and embedded depth, Lem, of 2.2 m, giving a Lem/D ratio similar to those adopted in the offshore wind sector. The piles were driven into dense sand at the University College Dublin geotechnical test bed site in Ireland. 10 pairs of strain gauges were installed on each model pile along the embedded depth at 10 levels to capture the load transfer and bending moment within the piles. The deflection and rotation at the model pile head were measured by Linear Variable Differential Transformer (LVDT) and inclinometers. The tests results were used to perform a detailed evaluation of current design methods. In the final section, discussion on the determination of the ultimate lateral load capacity for monopile design was conducted. IntroductionA pile’s lateral load capacity is determined, for design purposes, by two conditions: 1) the ultimate lateral load, Fu, divided by an appropriate safety factor; and 2) the load according to the maximum lateral deflection that the support structures can sustain. In view of the first condition, design methods to calculate the ultimate load were developed for piles used in the offshore oil and gas sectors, which tend to be much more slender than monopiles used in the wind industry. The purpose of this study was to investigate whether these design methods provide reasonable estimates of ultimate capacity, for short rigid monopiles.The methods to determine the ultimate lateral load generally follow three steps: 1) determine the ultimate soil resistance, Pu, along the pile embedded depth; 2) adopt the most appropriate soil reaction profile, Pz, along the piles embedded depth when the pile subjected to the ultimate lateral load condition (four of the most popular ones are depicted in Figure. 1); and 3) ensure equilibrium of lateral forces (see Equation 1, symbols are listed at the end of the paper) acting on the pile and bending moments (see Equation 2) about a point in pile is employed to determine the ultimate lateral load."

Jan 1, 2015

By Brian W. Mackenzie

The mine development decision is made on completion of exploration to determine whether or not a mineral deposit should be developed to production and, if so, how. This involves the selection of an optimum mine development alternative from a number of technically feasible alternatives and the comparison of this optimum with those of other available investment opportunities. If the optimum is sufficiently attractive, the deposit is developed to production. The selection process is carried out within a framework of corporate objectives and resources. The mine development decision is based on the balancing of two parameters - - rate of production as reflected in plant capacity and cut-off grade. On the basis of available information and experience, detailed revenue and cost 'estimates are made for each feasible combination of plant capacity and cut-off grade. What economic evaluation techniques should be applied to these estimates to reduce each alternative to economic indicators that will enable meaningful comparisons and an informed investment decision? This is the essence of the paper. The determination of optimum plant capacity and cut-off grade has been the subject of intensive research efforts by economists and mining engineers (1-7). Their studies are based on marginal analysis and assume that, at the time of decision, certainty conditions prevail with respect to ore reserves, mining costs and mineral markets. The optimum mine development alternative is defined as that which maximizes profitability.

Jan 1, 1969

By William R. Barton

It is generally conceded as axiomatic that the aggregate producer and the average urban resident have mutually incompatible goals. The producer wants to be near his mass market and the average resident wants him as far away as possible. The traditional economic decision to mine local material to avoid transportation costs is increasingly challenged by zoning and planning bodies and by citizens' groups. This conflict generated much written and spoken word and offered opportunity for great flights of rhetoric. The pressure on the producer also has forced re¬appraisal of the need for the classic confrontation with indications that much of the conflict is more apparent than substantive. In New England several factors combine to increase complexity of the siting problem. It is a region of high land values and population density. Due to the proximity of metropolitan areas, even rural communities have experienced a prolif¬eration of environmental groups with concomitant enthusiastic regional planning and critical watch over land use. In New England where there is little public understanding of the necessity for, and the realities of, mineral production a sophisticated approach to aggregate production site location is required.

Jan 1, 1975

By E. A. Domínguez

Kaolin deposits of Patagonia (Argentina) were formed by ?in situ? alteration of volcaniclastic rocks or by erosion, transportation, and deposition of residual clays in small basins. The mineralogy, geochemistry, grain size distribution, and specific surface area of natural and washed kaolins were studied in order to point out the relationships with the ceramic process. Primary kaolins are coarse-grained, kaolinite+quartz±halloysite, with a very low specific surface area. Sedimentary clays are either kaolinitic?smectitic and very fine-grained or kaolinitic with a coarser particle size distribution. An interdependence between mineralogy, chemistry, particle size distribution, texture, surface activity and ceramic behavior was found. Plasticity is strictly dependent on surface activity and expandable clay minerals. Slip rheology is affected by soluble salts, smectite, and tubular halloysite. Kaolinite-halloysite play an opposite role versus smectite-I/S in slip casting and tile pressing. Kaolinite and quartz are beneficial for drying behavior while expandable clay minerals increase drying sensitivity. Firing behaviour is mainly affected by minor components supplying fluxing oxides.

Jan 1, 2010

By J P. Barkas

World demand for iron ore is far from peaking, and the substantial price decline that has captivated commentators since early 2014 is not the result of widespread misreading by producers of the prospects for global market growth. Recent price movements provide little useful insight into the industry’s longer-term fortunes, apart from reminding mining companies that their businesses need to be robust against the volatility and inescapable cyclicality of mineral commodity markets. It is timely to take a strategic view of the history and longer-term prospects for the iron ore industry and of Australia’s place in it.CITATION:Barkas, J P, 2015. Perspectives on the long-term outlook for iron ore, in Proceedings Iron Ore 2015, pp 3–6 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By A Mehrani, F Zamani, A Dehghani

Vibrating screens play an important role in the dry classification circuit of Gol-e-Gohar iron ore processing plant. This circuit was designed to classify the autogenous mill discharge and produce a suitable feed, with K80 about 450 ¦m, for dry magnetic separators. Three parallel vibrating screens produce more than 50 per cent of the separatorÆs feed. The efficiency of the magnetic separator is greatly affected by feed size distribution. In this work, the JKSimMet 5.1 software was used as an analysing tool to assess the flow rates and USIM PAC3 software as the simulation tool to control and optimise the vibrating screens. Samples were collected and the circuit was mass balanced. Then the vibrating screen was simulated and adjustment parameters such as cut-point, bypass and imperfection factor were determined. The product streams of vibrating screens can also be predicted.

Jan 1, 2007

By R. V. Ramani, R. Bhaskar

"IntroductionThe behavior of dust clouds in mine atmospheres has been a subject of longstanding interest due to both health and safety reasons. Pioneering studies in Germany and SMRE focussed on ambient dust concentration, principally aimed at determining optimum velocities for effective dilution. A summary of studies related to this area is provided by Hall,(l) Efforts to understand dust deposition from the explosion hazard point of view led to experiments in return airways (2-4) followed by experiments in longwalls.(5) Concerted efforts, either experimental or theoretical, were not made until recently to relate ambient concentration with dust deposition in mines. In 1974 Hwang et a1 (6) developed a computer model to predict dust concentration which considered deposition-concentration relationships. Also, experimental studies involving concurrent dust deposition and ambient concentration were conducted in the U.S. by Courtney et al (7 ) in operating mines. Efforts to relate theory with experimental results have been made by Owen (8) and Hwang et al (6 ) for dust deposition. There has been limited work, however, to determine the application of the theories and assumptions from aerosol sciences for modeling dust flows in mine atmospheres. (9 ) This is the objective of the work currently underway in the Generic Technology Center on Respirable Dust since· 1983 under a project titled, ""Prediction of Ambient Dust Concentration in Mine Atmospheres."" The scope of the project activities include:1. Development of a mathematical model to predict dust deposition and concentration in mine atmospheres.2. Experimental studies on dust transport and deposition in mine airways.3. Comparison of the model results with the experimental data."

Mar 1, 1989

By Forrest T. Moyer

To keep the mineral and allied industries informed of trends in the causes of accidents, and to point out the need for corrective measures, the Bureau of Mines collects, analyzes, and periodically publishes health and safety statistics. This report includes data for 1963 on injury experience, with related employment statistics, at coal mines in the United States. These data are presented in tabular form under the following headings: General Injury Experience Tables 1 to 6: Current data on number of injuries, degree of injury, frequency and severity rates, average severity, and related employment and production data by work location.

Jan 1, 1966

By Byron W. Cheever

In working up the process which I described at the Chicago Meeting, May, 1884 (p. 163 of the present volume), for the estimation of phosphorus in iron and steel, I employed samples of steel obtained from one works only, and of a given brand. Since then I have had frequent occasion to test the process on other steels, and find that it works equally well. But some steels present certain colors which may mislead the operator; and I therefore propose a slight change in the directions formerly given. On the second page of my paper, in the second paragraph, I would substitute the following modified directions: Place the flask under the hydrant, till the solution is perfectly cold ; then add, gradually, strong ammonia, with constant stirring, till the solution is changed into a pasty mass and the ammonia is in slight excess; then add cautiously HNO3 (1.40 specific gravity)

Jan 1, 1885

By J. Dean Warner

In 1984 and 1985, as part of its critical and strategic minerals studies, the Bureau of Mines investigated lode and placer tin occurrences near Rocky Mountain (Lime Peak), in east-central Alaska. The lode occurrences consist of mineralogically complex, generally fault-controlled veins, and contain an average of approximately 0.05 pct Sn, as cassiterite. Beneficiation testing of two bulk samples of the vein material produced concentrates containing 65 and 59 pct of the total tin values at grades of 0.35 and 13.9 pct, respectively. Although as much as 30 million short tons (MMst) of mineralized rock containing up to 20 MMlb Sn may be present, the grade of these occurrences is too low to be considered economic at this time. Trace amounts of cassiterite were also identified in surface samples of glacial out-wash gravels collected along North Fork Preacher Creek, which partially drains the area of tin lode deposits near Lime Peak. Low tin grades in the samples do not account for the former erosion of a large volume of lode tin mineralization from near Lime Peak; higher tin grades may be present in gravels closer to bedrock.

Jan 1, 1988

By Julijan Bratun, Joze Kortnik

Production of technical stone is an important economic branch in Slovenia. In 2009, we had 95 dolomite quarries, 27 limestone and 6 silicates quarries, according to the Ministry of Economic Affairs. Together they produced nearly 15 million tons of aggregates. The production in quarries is mostly performed with drilling and blasting method and only a minor part with other method like mechanical mining method.

Jan 1, 2011

By Sun Shao Xian

The Port of Shekou is situated at Shenzhen Bay on the east side of the Pearl River estuary. Geological condition of the site is quite complicated. On top of the sea bed, there is a layer of soft silt 8 - 14 m thick. Under the soft silt, there are intercalated layers of sand, silt and clay. Average surface elevation of the underlying undulatory weathered bed rock is about - 20 m, with a variation of about 10 m. In certain locations, the weathered bed rock is covered with a layer of silt 3 - 4 m thick. This paper gives brief account of three types of wharf structures which are of particular interest, constructed in the last few years: (A) Platform type wharf structure with frontal sheet piling and steel raking pile in the rear; (B) Relieving Platform type structure with steel sheet piling and inclined anchoring HP pile ; (C) Steel pipe pile row supported apron added to a marginal quay. Average construction time of a deepwater berth is about six months.

Jan 1, 1991

By William V. Robinson

The Iron Ore Company of Canada mines, processes and ships crude iron ore, concentrate and pellets from the rich ore bodies of the Labrador Trough area in the extreme north-eastern part of Canada, some five hundred miles from Montreal (see figure 1). There are three main sites of activity. At Schefferville, approximately 12 million tons a year of crude ore (chiefly limonite) are mined, crushed, screened and shipped to Sept-Iles. At Labrador City, 40 million tons of specular hematite are mined annually for processing into 17 million tons of concentrate. Of this, 9 million tons are converted into pellets. All product 1s shipped to Sept-Iles. At Sept-Iles, on the north coast of the St. Lawrence, a six million ton per year concentrator and pellet plant process much of the Scheffervllle ore into high-grade pellets. Also at Sept-Iles are the company's administration offices stockpiles and shipping facilities. The Terminal facilities can berth and load a 250,000 ton bulk carrier at 19,000 tons per hour.

Jan 1, 1975

By R Lastra, Y Choi, C Hamilton, P Kondos

Hydroseparation (http://www.cnt-mc.com) was used to concentrate sized fractions (from <38 ¦m to 150 ¦m) of various ore products ahead of carbon-in-pulp (CIP)-treatment. The resulting size-by-size concentrates were mounted as monolayer polished sections and subjected to automated unattended precious metal searches by image analysis (see Lastra, Wilson and Cabri, 1999). Systematic variations in Au-deportment permit quantification of Au reporting as discrete grains from fresh-feed through to pressure oxidation (POX)- and CIP-feed. Application of hydroseparation, image analysis and assays to characterising tailings (from <10 ¦m to 106 ¦m) from four mine sites is also described. Results are encouraging enough to predict that the combination of hydroseparation (HS) and automated image analysis could become a standard methodology for study of precious metal ores and metallurgical products.

Jan 1, 2008

By Mark Koelling

This paper presents a case history of a ground improvement program conducted in a soft soil environment and seismically active region in the northwest corner of Washington State near the Canadian border. The program was performed over several years, and provided adequate soil bearing conditions for the construction of several structures. Completed development includes separate construction of four adjacent structures, each with unique total and differential settlement requirements and built at approximate two year intervals. Site soils consist of 45 feet of loose saturated sand and silt overlying 70 feet of very soft to stiff (N60 = 0 to 7) normally consolidated clay. Adding to the complexity of the site is the owner?s requirement that all existing structures remain open and in service during construction of each subsequent structure. The paper presents the site geotechnical information and the foundation design issues. Details of a combination of ground improvement methods is presented, including stone columns, wick drains, a preload surcharge, and staged construction to provide soil support for shallow foundation construction of all structures at this site. The soil test results and settlement observations are presented along with QA/QC measures. Lastly, a brief method sustainability comment will be made.

Jan 1, 2010

By John F. Elliott, David L. Schroeder

SURFACE depletion can be a significant source of error in the use of the effusion method for determining the thermodynamic properties of alloys, particularly in the case of solid alloys.' However, as yet this problem has not been treated quantitatively by experimentalists in the field.1-3 The method necessitates diffusive transport of material out of the source alloy to obtain a relevant measurement. The general character of the system is shown in Fig. 1. The diffusive flux (nD) at the alloy surface is equal to the effusive flux (nE): where D is the diffusion coefficient of the diffusing substance, C is its concentration, X is the distance from the surface into the source alloy, p is the density of the alloy, and AS is the actual available surface of the alloy. The concentration of the diffusing substance at the surface is CS, and Here fE is the Clausing factor, AE is the area (sq cm) of the orifice, y is the activity coefficient of the substance in the alloy, PO is the vapor pressure (Torr) of the pure substance, M is the molecular weight of the effusing species, and T is the absolute temperature. The differential equation for diffusive transport in the source alloy is Fick's second law. Its solution is dependent on the geometry of the source alloy. Two boundary conditions must be established to obtain the proper solution, the first being Eq. [1], or its equivalent. The solutions for several important forms of the source alloy are considered below.

Jan 1, 1967

By A. J. Smethurst, S. B. Hearn, S. Boskovic

"The problem of crud in solvent extraction is well known and can be a major handicap and operational issue. Colloidal silica can cause a number of problems including interfering with flocculation, initiating crud formation in solvent extraction (SX), decreasing SX extraction kinetics and increasing SX phase disengagement times. Flocculation can be utilized to remove some of the troublesome particulates but colloidal silica does not flocculate well and presents a different problem requiring innovative chemistry to solve. Coagulants can assist by facilitating the removal of this colloidal silica by promoting the agglomeration of the particles to a size which can be more readily settled or flocculated in solid/liquid separations. This is achieved when the coagulants bind to the surfaces, displacing water and destabilizing the colloids, whereupon they bind to each other which facilitate their amenability to conventional flocculation.INTRODUCTIONSilicate minerals are abundant in the upper layers of the Earth’s crust, and there are few mineral deposits without significant levels of gangue silicates. Silicate minerals include the pure silicas, such as quartz and other silicate containing minerals such as clays, chlorites, feldspars, as well a vast number of less common silicates.During the acid leaching of ores, two types of fine silica particles are released in solution from the dissolution of the host mineral. The first consists of partly depleted silicates, and the second is colloidal silica, which forms in solution. It is this second type which has the potential to cause crud formation as well as poor solution clarities, slow filter rates and excessive flocculant usage (Figure1)."

Jan 1, 2016

By L. P. Davidson

ThE new electrolytic zinc plant of the American Zinc Company of Illinois commenced operation in April 1941. The simple flowsheet using the standard current density and the economic reasons that dictated it are given herewith. The Evans-Wallower Zinc Co. built an electrolytic zinc plant at Monsanto, Ill., in 1929 and operated it for about two years. The plant stood idle from 1932 and was purchased by the American Zinc Co. in 1940. Because of the condition of the equipment, excepting the motor generator set, a complete rebuilding was necessary. The Fairmont City plant of the American Zinc Co. could treat the leach residues, the purification cake and the skimmings from the melting furnace in its various plants. This possibility permitted a simple flowsheet with good economic results. The flowsheet is shown in Fig. I. The calcined concentrates are leached in mechanically agitated tanks with spent electrolyte and such ferric iron solution as necessary. When the acid has been neutralized and the iron coagulated, the fluid is discharged to settling tanks. The underflow from these thickeners is filtered on a Moore filter; the filter cake leaves the plant for retreatment and the filtrate joins the thickener overflow. Zinc dust is added to this solution until the copper and cadmium are precipitated. The pulp is filtered through Shriver presses, which deliver the purified solution to stor- age tanks, and the copper-cadmium-zinc cake is shipped for retreatment and recovery of these three metals. The purified solution is electrolyzed; the regenerated acid is returned for use in the leaching plant and the cathode zinc, after stripping, goes to the melting furnace, from which it is cast in slabs. The skimmings from the melting furnace are shipped to the Fairmont City plant for reduction to metal in the retort furnaces. The choice of this simple flowsheet was made possible only because of the facilities of the Fairmont City plant. The long leaching pried, with high acid content and high temperature which characterize the high-density process, gives a higher zinc extraction but also dissolves more impurities, which must be removed. The same is true to a lesser degree of the multi-step leaching of the western low-density plants. By the sacrifice of some initial extraction, solutions can be obtained that are relatively easy to purify and give good ampere efficiency. This loss in initial extraction is made up in the retreatment of the residues in the Waelz plant. The impurities that accompany the zinc thus extracted are inconsequential when the Waelz product is treated in a distillation plant. It was recognized that this flowsheet would require a somewhat greater amount of sulphuric acid—-eithcr as acid or as sulphate sulphur in the calcine—because of poorer washing. The sulphuric acid plant at Fairmont City could deliver 60" Bè. acid to compensate for the sulphate loss and the cost would be less than the cost of more intensive washing.

Jan 1, 1943

By L. P. Davidson

ThE new electrolytic zinc plant of the American Zinc Company of Illinois commenced operation in April 1941. The simple flowsheet using the standard current density and the economic reasons that dictated it are given herewith. The Evans-Wallower Zinc Co. built an electrolytic zinc plant at Monsanto, Ill., in 1929 and operated it for about two years. The plant stood idle from 1932 and was purchased by the American Zinc Co. in 1940. Because of the condition of the equipment, excepting the motor generator set, a complete rebuilding was necessary. The Fairmont City plant of the American Zinc Co. could treat the leach residues, the purification cake and the skimmings from the melting furnace in its various plants. This possibility permitted a simple flowsheet with good economic results. The flowsheet is shown in Fig. I. The calcined concentrates are leached in mechanically agitated tanks with spent electrolyte and such ferric iron solution as necessary. When the acid has been neutralized and the iron coagulated, the fluid is discharged to settling tanks. The underflow from these thickeners is filtered on a Moore filter; the filter cake leaves the plant for retreatment and the filtrate joins the thickener overflow. Zinc dust is added to this solution until the copper and cadmium are precipitated. The pulp is filtered through Shriver presses, which deliver the purified solution to stor- age tanks, and the copper-cadmium-zinc cake is shipped for retreatment and recovery of these three metals. The purified solution is electrolyzed; the regenerated acid is returned for use in the leaching plant and the cathode zinc, after stripping, goes to the melting furnace, from which it is cast in slabs. The skimmings from the melting furnace are shipped to the Fairmont City plant for reduction to metal in the retort furnaces. The choice of this simple flowsheet was made possible only because of the facilities of the Fairmont City plant. The long leaching pried, with high acid content and high temperature which characterize the high-density process, gives a higher zinc extraction but also dissolves more impurities, which must be removed. The same is true to a lesser degree of the multi-step leaching of the western low-density plants. By the sacrifice of some initial extraction, solutions can be obtained that are relatively easy to purify and give good ampere efficiency. This loss in initial extraction is made up in the retreatment of the residues in the Waelz plant. The impurities that accompany the zinc thus extracted are inconsequential when the Waelz product is treated in a distillation plant. It was recognized that this flowsheet would require a somewhat greater amount of sulphuric acid—-eithcr as acid or as sulphate sulphur in the calcine—because of poorer washing. The sulphuric acid plant at Fairmont City could deliver 60" Bè. acid to compensate for the sulphate loss and the cost would be less than the cost of more intensive washing.

Jan 1, 1943