Search Documents

By R. T. Sorensen

Research and testing in a small scale equivalent of a commercial flota-tion plant was completed on four low-grade, iron-bearing materials from the western Mesabi range. Closed circuit-flotation of calcium-activated silica with fatty acid collector developed data for comparison with the batch process and highlighted problems not evident from previous bench testing. The four ore samples contained from 27 to 39 percent Fe and were equally represented by nonmagnetic taconite and semitaconite type materials. Iron concentrates containing 6.0 percent, or less, SiO2 were made 5, all four samples. Of the two material types, the semitaconite was the ore amenable to treatment, yielding iron recoveries of about 90 percent as cc pared with 70 to 80 percent for the other. Pilot plant tests showed that concentrate grade made in batch tests could be duplicated in the closed circuit and demonstrated that the amount of recoverable middling iron varied considerably between ore samples. The continuous tests also showed that water temperature strongly influenced results in the treatment of one ore but apparently was of indifferent consequence in another. Progress in thickening and filtration of flotation concentrates was made through introduction of tapioca flour to serve the dual role of iron mineral depressant and flocculant.

Jan 1, 1966

By R M. Smart, A T. Harrison

Backfill systems using unconventional cementitious binders have been successfully used in relatively deep and hard rock tabular mines for longwall, scattered stoping and shaft pillar removals. Two unconventional cementitious systems are discussed: A ground granulated blast furnace slag (GGBS) with an activator containing lime. This has been used with a total tailings æstableÆ slurry at a relatively low dosage of less than seven per cent, by mass, based on dry solids. The room and pillar stopes supported with this fill were up to 20 m high and the tailings were relatively high in pyrite. A GGBS binder plus a silicate based activator and gelling agent that virtually eliminated all water drainage (and hence post filling shrinkage). The system used a slurry, but the addition of the activator created a final placed product that had the behaviour of a paste. The system has been successfully used for almost ten years in the following applications: stoping widths (mining heights) above 1.6 m; and shaft pillar removals in seismically active areas at the end of the life of the shafts. This paper discusses the technical merits and costs of the systems and compares them to other fill systems (including true paste systems). the acceleration (normally g, 9.81m/sec2) is increased to a significantly larger (but generally unmeasured and unknown) value, as shown in Figure 1.

Jan 1, 1998

By F Schoenbrunn, T Laros

Deep paste thickeners have been proven capable of consistently producing medium to low slump material for disposal without the need for filters. However, proper design of the entire system is critical for a paste project to be successful. Some of the factors that must be carefully considered in design of a paste system include thickener sizing, tailings impoundment design, underflow pumping, and control system.

Jan 1, 1998

The Metallurgical processes used in the gold industry in Queensland since the 1850's are reviewed. The major upswing in, gold processing this decade has brought the technology of heap leaching, carbon in pulp and carbon in leach, flotation for gold and tailings retreatment to Queensland. In many cases operators have developed or improved these processes to treat difficult ores or to cope with local climatic conditions.

Jan 1, 1989

The aim of the study was to determine the ranges of stability and instability of the metal hydroxides and metal cyanide species that may be formed during the gold extraction process, Merrill-Crowe gold precipitation, and Inco S02/Air or ferrous ion cyanide removal processes.Following cyanide detoxification by the Inco S02/Air process, the main components of concern in the tailings will be:

Jan 1, 1997

By David M. Hopstock

The performance of the most common type of low-intensity dry magnetic separator is analyzed on the basis of fundamental physical principles. Expressions are developed for estimating the optimal choice of design and operating parameters for beneficiation of magnetite ores. By proper choice of these parameters either a high-grade concentrate or a low-grade tailing can be produced from an incompletely liberated feed.

Jan 1, 1976

By A. C. Wingrove

The paper outlines the selection of a dewatered tailings backfill system for the Johannesburg Consolidated Investment Gold Division, and covers the following aspects: (i) 16 Shaft pilot testwork; (ii) engineering design problems relating to the Cooke 3 Shaft backfill operation; (iii) in-line mixing - applications with respect to the Randfontein Estates Gold Mine and Western Areas Gold Mine backfill operations; and (iv) pipeline friction losses.

Jan 1, 1988

By R. R. Wells

This report summarizes the results of laboratory testing of copper-bearing magnetite ore from the Poorman, Bush & Brown, and Copper Center deposits, Kasaan Peninsula, Prince of Wales Island, southeastern Alaska. The ores contain minor amounts of chalcopyrite and pyrite. Intimate association of these sulfides with magnetite necessitates fine grinding for adequate liberation and rejection of copper and sulfur and for the production of high-grade iron concentrate low in objectionable impurities. Laboratory tests indicated that the optimum results can be obtained by flotation of ore ground to minus-100-mesh, with subsequent wet magnetic separation treatment of the flotation tailing. A summary of results obtained by this treatment of the three samples tested is shown in table 1.

Jan 1, 1957

By J-P Franzidis, M Esvelt, E V. Manla

The Floatability Characterisation Test Rig (FCTR) is a self-contained, highly instrumented, mobile pilot plant that is able to treat up to 2 tph solids. It consists of a bank of six 130 L WEMCO« SmartCells« and a bank of six 50 L WEMCO« SmartCells«. It was developed as part of the AMIRA P9 Project, primarily to determine ore floatability characteristics and to develop and validate flotation plant modelling, scale-up and simulation methodologies. However, it may also be used to carry out pilot-scale flotation test work. This paper briefly describes the circuit modelling, simulation and scale-up test work performed using the FCTR and the use of the FCTR in pilot-plant test work performed by the metallurgical staff at WMCÆs Kambalda Nickel Operations and Mount Keith Nickel Operation. At both Kambalda and Mount Keith the FCTR was found to be very flexible and straightforward to run, with an easily changeable circuit configuration and stable operation. Testwork was facilitated through having full stream sampling on all streams, and a high degree of instrumentation providing accurate measurement of process variables. The results obtained from the FCTR testwork were highly repeatable. As a consequence of using the FCTR, WMCÆs Kambalda Operation and Mt Keith Operation were able to complete a rigorous programme of pilot plant testwork more quickly than in the past, and with a high degree of confidence in the results.

Jan 1, 2003

By P Edmondson, S Narendranathan, S Setchell

The complexities of mining in current economic conditions, where ore extraction schedules are varied on a weekly basis so as to ensure constant supply to the process plant, can result in a number of scenarios that pose geotechnical challenges. This paper presents a case study where alterations in the mining schedule of a particular mine resulted in the necessity to mine under a large uncompacted embankment, ie integrated tailings and mine waste landform. To effectively ensure that ore recovery was maximised, a well-designed slope monitoring system to evaluate design performance and to provide timely warning of impending failures was imperative. In order for an appropriate slope monitoring strategy to be developed, a thorough understanding of the potential slope failure mechanisms, capabilities and limitations of available monitoring techniques is required. Communication of the monitoring results and response strategy to alarms generated by monitoring systems must also be carefully considered to maximise effectiveness. The results of preliminary stability modelling can be used to guide the design of a monitoring system, which in turn can then generate data which can be used to iteratively refine the geotechnical model. This paper illustrates the development and implementation of a slope monitoring system and associated communication system, using a case study developed at a large iron ore open pit mine in the Pilbara region of Western Australia.CITATION:Narendranathan, S, Lee, E C, Setchell, S and Edmondson, P, 2015. Modelling of an integrated waste storage facility, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 183–190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Erik Spiller

"Water and cyanide are highly contentious and conflict issues that many gold mining companies encounter worldwide when dealing with local farming communities, industries and cities competing for water as well as non-government and government organizations. Historically, the gold industry has used processes that required minimum amounts of water to treat and recover gold at locations around the world. Examples are dry grinding for refractory gold treatment in the late 1800s and early 1900s and dry blowing in arid/desert regions to recover alluvial gold. In recent times, new dry processing equipment has been developed and include equipment such as air tables and jigs. Researchers have also modified a Knelson concentrator to concentrate gold from dry solids. High pressure grinding rolls (HPGR) with air classifiers are used to treat industrial minerals and pilot trials have shown that the technology can be applied to comminute refractory gold ores ahead of roasting. Dry stacked tailings is being applied on gold mines to reduce overall water consumption This paper will review the available technologies that in combination may be able to substantially reduce the quantity of water used in the processing of gold ores.INTRODUCTION Water makes up most of the world: the planet is 75% water. Some 97.5% is saline water largely in the oceans, so that only 2.5% is fresh water and useful for human needs. The demand for water is driven primarily by population and concomitant economic growth. Overall, some 70% of the water withdrawn from the environment is used in agriculture, 20% by industry, 7% by households and 3% for mining (Brown, 2003: Maupin et al., 2010). Whilst the water needs of the mining industry are minor compared to those of agriculture, an operating mine requires a relatively large quantity of water on a daily basis to carry out operations. Mining activities are often located in remote, arid environments, with limited access to water. There are a multitude of water resources available to the mining industry for its needs. However, much of this water is saline and over the last two decades there has been a continual decline in water quality (i.e. salinity has increased). In today‘s world, there are enormous internal and external pressures to reduce water consumption at a mine, and/or alternatively use water not considered a resource by the local community. Strategies to meet these objectives can be achieved by implementing good water management practices, by recycling process water, reducing water losses by evaporation and seepage (i.e. by increasing and improving dewatering practices) and employing new technologies such as dry stacking and dry processing (Dunne, 2010)."

Jan 1, 2017

By M Norbert, P Mok

The mainline running tunnels for Legacy Way comprise of two-lane tunnel boring machines (TBM) driven tunnels. The length of the TBM tunnel section is approximately 4.2 km. The TBMs employed are double shield TBMs. Typical support to the segment ring while advancing a double shield TBM comprises of filling the excavated annulus between the ground and the segmental lining by injecting pea gravel, followed with primary grouting to fill between the pea gravel some distance behind the excavated face. The methodology adopted for the Legacy Way project, however, did not follow this typical approach, instead, two component grouting of the annulus was carried out.Where the annulus is typically filled with pea gravel, support is provided to the segment ring very close to the end of the tail shield, whereas in the case of two component grout this is not practical as the risk of grouting in the tail shield is high. The staging of the two component grout injection, the grout early age strength properties become key issues in ensuring that the segment ring leaving the TBM tail shield is stable and can support the necessary external loads.Two-component grout is a grout with two components, cementitious grout (component A) and accelerator (component B), commonly adopted for earth pressure balance (EPB) TBM. The grout reaches its thixotropic state in a matter of seconds providing initial support for the segment rings. Manual injection of two component grout to fill the bore annulus was carried out in stages leaving a portion of the segment rings unsupported. Ring stability during TBM advance was provided by a combination of ram thrust and the segment circumferential joint shear connectors.This paper outlines the design considerations such as rock load derivation by probabilistic analysis carried out utilising the software JBlock, 3D finite element analyses using the software Strand7 for ring stability and the testing and back analysis of the shear connector load bearing behaviour. In particular, the actual available capacity of the shear connectors against their published capacity by supplier was discussed.CITATION:Mok, P and Norbert, M, 2014. Tunnel boring machine excavation stability – double shield tunnel boring machine advance with partially grouted annulus, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 51–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By D Audeyev

The Cooljarloo North Mine has been shaped not only by operational and processing challenges, but by climatic and economic factors. This paper outlines some of these challenges and discusses how the operating strategy has been altered over time to mitigate the impacts.Since commissioning the wet concentrator in 1999, there have been many typical operational challenges to maximising valuable heavy mineral (VHM) recovery. These include: varying in pit feed grades, different slimes types and volumes, sizing extremes between VHM and trash minerals and decreased equipment reliability handling rocky ore. These issues were successfully mitigated by: in pit extraction strategies, upgrade of the de-sliming circuit, thickener modifications and flocculent changes, installing upgraded and additional spiral capacity, and various Feed Preparation Plant screening initiatives. Combined with the ingenuity, persistence and patience of the operating team, VHM recovery >95 per cent has been achieved.However, typical processing challenges have not been the only hurdles. Reduced rainfall and water availability has necessitated the strategic co-disposal of tailings and slime to increase the speed of water recovery: groundwater abstraction and water storage strategies have also been altered. With an observed reduction in the speed and magnitude of groundwater recharge, overburden backfill scheduling has become a priority mine planning function.Combined with the above challenges, the prevailing foreign exchange rate and mineral product prices have impacted profitability. At the height of the Global Financial Crisis in 2009, major changes to the operating strategy were made to maintain a viable dry mining operation in 2010. Working with the mining contractor the existing scraper and semi-fixed Feed Preparation Plant set up was replaced with a movable in pit dozer trap facility. The end result of changes to the mining method and primary screening was a ten per cent reduction in unit costs. This article will elaborate on some of the above mentioned challenges and successes achieved over the past ten years of operating the Cooljarloo North Mine.

Oct 5, 2011

By Louis R. Bernier

Since 1978, most systematic studies of AMD passive treatment with limestone drains (LD) have dealt with coal mines in the United States. The authors present in this paper the first results of a triennial study initiated in 1999 on the performance of LD installed at the Ni-Cu Lorraine old mine site in Temiscamingue during a remediation plan that involved the installation of a cover with capillary barrier effects (CCBE) over the reactive pyrrhotite-rich tailings. Typically, a LD is a trench enclosed by impervious materials filled with crushed limestone and may be oxic or anoxic. Four LD (one filled with marble and 3 with dolomite) were installed at the Lorraine site. The LD have been in operation since May 1999 and are performing differently. The most contaminated mine effluent flows south and is directed towards 3 LD filled with crushed dolomite, while a 4th LD was filled with crushed marble and installed west. The LD filled with marble has been generating maximum alkalinity since the beginning of the passive treatment. Two of the dolomite drains have been generating alkalinity since mid-summer 1999, but one is not, even if a substantial pH raise was observed. A pH above 5.5 is required usually for the dolomite drains to start generating alkalinity. The installation of LD at the Lorraine site contributes significantly to the reduction of metals and sulphates loading.

May 1, 2001

By Steven J. Page

Longwall double-drum shearers frequently have difficulty complying with the 2.0 mg/m3 dust standard and, therefore, require the use of effective dust controls. However, before dust controls can be implemented effectively, the major individual dust sources must be determined and their relative severity evaluated. The Bureau of Mines has recently developed a sampling strategy, based upon short-term gravimetric sampling, that can identify the major dust sources contributing to the shearer operator's exposure. This technique utilizes approved gravimetric sampling equipment already available to all mine operators and can be performed by two people in 2 days. Five examples, including data analysis, are discussed with respect to various cutting sequences. In addition, typical dust source contributions obtained from studies of double-drum shearer operations regularly in compliance are included. Mine operators can thereby compare their dust source evaluation results with those from these longwalls.

Jan 1, 1982

By Houyuan Liu

A new process was developed to recover nickel and cobalt by leaching laterite ore at atmospheric pressure and.95"-105" C. The nickel-containing goethite in limonite was first leached with sulphuric acid to liberate over 90% of nickel, cobalt and iron. The dissolved iron was then precipitated as Ni-free goethite by the additioil of saprolite. The acid released during iron precipitation as goethite was simultaneously used as lixiviant to leach saprolite to recover more nickel. With this process the limonite and saprolite were essentially converted into goethite-, gypsum- and silica- containing tailings. Twenty bench scale tests and two campaigns of pilot plant operation were carried out at BHP Billiton's Newcastle Technology Centre (NTC) from January to August 2002. The overall nickel and cobalt extractions were 81 to 90% and 91 to 100% respectively. The average plant availability was 99%. The advantages of this process over existing processes include high plant availability, high consistency, robustness and simplicity of the operation.

Jan 1, 2004

By Michael T. Nigbor

This Bureau of Mines publication identifies the significant environmental issues associated with the potential development of strategic and critical minerals in the Stillwater Complex, MT. The Stillwater Complex contains deposits of Cr, platinum-group metals (PGM), and Ni. Issues that must be addressed prior to minerals development include the effects mining, milling, and smelting will have on the land, water, and air, and methods of minimizing the environmental impacts.

Jan 1, 1985

By A. I. Urvanzev, N. V. Shikhov

"In this paper, we present the study’s results of electrical separation processes on the basis of new separator designs, new technological solutions, and newly discovered effects. We considered the options of enrichment by magnet separation of magnetite and titanomagnetite ores, ores and products containing chromium and manganese, ores of non-ferrous and precious metals. During pneumo-electric separation of mixed iron ore of SMPC, 43.3% of the output of the concentrate with an iron content of 61.7% was obtained in one step, with extraction of 70.5%. The paper also presents the results of the finalization on the air-electric separator of the magnetic fraction when separating oxidized ores of MPPOO (mining and processing plant of oxidized ores) on the Jans polygrade magnetic separator. A concentrate was obtained with an iron content of 65.1% with the extraction of 95.0% and tails with an iron content of 13.0%. The possibility of obtaining low-silica concentrates from these ores with an iron content of 67.15 and a quartz of 2.88% is shown. Also, the results of tests on the enrichment of chromite ores on the firing-magnetic scheme with corona-electrostatic separation are considered. On the initial ore of the Don MPP (mining and processing plant), a concentrate with a content of 61.8% Cr2O3 was obtained with a quartz content of ~ 1.0%. The results of pneumo-electric separation with triboelectric charge of the separated particles are presented. The results of the tests indicate a principal possibility of enriching chromite ores without costly high-temperature roasting. Dry technology of enrichment of manganese ores with the use of electrical separation increases the quality of the oxidized concentrate to the first grade and raises the total extraction by 2 times. For the Chineya deposit of titanomagnetite ores with copper impurities, electroseparation operations were carried out on two samples with a Cu content of 1.93 and 3.75%, respectively. For a sample with a Cu content of 6.02%, a copper concentrate output of 24.42% was obtained with a Cu content of 23.82% and the extraction of 94.88%. The results of enrichment by electroseparation of gold-containing sulfide ores can have the practical importance. For ores of the Berezovskoye deposit, a pyritic concentrate containing 100 g / t of gold was obtained after two or three operations of IES (integrated energy systems)."

Jan 1, 2018

The Beginning ! The status quo simply isn?t sustainable ! Our social license is at risk ! The bar keeps rising ? We must improve our performance, both operational and social ? We must improve stakeholder judgement of our industry by taking action collectively Implementing TSM " TSM Guiding Principles " Performance Indicators " Crisis communications " External Outreach " Tailings management " Energy management " Performance manuals, guides " Reporting " Communities of Interest Advisory Panel

May 1, 2004

By D J. Williams, C Zhang, F E. Herrera Cabrera

Farming on bauxite residue using screw propelled equipment (SPE) has been commonly practised to accelerate dewatering and as it promotes consolidation and enhances storage capacity. However, it is unclear when and how often farming should be conducted during the transition of bauxite residue from slurry to dry solids and how deep each slurry deposition should be. To address this issue, three desiccation tanks were established in the laboratory to investigate how much farming could enhance the desiccation and consolidation of tailings. The cuboid tanks, of 350 mm in height and 300 mm in width and length and with an opening on the top, were placed on load cells to monitor the water loss during desiccation and were instrumented with moisture and suction sensors designed and developed at the University of Queensland to measure the water content profile of the residue. The bauxite residue, composed of silt-size particles with low plasticity, was hydraulically deposited in the tanks as a slurry at 27% solid content, resulting in 100 mm depth of solid material settling. Evaporation was enhanced by placing two identical electrical fans above the tanks. Two phases were conducted. In the first phase, the two tanks were left untouched for evaluating non farmed conditions and for calibrating sensors, while in the second phase, three tanks were subjected to atemporal farming using purpose-built screw propelled equipment. The experiment was terminated when the residue was completely desiccated. This paper reports on the instrumented tank set-up and the results obtained to date.

Jul 1, 2021