Search Documents

By Chanki Jeong, Heechan Cho

In this study, batch flotation experiments were conducted to recover rare earth elements (REE) from an REE ore deposit in the Mushgai Khudag area, Mongolia. Apatite was found to be the major REE mineral while monazite and xenomite were observed as minor minerals. The main purpose was to float apatite to increase the REE content. Oleic acid was used as collector and MIBC was used as frother. Sodium silicate was used as a depressant for iron compounds. NaOH was used to adjust the pH of the flotation to about 9.5~10.0. The particle size was 90% less than 152 ?m (- 100 mesh). The content of REE elements was analysed by ICP - OES to determine the contents of REE such as Ce, La, Nd, Pr and Y. When sodium silicate was used, the best result was obtained using 0.2 mL of sodium silicate, 2 mL of oleic acid and 2 mL of MIBC. Under these conditions, the recovery of REE was about 78% and the grade of the first froth product was 42,995 ppm Ce, 24,088 ppm La, 14,236 ppm Nd, 4,388 ppm Pr and 1,570 ppm Y. When conducting flotation after iron minerals were removed by magnetic separation, a better result was obtained; with 2 mL of oleic acid, 2 mL of MIBC and no sodium silicate, the recovery was increased to 90% and the grade was also increased to 58,600 ppm Ce, 28,624 ppm La, 17,160 ppm Nd, 5,348 ppm Pr and 1,971 ppm Y.

Jan 1, 2014

By B. D. Sparks, I. E. Puddington, F. W. Meadus

The continuous separation of bitumen from Athabasca tar sands, with a high clay content, has been demonstrated. Recoveries of 95 per cent or higher have been obtained. Further processing of this product, to produce an accept-able type of crude oil, would require less heat than currently used in the hot-water process. Also, by comparison, substantial savings in equipment and operating costs are indicated.

Jan 1, 1971

By Karen Tempel

Newmont's Lone Tree Mine is located 30, miles east of Winnemucca in Humboldt County, Nevada. Starting in February 1994 a pressure oxidation circuit was commissioned to treat refractory gold ores. Gold is leached and recovered from the oxidized slurry in a six-stage carbon-in-leach (CIL) circuit. Lone Tree has been able to maintain tighter control' of cyanide addition and reduce cyanide consumption its CIL circuit through the installation of Degussa's Cyplus® CCS Cyanide Control System in the spring of 2000. 'The Cyplus® CCS, along with additional inputs' from plant sensors, has allowed tor a more efficient and effective control strategy over the manual control method used ,in the past. This paper documents the key aspects of the Cyplus® CCS installation; the development of the control strategy, and the benefits achieved from enhanced control.

Jan 1, 1998

By Cristian Saavedra, Patricio Zarate

Flotation collectors play a crucial role in mineral flotation by selectively adhering to mineral surfaces and aiding in their separation from gangue material. They are heteropolar molecules, as defined by Sutherland and Wark (1955), featuring non-polar hydrocarbon chains and polar groups interacting with mineral surfaces to induce hydrophobicity selectively. The importance of collectors in mineral processing, as underscored by Lotter and Bradshaw (2010), lies in their ability to enhance recovery rates and improve selectivity, thereby optimizing the extraction of valuable minerals from complex ores. Collectors are classified based on their mechanism of action, as proposed by Laskowski (2010). This classification categorizes collectors into three groups: water-soluble compounds, water-insoluble “oily” collectors, and water-insoluble amphipathic compounds forming molecular films at the water/gas interface. This complements the chemical structure-based classification by Sutherland and Wark (1955) and Suoninen and Laajalehto (1993), offering a comprehensive understanding of collector diversity in flotation systems. Collector selection is an iterative process crucial for optimizing mineral processing efficiency, as emphasized by Lotter and Bradshaw (2010). Understanding the significance of collector mixing or synergy outcomes is paramount for enhancing mineral flotation efficiency and sustainability. Taguta, O’Connor, and McFadzean (2018) demonstrate that mixed collector systems enhance interaction enthalpies and microflotation recoveries, indicating improved performance. McFadzean, Castelyn, and O’Connor (2012), along with Critchley and Riaz (1991), delve into investigating synergistic interactions between collectors, offering insights for strategic selection. Observations from the study of collector synergy, as noted by Wakamatsu et al. (1980), reveal nuanced relationships surpassing individual collector behaviors. The methodology outlined in this paper provides valuable guidance for classifying and selecting collectors based on specific application needs, while also suggesting the potential for synergistically improving recovery across fine, intermediate, and coarse particles.

Feb 1, 2025

By Aparup Chattopadhyay, Barun K. Gorain

"Porphyry copper deposits are the most important source of copper and also gold within the orogenic belts. These deposits are characterized by low grade copper ore (0.2% to 1% copper) and host precious metals like gold, silver and platinum. A characterization tool has been developed for complex porphyry type copper-gold deposits with an aim to quantify copper and precious metal deportment. This quantification is a challenging task due to low grades and also due to the presence of both visible and invisible precious metal content in different sulphide and non-sulphide phases. Studies were initiated on various complex ore deposits and also on samples representing various processing streams such as flotation and leach products. This paper presents the development of a systematic approach to diagnostic metallurgy using state-of-the-art optical and automated mineralogy, micro-probe, dynamic SIMS and TOF-SIMS analysis for quantification of invisible and visible precious metals content in various species. The relevance of this characterization to metallurgy will also be briefly discussed in this paper.INTRODUCTIONA novel characterization tool has been developed for double refractory gold ores and complex copper-gold ores using state-of-the-art technology for quantitative gold and copper deportment study. The characterization of these ores is a challenging task due to low copper and gold grades in ores, presence of both primary and secondary copper sulphide phases and variable proportion of visible and invisible gold in different sulphides phases (pyrite, chalcopyrite, chalcocite and bornite) and iron oxide phases (magnetite, hematite and goethite). A study was initiated on various ore deposits and also on samples representing various processing streams of pilot plant batches such as flotation concentrates and tailings. This paper attempts to discuss the deportment characterization methodology through presenting results from investigations on four samples from a flotation circuit viz, Feed, Final concentrate, Cleaner Scavenger Tail and Rougher Tail samples. These four samples represent the key streams for a typical copper-gold flotation flow sheet. The key objective of this investigation was to identify and quantify visible and invisible gold along with understanding the morphology and liberation of gold associated with various sulphides, Fe- Oxides and non-sulphide gangue species. In addition, the aim of this study was also to relate this mineralogical and gold deportment information to metallurgical performance."

Jan 1, 2013

By Fangming Liu

The key problems of current flowsheets and equipments are analyzed. A new steel slag's crushing flowsheet whose key equipments are the improved inertia cone crusher and inertia vibrating jaw crusher is proposed. An advanced two stage open-circuit crushing method is adopted in the flowsheet, with 90% of particle size crushing under 6mm. Using inertia vibrating technology and selective crushing principle the crushers can realize steel slag separating fully into steel and slag and with flexible transmission mechanism the crusher can be protected when iron lump is passing. The flowsheets can enhance the recovery of metal greatly, and expand the application range of tail slag and added value.

Sep 1, 2012

By Edward E. Johnson

The principal purpose of this study was the development of an engineering and economic model of a hypothetical large-scale open pit gold mining operation. The guiding concept in developing the model was the idea that, through study of a number of such models, it would be possible to evaluate a mineral property and to make reasonable estimates of the benefits to be derived from research in mining and metallurgy. The model by use of a computer is able to produce results easily and quickly when cost factors are varied. Cost factors may be varied as a result of assumptions of improved technology or of assumptions of assuming different approaches or methods to accomplish a particular segment of the mining or processing operation. The discounted cash flow rate of return was used to measure the effect of changes in costs or expected revenue. In this study, assumptions based on past processing practices were made in an effort to reduce costs of processing the ore These assumptions were: (1) Eliminating the low-grade cyanide circuit; (2) reducing the quantity of material to be processed by screening after crushing; and (3) using a combination of assumptions (1) and (2). All three assumptions resulted in reduced capital investment and operating cost that caused substantial increases in the rate of return.

Jan 1, 1968

By Binyon E. O.

The tungsten properties of Lincoln Mines, Inc., and North Tem Piute Mining and Development Co. were first explored by the Bureau of Mines in 1942. Work on the project comprised trenching, sampling, a small amount of road and trail construction, and a small amount of core drilling. From April 13 to December 10, 1944, additional diamond drilling was done by the Bureau of Mines to test the lateral and downward extensions of the various tactite zones along the contact south of the Lincoln mine, including the property of the North Tem Piute Mining & Development Co. Claims leased by the Lincoln Mites, Inc., are in secs. 25 and 36, T. 3 S., R. 56 E.; secs. 30 and 31, T. 3 S., R. 57' E.; and sec. 1, T. 4 S., 56 E., M. D. B. & M., in the Tem Piute Mining District, near the north end of the Timpahute Range in west central Lincoln County, Nev. D. B. Fegles is president of Lincoln Mines, Inc., and general offices are in the Wesley Temple Building, Minneapolis, Minn.

Jan 1, 1950

By J. V. Batty

The Bureau of Mines devised techniques involving the use of beta-and gamma-ray-emitting radioisotopes and successfully adapted these techniques to the density of mineralized flotation froths) the rate of flow of finely ground ore pulps) and the residence time of pulps in processing circuits. Specifically, the water and mineral loads of flotation froths were continuously measured by determining the proportion of a constant-strength beam of beta rays that was absorbed by the froth column. Continuous measurement of the rate of flow of an ore pulp was accomplished by measuring the changing width of a free-falling stream of the pulp with a collimated beam of beta rays. The residence time of solids in conditioning and resin-in-pulp circuits was accurately measured by following the progress through these circuits of a portion of the pulp that had been tagged with the gamma-emitting Ag110 radioisotope.

Jan 1, 1966

By Brian L. Beninger

This paper discusses the application of the computer to coal preparation process predictions. In broad terms, the computer is used to perform two main functions. Firstly, the given float-sink analysis is interpolated and extrapolated to cover the entire actual range of raw coal specific gravity. Assumptions based on historical data must be made at times. Secondly, the partition curve, which, from historical data, defines the efficiency of a specific coal washing process, is applied to the washability data in order to determine the expected clean coal yield and quality. The vast amount of numerical work which is required to make a prediction of this type exhibits the need for computer methods in this area.

Jan 1, 1979

By W. O. Vanderburg

This paper describing the methods of concentrating tungsten pros at the mills of the Atolia Mining Co. is one of a series of similar papers being prepared by the United States Bureau of Mines. The writer acknowledges the assistance and cooperation of A. V. Udell, president, Louis Warnken, bookkeeper, and C. K. Dennis, superintendent, of the Atolia Mining Co. in the preparation of this paper.

Jan 1, 1931

By A. Leppala

Scope of the Courier 300 System The fact that reliable on-stream analysis is a prerequisite for effective flotation control is hardly disputed today. Nevertheless, up to now no system has been available that includes all the equipment necessary for successful analysis. However essential an on-stream analyser is in itself, reliable and accurate assaying can only be assured after techniques for sampling, handling the slurries and computing the X-ray data have been developed for the purpose. The Outokumpu Company's Courier 300 System is a complete package that can be installed and handed over with the key. It includes the equipment needed for sampling and handling the slurries. It has been developed from the start to meet industrial demands. Obviously an on-line system must comply with far stricter standards than one designed for a laboratory. Assays are computed by an Outokumpu 316 digital data processor, which is an integral part of the system and controls its entire performance. The computer software is programmed as a standard package, including a highly advanced new model for assay computation. Analysis output is available for a process computer, report typewriter:, and recorders. The package also includes calibration for slurry assays at our pilot installation before delivery. A complete Courier System can analyse up to 4Z slurries and six elements in each slurry. Thanks to its modular design, it can be dimensioned initially to the customer's requirements and is easy to expand later at low cost. Being a mining company itself, Outokumpu has been able to utilize its own long experience in non-ferrous metallurgy - an important factor contributing to the success of the Courier system. History of the project and present installations The first on-stream analyser was installed at Outokumpu'a Pyhasalmi Con¬centrator at the end of 1967, after several years' development. Since then,

Jan 1, 1971

In October 1993 it was decided to undertake the fourth phase of mining at Big Bell. This decision followed the exhaustion of open pit reserves in January 1993. Two stages of mining were proposed for the new underground mine. The initial stage would mine the remnant ore, consisting of the rib and crown pillars and lower grade ore on the hangingwall and footwall side of the old open stopes, which were mined from the 1930s to 1950s. Most of the old open stopes were backfilled with either deslimed mill tailings or development mullock, both of which were economic to recover. However, the mineable ore from this resource was difficult to evaluate. The second stage focused on mining ore outside the remnant areas and was initially proposed as a Core and Shell method under a caving hangingwall. This method has since been superseded with sublevel caving, in part due to the very high and deviatoric stress conditions encountered at Big Bell and the relatively long mining cycle required for open stoping. The problems and challenges discussed in this paper will cover the identification of remnant ore reserves, dewatering the old workings, and remnant mining.

Jan 1, 1998

By J J. Boshoff

This iron ore mine site, located in the Pilbara region of Western Australia, commenced operations in 1998, with ore derived by mining of open-cut pits in Channel Iron Deposits (CIDs). A portion of the ore extracted at the mine is processed at wet processing plants that produce both ore saleable product and waste fines (i.e. tailings) slurry. The waste fines produced at the wet plants are presently stored within Waste Fines Cells (WFCs).Waste fines cells A (WFCA) and B (WFCB) are located within an Autonomous Haul System (AHS) area and consist of embankments that span the width of the pit in east-west alignments. Technical studies and design analyses were carried out to support embankment raises and ongoing development of the WFCs. During operation and development of the WFCs, a multitude of simultaneous activities took place to the immediate north and south of WFCA respectively. These activities included the construction of the embankment raises using the AHS fleet, mining of the CID to not only mine the ore but to also create future deposition space for WFCB, blasting next to the WFC embankments as part of the mining activities, seepage collection and dewatering of the pit in the vicinity of the WFC.This paper discusses the material characteristics, design approach, construction staging and equipment requirements, blasting near embankments, water management, facility consequence category and closure concept.CITATION:Boshoff, J J, 2018. A waste fines cell with a multitude of concurrent activities, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 39–49 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By A. Demirag, F. Burat

"The most important metals in the jewelry sector are undoubtedly gold and silver. As a result of workmanship work done in the jewelry industry, the tiny metal and jewel fragments and metallic powders are scattered. Given the prices of gold and silver on the market, the dust that emanates from these workshops is of great importance. Gold recycling has become as important as raw material production within the mass market and gold production industry. In 2016, 29% of the world gold supply has been obtained through recycled gold production. Waste derived from jewelry activity is included in this category, and represents an essential component of this percentage. In the scope of this study, the recovery possibilities of Au and Ag from jewelry sweeps floor sample was investigated using flotation method. In the experiments, optimum pH value, particle size, the effect of dispersant, type and amount of reagent were investigated. As a result of these studies, it was determined that the optimum pH value was 6.5 and the particle size was -212 microns. It was observed that the most suitable reactive combination was Aero 242 and Aerophine 3418A and Na2SiO3 has no positive effect on recovery of Au and Ag as a dispersant agent. As a result of tests, a final concentrate containing 268 ppm Au and 2122 ppm Ag was obtained with 81.4% and 74.5% recovery respectively. INTRODUCTION Because of the softness of pure gold, it is usually alloyed with base metals for use in jewelry, altering its hardness and ductility, melting point, color and other properties. On the other hand, gold has some special chemical properties which in normal conditions, don’t react with water, dry or humid air, oxygen, ozone, nitrogen, hydrogen, fluorine, iodine, sulfur and hydrogen. In these days, gold is used in different sectors like jewelry, electronics, finances and investing, dentistry, medicine, aerospace, awards & status symbols. According to Deutsche Bank Research, the primary usage of gold is jewelry. It has been used to make ornament and jewelry for thousands of years. In this sector craftsmen learned that alloying gold with other metals like copper, platinum and silver to increase gold’s durability. Alloying gold with other metals changes the color of the products. Another significant sector of gold is electronics. Modern electronics want the use of noble metals, like gold, especially in the areas of information processing, telecommunications, and military and space electronics (Habashi, 1997). Electronic devices use very low voltages and currents which are easily interrupted by corrosion or tarnish at the contact points. Gold is the highly efficient conductor that can carry these tiny currents and remain free of corrosion. Electronic components made with gold are highly reliable. Gold is used in connectors, switch and relay contacts, soldered joints and connecting wires. Every sophisticated electronic device have a considerable amount of gold. This includes cell phones, calculators, personal digital assistants, GPS units, and other small electronic devices. Most large electronic appliances such as television sets also contain gold. Humankind has known silver since prehistoric times like gold because silver occurs in native form. The metal is found in the Earth's crust in the pure, free elemental form native, as an alloy with gold and other metals, and in mineral such as argentite. Most silver is produced as a byproduct of copper, gold, lead, and zinc refining. Silver is very soft metal like gold also, it is the highest electrical conductivity, thermal conductivity, and the lowest electrical contact resistance of all metals (Habashi, 1997). Silver is used in different sectors like industry, jewelry, electronics, photography silver good, and coins. The main usage of silver is supplied by electronics. Silver's unsurpassed thermal and electrical conductivity among metals means it cannot easily be replaced by cheaper materials. In addition to silver is using in ener"

Jan 1, 2018

By Jie Deng, Wenliang Xiong, Binyan Chen

"With falling rare earth metal prices, low cost beneficiation of rare earth minerals is essential. The “Flotation-Agglomeration-Magnetic” (FAM) separation process is a newly developed technology by IMUMR to economically recover rare earth elements from different types of deposits. The theory of FAM process is to selectively agglomerate rare earth particles and separate from gangue minerals by bubble flotation process. The flotation product is further upgraded by magnetic separation. The FAM process has been successfully applied in industrial production on the Dalucao rare earth ore, Sichuan, China. The average REO grade of rare earth concentrate is 65% in the latest 12 month production run, with an average recovery of 55%.INTRODUCTIONRare earth elements (REEs) include fifteen lanthanide elements coupled with two chemically similar elements (yttrium and scandium). These elements are split into two sub-groups, La to Sm are classified as light rare earth elements (LREEs) and the remaining elements including yttrium are heavy rare earth elements (HREEs) (Kumari & Panda, 2015). The demand of rare earth elements surged in recent years due to their increasing usage in diverse industrial aspects including high strength magnets, phosphors, clean energy, polishing compounds and catalysts (Goley &Scott, 2014).More than 250 REE-bearing minerals have been discovered, but many minerals are with very low concentrations of REEs, varying from 10-300 ppm (Adam &Ping, 2013). The most common rare earth minerals mined are bastnaesite, monazite, xenotime and ion-adoption REE (Chelgani & Rudolph, 2015; Kanazawa & Kamitani, 2006). Before the 1960s, most rare earth resources were extracted from monazite in the beach placer, with the exploiting of Mountain Pass in the United States and Bayan Obo mine in China, bastnaesite became the chief mineral source of rare earth resources (Klinger, 2015). These minerals are commonly separated with gangue minerals by froth flotation, gravity concentration, magnetic separation, or any combination thereof based on their specific physical characteristics (Zhou & Wang, 2014; Adam & Richard, 2014; Yang & Satur, 2015; Xia & Brian, 2015a,b)."

Jan 1, 2016

By LIONEL E. BOOTH

ORE tests are made for the purpose of determining the correct methods of treatment for any particular ore. They should be conducted so as to insure that the results obtained in actual mill practice, on ore of similar grade and physical nature, will duplicate the results obtained in the test work. As the expenditure of many thousand of dollars may be involved in the building of the necessary mill, the testing of ores calls for extreme care and skill in handling laboratory machines, and a knowledge of actual practice to guard against the danger of obtaining results in test work that would be impractical to duplicate on a commercial scale. The importance of a correct sample of the ore is at once apparent. No matter with what degree of care the test 4rk is done, it loses its value when made on an unrepresentative sample. It is the first safeguard against future disappointments in the loss of capital and time. A number of failures in the past have been traced directly to faulty or lax methods in obtaining the ore sample.

Jan 1, 1924

By A. Blake Caldwell

Tyrone-a complete mining and concentrating facility built by Phelps Dodge Corp.-straddles the Continental Divide where surface water on either side flows in opposite directions although all water is taken from and returned on the northwest side of the Divide. At the outset, Tyrone was saddled with a problem of an adequate water supply, and the Gila River some 23 miles distant appeared to be the logical source. This in itself presented a major obstacle to Phelps Dodge because of the distance water had to be pumped and because of an adverse head which had to be overcome between the Gila River and the two 4-million-gal-capacity terminal water supply tanks at the mill. Having acquired water rights on the Gila River and in order to control the seasonal fluctuations in water volume, the company built the Bill Evans, off stream, earth-filled dam. This reservoir will contain 2100 acre-ft of water when full and it was constructed by the Hamilton Construction Co. for Phelps Dodge. The dam impounds fresh water for the Tyrone plant's use and four vertical turbine pumps (4500 gpm each) lift the water 275 ft from the Gila River into the reservoir. Since construction, Phelps Dodge has optioned the lake to the New Mexico State Game Commission for recreational purposes. In addition to the lake, land around the reservoir has been optioned to the State Game Commission for public use. The lake has already been stocked with trout and by next summer some keepers should be available for the taking.

Jan 12, 1969

By Carl Belser

Approximately 30 million pounds of tungsten trioxide in the form of ferberite concentrates have been shipped from Boulder County. Since 1940, the production has varied considerably, being affected by the emergency needs of World War II and the Korean conflict. During World War II, attempts to stimulate production were made by the Metals Reserve Company by stabilizing the price for a specified period, the Reconstruction Finance Corporation by small mining development loans, and the Bureau of Mines and the Geological Survey, who cooperatively explored some of the district by surface and underground core drilling. During the Korean conflict and continuing through the first half of 1954) tungsten production was being stimulated by a Government-gauranteed price and by financial assistance loans under the Defense Production Act of 1950 to qualified operators of properties that have merited exploration. This combined program has increased production in Boulder County from about 1,900 pounds in 1949 to an estimated 383,000 pounds of tungsten trioxide in 1953. The 1953 production came from 67 properties. One of the problems confronting producers is the need for improved beneficiaton methods. Ores from the area have not been amenable to flotation concentration and gravity methods have resulted in poor recovery, often less than 70 percent.

Jan 1, 1955

By T D. H McGrath, J P. Vaughan, J Heath, J J. Eksteen

A reliable laboratory method to characterise the response of free gold particles when subjected to flash flotation conditions has been developed by AMIRA P420 researchers at Curtin University. This test has been applied to assess the flotation recovery of gravity recoverable gold from free milling ores as well as synthetic ores featuring either a gravity concentrate or gold powder. Trends in free gold flotation kinetics as well as size and milling effects were identified for gold recovery, based on the different gold types, reagent dosage and residence time.CITATION:McGrath, T D H, Eksteen, J J, Vaughan, J P and Heath, J, 2013. Laboratory flash flotation trends for a variety of gold particles, in Proceedings World Gold 2013 , pp 357-366 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013