Search Documents

By K. E. Tame

The Bureau of Mines is studying possible modifications in conventional ore-processing methods that will confine and permit controlled disposal of radioactive liquid wastes. Stream and ground water pollution from radio-active nuclides, principally radium 226 and thorium 230, in liquid wastes from uranium mills can be minimized by reusing the waste solution within the mill. Such reuse of waste solution in an acid leach-resin-in-pulp flowsheet was investigated in the laboratory. The process consists of acid leaching for dissolution of the uranium, sand-slime separation and countercurrent decantation washing for recovery of a pregnant slime slurry, and the use of ion-exchange resin for recovery of uranium from the slurry. Reuse of clarified barren effluent for washing in the simulated mill circuit was carried through 55 cycles. Dissolution of uranium from the ore averaged 97.5 percent. Washing efficiency of 99.9 percent was attained when using 4.35 volume tons4 of combined barren effluent and makeup water per ton of ore. Absorption of uranium from the pregnant slime slurry by an ion-exchange resin averaged over 99.9 percent.

Jan 1, 1962

By Peter N. Blakey

The Kidd Creek orebody is a massive, base metal deposit with widths up to 600 feet and a strike length of 2,200 feet. The orebody dips eastwards at 70° to 80° and is amenable to sub-level open stoping. Five distinct zones (Fig.1) based on structural wall rocks and ore type parameters occur within the orebody. These zones are: Zone 1 - Mainly copper stringer ore Zone 2 - Massive pyrite ore Zone 3 - Massive sphalerite and chalcopyrite Zones 4 and 5 - Are banded and variable in nature Compressive strengths vary from zone to zone with an average of 22,000 p.s.i. and highs of 40,000 p.s.i. The mine is developed from a ramp extending from surface to the 1600 foot level and a 24 foot diameter, 3050 foot vertical shaft with main levels at 400 foot intervals. Sub-levels at 100 foot vertical intervals are driven from the ramp. transverse and longitudinal pillars to support the crown pillar left under the open pit. The layout allows an opportunity to enlarge or reduce pillar sizes and also to introduce fill on any horizon should conditions warrant. It also offers a large number of operating stopes spread through the various ore zones giving good ore blending characteristics. All ore from the stopes is handled through drawpoints using Wagner ST8 scooptrams with an average one way haul length of 650 feet.

Jan 1, 1976

By Barun Gorain, Aparup Chattopadhyay

"Many double refractory gold deposits are characterized by the dominance of ""invisible gold"" (sub-microscopic gold) as solid solution or as colloidal-sized particles in different sulfides and other phases. These deposits are mainly composed of silicates and carbonates with moderate clay and mica content and with minor amount of sulfides and organic carbonaceous matters. The presence of highly preg-robbing and finely disseminated carbonaceous matter adversely affects gold recovery in leach circuits. Characterization of carbonaceous matters, commonly known as TCM and quantification of gold associated within these carbonaceous matters along with different sulfide and oxide phases is highly complex and challenging. Studies were initiated on various complex ore deposits and also on samples representing various process streams. This paper presents the development of a systematic approach to gold deportment studies using state-of-the-art mineralogy characterization techniques for quantification of invisible and visible metal contents in various species. The relevance of this mineralogy characterization to metallurgy will also be discussed in this paper."

Jan 1, 2014

By Arthur W. Ruff

The iron-ore beneficiation and shiploading facilities of the Marcona Mining Company are at San Nicolas Bay which is on the Peruvian coastal desert about two hundred and seventy miles south of Lima. The mines are at elevation of 2,500 ft. Crude ore is transported from the Mine primary crushers to the beneficiation plants by ten miles of overland belt conveyors. After the predominantly magnetic ore is reduced to minus 3/4 in. in the secondary crushing plant, the ore is ground by rod and ball mills and concentrated with magnetic separators. The concentrate slurry is pumped to a thickening and filtering installation for desliming and dewatering. Pelletizing is accomplished with a Lurgi and also a Dravo-Lurgi machine. Deep-water shiploading facilities are available close to the beneficiation plants. Figure 1 shows a flowsheet of the general operation. Pelletizing operations are scheduled 24 hours a day and 365 days per year. A maximum tonnage rate with a high percentage of operating time is necessary to produce the three and one half million tons per year required from the two pellet lines. Process control is a major responsibility and of primary concern to all Operating personnel. The particle size, moisture, and chemical composition of the filter cake must be closely controlled to get uniform high-grade pellets. Key points are sampled routinely and analyzed on a two-hour basis to provide the necessary structure and chemical data to maintain a superior final product. The iron content of the pellets is held between 65.3 and 65.8 percent with 4.0 percent Si02. Sulfur is below 0.04 percent and copper is below 0.02 percent in the finished pellet.

Jan 1, 1968

By K. A. Clark

A meeting between representatives of the Scientific and Industrial Research Council of Alberta and the Deputy Minister of Mines for Canada was held at Edmonton in May, 1929, for the purpose of formulating a co-operative plan for carrying forward studies in aid of the development of commercial methods for utilizing the bituminous sands of Alberta. It was agreed that to the Alberta Research Council should be allocated the general problem of investigation of the processes for the separating of bitumen from the sands, including studies of methods of emulsifying, dehydrating and otherwise preparing separated bitumen for industrial applications. It was further agreed that during the present year the work of the Alberta Research Council should be to continue its laboratory investigations of points of design of its separation plant; to further perfect its separation procedure; to recondition its existing separation plant at Dunvegan Yards, Edmonton, in the light of laboratory studies and to operate it for the purpose of demonstrating its efficiency; to carry on tests in emulsifying and dehydrating or otherwise preparing separated bitumen for industrial application; and on the basis of the experience gained in the operation of the preliminary plant at Dunvegan Yards to prepare and design and, as far as possible, to proceed with the erection of, a semi-commercial separation plant at a site to be chosen, probably at the bituminous sand deposits near McMurray, Alberta. This paper presents, in the main, a progress report of the carrying out of this programme.

Jan 1, 1929

By F. Dingwu

The latest technology and novel equipments in kaolin processing industry in China are described in this paper. Some typical experimental results are presented, which include laboratory-, pilot-or commercial-scale tests. The characteristics of kaolin processing technology are summarized, and the developing trends are indicated.

Jan 1, 1995

By E. A. Rychkun

Mining and environmental objectives have traditionally been in conflict. This conflict reflects a delicate balance between the need to spend money to protect the environment, and the need to save money by extracting minerals efficiently. In an increasing number of cases, profit margins diminish rapidly with new environmental regulations and reactionary measures. Forced cleanups and increasing restrictions are unwelcome expensive processes. A practical solution lies in planning rather than reacting. This requires the ability to precisely quantify and qualify environmentally sensitive problems by providing effective engineering tools to model, visualize and analyze subsurface conditions. Prevention of environmental conflicts, and effective cost control are both rooted in the mining company's ability to construct accurate models, monitor changes, assess contamination risks and to design effective remediation plan. This paper presents a case study where these issues are addresses through the application of a new and innovative technology.

Jan 1, 1993

By L. A. Grant

This paper describing the concentrator practice of the Montana Mines Corporation at Helena. Mont., is one of a series of articles on milling methods and costs being prepared by the United States Bureau of Mines. The Spring Hill mine and mill are located 4 miles south and west of Helena, Mont., near the head of Grizzly Gulch. The mine portal is on the east slope of the gulch, and the mill is directly opposite on the west slope. Grizzly Gulch is one of the tyro gulches which unite at the south end of Helena to form Last Chance Gulch, on which the main street of Helena is built.

Jan 1, 1931

By M. D. Amirova

Cyanide-free technology of complex copper-lead ores flotation may be improved through enlarged range of pH values, enhanced copper recovery into copper concentrates due to additional recovery of secondary copper sulfides, as well as through enhanced efficiency of lead sulfides depression in process of new flotation modifiers-based selective separation. Study of the effects of flotation modifier (of metal nature) on minerals surface conditions proved that the xanthate is practically not adsorbed on the galenite surfaces due to minerals hydrophilization. Joint effects of sodium sulfite and modifier enhance process conditions for intensive galenite depression and at the same time for effective chalcopyrite and chalcosine flotation within a large pH values range (from pH=8 to pH=10). Identified mechanisms carry inference that proposed chemical reagent treating method is very promising for selective copper-lead concentrates separation. Potential use of carbon-containing materials as zinc flotation modifier to enhancing zinc recovery in processes of lead-zinc ores treatment has been studied. In our flotation tests we used Shalkiya (South Kazakhstan) lead-zinc ores containing such impurities as carbon shales, which presence impedes the process of saleable concentrates production and gives rise to excessive consumption of flotation agents due to the xanthate adsorption on the carbon. Lead and zinc concentrates were produced by process stages as follows: ores milled to 95% Cl. -0.074 +0; lead and zinc roughing flotation and further recleaner and testing operations. Test flotation in open process cycle resulted in enhancing zinc recovery into zinc concentrates by 21.1% and increasing zinc content in zinc concentrates by 3.96% that evidences promising potentialities for use of carbon-containing products as additional zinc flotation modifier. Works were carried out under National Program 2003~2005 of fundamental researches ?Physical and Chemical Mechanisms of Interactions in Multicomponent Solid and Liquid Systems Specific for Integrated Processing of Complex Metal-Containing Minerals and Technogenic Raw Materials? and contractual Agreement 2005 Optimization of Production and Technology of Shalkiya Lead-Zinc Ores Processing at Kentau Dressing Works.

Jan 1, 2014

By The Staff

Introduction In this paper it is proposed to discuss briefly some of the problems confronting the management of a gold mine in choosing a method of milling to recover the gold from various classes of ore. In order to simplify the discussion, the more common types of gold ores are classified from a metallurgical point of view as follows: Class 1?A: Free-milling ores which require only relatively coarse crushing. B: Free-milling ores which require finer grinding to release the gold. Class 2?A: Gold ores which contain the gold partly in the flee state and partly associated with a small amount of iron sulphide, and which do not require fine grinding. B: Gold ores similar to 2A, but which require fine grinding. Class 3?A: Gold ores containing copper in quantities insufficient to interfere to a serious extent with cyanidation. Gold ores containing copper in sufficient quantity to interfere with cyanidation but in which a large proportion of the gold is in the free state, the remainder being chiefly associated with the copper mineral, chalcopyrite. Gold ores containing copper and other sulphides, such as pyrite, etc., in which the gold is principally associated with these sulphides.

Jan 1, 1931

By S. K. Nicol

Flotation, water-washing cyclones (hydrocyclones) and spiral concentrators are the three process units most commonly utilised in fine coal preparation. The results of testwork conducted on these three units will be presented and their performance and separation characteristics examined in detail. In particular, the dependence of the separation characteristics of each unit on particle size and the constraint this places on product quality (ash and sulphur levels) will be discussed. This dependence will be shown to be a critical criterion in the selection of fine coal circuits.

Jan 1, 1986

By T. Ueno

Naoshima Smelter & Refinery of Mitsubishi Materials Crop. commissioned a new Mitsubishi continuous copper smelter in May 1991. Process offgas volume of the conventional reverberatory furnace line, one of the previous smelters having been shut down, was very large and thus two acid plants had been operated. It was expected that the offgas volume would be reduced at the new smelter to about a half of the sum of those from previous two 1 smelters and the sulfur dioxide strength would be increased. So various alternatives were studied to minimize the operation cost. And it was decided to utilize both of the plants with minor modifications by diluting the gas either with air or with dilute gases. The acid plants now receive offgases from the new copper smelter, a sintering machine of a lead smelter and a decomposer of waste acid. The paper discusses plant design, operation, improvements and modifications realized in relation with the retrofitting of the copper smelter.

Jan 1, 1992

By J. A. Bradbury

N. A. Degerstrom, Inc. has constructed and operated a processing plant approximately five miles north of Soda Springs, Idaho for processing a byproduct phosphate treater dust from Monsanto's elemental phosphorus plant, also located in Soda Springs. The plant is designed to produce agricultural-grade phosphoric acid, gallium, and silver. The design capacity of the plant is 54.4t (60 st) of treater dust per day, which can produce 16,326t (18,000 st) of phosphoric acid, 6,600 kg of gallium, and 6,033 kg (194,000 oz.) of silver per year.

Jan 1, 1993

By M. Oliazadeh

Spodumene [LiAl(Si2O6)] is the most common and desirable economic lithium-bearing mineral due to its high lithium content. In Canada, there are several spodumene deposits at the development stage that have the potential to help narrow the forecast lithium supply gap stemming from the widespread acceptance and increasing use of electric vehicles. Spodumene processing can be conducted using Dense Media Separation (DMS), flotation or combination of both. If spodumene liberation is sufficient at coarse particle sizes, DMS can be used for primary lithium concentrate production and silicate gangue minerals rejection. If liberation is not sufficient, flotation is then the main processing route for spodumene concentration. Even in cases where DMS is a viable beneficiation option, flotation may still be required to process the DMS middlings and/or the undersize fraction which is outside the particle size range for DMS. Considering flotation as a technique for spodumene beneficiation, there are several alternatives including the use of mechanical flotation cells, column flotation cells, coarse particle flotation cells, and/or Staged Flotation Reactors (SFR), either alone or in combination. Ore sorting can be incorporated at the start of the spodumene flowsheet to remove gangue minerals, particularly amphibole and pyroxene in the early stages. The main objective of flowsheet development for hard rock lithium deposits is to evaluate the ability of these options to produce a spodumene concentrate with a concentrate grade above 6% Li2O, lithium recovery of above 80%, and with the minimum operating and capital cost. This paper aims to describe the various processing options available for the beneficiation of spodumene from hard rock deposits and compare the associated operating and capital costs for each.

The mining industry has generally been slow to apply ion exchange processes to hydrometallurgical applications even if ion exchange offers an ideal solution for a particular problem. Two notable exceptions are in gold and uranium recovery. The largest application of ion exchange in the metals processing industry has been the use of resin-in-pulp (RIP) for gold recovery as an alternative to activated carbon. Iron is a ubiquitous impurity in hydrometallurgical solutions. In many cases, bulk removal of iron from the process solutions is accomplished by precipitation. However, precipitation for iron control is often accompanied by losses of base metals by co-precipitation. Increasingly, the option of ion exchange for removal of smaller amounts of iron from process solutions has been favoured. A number of applications have been developed and proven at the commercial scale for the removal/control of iron from a range of metal processing solutions. This paper provides an overview of the application of ion exchange for iron removal from a range of metal processing operations, including Cu, Ni and Co solutions. A number of case studies are provided which review operational and resin regeneration strategies and the impact upon the commercial operation of metal processing with improved iron control.

Jan 1, 2006

By W. K. Connor, O&apos

The Bureau of Mines has conducted beneficiation, carbothermic reduction, and leaching tests of Mn oxide ores as part of its evaluation of the Mn and Co resources of the West- Central Arkansas District. The major Mn oxides in the ore include cryptomelane, psilomelane, pyrolusite, and lithiophorite. Cobalt is contained within the Mn oxides. Nonbeneficiated ore was reduced at 800' C with coal and leached in ammonium sulfate and ammonium carbonate leach liquors. Ore concentrates were calcined at 600" C prior to reduction under the same conditions as the raw ore. Head analyses reported up to 21 ptt Mn and 0.11 pct Co. Extractions of 70 to 90 pct Mn and 40 to 60 pct Co were achieved.

Jan 1, 1992

By B. K. Parekh

Large reserves of coal pond fines are found in the Illinois Basin-over 40 million tons in Western Kentucky, over 65 million tons in Southern Illinois, and over 35 million tons in Southern Indiana. If these fines are used to produce coal-water slurry (CWS), fuel costs, NOx. emissions, and pond closure costs can be reduced. Coal fines from this region that are used to produce CWS for co-fire or re-burn may require processing, however, to attain proper particle size distribution and fuel quality. To evaluate the effectiveness of using coal cleaning technologies to control these CWS quality parameters, a simple flowsheet for recovering and processing coal pond fines was designed and tested. Coal fines processing consisted of using classifying cyclones to size at nominal minus 200 mesh, cleaning the classifying cyclone underflow using spirals, and cleaning the overflow using column froth flotation. Ash content of the dean coal from the spiral was reduced to about 10 percent, which is satisfactory to use for CWS co-firing in a cyclone-fired boiler. The clean coal from column flotation may be used for re-burn in a cyclone-fired boiler or as co-fire fuel in a wall-fired or tangentially-fired boiler. Heating value recovery during laboratory-scale, pilot-scale, and commercial-scale coal cleaning testing was about 80 percent.

Jan 1, 1998

By T. Ueno

Naoshima Smelter & Refinery of Mitsubishi Materials Crop. commissioned a new Mitsubishi continuous copper smelter in May 1991. Process offgas volume of the conventional reverberatory furnace line, one of the previous smelters having been shut down, was very large and thus two acid plants had been operated. It was expected that the offgas volume would, be reduced at the new smelter to about a half of the sum of those from previous two smelters and the sulfur dioxide strength would be increased. So various alternatives were studied to minimize the operation cost. And it was decided to utilize both of the plants with minor modifications by diluting the gas either with air or with dilute gases. The acid plants now receive off gases from the new copper smelter, a sintering machine of a lead smelter and a decomposer of waste acid. The paper discusses plant design, operation, improvements and modifications realized in relation with the retrofitting of the copper smelter.

Jan 1, 1992

By R. E. Hamilton

"The requirements for effective optimization of a mineral dressing operation are discussed, with specific reference to a flotation system . Also considered are the relation-ships between automatic control and optimization pro-grams. Variables are classified into the following groups, and the significance of the classification is discussed: (a) Directly measurable (b) Directly manipulable (c) Uncontrollable (d) Calculable from measurable variables (e) Affected by changes in manipulable or uncontrol-lable variables. New sensors for measuring variables not normally measured are described."

Jan 1, 1967

By G. H. K. Pearse, R. P. Taylor

The Big Whopper, one of only four giant economic rare metal pegmatites worldwide, is set to become a producer of the highly valued lithium mineral petalite (LiAlSi4O10) used in glass, ceramics and the specialty glass-ceramics familiar as Corningware® and the new ceramic stovetops. The deposit has a strike length of 1.5 km, a width of up to 80 m and a resource, open in all directions, of 11.6 Mt, grading 25% petalite. It is amenable to open pit mining and Avalon Ventures Ltd. holds a patent on a flotation process that produces an exceptional quality petalite product. The project will also produce: superb quality Na-feldspar which, too, finds use in glass and ceramics; the unusual Rb- K-feldspar for high voltage porcelain insulators; tantalum, in high demand for electronics; lepidolite, an ore of rubidium; and mica and tin. A positive prefeasibility study has been completed and it remains only to undertake bulk sampling and a full feasibility study.

Jan 1, 2001