Search Documents

By Marc E. Orman, Mark E. Smith

Regulatory and environmental concerns continue to broaden the range of mine wastes that must be capped with low permeabili­ty liner systems at closure. The mining industry has been a leader in developing liner technology for leach pads and tailings impoundments, but it is a newcomer to cap designs. Closure of waste piles, leach heaps and tailings require special design con­siderations. Factos such as differential settlement, surface ero­sion, veneer stability, vegetation and burrowing animals must be considered.

Jan 1, 1996

By P. Zhang, S. Al-Thyabat

"Phosphate rock contains traces of rare earth elements (REEs) and can be a secondary source of these critical materials as large tonnages of phosphate rock are mined annually. Attention has mostly focused on the extraction of REEs from phosphogypsum, which contains more than 70 percent of the REEs reporting to phosphate concentrate, with only limited work conducted on REE extraction from sand tailings and slime even though they account for 16 percent and 15 percent, respectively, of REEs mined with phosphate matrix.In this work, phosphate flotation tailings were upgraded by gravity separation and froth flotation. Gravity separation was conducted using a laboratory shaking table, while flotation was conducted in a Denver D-12 flotation cell. The concentrated tailings were then leached by nitric acid followed by REE extraction with solvent and ion-exchange resin.The sand tailings were assayed as having 2.6 percent phosphate (P2O5 ) and 198.1 µg/g REEs. It was found that the shaking table could produce tailing concentrate assayed as having 8.6 percent P2O5 and 616 µg/g REEs but with only 20 percent REE recovery, while the froth flotation produced froth concentrate assayed as having 8.1 percent P2O5 and 368.2 µg/g REEs with 63.5 percent REE recovery. Leaching the flotation concentrate with 5.2 M (25 percent) nitric acid followed by extraction with solvent and ion-exchange resin yielded precipitates with REE contents of 0.926 and 0.314 percent, respectively, compared with 0.716 and 0.213 percent when table concentrate was used.IntroductionRare earth elements (REEs) consist of a group of 17 elements: the 15 lanthanides along with yttrium (Y) and scandium (Sc). They are rare not because of their scarcity in the Earth’s crust but because they are rarely found in economic and mineable deposits. REEs are called “seeds of technology” because of their importance to some critical technological industries such as renewable energy, hybrid cars, electronics and batteries. On average, an electric car or a hybrid car contains about 10 kg of REEs (Grasso, 2012; Radhika et al., 2011).REEs are usually categorized into light (LREE) and heavy (HREE). LREEs consist of lanthanum (La), cerium (Ce), praseodymium (Pr), neodymium (Nd), promethium (Pr), samarium (Sm), europium (Eu), gadolinium (Gd) and scandium (Sc), while HREEs consist of terbium (Tb), dysprosium (Dy), holmium (Ho), erbium (Er), thulium (Tm), ytterbium (Yb), lutetium (Lu) and yttrium (Y). About 200 minerals contain traces of REEs, but only three are considered economically significant: bastnasite, with the formula La,Ce(CO3)F; monazite, with the formula(Ce,La,Nd,Th)PO4; and xenotime, with the formulaYPO4 (Jordens, Cheng and Waters, 2013)."

Jan 1, 2016

By Wiebe Boomsma

This is a framework study financed by the Maritime Innovation Programme of The Netherlands and several institutions actively involved in the research of the environmental impact of deep sea mining; IHC Mining, MTI Holland, Delft University of Technology, NIOZ, IMARES, Boskalis Westminster, AllSeas and TNO. For this framework study the following mining activities have been identified to be relevant to assess the ecological impact of a deep sea mining operation: a) excavation, b) tailings return, c) vertical transport, d) vessel operations, e) ore transport and f) general operations. For this paper, only one mining activity has been selected as an example for the assessment of ecological effects. This is one of the main activities introduced by the new technology envisaged for developing deep sea mining: tailings return.

Sep 14, 2011

By R. Bruce Ferguson

"The Kettle River Operation of Echo Bay Minerals Company is located about thirty kilometers north of the town of Republic in northeastern Washington State. In tum, Republic is about a hundred and seventy kilometers north and a little west of the city of Spokane, Washington. It is also about fifty kilometers south of the town of Grand Forks, BC, Canada. At this time it is the only gold mining and milling operation in the State.Tailings are stored in a double lined, zero discharge facility. It became evident in mid 1996 that the rate of free water accumulation in the tailings pond was going to result in the level in the pond reaching its permitted freeboard elevation long before the solids plus pore water capacity was reached.We then embarked on a mission to manage tailings pond water on several fronts: reduce fresh water usage in the process, divert spring seeps and surface runoff and install a system to enhance evaporation.IntroductionThe Republic area is an historic gold mining district. Hecla operated its Republic unit from 1892 until closure in 1994. The Kettle River Operation processing plant is located in the San Poi! river valley at an elevation of just under a thousand meters. The facility consists of a ninety thousand ton ore storage pad as the mines are remote and truck haulage is subject to interruption due to weather and road restrictions, jaw and cone crushing with screening, rod and ball milling to an eighty percent passing size of seventy five microns. This is followed by preaeration with high purity oxygen supplied by a vacuum pressure swing adsorption plant plus lead nitrate addition to achieve passivation of the sulfide mineralization such as chalcopyrite, pyrite and pyrrhotite. Conventional cyanide leaching and carbon in pulp adsorption completes the loop. Tailings are treated with air/S02 to achieve cyanide destruction. Plant capacity is 1,815 tons per day. Our license requires that there be no detectable free cyanide in the tailings pond water and a maximum of forty parts per million weak acid dissociable cyanide. The operation started in 1989 with production from the Overlook Mine located about five kilometers further up the same valley at an elevation of twelve hundred meters, hence the location of the mill. Current mine production comes from Lamefoot in the Curlew Lake valley, about ten kilometers distant, and K2 in the Kettle River valley about fifty kilometers away. Both are at an elevation of about 800 meters. Lamefoot produces 1,360 tons per day and K2, 455. Both are underground operations."

Jan 1, 1998

By James Charles McHardy

During 1980-2000, the Florida Phosphate industry will deplete its Central Florida Polk County reserves. As a result, new mines will be built in the ?so-called? Southern Florida Reserve areas. These new mines will require new mining, beneficiation and tailings disposal technologies in that the southern reserves have different characteristics than have been encountered in the Central Florida deposits furthermore, government regulations will necessitate the development of new tailings and clay disposal methods. This paper reviews these challenges for the phosphate industry and how these opportunities can be expected to effect plant design and plant operating practices.

Jan 1, 1981

By William E. Mead

Although this paper has been entitled "Design of Embankments for Tailings Ponds and Waste Dumps," a better title might have been "Site Selection and Design Planning for Tailings Ponds and Waste Dumps," The procedures normally followed in performing the engineering calculations based upon the measured soil properties will not be detailed. Instead, we shall look at the subject in broader perspective which considers the environmental factors and the fundamental design principles. Disposal of waste materials left from the extraction and processing of mineral deposits has become, in recent years, an important engineering consideration for mine and mill operators. Land occupancy and land values almost everywhere are increasing at a rapid rate. So is the size of mine and mill waste dumps, thanks to our advancing technology in mineral beneficiation. Mining companies are being pressured to "clean up" their operations, both literally and in a safety hazard sense. Once, long ago, the miner could use any convenient location to get rid of his mine waste and mill tailings without being concerned over possible infringement on the rights and well-being of the public. Today, however, he must pay close attention to these matters if he wishes to avoid liability suits and the unfavorable reaction of civic groups as well as local and regional government. Most operators keenly sense their increased responsibility, not only because they are legally vulnerable, but because they realize the necessity for sharing space harmoniously with the rest of society.

Jan 1, 1967

By G. L. Bloomsburg, E. G. Zahl

INTRODUCTION During the past decade, disposal of mine and mill waste material has become an increasingly important issue. Problems of structural stability and seepage effects on stability have been well addressed, and significant technological advances have been achieved [(1-4)]. The primary problem currently facing industry in the waste disposal area is environmental protection. The greatest environmental concern is over the amount of seepage or leachate entering the ground or surface water systems. Methods to determine the quantity of water seeping from a tailings pond have also been covered in the literature [(5-23)]. However, much further work is necessary to fully implement these techniques to evaluate tailings pond performance and accurately predict the various influences of disposal management on seepage from mill tailings. This study is an effort to develop those necessary techniques. The partially saturated method of analysis which is discussed here is applicable to most situations involving seepage from waste piles. In a conventional type of tailings pond, a slime layer is ordinarily built up under the ponded area. This material will consolidate slowly from capillary pressures and the weight of material deposited above it. In situations where this consolidation results in a slime layer of lower permeability than the native foundation soil, a partially saturated flow condition will usually exist in the native soil. This will result in a smaller quantity of water entering the ground-water system than would be predicted by saturated flow analysis. The finite-element program used in this study was originally developed by Neuman [(17)] and is called UNSAT2. The program will analyze problems of saturated or unsaturated, steady or nonsteady flow and can be used with a variety of boundary conditions such as constant flux, constant pressure, maximum flux, minimum pressure, and with infiltration, evaporation, and seepage surfaces. The maximum conditions are controlled by exterior factors such as atmospheric conditions; but the actual flow in the porous media is determined by properties of the porous media. In this test, the computer code was used

Jan 1, 1980

By N. Rocco, G. Johnson

Implementation of post-closure draindown estimates for tailings facilities are important predictive tools for reclamation planning and often influence jurisdictional bonding. Simplified estimates of draindown have been proposed in the past but these methods are not able to capture many of the site-specific nuances as well as operational and material parameters that influence robust draindown estimates. This paper discusses an iterative approach that relies on unsaturated flow models to predict draindown rates and associated pond inventory water balances that track inputs into underdrain pond systems, solution storage volumes, implementation of active evaporation, and necessary recirculation of solution back to the tailings facilities. Specific design criteria such as climate, facility geometry, material properties, and initial conditions, as well as active closure operational considerations that can influence draindown estimate will be discussed. Concepts presented will be valuable for operators, designers, and regulators to guide closure planning and predictive analytical analyses that support draindown estimates.

Mar 2, 2022

By G. V. Sullivan

The Federal Bureau of Mines examined tailings samples from 13 western copper operations to determine the potential for recovering rutile. Results showed that six of the samples contained sufficient liberated titania to be considered potential sources. One sample contained 0.75 percent Ti02 or 0.40 percent liberated rutile. Batch flotation studies developed a procedure that recovered 70 percent of the liberated rutile at a grade of 34.7 percent TiO2. Sulfuric acid leaching studies on 12 of the samples dissolved 100 to 2,200 grams Cu per ton of tailings; leaching of the slimes showed slightly more copper was dissolved, 1,800 to 3,300 grams Cu per ton of minus lo-micrometer material. Bulk sulfide flotation of nine of the samples resulted in concentrates that contained 0.38 to 2.0 percent Cu and 0.7 to 2.1 and 6.9 to 42.9 grams per ton Au and Ag, respectively.

Jan 1, 1981

By Ian Hutchison, Ted Sluder, Jack Caldwell, Don Moore

Introduction The Cannon mine at Wenatchee, WA has recently been brought into operation to recover gold from the sandstones of the Swauk formation. The mine is a joint venture between Asamera Minerals (US) Inc. and Breakwater Resources. A tailings impoundment was constructed to impound 2.7 to 3.6 Mt (3 to 4 million st) of tailings at 1.8 kt/a (2000 stpd) over about five years. This paper describes the design and construction of the impoundment. In particular, it describes the 100 m (300 ft) high earthfill embankment that is the main feature of the facility. Project environment The project is located on the outskirts of Wenatchee, a town of about 40,000 people. The town is situated on the flat alluvial terraces beside the Columbia River. The Cascade Mountains rise from the terraces in a series of ridges and valleys. The mine is at the foot of the Cascades. The tailings impoundment is in one of the steep valleys. The climate is mild and dry (Table 1). Site selection Twelve alternative sites within a 16-km (10-mile) radius of the mine were examined. Decision making theory was used to select the most suitable site. Advantages of the chosen site include its proximity to the mine and its low visibility from points of common public access. Also, the area was already heavily impacted by an existing silica quarry. The major disadvantage of the site is the need to pump tailings over a distance of 1.5 km (1 mile) and against a static head of 200 m (655 ft). Also, it is located in a gulch just upstream from the town of Wenatchee. Site geology The impoundment is generally underlain by interbedded sandstones and siltstones. The siltstones are often shattered. The sandstones are often friable. Both rock types are extensively jointed. Some isolated faulting of the sediments occurred before the area was covered with basalt flows. About 10,000 years ago, at the end of the ice age, the basalts were covered by 3 to 10 m (10 to 33 ft) of wind blown loess - a fine sandy clay and silt. River deposits filled the base of the valley to depths between 5 and 25 m (16 and 82 ft). Under the main part of the embankment, these materials were removed to expose bedrock. Ground water flow is generally through the more permeable layers. The permanent water table is about 5 m (16 ft) beneath the ground surface. Project and impoundment layout Figure 1 shows the layout of the mine, the mill, and the tailings impoundment. The tailings deliv-

Jan 8, 1986

The issue of fine coal and tailings dewatering has become of increasing concern to many coal preparation operators, both in Australia and overseas due to a variety of factors. Increasing mechanisation and mining of thinner seams over the past decades has resulted in an increasing amount of fines generation while increasing international trade in coal and tighter environmental constraints on tailings disposal have resulted in the production of these same fines to be an increasing problem. However, technology to date has not always been able to supply a cost-effective solution to the handling of these fines in an efficient and environmentally benign manner. This paper will review the key issues associated with the dewatering of fine coal and tailings, will describe the major current practices and constraints, and finally will indicate alternative technologies that may have to be considered in the near future. For the purpose of this paper, "fine" coal is described as that material less than 0.5 mm in diameter (as this is the most common cutpoint between various plant circuits in Australian practice), although the technological constraints are very much dependent upon the fraction less than 45 micron. The amount of minus 0.5 mm material fed to plants varies, depending upon the type of coal and mining operation, but in Australia may range from less than ten per cent to greater than 30 per cent of the feed in higher rank coals.

Jan 1, 1991

By S. Gan, E. van Niekerk, L. Birrell, D. Robbertze, L. Ncubi, B. Zhao

Quality assurance and quality control (or QAQC) plays a key role in safeguarding the level of confidence of the data generated during mineral exploration and mine development, and is also part of the reporting code requirements for resource estimation and reporting, as well as mining investment. Implementation of good policies and working protocols in quality management will result in the generation of reliable information, which is critical for decision-making on the future of the mining project. The use of certified reference materials, i.e., standard, blank, and duplicate samples, proves effective and efficient for ensuring the level of data confidence in terms of precision, accuracy, and sample contamination. This is well demonstrated by the practice of QC in the exploration programme for the chrysotile tailings storage facilities of Havelock Mine, using 1254 samples from 53 drill-holes. Different statistical tools were applied to analyse the assay results from these samples. The outcome substantiates that the QC practice established during the Havelock exploration project is aligned to best practice guidelines in the industry. The resource delineated indicates that the tailings material at Havelock could potentially become a significant source of supply to the global magnesium market.

Jul 2, 2022

Paste Thickening of Tailings at the Clermont Coal Preparation Plant

Sep 13, 2010

By A. S. Malicsi, R. J. Lipp, I. Iwasaki

A loch-grade copper-nickel deposit, with an estimated 4.6 Gt (5 billion st) and average analyses of 0.6% copper, 0.2% nickel, occurs in northeastern Minnesota. In addition to copper, nickel, cobalt, and precious metals, the Duluth gabbro contains magnetite, ilmenite, olivine, plagioclase, and biotite. It u estimated that flotation tailings that would be produced by a concentrator of optimal size to sustain a smelter would amount to 20 Mt/a (22 million stpy). The flotation tailings, having already been ground, warrant a closer examination for recovery and use of potential byproducts. Residual sulfide minerals and fibrous minerals may also be isolated and treated separately for useful purposes or for disposal in an environmentally acceptable manner. Two flowsheets were developed; one involving preconcentration by low- and high-intensity magnetic separation and another involving preconcentration by gravity concentration. Concentration methods for recovering and purifying individual byproduct minerals were investigated. From their chemical, physical, and mineralogical characteristics, the potential areas of application and marketabilities of each product fraction were surveyed.

Jan 1, 1985

By Georgia J. Lysay

The Kemess Mine tailings impoundment is retained behind an earthfill and rockfill dam that, when complete, will measure about 140 m in height with a crest length in excess of 1 km. Due to weak foundation conditions, the dam must be raised at a very flat downstream slope approaching 7H:1V. This requires an enormous volume of fill to construct the downstream shell of the dam, which has a low permeability clayey till core and is raised via the centerline construction method. For the initial years of annual dam raising, from 1996 through 2002, the downstream shell of the dam was constructed with non acid generating waste rock from the open pit, 7 km distant and requiring an uphill haul with obvious cost implications. To reduce costs, and to reduce waste haulage constraints on mining schedules, feasibility studies were initiated for raising of the downstream shell using cycloned tailings sand as opposed to open pit waste. This required inclusion of flotation cells for removal of residual sulphides from the tailings to produce the non acid generating product mandated for the downstream shell of the dam. These studies were positive, and cycloned sand construction was initiated in December of 2002. This paper describes the experience gained with cycloned sand construction for the dam. Unique aspects include environmental controls given the sulphide-bearing ores, preparation of the existing shell of the dam for subsequent placement of hydraulically placed cycloned tailings sand, on-dam settling ponds, water management issues, reclamation of the sand dam for erosion control commensurate with the wet climate, and use of the system to construct an above-water beach of non acid generating tailings to increase the closure security of the structure. A particularly unique aspect of the Kemess experience is hydraulic fill operations extending throughout the coldest winter months, as compared to other operations where such placement has traditionally been considered non-viable through the winter months

May 1, 2007

By Luzheng Chen

Pulsating high-gradient magnetic separation (PHGMS) of fine hematite from tailings was studied using a pilot PHGMS separator to investigate the possibility of its application in industry. The results of this investigation indicate that PHGMS is effective for recovering fine hematite from the tailings and greatly improved the separation performance compared with the conventional high-gradient magnetic separation at the same conditions. By applying the pilot separator with a 1-mm rod matrix to a tailings containing 28.76% Fe, a concentrate assaying 54.35% Fe with 35.89% recovery was achieved. It was found that the separation performance of the pilot separator closely correlates with the main pulsating parameters, i.e., pulsating stroke and frequency. It was also found that a change in the wire diameter of the rod matrix from 2 to 1 mm causes a weak drop in concentrate grade but results in a considerable rise in recovery. This finding proves that the improved performance achieved by the pilot separator is attributed to the pulsating of slurry and to the use of a 1-mm rod matrix. When the first commercial SLon-2500 PHGMS separator with a 1-mm rod matrix was applied to recover fine hematite from the tailings, the results duplicated those achieved with the pilot PHGMS separator.

Jan 1, 2009

By W. R. Bruce, G. W. Hodgson, K. A. Clark

"IntroductionANY PLANT processing mined Athabaska oil •sand for the recovery of oil produces, as a waste material, about one ton of sand for every barrel of oil recovered. A disposal problem of major proportions is thus indicated. For a 100,000-barrel per day plant, provision must be made for moving .about 4,000 tons of sand per hour on a continuous basis to a tailings dump at least several thousand feet removed from the plant site.Of the many known ways of conveying solids on .a large scale, the hydraulic pipeline transfer method is becoming increasingly important because of convenience and economy of operation. It has been in use for many years in mill operations at metalliferrous mines for the disposal of tailings and as such was a natural outgrowth of •hydraulic sluicing (3). Pipeline transportation of mill concentrates has been adopted recently ( 1), wherein high-density solids are moved several miles by hydraulic pipeline. The flotation power of the water suspending the solids may be increased 'by addition of magnetite for the handling of ore in pipelines (8). Low-density solids such as coal have received considerable study for low-cost pipe-lining (2) and a successful operation with coal has been carried out in England with indications of considerable savings over other methods of transportation (9). Dredge operations are based on pipeline transportation for the dredged sol-ids, and the scale of pipelining there .has involved pipe sizes as large as 32-inch (6). However, the tendency has been to regard the pumping of solids in water merely as a simple method of transportation and little consideration has been given in the published literature to study of the most economical modes of operating .a pipeline."

Jan 1, 1952

By F. F. Peng, Z. Lu

Employing a combination of two types of polyelcctrolyte might become necessary to enhance both the settling rate of the flocs and the water clarity of a fine-particle suspension in a high-capacity thickening process. The sequence of addition, mixing, type and dosage of polymer all affect the overall performance and capacity of a thickening process. For the sedimentation of copper flotation tailings, the cylinder test results showed that two different techniques may be used to achieve the required performance, i.e., a high settling rate of the flocs and the deisired underflow density and overflow water clarity. The required performance can be achieved by either adjusting the pH prior to anionic polyelectrolvte flocculation or using a combination of polymer flocculant and coagulant (dual-polymer system). The dynamic thickening test results showed that only the approach using a dualpolymer system is capable of meeting the required performance. The effects of polvelectrolvte dosage, the sequence and numbers of polyelectrolyte addition, the feed concentration, the bed level and the rake speed on the settling rate, underflow percent solids and water clarity were studied in cylinder tests and in a laboratory dynamic thickening unit. The dynamic test is especially valuable in evaluating the addition and mixing of polymers. The results were evaluated quantitatively using total suspended solids in supernatant, underflow density and capacity per unit of settling area per unit of time. The objective of this study was to quantify and explain some of the parameters involved in the sedimentation of copper flotation tailings.

Jan 1, 1999

By E. Mpoloka

Debswana together with ADP as their design partner have embarked on an RDP project at Jwaneng Mine. The objective of the project is to install a 2 million ton per annum mineral processing plant that will fast track the recovery of diamonds from the Debswana tailings resource to ensure maximum return on investment for the company. Due to the prevailing economic conditions Debswana has had to review the way they used to build plants in the past and consider simple, fast and effective ways of doing things. The rapid deployment plant concept is therefore the most suitable means of achieving this objective. Debswana is also considering an operating partner who will operate far more efficiently and cheaply compared to the larger more cumbersome and less agile Debswana.

Jan 1, 2010

By Kenneth L. Myers

The net balance of the inflow and outflow of water in a tailings storage facility has major economic implications in any large mining and milling operation. In a net precipitation environment it can control the ultimate size and storage capacity of a facility or dictate the need for an expensive treatment and discharge program. In a net evaporation environment it can control the extent of the water rights acquisitions required for makeup water and dictate the number and size of expensive wells and pumping and delivery systems. The elements considered in a water balance analysis include the anticipated production rate, the water content of the slurry used to deliver the tailings, inflow from precipitation and snowmelt, and losses from evaporation and seepage. The mine can exert significant control over only one of these elements: the production rate. All others are subject to considerable uncertainty from month to month and year to year. The traditional approach is to analyze in a spreadsheet environment by making simplifying assumptions and using monthly mean or "average" values for precipitation inflows and evaporation losses. Often the analysis will be repeated with values subjectively assigned to represent a "wet" year or "dry'' year. The probabilistic approach uses the same basic spreadsheet model in conjunction with a probabilistic simulation add-in program allowing probability distributions to be substituted for any of the deterministic variables. The resulting analysis shows the full range of variation possible for each parameter of interest (i.e., available return water, makeup water required, storage, seepage losses) and estimates the exceedance probabilities for each. The potential uses and advantages of the probabilistic approach are discussed.

Jan 1, 1992