Search Documents

By Santiago Gómez, Pablo Segarra, José A. Sanchidrián

In-hole detonation pressure measurements are unusual in the production environment of a mining operation, partly owing to the hostile conditions to which recording equipment and pertinent probes must be subjected and, partly by the constraints of the production cycle. In recent decades, detonation pressure measurement techniques have been developed using low carbon resistors (LCR)-based gauges. They are cheap, relatively easy-to-operate, robust and with a high percentage of success in both open-pit and underground mining. Detonation pressure measurements are extremely important when carrying out numerical modelling to simulate explosive induced vibrations, since simulation results are highly dependent on the pressure-time history applied on the blasthole wall. Analytical equations have typically been used to model the pressure-time history; however, they usually do not adequately represent the behaviour of the explosive in terms of: peak pressure reached, rise time, mean frequency, decay and shape of the signal. Experimental records may be directly used instead of utilizing synthetic signals if they are available. In this work, (LCR)-based gauges are used to measure detonation pressure inside a production blasthole. The operation principle of the gauges utilized and the instrumentation layout is described in detail. A flexible resolution USB oscilloscope with high sampling rate has been used to catch the elusive pressure peak event. Measurements were carried out in production blasts fired with ANFO (0.86 g/cm3) in an underground mine––this also includes velocity of detonation (VOD) records––. A procedure based on the shock impedance matching has been developed to calculate the detonation pressure due to the characteristics of the gauges prevent its direct measurement. Detonation pressures obtained range from 1.71 to 2.97 GPa (248.01 to 430.76 ksi) which are in line with pressures calculated from the VOD records. Mean frequency and rise time analysis shows that 2 of 3 signals cannot be described using typical analytical equations.

Feb 6, 2023

By Behrooz Abbasi, Seyedsaeid Ahmadvand, Thom Seal, Babak Azarfar, Bryan Ulrich

Hydro-Jex® is a new enhanced method for heap leach treatment with significantly higher mineral recovery. In this case study at the Los Filos Mine in Mexico, the Hydro-Jex operation is evaluated for heap leach stability. This is pursued by numerical modeling of the heap leach pad stability and well monitoring of the phreatic surface before and after the Hydro-Jex operation. Experimental and numerical results both indicate an improvement in mineral processing under the influence of Hydro-Jex. Numerical results show an insignificant decrease and a significant increase in stability during and after Hydro-Jex injection application, respectively. The integrity of the liner is maintained in both cases. The zonal injection pressure, operationally below the overburden pressure, is found to be negligible compared with the dimensionality of the heap, and stability of the structure is not exposed to any significant risk, even up to 25%above overburden pressure. Furthermore, heap leach factor of safety increases after Hydro-Jex application. This is attributed to breakdown of the water solution build-up and thus a decrease in the phreatic surface depth below the top of the pad. It is suggested that injection wells be drilled, based on thorough geophysical data, in locations where overcompaction of heap material results in water solution build-up and pore pressure enhancement. Compared with traditional heap leaching, the Hydro-Jex technique not only expedites mineral processing by increasing chemical kinetics extraction but also increases the stability of the heap by unclogging drains.

Jun 29, 2020

By Charles E. Heinrichs

IN the last decade one of our oldest and largest non-metallic metallic mineral industries has been the subject of persistent technical research, the results of which are another example of the benefits following the systematic application of scientific principles. The consequent improvement in the technique of phosphate recovery represents the greatest material advance in the industry since the discovery of phosphate in Florida in 1881. Moreover, these successes have stimulated interest and development in numerous other nonmetallic industries. Strange as it may seem, and despite the fact that the phosphate deposits of Giles County, Tennessee, together with those of Polk and Hillsborough Counties, Florida, have yielded more than 50,000,000 long tons in the last twenty years, the mineralogy of phosphates has been given scarcely any space in our technical literature. For many years it was the general consensus that these so-called phosphate rocks represented a physical mixture composed principally of tri-calcium phosphate, together with smaller quantities of calcium carbonate, calcium fluoride, iron phosphate, aluminum phosphate and other less important constituents. More recent investigations, however, led to the conclusion that these phosphates really represent a complex mineral in which calcium, iron, aluminum, phosphorus pentoxide, carbon dioxide, and fluorine all form a definite part of the molecule. Colony, after a careful study, utilizing chemical, microscopic, and X-ray diffraction methods, reported that American phosphates consist principally of calcium-carbono-phosphate of the staffalite type.

Jan 1, 1933

By J. Seiter, S. Cox, E. Kim

Mining has always been among the most hazardous of occupations, and with the increasing demand for coal and minerals, safety in mines assumes even greater importance. Worldwide, underground miners are being exposed to noise and respirable dust hazards associated with roof bolt drilling. These hazards are now being understood to cause irreparable damage to the health of miners. The objective of this research was to discover if a polycrystalline diamond compact (PDC) drill bit generates less respirable dust and hazardous noise than a competing tungsten carbide (WC) bit in dry vacuum drilling. In order to control the drill parameters the drilling tests were conducted in a laboratory setting. The results were obtained by determining the quantities of dust and noise generated using each drill bit and analyzing those levels, using monitoring devices and software to collect the data. This paper includes information on the experimental setup, equipment used, drilling parameters, and data collected. Our results indicate that PDC bits produce significantly less noise and dust than WC bits. Our findings can contribute to improving the working conditions of rock bolter operators by reducing noise and dust generation.

Jan 1, 2014

By Hamid Mazouz, Mohammed Hakkar, Rim Jouraiphy, Fatima Ezzahra Arhouni, Ahmed Mahrou, Aziz Boukhair, Mohammed Fahad

The wet process is the most commonly used worldwide for phosphoric acid (PA) production, in which phosphate rock (PR) is reacted with strong acid mainly sulfuric acid. This work aims on studying the rare earth elements (REEs) distribution during the production of phosphoric acid using different qualities of phosphate through various industrial technologies. At the onset of this work, the process started with 12 samples of PR, PA, and phosphogypsum (PG) being taken simultaneously from two different Moroccan basins (Ouled Abdoun mine represented by K09 and Gantour mine depicted by G10, G20, BG) and various production lines at two processing platforms (Jorf Lasfar and Safi). Afterward, collected samples were prepared and analyzed for REE characterization using an inductively coupled plasma mass spectrometry (ICP-MS). Based on the analysis results, a transfer factor ( TFX) was introduced with the aim of gauging the REE distribution between PA and PG. The results showed that the total concentration of REEs in different phosphate qualities ranged from 411 to 631 ppm; the major part of this concentration was attributed to the four elements: Y, La, Ce, and Nd which constitute more than 77%. The REE distribution between PA and PG depends on neither the phosphate quality nor the industrial technology used since that the distribution results showed that 55 up to 66% of the initial REEs in phosphate rock ended up in the PG. The behavior of each REE was common except for the element scandium, which transferred mainly to the phosphoric acid.

Nov 3, 2021

By F. S. Hoseinian, D. Deglon, L. leal Filho, M. Safari, T. C. Souza Pinto

This paper investigates the effect of chemical and physical operational parameters on the reverse flotation of Timbopeba itabirite iron ore in a pilot-scale pneumatic flotation cell. Operational parameters include collector and depressant dosages, feed rate, superficial gas velocity and solids concentration. Results show that increasing collector dosage results in an increase in quartz recovery, particularly for the coarser quartz where recovery increases by nearly 30%. Increasing depressant dosage results in a decrease in both quartz recovery and hematite loss, for the coarser hematite particles. Increasing the feed rate has no effect on quartz recovery or hematite loss, suggesting that the pneumatic flotation cell is not residence time constrained. Increasing the superficial gas velocity results in an increase in quartz recovery to an optimum at a Jg of around 0.6 cm/s after which it decreases significantly, particularly for the coarser particles where recovery decreases by as much as 50%. Decreasing the solids concentration does not affect quartz recovery but results in significant decreases in hematite loss. Here, fine and coarse hematite loss decreases from around 25% to 12% and 10% to 2% respectively. Superficial gas velocity and solids concentration are operating parameters which have the largest effect on the flotation performance of the pneumatic flotation cell. Results suggest that this flotation cell should be operated at relatively low superficial gas velocities and solids concentrations. However, these are pilot-scale findings and would need to be tested at an industrial-scale where different operating conditions may be optimal. Keywords: Operational parameters, reverse froth flotation; entrainment; iron ore

Jan 1, 2020

By M. J. Latva-Kokko, CA Snyders, J. R. Peltola, M. K. Kostiainen

It is well known that carbon management is essential for minimising soluble gold losses in carbonin- leach (CIL) and carbon-in-pulp (CIP) circuits. Even so, carbon measurements remain predominantly a manual operation with a low amount of control and automation around CIL and CIP reactors. Carbon inventory, i.e. knowing the carbon concentration in each reactor, is crucial for good carbon management. CarbonSense, a novel in-situ measurement system, was therefore developed for continuous monitoring of the carbon concentration in each reactor and paves the way for more advanced control in gold operations. The carbon management and optimisation system is based on Outotec® HSC Sim dynamic process simulations where each process component is modelled in detail. Generated models are validated with real data from a particular operation. The simulator will allow for the carbon control sequence to be realistically tested and the efficiency optimised by controlling the feed and discharge pumps in a hazard- and risk-free process environment. Furthermore, by combining CarbonSense and Outotec® gold courier (online soluble gold measurements) continuous feed-forward and feedback information can be obtained. The optimiser will then define the best running parameters based on the cost function of gold production versus intrinsic factors such as utility costs and adsorption time. Eventually, the application can be installed parallel with a real process island and it can be continuously calibrated with real-time process data. The dynamic model will then create future predictions for the entire process island. The example case presents a CIL circuit, which is simulated using Outotec® HSC Chemistry Sim and operated through Outotec® ACT (Advanced Control Tool) application. Keywords: Carbon-in-leach, CIL, CarbonSense, carbon management, automated control, simulation

Jan 1, 2020

By R. Craig McClung

Contrary to other sulfide minerals, where recovery is principally liberation controlled, the recovery of molybdenite is more complex. It is this complexity that initiated a geometallurgical investigation of molybdenites from Bingham Canyon. The aim of this investigation was to determine the effect mineralogy and/or mineralogical attributes have on recovery. All samples were analyzed using normal mineralogical techniques. The results reveal the presence of two distinctly different types of molybdenite. These have been identified as the two polytypes of molybdenite: i.e. hexagonal (2H); and rhombohedral (3R). The 2H-polytype occurs as textbook-shaped particles in quartz-molybdenite veins that are located in the current pit bottom. The 3R-polytype occurs as disseminated, “ball”-shaped particles with a dull or frosted appearance and are concentrated along the margins of the current pit. Concerning their metallurgical behavior, each type exhibits unique metallurgical properties that are consistent with those reported in the published literature. The 2H-polytype is easily ground and kinetically “faster” floating with surface attributes that are amenable to higher rates of recovery. This results in the production of a high quality concentrate under normal operating conditions. The 3R-polytype, by comparison, is difficult to grind and kinetically “slower” floating with surface attributes that are less amenable to recovery. Therefore, in deposits with higher concentrations of the 3R-polytype, modifications to the normal operating parameters may be necessary to improve recovery. This investigation highlights the necessity for understanding the mineralogical characteristics of any economic mineral(s), as these will have a direct impact on recovery.

By C B. Smith, G L. Boxer, S W. Moss, A L. Jaques, V Lorenz, M J. Rayner

The Ernest Henry Iron Oxide Copper Gold deposit is hosted in a large dilation between two moderately dipping shear zones found in the footwall and hanging wall of the deposit. These shears are controlled by a large diorite intrusion to the north-east and south-west of the deposit, formed ~1660 Ma. A shear zone dubbed the ‘Interlens’ uncovered through underground workings truncates the main orebody into two lenses, and is hypothesized to have formed in conjunction with the Hanging Wall Shear Zone and Footwall Shear Zone. All three shears dip moderately to the SSE (50–140) from open cut exposures through to the current mining horizon approximately 800 m below the surface. Routine geological work and a capital drilling campaign has identified a significant flexure in these sub parallel ore bounding shears with increasing depth. A shift in shear orientation in the Interlens over approximately 100 m vertically from ~50° to the SSE to a steep, easterly trend (~85° to the east) is observed in both drill core and exposures in the underground workings. It is hypothesized the diorite intrusive to the south-west of the deposit controls the shear zone geometries at depth. The geometry of the Interlens mirrors the surface expression of the Proterozoic package of the orebounding shears to the south-west of the deposit, suggesting the surface geometries of the shear zones are consistent with depth. Additional drilling to explore the validity of this hypothesis is planned for the near future to better understand the structural controls on the Ernest Henry mineralisation with increasing depth.

Mar 22, 2022

By O. Porterfield, M. O’Kane, M. Endersby

BHP Iron Ore initiated research programs in January 1995 to develop long-term plans for decommissioning waste rock material at its Mt. Whaleback operation. More than 2 Gt (2.2 billion st) of waste rock were deposited during the past 30 years. Ultimately, a total of 4 Gt (4.4 billion st) will be deposited in waste rock dumps constructed near the open pit. The Mt. Whaleback operation is located in a semiarid climate adjacent to Newman, Western Australia. The primary research program includes the development of technology for the long-term performance of the waste rock dumps with respect to vegetation, slope stability, surface runoff, erosion and water infiltration. This paper focuses on the design and implementation of a cover system to prevent water infiltration to the underlying waste rock. Data obtained from a laboratory program and from soil-atmosphere modeling was used to design horizontal field test plots. The construction of the horizontal surface field test plots is discussed together with the field instruments installed to monitor performance. The cover system is designed to maximize infiltration during wet periods for subsequent evapotranspiration while minimizing surface runoff. The result is a near-zero net infiltration to the underlying waste material. An important feature of the design is the use of run-of-mine waste material as the cover material. Monitoring is in progress and will continue for at least two annual wet/dry cycles. The optimum cover system should minimize the net infiltration of water to the underlying waste rock while maintaining physical and ecological integrity for long-term performance.

Jan 1, 2000

By James J. Komadina

INTRODUCTION Newmont Gold Company's Rain operations are located in Elko County, Nevada, approximately 9 miles southeast of the Town of Carlin.The property was submitted to Newmont Exploration Limited in 1979 and underwent development drilling over the course of the next four years, culminating in the completion of a project feasibility study in October 1986. Initial project scope included development of an open pit mine, an 815,000 DSTPY heap leach, a 572,000 DSTPY mill (Mill No. 3), and associated support facilities. Approval to proceed was given by Newmont Gold Company management in June 1987. Detailed engineering began in early July, followed immediately thereafter by procurement of major equipment components through various second hand sources. PROJECT DESIGN Keep It Simple In early August, Newmont Mining Corporation, parent company of Newmont Gold Company, became the takeover target of an "investor" group headed by T. Boone Pickens. Details of the ensuing events have been well documented by the press; suffice to say their impact on this project was material and required immediate flowsheet changes. Project design throughputs were increased to 1,000,000 DSTPY and 760,000 DSTPY for the heap leach and mill, respectively, in mid- September. These changes caused major project headaches as all general arrangement drawings had been approved and structural steel as well as concrete contracts were in place. Additionally, ground breaking was to commence in two weeks time! Rain project management assembled shortly after the announced changes, to devise an engineering and construction strategy capable of handling these new business conditions. The project had been justified using a gold price of $325 per ounce with a forecasted overall cash cost per ounce of $230. Hence, strict control of capital expenditures was necessary to maintain development economics. Mill start-up had also been moved forward one month, to August 1, 1988. To meet an already ambitious schedule, construction techniques needed to be simple and proven as most of the facilities were planned for erection during winter at a site with design criteria of -40F and 90 mile per hour winds. Perhaps the most critical factor requiring consideration was that of personnel. Newmont Gold's revised business plan called for corporate-wide production increases from 587,000 ounces per year in 1987, to 1,400,000 ounces by mid- 1989. Labor requirements were forecasted to grow from 900 employees to over 2,100. This fact, in combination with the rapid growth of Nevada's gold industry, led to the expectation that turnover of operating personnel would be extremely high. It was concluded that, to meet cost, time, and operational goals, the necessary strategy could be succinctly put - "Keep It Simple." Mining/Metallurgical Factors The Rain deposit consists of three interconnecting mineable shapes with host rocks ranging from 90%+ barite to a highly silicified jasperoid. Due to a limited number of mining faces in the first two years, in-pit blending

Jan 1, 1990

By Franz Xaver Spachtholz

K+S Potash Canada GP (KSPC) is part of the K+S Group, one of the world's leading suppliers of standard and speciality fertilizers and the world?s leading salt producer. Globally, the K+S Group employs more than 14,000 people. The K+S share ? the only commodities stock on the German DAX index ? is listed on all German stock exchanges. Legacy, K+S Group?s most recent project, is a greenfield solution potash mine and production plant in the south of the Canadian province of Saskatchewan. Therefore K+S will invest 4.1 billion CAD. With the expected commissioning in summer 2016 the company projects to reach the two-million-tonnesmark of production capacity at the new location at the end of 2017. The gradual extension of the annual capacity to 2.86 million tonnes of potash products will occur afterwards. The Legacy Project will be Saskatchewan?s first new potash mine in nearly 40 years. It is one of the world?s most economically attractive potash projects. The project will contribute to Saskatchewan?s growth through employment, tax revenues, utilities, and local partnerships. Located in the southern part of Saskatchewan?s potash belt, the deposit is too deep to be mined conventionally due to rock mechanics and high temperatures. Legacy will therefore be a solution mine. Proximity to the urban centers of Regina and Moose Jaw is imperative, with their workforces and economy, as well as access to highways, railway carriers and, most importantly in the prairies, water. With this unique project setting and mining technique, we are convinced that Legacy will be one of the most efficient, economic, sustainable and safe potash facilities in the world.

Aug 1, 2013

By T Soares, P Esteves, C Senna, V Souto, E Dias

Steinert provides a wide portfolio of Sensor Based Sorting (SBS) technologies, including the possibility to combine different sensor data in the development of the separation applications. This multi sensor approach provides a larger applicability and extensive flexibility for the technology. This effect is emphasized for mining applications, once every ore body presents its own features that can also comprise a large material variability. In this sense, every sorting application is customized and comprises a personalized solution. This means each project development includes a test work stage that approaches from the project discussion, test definition, up to test outcomes and processing development. In relation to very complex and large projects, a sorting pilot scale plant has become a crescent tendency. By having a pilot plant stage can represent a chance to test larger amounts of material from different mining areas, different mining projects, such as to consider different processing targets and application approaches. Based on that, a better understanding about the technology application can guide a more assertive development of large and complex ore sorting projects. The aim of this paper is to provide information about the applicability of the Steinert multi sensor technology at different pilot plants in South America. It consists in a compilation of laboratory test results, plant design and operational results. For that, a chromite, an IOCG deposit and a sulphide gold ore projects are presented. Additionally, the paper discusses the application of different sensor technologies combinations such as various processing targets, thus providing a wider understanding about sorting applications and flexibility.

Nov 10, 2020

By Victor E. Kral

The Valery fluorspar deposit , also known as the Hamilton deposit , is northeast of Lovelock and 4 miles by poor dirt road east of U. S. Highway 40 . It is in the Humboldt Mining District , on the west side of the Humboldt Range , at an altitude of 6,000 to 6,500 feet . The property was examined by the Bureau of Mines on February 83/ and April 8 , 1944.4/ The last examination was made with an engineer of the Geological Survey.5/ Exploring by means of trenches , cuts , shaft sinking , coyote holes off the shaft , and a small amount of prospecting with short drill holes , was begun in January 1945 and was completed June 30 , 1945. An engineer6/ of the Geological Survey visited the property in April and again in June 1945 to complete a topographic map of the area and to note the results of exploration by the Bureau of Mines . Only minor surface exploring had been done on fluorspar occurrences previous to the Bureau's work . No mining equipment or living facilities are on the property .

Feb 1, 1947

By Y. R. Murthy, S. Angadi, A. K. Bhatnagar, S. K. Tripathy, L. O. Filippov

Dolomite is an essential raw material for the refractory industry, a flux in the iron and steel industry and also for the extraction of magnesium metal. Generally, particle size reduction, screening and classification are used for the preparation of the high-grade sized material for different applications, whereas low-grade fine fractions are not utilised. These fines or low-grade overburdens are dumped at the mine site for future utilisation, which creates environmental issues along with inadequate space management. In the present investigation, a detailed study was carried out to decrease the silica content of the low-grade dolomite fines from Gomardih , India, containing 28.6% CaO and 20.1% MgO along with 8.3% silica. Different process flow sheet options were evaluated with a combination of dry classifier, wet classifier, gravity concentrators as well as flotation. Different process variables were assessed along with mineralogical characterisation to optimise the process for efficient rejection of siliceous gangue minerals. Results indicated that dolomite, calcite and quartz are the major mineral phases present in the ore along with other minor minerals. It was concluded that two-stage flotation was an effective process for the reduction of silica up to below 1% after grinding to a particle size below 212 μm. A process flow sheet with a combination of gravitation air classifier and flotation can produce a concentrate with silica content below 4.5%. Keywords: Dolomite, flux, dry classification, flotation, characterisation, beneficiation

Jan 1, 2020

By M Scoble

This paper addresses the importance of collaborative approaches to resolving future mining challenges. It attempts to provide some insight into understanding the theory, measurement, mapping and management of collaboration. This is related to the design and planning for successful research and educational initiatives. Reference is made to Canadian and global case studies and personal experiences.

Nov 22, 2011

By Joseph A. Dos Santos

The largest TBM (Tunnel Boring Machine) tunnels are typically along modest slopes, but not always. Occasionally high slope angles are required beyond the capabilities of conventional open trough trailing conveyors. A 2019 project required a large TBM to ascend to an incline angle of 25°. A Sandwich Belt high angle conveyor could easily solve the high angle conveying problem but such a system must include all of the features of the conventional trailing conveyor, particularly the ability to extend with the TBM advance. The writer responded to the challenge and developed a TBM trailing Sandwich Belt high angle conveyor with all of the needed features. The invention (U.S.A. patents awarded October, 2021 and November, 2022) however goes beyond the 2019 project requirements and extends to any high angle incline. This writing first presents the broad Sandwich Belt high angle conveyor development, then its use in various construction and tunneling projects prior to this TBM Sandwich Belt trailing conveyor invention. Finally we present the new TBM Trailing Sandwich Belt high angle conveyor with all of its features and implications.

Jun 13, 2023

By Stephenson D. B, Burgess J, Burgess F. L, Marshall S. H

A new high intensity flotation process 'FASTFLOT' is explained and its theoretical advantages compared with other flotation systems are discussed. The results of initial FASTFLOT testing on the zinc roughing circuit at Pasminco Mining, Broken Hill South concentrator are presented and compared to recent plant data. The comparison suggests that on roughing duties, the FASTFLOT process yields superior concentrate grade while requiring less than one third the residence time of a conventional mechanical cell plant. Strategies for FASTFLOT deployment are also presented.

Jan 1, 1994

THE Synthetic Liquid Fuels Act. (30 U.S.C., 321-325, and amendments) became law April 5, 1944, and a period of intensive research and development in this field was begun by the Bureau of Mines. As part of this program, bulletins were published on pressure hydrogenation.3 the Fischer-Tropsch synthesis,4 anal oil shale.5 The Bureau also has published a short bibliography on coal gasification,6 mostly of a theoretical nature. Because coal gasification is prerequisite to either the Fischer-Tropsch or coal-hydrogenation processes, publishing this sizable collection of technical information in this form will be valuable. The material will be presented in three parts, as follows: I. United States Patents. II. United Kingdom Patents. III. Other Foreign Patents. The domestic patents for this bulletin were collected between 1953 and 1955.

Jan 1, 1960

By William O. Vanderburg

This paper 3/gives the results of a reconnaissance of mining districts in Clark County, Nev., made from November 18 to December 22, 1936, and from February 9 to March 8, 1937-in all, 63 days. While the field work Was being done, virtually all of the mining districts in the county were visited and many data on active and inactive properties were obtained. The report covers the locations of the various mining districts, the nature of the deposits, information on past operations, current activity, and general data likely to be useful to operators, investors, and others interested in mining. The geology of the deposits is discussed only briefly. The principal metal-mining districts in the county are Goodsprings, Eldorado, and Searchlight. The zinc-lead ores of Goodsprings have been the most important economically, followed by the gold-silver ores of Eldorado and Searchlight. In the industrial-mineral field, gypsum, limestone, silica sand, and borates are the principal products. Metal mining in the county is characterized by numerous small operations and the ores are either milled locally or shipped to distant smelters.

Jan 1, 1937