Search Documents

By C. A. Mehring

[This paper, which describes the milling practice at the San Guillermo concentrator of the Compania Industrial "M Potosi", S.A., located at Chihuahua, Chihuahua, Mexico, is one of a series of similar papers being prepared by the United States Bureau of Mines. The concentrator treats lead-zinc-silver ore at the rata of 2,300-2,400 tons of dry material daily and produces lead concentrate and zinc concentrate by selective flotation methods. The lead concentrate is smelted at the Chihuahua plant of the American Smelting & Refining Co., and the zinc concentrate is shipped to various European smelters.]

Jan 1, 1933

By J. H. Johnson

The report references reports and publications from 1975 to the present related to diesel underground mine air quality research undertaken by Michigan Technological University. Research results obtained on this contract are summarized in 5 different sections as follows: Section 1 - Development of a Systematic Approach to Monitoring, Data Analysis, and Interpretation for Diesel Mine Air Quality Control, Section 2 - Experimental Evaluation of LHD On-Board Air Quality Control Systems, Section 3 - Development of a Portable Self-Contained LHD Tailpipe Emissions Measurement Apparatus for NO , N0, CO, CO , and Particulate Matter, Section 4 Quantitative Analysis of Diesel and Coal particulate Matter by Laser Raman Spectro¬scopy and Section 5 - Development and Application to Detector Tubes of a Laboratory Method to Assess Accuracy of Occupational Diesel Pollutant Concentration Measurements.

Jan 1, 1985

By W. E. Lamont

The Federal Bureau of Mines, in cooperation with phosphate companies in the Florida land-pebble area, made a comprehensive study of the waste clays, or "phosphate slimes," produced in the mining of phosphate rock in Florida. These slimes represent a significant ecological problem and a major deterrent to effective land recovery in the phosphate-mining areas. Physical, chemical, and mineralogical studies were made of slime samples submitted by 15 of the 16 plants in Florida in an effort to identify factors that prevent successful consolidation of the slimes and subsequent recovery of the mined lands. Results of these studies indicated that the clay mineral attapulgite, a hydrated magnesium silicate, was primarily responsible for the very poor settling characteristics of the slimes, and that the quantity of attapulgite in the slimes effectively controlled the settling rate, pulp density of terminal solids, viscosity, percent solids of filter cake, and flocculant requirements.

Jan 1, 1975

By Johann Steynberg

The design and construction of a Concentrator based on initial pilot plant work is rarely perfect. Palabora's plant was no exception although the basic objective to produce copper in a safely conservative manner was certainly achieved in a profitable manner. identification of the metallurgical and mechanical deficiencies of the plant through operating experience and a better concept of the minerology of the orebody enabled the development of a more efficient process both in terms of the metallurgical performance and cost effectiveness. To maintain and improve this level of efficiency, continuous inspection and revision of the plant metallurgy and engineering standards is required. In this presentation a few of the investigations and changes are described: 1.0 Alternative methods to restrict and eliminate the detrimental effect of critical size material on the performance of an autogenous mill. 2.0 An analysis of the environmental condi¬tions in Palabora's grinding circuit and the introduction of high chrome balls as grinding media. 3.0 The role of magnetite in the beneficiation process at Palabora. 1.0 Alternative methods to restrict and eliminate the detrimental effect of critical size material on the performance of an autogenous mill.

Jan 1, 1985

By William F. Jahn

Because of the' situation in Europe during the summer of 1939, with the possibility of war and consequent curtailment or loss of supplies of tin to the United States, the Bureau of Mines undertook an investigation of domestic tin resources. This was permitted by the Strategic Minerals Act of 1939, which authorized investigation of possible domestic resources of strategic minerals necessary in a national emergency. The minerals selected were in short supply, and the United States depended almost entirely on imports to meet normal requirements. The Black Hills of South Dakota were selected for investigation as one possible source of tin because of the occurrence of the mineral there has been known since 1876, although production had never been important. The Tinton area, in the northern part of the Hills, had received the most attention and contained some minor indicated and inferred tin deposits.

Jan 1, 1949

By H. Dolezal

A laboratory study of acid-ferrous sulfate treatment of low-grade manganese ores from the Cuyuna range, Minnesota resulted in 93-percent extraction of manganese as manganese sulfate with consumption of 3.8 pounds of H2S04 per pound of extracted manganese. Two types of ore were treated in consecutive stages. The first are contained carbonate minerals of manganese and iron, both soluble in H2S04 solution. The second ore contained manganese oxide minerals, insoluble in straight acid solution but soluble in the ferrous sulfate solution obtained from treating the first ore. Leaching data were obtained by countercurrent percolation of coarse (minus-1/2-inch) ore particles at room temperature and by agitating minus-65-mesh ore particles in heated solution. Extraction of manganese and acid consumption were the same, but the percolation leach required 6 days compared with 1 hour for hot agitation. Variations in the size of ore particles treated, leaching time, acid concentration, solution temperatures, and method of applying ferrous sulfate solution to the oxide ore were studied. The effects of several reagents for removing iron from solution and improving filtration were also studied.

Jan 1, 1959

By D. H. De Jager

Fluorapatite is an important constituent of the greater part of the basic and ultra-basic rock members of the Complex. The evidence for and role of primary magmatic processes in the development of concentric zones of dunite, pyroxenite, syenite and carbonatite and its consequent bearing on the distribution of apatite are discussed. The presence of at least two generations of each of the latter three rock types indicates the cyclical nature of magmatic activity. Pegmatitic-metasomatic phases corresponding to the major magmatic cycles resulted in emplacement of pegmatoidal assemblages. The abundance of apatite in the pegmatoid can be traced to the composition of its parent magma and its cooling history. Approximately 2.5 million tonnes of phosphate concentrate are produced annually from ores containing from 10 percent to 25 percent apatite.

Jan 1, 1978

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Amilton Barbosa Botelho Junior

A new step in the Bayer process has been used to recover NaOH and to reduce its content in red mud. After digestion, the residue is separated from the Bayer liquor and goes through press filters, which enables the recovery of NaOH and decreases the moisture content. It is well known that red mud is one of the most important sources of scandium. For this reason, the goal of this work was to characterize a Brazilian red mud (BRM) for scandium recovery. The sample was collected after the press filter system process. Analysis of energy-dispersive X-ray fluorescence (EDXRF), scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDS), and X-ray diffraction (XRD) was performed. Microwave digestion using an acid mixture was carried out to determine the concentration of the main elements. Fe2O3 represented 40% of the BRM, and the Sc concentration was 43 mg/kg. The SiO2 content was 24%, which is the highest value found in the literature, whereas the sodium concentration was the lowest. A literature review was carried out to compare results with BRM, as well as the current studies for recovery of scandium by the leaching/ion-exchange process. Scandium recovery using a leaching/ion exchange process may be possible with efficiency higher than 90%. The greatest challenge is the occurrence of silica gel formation during leaching.

Oct 19, 2020

By S. G. Cupschalk, F. A. Dahlman, J. J. Wert

Studies have been undertaken to determine the indicidual effects of particle size, degree of long-range ovder, antiphase domain size, and root mean square stran on the microhardness and yield strength of ordered alloys. Dnta have been analyzed for Cu3Pt initzally ordered to a value of 0.82 and after deformations of 1 and 6 pct. It was observed that deformation fleatly reduced the degree of long-range order. Furtherrnore, wztkin this range of relatively small deforntntlons, the average particle size changed very little while the antiphase domain size was greatly reduced. Smultaneosly, the mcrohardness changed by a factor of two durzng the deforrtation process. PREVIOUS studies have reported some of the effects of cold work on the broadening of X-ray diffraction peaks. These investigations were performed on powder and wire samples representing both ordered and disordered states; i.e., the specimens were initially studied in a severly cold-worked condition. By comparing the difference in line shape between the annealed and cold-worked peaks, fundamental information was obtained concerning particle size, strain distribution in different crystallographic directions, degree of long-range order, and change in antiphase domain size. Considerable theoretical work has been done concerning the analysis of diffraction data obtained from cold-worked metals. Stokes' expressed the change in diffraction profiles in terms of Fourier coefficients. Much of the work in this area has been summarized by warren2 in an extensive review article concerning the analysis of plastic deformation by X-ray diffraction. Cohen and Bever3 applied these techniques in studying the effects of cold work on alloy systems exhibiting long-range order. They utilized the Fourier coefficients of fundamental peaks in conjunction with those of the superlattice peaks to determine the change in antiphase domain size. Little work of this nature has been reported for ordered systems that have undergone small degrees of plastic deformation. The purpose of this investiga-tion was to determine the effects of small deformations in such a material with respect to particle size, strain distribution in various crystallographic directions, antiphase domain size, degree of long-range order, and hardness. EXPERIMENTAL PROCEDURE CusPt was used for the initial investigation since the order-disorder transformation takes place with- out a change in crystal structure. The transformation is readily detectable via X-ray diffraction techniques due to the large difference in the scattering factors of copper and platinum. Additionally, the alloy is relatively low melting (approximately 1300°C) and is easily deformable in both the ordered and disordered states. 1) Specimen Preparation and Cold Working. A 100-g, 12-in. diam., cylindrical specimen of Cu3Pt was prepared by melting and casting 99.99 pct pure Cu and Pt i.n vacuo. Prior to any mechanical working, the material was homogenized in a vacuum for 60 hr at 100O0C, and surface defects were removed by machining to a depth of approximately 116 of an in. The material was then cold-rolled, with an intermediate anneal, into a strip approximately 12 in. wide by 14 in. thick. Straightening and flattening removed another 0.025 in. from the thickness. After a recrystallization treatment at 750°C for 30 min, the specimen was slow-cooled from 55OoC, at the rate of 6°C per hr, down to 150°C to induce superlattice formation. This treatment yielded an ASTM grain size of 7 and a degree of long-range order equal to 0.83 0.06. After obtaining X-ray and Knoop hardness data, the sample was cold-rolled approximately 0.75 pct in one pass through a hand-operated jewelers' mill. X-ray and hardness data were again obtained and the specimen was reduced an additional 5.41 pct in a single pass through the mill. 2) X-Ray Measurements. The specimen was examined in the ordered condition and after the two degrees of cold working previously mentioned using a General Electric XRD-5 unit equipped with a spectrometer and scintillation counter. Using Mo-Ka radiation with a zirconium filter, six orders of the 100 reflection were obtained. It was anticipated that point counting would be necessary for an accurate determination of the low-intensity peaks and tails: however, it was demonstrated that, by using a scanning speed of 0.2 deg per min and the appropriate time constant, the recorded data were sufficiently accurate. Thus, for ease of experimental procedure, all peaks were recorded on chart paper. Specimen position in the holder was considered to be insignificant after making a series of measurements of the same peak area in different positions with respect to the beam. Since peak overlapping did occur at high values of 20, it was necessary to separate the peaks graphically prior to analyzing the data in order to minimize this source of error. The peak tails were also carefully drawn to obtain the best possible data. Fourier coefficients of the line profiles were calculated on an IBM 7072 computer, and graphical meth-ods2j3 were employed in analyzing the results. For this type of calculation, in which the line profile is represented by intensities taken at set intervals, the intervals selected must be sufficiently small to give an accurate representation of the line profile. It was decided that for 20 = 0.02 deg the line profiles were

Jan 1, 1967

By James J. Bean

F. M. Lewis—I believe that density recorders are a prerequisite to all well operated ore concentrators. Well designed density instruments are very accurate and give an excellent record of the steadiness of the operation. Controlling the density of a pulp with an instrument, as described by Mr. Bean, is new and the experiences in developing this controller at the American Cyanimid Co.'s Mineral Dressing Laboratory are very interesting and should be extremely helpful to others who are planning on designing or installing controlling density instruments. Instruments for recording the density of the classifier overflow or flotation feed are rather common in ore concentrators, but there are a number of profitable uses for these instruments that are not too well known. Density recorders with bubble tubes submerged to different depth in a classifier pool give an excellent record of the classifier operation. The loading and unloading of the machine, that is so easily masked in the density of the overflow, can be easily recorded if the instrument is installed at some depth in the classifier pool. On some occasions, two instruments with bubble tubes at different depths give a more candid picture of the irregularities in the classifier operation. When cleaner machines are operated in closed circuit with roughers, a record of the density of the cleaner tails will indicate the circulating load in the circuit and is very helpful in coordinating different operators, because quite often the circulating load will be increasing for some time before the analyses of the products will change. Density recorders are used to record the variations in the dilution of the underflow from thickening tanks and in at least one plant the instrument controls the underflow.

Jan 1, 1951

By James J. Bean

F. M. Lewis—I believe that density recorders are a prerequisite to all well operated ore concentrators. Well designed density instruments are very accurate and give an excellent record of the steadiness of the operation. Controlling the density of a pulp with an instrument, as described by Mr. Bean, is new and the experiences in developing this controller at the American Cyanimid Co.'s Mineral Dressing Laboratory are very interesting and should be extremely helpful to others who are planning on designing or installing controlling density instruments. Instruments for recording the density of the classifier overflow or flotation feed are rather common in ore concentrators, but there are a number of profitable uses for these instruments that are not too well known. Density recorders with bubble tubes submerged to different depth in a classifier pool give an excellent record of the classifier operation. The loading and unloading of the machine, that is so easily masked in the density of the overflow, can be easily recorded if the instrument is installed at some depth in the classifier pool. On some occasions, two instruments with bubble tubes at different depths give a more candid picture of the irregularities in the classifier operation. When cleaner machines are operated in closed circuit with roughers, a record of the density of the cleaner tails will indicate the circulating load in the circuit and is very helpful in coordinating different operators, because quite often the circulating load will be increasing for some time before the analyses of the products will change. Density recorders are used to record the variations in the dilution of the underflow from thickening tanks and in at least one plant the instrument controls the underflow.

Jan 1, 1951

The implementation of robust, reliable and accurate sampling systems is the key to the successful management of any mineral processing plant. The representative sampling of a mineral processing plant is the only way to determine what is coming into the plant, what is going out as fi nal product and what is going to tails. In plants with high gravity gold components, where high recovery effort gravity circuits are installed, the use of a gravity recoverable gold (GRG) sampling system can assist in the online monitoring of the performance of the circuit. The typical installation location would be in CIP or fl otation feed (ie cyclone overfl ow), downstream of the gravity circuit. A GRG sampling system generally consists of the following equipment: true proportional, continuous drive, linear cross cut sampler, secondary vezin sampler operated on a timer, a batch centrifugal concentrator, and sample dewatering module. The operating philosophy of the GRG sampling system is that the primary sampler operates on a continuous basis, generating a constant stream of truly representative sample. Consep's H&S drive system is unique in its ability to be able to operate in a continuous mode, therefore enabling a continuous stream of representative sample to be generated. The primary sample stream reports to the secondary sampler. The secondary sampler operates on an intermittent basis (nominally ten minute interval), resulting in a relatively small sample volume per shift. Normally the sample volume would be ten to 15 L per shift. The secondary sample rejects stream reports back to the batch centrifugal concentrator. The sample generated from the secondary sampler can be dewatered using a Consep H&S dewatering module. This device produces a final sample that consists of separate filter cake and filtrate. These are suitable for taking directly to the laboratory. The continuous stream of truly representative secondary sampler rejects is passed through an appropriately sized Knelson Concentrator, typically a KCMD7, KCCD10 or KCCD12 sized unit. This unit recovers any available GRG from the stream. The Knelson Concentrator is also purged of its gravity concentrate at the end of the shift. This sample, which is nominally around 1 - 2.5 kg of concentrate, is also taken to the laboratory. At the end of the shift the client will have a measure of the gravity recoverable gold content of the target slurry stream, as well as a true representative sample of the complete stream. Through the addition of a Knelson Concentrator to an otherwise typical sample station, it is possible to generate a true measure of the performance of your gravity circuit. This will take the guess work out of the daily variation in gravity circuit gold recovery, as the site knows whether the changes are due to gravity circuit equipment performance, or due to the natural variation of ore GRG contents. Maintenance planning can also be designed around the system, as the site will have a composite sample to measure the performance of the circuit, therefore indicating where performance has dropped and maintenance is needed. This is an ABSTRACT ONLY. No paper was prepared for this presentation.

Aug 1, 2010

By A. S. Winters

INTRODUCTION Homestake Mining Co. owns and operates the Bull¬dog Mountain mine near Creede, CO. Lead-silver con¬centrates are produced from ores extracted from narrow veins which dip from 1.04 to 1.39 rad (60 to 80°). An¬nual mill throughput is approximately 90 700 t (100,000 st). Ore shoots average 2 m (7 ft) in width and the ore is often weak, muddy, and poorly consolidated. Walls can be either strong or highly fractured along the strike of the veins. Cut-and-fill methods were initially selected to mine the deposit and considerable overhand mining occurred during the initial stages of the mine. Because of un¬stable ground conditions, mine management recognized that other methods would have to be employed. Undercut-and-fill mining was adapted to extract the loose ore from narrow veins and is presently the primary method used. Approximately 80% of the annual pro¬duction is extracted by this system. Loading ramps are positioned along the strike of the vein on 90-m (300-ft) intervals to allow for 45-m (150-ft) long cuts in each direction from the extraction raise. This interval was selected for efficient slusher operation and stope cycling. Loading ramps rather than chutes were selected for ore movement into 4.5-t (5-st) Granby-type cars because of extremely sticky ore conditions. Mined-out areas are filled with deslimed mill sands. Sand is pumped from the mill into two mine storage dams where the water is decanted. Each dam has a 544-t (600-st) capacity. Sand is pumped into the mine at a 30 to 40% slurry through 2195 m (7200 ft) of 51-mm (2-in.) thick wall pipe. When called for, sand is reslurried within the dams to a density of 55 to 65% and pumped to the particular mine opening requiring fill. Dry cement is added to the slurry prior to pumping. The capacity of the mine fill system is 20 t/h (22 stph). DEVELOPMENT Vertical development below the main adit level oc¬curs on 61-m (200-ft) intervals from an internal winze. Main haulage drifts or laterals are 2.7 x 2.7 m (9 x 9 ft) in section and driven parallel to the vein structures. Ground conditions generally dictate that better progress can be realized in the footwall than in the hanging wall. A distance of approximately 21 m (70 ft) is maintained between vein and drift openings to accommodate a smooth 18-m (60-ft) radius curve for crosscuts which are driven on 91-m (300-ft) intervals. Approximately 18 m (60 ft) of tail room is driven past the vein inter¬section to accommodate train loading. Ore and waste are hauled using diesel or electric driven locomotives operating over 18-kg (40-Ib) rail [762-mm (30-in.) gage]. Loading ramps are established above each crosscut¬ vein intersection. Scram drifts are then driven in the vein to determine the width and grade of the ore. If a prior decision to mine the block had been reached, then the scram is driven only far enough [about 12 m (40 ft)] to establish a drawpoint and scraper tail room. In most cases, the drawpoint is a 2.1 x 2.1-m (7 x 7-ft) cutout driven about 2.4 m (8 ft) into the footwall. On the level above, a raise bore station is established in the footwall to one side of the crosscut-vein inter¬section. The station is of sufficient size to accommo¬date a Robbins 41R raise boring machine. Support for the station is accomplished with 1.2 and 1.8-m (4 and 6-ft) roof bolts and wire screening. Once completed, a 152-mm (6-in.) concrete slab is poured and the raise drill set in position to center the 1.5-m (5-ft) diam hole approximately 1.8 m (6 ft) from the vein footwall. A 229-mm (9-in.) pilot hole is then drilled to the scram cutout below and reamed back to full diameter (see Fig. 1). STOPING Initial mining in a typical undercut-and-fill stope be¬gins from the top of the borehole. The initial cut can be either immediately beneath the track level or the old scram drift depending upon the particular situation. Cuts vary but are generally 2.4 to 3 m (8 to 10 ft) high. Support is accomplished by square-set timber, overhead caps, or roof bolts and screening depending upon ground conditions. Once the initial cut is removed, underhand timber and screen is installed and cemented sand fill placed. The stope is then ready for undercut mining. Prepara¬tion work begins with sinking 4.5 to 6 m (15 to 20 ft) on the borehole plus cutting a slot to the vein. As sinking progresses, hanging sets are installed to provide man¬way and service facilities. Hanging sets 1.7 m (5 ft 8 in.) long and 1.6 x 2.2 m (5 ft 4 in. x 7 ft 4 in.) in section are installed with steel hangers similar to shaft sets. Framed 203 x 203-mm (8 x 8-in.) timbers are made up in advance and shipped to the stope during sinking operations. When manway and service facilities are completed to the floor of cut to be mined, generally 3.65 to 4.3 m (12 to 14 ft) below the previous sand fill, the ore is removed to the hanging wall plus a round each way along the vein. Levelers or long stringers are then installed over the raise opening to support the work deck, slusher, and grizzly opening. All waste and ore from the sinking process is fed by gravity to the raise (see Fig. 2). Once the stope is equipped, mining pro¬gresses outward in each direction from the grizzly open¬ing. Stope equipment consists of 907 kg (2000 lb) pull air tuggers, timber skips, 11-kW (15-hp) ventilation fans, 15 to 22-kW (20 to 30-hp) electric slushers, 762 to 1270-mm (30 to 50-in.) scrapers, 67-mm (25/a-in. ) jackleg drills, as well as other drilling and blasting supplies. In narrow stopes [generally less than 2 m (7 ft) wide], no support is required for the underhand caps of the previous fill. Where wide sections in the vein occur, segment braces are installed beneath the caps to insure that the sand support cannot slip away from the hanging wall. Sections as great as 6 m (20 ft) wide and 4.5 m

Jan 1, 1982

By Warder A. Shaver

INTRODUCTION Mine No. 95 of the Consolidation Coal Co., a divi¬sion of Continental Oil Co., is located in Shinnston, WV. Mine No. 95 was opened in January 1967 and has been operating continuously since that time. The mine has 544 hourly and salaried employees. In 1974 this mine was the largest coal producer in West Virginia. Opera¬tions include two longwall sections and eight Marietta Borer continuous miners. Originally there were also two Jeffrey Heliminer continuous miners, but use of these was discontinued in June 1978. Production averages 12 727 t/d (14,000 stpd). Two portals now service the mine with a third portal proposed for 1978. GEOLOGY Mining takes place in the Pittsburgh coal seam which dips 0.04 rad (21h°) northwest. The working seam is steam coal with an average height of 2.2 m (86 in.). Immediately above the seam, the overburden is com¬posed of 6.1 m (20 ft) of shales followed by 6.1 m (20 ft) of weak sandstone and 51.8 (170 ft) of shaley limestone. The shale weathers when exposed to mois¬ture. Surface water has been a problem due to a fire¬clay floor which turns to paste when mixed with water. GENERAL DESCRIPTION The present mining plan for Consol's No. 95 mine has a proposed life of 35 to 40 years. One set of main headings has been driven in the north direction and one set in a western direction. These are the areas in which the majority of the virgin coal lies. The panels are driven off of the mains at 2134 to 3048-m (7,000 to 10,000-ft) intervals. The continuous mining sections are set up 133 x 610 m (600 x 2000 ft). Longwall sections are 259 x 1220 m (850 x 7000 ft). All of these mining sections are retreating uphill. Development is with continuous miners. A Marietta Borer miner is used for the main development work. These miners cut 4.1 m (13 ft 6 in.) wide and 2.1 m (7 ft) high, leaving an arch cut. Along with the arch, a 152.4-mm (6-in.) thick layer of roof coal is left in place to protect the roof from weathering. The combi¬nation of the self-supporting arch and the roof coal al¬lows the entries to be driven 30.5 m (100 ft) without bolting. Full bolting, however, is carried outby the last open crosscut. This bolting is done on 1.5 x 1.5-m (5 x 5-ft) centers using 1.5-m (5-ft) long roof bolts with tandem anchors and 152.4-mm (6-in.) steel washer plates. When needed, crib blocks with a 50.4-mm (2-in.) drill hole are used as supplemental supports. Three-hole steel channel with the ends curved down¬ward to conform to the borer arch may also be used. In the mining sections, a 14 BU loader is used be¬hind the Marietta miner to load two Torkar shuttle cars. These haul to Long-Airdox feeder breakers which load onto a 1.07-m (42-in.) wide conveyor belt. With the exception of the shuttle cars, which use 275-V d-c power, the face equipment operates on 550-V a-c power. The main power line is 7200 V ac. The same loading and hauling equipment is used with the Marietta Borer miner for driving both panel and development entries. In the retreat sections, the same equipment with the exception of the miner is utilized. Because of the advantage of a variable cutting hight, Jeffrey Heliminer ripper-type continuous miners were employed in these retreat sections. For longwall mining the first unit uses an Eickoff EDW 300-L double-drum ranging shearer. Drum di¬ameter is 1.69 m (66 in.) with a drum rotation speed of 45 rpm. The drum is equipped with 48 Carmet 34-L-1 bits. The 300-kW (400-hp) motor operates on 1000 V. Tramming of the shearer head is done through a hydraulically driven 26-mm wide chain. Maximum cutting speed is 7.93 m/min (26 fpm), and maximum tram speed is 12.8 m/min (42 fpm) with an average cutting speed of 3.66 m/min (12 fpm). Web cutting depth is 762 mm (30 in.) and the cutting height is 2.13 m (7 ft). The conveyor width is 686 mm (27 in.). It uses a single chain, 26 mm thick, with flights on 0.91-m (3-ft) spacing. The face conveyor speed is 64.3 m/min (211 fpm) when driven by two 112-kW (150-hp) 1000-V Louis Allis motors through torque convertors. The roof support used is Gullick Dobson chocks [6-legged 77.3 t (85 st) per leg, 463.6 t (510 st) total capacity] with double-acting leg jacks. The hydraulic pressure for the legs is 13.8 MPa (2000 psi), and the hydraulic pressure for rams is 6.8 MPa (1000 psi). The yield valves are set at 57.8 MPa (8500 psi). Each chock weighs 4.09 t (4.5 st). The stage loader is an Eickoff drive, with a 68-kW (90-hp), (00-V Reliance motor. A 26-mm thick single strand chain with flights on 0.6-m (2-ft) centers runs at 75.89 m/min (249 fpm). The stage loader is self-advancing and is connected to the belt tail piece with a special fifth wheel attachment so that the stage loader can advance and guide the tail piece. The hydraulic pressure for the roof support is supplied by two 45-kW (60-hp) Reliance motors op¬erating on 699 V, with 1.26 L/s (20 gpm) constant volume Gullick hydraulic pumps. Each pump services alternate chocks, with the two pressure lines connected at the tailgate by 25.4-mm (1-in.) hydraulic hoses, rated at 27.21 MPa (4000 psi). The 6.8 MPa (1000 psi) pressure rams advance is supplied by a 45-kW (60-hp), 600-V Reliance motor and a 1.26-L/s (20-gpm) con¬stant volume Gullick pump. Return lines are 35.5-mm (1.4-in.) diam hydraulic hoses with rated capacity of 27.21 MPa (4000 psi). The fluid used in the hydraulic system consists of 95% water and 5% Hy-chock fire resistant water soluble oil. Water is stored and mixed in a 6096-L (2000-gal) track-mounted tank and goes to a 655-L (180-gal) reservoir at the pump. The belt conveyor structure is 1.07 m (42 in.) wide with 0.47 rad (27°) idlers, bottom stands located on 3.05-m (10-ft) centers, top stands on 1.5-m (5-ft) centers, and is supported on a 19-mm (3/4-in.) diam

Jan 1, 1982

By R. T. Southin

Cast ingots of 99.99 pct purity A1 and aluminum/copper alloys containing up to 2 pct Cu have been found to contain four zones rather than the three previously accepted, i.e., chill, colummar, and equiaxed zones. The fourth zone consists of a coarse dendritic layer across the top surface of the ingot which is open to the atmosphere. It is also found that the grains in the equiaxed region have a "cornet" shape, with a head which is coarsely dendritic and a tail which grew with the same structure as the columnar grains. Experiments using mechanical barriers, and others involving the elimination of the surface dendrile layer, have indicated that nucleation of the equiaxed zone is caused by the showering of dendritic particles from this surface dendrite layer. These particles are the dendritic heads found in the comet grains. A mechanism of nucleation and growth of these comet grains is put forward. Experiments with a number of other metals and alloys suggests that these conclusions may apply generally to ingots cast without the addition of nucleating agents, and solidified under normal conditions. THE macrostructure of cast ingots may contain the following three zones: i) a peripheral zone of fine equiaxed grains, commonly called the chill zone; ii) a zone of columnar grains extending inwards from the chill zone; iii) a central zone of equiaxed grains; these are normally larger than the chill grains. All three zones are not necessarily present in any particular ingot since their existence and magnitude depend upon the casting conditions and composition of the cast material. The mode of formation of zones i and ii is fairly well understood. However, the cause of the central equiaxed zone remains a matter of conjecture. Previous theories put forward to explain the mechanism of nucleation in the equiaxed zone have been examined by Chalmers1 and Winegard.2 At the time when the present work was carried out the most re -cent hypothesis was that due to Chalmers,1 who recognized more fully than previous workers that conditions in this zone during solidification were not conducive to nucleation. In his hypothesis, he suggested that nuclei were formed near the mould wall during the very early stages of solidification, and that they can drift into the central zone by convective motion. This was supported by evidence from experiments using mechanical barriers to stop the drift of nuclei. A similar hypothesis had previously been put forward by Genders.3 More recently, Jackson et al. 4 have observed that dendrite arms in organic compounds can melt off during solidification. They have postulated that this occurs in metals and alloys, and that the dendrite arms which have been freed from the main dendrite act as nuclei for the equiaxed zone. In the present work, critical metallographic examination has shown that there is a fourth zone in the macrostructure of cast ingots which is a dendritic layer over the top surface of the ingot. It is also shown that there is a relationship between this zone and nucleation of the equiaxed zone. EXPERIMENTAL DETAILS The alloys examined were prepared from super -purity aluminum of 99.99 pct min purity (spectro-graphically detected impurities of Cu, Fe, Si, and Mg) and copper of 99.98 pct min purity (spectrographically detected impurities of Si, Zn, As, Fe, Pb, Bi, Ni, Sn, Mn, Ag, Cr, and Al). Three compositions of ingots were examined, containing 0.0, 0.1, and 2 pct Cu, respectively. The alloys were melted in an alumina-lined salamander crucible using a medium-frequency electric induction furnace; when the appropriate casting temperature was reached, the alloys were cast without degassing or fluxing treatment. The mould used was made of electrode graphite and had the following dimensions: external diameter 6 in., height 9 in., with a mould cavity 8 in. deep and a diameter tapering from 5 in. at the top to 4 in. at the bottom. Casting temperatures used were generally in the order of 70" to 90°C above the liquidus and the mould was at room temperature before casting. Inserts kere placed in the mould cavity in some experiments. These consisted of either an 18-g stainless-steel tube of 2 in. diam held axially in the mould i in. off the bottom and extending 1 in. out of the top of the mould or a "trap-door" barrier of stainless-steel gauze of 24-mesh held horizontally in the mould 31/2 in. down from the top. The construction of this insert is shown in Fig. 1. All inserts were preheated prior to casting to prevent chilling. RESULTS The macrostructures of ingots of the three compositions are described, in terms of the three generally recognized zones, in Table I, and illustrated in Figs. 2(a) to (c). The most interesting observation in this table is that relating to the shape of the equiaxed grains, which were not in fact equiaxed but of almost tear-drop shape. Closer examination of these grains showed that each consisted of a head which had a coarse dendritic structure and a tail which always grew in the opposite direction to heat flow, and which had the same structure as that of the columnar material of the ingot concerned; i.e., in the pure aluminum and 0.1 pct Cu alloy it was cellular and in the 2 pct Cu alloy it was cellular-dendritic. Identification of original cast grains was greatly hampered in the super-purity aluminum ingots, and to a lesser degree in the 0.1 pct Cu alloy,

Jan 1, 1968

By J. Evans

Including: Tailings thickeners, CCD?s, paste thickeners, HI-rate thickeners, lamella thickeners, high compression thickeners, clarifiers etc. Flocculant dosing control for mining thickeners and clarifiers is influenced by a number of process factors. 1. Flow rate into the thickener or clarifier a) As the flow rate increases into the thickener or clarifier ?retention time? decreases which causes a greater affect hydraulically on the settling solids. So as the flow rate increases it will generally mean an increase in flocculant dosing rate. b) As the flow rate decreases into the thickener or clarifier the retention time increases which reduces the hydraulic affect on settling, improving settling rates. This will generally mean that as the flow rate decreases, we will decrease the flocculant dose rate.

Jan 1, 2011

By G. J. van der Linde

Foskor operates a mine in the Northern Province of the Republic of South Africa exploiting the igneous complex at Phalaborwa. It produces about 3 million tons of phosphate concentrate per year by means of froth flotation from 26 million tons of ore of which 16 million is mined and milled on site. The remaining 10 million tons originate at the Palabora Mining Company and is pumped as a slurry to Foskor. Two types of ore are mined and milled namely Foskorite and Pyroxenite. (The main mineral content of this ore is Apatite, Phlogopite and Diopside.) After three stages of crushing the ore is milled using 24 rod mills and 5 verti mills. The apatite is then recovered using four stages of froth flotation. The stocks of Foskorite ore are rapidly being depleted and the PMC tailings will also fall away by the year 2002 so that the whole mining operation will then be centered around the Pyroxenite ore. This will lead to substantial increases in production costs. The recoveries achieved in the flotation plant are largely dependent on the successful operation of the comminution section. Parts of this plant are now 35 years old and the advantages of re-engineering, new technology and automation can only be applied to a limited extent in an effort to reduce costs. It was then decided to investigate alternative milling methods, both wet and dry.

Jan 1, 1999

By M J. Saynor, J B. C Lowry

The Ranger Uranium Mine is located in the wet-dry monsoonal tropics approximately 250 km east of Darwin in the Northern Territory of Australia (Figure 1). Mining of open-cut ore bodies commenced in 1980 (Pit 1) and ceased in 2012 (Pit 3) and milling and production are scheduled to cease by 2021. At the conclusion of mining and milling operations, mine tailings will be returned to the mined out pits 1 and 3, which must then be physically isolated from the environment for at least 10,000 years (Australian Government 1999). The final landform also needs to have sufficient mitigation measures in place to ensure that areas downstream are not impacted by erosion products from the mine site. The proposed post-mining rehabilitated landform will cover approximately 847 hectares (8.5 km2) which represents an area that has the potential to supply sediment to catchments and streams downstream. One method of reducing runoff and associated sediment is the construction of rip lines along the contour to slow down the runoff velocity and to also trap fine sediment and nutrients in the depressions to assist vegetation growth.CITATION:Saynor, M J and Lowry, J B C, 2018. The impact of rip lines on erosion at the Ranger Mine Site, in Proceedings Life-of-Mine 2018, pp 150–154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By Carl R. Peterson

[In lTI n,v und I'gr'oun nllnin~ Opt'I'ali n' the high . t cost is the loading and I 3ulage of t tln-of -D"'line ot'. 01' hauling costs can be r duced signifi-cant\v with the us ~ (r \) >It corn'e)'OI' " a COnlTllOn pl'acti c i.n coal and other s 0 t'L rn I n r' a l III i, n e , '. Jf 0 vel s i z ' () f' e can bee 1 i 11.11 tl ate I rH'i 0 I' lO C n v e . in g, ]

Jan 1, 1976

By R. L. Brown

This report, summarizing the Bureau of Mines research and technologic work on coal and coal products for the period July 1, 1950, to July 1, 1951, is based largely on publications issued during the year. The sixteenth in an annual series, it gives footnote references to publications giving further details of the research and technologic work described, except in a few cases where research data presented herein has not been published previously. During the year, the national fuels situation was generally one of plentiful supply.3/ Mineral-fuel resources appeared adequate for several hundred years at reasonably increasing rates of supply. Coal-production capacity was in excess of demand; petroleum supplies were adequate; and natural gas use was limited only by pipeline capacity. However, it was pointed out that a world war would drastically change this situation of relative plenty, particularly with regard to supplies of petroleum and its products. Conversion to the use of coal on a large scale would be required, and improved methods of mining and of processing and using coal in solid or fluidized form or converted to liquid fuels could materially contribute to our national safety.

Jan 1, 1952