Search Documents

By Zachery Zanetell

Flotation circuit performance has become increasingly more challenging due to the complexity of available ore sources. To optimize value mineral recovery, the mineralogical composition of the ore should be evaluated and understood. Utilizing a variety of mineralogical and analytical tools, flotation processing challenges can be overcome and potential limitations understood. In this paper, several case studies will be discussed in terms of the value that has been provided through the use of mineralogical analysis to optimize flotation performance.

By D. Malhotra

Most primary-molybdenite producers use a selective-flotation process in which molybdenite is floated from the ore while other sulfide and non-sulfide gangue minerals are depressed in the same step (Figure 1). The process was developed at the Climax mill. Reagents used in the rougher-flotation stage include vapor oil (collector), syntex (surfactant), pine oil (frother) and occasionally sodium cyanide and Nokes reagent (depressant). Rougher concentrate is upgraded by cleaner flotation to produce market-grade molybdenite concentrates. Reagents used in the cleaner flotation stage are Dowfroth 250, vapor oil, sodium cyanide and Nokes reagent. The development of the flotation reagent scheme at Climax and the role of the reagents have been well described by Born, et al, (1976) and Malhotra, et al, (1976, 1977a, 1977b, 1977c, 1980). The hydrocarbon collector, vapor oil, accounts for approximately 50 percent of the total molybdenite-flotation reagent cost. Because vapor oil sources are limited, and the cost of vapor oil has increased significantly over the last decade, several studies have been done to evaluate alternate oil-based collectors and/or blends of collectors which would produce similar metallurgical results at a reduced cost, or increase the overall molybdenite recovery at the same cost (Smit and Bhasin, 1983; Hahn, 1969; Smith and Bhappu, 1971). The approach taken in the present study was to evaluate alternate non-oil based collectors and collector systems that are less expensive than vapor oil.

Jan 1, 1985

By W. Lodge, G. Rasmussen

"The carbon-in-pulp (CIP) process has been the dominant gold recovery technology since the 1980s. During all this time carbon measurement, and control of the carbon transfer pumps has been largely manual in nature. Such manual operation inevitably limits process efficiency, potentially resulting in higher gold solution losses, and higher cost of circuit operation. Based on the authors’ experience, average plant solution loss is in the range of 0.02-0.03 ppm Au, as opposed to the general industry target of 0.01 ppm Au or less. Gekko Systems, in conjunction with Curtin University’s Gold Technology Group, has developed a carbon concentration meter, the ‘Carbon Scout’ meter. The meter automatically measures carbon concentration in all tanks, providing more frequent and more precise data. Combined with SIMCIL, a CIP circuit process model which is used to determine the optimum set points for the circuit, the meter should ensure lower gold solution losses, and more efficient operation of the carbon circuit. This paper will review they critical factors for good carbon management, the development of the meter and results from the first plant installation. Additional benefits of the Carbon Scout, including improved health and safety and the opportunity to measure other key variables in the leach/adsorption circuit from one central location will also be described.INTRODUCTION The carbon-in-pulp (CIP) process was first introduced to the gold industry in the early 1950s at the Carlton Mill in the USA (Fast, 1988), with the modern version of CIP becoming fully developed with large scale installations in South Africa in the late 1970s (Laxen, 1982). CIP quickly became the technology of choice for new operations, and for the retrofitting or upgrading of existing operations. In the 1980s the carbon-in-leach (CIL) circuit configuration became the process design of choice due mainly to its lower capital costs. With 40 years of operational experience, CIP/CIL for gold recovery is now mature a technology, whose operations and limitations are well understood. To extract further efficiencies from such technologies, by improving recoveries and/or reducing operating costs, is challenging and may require new approaches to circuit management. Gekko Systems, in association with the Gold Technology Group at Curtin University, has developed the Carbon Scout, an automated carbon measurement device. This device replaces manual measurement of carbon concentration in carbon adsorption tanks, providing more frequent and more accurate data for control of the CIP process. Data from the Carbon Scout can be used to automatically control the carbon forwarding pumps."

Jan 1, 2018

By Y Zhou, Y Liu, J-P Yang, P Wang, K Hu

"Large-scale mine reclamation has taken place recently in response to the implementation of mining regulations in China. Effective monitoring of the progress of reclaimed land is a critical procedure to assess the quality of reclamation program and to ensure that mining enterprises fulfill their reclamation responsibilities. The present paper reports a preliminary study that examines the situation of mine land reclamation monitoring. Based on the monitoring, some general requirements for mined land reclamation have been proposed, including: the monitoring should be systematic and comprehensive the monitoring should be adapted to specific local conditions the monitoring should be reasonably optimised via scientific methods and technology the monitoring should stick to a variety of national technical criteria.The aim of land reclamation monitoring is to evaluate changes of critical indicators closely reflecting the development trend of the reclaimed mined land, to develop or improve the criteria and technical parameters specific to the site, and to prevent secondary environmental degradation. Based on these requirements and aim, the monitoring should cover the progress of reclamation, establishment of vegetation and plant community development; and recovery of land and water quality in the reclamation area. Regulatory measures are proposed which would improve the work of mine reclamation monitoring in terms of regulation, organisation and financial support.CITATION :Wang, P, Yang, J-P, Zhou, Y, Hu, K and Liu, Y, 2012. The primary framework for the mechanism of the mine reclamation monitoring in China, in Proceedings Life-of-Mine 2012, pp 47-50 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

By J. E. Golsan

Barrick Gold Corporation installed an expert style control system on the grinding circuit at its Mercur mine. Barrick's main objective was to increase mill throughput by a minimum of 3%. The expert system team collected operating data and then created a knowledge base using Comdale/X expert system development software. The expert system moved from on-line "advisory" mode, testing of expert rules, to full process control in four weeks. Expert system control benefits include a 9-15% increase in mill throughput, consistent mill loading leading to less wear on SAG mill parts, and improved downstream process control.

Jan 1, 1998

By AIME AIME

AT a joint meeting of the Tulsa Geological Society and the Mid-Continent Section of the A; I. M. E., held at Tulsa on March 21, the history of unit development in the Kettle- man Hills field was discussed. Robert C. Patterson? Super- visor for the U. S. Geological Survey at Taft, Calif., was the speaker. An abstract of some of his remarks follows: On July 1, 1923, curtailment agreement for two years was made between the operators of North Dome Kettleman and the U. S. Department of the Interior. In this it was agreed to consider a plan of unit development, or other cooperate method of developing the structure. As a result, Kettleman North Dome Association was incorporated in December, 1930, as a non-profit cooperative corporation under the laws of California. Approved in January, 1931, by California Oil and Gas Supervisor and by Secretary of Interior. On Feb. 10, 1931, it became an active organization through election of executive officers and eleven- directors. General manager chosen. Association started to function April 1, 1931. Assumed control of 10,800 acres of proved and semi-proved land, as shown in Table 1.

Jan 1, 1932

By John T. Ryan

DEFINITE improvement in its accident fatality rate in the coal-mining industry was recorded during 1941, based on preliminary figures for the period from January through October. Total production during this ten-month period was approximately 91 percent of the total production in all of 1940. The ten-month accident rate for both bituminous and anthracite mining in 1941 was 2.15 killed per million tons of coal mined, compared with a rate of 2.66 for the full year of 1940. The bituminous rate decreased from 2.55 in 1940 to 1.99 in ten months of 1941, and the anthracite rate from 3.62 to 3.53 in similar periods. The decrease is more apparent for the bituminous branch of the industry, as the high figure in 1940 was due to seven major disasters which brought death to 276 men. The same number of major explosions during ten months of 1941 caused only 64 lives to be lost. The severity of the explosions has been lower this year but a definite need still exists for reduction in this type of accident.

Jan 1, 1942

By C. E. Williams

THE Iron and Steel Division, A.I.M.E., is unique in this country in that it serves all phases of the iron and steel industries. Through its publications, its meetings, and its sponsorship of new technical developments in the industries, it has proved of great value. The various technical committees of the Division are the nucleus around which this service can be developed. The Blast Furnace and Raw Materials Committee has done excellent work. The need for beneficiation of iron ores is increasing and the economics of this operation are developing more and more in favor of increased activities. Ores that are slightly undergrade should be concentrated up to grade to supplant the present practice of mixing with higher-grade ores to bring up the average composition. Marginal ores that are not now being mined, or that are being mined and piled for future use, should be concentrated. The development of the use of sinter in the blast furnace, because of the elimination of fines, the advantage of better sizing of the charge, the resulting reduction of coke consumption, and increased output of pig iron per furnace, will make concentration and sintering become practical ahead of its natural time.

Jan 1, 1936

By Jan Knobloch

Inter Stand Cooling (ISC) can increase productivity of a HSM and improve final mechanical properties of the strip. Constant Target Exit Temperature can be ensured for the whole strip length eliminating skid marks and other temperature oscillations of the transfer bar. The paper deals with advanced control module of ISC. Essential mathematical models of the control system is introduced and basic functionality is explained. Temperature model is based on FEM. Mechanical and thermal properties of the strip are calculated from chemical composition using neural network. Further on an experimental possibilities for investigation and design of ISC cooling headers will be shown. In conclusion practical experience with ISC on various HSM will be discussed.

Jul 30, 2018

By Lloyd Buckingham

"The operating cost of a gold mine employing granular activated carbon to recover gold can be greatly affected by the condition of in-circuit carbon and its attrition losses. To accurately identify and quantify carbon losses requires careful study. Carbon attrition in the mill can be attributed mainly to physical or mechanical breakage due to the transfer of carbon in the circuit and to carbon oxidation and thermal fracture occurring in the carbon reactivation kiln. Of the equipment involved in carbon transfer, the water powered eductors are the major cause of abrasion and should be replaced with pumps or alternate methods that can serve the purpose. This paper also reviews the impact of carbon stripping and washing on overall operations.IntroductionHolt-McDermott Mine operates a 1360 tonnes per day Carbon-in-Leach (CIL) mill to recover gold. The relatively high carbon consumption and high remaining gold values on carbon after stripping were viewed as a challenging project for research. Extensive metallurgical testwork was initiated to reduce these values. Figure 1 below indicates the carbon flowchart prior to any significant changes in the carbon handling procedures.Carbon consumption after commissioning which was as high as 10""/o of carbon eluted, has been brought down to less than 5%. Changes that brought about this 50% reduction in carbon consumption are:1 ) Improvements in kiln operation2) Elimination or replacement of eductors3) Reduction in tonnes of carbon eluted"

Jan 1, 1994

By C. T. Wallace

Evans Industries, Inc., a management coal consultant and company was assigned to evaluate National Steel Company's coal properties in Knott and Floyd Counties, Kentucky. The results of evaluation showed large reserves of good quality, high volatile metallurgical coal contained in the Elkhorn coal beds and resulted in the formation of Beaver Creek Consolidated Coal Company. Based on results of the exploration and feasibility work, the decision was to install a coal nine, preparation plant and related facilities having a production capacity of one' and three quarter million tons per year with Evans Industries acting as Beaver Creek's management company. The recoverable tonnage assigned to the Stinson Mine is approximately forty-five million tons. This paper discusses the general arrangement of storage, conveying, loading, refuse disposal facilities and the flow sheet of the preparation plant developed by engineers of Heyl & Patterson, Inc., and Evans Industries, Inc., with emphasis on practical flexibility, sulfur reduction in all circuits, and high product yield with the minimum amount of selective mining, Three and one-half miles of railroad have been built by the Chesepeake & Ohio Railroad to service this mine.

Jan 1, 1970

By D White, L. Lorenzen

Sampling and metallurgical testwork during various phases of engineering studies is of paramount importance for a robust processing plant design. When developing a process flowsheet, risks in achieving desirable financial outcomes are minimised by ensuring that appropriate sampling and adequate metallurgical testwork support the engineering and cost estimation at each phase of project development. The quality and type of samples used for metallurgical testwork are just as important as the metallurgical testwork itself. The key characteristic required of any sample is that it represents some defined portion of a mineral deposit. Representivity should consider the spatial orientation, lithology, alteration, degree of oxidation, mineralogy, and competency of the ore such as hardness and abrasiveness. Statistically representative sampling procedures and an appropriate metallurgical testwork program should be designed to bring metallurgical understanding up to feasibility study standard and to give a basis for process plant design. The authors have observed that the quality of sampling and quantity of metallurgical testwork carried out during the various phases of engineering studies are often insufficient to truly support a robust plant design. Some designs are based on benchmarks of apparently similar ore bodies or rely on buoyant metal prices supporting cash flows until rectifications can be implemented. The paper will discuss important aspects of sampling and testwork required for engineering studies in designing process plants. Keywords: Sampling, metallurgical testwork, studies, design

Jan 1, 2020

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the laws of Nicaragua has been prepared from the best available information in Washington , but is released subject to correction and amplification , if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State .

Jul 1, 1930

By Qiang Zhong, Qian Li, Yongbin Yang, Tao Jiang

Thermogravimetric analysis (TGA) has been used to research the pyrolysis and combustion processes of coal used in rotary kiln of iron ore oxide pellet. Furthermore, the effects of air flow and oxygen concentration on the combustion behavior of coal were examined with TGA. The results showed that two individual stages can be distinguished for the pyrolysis of coal, the water evaporation stage and the de-volatilization stage. And the information on ignition and burnout characteristics can be obtained from the combustion process analyzed by TGA. Large air flow almost has no effect to the combustion process except that it enhances combustion intensity. However, the combustion process is further accelerated under oxygen-enriched conditions. With all experimental results, it could provide an attractive approach of analyzing coal for the rotary kiln process.

Jan 1, 2016

Bernard MacDonald, Guanajuato, Mexico (communication to the Secretary*):—Mr. Iceyes's paper is very interesting to me because of my personal experience with the development of the ore-deposits of Lake Valley.

Jan 1, 1909

By T. Banerjee, R. deS. Almeida, D. Gudgeon, F. C. F. Batista, L. deÁ. Silva

"Yamana Chapada’s mine is one of the larger copper-gold mines in Brazil. The mine is located in Goiás state, in the central part of Brazil. The mine has estimated Mineral Reserves of 4.1 million ounces of gold and 3.2 billion pounds of copper as of December 31, 2016. While gold and silver are significant, Chapada’s process flowsheet is configured closer to that of copper facilities. This includes a SAG/Ball configuration for grinding followed by flotation. In the case of Chapada, the mineralogy results in higher-than-normal complexity, notably a significant circulating load both in the grinding and flotation circuits. From an operating perspective, the complexities are controllable, but require careful attention to ensure that circulating loads are effectively managed and gold is not lost to tailings. Chapada created an automation roadmap in 2016 designed to increase plant performance (tonnage, recovery and efficiency). Based on strong potential, the project was fast tracked and within 4 months instruments were installed, control algorithms implemented, and training sessions took place to ensure sustainability at site. This paper will follow the Chapada journey from identifying the opportunities through to implementation and testing.IntroductionYamana Chapada mine is a Copper-Gold mine located in Goiás State, Brazil. Although the mine contains large quantities in Mineral Reserve of gold (4.1 million contained oz as of December 31, 2016), Chapada is primarily a copper mine with copper principally found as chalcopyrite. Accordingly, the processing flowsheet at Chapada is comparable to that of other copper mines with a SAG and Ball mill each partnered with a cyclopack, followed by a flotation circuit. While the overall design is conventional, the mineralogy at Chapada results in significant circulating loads both in the grinding and flotation circuits. This does introduce certain complexities for operating strategies and practices, but, importantly, favourable recoveries and elevated processing rates can be maintained, albeit they need to be closely managed. Plant automation helps in this regard."

Jan 1, 2018

By Xinyang Xu, Chen Zhang, Lixia Li, Zhitao Yuan

"Density functional theory was employed to clarify the mechanisms of the activation of a quartz surface and its collection by the flotation method at the molecular level. The calculation results indicated that hydrogen bonds on the quartz surface (1 0 1) existed in pairs while in contact with water. The simulation was carried out to investigate the different effects of Ca2+ and Ca(OH)+ on a quartz surface with hydrogen bonds, and the results suggested that Ca(OH)+ most likely adsorbed onto and activated the quartz surface. Mulliken population analysis of the external oxygen atom of the quartz surface, calcium atom of Ca(OH)+, and the oxygen atom of oleate showed that there were electron transfer and the formation of a chemical bond between Ca1-O1 and Ca1-O3, which were indicative of strong interactions between the three atoms. In addition, the –OH of the Ca(OH)+ contributed to the activation, which suggested that the Ca(OH)+ group acted as a bridge between the surfaces of oleate and quartz.INTRODUCTIONFlotation is an effective separation method in mineral processing that takes advantage of the physicochemical differences between minerals and gangue, and the properties of the mineral surfaces play a key role in this process (Liu et al. 2016, Qin et al. 2017). In the reverse flotation process of iron ore, gangues are captured by cationic or anionic collectors and floated with air-bubbles as tailings, and the pre-depressed iron oxide minerals are left at the bottom as concentrates (Lima et al. 2013, Yianatos et al. 2015, Zhu et al. 2015). Quartz (SiO2) is one of the major gangues of hematite ores and cannot be easily removed. It is a naturally hydrophilic mineral, in which silicon is the cation in its crystal structure and has very limited solubility. Therefore, quartz must be activated, usually by metal ions, for its effective rejection as a float-product by reverse flotation (AIME. et al. 1976)."

Jan 1, 2018

By M. Lindgren

"Hydrometallurgical processing involves process stages, like leaching, that create harsh environment for stainless steels. High acidity, the presence of chlorides and oxidizing ions combined with relatively high temperature create risk for both uniform and localized corrosion. Advanced electrochemical techniques were employed to study uniform and pitting corrosion of two stainless steel grades 316L and 2205. Results obtained with the linear polarization resistance technique combined with the harmonics distortion analysis, electrochemical noise and coupled multielectrode array systems are compared to the results of conventional electrochemical techniques and immersion tests.INTRODUCTIONHydrometallurgical processing has become favoured in metals production in recent years due to energy costs, leaner ore bodies and environmental factors. Because the hydrometallurgical processing route is flexible, various types of secondary raw materials, like flotation tailings, dusts, sludges and slimes can also be treated in addition to conventional mineral concentrates (Sarveswara Rao & Acharya, 2008).Hydrometallurgical processing relies on aqueous chemistry, usually acids, at temperatures around 100°C for the recovery of metals from ores, concentrates, recycled or residual materials. The processing route can typically be divided into three stages: leaching, solution concentration/purification and metal recovery. The processing environment is aggressive, especially in leaching. High acidity, relatively high temperature together with impurities, like chloride ions, place high demands on the corrosion resistance of construction materials. The dominant corrosion mechanism may be uniform corrosion or localized corrosion depending on the process conditions (Ekman & Torsner, 2010). This complicates the prediction of corrosion rates and, consequently, cost effective material selection.Traditional means to evaluate uniform corrosion resistance of stainless steels are immersion tests and the results are published in the form of iso-corrosion diagrams (Outokumpu Stainless, 2010). For the localized corrosion, namely pitting and crevice corrosion, immersion tests can be used but the duration of the test is rather long because an incubation period takes place prior to the occurrence of the actual localized corrosion damage. Electrochemical techniques, traditionally in the form of cyclic polarization scans, have been employed to assess the susceptibility of a material to pitting corrosion (Papavinasam, 2008). They cannot, however, give any indication of the pitting corrosion rate and lack potential for on-line measurements."

Jan 1, 2012

By Y Xu, J Hacker, D J. Williams

Shear strength parameters of compacted clay liners are needed to analyse the stability of mine waste dumps containing compacted clay liners as sealing layers for potentially acid forming waste rock. A representative clay sample was supplied by McArthur River Mine from the mine site in the Northern Territory, Australia, with an average as-supplied gravimetric moisture content of about 13.6%. The clay was compacted in a 100 mm by 100 mm direct shear box at the as-supplied moisture content to a dry density of 1.85 t/m3, representing the field compaction specification adopted by the mine. To determine the peak and ultimate shear strengths of the compacted clay, single-stage direct shear testing was carried out at nominal initial normal stresses of 50 kPa, 100 kPa and 200 kPa, representing shallow depths of burial in the North Overburden Emplacement Facility of about 2.8 m, 5.6 m and 11.1 m, respectively (assuming a waste rock wet unit weight of 18 kN/m3). Three shearing rates of 1 mm/min (rapid), 0.1 mm/min (intermediate) and 0.01 mm/min (slow) were applied to study the influence of shearing rate on shear strength. In addition, the development of a residual shear plane was tested by reversal and re-shearing in the direct shear box. In the first shearing, the peak and ultimate shear strengths are determined. The normal load was then removed and the box rewound to its starting position. The normal load was then re-applied and the specimen re-sheared. Two reversals were applied to each specimen, and it was found that there was no significant reduction in shear strength. Finally, based on a range of shear strengths obtained in the laboratory for McArthur River Mine clay and other materials by various laboratories over time, shear strength parameters for the compacted clay were recommended for use by the mine.CITATION:Xu, Y, Williams, D J and Hacker, J, 2018. Shear strength of compacted clay liner at McArthur River Mine, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 208–219 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By D. An, J. Withers

A nano-scale investigation has been carried out by applying an AFM (atomic force microscope) to study in situ the adsorption of various collectors, i.e., oleic acid, octanohydroxamic acid (HA), and salicylhydroxamic acid (SHA), on bastnaesite in aqueous solutions. The obtained AFM images show that the surface morphology of bastnaesite changes greatly after it contacts the solutions of the collectors, suggesting that all these collectors can effectively adsorb on bastnaesite. Increasing temperature can help increase the adsorption of oleic acid on bastnaesite. FTIR (Fourier transform infrared) results also show that all these collectors adsorb strongly on bastnaesite with a strong absorbance spectra being detected, which confirms with the results obtained with AFM imaging analysis. In general, hydroxamic acid collector (HA and SHA) adsorbs on bastnaesite mainly in the form of insoluble metal hydroxamate. This specific adsorption mechanism explains that a high selectivity with a moderate collectivity will be achieved with a hydroxamic acid collector for the flotation of bastnaesite. INTRODUCTION Rare earth metals, which are very important to modern industry, are generally extracted from numerous rare earth minerals. In practice, however, the actual extraction of rare earth is mainly from bastnaesite, monazite and xenotime. The Mountain Pass mine is one of the largest rare earth mine in the world, at which the main rare earth mineral is bastnaesite. In the past years, froth flotation has been applied to the beneficiation of Mountain Pass ore. In practice, the rare earth ore is usually crushed, milled and further separated from calcite, barite and other gangue minerals by froth flotation, in which the rare earth oxide-bearing minerals stick to aerated bubbles in the pulp and float to the surface, leaving the gangue at the bottom of the flotation cell and disposed of as tailings.(Bulatovic, 2010) In spite of the fact that froth flotation has been applied to treat the bastnaesite ore at the Mountain Pass mine, the rare earth oxide (REO) recovery is still low,(Anderson, 2015) especially compared to the one obtained with sulfide flotation. For example, the typical recovery obtained at the Mountain Pass mine was only about 70%. This may be due to the low selectivity of the collector (oleic acid). In addition, to enhance the flotation selectivity, the pulp in the mine circuit has to be heated up to 70 to 90°C and it involves a lot of energy consumption. Last but not the least, a lot of depressants have to be added to improve the selectivity of flotation process. Therefore, it is critical to re-examine the existing flotation process at the Mountain Pass mine and seek any chance of improvement. (Anderson, 2015)

Jan 1, 2019