Search Documents

By Laxman (Lucky) Amaratunga, Hisham Madi

Final disposal of mine wastewater neutralization sludge continues to be one of more pressing problems in the mining industry. The disposal of mining and metallurgical waste products into underground reduces the environment impact and improves the safety of the mining operation and the economics of the enterprise. This current research focuses on an investigation of utilization of mine wastewater neutralization sludge obtained from Kidd Creek Mine site, as a supplementary material for their proposed deep mine pastefill system. Their proposed pastefill consist of combination of rock aggregate in a matrix of imported sand and tailings with binder (Portland cement + Slag cement). Pastefill mixes containing various percentages of the waste sludge 0 (control mix), 1, 2, 3, and 5% by weight as replacement to the fine sand were prepared and tested with different percentages of binder. Hypothesis behind this approach is to study the behavior of sludge as replacement of sand in matrix as well as its ability to act as a binder. Compressive strength, percentage of sludge, binder dosage, slump, water to cement ratio, percentage of solid, and curing time are being observed. The results indicated that sludge can be incorporated into the pastefill and enhance its strength without compromising the pastefill quality and integrity.

Jan 1, 2004

By W. L. Freyberger

In a study of the kinetics of flotation of coal, employing a single-cell continuous flotation system, Jowett and Safvi1 pointed out that it was experimentally impossible to float all of the coal which could be floated in a batch tests. On the other hand, deBruyn and Modi, in a discussion of their paper, suggested that under certain conditions the recovery of floatable material from a similar one-cell continuous system would have been 100%.2 Both of these pairs of authors make the assumption that a state of perfect mixing exist in the flotation cell. This assumption, usually made by investigators studying flotation kinetics in a continuous system, has been confirmed experimentally on several occasions. The work is summarized by Arbiter and Harris.3 It is the purpose of this note to demonstrate that, for conditions of perfect mixing, one of two conditions exist: 1) the recovery of floatable material is 100%, and the flotation is infinitely fast, or 2) the recovery of floatable material must be less than 100%. This theorem can be proved simply in the following manner: 1) If recovery, R, of the floatable material is 100%, the concentration in the tailing must be zero. This follows from the definition of recovery as

Jan 1, 1964

By Robert A. Jankowski, John J. McClelland, Charles Babbitt

The purpose of this study was to develop guidelines to enable mine operators to maximize longwall dust reductions, while optimizing the use of ventilating air and shearer water consumption. A recent investigation by Foster-Miller Incorporated, under a Bureau of Mines contract, quantified the effect of increased face airflow and shearer water supply on face dust concentrations. A 70 pct reduction in respirable dust levels was achieved at the shearer operator's position during tail-to-head cutting by an incremental increase in average face air velocity from 83.8 m/min (275 fpm) to 123.4 m/min (405 fpm), while holding shearer water consumption constant. A 60 pct reduction was achieved through an increase in shearer water pressure and flow from 9.1 kg/cm2 (130 psi) at 0.19 m3/min (50 gpm) to 19.7 kg/cm2 (280 psi) at 0.28 m3/min (75 gpm), holding airflow constant. The combined effects of increasing both parameters produced an 85 pct reduction. Optimal usage of ventilating air and shearer water consumption can be achieved by defining a "point of diminishing returns" above which further increases no longer reduce dust concentrations, proportionately .

Jan 1, 1987

By H. Bernatowicz

The Nucoalyzer (On-Line Nuclear Analyzer) is a new method recently made comercially available for monitoring the elemental composition of a process stream. Applications for the Nucoalyzer include grading ore on a conveyor belt before or after it has gone through primary crushing, monitoring the slurry being transported in a pipe to the concentrator, and monitoring the stream of concentrate or the tailings from the concentrator. The Nucoalyzer may also be used at the smelter to monitor elements in the feed that include copper, sulfur, iron and silicon where a uniform feed is desired. The advantage of the Nucoalyzer over most other techniques are (a) it performs the measurement directly on the process with no sampling necessary, (b) the analysis can be performed on streams of particulate and slurries, and (c) the system does not have to make contact with the material it measures. These Nucoalyzers are operating at coal fired power plants and several more are about to be placed in service. This paper discusses the principles of operation of the Nucoalyzer, our experience in the field, application of minicomputers to data reduction, and potential applications in the ferrous and non-ferrous industries.

Jan 1, 1982

By Frank Firmstone

The indicator cards shown herewith were taken by the writer in June, 1877, from the water-pressure blowing engine of the Longdale Iron Co., at Lucy Selina Furnace, Longdale, Virginia. A description of' this engine with figures, and some indicator cards, was published by Washington Jones, Esq., Superintendent of the I. P. Morris Co.,* in the Journal of the Franklin Institute for May, 1877, to which those desiring a full account are referred, but for convenience the principal dimensions, etc., are given below. The machine consists of a pair of horizontal direct-acting blowing engines, connected at right angles to a common fly-wheel shaft. The blowing cylinders are 4 ft. diameter by 5 ft. stroke; the water cylinders were 18 in. diameter by 5 ft. stroke as built. Both water and blowing cylinders are double acting. The water valves are balanced piston valves, 18 in. diameter, moved directly by eccentrics on the fly-wheel- shaft. Great care was taken to have the areas of the ports and passages at least equal to the area of the working piston. The engine is set about 14 ft. above the tail-race, and the

Jan 1, 1879

By E Villaescusa

This paper summarises research work carried out at the Western Australian School of Mines on mine backfill properties in the last few years. The fill properties presented relate to cemented aggregate fill and cemented tailings fill. Emphasis of these studies has been placed on the composition of backfill materials including aggregate particle size distribution, cement dosage and influence of cement admixtures. The unique features of the backfill research carried out at WASM during the last few years are the accomplishment of a study into the properties of large cemented rockfill samples by triaxial testing and the investigation of the properties of fill material made from highly saline ground water prevailing in the Goldfields region of Western Australia. Exploring different cost-effective binding agents for mine backfill was also carried out at WASM. Special effort has been put on the development of fill materials compatible with hydraulic and paste fills. During the process, specific methods and procedures for laboratory testing of backfill material have been formalised. The on-going backfill research on sample scaling is summarised and the future direction of WASMÆs backfill research focus is outlined.

Jan 1, 2000

By John Stroiazzo, Bernard C. Aubé

Brenda Mines, located 22 km Northwest of Peachland in British Columbia, Canada was an open pit copper- molybdenum mine which closed in 1990 after 20 years of operation. The primary concern in Brenda's tailings and waste rock drainage is molybdenum at a concentration of approximately 3 mg/L. The mine drainage is alkaline and contains little or none of the typically problematic heavy metals. Given that the waters downstream are used for municipal water supply and some irrigation, a discharge limit of 0.25 ma molybdenum was imposed with specific water quality guidelines in the receiving creek. A review of all existing and potential molybdenum removal methods was undertaken prior to mine closure. The chosen process is a two-step iron co-precipitation with clarification and sand filration at a slightly acidic pH. A 4,000 usgpm (912 m3/h) treatment plant was constructed and commissioned in 1998, at a cost of $10.5M. The successful removal of molybdenum from the drainage water is explained with details on some design innovations and operational challenges encountered during plant start-up. Investigated sludge disposal options are discussed although the long term disposal scenario has not yet been finalised.

Jan 1, 2000

By Muhammad Zaka Emad

Cemented rockfill (CRF) plays a vital role in pillar-less mining. Many factors are associated with optimum design of a CRF material. Factors like strength, placement method, mixing, curing time, water content, binder contents, binder composition and additives require to be studied for appropriate rockfill design. The most important factor is strength of a CRF. The design engineer considers fill strength requirements (FSR) for the estimation of CRF strength requirements. Inappropriate CRF strength can cause excessive ore dilution. The recent studies on CRF practices at some of the Canadian mines revealed the most common flaws. Comparison of different types of fill determined that most of the failures occur in cemented rockfill, and the compressive strength can be improved by small addition of sand and mine tailings. This work discusses the studies on determination of unconfined compressive strength, Young?s modulus, density and water contents of CRF being placed in the excavated stopes. It was found that the CRF properties were largely influenced by the variation in gradation and curing time. The 7% binder content improved compressive strength of rockfill significantly but it has an influence on the economics, whereas 4% and 5% binder contents are better choices. The maximum Young?s modulus values were obtained at 28 days curing time for most of the samples.

May 1, 2011

By Jaye Pickarts, Bret Boster, Jack McPartland

Pegasus Minera de Chile, Ltda. is completing three phases of metallurgical evaluation on the Pullalli project to develop a preliminary process flowsheet. A project feasibility study is in progress. The feasibility study includes a proposed process flowsheet designed based on results from the multiple stages of metallurgical evaluation. Phases I and II of metallurgical evaluation included laboratory scale heap leach and milling cyanidation testwork on multiple drill core composites and bulk ore samples from the Pullalli Project. Phase Ill included pilot scale milling/cyanidation testwork on Pullalli drill core composites. The proposed flowsheet includes selective mining and separate processing of low grade and high grade ores. Low grade ore will be crushed and heap leached. High grade ore will be milled leached for 12 hours in an agitated cyanidation circuit. After 12 hours of leaching, sands and slimes will be separated and the sands will be washed using a counter current cyclone (CCC) circuit. Partially leached and washed sands will be added to the crushed low grade ore for heap leaching treatment and permanent placement. Partially leached slimes will be thickened in a high capacity thickener and will be processed in a CIP circuit. Leached slimes will be placed in a tailings impoundment.

Jan 1, 1996

By C Chen, W J. Bruckard, F R. A Jorge

The base metal industry mines and processes hundreds of million tonnes of ore per annum to produce saleable products and large tonnages of waste by-products such as tailings. These ores usually contain less than 1 wt per cent of toxic elements (As, Sb, Bi, Cd, Se, Te, Hg, etc), which are subsequently treated with the other components in the ore during the production of concentrate through to saleable metal products. The deportments of minor elements across the various unit operations of a process flow sheet do not normally receive the attention that the major elements receive. However, these minor elements can have a major influence on the quality of the products as well as an economic and environmental impact. Therefore, a high degree of control over their deportments is a key step in reducing their dispersion in the biosphere. Ongoing work at CSIRO has been examining minor element deportments across unit processes used for smelting and refining and the options for early removal of minor elements, as well as methods for safe disposal of some toxic elements. This paper provides an overview of the R&D activities undertaken at CSIRO to develop tools and methodologies for improved management of minor elements during the processing of sulfide ores.

Jan 1, 2006

By M. Di Tommaso

Acid Mine Drainage (AMD) is a quite diffuse environmental problem in dismissed sulphur mine districts. AMD is related to sulphur oxidation of abandoned tailings, generating heavy metal-bearing streams with high iron and sulphate contents and low pH. Treatments of AMD aim firstly to increase the pH to reduce its leaching power causing the further release and mobilization of heavy metals through soil solution and groundwaters. Increasing the pH also allows the precipitation of iron (III) (involved in sulphur oxidation and then in AMD generation) and the partial removal of other toxic components such as arsenic. pH adjustment and the reduction of the high concentration of iron are also necessary for the successive biological treatment in permeable reactive barriers (PRB) with sulphate reducing bacteria (SRB) (II step, biologically mediated precipitaton/biosorption) to avoid the rapid plugging of the barrier (for the large amounts of iron precipitates) and to ensure neutral pH conditions for SRB growth. In this work the first step (chemical precipitation) of a combined chemical and biological treatment of AMD is presented. Experimental data from column tests using carbonate stones to remove iron and increase pH were reported. Toxicity tests have been carried out on the treated wastewaters by Lepidium sativum.

Jan 1, 2006

By Steve Rule, Jose Roberto Vago, Walter de Moura

Cerro Vangaurdia Gold Mine is a joint venture between AngloGold (the operator), Perez Companc and Formicruz and is situated in the southern province of Santa Cruz, in Argentina, approximately 2,150 km south of the capital, Buenos Aires. The mine is located in a severe, semi-arid environment with very cold winters and little annual rainfall (200mm). It is an open-pit operation, mining several narrow, shallow epithermal quartz veins with . gold and silver mineralisation. Commissioning of the plant commenced in September 1998 and the first dore bar was poured towards the end of the same month. The nominal capacity of the plant is 55,000 tonnes per month, with a design capacity of 60,000 tonnes per month. Prior to finalising the design, an extensive testwork programme was undertaken at Nova Lima, in Brazil, in which all parts of the process were evaluated together on a pilot-plant scale. The process flowsheet selected at Ce1rn Vanguardia is quite novel, in that it includes milling in cyanide, as well as a cyanide recovery and recycling plant on the tailings section of the treatment plant is included. The cyanide recovery process selected was a version of the acidification - volatilization - reabsorption (AVR) process, known as Cyanisorb™. The selection of the Cyanisorb™ process in the plant design was as a direct consequence of two factors:

Jan 1, 2000

By J. R. Dartez

The use of CCD (counter current decantat.io;1) thickeners, or; clarifiers, in the gold mining industry is quite common. Although there are a number of technologies in the industry which utilize these types of tanks, the fundamental requirement is to settle leach tailings and eventually separate gold and silver "values" from the "barren" (no values) solution. The thickener separation process varies depending upon the raw ores found in any specific mine. In mines where rudimentary, rocky ores are most common the settling process is fairly straight-forward and uncomplicated. But, for those mines with complex carbonaceous ores, usually identified by high silting, clay components, the ability to monitor and control the settled materials is quite laborious and costly. The task of monitoring and maintaining control of settled residue in clarifiers and thickeners, of any design, is difficult in any industry, but due to the added desire in the gold mining industry of leaching the values from the liquid slurry, the problem is multiplied. Other common activities taking place in the thickeners are exaggerated internal flow rates, settleable solids activity due to rake movement, and the settling activity generated by flocculents being added to the liquid medium. All of this action within the liquid column causes the continual monitoring of the interfaces within the tank close to impossible.

Jan 1, 1993

This paper describes an investigation of the sampling problems which contributed to erroneous Concentrator production forecasts at the mining operation of Bougainville Copper Ltd (BCL) in the North Solomons province of Papua/New Guinea.Reference figures provided by independently verified commercial shipment data demonstrated the existence of a bias in the calculated Concentrator production; the challenge was to identify systematic errors in each of the contributory measurements (feed tonnage and feed, tailings and concentrate grades).The uncertainty surrounding specific sampling and measurement errors precluded optimum metallurgical control and performance of the milling circuit, encouraged disputes about the difference between Mine versus Concentrator production estimates, and cast some doubt on efforts to follow political guidelines concerning a maximum feed tonnage or recovery oriented mill operating concept.An evaluation of routine results as well as specifically targeted test work identified the sampling errors associated with measured individual parameters.The emphasis in this report is on the procedure for quantitative error assessments.The measured performance of a mineral dressing plant is subject to a systematic error balance which can be derived from the more familiar weight and metal balances such as the two- or three-product formula.The resulting equations are generally valid, and they are applied to the measurements obtained at BCL's Concentrator to illustrate the method.

Jan 1, 1976

By Quan Li, Xiang Ren, De Lui, Yumin Zhang

SL-type continuous centrifugal separator with injection flow (Injection Flowing Film Centrifugation, IFFC) for separating fine and ultra-fine minerals has been developed recently in China and it is capable of recovering particles down to one micron in size. In this paper, the principle of its separation is discussed. IFFC is a special transient pulsating film which combines both thin film jigging and thin film concentration functions. It not only can intensify the looseness and stratification of the settled particles, but also create a hydraulic weir effect to improve recovery of fines and ultra- fines and significantly improve the performance of thin film separation. In a Chinese tin gravity concentrator, SL devices, SL-1200s (capacity 1.5-2.0 ton/hr) and SL-600s (capacity 0.5 ton/hr) were applied to treat -1 0 micron cassiterite slime(removed as tailings at the past) and to replace the old tin flotation system(-74+10 micron slime). The plant results show that 50-60% of the cassiterite can be recovered from -10 micron slime with an enrichment ratio of 10-12. Particle down to one micron were recovered. Under optimal conditions, the recovery from -74+10 micron slime can reach more than 85%. The recoverable size range can be determined by calculation.

Jan 1, 1995

The flotation circuit handling Peko ore at Peko Mines N.L. was examined in July 1970 with a view to determining simple changes in circuitry or reagents which could improve the grade and recovery of the final copper concentrates. The investigation included sampling over one shift followed by detailed testing of the samples by sizing-assays, sizing-mineralogy and sizing-liberation. Mass balances were carried out over total streams, the component minerals and the copper contents. Some laboratory work was carried out to assess the effect of salinity on flotation. In order to handle the sizing-mineralogy calculations a computer programme was set up. The raw data were corrected for locking factors, then mineral and elemental distributions cal- culated for each screen fraction and the total sample. Calculated assays from grain counting were compared with chemical assays. Recoveries through the size-ranges re- vealed very rapid flotation of copper minerals at sizes below 350 mesh. This pointed to a possible circuit improvement by desliming rougher tailings ahead of the scavenger stage. A strong correlation was found between water in concentrates and gangue recovery for the subsieve sizes. This pointed to clean water additions to the cleaner circuit as a way to 1 Project Consultant, The Australian Mineral Development Laboratories, Adelaide, South Australia.

Jan 1, 1972

By A. T. Tye

WHEN the roughing tables operated in 1923 were abandoned, all the coarse iron pyrite for-merly removed by the tables had to be ground to flotation size, which caused an increased power con-sumption of 2 kw.-hr. per ton. Recently, by increasing the tonnage, this has been reduced to a total of 16.6 kw.-hr. per ton. The cost of repairs has been slightly reduced by using an alkaline circuit instead of the acid mine water used in 1923. Other economies from elim-inating roughing tables and the finishing tables have more than compensated for the extra grinding and the total costs have remained practically the same, until the first part of 1927, when, with increased tonnage, the total cost has decreased to 72 cents and the repair cost to 9 cents. In 1923, with a combined gravity and bulk flotation flowsheet, the grade of concentrate was only 4.38 per cent copper. With preferential flotation this has in-creased to over 17 per cent copper. The tailing has decreased from 0.29 per cent -copper to 0.18 per cent. The copper recovery, instead of decreasing; as might be expected, has increased from 87.4 per cent to, 91.5 per cent. The silver recovery has also increased from 88

Jan 8, 1927

Ion Exchange is finding a greater role in copper processing, and hydrometallurgy in general, both as a technique for removing impurities and as a means of adding value through the recovery of secondary metals. Both the gold and uranium industries use resin adsorption as a primary production technique. While hydrometallurgical processes predominantly rely on solvent extraction as the mainstay of copper recovery there are a number of projects, in particular polymetallic deposits, which are considering the use of resin recovery as an alternative or supplemental production technique. A number of applications have been developed and proven at commercial scale for the removal/control of impurities (iron, antimony and bismuth) from copper electrolytes. These are well documented ion exchange applications. Increasing metal values and scarcity of certain metals are focusing companies to look at secondary metals recovery rather than losing these often highly valuable metals to tails residues. Bleed streams are being seen as valuable opportunities to recover contained metals; iron, copper, nickel, cobalt, bismuth, antimony and rhenium are all metals being targeted for removal or recovery from process solutions, electrolytes and bleed streams. An overview of currently applied techniques as well as some developmental technologies for impurity removal and secondary metals recovery is presented to provide insight into the advantages and flexibility of ion exchange applications in metals processing.

Jan 1, 2007

By E. A. Devuyst, G. Robbins

A unique process for removing cyanide and base metal complexes from industrial waste streams was patented by G.J. Borberly et al. (1984). The process uses SO2 (liquid or gas, or solutions of sulfite salts, or from burning elemental sulfur), plus air that is dispersed in the effluent using a well agitated vessel. Acid produced in the oxidation reactions is neutralized with lime at a controlled pH generally in the range 7 to 10. The reaction requires the presence of soluble copper as a catalyst which can be supplemented by copper sulfate if necessary. The process can be applied to the detoxification of gold and silver mining waste streams, such as carbon-in-pulp (CIP) tailing pulps, barren solution bleeds, pond waters and heap leach rinse solutions and also to plating shops wastewaters. The SO.jAir process has substantial advantages over two of the main alternative methods of cyanide destruction, namely alkaline chlorination and hydrogen peroxide. Alkaline chlorination is highly penalized in terms of reagent consumption. Chlorine is a strong oxidant reacting with species other than cyanide present in the effluent such as thiocyanate and sulfides. Furthermore alkaline chlorination is an incomplete detoxification process. Iron cyanide is not removed and the potential for harmful by-products species exist. Consequently final effluents may be subject to additional treatment in order to comply with regulatory demands.

Jan 1, 1991

By M. C. Van Camp, J. D. Miller

Preliminary results are reported regarding the design and development of a pilot scale air sparged hydrocyclone for cleaning fine coal 590 pm (- 28 mesh) containing 24% ash and 1.6% sulfur. The principle of separation is the flotation of hydrophobic coal particles in the centnjugal field generated by the fluid flow in the air sparged hydrocyclone as discussed in another publication. This 152-mm (6-in.) hydrocyclone has a nominal capacity of 0.9 t/h (1 tph) and experimental results suggest that separations vastly superior to a water-only cyclone are possible. In addition the separation efficiency is as good, if not better, than that achieved with conventional flotation cells. For example, typical results indicate that 75% clean coal can be recovered at 15% ash leaving a tailing product of almost 50% ash. These experimental results coupled with the high capacity of the air sparged hydrocyclone (imagine a retention time for flotation of only two seconds compared to two minutes for conventional flotation) may represent a significant breakthrough, not only in coal preparation technology, but in the flotation of fine particles in general.

Jan 1, 1983