Search Documents

By G. Meiers, M. O’Kane

Dry cover systems as a closure option for management and decommissioning of waste rock and tailings is a common prevention and control technique used at numerous sites around the world. Numerous site-specific factors control the long-term performance of dry cover systems. Site-specific climate conditions are one of the key factors to consider when determining the objectives of a dry cover system because these conditions will significantly influence long-term performance. There are advantages and disadvantages of characterizing the site on an annual basis as generally a “dry” site (annual potential evaporation greatly exceeds annual precipitation), or generally a “wet” site (annual precipitation meets or exceeds annual potential evaporation). The field performance monitoring data and discussion presented herein illustrates the caution that is required when using these “annual” criteria for characterizing site climate conditions. Numerous sites exist where precipitation exceeds potential evaporation on an annual basis; however, the site typically experiences hot, dry summer months where evaporation greatly exceeds rainfall. These dry summer conditions have a strong influence on long-term performance. In contrast, sites where potential evaporation exceeds precipitation on annual basis, typically experience periods of the year when a moisture surplus occurs, which also impacts on long-term performance. This paper uses soil-atmosphere cover design modelling and field performance monitoring from sites in Canada, Australia, and the United States to demonstrate the importance of considering site-specific climate conditions when predicting long-term cover system performance.

Jan 1, 2003

By Evans A. F

Arising out of the increasing demands for efficiency in modern ore-dressing operations has grown a requirement for fuller knowledge of the characteristics of the ore treated. In part, this is being met by improved methods of study of the mode of occurrence of the constituent minerals, and of the intricacies of their physical relationships.A typical instance of the need for such a study is the presence of some undesired mineral in a flotation concentrate or tailing, which may be due either to mechanical association through insufficient grinding, or to incomplete separation in the flotation operation.Again, with modern practice in fine grinding, which often requires that from 70% upwards of the ground ore shall pass a 200-mesh screen, it is obviously impossible to obtain data on comparative grinding efficiencies, for instance, unless there is adequate knowledge of the size-composition of the material passing the finest available screen.Studies like these can be made satisfactorily only after size-separation (which may be carried out conveniently by elutriation) and by actual visual examination with the aid of a microscope, and the minute size of the mineral grains to be examined has necessitated the development of a new technique of sizing and microscopic examination.

Jan 1, 1932

By Hamid-Reza Manouchehri, Hassna Aitahmed-Ali, Stellan Sundberg

"In flotation practices as the particle size becomes fine, e.g., p<20µm, the process efficiency declines markedly. When flotation of fine particles is necessary, one method to improve the recovery is selective agglomeration of fines. Different agglomerating methods have been introduced and tested; however, one method which has recently received great attention is to aggregate fine particles by magnetic force. A selective aggregation of the fine paramagnetic particles, e.g., sulfide minerals, can be achieved by applying a high intensity magnetic field during flotation conditioning. The method is simple, selective and effective for fines, and has a low operation cost. However, a minimum magnetic susceptibility of fine grains is required for this process. This method has been demonstrated in different sulfide minerals flotation plants. The implementation of the magnetic conditioning device, ProFlote, in both the Cu-Pb and the Zn circuit of Boliden’s Garpenberg plant in Sweden, where a complex massive sulfide ore is treated, is discussed herein. The preliminary results have shown an increase in the recovery of value minerals, in particular Zn and Ag and considerable reduction in Zn deportment to the final tail. Increases in Cu grade and decreases in Pb grade in Cu-con have been achieved as well."

Jan 1, 2014

By R. S. Shoemaker, F. W. McQuiston

CARLIN GOLD MINING COMPANY 1974 Operating Data to October MINE LOCATION: 40 miles from Elko, Nevada ORE DESCRIPTION: Gold with minor amounts of mercury occurring in siltstone and carboniferous limey shales. TYPE OF MINE: Open pit ORE HAULAGE TO MILL: By trucks up to a distance of 12 mi1es MILLING CAPACITY: 2500 tons per day ORE GRADE: 0.20 oz per ton oxide ore 0.25 oz per ton carbon type ore PRODUCTS: Gold bullion 993 fineness, by product quicksilver RECOVERIES: Oxide ore 887&apos;0 Carbon ore 83% POWER FOR GRINDING: 7 Kwh/T POWER, other than grinding: 14 Kwh/T WATER SUPPLY: Pumped from wells 2- 112 miles through 13,000 ft of 8" buried pipe 6 ft underground. Consumption 0.60 tons of new water per ton of mill feed. TAILINGS: By 10" woodstave pipe a distance of 2500 ft to mine waste filled dam. RUNNING TIME: 10 ft x 10 ft mill on oxide ore, 98% 7 ft x 8 ft mill on carbon ore, 937&apos;0 Principal causes of lost time, power outages and problems of feeding gaseous chlorine to carbon ore agitators. LABOR, TONSIMAN SHIFT: See detailed data sheet ILL BUILDING DESCRIPTION: Framed structural steel with sandwich type walls of marine plywood, then packaged pre - fabricated insulation and outer sheeting of galvanized corrugated steel.

Jan 1, 1975

By S Ellis, J McMullen, M Habner

A new leaching regime was implemented at Kalgoorlie Consolidated Gold MinesÆ (KCGM) Gidji plant on a cyanide leach of ultra-fine ground sulfide concentrate. High lime concentration and lead nitrate were used to overcome the refractoriness of the fine sulfides (high reactivity of fine sulfides with the presence of gold tellurides). The leach pretreatment stage was shown to be detrimental and was shut down. Lime titration was introduced as part of the process control. It was shown that the leach could be performed at low dissolved oxygen, (ie 3 - 5 ppm) to avoid sulfide oxidation and the associated high cyanide and lime consumption. Plant results showed reduced cyanide consumption (40 per cent) and an accelerated leaching rate, whereby most of the gold was dissolved in 24 hours compared to 72 hours used previously. Similar work was performed at KCGMÆs Fimiston plant, which leached a combined ultra-fine ground sulfide concentrate along with the slimes fraction from hydrocycloning the bulk flotation concentrate. The use of lead nitrate, high lime and carbon-in-leach generated a faster leaching rate and minimised adsorption of gold on fine pyrite particles. The grind, previously controlled with a P80, was replaced by a P98 to give a better operational indication of top size hydrocyclone performance. Before the implementation of the changes, average leach residues for slimes and UFG were respectively 4.0 g/t and 5.5 g/t. With the modifications to the leaching regime, average leach residues were lower by 1.5 - 2.0 g/t. Whilst significant improvements have been demonstrated, further work is progressing at KCGM to further reduce ultra-fine concentrate leach tail grades, and also to improve the understanding of concentrate refractoriness and the factors responsible for differences between laboratory and plant leach results. Estimated profits since the implementation of the new approach are in the range of $A3.5 million per year.

Jan 1, 2005

By S R. Grano, M Vera

This paper deals with two separate case studies investigating the froth phase performance and characterisation of two industrial rougher/ scavenger flotation circuits. Froth phase performance was quantified using a mass balance approach to estimate froth zone recovery. Measured characteristics of the froth phase included frother solution concentration determined by gas chromatography, and the time taken for an equilibrium froth sample to decay to one-half of its original froth height. The latter measurement is referred to as the æfroth half-lifeÆ and is strongly linked to froth stability. Special methods and techniques developed to preserve frother in solution and to measure froth half-life are briefly described. The frother type in the first case study was a mixture of straight and branched alcohols, whilst the frother type in the second case study was a mixture of alcohols, aldehydes and triethoxybutane. The first case study focussed on a flotation circuit treating a low-grade ore containing only a small fraction of floatable copper sulfide minerals, while the second case study focussed on a flotation circuit treating a higher grade complex sulfide ore containing significant quantities of chalcopyrite, galena, sphalerite and pyrite. It was found that froth zone recovery of valuable mineral generally decreased down-the-bank of the two industrial rougher/scavenger circuits. Moreover, decreases in froth zone recovery significantly limit the overall cell recovery of valuable mineral achievable from the plant scavenger cells. However, the decrease in froth zone recovery could not be linked to the removal of frother from the pulp solution to the concentrate product in the preceding rougher flotation stages. Measurements of residual frother in solution suggested that, approximately, only five to ten per cent of the added frother was removed into the rougher/scavenger concentrate, with the remainder appearing in the scavenger tailings. This finding suggested there was apparently adequate frother in solution in the scavenger stages.

Jan 1, 2005

By Andrea R. Gerson, Roger St. C. Smart, Russell Schumann, Joan E. Thomas, Warwick Stewart, Stuart Miller

Sequential Net Acid Generation (NAG) accelerated oxidation testing using peroxide was carried out on single sulfide mineral samples. The calculation of the nett acid production potential (NAPP) assumes that all the sulfide is present as pyrite and that dissolution results in a 2:1 ratio of H+:SO42-. NAPP as kg H2SO4/t is calculated as 30.6 x wt.% S present. To test whether this calculation is valid a NAPP* value was defined in which instead of using the wt.% S present for the calculation the wt.% S dissolved is used. Stoichiometric analysis of the dissolution products of the sulfide minerals as they would occur at pH 7 indicates, that in all cases, the ratio of H+:SO42- of 2:1 is viable. The NAG to pH 7 and NAPP* closely coincided for pyrite, bornite, chalcocite and covellite. For the three Cu-containing minerals, the NAG to pH 4.5 value was 0 as is predicted on the basis of the speciation likely to be present at pH 4.5. Acid generation is due to hydroxylation of the dissolved Cu between pH 4.5 and 7.0. The NAG to pH 7 and NAPP* values for chalcopyrite, arsenopyrite and pyrrhotite were in reasonable agreement but were not for either sphalerite or galena. Zn is not completely hydroxylated at pH 7 as is assumed by the calculation. For galena, surface analysis identified polysulfide formation on of the leach residue polysulfide. The formation of polysulfide is an acid consuming reaction. Therefore under conditions of accelerated oxidation the NAPP value is a reasonable estimate of the possible acid production in all cases except for sphalerite and galena. However, under conditions of less intense oxidation, for instance in columns, waste rock and tailings dumps, the formation of polysulfides is likely to be more widespread thus reducing the correlation between NAPP and the maximum possible acid production.

Jan 1, 2004

By E. Buehler, E. Berry

HE magnetic properties of dilute palladium alloys are of fundamental interest.&apos;&apos;&apos; Neutron diffraction studies3 have indicated that a better understanding of the behavior of these alloys could be realized with the availability of high-purity single crystals of palladium. Crucible melts of 99.999 pct pure palladium were found inadequate for such research. In a successful effort to fill this need, floating zone refining of palladium was undertaken. In this note the results of the initial experiments are reported. Zoning was accomplished in an argon atmosphere using 450 kc rf generator for an energy source. Samples 5 to 6 mm in diam were suspended in a gastight quartz envelope which could be moved vertically through the rf coil. A nominal upward traverse rate of 1.5 mm per min was maintained during a pass. Close coupling was found to be essential for stable retention of the liquid in the zone. Single crystals averaging 3.5 cm in length were obtained. Laue photography showed them to be continuous single crystals without gross imperfections. Several criteria were used for evaluation of the purity of the zoned material: magnetic behavior, low-temperature specific heat and residual resistivity ratios. Table I shows the residual resistance ratios obtained for two samples, one subjected to a single pass, the other zoned four times. It is appilrent that palladium can be zone refined with the electrically active impurities being transported toward the tail end. A decrease in susceptibility for zone-melted specimens over any previously measured material from 1.5" to 80&apos;~ has been obserted by H. J. Williams and R. C. Sherwood4 substantiating the residual resistance data. The specific heat measurements are currently being made3 and will be published at some later date. Discussions with J. H. Wernick and S. C. Abrahams are acknowledged. We also wish to thank G. F. Brennert for the residual resistance measure ments.

Jan 1, 1962

By Andrew D. McCallum, Russell A. Heins

"Until the advent of intensive cyanidation, gold gravity concentrates were generally treated by tabling. The table concentrates were smelted while table middlings and tailings were recycled to the milling circuit for further grinding and subsequent leaching in the CIP/CIL circuit. Gold recovery on production tables is relatively low, often only 30 percent, and rarely above 60 percent. Significant factors in tabling performance are; mineralogy and the operator’s experience and ability. Units have been developed by Gekko Systems to treat both batch and continuous gold concentrates. Unit sizes are determined by leach kinetics and the required residence time of the concentrate in the unit.Gekko commenced the commercialisation of intensive leaching of gravity gold concentrates in 1997 with the first commercial prototype of the InLine Leach Reactor (ILR). Over 20 units are now installed worldwide with half that number on the African continent. South African mines, South Deeps (Placer Dome WAJV) and Target (AvGold) have both installed InLine Leach Reactors. Ashanti Goldfields have placed the ILR on their standard equipment list and have six operating units with a seventh on order. AngloGold installed one of the first ILR production units at Morila in Mali.Gekko Systems successfully installed an ILR1000 Batch unit at the Antapite Mine in Peru in December 2002. The unit was installed to treat gravity concentrates and to replace a shaking table. Following installation, gravity gold recovery increased from 15% to 40% of total gold. The unit was operational from start up and the first gravity batch treated achieved 98% gold recovery. The gravity concentrates also have a high silver content and 95% recoveries on silver were also achieved.Preliminary testwork identified that the concentrates required additional oxygen to achieve peak performance. As a result of optimisation work in the laboratory, leach kinetics in the ILR have been excellent with only 6 hours residence required to achieve maximum gold extraction."

Jan 1, 2003

By James Norman, E. W. Gieseke

Spodumene is a lithium-bearing pyroxene, and is an important source of lithium compounds. Because of its high alumina and lithia content, it might be a desirable constituent of glass batches. The use of spodumene in ceramics will undoubtedly increase, as it has been shown that a mixture of the proper proportions of this mineral with soda feldspar and potash feldspar has a much lower maturing temperature upon firing than has any one of the three components. The mineral spodumene seldom occurs as pure mineral, but ordinarily with feldspars, mica and quartz. All spodumene-bearing rocks tested contained these minerals as gangue. Small amounts of iron and manganese oxides also were present, usually as stains on the silicate grains. Mica associated with the spodumene carried a considerable amount of lithia. This was discovered in flotation tailings, which, although virtually free of spodumene grains when examined microscopically, showed 0.4 to 0.5 per cent Li²O on chemical analysis. The lithia content of micas picked from the North Carolina spodumene rock was variable. Some samples contained little lithia, others more than 3 per cent. In 1938, under the supervision of Oliver C. Ralston,S the Bureau of Mines, in cooperation with the Tennessee Mineral Products Corporation, undertook to study the beneficiation of North Carolina spodumene by froth flotation. The Bureau had previously published investigations on the beneficiation of spodumene.2,3The methods described in the second publication3 did not give good results with badly weathered spodumene rock, so that more thorough investigation of the subject was warranted. Study of Method of Flotation Separation Most of the work on concentration of spodumene was done with rock from near King&apos;s Mountain, North Carolina. Rock from two

Jan 1, 1942

To provide suitable backfill material for the cut and fill mining method being used to extract ore from the C.S.A. mine, flotation tailings are deslimed in single stage cyclones. The sand fraction is stored on the surface in unagitated storage bins before being pumped underground, while the slime portion is thickened and pumped to a residue dam. Design and operating details of the sand preparation and storage sections are given.The initial preparation of a stope for filling, consists of laying percolation and decantation drainage pipes on the sill floor. Preparation for fllling of subsequent lifts consists of rearing up the ventilation pipes at the ends of the stope, preparing the decantation system, and building a barricade or wall. The fill is carried to, and discharged into, the stope through 4 in. diameter pipes and filling of any section is carried out 24 hr/day normally without supervision. The fill is retieulated underground to the 1200 ft level through rubber lined pipe installed in the upcast shaft. Boreholes of 3 in. diameter drilled from the1200 ft level convey fill to the 1800 ft level. The mine drainage system is basically designed to handle the water associated with hydraulic filling. A system of primary and secondary sumps has been installed to handle the percolation and decantation drainage from stapes and to allow settling of fines before the water is fed to the main pump station.A programme of investigation into the properties of the emplaced fill is in progress. Results to date indicate that the fill as presently placed and drained, will not cause any problems in the mining of vertical orebodies by cut and fill methods for lifts in excess of 300 ft.

Jan 1, 1969

By W. E. Keck

THE flotative properties of the principal minerals in Michigan&apos;s potential iron ores have been investigated to develop methods of bene-ficiation for the ores. One of these minerals, magnetite, is of considerable importance as a source of iron. Study of its flotation was similar to that of hematite1, another iron mineral in these potential ores. The present research consisted essentially of: (1) a survey of the literature on mag-netite flotation, (2) the preparation of pure magnetite, (3) the develop-ment of laboratory procedure and (4) flotation experimentation. Literature an Magnetite Flotation.-For the purpose of this discussion, the results of previous work on the flotation of magnetite can be sum-marized as follows. The mineral has been floated with pine oil2, and it has also been separated from synthetic mixtures with silicates by the use of the same reagent2. Magnetite and apatite in iron-ore slimes have been separated by flotation of apatite with sodium palmitate3. These data were utilized in the present investigation. Preparation of Magnetite.-The pure mineral was prepared from the magnetic-separator concentrate of an iron ore (obtained from the Wither-bee Sherman Corporation, Port Henry, N. Y.). This concentrate was slowly comminuted with laboratory rolls and pulverizer to pass 65 mesh and was then tabled several times. Tabling yielded a relatively coarse magnetite concentrate, tailing and slimes. The two latter materials were rejected insofar as the present work is concerned, and treatment of the magnetite (table concentrate) was continued by separating it into -65 + 200 and -200-mesh sizes. Separation of the sizes was made by first dry screening and then wet screening. The -200-mesh material was rejected to eliminate possible introduction of error into flotation

Jan 1, 1937

By Angela Binder, Oliver Langefeld

"The future of mining will be characterized not only by the application of modern technology, but also by the harmonization of economic, environmental and social issues. These areas set major future challenges which are complex and demand extensive knowledge. As an example, mining of highly complex orebodies for the supply of often critical raw materials, needs to consider technically demanding and cost-intensive extraction issues. The amount of tailings, which need to be stored, increases with the amount of ore mined. Therefore, the negative impact on environment and society increases. Hence mining becomes expensive with regard to all three aspects: economy, environment and society. In view of a sustainable mining practice this challenge should be used as an opportunity. The positive impact should be maximized for present and future generations. The objective is to create and use the mining openings in an optimum way related to sustainability. The approach of Blue Mining, which focuses on energy and ergonomics in the field of Sustainable Development, enhances the closure planning by recommending subsequent usage of such openings for energy storage. The approach fosters among others the implementation of the 7th Goal for Sustainable Development defined by the United Nations with the assurance of access to affordable, reliable, sustainable and modern energy for all. The usage of underground storage increases the stability of solar and water power usage, which are otherwise unreliable. Blue Mining embeds these issues in the main planning effort long before groundbreaking. This approach involves experience from past and current projects. This paper introduces the concept of Blue Mining with respect to post-mining utilization of a mine for energy storage. Methods and perspectives are presented with examples covering best-practices and lessons-learned."

Jan 1, 2017

By Roshan B. Bhappu

Selenium is found most frequently as an accessory mineral in the ores of lead, copper, and nickel, and is recoverable as a byproduct in the treatment of many of the ores of these metals. The geographic distribution of the selenium industry closely follows that of electrolytic copper, with the United States and Canada producing approximately 75% of the total output of the non-communist world. This situation is problem number one for selenium-its dependence upon the electrolytic refining of copper- for this byproduct source is not sufficiently flexible to permit a normal supply-demand balance. Furthermore, selenium has become a strategic material in short supply. Thus, new sources are being sought by both government and private interests. Although considerable attention has been given to this effort during the last few years, hardly any research has been published concerning the recovery of small amounts of selenium present in low-grade deposits. In such ores the metal occurs as native selenium or as selenides of iron, copper, silver, lead, and bismuth. In recent years, some native selenium (in both the gray and red form) and selenides, especially iron selenide (ferroselite), reportedly have been found in the sandstones of the Morrison formation near Grants. New Mexico. Similar occurrences have been reported in the Hagan coal basin, in Sandoval County, New Mexico. Samples from New Mexico ores have contained from a trace amount to as high as 0.425% Se. Some of the samples from uranium mines in the Grants area represent mixed ore and mill feed fur uranium reduction plants. In such cases, the selenium usually is reported as an impurity and is lost in the tailings. At present, no attempt is made to recover this waste metal.

Jan 8, 1962

The methods employed in dressing &apos;the tin ore up to the required percentage of purity depend mainly on the type of ore crushed.These may be briefly divided into two distinct classes-viz., q, free: milling ore and a complex milling ore. In the former the ore is practically free from the common metallic sulphides, such as pyrites, mispickel, blende, galena, etc., and 1!&apos; clean concentrate of 70 per cent metallic tin can be directly obtained in one continuous act of concentration; in the latter, however, in order to get a good extraction, it is only advisable to primarily concentrate up to 30 to 40 per cent. tin oxide, the rest being the sulphides of the metals. This concentrate is then roasted, re-ground, and re-concentrated up to 70 per cent. metallic tin on a separate set of tables.In the complex milling ore the tin is intermixed very closely with the sulphides, so that it becomes necessary to collect all the mineral present in order to obtain clean tailings. Stamp mills are the most popular machines for the primary crushing in the district, but whether they are invariably the best for the purpose is rather an open question. No doubt for some of the very tough chloritic ores they are the most efficient, but for a brittle quartzose ore, such as the free milling proposition usually is, the writer thinks Oornish rolls would well hold their own, especially when the tin occurs coarse, as is so often the case with this class of ore. Of course, the great drawback to stamps is the excessive quantity of tin slimed and slime tin is one of the problems of tin-dressing-while rolls give...

Jan 1, 1907

By James Norman, E. W. Gieseke

Spodumene is a lithium-bearing pyroxene, and is an important source of lithium compounds. Because of its high alumina and lithia content, it might be a desirable constituent of glass batches. The use of spodumene in ceramics will undoubtedly increase, as it has been shown that a mixture of the proper proportions of this mineral with soda feldspar and potash feldspar has a much lower maturing temperature upon firing than has any one of the three components. The mineral spodumene seldom occurs as pure mineral, but ordinarily with feldspars, mica and quartz. All spodumene-bearing rocks tested contained these minerals as gangue. Small amounts of iron and manganese oxides also were present, usually as stains on the silicate grains. Mica associated with the spodumene carried a considerable amount of lithia. This was discovered in flotation tailings, which, although virtually free of spodumene grains when examined microscopically, showed 0.4 to 0.5 per cent Li²O on chemical analysis. The lithia content of micas picked from the North Carolina spodumene rock was variable. Some samples contained little lithia, others more than 3 per cent. In 1938, under the supervision of Oliver C. Ralston,S the Bureau of Mines, in cooperation with the Tennessee Mineral Products Corporation, undertook to study the beneficiation of North Carolina spodumene by froth flotation. The Bureau had previously published investigations on the beneficiation of spodumene.2,3The methods described in the second publication3 did not give good results with badly weathered spodumene rock, so that more thorough investigation of the subject was warranted. Study of Method of Flotation Separation Most of the work on concentration of spodumene was done with rock from near King&apos;s Mountain, North Carolina. Rock from two

Jan 1, 1942

By Foster Fraas

MOST commercial electrostatic separators utilize the electrical property of conductivity, but although based on the same principles, they are constructed in a variety of forms, a common one being the simple roll type. Some information obtained during an investigation of that type of separator, and which indirectly is applicable to other types, is presented here. NUMERICAL RELATIONSHIP In Fig. I material discharged from hopper 6 is fed onto grounded rotating roll 2. Electrode 3 is at a high electrical potential with respect to roll 2, and any conductive particle in contact with roll 2 therefore acquires an electrical charge of such polarity that, when present in the electrical field, the force on it is in the direction of electrode 3. A detailed description of the charging by conductance as utilized in electrostatic separators may be found in a previous publication.1 As a result of this force, the path of the projected particle is changed in increasing amounts in the direction toward region C as the magnitude of the charge is increased. With the dividing edge 4 the projected particles may be divided into two fractions -those in region C designated as "deflected" or " deflectant " and those in region B designated as "residue." When material is passed over the roll only once, a complete separation is seldom obtained, therefore most commercial separators contain several roll-separator units in [ ] series, and some practical machines use as many as 12. In this paper a "pass" means the passage of material over a single-roll unit. The procedure is to repass either residue B with a low potential on electrode 3 or deflectant C with a high potential on 3. Most electrostatic separations follow a flowsheet of roughing and cleaning either the concentrate or the tailing, on both. In a specific instance, a dry, heated mixture of wet cleaned chromite and garnet from an

Jan 1, 1942

To concentrate coarse mica particles using a dry beneficiation technique. Approach Concentrate coarse, II berated mica particles using a Bureau-designed system of crushers, screens, and a two-stage zigzag air classifier. How It Works Because mica has a flat plate-like crystalline structure, mica particles are significantly lighter than blocky gangue particles of the same size fraction. Thus an air classification technique can separate the flat, light mica particles from the heavier gangue particles. The ore, which Is first run through a standard jaw crusher, a roll crusher, and a hammer mill to liberate the mica, enters the rougher Zig-zag section through a rotating air lock. See photograph and diagram of a 2-stage air classifier. Airflow through the classifier can be varied according to the size of the particles being separated. The gangue material falls through the airstream of the rougher zigzag section and is discarded as tailings. The mica flakes are carried by the air-stream to the cyclone shown on the right side of the diagram, where they are collected. This rougher mica concentrate is fed to the cleaner zigzag section through another rotating air lock. The mica particles are again carried by the airstream but they are now collected In the cyclone on the left side. The cleaner concentrate leaves the left-side cyclone through a third rotating air lock and is rescreened to remove under-size material missed by the first screening. The final product of this pneumatic process is generally a high-grade mica concentrate. A generalized flow diagram for the pneumatic concentration method Is shown In the second diagram.

Jan 1, 1981

By P. Banerjee, P. Dash, S. Sriramoju, A. Suresh, R. Lingam, T. Ray

"One single property that influences the quality and market value of coal to the maximum extent is the ash content. The lower the coal ash higher is the energy utilization and potential for different applications. Even though Indian coal washeries aspire to produce coal with low ash, the intimate distribution pattern of ash bearing minerals in the coal matrix becomes the real bottleneck, as it brings down the clean coal yield to the impractical value. Because of this fact, most of the Indian washeries are operated to produce coal with 14-15% ash content at the yield of around 40%. In this context, with an objective to produce low ash coal at higher yield, a novel chemical beneficiation route has been explored to demineralize the high ash containing Indian coals. In this present work, the production of low ash clean coal from high ash Indian coals using chemical leaching process has been studied at pilot plant level. The leaching process parameters such as reaction temperature, reagent concentration, reaction time, coal-liquid ratio and agitator speed have been optimized for the flotation tailings sample from a captive washery of Tata Steel. The results obtained show that 67% demineralization could be achieved in a single stage of leaching process with a product yield of more than 65%. For further demineralization, multistage leaching was carried out and the results showed that 75-85% demineralization could be achieved with significant reduction in alumina to silica ratio. Additionally, the phosphorus content is also significantly reduced from 0.20 % to 0.022 %. Further, it is interesting to note that there is no increment of sodium content in the product coal after chemical treatment."

Jan 1, 2014

By X. J. Luo, F. Zhang

"Metallurgical slag (MS) such as steel slag, copper slag is a renewable resource and its compressive strength exceeds 200MPa in general. Because pure metal slug can easily be mixed into MS, complex recycle system is necessary in order to realize MS’s recycling. Meanwhile, there is high equipment failure rate in conventional crushing system. New crushing systems with inertial cone crusher could solve this problem very well. Recovery rate of MS tailings requires that crushing product can’t contain too much oversize product, so the essential equipment include two crushers and one sieve in the traditional crushing system. The new crushing system which only includes two crushers can meet the requirement and simplify the crush process. Investment of crushing equipment and infrastructure can be cut down. Operating and maintenance costs can be obviously reduced due to the simple process, which also could achieve high energy saving and excellent economic efficiency.INTRODUCTIONMetallurgical Slag (MS) such as steel slag, copper slag is a typical industrial solid waste and it threatens our environment’s safe. Metallurgical enterprises must take action to settle these wastes in order to protect our environment. Because pure metal slug can easily be mixed into MS, its uniaxial compressive strength (UCS) will exceed 200Mpa. If crushing station employs traditional crushing equipment, equipment failure will be easily caused because of these pure metal slugs. Coarse crushing equipment usually adapts jaw crusher in traditional Crushing technology and rod mill will be utilized to finish the secondary and fine crushing works. And the same time screening machinery should be used to ensure the suitable particle size (Figure 1)."

Jan 1, 2016