Search Documents

By J. E. Dutrizac

A mineralogical study of a weak acid leach residue from the Clarksville zinc plant of Savage Zinc Inc. was carried out. The study focused on Pb and Cd as these elements most significantly impact on the environmentally acceptable disposal of the residue. The residue consists of major amounts of bassanite, zinc ferrite and various Zn-Pb-Fe-Cd silicate species. Also present are lesser quantities of PbSO4, sphalerite, Fe2O3 quartz, Mn-Pb-Fe oxides, SrS04, (Pb,Sr)SO4 iron gel-silica gel, jarosite and Ti oxide. The principal Cd carriers are the zinc ferrite, which contains up to 9.00% Cd and likely accounts for -45% of the total Cd content of the residue, and the various silicate species which contain up to 6.97% Cd and account for about 45 % of the total Cd. The sphalerite is a minor Cd carrier containing an average of 0.35 % Cd and accounting for -5 % of the total Cd; the other carriers contribute only trace amounts to the total Cd content. The major Pb carriers are PbS04, Pb-bearing silicates and Mn-Pb-Fe oxides. Minor proportions of the total 1.09% Pb content of the residue are carried by SrS04 and (pb,Sr)S04' Trace Ph carriers include the iron gel-silica gel, Fe-Zn-AI oxide and bassanite. The residue after the toxicity characteristic leaching procedure (TCLP) is mineralogically very similar to the initial weak acid leach residue; the amounts of calcium sulphate are approximately the same in the two products. The principal Cd and Pb carriers are also the same as those noted in the initial residue, except that some dissolution and reprecipitation of Pb-Sr sulphate takes place. That the residue fails the TCLP test is likely a consequence of the superficial dissolution of Pb and Cd from species such as PbS04 or Zn-Pb-Fe-Cd silicate.

Jan 1, 1995

By P. S. Sundar

A laboratory method for the simulation of in-situ leaching of uranium was developed under contract to the Interior Department's Bureau of Mines. Simulation tests using sulfuric acid, ammonium bicarbonate and sodium carbonate as reagents and hydrogen peroxide as oxidant were carried out with representative ores from Texas and Wyoming. The tests not only yielded recovery rates of uranium and permeability changes, but also qualitative inferences on the chemical and physical phenomena which occur underground. Leaching with basic solutions was found to be kinetic constrained and with acid solutions, equilibrium constrained. The rapid permeability changes observed when leach solutions were introduced, were probably caused by gas blockages in the packing. Precipitation of calcite or gypsum and the reaction of clay to leach solutions had slow and gradual effect on the packing permeabilities.

Jan 1, 1978

By G. Wilson

"Satisfactory hydraulic performance of a centrifugal slurry pump is not the only design criterion. If abrasive wear exists the severity of any damage can be reduced and the life of the wearing parts prolonged by selecting the correct pump to suit the conditions of service. This paper is concerned with the design and construction of centrifugal pumps for handling abrasive solids. The wear phenomena due to the slurry being pumped and the materials used to combat abrasive, wear are outlined. The hydraulic design of the impeller and casing and their relationship to wear and the hydraulic radial and axial unbalance are discussed. The prediction of abrasive wear in pumps can not be precise, as many factors are involved - and this is the object of current research."

Jan 1, 1973

By S. Castro

The aim of the present paper is to review the current technologies for arsenic removal in the copper metallurgical industry, and to show the progress made with some promising emerging strategies, involving the pre-treatment of copper-arsenic concentrates by selective flotation or by alkaline leaching with Na2S-NaOH solutions. The advantages of alkaline leaching are the selective dissolution of arsenic and antimony, the high extraction yield, and the practically nil loss of copper, which remains in the clean copper concentrate as a CuS residue. Alkaline ?cured? ? a procedure similar to ?acid-cured? in conventional leaching ? improves arsenic extraction and reagent consumption, making this an interesting technology for the treatment of high As-Sb concentrates. In light of recent advances on the selective flotation of enargite and tennantite, the importance of redox conditions to control the flotation/depression of enargite-tennantite from copper sulfides has been well established. However, problems of selectivity must still be solved. Additionally, the limitation imposed in some cases by the need to recover the molybdenum by-product must be considered. The application of selective flotation to obtain a high-arsenic or ?dirty? concentrate and its sub-sequent treatment by the alkaline leaching process is suggested.

Jan 1, 2014

By William P. Stroud

Chemical alteration of the compressive strength of sandstone has been investigated by the U.S. Bureau of Mines (USBM). Successful development of this technology would offer an attractive alternative to the methods now used for stress control in mines. Sandstone cores were stressed to failure under uniaxial compression at two different strain rates. Specimens saturated with either distilled or tap water showed an average 14% reduction in stress at failure compared with those dried in vacuum. Samples saturated with dilute solutions of aluminum chloride, hydrochloric acid, and polyethylene oxide showed no statistically significant difference in failure stress compared with those saturated with water. By contrast, compressive strength of the cores was increased some 7% by saturation with the nonpolar solvent carbon tetrachloride. No correlation was found between zeta potential and compressive strength.

Jan 1, 2010

By A. T. Harris

Ground quartzite, known in the industry as amorphous silica, is produced from a quartzite deposit near Honey Brook, Pa., by George F. Pettinos, Inc., of Bala-Cynwyd, Pa. The quartzite is mined by the open pit method and processed in a mill at the mine. The operation regularly produces five standard grades of sand and one grade of crushed stone; however, the company accepts special orders and will produce material to meet the customer's specifications. Beneficiation (chiefly crushing and screening) is controlled by laboratory screen tests on samples taken during preparation of the sand. The chief uses of the sand are for foundry operations, furnace lining, concrete aggregate, and Other specialized uses. The quartzite in this deposit is of uniform composition and does not require control by chemical analysis. However, for special purposes, analysis will be furnished.

Jan 1, 1965

By N M. Player, R P. Varden, E Jones

"An effective geotechnical design provides an accurate and appropriate assessment, balanced with a mining company’s risk profile. Justifying the cost of slope assessment requires an understanding of the input sensitivities, and resultant risk, to achieve a slope of a required functionality. As a project progresses from Scoping to Feasibility, the geotechnical risk becomes better resolved through increased expenditure on drilling, testing, analysis and modelling as long as the input data is appropriately spatially distributed. Providing accurate and appropriate geotechnical assessments in the early stages provides confidence in all following stages, especially where initial analysis indicates difficult geotechnical conditions. It is also in the early stages of project definition that there is most opportunity to maximise the value of the deposit through investigations into optimal mining methods.This paper examines the advantages of geotechnical engineering input through a project study period. Early geotechnical involvement allows the Scoping and Pre-Feasibility Studies to be more effective. Operational risks can then be better understood and dealt within the Feasibility Study phase, also ensuring that the correct risks and management controls are put in place.With commodity price pressure and cost of resource recovery in a downturned industry, reducing the risk to cash flow, resource recovery and safety should be a primary goal for all mining companies. Reduced risk can be effectively achieved through geotechnical design of slopes to achieve a required performance as part of an integrated study to the Reserve definition and mine design.Citation:Varden, R P, Player, J R, Player, N M and Jones, E, 2016. Justifying Slope Design Risks and Costs, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 185–201 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By A. D. Fisher

This paper describes the future position of metallurgical coal, particularly as applied to Canadian reserves. Quality coking coal is declining in availability, but preheating practices may alleviate this situation to some extent. Two new processes are discussed in the paper - formed coke and direct reduction - and their coal specifications are outlined.

Jan 1, 1972

The Mateen deposit comprises two large spodumene-bearing pegmatite dikes that outcrop along the, side and crest of a hill overlooking 'Rill City in the southern Black Hills of South Dakota. The Bureau of Mines investigated the Mateen deposit as part of a comprehensive study of the lithium mineral-production possibilities in the Black Hills area. The work was undertaken during the second World War, when the demand for certain lithium salts and compounds exceeded the small productive capacity of the industry. During the course of the investigation, the Bureau of Mines took 61 large channel samples from surface trenches, 4 channel samples from a shaft, and 3 from the face of an open cut. In addition, 8 diamond core-drill holes were completed to investigate the attitude of one of the dikes at depth. Metallurgical tests were conducted by the Bureau of Mines to determine the feasibility of beneficiating spodumene-bearing ores from the Mateen dikes.

Jan 1, 1948

By J Fraser, M Scoble

Within the past decade, incidents of mining–community conflicts have grown dramatically and represent one aspect of a phenomenon known as social risk. Research published in 2014 indicates that a lack of social acceptance is now a leading and costly cause of delays for mining projects.The rise of social risk, complemented by the need to earn the trust of an increasing number of stakeholders so that mining projects can be developed effectively, is problematic for the industry. Conflicts are occurring in situations where companies are fully compliant with regulatory and legal requirements, despite initiatives by mining companies to earn social acceptance and despite the proliferation of tools to support corporate social responsibility. Intensifying the impact of social risk is the fact that it has increased during a time in the global mining sector when companies have had to grapple with declining commodity prices, increasing capital costs and debt levels and the challenges of mining lower-grade deposits.This paper will explore a hypothesis that in today’s interconnected society, social risk in the mining sector constitutes a legitimate business risk that must be managed strategically. The reality facing mining companies is that information, once considered confidential, now travels quickly on social networks and via a growing number of groups and individuals that have earned a legitimate right to be classified as stakeholders in projects that affect their communities. To be successful, it is suggested that companies will benefit from increasing internal collaboration and providing training to equip teams to mitigate social risk to mining projects and protect reputation capital. The paper is based upon PhD research being undertaken to assess the points of intersection between social risk and social responsibility during the construction stage of greenfield mining projects.CITATION:Fraser, J and Scoble, M, 2015. Mining–community conflicts – can the future mining sector transform social responsibility?, in Proceedings Third International Future Mining Conference, pp 159–168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By J. K. Whyatt

During the past 2 years, U.S. Bureau of Mines (USBM) researchers reviewed an in situ stress investigation conducted in 1977 at a test site on the 4250 level of the Lucky Friday Mine, Mullan, ID. Although the field measurements of over core strain were found to be useful, significant deficiencies were found in the stress field estimation procedure. The stress field estimate was then updated to incorporate recent progress in statistical capabilities and new understanding of stress concentration factors for doorstopper cells, as well as to correct an error in the original stress solution procedure. Simple models were used to examine the possibility that systematic variations in material properties and stress fields existed at the site. These models succeeded in reducing the sum of squared error somewhat, but fell short of completely describing stress variations throughout the test site. This overcore measurement will be supplemented by two other measurements described in the second and third reports of this series. Other observations of stress field characteristics are discussed in the fourth report The final report will also characterize the natural in situ stress field in the vicinity of the Lucky Friday Mine. This work was undertaken to support USBM research on mining method design and rock-burst control for deep mines.

Jan 1, 2010

By S Harris, A Bossilkov

The Kwinana (Western Australia) and Gladstone (Queensland) industrial areas are among the few dozens of heavy industrial areas globally that demonstrate significant levels of regional resource synergies. Such synergies are also referred to as æindustrial ecologyÆ or æindustrial symbiosisÆ. Fundamentally they involve the exchange of by-products or sharing of utilities between companies in close geographic proximity to achieve competitive advantage and environmental benefit. A concerted research effort is currently underway to foster greater realisation of regional resource synergies in minerals processing intensive regions, in Australia and internationally. This paper summarises current insights from the foundation research into engineering tools and technologies and enabling mechanisms for regional resource synergy developments. Regional resource synergy developments were reviewed for 16 international and two Australian regions. It was found that Kwinana and Gladstone compare favourably with the well-regarded international examples of regional synergy development. Given the fairly strong evidence that self-organisation is critical for regional synergy developments, an implementation model has been proposed that captures entry points for synergy developments at the level of platform (industry collaboration), process (developing synergy opportunities) and project (assessing and implementing specific synergies). It was also found that regional synergies have so far developed in the absence of specific methods for identification and screening of synergy opportunities. Moreover, very limited attention has been paid to the associated technological and engineering challenges. The current technical research effort therefore targets: the development of a toolset for the identification and development of potential synergy opportunities; and assessment of technology needs and opportunities for regional synergies involving water, energy and materials recovery and reuse.

Jan 1, 2006

By Frank J. Weibelt

In accordance with provisions of the Strategic Minerals Act of 1939, the Bureau of Mines surveyed the chromite occurrences in California. The Seiad Creek deposit afforded excellent opportunity for developing reserves that could be used by the nation in case of critical shortages of the mineral. Subsequently an exploration and development program was undertaken in April 1941, which was concluded in October of the same year. Work included road construction, diamond drilling, drifting and crosscutting, surface trenching, and sampling.

Jan 1, 1949

By D. E. Smith, M. K. Murthy

"The commercial potential of a silica-kaolin deposit that occurs on the banks of and close to the Missinaibi River in the District of Cochrane, Ontario, is under evaluation by Algocen Mines Limited. The geological features of the deposit, as well as its probable origin, are described. Mineralogical analysis of the deposit samples indicates that the principal minerals are quartz and kaolinite clay; it is estimated that about 20 per cent of the deposit is kaolin clay. The impurity minerals present are: a slightly magnetic Fe-Ti oxide mineral, goethite, muscovite mica, tour-maline, staurolite, anatase and zircon. Laboratory research studies are in progress to develop and evaluate suit-able methods for the separation of silica sand from kaolin. Results to date indicate that good-quality silica sand with an Fe,03 content in the range of 0.012 to 0.025 per cent can be produced. It appears that the clay portion can also be beneficiated to yield products meeting commercial requirements. It has been possible to beneficiate a portion of theetlay to obtain the particle size distribution now specified by industry. However, research is continuing to develop suitable separation and beneficiation methods which can produce kaolin clay meeting all the commercial requirements."

Jan 1, 1970

By J. F. Henderson

THIS paper relates to an area of more than 5,000 square miles in the Northwest Territories extending north from Great Slave lake and including-the Yellowknife, Beaulieu River and Gordon lake areas. Within the last three years much interest in the area has been created by the discovery of remarkably rich gold-bearing veins and the realization that thousands of square miles of unprospected ground are underlain by rocks like those in which the veins have been found. Probably there were more prospectors in this area in 1938 than in any other part of Canada. The area lies 650 miles north of Edmonton, and 425 miles north of the terminus of the Northern Alberta railway at Waterways, Alberta. The Athabaska and Slave rivers provide an excellent water route from Waterways to Great Slave lake for large oil and wood burning boats and barges which operate from the latter part of May to October. The only portage is around a 16-mile stretch of rapids on the Slave river between Fort Fitzgerald and Fort Smith. The town of Yellowknife, on the north side of Great Slave lake, has sprung into existence during the past year and is the centre for distribution of supplies for the Yellowknife-Beaulieu region. The Con-Rycon and Negus gold mines, which came into production in September, 1938, and February, 1939, respectively, lie about two miles south of the townsite. Excellent airplane service is available from Edmonton to Yellowknife and from Yellowknife to all parts of the area. The prospector and mining operator have come to rely almost entirely on the airplane for supplies and for the transportation of personnel, camp equipment, and canoes from Yellowknife to localities selected for intensive prospecting.

Jan 1, 1939

By J. K. Whyatt

Researchers at the U.S. Bureau of Mines have been exploring recent advances in the use of strain-softening constitutive laws that approximate shear fracturing. The purpose of these tests is to investigate shear-fracture-related rock bursts in hard-rock mines. The capabilities and remaining problems in the use of strain-softening laws in finite-element, distinct-element, and finite-difference methods are reviewed. Performance of the finite-difference implementation of strain softening is compared to classic experimental results and observations of rock mass behavior in the Coeur d'Alene Mining District of northern Idaho. The results show promise for developing methods to identify the general location and orientation of shear fractures and their sequence of occurrence, but such methods cannot be relied upon to quantify post-fracture loads or displacements accurately. Uncertainty over the amount of energy consumed by failing rock and the dependency of energy consumption on model mesh definition prevent direct application of the results to analyses of rock bursts.

Jan 1, 2010

By George P. Demopoulos

For more than 20 years the author had the privilege of working closely on a number of R&D projects with Lucy Rosato and her team at CEZinc. Several of these projects were driven from the sustainability agenda that Lucy Rosato championed as an innovation leader that supported research collaborations. Highlights from this highly rewarding collaboration are to be presented in this paper. In particular we will deal with the following works-topics: (a) iron control via solvent extraction as alternative to jarosite precipitation; (b) production of high-density gypsum by controlled neutralization of simulated zinc plant process/waste waters; (c) selenium removal from weak acid solutions; (d) electrolyte purification by cementation; and (e) manganese control by oxidative precipitation with SO2/O2.

Jan 1, 2015

By J. Philip Bromberg

The 1977 Clean Air Act Amendments will have a large effect on the coal-fired segment of the electric utility industry. Since electric power generation constitutes by far the largest single use for coal, this legislation has the potential to greatly affect future patterns of coal utilization in the U.S.A. The inability to depend exclusively upon low sulfur coal as an exclusive mode of compliance with New Source Performance Standards may greatly lessen projected demands for low sulfur coal by eastern utility boilers. The requirements of the legislation is discussed with particular reference to the needs of the electric generating industry, along with the technologies available for complying with the Act.

Jan 1, 1978

By J. D. T. Steyl

"This paper presents a phenomenological model of the rate of iron(III) precipitation in batch and continuous autoclaves at medium temperature operating conditions. The rate expressions are based on information obtained from the literature and experimentation at low and high pulp densities. Special allowance is made for the formation of surface nuclei, which appears to be promoted at a higher iron(III) precipitate surface area, especially in suspensions of lower terminal acidity. This leads to the formation of secondary particulates and provides the required link to simulate high pulp density leaching-precipitation systems, using low pulp density batch precipitation data. In particular, the model allows direct application of the simulation to the autoclave oxidation of iron-containing copper sulfide concentrates and provides a good estimation of the relative precipitation rate of hematite, the preferred product, compared to hydronium jarosite. Some interesting mechanistic understandings of iron(III) precipitation in autoclaves are further elucidated.INTRODUCTIONThe objective of this work is to describe the rate of iron(III) precipitation and the relative amounts of hematite compared to hydronium jarosite precipitation during batch and continuous chalcopyrite oxidation under medium temperature (MT) (~130 to 160ºC) autoclave conditions. Published information has not yet revealed sufficient mechanistic insights about this sparingly soluble salt system under these conditions. The rate expressions in this paper are based in part on current literature information, supplemented by qualitative experimental observation at low pulp density conditions, in particular the high-resolution backscatter electron (BSE) images and particle size distributions (PSDs) of the precipitates. A summary of this work and insights from the literature are presented first, after which the behaviour of iron(III) in high pulp density leaching systems is used to derive a phenomenological expression of the effect of existing iron(III) precipitate surface area on the precipitation rate. The overall regression encapsulates all the experimental results, i.e., those obtained in both batch and continuous autoclave configurations (Steyl, 2012a)."

Jan 1, 2012

By William P. Diamond

In this U.S. Bureau of Mines study, production trends have been analyzed for 82 gob gas ventholes on 7 longwall panels in the Lower Kittanning Coalbed, Pennsylvania. Cumulative production from individual holes was found to vary considerably, ranging from 0.03 x 106 to 10.1 x 106 m3. Peak production rates were generally about 0.03 x 106 to 0.06 x 106 m3/d, but rates over 0.10 x 106 m3/d were observed. The variability of gas production from individual holes can be attributed to' several factors, including completion practices and problems, the extent of fracture development in the strata above the extracted panel, water production, and location on the panel. Of particular significance is hole location. Holes on the ends of the panels, where overburden strata are in tension because of the support of the surrounding pillars, were generally the highest and longest producers. This observation led to the experimental placement of gob gas ventholes in the zone of tension along the margin of a panel, instead of in the traditional centerline location, which is in compression. Analysis of 7 months of gas production data indicates that the experimental near-margin holes produced 77 pct more gas than did centerline holes on the same panel.

Jan 1, 2010