Search Documents

By Robert Stefanko

The following tables contain the average, maximum and minimum power parameter levels for several mining machines. Power factor is listed only for defined transducer output regions. The reasons for the undefined areas are provided in the Instrumentation Chapter. Several maximum voltage drops are included, and are computed from the no load line-to-line voltage: Again, the drops are from measurements at the low side of the load center. The machines are: Continuous Miners; F6A Alpine 76AM Jeffrey (d-c) 8CM Joy 8CM (10CM) Joy 9CM-2AH Joy loam Joy CU-43-2H Joy 2 each CM26H Lee-Norse CM28E Lee-Norse Shuttle Cars; 18SC Joy 48S Torkar (a-c) 2 - 10SC Joys input to rectifier 2 - 16SC Joys input to rectifier

Jan 1, 1973

By Levent Ozdemir

A 6-ft. diameter laboratory tunnel, raise and shaft boring machine was designed and constructed to carry out research investigations to enhance the performance of mechanical rock excavation equipment. The machine is operated with a computer control system and features extensive instrumentation to monitor and record various test parameters, including tri-axial cutter forces, machine thrust, torque, rpm and penetration rate. An extensive laboratory testing Program has been conducted using this machine, demonstrating the feasibility of attaining high rates of penetration in various sedimentary geologies. Also, a large data base has been developed to serve as a basis for the improved design and performance of tunnel, raise and shaft boring equipment.

Jan 1, 1986

By Thomas L. Theis

The use of a suspended growth system of T. ferrooxidans attached in a film to individual particles of bentonite and operated as a sequencing batch reactor has been shown to be a practical way of oxidizing ferrous iron in acid mine drainage. This component followed by limestone neutralization is both a technically and economically feasible approach to the treatment of these wastewaters in comparison to existing and proposed methods. The advantages, in addition to less expense, are greater safety, acceptable treatment at a lower pH, lower solids buildup, less danger of overtreatment, and greater flexibility in operational characteristics. In this report data on the continuous bench scale operation of the system under a variety of conditions shows sustained levels of oxidation in excess of 9%. A cost analysis projects capital and operating costs of $80/1,000 m3 of wastewater.

Jan 1, 1982

By R. H. Hiltz

One of the major hazards in underground coal mining is fire. The inherent hazard of fire is exaggerated by the nature of coal mining restricted areas, the highly combustible nature of coal itself, and a potential for explosive concentrations or dust and gas in the air it becomes imperative therefore to make every effort to eliminate the causes of fires, while providing the most effective means possible to control and extinguish those fires which may occur it has been demonstrated by prior work that the problem of control increases in proportion to the time necessary to institute control procedures. There are several areas of underground coal mining with obvious fire potential. Some of these, like belt heads, have reliantly undergone improvements in standby fire control devices Others, although having fire suppression systems available to them, have not received as complete a systematic study of their problems. Face machinery, particularly those without a water supply, falls in this latter category.

Jan 1, 1973

By Eleanor Abshire

THIS PUBLICATION is the third to be prepared as a result of a cooperative project by the Bureau of Ships and the Bureau of Mines for accumulating literature published on zirconium and hafnium. The undertaking also resulted in the establishment of an information center on zirconium and hafnium at the Bureau of Mines station at Albany, Oreg., for the use of research organizations and others. The present bibliography consists of references (with abstracts) to pertinent literature on zirconium. The first publication in this series was Information Circular 7771, Bibliography of Zirconium, published in April 1957. It consists of 969 abstracted reports and 645 U.S. and foreign patents. The second publication, called a supplement to Information Circular 7771, is numbered Information Circular 7830 and consists of 844 abstracted reports and 62 U.S. and foreign patents. It was published in October 1958.

Jan 1, 1962

By Michael E. Meadows

The results of tests to determine the .regional applicability of four synthetic unit hydrograph models are presented. The SCS curvilinear (Haan), SCS single triangle, Williams and TVA double triangle unit hydrograph models were tested on 271 events from 38 USDA experimental watersheds in 14 physiographic provinces. Though inconclusive due to the limited number of events analyzed, the results indicated a regional tendency for each model, with the SCS curvilinear unit hydrograph method generally performing best overall. It outperformed the SCS single triangle by predicting better shape; they differed less than 2 percent in time of peak and peak rate predictions. The Williams model performed well at Oxford, Mississippi and Coshocton, Ohio, which suggests it may be applicable to surface mined lands within the Northern and Central Appalachian Plateau and Texas coal producing regions. The TVA model is applicable to the Appalachian Plateau, specifically the Cumberland Plateau. A second test using only the SCS curvilinear unit hydrograph on 11 small watersheds and 50 events was conducted to investigate the effect of the excesss rainfall pattern on simulation results. A Green and Ampt infiltration model was coupled with the SCS unit hydrograph model to determine if peak rate and timing errors noted in the regional test could be minimized with an alternate to the SCS curve number model for determining infiltration losses. The results confirm the curve number model is the better approach to determining the excess rainfall pattern for unit hydrograph simulation.

Jan 1, 1983

The applicability of borehole assaying techniques, both conventional and advanced, to orebody evaluation in the mining industry is reviewed and assessed, and the research, development, and demonstration programs necessary to apply the various logging techniques to mining are outlined. At present, the principal method of orebody evaluation in the mining industry is coring. However, coring is costly and time-consuming, and potentially great savings can be realized if all or part of d coring program is replaced by a borehole logging suite specialized to the needs of the particular mining industry. Using a set of 12 minerals, most of which are essential to the U. S. economy, an algorithm is presented for calculating the priority of developing suitable borehole assaying technology to replace all or part of the coring in each mineral industry, The priority is expressed in terms of dollars currently spent for that portion of present orebody evaluation techniques which may eventually be replaceable by in-situ assay techniques. The orebody assay requirements (grades, accuracies, etc.) of the 12 selected mineral industries, as determined from mining industry interviews and published literature, are compiled and represent performance criteria for borehole assaying instruments for the particular industry. Current logging techniques, applied chiefly in the petroleum industry, and advanced assay techniques which are or may be packageable for borehole use are evaluated to determine their performance characteristics. The performance characteristics of the various conventional and advanced techniques are then compared with the performance criteria in each of the 12 mineral industries in order to determine the potential benefit derivable from each technique. Finally, the benefit available from each technique, averaged over the 12 mineral industries, is compared with the cost of development of the technique, to determine the overall priority for investment in research to develop the technique for use in mining. The technology assessment and cost-benefit analysis shows neutron activation analysis in its various forms to have the highest priority for research and development as a borehole logging technique. Other techniques found to be promising include x-ray fluorescence, x-ray diffraction, photoluminescence (optical fluorescence), and infrared spectroscopy. Of the 12 industries considered in the study, those where the need for advanced borehole logging technology is greatest are uranium, copper, gold, and iron.

Jan 1, 1976

By Paul G. Swanson

This investigation was conducted to identify the principle causes of spoil instability problems in the Eastern Coal Province. The study was also conducted to develop a matrix to predict the strength and groundwater parameters necessary to conduct stability analyses on a proposed reclamation scheme. Suggestive methods to reduce spoil instability potential are also included. Numerous physical property, strength, compressibility, chemical and mineralogical tests were conducted on mine spoil samples obtained from 11 different surface mine sites. Site characteristics that influence the position of the post reclamation groundwater table were identified. Distinct regions within the Eastern Coal Province with high incidences of surface mine slides or high landslide susceptibility were identified. The application of the predictive matrices developed in this study is for surface mine sites mined and reclaimed in general accordance with the Surface Mine Reclamation Control Act of 1977. A review of current mining practices and the relative effect on spoil stability is included.

Jan 1, 1983

By Kenneth C. Ko

An engineering investigation was carried out on the technical and economic feasibility of implementing flexible liner/backpacking support systems In an advancing tailgate longwall mine. The system for a model mine consists of a circular tube constructed of liner plates and flyash backpacking. Flyash is pneumatically stowed into the tailgate. Small amounts of cement may be mixed to improve the support capability of the fill In difficult local ground conditions. Water is added inside the nozzle immediately prior to spraying. Results of theoretical analyses and a field test show that the designed system is technically feasible, can be cost-competitive, provides more stable ground conditions, and can Increase productivity and coal recovery, when compared with existing retreat longwall systems. In certain mine layouts, the new system can reduce the direct mining costs by a significant amount. The system would be particularly applicable to deeper coal beds with bad ground conditions.

Jan 1, 1980

By David R. Jessey

Water pollution problems associated with surface metal/nonmetal mines throughout the United States were assessed. Three major problems were identified: acid mine drainage (AMD), toxic concentrations of heavy metals and excessive sedimentation. Several factors affect the type and amount of pollutants generated at a mine site. Among these are hydrologic regime, geology, mineralogy, topography, climate, size of the mineralized area and mining method. Nine surface mines situated in distinctly different settings were visited and their pollution problems studied. These mines were located in Morenci, Arizona; Hayden, Arizona; Sauharita, Arizona; Cobalt, Idaho; Spruce Pine, North Carolina; Iron Mountain, California; Butte, Montana; Fernwood, Idaho; and DeLamar, Idaho-Oregon. A detailed evaluation of the pollution problems at the Morenci mine indicated that a diversion system and treatment pint would be the most effective means of abatement for the existing water quality problems. Based on the study of the Morenci mine and three other porphyry copper mines with differing problems a water management plan was conceived for a new source copper mine. A companion Appendix Volume containing detailed reports on the mine site visits is on file at the US Bureau of Mines Spokane Research Center.

Jan 1, 1981

By R. W. Welker

A technique was developed for sampling and analyzing airborne dusts in diesel-operated, underground, metal, and nonmetal mines. Samples were taken using personal respirable samplers, operated as area samplers, and an 11-stage cascade impactor. Real-time particle size distribution and concentration measurements were made with a quartz crystal micro-balance cascade impactor and a portable electrical aerosol analyzer. The materials characterized were minerals (by XRD), elements (by XRF), particle size distribution and concentration (gravimetrically), and organic constituents (by HPLC). The method was used to characterize dusts generated at the chute pulling operations on the main haulage level of an underground tungsten mine. Analysis showed that respirable dust concentration ranged from 0.8 to 2.3 mg/m3. It consisted of silica (3-7%); organic constituents from diesel exhaust (0.11-0.31 mg/m3 equivalent airborne concentration); and mineral dust (39-100%). The remainder was diesel exhaust particles. It was concluded that size selective sampling may be used to estimate the ratio of diesel exhaust to nondiesel dusts in the respirable fraction.

Jan 1, 1982

By William C. Hood

A leaching column technique that produces effluent similar in quality to coal mine drainage in the Eastern Interior Basin has been developed. The columns are charged with 1000 grams of crushed overburden and cycled through the leaching process once a week for twelve weeks. Inter-relationships among the important chemical constituents are very similar to those present in actual mine drainage waters, but the overall concentrations of ion are more dilute in the leachates. Multiplying the leachate concentrations by a factor of 4.5 gives values similar to mine waters. Available data suggests that each of the leaching cycles represents about three years of natural weathering, so that the leaching technique can predict the evolution of the mire drainage water over a time span of nearly 40 years. Use of the leaching technique with drill core samples should provide a method of approximating mine drainage quality in advance of mining and should be quite useful in identifying potentially toxic units in the overburden. However, the results should he considered to be a 'worst case' situation because the technique' does not consider the effects of reclamation.

Jan 1, 1984

By Rudolf E. Grauer

[ ]

Jan 1, 1981

By Fun-Den Wang

This report presents theoretical studies and experimental work dealing with the detection of dangerous roof and pillar conditions in underground mines through measure¬ment of temperature differences on the surface of the mine opening. The theoretical work is directed at modeling the circumstances where a loose slab of rock might be detected. The experimental work provides input data for the theoretical models. At the beginning of the project, little was known by the authors of the conditions that would permit detection of a loose slab of rock or coal by measuring the surface temperature differences. The U.S. Bureau of Mines had found that there were detectable surface temperature differences on the roofs and pillars of mines. The Bureau contracted with Colorado School of Mines to measure temperature profiles around mine openings in an effort to learn if the temperature differences they had detected were directly related to loose pieces of roof and pillar rock. The Bureau was principally interested in learning if loose rock could be found in coal mines by measurement of surface temperature differences with an infrared thermometer.

Jan 1, 1972

By Paul Meadows

This Bureau of Mines report presents operating practices and results of pressure maintenance and secondary recovery by water injection or by water injection supplemented by gas injection. Particular emphasis is placed on the results of water injection, which is the principal oil-recovery method employed in projects covered by this report. No attempt is made to study gas-injection projects or operations that are considered water-disposal projects. Also, this report does not include water-injection projects that have not been in operation long enough to evaluate results. Figure 1 is a map of north Louisiana showing the geographical locations of the projects included in this report. Most of the data used in this study were supplied by unit operators, operating companies, and the Louisiana Department of Conservation. Reservoir information and recovery data are generally those supplied by the operators, but include revisions where deemed necessary.

Jan 1, 1962

By M. K. McCarter

Previous investigations suggest the possibility of determining shear strength of geologic materials by measuring the force necessary to rupture the web between two closely-spaced, parallel holes using a borehole jack. Current research using finite element modeling and laboratory testing of intact rock indicates that web failure initiates by tensile fracturing induced by a complex stress field. Based on these results, a theoretical justification for relating web strength with shear strength appears unlikely for holes of equal diameter spaced two diameters apart. Empirical results, however, show a strong correlation between average web strength and average unconfined compressive strength for some rock materials under laboratory conditions. A good correlation also exists between residual web strength and the residual angle of friction under the same conditions. This research project involves the construction and field testing of a large borehole jack. The jack is designed to operate within a conventional 12-1/4 inch rotary blasthole common to open pit mining. The system is capable of exerting approximately 800,000 pounds on curved platen measuring roughly 4x24 inches. Field tests indicate that the system will operate in a mining environment, and preliminary results suggest the possibility of using the force-displacement data generated by the jack to rank the competency of material within a mine bench.

Jan 1, 1982

By C. A. Geffen

This report, sponsored by the U. S. Bureau of Mines, presents the results of an examination of the safety of the impactor shaft sinking system in comparison to conventional shaft sinking technology. Detailed study of the impactor system was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the impactor machine and its support systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates measures of both the frequency and the potential consequence of accidents. A safety evaluation of the com¬ponent operations of the impactor shaft sinking system was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that the impactor shaft sinking system is safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by an average of over 35 percent with use of the impactor shaft sinking system. Design change recommendations to further improve the safety of the impactor system include a revised fire suppression system, improved access to and from the operator cabs, reliable noise attenuation measures and improved communication systems. An operational safety manual was also developed for the impactor shaft sinking system.

Jan 1, 1982

By Robert L. Lagace

This report describes the results of a system study of the factors influencing mine rescue attempts based on the use of electromagnetic VF rescue transmitters by trapped miners and helicopterborne search receivers by mine rescue personnel. The findings cover four main task areas. The first - mine emergency/disaster considerations - concentrates on characterizing the events and key parameters of mine fires and explosions related to trapped miner location and rescue activities. The parameters include critical time periods, affected areas, survival times, response and rescue times, and survival rates. The second - hardware considerations - concentrates on characterizing the relevant properties of VF rescue transmitters, oxygen-type self-rescuers, VF search receivers, helicopter performance, and signal detectability and sensor sweepwidths for helicopterborne sensors. The third - search theory probabilistic model develops a method to identify the most important regions to be searched, and to allocate helicopter-based search effort so as to maximize the number of miners detected in time to be rescued. The fourth - sensitivity analyses and application of the search model - exercises the search model on representative mine emergency/disaster scenarios to assess the impact and effectiveness of helicopter-based searches. Conclusions and recommendations are presented, together with a set of search scenario planning guidelines.

Jan 1, 1982

By Andrew K. C. Wong

Hydraulic transport has been considered as one of the most economical methods in transferring granular materials over relatively long distances. In the natural world, it is used to transport basic material required for the support of life; in industry, it is a method widely adopted for handling materials. But the phenomena of hydraulic transport has not yet been thoroughly understood. As most of them are conditioned by a number of hydraulic and mechanical parameters, of which the basic relationships are not fully known, the traditional approach in relating these parameters to the energy requirement is purely empirical in nature. Empirical formulas, such as that proposed by Durand, (1) only give satisfactory results over a selected range of (particle size)/(pipe diameter) ratios and slurry concentration. When the case is more complicated or when new situations arise, the empirical formulas fail to give good predictory results. In fact, most of these formulas are based upon dimensional analysis, where the underlying physical interaction is not explicitly considered. Apart from the loosely related, non-dimensional groups incorporated in the formulas, there is practically no analytical means for modifying the formula so as to enable it to cope with more complex real physical situations. Although it seems quite remote that a complete rigorous solution to this highly complex problem could be generated in the near future, it is generally recognized (2, 3) that research in this area should be directed to more comprehensive studies of the obscure phenomena. In fact, there are a good number of very basic problems such as the effects of gradation and concentration of particles upon

Jan 1, 1972

By D. B. Lovett

The work described in this report was directed toward identifying and devising methods to minimize the previously observed variability between working level hour exposures and the alpha particle track densities resulting on Track Etch films exposed to mine atmospheres containing radon and radon daughters. The disequilibrium between radon and its daughters was shown to directly affect this Track Etch film calibration factor. The wide range of disequilibrium states possible in mine situations amply explains the variability in the previous tests. A file of published mine atmosphere composition data was compiled and was used, along with atmospheric compositions derived from several theoretical models ref the atmospheric behavior, to evaluate the variability of several dosimeter configurations and concepts. A nonlinear, iterative regression analyse; was formulated that successfully predicted working levels to within 8 to 10% from only the alpha particle activities (Rn, RA, and RaC') data such as are obtainable from Track Etch films over a wide range of disequrlibrium conditions. A model expressing atmospheric concentrations as a function of radon source strength, plate out rate factor, ventilation rate and the fractional re-entry by recoil of previously platted-out daughters was derived and used in the regression program in addition to preparing a set of reference tables and graphs showing the disequilibrium behavior of the atmosphere. Other factors that can affect the Track Etch Film response writ considered and shown to he less crutial than the disequilibrium state. The results of a series of exposures of a dosimeter concept fixture in the Denver Mining Research Center radon chamber air presented and discussed.

Jan 1, 1976