Search Documents

By Rolando Campos

Until 1970, the Caletones Smelter of CODELCO-CHILE, División El Teniente, operated under the conventional pyrometallurgical process used by most of copper smelters. The annual copper production varied around 165.000 tons. The failure in the commissioning of the "oxygen smelting" technology in Peirce- Smith converters (1970-1972), forced further introduction of transcendental changes in the Caletones smelter operating scheme. Implemented technological innovations were based on wide studies and research works performed by División El Teniente. This paper presents a summary of technological modifications introduced, their impact on production and energetic performances, and short and medium terms improvement plans.

Jan 1, 1993

By John P. Gooch

The solubility of 1,1,2,2-tetrabromoethane (TBE) in water was determined from 1.0° to 97.0° C. The solubility (S) of TBE in grams of solute per 100 grams water was correlated with [S = 1,920.55 [exp (40292L7 11, T2 10 T 737.577 + 9.923962 ] where T is in degrees Kelvin. A thermodynamic analysis conducted on a system consisting of a TBE phase and a water phase in equilibrium with a vapor phase led to the calculation of the activity coefficient, vapor-liquid equilibrium distribution coefficient, relative volatility, and heat of mixing for saturated solutions of TBE in water. Data required for these calculations were the solubility of TBE in water and the vapor pressures of TBE and water as a function of temperature.

Jan 1, 1972

By D. D. Munro

Finsch Mine is a Kimberlite diamond mine located at Lime Acres in the Northern Cape of South Africa. The mine was founded in 1961 and started surface-mining in 1964. Underground production commenced in 1990 using a Modified Blast Hole Open Stoping method for the mining of Blocks 1,2 and 3. Block 4 is currently being mined as a Block Cave. The process of identifying and optimizing a mining method to mine the Block 5 ore body started in 1991 and in 2006 Inclined Caving was identified as being a technically feasible method. This report aims to document the process employed in developing this method by the Block 5 Pre-Feasibility Team as well as discussing the technical challenges encountered during this process.

Jan 1, 2010

By F. P. Haver

The Bureau of Mines is developing a leach-electrolysis procedure to produce Special High Grade (SHG) zinc from sulfide concentrate without the generation of sulfur oxide gases. Chlorine-oxygen leaching of the concentrate yields zinc chloride (ZnCI2) which, after purification, is electrolyzed in a fused-salt cell to obtain molten zinc metal and chlorine gas for recycle. This paper describes a laboratory-scale investigation made to develop a procedure for electrowinning zinc metal from ZnC12. Zinc chloride by itself is not a suitable electrolyte because it fumes badly above its melting point and is a poor conductor of electricity. Other salts therefore must be added to prevent fuming and improve the conductivity. Optimum results were obtained with a KC1-LiCl-ZnCl2 bath at 500° C, using a current density of 5 amp/in2 and an electrode spacing of 0.5 inch. Under these conditions, SHG zinc was produced at a current efficiency of 94.3 pct and an energy requirement of 1.16 kwhr/lb. Fused-salt electrowinning eliminates the need to handle and melt cathodes and increases the production of metal per unit cell volume through the use of higher current densities than are possible with aqueous electrolysis.

Jan 1, 1976

By Reza M. Rahman

The froth phase plays an important role in the flotation and upgrading of the final concentrate. At present, the techniques that have been used in the mineral industry to measure the froth recovery have limitations. The aim of this paper is to investigate the performance of the froth in an industrial flotation cell. A unique device has been developed which is capable of decoupling the froth zone from the pulp zone. It consists of two concentric tubes. The inner tube acts as a dropback collection chamber or catcher. The particles that detach from the froth phase fall directly into the catcher and are collected as froth dropback. The froth recovery measurements were carried out in a rougher bank of a copper concentrator treating sulphide minerals. The dropback device is designed so that it can be immersed into a plant size flotation cell and plant froth recovery measurements can be taken at any given time. During the experiments, the bubbles laden with valuable mineral particles entered the device from the plant flotation cell, subsequently rising to form a froth layer at the top of the device. The particles that detached from the froth zone were collected in the dropback collection chamber whereas the concentrate sample was collected by a launder. By drying, sizing and chemical analysis of the concentrate and dropback samples, the froth recovery, was estimated on the basis of the valuable component. The effect of air rate on froth recovery was also investigated. Keywords: flotation, froth, dropback, froth recovery

Sep 1, 2012

By A. J. Hofmann, G. P. R. van der Merwe, J. E. W. Holm

"A new approach is proposed to perform relativistic comparisons between alternative operational risk management solutions by taking into account the impact of each operational activity on overall system performance. A specific case study, to which this new approach is applied, involves the deployment of safety systems in underground mining operations. Conflicting objectives to be satisfied are the minimization of risk to human lives and the minimization of production losses. As the focus in this case is primarily on the mitigation of risk, the approach that was applied is referred to as activity-based risk (ABR) analysis. Existing development process and risk management methods used in the South African mining environment were analysed by means of observations, a case study, technical documentation, and literature review. It was evident from this analysis that a discontinuity existed between the acquisition and operational phases in terms of the management of safety risk in the acquisition of electronic safety equipment when viewed from a full lifecycle perspective. This discontinuity could be addressed by defining a risk perspective in the system development phase by employing ABR in the preliminary design phase of a system’s engineering life-cycle. The focus of the ABR system development process is to find the functional definition and configuration of safety equipment that addresses both safety and productivity when taking into account human performance variability. In doing so, a balance between productivity and safety is found in a relativistic sense. IntroductionIn any system life-cycle, two major phases exist, namely system acquisition and operation (including maintenance). A distinction is made between acquisition and procurement, where acquisition includes system development and integration as specific engineering activities. In the development phase of a new system, conceptual design, preliminary design, and detail design phases follow in this order to define a complete system, after which the system is put into production and implemented in an operational environment—these activities chronologically define system acquisition in the context of this paper. It is not uncommon that differences exist between the risk management perspective during acquisition of a system and risk management perspective during operation, where nontechnical aspects are often ignored during acquisition, but are then encountered and found to be problematic during operation (Leveson, 2012). These differences also exist in the mining industry."

Jan 1, 2017

"Geometallurgy is a discipline that seeks to improve the sustainability of the extraction of metals and minerals by promoting the smarter use of non-renewable resources, better energy efficiency and greater use of renewable energy. To achieve these goals, development of innovative technologies and approaches are being developed along the entire commodity value chain, starting with exploration and extraction and extending to reuse and recycling. This paper discusses the geometallurgy of industrial minerals with special emphasis on kaolin, a versatile industrial mineral applied in ceramics, paper, paint, plastics, rubber, pharmaceuticals, cosmetics, ink, sealants, adhesives, sanitary ware, glass fibre, toothpaste, animal feed etc. Aspects of kaolin extraction in south-west UK are analysed from a geometallurgical perspective. While geometallurgy already features in kaolin extraction, its role can be significantly expanded by combining advanced in-pit characterisation and orebody modelling with integrated planning and control of the refining and calcination process. This paper highlights the importance of innovation in realising the full potential of geometallurgy.CITATION:Glass, H J, 2016. Geometallurgy – Driving Innovation in the Mining Value Chain, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 21–28 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

The goal of this presentation is to firstly, review mine effluent permits in a number of regulatory jurisdictions; and secondly, to develop a strategy for incorporating the regulatory requirements into the environmental assessment (EA) process for new mine proposals. The focus was on the province of British Columbia (BC) and their recent initiative on the One Project, One Process initiative. This task was approached by reviewing mine effluent permits for various regulatory jurisdictions and comparing them to BC mine effluent permits. This comparison revealed a variety of approaches for designing mine effluent permits, but there is a common scientific approach, which supports the conclusion that the permitting of mine site discharges can be designed based on a scientific approach. This approach is expected to: (a) achieve sound environmental protection, (b) demonstrate the application of Best Achievable Technology, (c) incorporate sound sustainability approaches, (d) incorporate regulatory objectives, and (e) create efficiencies for the regulator and mining industry. There is an essential precursor to developing a sciencebased effluent permit for which the proponent must provide: (1) the necessary technical assessment information to demonstrate the mine effluent permit application will result in an environmentally protective effluent discharge, to the satisfaction of the permitting agency; (2) the necessary level of detail for essential mitigation pollution control works to demonstrate how they will be operated to achieve the necessary treatment goals; (3) the necessary level of detail for non-treatment mitigation (passive treatment, or passive pollution control); and (4) the necessary level of detail to demonstrate how pollutants will be prevented from being mobilized (or being generated) from ore and waste materials, or, if the pollutant originates from an added milling reagent, how the reagent will be reduced. While (active) mitigation pollution control equipment is more definable in an effluent permit, non-treatment mitigation is more nebulous in terms of defining in a mine effluent permit; it is therefore recommended that appropriate management plans be developed for essential mitigation pollution control and non-treatment mitigation (passive treatment) and submitted with the proponent?s EA/effluent permit application packages. Major deficits in adequate active and passive pollution control will inevitably lead to regulatory impediments to developing a permit and allowing a mine to be developed, although EA processes strive to preclude major permit information gaps; the onus is on the proponent to provide complete information in this area. Hence the importance of EA processes ensuring that the major technical information requirements for effluent permit development are included in the EA phase. Recently, this aspect of the mine EA process has taken on a new role under the political efforts of One Project, One Review Process (Canadian) and One Project, One Process (in BC). These initiatives translate, in part, to ?synchronous permitting? (in BC): effluent permitting, for example, may be initiated shortly after the proponent submits the EA application to Ministry of Environment.

Aug 1, 2013

A digital computer program has been developed to mathematically simulate the effect of limited changes in feed rate on the grinding circuit of an operating mill. The data on which the program is based was supplied by the staff of the mill in question. Samples taken around the complete grinding circuit were analyzed for solids content and particle size distribution for two feed rates. Matrix models were used to represent the grinding units: rod mill and pebble mills. Parameters for these models were computed using a method developed by Mular(l). Classifier parameters were computed by the Powell search method(2) for the Plitt model (3) . The simulation program, which permits the computing of the size distributions in the circuit resulting from the changes in feed rate between the two measured values, assumes that a linear relationship exists between the corresponding parameter coefficients. The program uses an iteration method to bring the simulated grinding circuit to a steady-state material balance for any specified' feed rate between those measured. The program is, in addition, extremely fast and economic in computing time. The results show that the simulations are not everywhere consistent with practice. For example, higher feed rates on simulation predict finer products. These errors are shown to be attributable to anomalies in data gathering techniques. An improved sampling procedure for grinding-circuit data gathering is suggested for future simulations of this type. It is concluded that the

Jan 1, 1971

By T. W. Bingay

The production of both lead and zinc in Canada has steadily increased during recent years until today Canada ranks among the world's leading producers of both of these metals. The high prices which they have commanded have led to an energetic search for new deposits and also to an investigation of abandoned properties which, under the present conditions of better prices and more efficient methods of treatment, offer chances of commercial success. It is confidently expected that during the next few years success in both these lines of activity will further increase Canada's lead and zinc output, giving her a still higher ranking among the world's producers. In 1926, approximately 140,000 tons of metallic lead was produced from ores mined in Canada, and of this, 125,000 tons was refined in Canada at Tadanac, B.C. During the same year the production of metallic zinc from Canadian ores amounted to 68,000 tons, of which 62,000 tons was refined at Tadanac. History Of Lead and Zinc in Canada The production of lead in Canada is much older than that of zinc. The chief source has always been the interior of British Columbia. As earl y as the 'eighteen twenties', Indians and Hudson's Bay Company's trappers had discovered an outcrop of lead ore on the site of the present Blue Bell mine on the east shore of Kootenay lake, but it was not until1865 that active prospecting for lode deposits began. In the early nineties the activity of the silver-lead-zinc region of the Slocan reached its culmination and a steady production has been maintained down to the present time. Up to the end of 1924 the Slocan area produced over 38 million ounces of silver, nearly 300 million pounds of lead, and almost 122 million pounds of zinc.

Jan 1, 1927

By Daniel Hodouin, Claude Bazin

"This paper examines the economic advantages of tuning the operation of a differential Cu-Zn flotation circuit as a function of metal prices. Three operating strategies are considered in the analysis: 1) the operation of the circuit at planned copper and zinc concentrates grade with maximum recovery of both metals; 2) the operation of the Cu circuit at maximum copper smelter return per ton of ore and of the Zn circuit at a maximum zinc smelter return per ton of ore; and 3) the operation of the circuit at maximum copper and zinc smelter return per ton of ore. The second strategy tunes the copper circuit independently from the zinc circuit, while the third strategy tunes both circuits simultaneously IntroductionMetal prices play a very important role in the mineral industry (Malhotra and Dowling, 1991). In many cases, metal prices can be the basis for the GO/NO GO decision of a mining project (Malhotra and Dowling, 1991; Apostolides, 1983; Davis, 1996). This direct impact of metal prices on company revenues is highlighted in many annual reports. The 1995 Noranda Annual Report indicates that a variation of 10% of the copper price impacts its yearly revenues by $25,000,000. Some mine operators claim to mine stopes as a function of metal prices (Liimatainen, 1996; Hartman, 1992). This impact of metal prices is also recognized by mill operators that seek strategies to tune ore processing circuits to maximize revenues from the concentrate they sell to smelters (McKee, 1991; Barker et al., 1989; Hales and Ynchausti, 1994; Cipriano et al., 1995). In many cases the problem of tuning the operation of an ore processing circuit is complicated by the fact that the ore contains two or more valuable metals which have to be recovered into separate products. The Agnico-Eagle (Robitaille and Cousin, 1995) and Barrick East Malartic (Pelletier, 1996) Cu-Au mines are examples, as well as the Cu-Pb-Zn Brunswick mine (Shannon et al., 1993) or the Cu-Zn Louvicourt (Whiteway, 1995) and Selbaie (Wright, 1995) mines."

Jan 1, 2000

By P. Amelunxen

It is well-known that the particle breakage mode that occurs in a semi-autogenous mill is significantly different from that which occurs in a ball mill, enough so to warrant very different lab scale breakage tests and scale-up models. This phenomenon, at the plant scale, leads to changing process constraints depending on the particular properties of the ore. For example, hard or coarse ores might bottleneck the SAG/AG mill throughput, while the ball mills might constrain throughput when milling soft or fine ores. Because the power draw of a ball mill is fairly constant compared to that of a SAG/AG mill, periods of SAG/AG mill bottlenecks lead to increased ball mill circuit specific energy consumption and a finer grinding circuit product size, which together constitute a loss of efficiency of the overall process. Because HPGR circuit throughput is less sensitive to changes in ore hardness, this situation is less common or severe in those circuits. Furthermore, the ball mills are somewhat decoupled from the upstream crushing circuits through the use of surge bins, which also helps to mitigate this effect. As a result, ore hardness variability constitutes a significant cost penalty that should be applied to SAG mill/ball mill/pebble crusher SABC circuits when evaluating the relative economics of different grinding circuit configurations. Nevertheless, the issue is by-and-large ignored, because most current HPGR trade-off studies are based on averaged ore hardness parameters. This paper provides an estimate of the magnitude of this penalty for a typical operation by using Monte Carlo simulation methods and plant data from Freeport-McMoRan?s autogenous, semi-autogenous, and HPGR-based comminution circuits. A case study from an in-house 96K t/d sulphide project is presented to illustrate the concept. It was found that by including variability effects, the trade-off NPV of the HPGR circuit over that of the SAG mill circuit increases to $84 million from negative $33 million, effectively reversing the original decision of selecting a SAG mill circuit for the fixed hardness case.

Jan 1, 2012

By D. D. Rabb

Originally, the term solution mining applied to a dissolution, washing, or "brining" of soluble salts such as halite (common table salt), potash or trona. After the mid-sixties, however, the definition has been expanded to include heap and dump leaching, in-place (in situ) leaching, removal of oil from tar sands, extraction of sulfur from deep wells by the Frasch process and the recovery of metalliferous solutions from geothermal sources. Solution mining is also known as borehole, non-shaft, or chemical mining; the extraction of soluble mineral values from a variety of ores using appropriate solvents and chemicals. Solution mining frequently involves chemical changes; for example, copper usually goes into solution as copper sulfate, gold and silver as a cyanide compound, and uranium as a sulfate or uranyl tricarbonate. The valuable constituent is removed from the solid body of the ore by mass transfer to a aqueous solution.

Jan 1, 1986

By A. E. Moss

"IntroductionTHE WORLD-WIDE search for iron ore has been vastly accelerated during the past fifteen years .and Canada is playing a most prominent role in this prospecting boom. During this period, the search for .and development of iron ore deposits in Canada bas proven eminently successful and there is every indication that exploration will continue to be active for many years.This paper has been prepared primarily for the information of those who have bad little or no experience in iron ore exploration. For convenience, it is divided into three parts: ( 1) a brief discussion of the marketing of iron ores, with special reference to Canadian production; (2) a summary of the main features to be considered when prospecting for or evaluating a potential iron ore deposit; and (3) an outline of the methods and procedures used in the search for the direct-shipping iron ores in the Quebec•-Labrador iron ore field.The Iron Ore MarketDue to the tremendous tonnages of high-grade direct-shipping iron ore indicated in the iron ore fields of the Quebec-Labrador and Steep •Rock areas, it might be assumed that there would have been a sharp decline in iron ore prospecting in this country. On the contrary, the development of these two major fields, which must be classed among the world's greatest, has been responsible for much of the current activity. The search for high and medium grade magnetite deposits is being• conducted in many parts of the country and a number of these have reached the development stage. Production is being expanded from the known fields, such as Wabana in Newfoundland and Michipicoten in Ontario."

Jan 1, 1955

By Chester O. Ensign

The White Pine Mine is situated in the southwestern portion of the Keweenaw Peninsula of Upper Michigan approximately 6 miles south of Lake Superior (Fig. 1). It is east of the Porcupine Mountains in Ontonagon County. The ore deposit is about 70 miles southwest of the famous native copper deposits of the "Copper Country" lying northeast of Houghton. Geological conditions are different at every mine and create a special set of problems in dilution control. This paper is largely intended to describe the techniques applied in mine dilution control (grade control) at White Pine, and present results of the program. For necessary background information major geologic characteristics of the deposit, particularly those that exert control over the distribution of ore, are briefly discussed. Mining methods are described in considerable detail since applied grade control techniques are adapted to these.

Jan 1, 1964

By Griffith. F. E., Glei

"INTRODUCTION For many years protective grounding of electrical equipment has been advocated as a means of safeguarding equipment against damage and of minimizing shock hazards to persons. Several codes are in effect covering in considerable detail the items to be observed in obtaining effective grounding in and about industrial plants. Although the coal-mining industry does not have a comprehensive code of its own covering the grounding of electrical installations, a number of States and individual coal-mining companies have issued codes, standards, or rules that include certain requirements with reference to grounding. As early as 1916, 4/ and again more recently, 5/ the Bureau of Mines recommended grounding, particularly as a means of preventing shock to men working on or around electrical equipment.It is common knowledge among electrical engineers of public utility and mining companies that connecting a wire from the frame of a machine to a rod or pipe driven into the earth does not necessarily assure desired protection of surface equipment. In fact, it has often been found necessary to use several interconnected rods and to treat the surrounding earth with salt or other chemicals before the connection to earth would have sufficiently low resistance to give satisfactory results. Even these expedients have not produced the desired results in some localities. It has also been found that ground connections initially having a low resistance may attain high resistance during some seasons of the year. In spite of such difficulties with surface equipment, it has sometimes been assumed that a mining machine resting on the floor in a coal mine is grounded by virtue of its contact with that floor. It has also been assumed by persons endeavoring to comply with grounding requirements that a peg or rod driven into the mine floor would provide a sufficiently low-resistance contact with the earth to be satisfactory as an electrode for connecting the grounding wire from frames of equipment. That both assumptions may be wholly untrustworthy has been proved by the authors in actual tests with underground machinery."

Dec 1, 1943

By L C. Taylor

Both the U. S. Navy and the U. S. Army are interested in knowing more about the loading applied to vehicles which are unfortunate enough to encounter a detonation of a buried mine in the course of performing their normal duties. The Dynamic Effects Laboratory at the University of Maryland has been involved in small scale testing for ten years to assist the Navy and the Army in understanding the loads that are applied to personnel carriers when a buried explosive detonates beneath them. This paper describes results from small scale tests conducted to determine the loading mechanisms on target plates when subjected to loading due to the detonation of a buried mine in saturated sand, dry sand, and water. Transparent target plates were utilized in order to determine the loading process beneath a floor board on armored vehicles. Various charge sizes were scaled in the laboratory accordingly to a standardized full size threat encountered in the battlefield. Tests were conducted in saturated sand, dry sand, and water keeping the stand-off distance of the target and the depth of burial of the charge constant. In the case of water impacting a transparent PMMA plate the crack propagation was recorded and the crack velocity is determined. Additional tests were performed in saturated sand by varying the stand-off distance of the target but keeping the depth of burial of the charge constant. The small-scale test results could be scaled to full scale by using verified scaling laws.

Jan 1, 2016

By P. Hadzeriga

Ion exchange techniques have been growing fast and spectacularly in all phases of Science for the last two decades, but still its acceptance as a unit operation in Metallurgy is resisted. Mainly this is because ion exchange procedures are thought of as glamorous techniques by which only relatively expensive metals are to be recovered. Perhaps this concept comes from the early and basic marriage of uranium and other high price metals and ion exchange procedures. The general trend is that ion exchange technique requires equipment and materials which are too expensive to economically perform a chemical step whenever "cheap" commodities are produced. However, we are here presenting a means of utilization of waste hydrochloric acid by an ion exchange technique. We have studied this from the engineering and economic standpoint in a number of variations of the main procedure discussed here and we-conclude that under proper economic circumstances, the cost of the ion exchange material as well as the equipment and labor involved in the ion exchange section, is by no means unreasonable.

Jan 1, 1964

By B. Currie

Maintenance of quality electrowon copper requires an electrolyte which has suitable chemical and physical characteristics. The proper design and operation of the solvent extraction plant is essential to the quality of the electrolyte sent to electrowinning. An aspect that is not well appreciated is that the return electrolyte can have negative effects on the operation of the solvent extraction plant. Poor SX plant operation creates below optimum electrolyte conditions. High Eh in the return spent electrolyte can degrade the SX reagent with large decreases in copper transfer capacity and increases in internal entrainment. The synergistic interaction of the SX and EW plants needs a single-source design approach to address the interactions. The design elements in the SX and EW plants required to manage the electrolyte conditions are discussed.

Jan 1, 2014

By A. F. Jolly

In an effort to better predict the useful service life of friction rock stabilizer mine roof bolts in coal mine environments, the Bureau of Mines has evaluated the corrosion resistance of stabilizer steels in air-saturated and deaerated waters from seven Eastern and Midwestern underground coal mines. Accelerated electrochemical corrosion tests were used to estimate corrosion rates for the two high-strength, low-alloy (HSLA) steels used to fabricate Split Set stabilizers and for galvanized steel. Long-term static-immersion weight-loss tests were also conducted with the HSLA steels. Corrosion rates developed from the weight-loss tests (steady-state air dissolution) were roughly comparable to rates determined from electro-chemical testing in aerated waters. Although the highest rates occurred in waters with the highest chloride contents, rates in the other waters were low (<2.0 mpy) and exhibited little correlation to the widely varied chloride contents of the waters. The generally low corrosion rates are attributed in part to the tendency to deposit a protective CaC03 film, reflecting susceptibility to carbonate precipitation as indicated by positive Langelier (saturation) index values for the waters. With one exception, corrosion rates for the galvanized steel were (2.0 mpy. Rates with aerated waters were higher than those with deaerated waters. Pitting tendencies of the steels were also estimated.

Jan 1, 1987