Search Documents

By R. L. Stanton

"The present contribution is complementary with a preceding one on the field association of the conform-able ""pyritic"" deposits. It considers the more important features of their mineralogical constitution and their microtextures, re-examines the present interpretations of these, and of-fer-some alternative explanations. The term ""pyritic"" for these de-posits is m many cases a misnomer, as two quite distinct ore types are inuolve. One is a banded pyritic sphalerite-galena-chalcopyrite ore (for which the term '•pyritic"" is in-deed quite suitable), while the other is non-banded and is composed essentially of pyrrhotite and chalcopyrite. In addition to these constitutional differences, each is distinctive in general appearance and texture. The occurrence of two such consistent but clearly distinguishable ore types is attributed -rather than to difference in source material and pressure-temperature conditions of deposition -to the contribution of similar source material to dissimilarly oxygenated environments of sedimentation. Textures in the banded ores generally thought to be indicative of replacement or of high-temperature exsolution are explained by slow, law-temperature segregation in situ during compaction, folding, and regional metamorphism."

Jan 1, 1960

By Harold E. Rowen

The listed title of my talk to-day is "MODERN ON STRAND SINTER COOLING". Perhaps it should he ve been "COMPLETION OF SINTERING ON THE STRAND" as the two are synonymous. By the very nature of the DWIGHT-LLOYD SINTERING PROCESS partial cooling on the strand is always present, but not completion of sintering and cooling on the strand. I have mentioned the Dwight-Lloyd process just to be certain the type of sintering under discussion is fully identified because some of the basic mechanisms of sintering occur in various pyro-processing of fines lying in close quiescent contact, such as powdered metals practices, some types of pellet induration, firing of briquets, or other compacts, where the entire bed is brought to, and held at, the high reaction temperatures of sintering. Figure 1, The continuous sintering process as originally conceived consisted of intimately mixing carefully proportioned burdens, placing them in a comparatively thin, draft permeable layer, on a moving grate and igniting the surface while drawing sir through the bedded burden. The moving grate was advanced slowly as the line of burning fuel travelled from the surface to the bottom of the bed and no more fire zone could be seen.

Jan 1, 1973

By Joseph Chalmers

Stimulative methods of production, whereby the total recovery of oil from natural reservoirs is increased, have come into considerable prominence during the past 15 years. In many oil-producing areas properties considered ready for abandonment by ordinary producing methods have responded to some form of stimulation, and their economic lives have been extended. The stimulative method having widest application is the injection of air or gas into the reservoir formations through selected input wells and is commonly referred to as the "gas drive." As a result of the many successful "gas-drive" operations operators are depending more and more upon this method for increasing the ultimate recovery of oil from their properties. A number of factors influence the efficacy of different gases as propulsive agents in recovering oil from sands. Gases of high density and viscosity show a tendency toward a slightly higher efficiency than those of lower density and viscosity. The solubility of the gas in the oil also affects the efficiency of oil recovery. Not only does dissolved gas decrease the viscosity of the oil, but dissolved gas that expands from solution in the oil tends to increase the effectiveness of a "gas drive." Interfacial tension between the oil and the gas and its effect upon the recovery of oil by gas injection are factors of which little is known. Dr. A. G. Loomis expressed the opinion that interfacial tension probably plays a minor role in the recovery of oil, except under conditions that produce a gas-oil foam. In connection with the above physical properties that influence the action of a pressure medium, control of the injected volume of the pressure medium is perhaps the major factor. The rate of gas injection determines to a great extent the amount of slippage and the resulting efficiency of the operation. The importance of volume control is realized when one considers that frequently it is the only factor that is under complete control of the operator.

Jan 1, 1930

By Vaughan R. Voller

"The wide range of length and time scales found in solidification processes are outlined and discussed. Methods for Direct Microstructure Simulation (DMS) are introduced. Key features in sharp interface and phase field models are presented. Concepts in micro-macro solidification modeling are covered. Basic details of microstructure and segregation models are provided. A description of a recent segregation micro-macro model is presented in detail.IntroductionA solidification process involves the containment of a liquid region, which, due to cooling, transforms over time to form a fully solid product. The development of the solid microstructure and the segregation of solute components during this transformation are controlled by phenomena that occur across a wide range of length and time scales. A ""successful"" model of a given solidification process needs to account for these phenomena. Standard models of solidification employ a discrete grid of node points and associated volume elements in the special domain, with a discrete time step to track the transient changes of nodal values, describing the composition and microstructure. Through the use of such models significant progress has been made towards a complete understanding of solidification process and phenomena (see the conference proceedings in Refs [1-9]). As solidification models become more sophisticated, however, they all run into the problem of resolving the full range of disparate space and time scales.Two approaches can deal with this problem1. Direct Microstructure Simulation (DMS) where the grid size and time step are chosen to scale with the smallest length and time scales of the given problem.2. Micro-macro modeling where the grid size and time step scale with the macroscopic process scale and phenomena at smaller scales are accounted for via sub-grid modeling and volume averaging.Currently full DMS of solidification is beyond the reach of available computer power and the application and development of micro-macro models is an important and critical research area."

Jan 1, 2001

By Nathaniel S. Scott

Caland Ore Company Limited, a subsidiary of Inland Steel Company of Chicago, Illinois, leased an iron ore deposit from Steep Rock Iron Mines Limited on January 1, 1953.. This deposit lay underneath a lake and was covered with 161,000,000 cubic yards of Jake bottom material, mainly silt. Removal of this material was done on a contract dredging basis. This contract was divided into a plant phase and an operating phase. The plant phase consisted of supplying two cutter-type suction dredges, each with two booster pumps in the discharge lines. All six pumps were centrifugal, had 36" discharges and were powered by 10,000 horsepower electric motors. Peak demand was 59,157 kilowatts. One hundred and forty miles of steel tower line were built to bring power to the site. The balance of the plant consisted of tugs, 12 miles of discharge line, varying from 36" diameter to 42" diameter and attendant land-based equipment. A number of interesting dams were constructed

Jan 1, 1961

By George Innes

The soda ash business in the United States has undergone a sweeping technological change in ihe last 20 years. In a world where synthetics are continuzlly replacing natural products, here we have exactly the opposite, a syntheric chemical being replaced by a natural product. This change is nearly complete in the U.S. and is beginning to take place in Europe and other parts of the world.

Jan 1, 1980

By T Baumgartl, D Mulligan, R Haymont

Mining at the Mt Leyshon Gold Mine in semi-arid north Queensland stopped in 2002. Newmont Australia has recently initiated a thorough post-closure water management study of the site by revisiting the existing information and conducting new water-related investigations. The focus of this paper, which is the first publication on post-closure environmental management of the site, is an overview of the site water quality in view of the sources and spatial distribution of polluted mine water, and also the performance of cover systems in controlling water flux though mine wastes. Since the mine closed the rehabilitation of waste rock dumps and tailings dams have significantly improved water quality in the surface receiving waters. However, the Scats Stockpile, the Heap Leach and Old Plant areas, which can potentially produce acidic waters, enriched with heavy metals and arsenic, are the top management priority. Modelling of the potential transport of contaminants in groundwater needs further investigations. A detailed examination of the waters in seepage sumps showed high concentrations of manganese, cobalt, nickel and selenium, which were previously overlooked. The study also showed distinctive chemical signatures for waters at different locations: the waters draining from scats, supergene materials and waste rocks have distinctly lower pH and higher concentrations of dissolved iron, sulfate, heavy metals, Mg, Mn, U, Se and As. While, the tailings sumps are more alkaline, and are enriched in Na and Cl. The southern tailing sump is characteristically As rich. The waters draining from the supergene materials have higher Cu concentrations. Assessment of the cover monitoring systems showed that although covers pass the design criteria, automated recording of data may ignore any failure of the monitoring system. Recalibration of the moisture sensors not only showed realistic moisture values compared to rainfall data but also showed that the permanently installed system records values that are higher than those of the mobile system. Event-driven recording of data overlooks infiltration events. Besides, with a higher time resolution (daily measurements) the breakthroughs could be clearly detected. Modelling of the water balance in covers is underway and an example is given here. Newmont is currently reviewing water management options and is willing to share the lessons learned.

Jan 1, 2006

By T. L. Joseph

The size and accessibility of the Minnesota manganiferous iron ore deposits make them attractive as a potential source of erromanganese, which is essential in the production of steel. For several years the Bureau of Mines has been conducting experiments to determine the feasibility of producing ferromanganese from these ores by a three-step process which involves (1) the smelting of the ores in the blast furnaoe to produce a high-phosphorus spiegel; (2) the treatment of the spiegel produced from step 1 in an electric or open-hearth furnace to separate the manganese from the phosphorus and the iron; and 3) the smelting of the high-manganese slag from step 2 to produce forromanganese. The details of the first two steps of the process and the results of tests with the experimental furnaces Lave been given in previous reports.5 The m$ or part of the experimental work on the second step has been conducted in a half-ton open-hearth furnace. Some preliminary tests showed, however, that the electric furnace has some distinct advantages over the open hearth for producing, from high-phosphorus spiegel, a slag containing from 45 to 55 per cent manganese and phosphorus and iron in amounts required for ferro-grade ore. The electric furnace tests described in this paper were made to get more information as to the possibilities of the electric furnace in connection with this problem and to study the fluxing effect of alumina on high-manganese slags. Herty, Conley, and Royer have reported' results of laboratory tests which showed that slags containing from 60 to 75 per cent MnO, from 8 to 10 per cent S102, and small amounts of CaO MgO, and FeO, were sufficiently fluid at 1,450° to 1,550° C. to pour readily if 12 to 14 per cent alumina was present. With a normal A1203 content resulting from the A1203 in the

Jan 1, 1931

By T. T. Campbell

Studies were conducted by the Bureau of Mines to develop a process for preparing thorium-magnesium master alloys or pure thorium metal by magnesium reduction of thorium tetrachloride in a semicontinuous reactor. Thorium tetrachloride was prepared in a fluidized-bed reactor by chlorination of thorium oxide or thorium oxalate. Conditions were established for producing a suitable thorium oxide feed for a fluidized-bed reactor. Thorium tetra-chloride was purified by vacuum sublimation and subsequently reduced by magnesium in a semicontinuous reactor to form thorium-magnesium alloys. Relatively pure thorium was produced by removing magnesium from the alloys by vacuum sublimation. Close to 100 percent of the thorium fed into the reactor was recovered either as metal (~93 percent) or as thorium oxide (~7 percent). The oxide can be recycled directly into the process.

Jan 1, 1971

By J. Markussen

The Falconbridge Matte Leach Plant was based on leaching Ni-Cu matte with strong hydrochloric acid in rubber lined equipment. It operated from 1968 to 1983 as a precursor to Nikkelverk's present C12 Leach. The process comprised two S.X. systems. NiC12.4H20 crystallization, crystal drying, NiC12.H20 pyrohydrolysis and HC1 gas recovery. The naphtha fired fluid bed pyrohydrolyzer produced granular NiO, subsequently reduced with H2 to granular nickel for sale. The development and operation of the pyrohydrolyzer are described

Jan 1, 1991

By Herbert H. Kellogg

A model of the ISF is described. which reproduces with accuracy the "normal" operation of three industrial furnaces. The model, written in Fortran, is based on detailed heat and material balances, and the concept that the ascending gases reach equilibrium with zinc oxide and with the water-gas shift reaction. "Solution loss" of carbon in the lower shaft, and partial reoxidation of zinc vapor in the upper shaft are also essential features. For prediction of furnace behavior under altered operating conditions (blast rate, temperature, moisture content, oxygen enrichment, or injection of oil or coal through the tuyeres) the model modifies the heat loss, temperature of slag and bullion, amount of reoxidation in the upper shaft and the condenser efficiency to reflect the altered operating parameters. Model predictions for such operating conditions are in reasonable agreement with plant experience.

Jan 1, 1990

By P. D. Kovscek

The Bureau of Mines has tested a low-thrust water-jet-assisted rotary drill. This work was performed to evaluate the performance of a water-jet-assisted drill operated at thrust levels typical of a handheld manual-thrust operation. Prior work by the Bureau had indicated that using water-jet assist with high-thrust drilling applications would increase drilling rate. Small-diameter holes were drilled in five different types of rock. Thrust and water pressure were varied as the drill rate was monitored. The test results indicate that drilling rates increase with increasing water pressure and thrust. The water jet has more effect on reducing the specific energy when drilling in the harder rocks than in softer rocks. Variation in drill rate for a given rock sample is attributable primarily to the material heterogeneity within the sample. One rock type (Greenwich sandstone) could not be drilled efficiently with the water-jet-assisted drill.

Jan 1, 1988

By Jr. Sillers

This is the third report of investigations dealing with the application of electrolytic manganese to steel-foundry practice and the seventh in a series of reports dealing with tests to establish the technological acceptability of electrolytic manganese in the iron and steel industries. The work was carried out by Metallurgical Division of the Bureau of Mines as part of an extensive program for the development and utilization of domestic ores. The electrolytic manganese used in the tests was produced by the Bureau at its Boulder, City, Nev., pilot plant by the process developed by the Bureau of Mines.

Jan 1, 1949

By M. Sears, K. Mohamed, J. Addis, J. Wickline, G. Rashed

To better understand the load shedding and the stress transfer on coal pillars due to room-and- pillar retreat mining in deep cover panels, researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted a monitoring field study. Two sites, at overburden depths of 1,000 ft (304.8 m) and 1,500 ft (457.3 m), were selected in a room-and-pillar mine operating in Southern West Virginia. The deformation and stress changes in the roof and two adjacent pillars at each site were monitored during the retreat mining process. The monitoring results and field observations were used to calibrate large-scale FLAC3D models for each site. The calibrated models were used to assess different sizes of roof bolts installed in deep cover areas. INTRODUCTION Deep cover room-and-pillar retreat mining is an important emerging issue that will intensify in the future as shallower reserves are depleted (Mark, 2009; Chase et al., 2002). During pillar retreat mining, the likelihood of local and/or global instabilities increases due to elevated stress levels near the pillar line because of the abutment loading. In the last decade, approximately 31% of the room-and-pillar mining groundfall fatalities in the United States occurred during pillar retreat mining. Between 2013 and 2017, this proportion increased to 55%, of which 50% of these fatalities were due to falls of roof and rib that occurred during pillar recovery (MSHA, 2018). One interesting piece of information about pillar recovery fatalities was that the victim was nearly always under bolted roof. Sheared and broken #5 (5/8-in), fully grouted rebar bolt failure contributed to three of four fatal roof fall incidents that have occurred in deep cover retreat mines (NIOSH, 2010). This claim raised the following question at the study mine: Is it safe to use a 4-ft long #5 (5/8-in) rebar bolt grade 60 at a depth of cover more than 1,000 ft (304.8 m)? There was some concern about shear failure of the #5 (5/8-in) rebar bolt at a depth of cover over 1,000 ft (304.8 m). To answer the question and to reduce accidents and fatalities caused by ground falls due to room-and-pillar retreat mining in deep cover panels, the National Institute for Occupational Safety and Health (NIOSH) monitored the roof and rib deformation and the change in vertical pressure within two adjacent pillars during pillar recovery. The study was conducted at two deep cover sites in a room-and-pillar mine located in Southern West Virginia that operates in the Lower War Eagle (LWE) seam. The monitored sites were selected at 1,000 ft (304.8 m) and 1,500 ft (457.3 m) depths of cover. In this paper, site-1 represents the monitored site at 1,000 ft (304.8 m) of cover, while site-2 represents the monitored site at 1,500 ft (457.3 m) of cover. For this study, large-scale FLAC3D numerical models were calibrated based on both field observations and instrumentation results. The calibrated models were then used to compare the ground response and the induced stresses of two pillars at instrumented sites 1 and 2. The maximum lateral displacement (roof shift) obtained from the calibrated large-scale FLAC3D models was applied to a small-scale FLAC3D bolted models, the safety factor for axial stresses of the simulated roof bolts was calculated at the deep cover sites.

Jan 1, 2019

By H. P. Greenwald

[For sarno years past the Safety in Minbr. Resaarch J30ard of Great Bri tr-dn ha:1 been making ar.. intensive Gearch for, traterials that \.'ould be 1!\ore ef-ficient than rock dust and th t 'could l1eplace it Jholly or in El:}rt as a muans of prevEll'ltine the propa 'tion' of 'c63.1~dust exnlosions in. mines21 In the course of this \o.'ork several rock c.ur--ts md numerous inorganic compounds I,/ere tested. The result w place incombus.ti ble substFlnces in two main groups~ (1) r.:ho se who sa effect' in suppre aeina Jlihe cor.lbustion of coal dUDt i 0 pro-]

Jan 1, 1940

By Mingchun Lu, Yunjin Yan

"This paper describes a new type of bell-less top installed on two relined blast furnaces at Tianjin Iron Works and another new-built at Echeng Steel Works in China. A compact installation was presented for existing furnace top innovation with the least reformation of existing top structure. A water cooling and sealing gearbox used for driving the chute discards completely the traditional idea about necessity of continuous supply of cooling gas for the gearbox. A multiring spreader and its dozens of selectable charging patterns enables an operator to achieve optimal burden distribution easily under the condition of a minimum investment of control equipment. Some useful conclusions have been made through a small-size model and a full-scale model tests. The excellent characteristics and the superiority of the new top have been fully proved at both works.IntroductionIt is known that there are some advantages with the bell-less top of a blast furnace: suitable for furnace to operate at high top pressure, capable of realizing optimal burden distribution, less investment and maintenance costs, etc. But why do most of blast furnaces in the world still remain using conventional bell top. One of the concerns is that current bell-less tops still have some shortcomings:1) The height of a current bell-less top might be lower than three or four-bell top or two-bell plus valve seal top, but still much higher than an ordinary two-bell top.2) The gearbox for driving the rotating chute is positioned onto the lip of the furnace. It is subject to attack by crude hot bf gas. Continuously pumping cooling gas (pressurized nitrogen or clean bf gas) into the gearbox is indispensable to withstand such a harsh working environment. Therefore, a plant furnished with blower8 and its ancillaries has to be built, It involves a large sum of investment and much expense in its annual running costs.3) Although the current bell-less charging device as a means of controlling burden distribution possesses a wide range of freedom, it is difficult to realize optimal burden distribution. There are some large blast furnaces realized better burden distribution, but sophisticated control means is indispensable so that the investment of control means is much higher."

Jan 1, 2000

By R. Froidevaux

Geostatistical estimation techniques were customized to enable forecast of production figures at the Silver Bell uranium mine (Uravan District). Surface drill hole data were used to provide a block model of kriged estimators of average uranium grades. The recoverable figures, such as ore-waste ratio and ore grade, are then deduced from regressive curves previously obtained from underground information and production data. Cross-validations of the entire model were performed and were found positive.

Jan 1, 1981

By L. Giraldo, S. Cotten

"INTRODUCTION The vision for a “Mine Escape Vehicle” (MEV) is to provide capabilities to better enable underground travel to allow miners to escape to safety in the event of a major mine emergency such as a fire or explosion. Enhanced transportation and survival capability such as a MEV may have minimized or eliminated the loss of life associated with several of the mine disasters that occurred in 2006, which together resulted in the deaths of 19 miners. Although the most desirable response in an emergency is for the miners exit the mine, if escape proved to be impossible, the miners could use the vehicle to proceed to an underground point of refuge to await rescue. Under a NIOSH contract issued in April 2008, Raytheon developed a conceptual vehicle design including (1) the capacity to provide life support functions for a number of miners, (2) operate in a reduced oxygen atmosphere with little or no visibility, and (3) travel at speeds faster than miners could walk out of the mine. The proposed MEV concept envisioned modification of a personnel carrier (a.k.a. a “mantrip”) that would be used every day during normal mine operations, not a specialized vehicle reserved only for or dedicated solely to escape. The MEV concept also included escape aids that are detachable from the vehicle in the event that the vehicle must be abandoned on the way out of the mine and the dismounted miners had to proceed on foot. To advance MEV development, NIOSH awarded a second contract in 2010 to Raytheon to build, test, and evaluate the performance of a proof-of-concept MEV that culminated in a 7-month performance evaluation of vehicle in an Eastern Kentucky coal mine (Figure 1). User feedback and lessons learned from the proof-of-concept vehicle evaluation provided support for the general MEV approach, guidance related to the practicality of MEV capabilities, and indication of specific technology shortcomings for this application."

Jan 1, 2015

By K. L. Lamb

At the Sierrita mine, 40 km (25 miles) south of Tucson, Arizona, Duval Corporation is rapidly gaining operating experience with its new Portable Crushing and Conveying System, (PCCS). As of November 23, 1983, over 4.5 million tons (5.0 million st) of ore have passed through the system. Mining cost per ton for the months of July, August and September was 83% below the average for the first five months of 1983. Although all the cost reductions experienced cannot be attributed to the Portable Crusher, it was a major contributing factor. The Sierrita ore deposit has several natural topographic and geologic conditions which are not favorable to mining. It is not a sidehill deposit and therefore no low-level exit points exist to facilitate truck haulage. The ore is very hard. Quartz diorite, hardest of the three major rock types, averages 172-207 MPa (25-30 000 psi) unconfined compressive strength and may run as high as 345 MPa (50 000 psi). Blasting in this rock produces oversize material which runs approximately 20% 51 centimeters (20 inches). The ore is low grade, averaging slightly better than .30% contained copper and .035% contained molybdenum, with small amounts of silver. These conditions, plus high design production tonnages, make the Portable Crushing and Conveying System (PCCS) practical for Sierrita. Without crushing and conveying, truck haulage would be prohibitively expensive. A typical, October, 1983, ore haul from the bottom of the pit would involve a vertical lift of 260 meters (850 ft) and a horizontal distance of 3 860 meters (12 200 ft) were not in-pit crushing and conveying available. The corresponding cycle time would be nearly 32 minutes.

Jan 1, 1984

By Susan Brink

The U.S. Bureau of Mines is investigating the potential of in situ leach mining a variety of Cu, Mn, and Au-Ag ores. Geologic characterization of ore samples from laboratory leaching experiments is conducted both prior to and after leaching to assess the effects of leaching on the chemistry, mineralogy, and texture of the rocks. The identification and chemical compositions of ore, gangue, and reaction products are determined by a combination of techniques such as reflected and transmitted light microscopy, X-ray diffraction, electron diffraction, electron microprobe analysis, and backscattered electron imaging with scanning electron microscopy. The distribution of the desired metal in various mineral phases can be illustrated using elemental X-ray maps. The potential of reactive gangue minerals to rob Cu from leach solutions is investigated with the aid of transmission electron microscopy. Porosity and permeability are measured to determine how effectively the host rock can transmit leach solution. Textural relationships between ore, gangue, secondary reaction products, and fluid channelways are determined by petrographic examination and are documented by optical photomicrographs and secondary electron imaging. Representative sample selection is described, and several epoxy impregnation and sample mounting techniques are discussed.

Jan 1, 1991