Search Documents

By E. J. Gleim

In April 1932, the Bureau of Mines published Information Circular 6595, entitled "Data in Reference to Installation of Cables in Shafts and Boreholes", in which were described methods followed in various sections of the United States when electrical circuits are taken into mines by means of cables suspended in shafts and boreholes. In view of the present tendency to extend high-tension cables along entries and passageways from the bottom of the shaft, borehole, or other point of entrance to coal mines rather than over the surface, it is deemed that the various methods of installing such cables deserve careful consideration, particularly in mines in which gas and coal dust contribute to explosion hazards. This is especially true of localities where there is an inclination to restrict the extension of 2,300- and 4,000-volt circuits into the mines. Probably it is feared that accidental contact with the cables of such circuits may result in more serious shock than with lower voltages; also, it is possible that new circuits are regarded merely as explosion hazards additional to those already existing, regardless of the manner in which the new circuits may be installed. It is the firm belief of some engineers that the circuits can be installed so that they will not be damaged by wrecks or roof falls, thereby eliminating the hazard of explosion from this source while at the same time making the chance of accidental contact remote if not impossible. Moreover, some believe that fire hazards from direct-current systems can be reduced by keeping motor-generator sets close to load centers. Thus, although the alternating-current circuits would be lengthened, the size and extent of direct-current circuits would be kept to a minimum.

Jan 1, 1939

By J. Chai, Q. Yuan, B. Qiu

"Overburden strata deformation monitoring is one of the key problems in ground control. Using geophysical method through surface drilling to detect strata deformation is commonly used in the industry. In this paper, a geophysical method based on the distributed optical fiber sensing (DOFS) system were conducted in the laboratory, where a DOFS-based strata deformation monitoring experiment was performed with three physical models. The results show that the DOFS method precisely detects the rock mass deformation and strata structure forming with the Brillouin frequency shifts (BFS) representation. The BFS curves are divided into three phases, which reflects the horizontal three zones developed in the overburden. The BFS distribution presents a multiple stages form, the 1st stage corresponds to the caving zone and the 2nd stage corresponds to the fracture zone. Based on the multiple stages form, the evolution of the water flowing through fractured zone have been determined and the controlling effect of key strata over the water flowing fracture has been pointed out. In the end, the comparison validation proves the accuracy and reliability of this method, and it could be a new approach for the ground control research. INTRODUCTION Overburden rock strata above the work face space will propagate from slight deformation, part destruction to violent movement because of the underground coal mining. It is fundamental and an intrinsic requirement of ground control to monitor the mining-induced rock mass deformation.[1] Overburden strata have their significant mechanical behaviors and movement under damage deformation and fracture. Overburden strata deformation affect the mining ground pressure control directly, and performance in the relationship of supporting equipment and the surrounding rock, the mining-induced fracture distribution and the loss of underground water resource, the ground surface structure stability and the ecological environment.[2] From the perspective of the concept of safe and efficient scientific coal mining: the overburden strata deformation is an important part of mining method selection and reasonable supporting solutions decision which can solve the issues like the roof supporting force calculation, overburden fracture distribution and gas drainage, ground subsidence, separation of coal and rock control and top-coal recovery rate and so on. From the perspective of green and ecological mining: the overburden strata deformation is the key basis of studying the mining-induced ground subsidence and mining area ecological damage, and such engineering problem like environmental protection in mining area, ecological restoration in mining subsided land and the water conservation in fragile ecology area of mining could be solved based on it.[3-6] Therefore, the mining-induced overburden strata deformation is the key of ground control and needs to be controlled artificially."

Jan 1, 2017

By R. J. Evans

The generation and disposal of solid waste from electric utility plants using a lime or limestone wet-scrubbing system and the potential effects on the environment were estimated for 1975 and 1980. The study indicated that in 1975 approximately 5.8 million tons of desulfurization solid waste (50 percent solids) will be generated. In 1980, when it is estimated that desulfurization will become commercially accepted, approximately 71.4 million tons of this material will be generated for disposal and/or utilization. The desulfurization waste material when combined with lime, fly ash, and water may have potential for use as a roadbase material, landfill reclamation, and synthetic aggregate.

Jan 1, 1974

By William H. Pomroy

Fires in underground metal and nonmetal mines pose a threat to the safety of underground miners and to the productive capacity of this Nation's mines. Contaminated air (smoke, carbon monoxide, and other products of combustion) is the primary life safety hazard created by a mine fire. The most reliable defense against the hazard posed by the rapid spread of contaminated air underground is early warning fire detection and rapid evacuation. This Bureau of Mines report describes the design and operation of four prototype early warning fire detection systems, for underground noncoal mines, presently undergoing prolonged in-mine testing by the Bureau. The systems are described within the context of the underground mine environment.

Jan 1, 1985

By Thomas D. Boyce

Minewater from many western U.S. uranium mines often contains radioisotopes in concentrations higher than permissible for discharge to unrestricted areas. .Radium 226 has the lowest permissible concentrations of all radioisotopes and usually greatly exceeds this limit in untreated effluents. This radionuclide is derived from the natural radioactive decay of uranium: [ ] The treating of minewater effluents has been studied previously (1) and the classical removal method for radium has been adsorption on barytes or freshly precipitated barium sulfate. This paper describes the removal of radium from minewater by utilizing a selective complexer based on a crosslinked organic polymer matrix.

Jan 1, 1982

By D. P. Bryan

The identification and-develop¬ment of new construction aggregate resources, the most common mineral mined, is an essential need in this country's growing urban areas. In developing an aggregate exploration program, a thorough geological identification of all potential aggregate resources in an area is still of primary importance but other factors have also to be considered. These include physical properties, end product application, transportation and mining costs, and local government regulations including zoning. The present major aggregate producers are most likely to develop these future resources and are in the best position to initiate comprehensive exploration programs.

Jan 1, 1987

By Martin C. Kuhn

The use of tritium in manufacturing and its subsequent loss to the local environment in Tucson, Arizona resulted in a great debate relative to the physiological effects of low level radiation. This paper reviews some of the facts of the release and attempts to quantify the degree of hazard encountered by the local community. Some of the difficulties in assessing the true degree of absorbed dose and the assumptions necessary for calculation purposes are presented.

Jan 1, 1981

By D. F. Suarez

Spontaneous nodulation leading to growth of well developed glossy spheroids (generally hemispheres) of up to 0.06 cm width in 120 min has been observed during copper electrodeposition with certain levels of glue, thiourea and C1-. Thiourea alone can produce spontaneous nodulation but addition of glue and/or Cl- is required for rapid and sustained growth. In most cases once the glossy nodules develop they consume the majority of the copper deposited; thus, the specific current densities (and hence copper electrodeposition rates) on the glossy nodules are about an order of magnitude or, more greater than on the adjacent planar surfaces. The texture of the adjaoent planar surfaces is not glossy in appearance but is well faceted showing the usual deposition grain structure for such additives. Cathode potentials when spontaneous nodulation occurs are about TOO my more negative than with usual copper electroplating. This fact associated with evidence of extremely high levels of cathode surface passivation based on cyclic voltammograms indicates that the conditions which lead to spontaneous nodulation result from a very tightly adsorbed additive surface film. This film breaks down in specific points initiating the glossy nodules which then grow at extremely rapid rates. Current density is also important in spontaneous nodulation. At equal deposition times a current density of 21.5 mA/cm produced much larger glossy nodules than at 48 mA/cm2. The surface concentration of the glossy nodules was much greater in the latter case, however. The role of current density is still not well understood. The role of it as well as the relative roles of the three additives, thiourea, glue and Cl- in spontaneous nodulation is presented. Preliminary results and some possible correlations of these to help explain spontaneous nodulation are presented. It is believed that tankhouse upsets where cathode nodulation occurs may be related to this phenomenon.

Jan 1, 1987

By George L. Richert

The Minas de Matahambre is situated on the north coast of Cuba, in the Province of Pinar del Rio, approximately 150 miles west of Havana. This nine is the only producer of copper in Cuba, and has been worked for the past 15 years. In 1921 the property was affiliated with The American Metal Co., Ltd., and has been worked by them since that time under the direction of Mr. D. D. Homer, General Manager. Extracts from P. D. Wilson's ?Preliminary report on the geology at Minas de Matahambre? have been freely used in this report.

Jan 1, 1929

By H. Marquis

This paper is concerned with an analysis of a number of failures of large-size, hypervelocity light gas gun chambers and barrels. A brief description of the light gas gun principle and of the various types of guns is first given. The failures and the investigations carried out are then described in detail, with the failures divided into two groups. The first group comprises those failures caused by certain conditions to which the guns may be submitted, and includes, for example, severe local heating of the bore surface causing hardening and cracking of the steel. These conditions were accidental and steps were taken to prevent them. The remaining failures were due to faults in the material or in the heat-treatment, manufacturing or assembling procedures. Specific problems, such as hydrogen embrittlement, and the use of high strength gun barrels above their ductile-brittle transition temperature by preheating prior to firing, are briefly considered. Some interesting observations are also presented on the use of surface markings, and angles of fracture of large fragments, as an

Jan 1, 1962

By Douglas J. Lootens

Geologic mapping was undertaken in the Sierrita Mountains as part of a Doctoral program at the University of Arizona, Tucson. During the study, approximately 35 square miles was mapped in detail, with particular attention given to specific areas of great or significant structural complexity and their relation to mineralization in the vicinity. A combination, of field studies and photogeologic interpretation was used in order to define regional and local structural controls for disseminated copper-molybdenum mineralization in and adjacent to the study area. Gratitude is expressed to the faculty of the University of Arizona, Department of Geology for their assistance in this work and to Bear Creek Mining Company for making numerous reports and drill cores available for study.

Jan 1, 1965

By Kevin J. Ashley

Coal is deposited at a mine site in several thin seams which outcrop in rolling hills and dip at about 8° to the northeast. The deposit is located in the northeast area of the State of New Mexico in the Southwest of the United States. A drilling program was undertaken and was quite irregular. Not all of the seams appear in all of the drill holes. Some of the holes did not go deep enough, while others were drilled below the outcrop of some seams. Occasionally a seam would pinch out and not be seen in a drill hole. Also, the outcrops of the seams are buried in many places by several feet of alluvium. All of these factors make correlation of the seams between drill holes difficult. The drawing of cross sections in three directions and at many locations across the mining area have been necessary to assure the accuracy of the input data.

Jan 1, 1982

By Patrick J. Hannigan, William H. Walton, Ryan C. Rusk, Van E. Komurka

"The project consists of a 33-story building with two levels of below-grade parking across the entire building footprint. Timely and cooperative teamwork among the owner/developer, geotechnical engineer, testing agency, structural engineer, construction manager, and pile-driving contractor resulted in an efficient, costeffective, high-capacity driven-pile foundation on a constrained urban site with significantly variable subsurface conditions. Design objectives included utilizing the highest allowable pile loads reasonably installed from a drivability perspective, using readily available equipment. A pre-production test program was performed on 16-inch-diameter (406-mm-diameter) steel pipe piles, driven closed-ended and subsequently filled with concrete. The test program included dynamic monitoring of 10 piles during installation, and of select piles during long-term restrike testing with a drop hammer, with one instrumented static load test. CAPWAP® analyses were performed on both end-of-initial-drive and beginning-of-restrike dynamic test records. The site exhibited significant soil set-up, even after relatively short wait times. Testprogram objectives included characterizing set-up profiles. A design set-up profile was used to develop depth-variable driving criteria for both 500- and 600-kip (2,224- and 2,669-kN) allowable load piles. Test program results permitted more-accurate reduced capacities to be assigned to damaged piles, and to piles which experienced practical refusal. These more-accurate assigned reduced capacities decreased the number of replacement piles required by 50 percent, saving both time and cost.PROJECT DESCRIPTIONThe project, located in Milwaukee, Wisconsin, USA consists of a 33-story mixed-use residential building with two levels of below-grade parking across the entire site footprint. Column service loads range from 1,400 to 4,200 kips (6,228 to 18,683 kN). The project is located immediately adjacent to an existing two-story masonry retail building with a partial basement, supported on shallow spread-footing foundations.Subsurface Conditions – The generalized soil conditions are presented in Fig. 1. Site grades were relatively level, with a ground-surface elevation of approximately +53 feet (16 m), Milwaukee City Datum (“MCD”). Fill material from previous construction was encountered to approximate Elev. +33 feet (10 m). Below the fill, medium dense silty sand, to silt with sand, was encountered to approximate Elev. +23 feet (7 m). Underlying deposits consisted of lean clay, with undrained shear strengths ranging from approximately 1,000 to 3,000 pounds per square foot (psf) (48 to 144 kPa). Silty sand, to silt with sand, exhibiting increasing relative density with depth, was found below the lean clay to approximate Elev. -92 feet (-28 m), where hard lean clay (glacial till) with undrained shear strengths in excess of 5,000 psf (239 kPa) was encountered. Borings did not extend below Elev. -103 feet (-31 m)."

Jan 1, 2017

By Irving Hartmann

When permissible explosives are used in coal mines according to the procedure recommended by the Bureau of Mines they are relatively safe, and no mine explosions are known to have resulted from this type of blasting. However, unsafe blasting practices - the use of nonpermissible explosives or the improper use of permissible explosives - have caused many serious disasters. In fact, such unsafe practices constitute the third most important cause (exceeded only by electricity and the use of open lights and smoking) of coal-mine explosions in the United States. During 1929-1947, inclusive, 81 explosions, resulting in 475 fatalities, were ascribed to unsafe blasting. The hazards of black powder, dynamite, and other nonpermissible explosives in coal mines have been recognized for many years, and attention has been called to this in numerous Bureau of Mines publications. Not only can these explosives ignite namable gas-air mixtures readily, but they can also ignite coal dust, as has been illustrated repeatedly in tests and at educational public demonstrations at Bruceton and elsewhere.

Jan 1, 1952

By V. J. Lynch, A. L. Peyton

"INTRODUCTION AND SUMMARYThe Brewer mine, near Jefferson, Chesterfield County, S.C., was originally operated as a gold mines as late as 1890 this mine was reported to have been one of the large gold producers in the southeast,Occurrence of topaz on the Brewer property was not reported until 1935, when it was discovered by Pardee and Parks. 3/ of the Federal Geological Survey while they were investigating gold deposits in the Piedmont province.During the 1940's the Chemical Engineering Branch of the Tennessee Valley Authority and the Electrotecbnical Laboratory of the Bureau of Mines at Norris, Tenn., investigated topaz from the Brewer mine to determine the possibilities of its use as mullite and for the production of calcium fluoride.From July 1950 through. April 1951 the Bureau of Mines conducted a diamond-drilling project at the Brewer mine to determine the grade and extent of the topaz deposits. Ten diamond-drill holes, totaling 2,344 feet, were completed, and 231 analyses of core samples were made during the course of the project.This report presents factual data relating only to the diamond-drilling project, The placer deposits on the Brewer property were previously investigated by the Federal Geological Survey 4/."

Aug 1, 1953

By H. E. Cross

In a minerals-recovery context, the object of exercising control over milling operations must be threefold, 1) To achieve maximum recovery at 2) minimum operating costs and 3) making maximum use of installed equipment, Milling is one of a sequence of operations which have as their objective the economic recovery of minerals from mined ores, All operations in the sequence are interdependent and each is both influenced by and itself affects all other unit processes. The part which grinding plays in achieving each of the above objectives is indicated in the following analysis: In South Africa, the most important mining operations are still the gold mines, A vast reservoir of knowledge and experience in treating the Witwatersrand and associated ores has been accumulated. and recoveries are consistently high, However residue values do vary and frequently this is due to fluctuations in the degree of grind, The significance of changes in residue values is indicated by the following example: On a modern mine, the residue values varied from 0,25 to 0,33 dwi; per 2000 lb, during a period of 6 months, The cash value of the gold thus lost varied therefore between $0.44 and $0.58 per 2000 lb, ton. A residue which assays 0.30 dwt per ton would contain approximately 0.26 dwt as undissolved gold and 0,040 dwt per ton as dissolved gold present in residual solution after filtration. This dissolved gold loss is a function of efficiency of filtration and varies from 0.030 to 0,.070 dwt per ton of residue.

Jan 1, 1970

By M F. Lee

Although the Mt Charlotte gold resource was discovered in 1893, it was only in 1954 that geologists correctly interpreted drill data and defined a large low-grade orebody. The mine has been a large, low-cost and profitable producer since 1962 when bulk mining commenced using cut and fill. From 1968 a combination of long hole open stoping with delayed mass blasting was used. This proved to be an excellent mining method for the large, separate subvertical orebodies. The structured but otherwise good quality rock allowed very large stopes to stand unsupported. Exceptionally large equipment, for its time, was used to efficiently mine, muck and move the ore at low-cost. The mine only just survived severe cost pressures in 1974-76, due to very low gold prices. Better gold prices in 1979 and a need to access deeper ore meant a bold commitment to sink the Cassidy Shaft and refurbish the mine to sustain future profitability. In 1997 the Sam Pearce Decline connected to the underground workings, making it profitable to mine upper level remnant ore. Mining-induced seismicity has been a feature of mining at Mt Charlotte. The main cause has been shearing on structures. A mine-wide seismic system was installed in 1994. Large seismic events have occasionally made management question whether a safe working environment can be maintained. Thorough investigations led to an understanding of the problem and development of procedures to minimise seismicity.

Jan 1, 2000

By M. W. Von Bernewitz

Corduroy is used for saving gold in small Land large milling plants throughout the world. Investigations by the Metallurgical Division of the Bureau of Mine indicate that corduroy blankets, used with or without a trap or jig in the mill classifier circuit, often are effective in concentrating gold and sulfides, especially if the gold does not amalgamate readily and if not enough sulfides are present to warrant the use of a shaking table, flotation cells, or cyanide plant. Most cold-mining countries include several or many small miner, that produce siliceous ores low in sulfides and gold, which can easily be amalgamated or caught in traps or jigs or on corduroy and shaking tables. At these mines the ore is crushed by stamps or bill mills, and the flow sheets include plates, flotation cells, and cyanide treatment, yet probably nearly as much of the pair minerals may be recovered by the less expensive plant. A well-known western maker of mine and mill equipment asserts, as the result of considerable observation of installed plants, that old and other valuable minerals should be caught as soon as they have been released by a mill, end recommends jigs to do this. A supplier of corduroy has informed us that at some mines this material is being replaced by jigs that catch gold as fine as 400-mesh. But for the small operator, inexpensive equipment such as a corduroy table may be better adapted and give a good recovery of gold and associated minerals.

Jan 1, 1939

By G. V. Borquez

For many years drilling and blasting has been considered more of an art than a science. This is still true in some respects, but today scientific approaches to drilling and blasting design must be used to plan an efficient operation which achieves desired fragmentation within constraints. These constraints involve minimizing damage to the wall or nearby permanent structures and avoiding undesirable fragmentation and mine dilution which can adversely affect operation costs. The degree of fragmentation by blasting is the most important single factor in any attempt to optimize the overall cost of the mining operations. The mining cycle begins with the drilling and blasting operations, which result in a given blasted rock size distribution. While this operation represents only about 20% of total mining costs, the efficiency and costs of the subsequent operations are strongly dependent on the fragment distribution obtained.

Jan 1, 1986

By H. Lundberg

Introduction The world has been suffering from an excessive production of all kinds of raw materials, and the metals and petroleum are no exception. As a consequence, at the moment, the urge to find new mineral deposits is almost non-existent and prospecting languishes. But from previous experience we know that sooner or later new supplies will be needed. Mineral deposits become exhausted, and to keep up the supplies of our metals and petroleum, new deposits must be found. Even now, a supply of petroleum of domestic production would not be unwelcome in Canada. It is not, therefore, so entirely malapropos to discuss means of finding ores and oil as it would seem. Almost any physical property connected in definite manner with minerals and rocks may be made the basis of geophysical exploration. This is particularly true of electrical resistivity, and its utilization in electrical prospecting has been the deciding factor in the discovery of such big ore-bodies as Buchans mine, Newfoundland, and the large copper ore-bodies in northern Sweden, etc., as well as in the solution of many foundation and structural problems. The importance of electrical prospecting has been growing steadily, and already there exists hardly any exploration project involving geological problems which may not profit by its application. Electrical prospecting is marching on, and neither temporary failures, nor incompetence, nor over-optimism, nor ill-will and pessimism, nor bad times and business depression, will be able to halt its progress.

Jan 1, 1931