Search Documents

By Jerry T. Shelby

Surface and underground mining operations require equipment with high power output ratings. Haul trucks, loaders, dozers, and other equipment need increasing horse-power to meet production demands. To get more horsepower out of the engines driving the equipment, most manufacturers use turbocharging. Detroit Diesel puts the number at about 90% turbocharged, while Caterpillar estimates 75% to 80% of all its equipment is turbocharged. Turbocharging increases the power output and overall engine efficiency. But it presents some maintenance and operational problems that were not factors when only naturally aspirated engines (nonturbocharged) dominated the scene. A turbocharger is an exhaust-driven air compressor. Using the waste energy in the engine exhaust, a turbine wheel is driven. This wheel is connected by a common shaft to a compressor wheel. The shaft is supported by two plain bearings, or bushings. As the turbine wheel is rotated, the compressor wheel continually compresses the intake air to the cylinders. Compressing the intake air means that more air can be put into the cylinder to burn more fuel. The more fuel the engine can completely burn or combust, the more horsepower the engine can produce. Even though the turbocharger is a relatively simple device, it is a sensitive engine component. It requires special consideration at engine start-up and shutdown. Being freewheeling and exhaust driven, turbochargers can experience temperatures of 540°C 1000°F) and rotational speeds of more than 100,000 rpm. Due to those temperatures and speeds, lubrication is critical to the operation and life of a turbocharger. The turbo is located high on the engine, with the oil supply running through an external line from the sump. The recommended practice is to start the engine and allow it to idle for a few minutes before any revving or loading. This allows the oil to reach the turbo and properly lubricate the bearings before high rotational speeds are seen. Turbo oil supply lines can be as long as 1.5 m (5 ft). Depending on ambient temperatures and oil viscosity, it can take as long as 30 seconds for oil to reach the spinning turbo. However, as little as five seconds without oil can damage the turbo's bearings, reducing its life and overall efficiency. Lubrication problems seen at shut-down can also significantly affect turbo life and efficiency. Manufacturers recommend an idling period of five to seven minutes before engine shutdown. This allows the turbo to slow down and cool off somewhat to help prevent oil coking and bearing damage. When the engine stops, so does the oil supply. There is very little oil left on the bearing surfaces and in the turbo oil supply passages. The immediate heat transfer from the turbine wheel to shaft, bearings, and turbo body literally cooks what is left. This high heat without oil flow can cause bearing deformation by actually melting some of the bearing material. The rapid oil oxidation and coking will restrict oil passages, damage bearings and shaft. Besides heat soaking, there is another problem. If the turbo is spinning at high speeds when the engine is shutdown, the turbo must spin-down to a stop without oil flow. With the large size of turbos used on mining equipment, this spindown time without oil can be for as long as 10 to 20 seconds. Fortunately, lack of lubrication at start-up and shutdown and the subsequent bearing damage can be prevented by oil injection devices. These devices hold a reservoir of engine oil. The oil is injected to the turbocharger bearings immediately on start-up and for several minutes after shutdown. Oil injection devices are spring loaded, hydraulic accumulators. They are actuated at start-up by a solenoid wired to the starter motor. Engine oil pressure charges the accumulator during normal operation. Upon shut-down and loss of oil pressure, the device provides oil to the turbo for about two or three minutes. With an oil injection device, the engine can be started and immediately driven without fear of turbo damage. Also, an abrupt shutdown will not damage the turbocharger since the device will continue to lubricate for two or three minutes. A word of caution. Be sure the oil injection device provides positive oil displacement (pressurized oil flow). Do not use a gravity-flow device. Unless it is a true accumulator, the device could starve the turbo for oil on start-up, Ask for start-up and shut-down pressures and delivery times before considering installation. Keep the oil clean, and follow the manufacturer's recommended oil change intervals. These intervals are usually shorter than with naturally aspirated engines. Use oil with a CD rating designed for diesel applications. A multiviscosity oil is preferable. Use a synthetic engine oil, such as Mobil's Delvac 1, Gulf's Super Duty II, or Chevron's Sub-zero Fluid. Synthetics have much better flow properties at low temperatures. They also have greater oxidation stability (they can take the high heat of turbo-bearing lubrication. And they produce fewer deposits because they are more thermally stable. But synthetic oils do cost more - two or three times more. One additional point - maintain the air intake system. Since all mining is usually in a dusty environment, air filters should be changed regularly and intake systems should be checked for leaks. All intake air passes through the turbo. Any dirt or abrasives entering the turbo will damage the unit and shorten its life. While mining is a heavy duty business with severe operating conditions, you can get the life from your turbocharger that you expect by following a few simple steps: • equip the turbo with an oil-injection device to provide lubrication on start-up and shutdown; • change the oil and filters regularly; and • use the proper oil-synthetic, if possible.

Jan 3, 1987

By M. L. Klohn

The Felder ore deposit is a 5,000,000-pound uranium deposit in the South Texas Coastal Plain. It occurs in the basal sand of an Oakville Formation (Miocene) alluvial system. The host sand is a carbonate-rich arkose which contains virtually no carbonaceous debris and has been reduced by the local introduction of hydrogen sulfide. The ore lies well within the reduced zone and occurs as coffinite and uraninite that fill interstices and coat and replace grains. The overall geometric configuration of the ore is that of a winged, crescentic ore roll. Weak mineralization extends the wings of the ore roll and gives greater expression to the roll character. Departures from the shape are controlled by discontinuities in bed- ding and by proximity of the ore to the surface. Associated with the uranium is a broad halo of anomalous molybdenum. Subsidiary mineralized trends suggest a pre-existing up-dip position for the main roll. Oxidation from the surface largely destroyed this previous roll by solubilization of uranium. Uranium subsequently migrated into favorably reduced sand and reprecipitated at the present roll position.

Jan 1, 1970

By Robert S. Warfield

Eight samples of high-volatile bituminous coal, each large enough for a study of its coking properties by the Bureau of Mines, were obtained from a location along the Kukpowruk River, Arctic Northwestern Alaska. Bench scale and pilot plant carbonization studies with several patterns of coal blending were conducted. The data from these tests were compared to data from similar tests on a coking blend used by the Kaiser Steel Corporation at Fontana, Calif. The majority of the samples representing the 20-foot seam was found to have significant coking properties, and produced coke approaching metallurgical quality when blended with selected coking coals. Although oxidation effects were evident in the samples representing upper portions of the seam, it appears that the whole seam could be used.

Jan 1, 1966

By William W. Adams

The stone-quarrying industry of the United States, including such related operations as rock crushing, rock dressing, and the manufacture of cement and lime, reported a larger volume of employment in 1934 than in 1933. Reports from the operating companies to the United States Bureau of Mines showed an increase in the number of men employed, number of man-days of employment, and total number of man-hours of labor performed during the year. Moreover, the average worker had a longer period of employment during 1934, the gain amounting to 11 percent over 1933. The increase in employment was accompanied by no increase in accidents for the industry as a whole; in fact, the accident rate for 1934 was a fraction lower than the rate for 1933. In some branches of the industry the frequency of accidents increased, but these increases were more than offset by reductions in rates for other branches. Reports for 1934 were received from 1,403 active plants. The working force averaged 64,331 men for 204 days per man, and the total period of employment for all of the men was 95,258,880 man-hours. Each employee averaged 1,481 hours of work during the year. The total number of hours of labor represented a gain of more than 8 percent, and the average working time per employee showed a gain of 62 hours per man.

Jan 1, 1936

New Copper Deposit in Chile. - The recent copper discovery in Chile, made jointly by U.S.-owned Empresa Minera Utah de Chile, Inc., and Getty Mining Chile), Inc., awaits the passage of Chilean legislation which is expected to govern the terms of new foreign investment in the country's mining sector. Named La Escondida, the discovery is reported to have the potential for producing 100,000 tons of refined copper per year. This compares with Chile's total refined primary copper production in 1980 of 811,000 metric tons, and to U.S. refined primary production in 1980 of 1,122,000 metric tons derived from domestic material, and 89,000 metric tons from foreign material. U.S. Firms Buy Chilean Properties. - A bid of $18.1 million, made jointly by Chevron and St. Joe Minerals Corp., won over competing bids for the purchase of the Libra and Mena gold-silver-copper deposits in northern Chile. Chevron is the lead partner and owns 70% of the venture. The two properties purchased have not been developed to any significant extent. They are located near St. Joe's El Indio gold-silver-copper mine. The venture is also looking at the possible purchase of two other mines in the area.

Jan 1, 1981

By Paul M. Tyler

In 1939, American industry got, off to a poor start, slowed down further during the first quarter, quickened after May, speeded up still more when war broke out again in Europe, and ended the year at a pace close to an all-time record. The average index of general business activity for the entire year (105) was well ahead of that for 1938 (86), failed to equal that of 1937 (110), and fell behind the average for 1929 (119) by a wide margin. (Federal Reserve Bank yearly indexes in parentheses).

Jan 1, 1940

By Alton B. Cook

In the Scurry Reef field, Scurry County, Tex., a study was made to determine the physical properties of the oil in all parts of the reservoir by a new method developed for this study. The method involved correlation of data from a survey 1 of the gravity of the produced oil, from measurements of gas-oil ratios on key wells selected to give representative data for the entire reservoir, and from laboratory analyses of reservoir oil samples. A field survey was made of the API gravities of the produced oil by testing oil samples from 107 key wells. Precise gas-oil-ratio tests were made on 45 key wells that were producing under comparable separator-operating conditions. Subsurface-oil samples were obtained from seven wells, selected to provide reservoir oils ranging approximately from a minimum to a maximum in saturation pressure. The physical properties of the subsurface-oil samples were determined, and correlations were made of these laboratory data with the field gas-oil-ratio test data. These correlations were then used to estimate physical properties of the oil throughout the reservoir. A logical procedure of determining the variations in physical properties of reservoir oils in most fields is to obtain and analyze subsurface-oil samples from enough key wells to provide an ample coverage of the field. Under this procedure, data from a large number of samples would be needed to provide the desired information on the Scurry Reef field, as it is one of the largest known in the United States.

Jan 1, 1955

This report summarizes the cost of U.S, mining and milling industry compliance with the Environmental Protection Agency (EPA) interim water quality guidelines for waste discharges. Applicable excerpts from Public Law 92-500 are stated and interpreted in conjunction with the guidelines being used for implementation of the law. Over 200 U.S. Army Corps of Engineers applications for discharge permits were used to develop the quality and quantity data base needed to estimate the cost to comply with EPA guidelines, Cost of three basic treatment methods were considered: Aeration, addition of lime, and sedimentation. From the process design, cost-capacity graphs were developed to consider maximum flow rate, maxi lime addition, and average flow rates. The graphical method used in this evaluation should provide a reasonable guide to the effect of waste treatment and, therefore, Public Law 92-500 and corresponding EPA guidelines on the mineral processing industry. The cost of complying with the EPA guidelines will have the effect of prompting the mining industry to minimize the production of waste water and of undertaking some additional treatment, Two case studies are presented to illustrate efforts that might be fruitful for minimizing waste water production and for treatment of combinations of acid mine drainage, mill wastes, and metallurgical process wastes when treatment is deemed necessary.

Jan 1, 1975

By Will H. Coghill

This paper on milling methods and costs at a flat river (Mo.), mill is one of a series of information circulars on milling methods and costs which is being prepared by the United States Bureau of Mines, The mill under consideration treats 5,000 tons of load ore daily by table concentration and flotation. It is 25 years old, and yet it is a new mill. Research has been in continual progress at the plant since its beginning, and accordingly a day never passes without a record of change for advancement. The changes have been so orderly that no evidence of obsolete equipment remains.

Jan 1, 1932

By W. W. Adams

[The sfxteeith e-mud ?7ntior_,il SnS~ty Cn~potitior,, cohduc ted by th Bureau of Mines, United Stntes'I3epnrtzel?t oL' the Interior, hstc fist been closed, and the resvlt s reveal tbt t!:e co~yafir,~ compzniqs had fewer accir'.ents in prnyort?lon to t2.o numbcr,of nkr-l:q?lr~1 1:9:='czd thm in my other ycryx in t3o r~cordc of the conlcst, Pheco zrzu-J. con:estn me thus aclr,i-cvir.c; Shc?r purpoao of ~romo tine w.fe ty in t5c nip-i~y induc tq*.]

Jan 1, 1941

The U.S. economy continued to expand during 1986, although at the slowest pace since 1982 when the current business expansion began. Real gross national product (GNP) grew about 2.6%, slightly below 1985 growth but significantly below that of 1984. The continuing expansion was fueled pre-dominantly by rising personal consumption expenditures as well as growing Government purchases of goods and services. Fixed investment, although positive, failed to grow at the rate of the overall economy. The trade deficit, which increased more than 30% over the record 1985 level, continued to depress economic growth despite significant declines in the price of petroleum and the value of the dollar. On a more positive note, domestic employment continued to grow--increasing over 2 million from the 1985 level--and inflation and interest rates declined. The unemployment rate dropped slightly to 7.0%. Of direct importance to the mineral-producing industries, expenditures for consumer and producer durables as well as investment in residential construction each grew faster than the overall economy, but investment in nonresidential structures fell more than 10% from the 1985 level. The level of real capital spending declined about 3% in 1986, following strong gains in 1985 and in 1984. Capital expenditures for new plant and equipment bottomed out in the second quarter and expanded in the third and fourth quarters. The decline in the first half of the year was partially attributed to uncertainty arising from the then-proposed tax bill. Also, there was little impetus for corporations to invest in new capacity since factories were operating at less than 80% of capacity during most of the year, in part because of continued competition from imports.

Jan 1, 1986

By F. D. Wang

This report presents a structural-mesh-generating computer program for the two-dimensional finite-clement method of mine structural analysis of single and multiple openings in nonhomogeneous rock mass. This program greatly reduces the amount of input data required and the chances of error which otherwise are large owing to the large amounts of data and the complex mesh involved. The program description, a user's guide, example problems, and program listing are included.

Jan 1, 1971

By Wallace W. Key

The California pesticide industry in 1962 consumed about 30,000 tons of clay, talc, limestone, diatomite, sulfur, and other minerals as fillers (carriers and diluents) in pesticide formulation. This was 10 percent of the U.S. filler requirement for pesticides. About two- thirds of the California total was supplied by a few local mineral producers; the remainder came mainly from Florida, Georgia, and Wyoming. The objectives of this report are to provide data on quantities, sources, specifications, and market conditions for minerals used as fillers by California pesticide formulators. The study disclosed that specifications for mineral fillers have become more rigid and formulators have become more numerous in recent years. During 1962 over 1,200 firms registered 16,000 pesticide products with the Bureau of Chemistry in California. Factors which will tend to diminish future need for mineral fillers include the trend toward greater use of organic sprays rather than dusts and further development of biological controls, such as the development of sterile insect strains.

Jan 1, 1965

By Pedro Lilienfeld

This report describes a program to develop, design, fabricate and subject to environmental testing three prototype collection-sensing devices of an eventual mining-machine mounted automated monitor for the measurement of the respirable fraction of coal mine dust to determine both short-term as well as average mass concentrations over typical 8-hour shifts. The design of this instrument is based on collection by filtration and mass sensing by beta-radiation attenuation. The emphasis of this development program was to evolve a rugged, stable and reliable collection-detection head compatible with the environment to which An eventual monitor will be subjected. Laboratory testing of this prototype instrument was performed over a representative range of temperature, humidity, dust concentration and composition, shock and vibration. The results of this testing program indicated that the operation of the prototype version His compatible with these environmental conditions and that further development of this configuration into a field operational device is justified.

Jan 1, 1977

Data released by the Commerce Department's Bureau of Economic Analysis show continued gradual change in the real GNP's rate of growth in 1984, which has eased from an annual growth rate of 10.1 percent in the first quarter lo 7.1 percent in the second quarter, and then to 2.7 percent in the third quarter. The automobile industry strike in the last half of September had only a small effect, estimated at less than a 0.1 percentage point reduction in the growth rate. Among the components that comprise the GNP, personal consumption and fixed investment grew at lower real rates in the third quarter than in the second quarter, while net exports decreased. Personal consumption expenditures increased $0.4 billion in the third quarter, compared with an increase of $20.1 billion in the second quarter. Nonresidential fixed investment increased $3.9 billion in the third quarter, compared with $9.6 billion in the second quarter. The other component of fixed investment--residential investment--increased from $60.8 billion in the second quarter to $61.2 billion in the third quarter. Real net exports of goods and services decreased $1 1.3 billion in the third quarter, compared with a $3.1 billion decrease in the second quarter. Although exports increased from an annual rate of $144.7 billion to $150.2 billion, imports increased much more, from an annual rate of $1 56.2. billion to $172.8 billion (table 1).

Jan 1, 1984

By Michael D. Balen

This Bureau of Mines open file report is one in a series of reports written about the Valdez Creek Mining District (VCM D) as a result of the continuing Bureau of Mines mining district evaluation program. This report presents the results of order-of-magnitude mining feasibility studies. The mining feasibility studies were conducted for mineral deposit models that were based on real and hypothetical deposits that occur in the VCMD. A total of 6b mine models were developed for application to the mineral deposit models. The goal of the feasibility study was to determine the monetary value per unit of minable ore that would cause the simulated cash flow for each of 66 mine models to achieve certain pre-defined rates of return for the invested capital.

Jan 1, 2011

By C. A. Komar

The Bureau of Mines is investigating possible applications of acoustic energy at sonic and ultrasonic frequencies in petroleum production. A phase of this work involves measuring sound velocity through petroleum reservoir rocks. References and abstracts were prepared as a bibliography to make available to others some of the material obtained from a literature search covering the past applications and the present uses of sound. Laboratory and theoretical studies of the various parameters that influence the velocity of sound in porous media account for the wealth of information now available. Velocity of propagation of sound waves in porous sediments as a function of depth is a quantity frequently measured. Velocity logging systems, capable of measuring speed of sound waves in underground formations penetrated by wells, have been developed for interpretative studies. The close relation between acoustic velocity and porosity makes it possible to determine porosity from velocity logs. Most velocity log interpretation in terms of porosity is based on a formula developed by Wyllie and others known as the time-average relation.

Jan 1, 1963

By Joseph A. Cavallaro

This report describes the timed release analysis technique that was developed to serve as a tool for assessing the froth flotation cleaning potentials of fine-size coals. Using this developed technique, 16 coals from 10 different coalbeds were tested. All of the coals included in this study were quite amenable to froth flotation with float coal yields ranging from 80.7 to 99.5 percentage points. Float-and-sink analyses of the coals tested are shown to be of limited value in predicting froth flotation cleaning potential. Generally the float-and-sink analyses indicated a better product could be obtained than froth flotation could provide; although, in four of the coals tested froth flotation results were superior to those expected from the gravimetric analysis. The fixed carbon content of the samples collected was found to correlate with the floatability of the coals. The higher rank coals were the most readily floatable coals while the lower rank coals did not respond quite as well to flotation.

Jan 1, 1965

By Wallace W. Key

The California pesticide industry in 1962 consumed about 30,000 tons of clay, talc, limestone, diatomite, sulfur, and other minerals as fillers (carriers and diluents) in pesticide formulation. This was 10 percent of the U.S. filler requirement for pesticides. About two-thirds of the California total was supplied by a few local mineral producers; the remainder came mainly from Florida, Georgia, and Wyoming. The objectives of this report are to provide data on quantities, sources, specifications, and market conditions for minerals used as fillers by California pesticide formulators. The study disclosed that specifications for mineral fillers have become more rigid and formulators have become more numerous in recent years. During 1962 over 1,200 firms registered 16,000 pesticide products with the Bureau of Chemistry in California. Factors which will tend to diminish future need for mineral fillers include the trend toward greater use of organic sprays rather than dusts and further development of biological controls, such as the development of sterile insect strains.

Jan 1, 1965

By Daniel R. Stewart

The function of the geological engineer is to assist in mine planning and operations by collecting, interpreting, and applying geologic data to the solution of engineering problems. The geologist supports this effort by collecting additional geologic information specifically useful to the engineer. This use of geologic information reinforces the value of mine geology to the mining process beyond the traditional role of orebody definition. Work discussed includes: evaluation of caving strategies at the Climax and Henderson mines; support definition and slope stability at the Climax mine; and some uses of geology in cavability estimation for the Mount Emmons project.

Jan 1, 1983