Search Documents

By Edward Keller

(Canal Zone Meeting, November, 1910.) UNDER the title, Labor-Saving Appliances in the Works-Laboratory, I published a paper1 in which was described how multi-manipulations, in a works-laboratory, and in the furnace-room of an assay-laboratory, can be condensed into single manipulations by applying the proper mechanical devices. For example, I now deposit in, or withdraw from, a muffle a set of 48 cupels as one unit. The front row. (8) of these. are blanks or heaters; the other 40, when they have attained the proper temperature in the muffle, are charged simultaneously with the 40 lead-buttons. Three manipulations here accomplish an operation which by the generally customary method requires 136, and this number is only limited by the size of muffle and cupels. This operation is an enlargement of what I have already described in my former paper, and Fig. I shows the improved implements. In the paper referred to I described a gold-silver bead parting-bath, which is the last of the devices used in regular sequence in practice. This bath was designated as being convenient, but was not a labor-saver properly. Fig. 2 of the present paper shows a new device. Instead of the original tray, there are now sectional holders for the test-tubes, each having a wooden handle on either end, so that the holders may be removed from the boiling bath, and the acid or water poured off from each set of tubes (in this case, 7) without waiting to cool. The tubes, held in place by clutches, as shown in Fig. 3, rest in holes in the base-strip, having a smaller diameter than the tubes. Each holder is stamped at either end with a number, so that the bath becomes further useful by permitting several men to use it at the same time without interference. Apart from the handles, the holders are made of sheet-copper. ' Trans., xxxvi., 3 to 18 (1906).

Aug 1, 1910

By Clarence O. Babcock

Model pillars of limestone, marble, sandstone, and granite, with length-to-diameter (LID) ratios of 3, 2, 1, 0.5, and 0.25 (0.286 for granite), were broken in axial compression to determine to what extent an increase in end constraint increased compressive strength. Radial end constraints of 13 to 23% of the average axial stress in the pillar, produced by solid steel rings bonded with epoxy to the ends of dogbone-shaped specimens, increased compressive strength somewhat above that of cylindrical pillars without ring constraint. However, when the results were compared with those obtained by other investigators for straight specimens of several rock types taken collectively, with LID ratios greater than 0.5, the resulting strengths were not significantly different. Thus, the amount of end constraint produced by the solid steel rings was about the same as that produced by the friction from the steel end plates. In other tests, a radial prestress of 3000 or 5000 psi was applied prior to axial loading by adjustable hardened steel rings to increase the constraint above that obtained for the solid rings. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 3000 psi prestress, was 54.3% for limestone, 40.3% for marble, 44.7% for sandstone, and 23.4% for granite. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 5000 psi prestress, was 74.2% for limestone, 51.2% for marble, 61.6% for sandstone, and 29.7% for granite. These constraints increased the compressive strength significantly above the strength of straight specimens and solid-ring constrained specimens. These results suggest that large horizontal stresses in orebodies mined by the room-and-pillar method should increase the strength of the pillars and allow an increase in ore recovery by a reduction of pillar size when major structural defects are absent. One important objective of the U.S. Bureau of Mines (USBM) mining research program is the rational design of mining systems. In the design of room-and-pillar mining operations, pillar strength is a fundamental variable. It is customary to estimate this strength from uniaxial compression tests of rock samples and to correct this value for the length-to-diameter (LID) ratio of the in-situ pillar. This method of estimating pillar strength corrects for pillar shape but does not consider the effect of a large horizontal in-situ stress field that sometimes exists in underground formations. The purpose of the work covered in this report was to determine to what extent the compressive strengths of model pillars of relatively brittle rock loaded in axial compression were affected by lateral end constraint. In previous work, Obert l used solid steel rings bonded to the ends of dogbone-shaped specimens to study the creep behavior of three quasi-plastic rocks -salt, trona, and potash ore - during a test period of 1000 hr. These rings provided radial constraint during the loading cycle of 20 to 50% of the axial stress for specimens with LID ratios of 2, 0.5, and 0.25. He concluded that (1) "for a quasi-plastic material the end constraint strongly affects the specimen strength, and (2) as D/L increases (length-to-diameter decreases), the specimens lose their brittle characteristics and tend to flow rather than fracture." He also concluded that model pillars constrained by rings were better for use in predicting the strength of mine pillars than either cylindrical or prismatic specimens. This conclusion appears to be valid where mine pillars, roof, and floor are a single structural element. In the present study, 460 specimens of four relatively brittle rocks — limestone, marble, sandstone, and granite - were tested to failure. The study consisted of two parts: (1) the effect on the compressive strength of end constraint produced during the axial loading cycle by solid steel rings bonded with epoxy to the ends of the specimens, and (2) the effect on the compressive strength of increased end constraint produced in part by a prestress applied prior to axial loading and in part by lateral expansion of the specimen during the loading cycle. The first part of this study was reported in some detail earlier.2 EXPERIMENTAL PROCEDURE AND EQUIPMENT Model rock pillars of the sizes and shapes shown in Fig. 1 were broken in axial compression when the ends were constrained as shown in Fig. 2. he straight specimens were broken without ring constraint. The specimens of dogbone shape were broken with (1) solid

Jan 1, 1970

By R. L. Fleischer, W. F. Hosford

Tensile data for coarse grained aluminum Polycrystals suggest that the "grain size" effect is not due to dislocations piled up at grain boundaries but rather is primarily a relative size effect due to surface crystals being weaker and less confined. STUDIES directed at interpreting hardening of poly-crystalline metals normally identify their strain hardening properties with those in some particular type of single crystal.1"4 The recent recognition in face centered-cubic metals of a nearly linear stage with rapid hardening occuring at comparable rates for both polycrystals and single crystals, suggested that the same process or processes determine both cases and hence that there exists some justification for the use of single crystals to understand polycrystals. Further evidence for the above view may be found by an approach initiated by Chalmers:5 By using bicrystals of controlled orientation it is possible to begin to assemble a polycrystal and also to study grain boundary effects in detail. In this way it has been found that a single grain boundary affects easy glide but not the subsequent stage II hardening.6 This result suggests that a sensitive way to observe grain boundary effects in polycrystals would be to vary grain size and measure easy glide. As will be seen, easy glide is only possible for coarse-grained samples, and hence the results will serve to fill in the gap in measurements between single crystals and bicrystals on one hand and fine-grained polycrystals on the other. One problem inherent in comparing single crystals with polycrystals is the uncertainty as to what slip systems are acting in a polycrystal. To compare the two types of samples, rates of shear hardeninn---L. on the acting -planes are needed. and these may be computed only if it is known what particular systems are active. The acting systems were examined for a coarse-grained polycrystal and it will be shown that the systems supplying the preponderance of slip can be determined with little ambiguity. EXPERIMENTAL PROCEDURE Twelve samples of aluminum were prepared by chill casting into a heated graphite mold, followed by annealing at 635° ± 5°C for 24 hr with an 8-hr fur- nace cool, and finally either etching7 or electropol-ishing.' The samples, with a 7 to 10 cm length between grips and 4.4 by 6.6 mm in cross section, were deformed at a strain rate of about 3 10 -3 . per min in a tensile device which has been described elsewhere.5 The composition was reported by Alcoa as 99.992 pct Al, 0.004 pct Zn, 0.002 pct Cu, 0.001 pct Fe, and 0.001 pct Si; nine samples were deformed while immersed in liquid helium and three in air at room temperature. The stress-strain curve for one of the samples (P-1) deformed at 4.2 "K has been reported previ~usl~.~ This sample was selected for determination of active slip systems. Eighteen of the crystals were examined by optical microscopy to determine the angles of slip line traces and by X-ray back reflection to determine orientation. By this means the slip planes were determined and the resolved shear stress factors for possible slip systems could be computed. Finally each sample was sectioned so that after etching, the number of crystals could be counted for each of ten newly exposed surfaces. The average of these ten values will be termed n, the number of crystals per cross section. Values of 11, varied from 1.9 (nearly bamboo structure) to 12.7. Sketches of typical cross sections appear in Fig. 1. RESULTS AND DISCUSSION: SLIP SYSTEMS 1) Determination of Acting Slip Planes—The stress axis orientation and operative slip planes in eighteen crystals of sample P-1, as determined by slip line traces and crystal orientation, are summarized in Fig. 2. For one of the crystals two planes had a common trace. so that the traces alone did not distinguish which plane or planes were slipping. However it was found that the stress resolving factor for the primary system was 0.386, .while that for the most stressed system in the other plane (indicated bv the dotted arrow) is 0.138. It will be assumed tgerefore that only the primary plane acted. Since the orientations were determined after extending the samples 4 pct, the stress axes may be rotated from their original value by as much as 2 deg in some cases. It is interesting to note that in five crystals only one slip plane acted, in eight two acted, and in five three planes were observed—an average of two slip

Jan 1, 1962

By G. Bhat, J. F. Libsch

lsoembrittlement curves depicting the influence of time and temperature in the range 800' to 1260°F (425' to 680°C) on the development of embrittlement in a commercial chromium alloy steel and a commercial molybdenum alloy steel are presented. Two distinct regions of embrittlement occur in the chromium alloy steel: I—at 800' to 1000°F (425' to 540°C) and 2—in the region just below the lower critical temperature. Embrittlement is most pronounced at 800' to 1000°F, decreasing very rapidly with increasing temperature above this region, only to increase again as the lower critical temperature is approached. The data suggest two distinct modes of embrittlement with possible superposition of the two modes at extended embrittling times in the temperature range 1100° to 1150°F (590' to 620°C). While the molybdenum alloy steel shows little susceptibility to embrittlement at 800' to 1000°F (425' to 540°C), considerable embrittlement may occur just below the lower critical temperature. THE subject of temper embrittlement in alloy steels has received considerable attention in the last few years. Points of view on the mechanism of embrittlement differ, however, resulting in part from the incompleteness of the data developed and in part from the speculation regarding the susceptibility of plain carbon steel to temper embrittlement. Libsch, Powers, and Bhat1 carried out short-time embrittling treatments on an AISI 1050 steel and demonstrated that hardened plain carbon steels are quite susceptible to embrittlement when tempered in the range from 850°F (455°C) to the lower critical temperature. The isoembrittlement diagram,' representing the embrittling characteristics of this steel, is reproduced in Fig. 1. It is evident from the shape of the curves shown that embrittlement in plain carbon steel increases progressively with both temperature and time in the embrittling range. A comparison of the isoembrittlement diagram for AISI 1050 steel with that presented by Jaffe and Buffum' for an SAE 3140 steel shows that up to 930°F (500°C) the isoembrittlement characteristics of the plain carbon steel are similar to those of SAE 3140 steel, although the embrittlement is much more severe in the latter steel. Above 930°F (500°C), the rate of embrittlement in the plain carbon steel increases continuously with increasing temperature; whereas, in the SAE 3140 steel, the embrittlement rapidly decreases. The influence of alloying elements upon embrittlement during tempering thus appears to cause a decrease in embrittlement above the region of maximum embrittlement, i.e., 850" to 1000°F. The question naturally arises as to what effect individual alloying elements have upon the embrittling characteristics of the plain carbon steel. Current knowledge on the influence of alloying elements on temper brittleness may be found in the review papers of Hollomon" and Woodfine. Hollo-mon," from the results of other investigators, has shown that, in general, the amount of embrittlement increases with increasing alloy content (except for molybdenum and possibly tungsten and columbium). Jaffe and Buffum," by a comparison of the embrittlement in a plain carbon steel with that of a SAE 3140 steel postulated that the presence of alloying elements in moderate amounts tends to retard the development of temper brittleness. It is difficult to determine what effect chromium has upon temper brittleness, since most of the information available has been based on the combined effect of other elements with chromium, particularly nickel and manganese. However, Wilten, and recently Jolivet and Vidal,' Vida1, and Woodfine have reported that chromium steels are temper brittle, that the embrittlement is reversible with a maximum rate of embrittlement at approximately 975°F (525"C)," and that the susceptibility increases with increasing amounts of chromium. Taber, Thorlin, and Wallacel" have found a large embrittling effect with increasing chromium content in a medium C-Mn-Ni steel. But Hultgren and Chang," from their experiments conducted on synthetically prepared ternary Fe-C-Cr alloys, could not conclude that these alloys are susceptible to temper embrittlement. However, on addition of manganese or phosphorus, these Fe-C-Cr alloys became susceptible, from which fact they concluded that the embrittlement developed in chromium-bearing Fe-C alloys is due chiefly to the presence of these elements. Considerable data are available to show that molybdenum decreases the susceptibility of steel to temper embrittlement. However, its effectiveness in preventing or decreasing embrittlement appears limited to its presence in small amounts. Vidal" has shown that a plain 2 pct Mo steel was susceptible. Hultgren and Chang" also have shown that molybdenum additions in excess of 2 pct to synthetically prepared Ni-Cr steels did not prevent embrittlement. Jolivet and Vidal' and Lea and Arnold found that molybdenum reduced temper brittleness. Lea and Arnold further stated that molybdenum decreased the rate of embrittlement rather than the total amount of embrittlement, whereas Preece and Carter" have shown that the presence of molybdenum greatly reduces the equilibrium extent of the change at a given temperature but does not appear to influence the rate of embrittlement. There appears to be very little information as to how molybdenum by itself affects the temper brittleness susceptibility of a plain carbon steel.

Jan 1, 1956

By Kenneth A. Grace

Introduction The 1980s have not been kind to the mining industry, especially in the United States. As mineral commodities prices plunged, marginal producers were squeezed out and then major players were forced to cut back or close down operations. Base metal miners suffered the most. Gold was all that glittered. As had been the case throughout min¬ing's history, exploration activity was an early victim of these depressed conditions. Mining companies had to economize drasti¬cally and exploration was deemed a nones¬sential activity. Funding for new explora¬tion ventures dried up as mining was seen as a poor investment. A national magazine even proclaimed the death of the industry. Indeed, ignoring matters of independ¬ence of supply and the relationship of min¬eral production to national security, it was argued that mining was but a small cog in the overall scheme of things in the United States. The industry made a relatively small contri¬bution to the gross national output. We were becoming a service industry economy, re¬member? But what of those countries where mining plays a major role in the economic well-being? In some, mining is the national economy. In a few specific cases, special conditions actually brought prosperity. Copper production in Chile is one example. There, high grade copper, low production costs, and a technically advanced industry reaped the benefits of mine closures else¬where. In most other cases, however, par¬ticularly in the lesser developed countries, whole economies were devastated. This article will show what one major mineral producer, Canada, did to ensure the survival and even growth of its minerals exploration activity during these lean years. Background While Canada is among the world's mining leaders, mining is not its dominant industry. Still, it plays a far more important role than in the United States. It is a major earner of foreign exchange, currently accounting for about 25% of the total value of exports. Through spinoffs and a multiplying effect, it is a significant employer. In the far north, particularly, mining is the major nongovernment industry and a leading factor in the opening up of frontier territory. The industry cannot be allowed to die because it is often the main economic underpinning for vast, remote areas. Thus, exploration for new deposits cannot be cur¬tailed significantly without it having a long¬term negative impact on the very fabric that melds such a large, sparsely-populated ex¬panse of country into a nation. Over the years, Canadian governments have employed various means to encourage the development of new mines. Often, these incentives were tax-oriented, such as the three-year income tax holiday that applied to new mines in the 1950s and 1960s. The advantage of the tax connection is that any such incentive policy can be applied across the board to the 10 provinces and two territories that make up the federation of Canada. This is important because mining, except for the two federally-administered northern territories, comes under provincial government jurisdiction. Mining taxation is a complex give-and-take between the central and provincial authorities. In Canada, expenditure on mineral exploration is an allowable cost against reve¬nue for tax purposes. This works well pro¬vided there is some revenue from which to deduct. New exploration companies, those with no income from mining activities, de¬rive little benefit from this type of tax provi¬sion. Similarly, in times of depressed prices and reduced or nonexistent profits, the tax deductibility of exploration spending loses its value even for the major mining compa¬nies. To encourage exploration in Canada during the lean years, a different sort of incentive was required. The instrument used during the 1980s was again tax connected. It became known as flow-through financing or, simply, flow-through shares. When it assumed its final shape, it worked dramati¬cally. Flow-through shares Flow-through shares are so-named because they permit tax benefits earned by a corporation to 'flow-through' to the share¬holder. Basically, when an investor buys a flow-through share and the proceeds de¬rived by the company from this transaction are used for Canadian exploration, the in¬vestor can claim a deduction for tax pur¬poses as if the exploration expenditure was made by him personally. Flow-through shares go back to the early 1970s when Canada revamped its mineral income tax law. At that time, it permitted full deduction of exploration and development expenditures and provided for an automatic depletion allowance of one¬ third of operating profits from mining. There was also the three-year income tax holiday for new mines. New legislation replaced the depletion allowance with an earned depletion arrange¬ment whereby one dollar of depletion was earned for every three dollars spent on ex¬ploration and development. This earned depletion was `banked' during a transitional period (to 1974). After that it could be deducted from resource profits up to a maximum of 25% of such profits in any one year, with the excess carried forward. To promote exploration and mine de¬velopment in Canada, the earned depletion allowance plus the continued deductibility of exploration and development expendi¬tures permitted the recovery of risk capital before taxation. The three-year tax holiday, however, disappeared. Also, mining com¬panies that did not reinvest in exploration lost the depletion allowance benefit.

Jan 1, 1989

By A. M. Starfield

Discussion J. de V. Lambrechts (Fellow): The author's paper is a brilliant follow-up of an earlier paper by Starfield and Dickson.1 I have no quarrel with Dr Starfield's computerization of a complex problem, but I do not believe that he is getting quite the right answers from his programme. My impression is that his predictions about wet bulb temperature increases in very deep mines are over optimistic; in other words, that it will be hotter than Dr Starfield predicts. This is putting my views in a nutshell. This is not the occasion on which to indulge in lengthy argument about the original paper by Starfield and Dickson, but the present paper is, after all, based directly on that earlier paper and if the one fails, the other cannot succeed. I did level certain criticisms at the first paper and cannot say that the authors' replies were very convincing. I do not think it is a sin to admit that I belong to the old school which believes in thorough field experimentation and practical trials and no amount of mathematical manipulation or physical theorizing, no matter how excellent, can make up for inadequate practical confirmation. This, as I see it, is still the crux of the matter. The original paper by Starfield and Dickson still rests on somewhat scanty practical evidence and I would be much happier if Dr Starfield's computer programme, based on the Starfield-Dickson model, had been checked against a large mass of observations in the practical mining situation. This is what both Wiles2 and myself3 had tried to do previously. What we lacked in mathematics and/or computer aids, I think the present paper by Dr Starfield lacks in practical substantiation. This is no condemnation of the author's paper which, taken by itself, is excellent but I think the final stage is still lacking, namely the bringing together of theory and empiricism in a manner acceptable to all. This may be wishful thinking on my part but I hope, within the next year or so, to come up with a modified Starfield-Dickson model in such a way that the computer answers will agree in the majority of cases with the few hundred field observations which are already on record. It might be a case of applying the proverbial 'Cook's Law' to the Starfield-Dickson model! REFERENCES 1. STARFIELD, A. M., and DICKSON,A. J. 'A study of heat transfer and moisture pick-up in mine airways.' J. S. Air. Inst. Min. Metall., 68, (5), 1967. 2. WILES, G. G. 'Wet bulb temperature gradients in horizontal airways.' J. S. Air. Inst. Min. Metall., 59, (7), 1959, p. 339. 3. LAMBRECHTS, J. DE V. 'Prediction of wet bulb temperature gradients in mine airways.' J. S. Air. Inst. Min. Metall., 67, (11), 1967, p. 595. R. Hemp (Visitor): Dr Starfield's paper has very effectively rounded off one particular aspect of the general problem of heat flow in mines. The ease with which this computer programme can be used to calculate temperature increases in horizontal airways must lead to its wider use in ventilation planning and, in developing this rapid method, Dr Starfield has indeed rendered a valuable service to the mining industry. One could consider further instances of heat flow in airways in which the availability of a rapid computer method would be desirable, e.g. the flow of air down a shaft, where there is an increase in temperature due to adiabatic compression, as well as an increase in virgin rock temperature as the depth increases. However, this particular case would not present any new problems and would merely require an extension of the exisitng work. I should like in this contribution to talk about an aspect of environmental control in mines which, I think, will become more important in the future. It is well known that wet bulb temperatures are subject to fluctuations underground. In some instances, particularly in stopes, the fluctuations, both with time and position, can be considerable. The theoretical work which has been carried out on temperature increases has been aimed at the prediction of mean temperatures, and no account has been taken of fluctuations around this mean. It is questionable whether this approach will, on its own, be sufficient, particularly when temperature increases in stopes are considered. The fluctuations in air temperatures underground arise from two causes. The first of these would be the fluctuations in surface conditions, and here one could list random, diurnal and seasonal fluctuations. The second cause is the multitude of things which vary in a mine and here one could list variations in air flow quantity, sources of evaporation, heat transfer from pump and compressed air columns and, particularly in the stope, variations in air flow patterns. Fluctuations arising from surface temperature variations should be amenable to calculation, and here one envisages figures relating the decay of temperature variation with distance to factors such as air flow quantity. Fluctuations resulting from changes in the mine are perhaps more difficult to tackle theoretically and the best approach could well be to analyse underground observations. In this connection, there is a good case to be made for the increased use of statistical methods in the analysis of underground temperature measurements, and it might be of value to look at current air-conditioning practice. When carrying out cooling load calculations for a particular location it is customary to use design wet bulb

Jan 11, 1969

By C. F. Gleeson

"I HAVE BEEN ASSIGNED the pleasant task of adding a last word in way of summary to this session. I think that the trend set in having a geochemical session at the CIM Annual General Meeting is a good one and I hope it will continue so that members of the mining fraternity can get together on a regular basis and discuss geochemical problems peculiar to our Canadian scene. A series of interesting papers have been presented on what has been considered by many in the past as not only a problem area for geochemistry but even an impossible one. The papers should help dispel some of these fears. Lack of development of geochemical techniques in the Shield has been due to a variety of factors, many of which have been mentioned. However, I feel that one of the main reasons for this lack of development has been timidness on behalf of many people to get out and do the necessary work which helps produce answers to many of the questions asked. New developments and applications of geochemical methods in the Shield will not be done by the faint of heart but by those who have the curiosity, interest, imagination, drive, resources and, most of all, the intestinal fortitude to stick to it and not give up because results or conditions do not meet with preconceived notions. Another element that will be needed by those who will successfully apply the techniques and who will be responsible for new breakthroughs is the systematic approach to sampling and analysis and the integration of geochemical, geological and geophysical results. Erratic sampling patterns - a sample here and a sample there - generally lead to more problems than solutions."

Jan 1, 1971

By A. B. Irwin

"Discussion at MeetingDR. D. DERRY (Ventures Limited) referring to the diagram (Figure 15) which shows a transverse structure section across the Central Slocan area, asked what the assumed structure at depth was, remarking that dips are steeper and more uniform at depth and that the contortions with gently-dipping axial planes are at higher elevations. He wondered whether the section represented ,part of a very large fold with steeply-dipping axial plane.MR. J. D. LITTLE (Canadian Exploration, Limited) replied that E. B. Mayo (Kelowna Exploration Company) and others had considered that the entire section illustrated faces to the southwest and represents part of the lower limb of a great overturned •syncline which is concave toward the southwest.DR. R. DEWIT (Geological Survey) remarked that the photograph of a ripple mark (Figure 7) showed internal lamination conformable to the ripple mark and wondered if the structure was not due to slumping during consolidation, since the normal mode of formation of ripple mark would seem to preclude the possibility of such internal stratification.MR. LITTLE remarked that in his opinion such structures should not be depended upon alone with-out other confirmatory evidence of the direction of tops of beds."

Jan 1, 1952

By T. K. McMahon

Formally, a mathematical model could be defined as: A set of equations whose solution will approximate the response of a physical process or system to a set of stimuli which appear as parameters in the equations. The purpose of a mathematical model is to permit the rationalization of experience to proceed by simulation rather than by physical experimentation. In the application of digital computer control to an industrial process, the mathematical model of the process (subsequently called the process model) is needed to calculate the present process performance from the measured variables and to predict the response of the process to a control change. Functionally, the cardinal element in process model development is a concise set of control objectives. These, besides implicitly defining the boundaries of the system to be modeled, will determine the accuracy demanded of the model its nature: dynamic or steady-state, and so forth, The objectives should explicitly define what process efficiencies, production rates, qualities are to lie within the scope of the computer control project, thereby providing a basis for simplifying assumptions in the development of the model. This requirement, a limited set of control objectives, is so often disregarded in formulating industrial control problems that its repetition can scarcely be avoided.

Jan 1, 1965

By AIME AIME

ANNOUNCEMENT on August 6 of the historic event of dropping an atomic bomb on Hiroshima, Japan, was more dramatic even than V-E day, since that had so long been forecast whereas the bomb production had been the best-kept secret of the war, even though at one time more than 100,000 people had been at work in connection with its production, and some two billion dollars had been spent on the project. Mining men had long been aware of an unexplained abnormal interest in uranium production, and suspected that something of the sort was on foot, while metallurgists were aware that various men of their acquaintance were engaged in some top secret research. The first announcement was soon supplemented by other official releases which told more about the research laboratories for theoretical and pilot studies, and the plants in Tennessee and Washington, but none of them made clear what the modus operandi is of these terrific bombs. Inquiry at Colum. bia University, where Dr. Dunning and his associates had succeeded in 1939 in splitting the uranium atom, and where laboratories known only as SAM have been feverishly active since the beginning of the war, was unproductive, since none of those officially connected with the project could give out anything beyond the official releases.

Jan 1, 1945

By C. W. Arnold, H. L. Stone, D. L. Luffel

The purpose of this research is to determine (I) the efficiency of small banks of enriched gar driven by methane in displacing oil from a porous medium and (2) the effects of variation in bank size and composition of that efficiency. Most of the experiments were conducted in a sand-packed tube 20-ft long and 1/2-in. in diameter. The hydrocarbon system generally used was methane, butane and decane at 2,500 psia and 160°F. The results of these experiments indicate that, in the regions contacted by the gas, a small bank of an oil-miscible gas driven by methane can displace all of the oil in a piston-like manner. If the enriched gas is of such composition as to remain immiscible with the oil, displacement of oil is less efficient than for the miscible case, and the gas bank travels through the sand with a velocity less than that of the driving gas. These data along with theories discussed imply that smaller banks and less total gas are required when the enriched gas and oil are miscible. INTRODUCTION Widespread application of enriched-gas drive to the recovery of oil rests upon a key factor — the use of limited quantities, or "banks", of enriched gas. At the present time, the value of liquefied petroleum gas or other enriching agents discourages their use in a continuous injection technique, or even in a large bank, except in a few isolated reservoirs. If small banks of enriched gas driven by methane were as effective in displacing oil as is continuous injection, the enriched-gas drive process might be applied to a larger number of reservoirs. Previous research on the mechanics of the enriched-gas drive process reported by Stone and Crurnpl and by Kehn, Pyndus and Gaskell has utilized continuous injection of enriched gas. This work has shown that two types of displacements occur. With gases containing sufficient intermediates. the oil is displaced misciblv and complete recovery is obtained from the regions swept. When gases are used which contain insufficient intermediate hydrocarbon for miscible displacement, oil is displaced immiscibly. In the latter type, selective solution of the intermediate hydrocarbons causes a swelling and reduction in viscosity of the oil and leads to an increased recovery over that obtained by dry-gas (methane) drive. The size of the enriched-gas bank necessary for efficient displacement of oil is determined by those factors which cause deterioration of the bank. A differentiation may be made between those factors which operate on a microscopic scale and those which act on a macroscopic scale. On the smaller scale, the enriched gas mixes in the direction of flow by diffusion and convection with the fluids immediately preceding and following it. On the larger scale, the gas may by-pass the oil by flowing through permeable streaks, by overriding the oil because of density difference, or by fingering because of unfavorable viscosity ratios. In such cases, the enriching material tends to mix with the oil both laterally and in the direction of flow. The increase in effective area available for diffusion and dispersion of the enriching components leads to a faster degradation of the bank and a need for a larger bank than is necessary for those cases in which no by-passing occurs. The effects of such macroscopic factors in the deterioration of enriched-gas banks have been reported in a separate paper by Blackwell, Terry and Rayne. The present study was confined to the factors which operate on the smaller scale, in particular to the behavior of banks of enriched gas in sands uniformly swept by the gas. Experiments were designed to answer the following questions. 1. Can small banks of enriched gas driven by methane be used to secure oil recoveries comparable to those obtained by continuous injection of enriched gas? 2. What is the optimum bank size (the minimum bank size necessary to obtain a recovery comparable to that obtained by continuous injection of the same enriched gas)? 3. How many total pore volumes of gas must be injected to obtain the maximum recovery when the optimum bank size is used? 4. What is the effect of varying the number of enriching components in a gas bank? This report describes the experimental investigations and discusses the results in terms of their significance to reservoir behavior.

By Felix E. Wormser

REGISTRATION started bright and early Monday morning in the Silver Corridor at the Waldorf-Astoria with Mrs. W. H. Bassett as chairman. What a registration-over 200 ladies! Several joined us from as far away as California and Washington State. Apparently they enjoy our meetings so much that present travel inconveniences didn't discourage their coming. At noon the ladies joined the men at the All-Institute Luncheon and Monday evening we had our informal dance, which is separately reported. Tuesday morning was devoted to our annual meeting at which all Section annual reports were read. At noon we were all the guests of the W.A.A.I.M.E. at a luncheon at the Port Arthur Restaurant on Mott St. in Chinatown. Many of us rode down on the old 3d Ave. elevated railway-the last of four. It, too, is soon to be torn down. The luncheon was delightfully unusual, with huge dishes of delicious Chinese food on each table. Our chairman, Mrs. Read, who lived in China in her youth chose our menu, and she chose it well, for most of us indulged so heartily that as we arose from the table we felt we couldn't eat again for 24 hours. Someone donated sherry wine, and boxes of Chinese pencils as favors. We wonder who? All owe a big vote of thanks for this lovely party to Mrs. T. T. Read and Mrs. H. A. Prosser, chairmen, and Mrs. H. W. Hardinge, Mrs. R. Hursh, and Mrs. R. L. Lloyd, vice-chairmen.

Jan 1, 1944

By AIME AIME

L. C. GRATON, professor of geology in Harvard University, addressed the New York Section on April 24 on-his impressions of the Rand. His beautifully clear and concise address was delivered without notes, so that what follows is merely a resume of the principal points made. The world is apparently coming to the end of ore discoveries easily made, yet we need metals at a steadily increasing rate. If surface discoveries are to decline, then we must find other ores or use less metals. The probable chances of finding ore are greater in the centers of big production than in new districts, as proved statistically. It is unsafe to say that a field is worked out. Therefore, deep mining holds possibilities and is an interesting study that will progressively gain in importance. The origin of the gold in the banket of the Rand has been a geologic football for a long time. Of the various theories, two have survived: 1. Infiltration into permeable conglomerate beds from deep-seated sources; 2. the placer hypothesis, which holds that gravel beds originally had the gold in them. At present, the second theory is accepted by the majority, as a result of the studies by the Union Geological Survey and by E: F. Mellor which were published about fifteen years ago.

Jan 1, 1929

By K. Harms, T. D. Jones

TO unload large tonnages of lead bullion cast in 100-lb. bars is a problem which has confronted the lead refineries for many years. The bars, on arrival, must be restacked for unloading by truck or hand-charged to charging machines. Selected crews of labor, capable of working at sustained speeds for five- or six-hour periods, are required for this exhausting task. Due to the fatigue involved crew personnel changes rapidly. During the war it became increasingly difficult to maintain crews, especially in critical labor areas, so that the development of casting and shipping ten-ton lead blocks from the smelters to the refineries became a must in our operating program. For many years lead refineries, when making interdepartment or intradepartment transfers, have cast lead blocks weighing five or ten tons which are easily handled by crane by merely attaching the crane hook to a steel anchor embedded in the frozen lead blocks. In previous years, the practice was to use regular smelter slag pots which, due to their rounded shape, produced what were called "buttons" by the refinery personnel. The button-type blocks were unsafe as they rolled and tipped easily and were unsatisfactory for stacking since no piling pattern could be followed. To remedy this situation, flat-bottom molds came into general use and later the bottoms were made concave to prevent slipping.

Jan 1, 1946

By James R. Stuart

AS the available remaining properties of iron ore reserves on the Mesabi Range are opened up for mining, the various properties located under lake beds are brought nearer an active status. The actual physical problems involved in stripping these properties do not act as a deterrent so much as the legal and political problems that are encountered. When it is proposed to destroy a natural lake that has been used by the public for many years, much local as well as state opposition may be encountered regarding its destruction. Public hearings must be held and some adverse publicity is likely to result. The ownership of the ore under the lake and the rights of the abutting property owners must be settled, and protection from damage caused by a disturbance in surface and subsurface drainage is likely to be demanded by property owners some distance from the proposed mine area. The Embarrass Mine, located near Biwabik, Minn., falls into this classification. A portion of the orebody lies under what was formerly Syracuse Lake, this body of water having been removed in the process of stripping the mine. An additional problem in the case of a meandered body of water is the establishment of a meander line that can be projected downward as mining progresses to form the basis for a satisfactory division between lake bed and upland ore shipments for royalty purposes. Fig. 1 illustrates the complications encountered in maintaining these divisions. A balance point was agreed upon in the center of the lake to make an equable division of lake bed ore to the abutting properties. The entire lake bed has since been adjudged the property of Minnesota. Lake Characteristics Lake bed stripping problems with which this paper is concerned necessarily are limited to a specific type of lake, namely the glacial lakes of the Lake Superior region. One characteristic common to these bodies of water is a deposit of fine black mud or silt on the bottom, frequently underlain by a layer of impervious blue clay. This is also true of the muskeg areas of the region, which present almost identical problems as lakes in stripping. The actual removal of the water and the lake bed material is a routine matter more or less standardized as to equipment, and the period of time required can be estimated easily on the basis of volume and capacity. More important than the foregoing is the execution of preliminary work, and above all, the timing involved. An account could be prepared based entirely on statistical and cost data which would give a very fair picture of the time required and cash outlay needed to effect the removal of a body of water preliminary to stripping the orebody. However, the real interest from the standpoint of the operator and the engineer who carry responsibility for completion of the job lies in the unexpected emergencies and the action of various materials involved in the stripping when the balance has been upset through diversion of water courses and the reduction of the lake level. Runoff and Drainage Lakes are located in natural basins that catch all the rain water and runoff water for a considerable area. Where a lake is involved having an inlet and outlet or a sizeable water course running through it, the drainage area may include a watershed covering many square miles. All available data then must be collected to supply a history extending over as many years for which information can be gathered on the flow of streams, annual rain and snowfall, and most important, the peak flows to be expected. Where the diversion of a stream around the stripping area is a part of the problem, this last factor is of great importance since it controls the cross-section to be selected for the diversion channel and the volume to be removed in its excavation, as well as affecting the hydraulic considerations to be met in the design of the completed channel. Characteristic material in the overburden found at the Embarrass Mine is illustrated in Fig. 2. Well Pumping Pumping from the well holes was started well in advance of the draining of the lake. Fig. 3 shows a gradual lowering of the water table with no noticeable fluctuations during the period in which the lake was being dewatered. Unfortunately, because of tight ground, a maximum flow to the wells was not maintained. This retarded the rate at which the water table was reduced so that in the course of stripping the excavation soon extended below the water table, and the great bulk of the pumping was handled from a system of sumps in the pit itself. Any dewatering program projected by prepumping from wells, a glorified well point system, would have to be started well in advance of the stripping to be of any great advantage. Preliminary drainage of the surface over the mine area is entirely apart from the actual elimination of the lake bed itself. Since the lake is what is called a perched water table because of the impervious character of the lake bottom, the adjoining surface may be dewatered below the surface of the existing lake and the flow will not be affected by the proximity of that body of water. This condition actually has been demonstrated through the establishment of a number of observation holes where a small churn drill was used to put down the holes and a 3-in. pipe was installed for taking water level

Jan 1, 1952

G. A. Burr, Parral, Chihuahua, Mexico (communication to the Secretaryt): I regret that Mr. Norris did not give more attention to the hoisting of water in inclined shafts or slopes: the only slope mentioned being Hickory Ridge Slope, No. 4, of the Union Coal Co. The surface arrangement, illustrated in Fig. 12 of his paper, if not unpractical, is at least unscientific and cumbersome. It is my opinion that the back- and sideguides shown in Fig. 12 are not only unnecessary where rails are used as a track, but are unsafe, excepting in the case of a very firm hanging-wall, or roof, and sides of vein-matter, having absolutely no tendency, either to settle from the back, or to squeeze from the sides, an effect which would inevitably force the guides out of alignment. The accompanying illustration, Fig. 1, shows what I consider a better method of hoisting water than that described by Mr. Norris. This method is based on the general practice in metalliferous mines of the West, where skips are used in slopes; and, while it is not original with me, I have frequently used it with very satisfactory results for dumping both ore and water.

Jan 1, 1904

By J. E. Johnson

Discussion of the paper of Bradley Stoughton, presented at the Cleveland meeting, October, 1912, and printed in Bulletin No. 71, November, 1912, pp. 1245 to 1275. J. E. JOHNSON, JR., Ashland, Wis. :-Is it true that titanium reduces the chill in chilling iron? If so, as I think Mr. Stoughton has stated elsewhere, then I do not see how titanium is beneficial in car-wheel mixtures. One of the most difficult things to do is to get a proper chill and a proper degree of toughness, and the goodness of an iron of the given composition for charcoal-iron purposes is denoted by the chill which it will take as compared with its composition. If titanium reduces that chill, then it does not seem to me as good for car-wheels as its absence would be, and I should like to have it explained what effect titanium has on the chill of a given iron. MR. STOUGHTON : It is true that titanium reduces the chill of iron quite noticeably, yet, at the same time, if I am correctly informed, 90 per cent. of all chilled-iron rolls are made to-day with the titanium treatment, and a great many car-wheels, but one has to make changes in the silicon added and also, if I am correctly informed, in the manganese. The advantage of titanium is that when the proper changes are made, so that we get the same depth of chill with the titanium as we otherwise would without, the chill is much harder than before, and also the body of the roll or wheel is tougher and somewhat stronger, especially under shock. JAMES F. KEMP, New York, N. Y.:-This subject is obviously one of great importance to the iron industry, in that if we call find a method of using titaniferous ores, we will prolong the life of our iron reserves. Fifteen or more years ago, primarily from the study of the ores in the Adirondacks, I be-

Dec 1, 1912

By Robin Phinney

Certain statements in this presentation may constitute "forward-looking" statements which involve known and unknown risks, uncertainties and other factors which may cause the actual results, pe1formance or achievements of the Corporation, or industry results, to be materially different from any future results, performance or achievements expressed or implied by such forward-looking statements. When used in this presentation, such statements use such words as "may", "would", "could", "will", "intend", "expect", "believe", "plan", "anticipate", "estimate" and other similar terminology. These statements reflect the Corporation's current expectations regarding future events and operating performance and speak only as of the date of this presentation. Forward-looking statements involve significant risks and uncertainties, should not be read as guarantees of future performance or results, and will not necessa1ily be accurate indications of whether or not such results will be achieved. A number of factors could cause actual results to differ materially from the results discussed in the forward looking statements including, but not limited to, the factors discussed in the Corporation's annual information form filed on March 9, 2011. Actual results could differ materially from those currently anticipated due to a number of factors and risks. These include, but are not limited to, the failure to obtain necessary regulatory approvals, including environmental approval, the failure to secure full project financing, the failure to implement the recommendations set out in the Technical Report, the failure to raise financing to implement the recommendations in the Technical Report, risks associated with the mining industry in general (e.g., operational risks in development, exploration and production; delays or changes in plans with respect to exploration or development projects or capital expenditures; the uncertainty of estimates and projections relating to production, reserves and resources, costs and expenses; and health, safety and environmental risks), decrease in potash prices and exchange rate fluctuations. Although the forward-looking statements contained in this presentation are based upon what management of the Corporation believes are reasonable assumptions, the Corporation cannot assure shareholders that actual results will be consistent with these fonvard-looking statements. These fon\?ard-looking statements are made as of the date of this presentation and are expressly qualified in their entirety by this cautionary statement. Subject to applicable securities laws, the Corporation assumes no obligation to update or revise them to reflect new events or circumstances. This presentation is a market update based on the Corporation's public disclosure and does not form a part of any offer of securities, or constitute a solicitation of any offer to purchase or subscribe for securities. Any purchase of securities in the company should be made solely on the basis of information contained in the Corporation's public record which is available on www.sedar.com .

May 1, 2013

By M Alston

Organisations’ incident classification processes are plagued by the overclassification of events, often leading to excessive workloads and suboptimal outcomes. This presentation addresses the pressing need to rethink how incidents are classified to maximise organisational learning and minimise systemic risk. A major issue in the current incident classification landscape is the tendency to classify events at high levels, overwhelming organisations with investigations they cannot efficiently handle. This results in inadequate risk reduction and learning opportunities. The link between injury classification and investigation methods further compounds these problems, creating unnecessary administrative clutter. Challenging the misconception that every event, no matter how minor, requires a comprehensive investigation, this presentation advocates for a shift in perspective. The key recommendation is to decouple injury classification and risk matrices from the decision-making process regarding what and how to investigate. Instead, the emphasis should be placed on identifying opportunities for organisational learning and risk reduction. Organisations can streamline their incident management processes by adopting a more pragmatic approach that aligns incident classification with the organisation’s investigation capacity. This transformation focuses on achieving meaningful outcomes, enhancing safety and improving performance. This presentation provides an innovative process for organisations to revamp their incident classification practices, enabling them to harness the full potential of incident data for learning and risk mitigation. It highlights the importance of aligning incident classification with the opportunity for organisational learning, ultimately leading to more effective incident management and enhanced safety outcomes.

Apr 16, 2024

By W. A. Klikoff, I. Fatt

The concept of fractional wet wattability is examined. Fractional water wettability of a reservoir rock is defined as the fraction of the internal surface urea that is in contact with water. Capillary pressure and relalive permeability of unconsolidated sand are shown to be functions of fractional wettability. INTRODUCTION The petroleum industry has long recognized that wettability of reservoir rock has an important effect on multiphase flow of oil, water and gas through reservoirs. As early as 1928 the American Petroleum Institute sponsored a study of wettability as part of API Project 27 at the U. of Michigan.' Despite 30 years of research, there is still little exact knowledge of the wettability of reservoir rocks. There are two parts to the wettability problem. After agreeing to a uniform nomenclature in regard to wettability,' the first question to be answered is, "What is the in situ wettability of a given reservoir rock?" If this can he answered the next question is, "What part does wettability play in determining the characteristics of multiphase fluid flow through the rock?" This paper represents an oblique attack on the problem of wettability. No attempt is made here to answer the basic question of wettability in situ. instead the consequences of the concept of fractional wettability are examined. Multiphase flow in sandpacks is shown to he highly influenced by fractional wettability. Jennings' has given 3 definition of wettability and the other terms used in discussing wettability. These terms must be applied to the physical situation existing In reservoir rock. A survey of the pertinent literature from 1928 to 1956 indicates that the concept of a contact angle was applied to reservoir rock in the same way it would be applied to a flat, homogeneous surface. Attempts were made to state quantitatively the wettability of a reservoir rock in terms of a contact angle which was presumably constant at all points on the very rough and heterogeneous interior surface of a porous rock. Calhoun, et al,3-6 prepared synthetic consolidated and un-consolidated porous media in which they claimed there was a known uniform contact angle. They then showed the effects on the capillary pressure and relative permeability characteristics of varying this angle. The API Project 47 at the U. of Texas' and others' have made extensive studies of an indirect approach to the contact angle through the use of heat of wetting data. Even if successful. however, this approach also states the wettability of porous rock in terms of a contact angle which is uniform over the entirc surface. If the angle varies from one part to another on the internal surface, there is no way of determining from the measurements the area distribution of contact angles. In 1956 Brown and Fatt5 suggested that the concept of a contact angle, as applied to reservoir rock, be abandoned. This suggestion was made because it is known that the internal surface of most reservoir rocks is composed of many different minerals, cach with a different surface chemistry and a different capacity to adsorh surface active materials from reservoir fluids. Furthermore, the operation of a contact angle in determining the form of a fluid-fluid interface is difficult to picture in the very complex geometry of a pore. Brown and Fatt proposed that the wettability of reservoir rock be stated in terms of the fractional internal surface area that is in contact with water or oil. All surfaces on which there is water are called water-wet; surfaces on which there is oil are called oil-wet. The fractional water wettability is then stated as a number which represents the fraction of the internal surface that is in contact with water. A symmetrical statement can be made for the fractional oil wettability. The concept of a fractional wettability as previously stated has in its favor the recognition of the heterogeneous mineral composition of most reservoir rocks. Another point in its favor is that fractional wettability can be measured quantitatively with relative ease. Hol-brook and Bernard10 se a simple dye adsorption test to obtain fractional wettability of reservoir rocks. Amott11 uses a combination of imbibition and displacement to arrive at a wettability index of reservoir rocks which seems related to fractional wettability in the range 0.25 to 0.75 fractional water wettability. Jennings" has shown the changes in relative permeability that take place when a porous material is changed from unity to zero fractional water wettability. He also shows that reservoir rocks in their natural state, but at room temperature and atmospheric pressure, have relative permeability characteristics which would indi-