Search Documents

Many studies have been conducted over the past 3 decades on the leaching of gold in solutions containing thiosulfate, ammonia and copper. However, most of these studies have been carried out using ore samples, with very few fundamental studies of this system being attempted. The majority of the published studies have failed to acknowledge the undesirable side reaction between copper(H) and thiosulfate, let alone account for its effect. The fact that the solution chemistry is constantly changing makes it very difficult to perform a fundamental study of gold leaching. With the advent of the rotating electrochemical quartz crystal microbalance (REQCM), such fundamental studies are possible as this instrument measures mass in real time. This has allowed leach kinetics to be measured in a matter of minutes and hence at essentially constant solution conditions; The present paper highlights that a sufficient concentration of copper(II) and ammonia are required in order to achieve appreciable gold leach rates. However, the use of air (oxygen) to maintain the copper(Il) concentration catalyses the undesirable copper(II) reaction with thiosulfate. The presence of ammonium ions is shown to have an effect on this undesirable reaction as well as on the gold leaching ?reaction. Preliminary electrochemical studies into .gold electrowinning using the REQCM show that gold(I) thiosulfate cannot be readily reduced to metallic gold in the potential region at which cementation usually occurs. However, it is well known that gold cementation onto copper occurs rapidly. The current study addresses this discrepancy by studying the effect that copper and silver have on the reduction of gold thiosulfate. It has been found that the presence of both silver and copper enhance gold deposition, particularly at low over potentials. While this is beneficial in cementation, the presence of copper and silver in solution has been found to cause passivation of the cathode surface during electrowinning at 'higher overpotentials.

Jan 1, 1998

By T. L. Tanton

Introduction Sturgeon River area, on the east side of lake Nipigon, Ontario, was the scene of a gold rush in 1934. According to press reports, the active staking during the latter part of the summer spread out rapidly from the early holdings until it embraced practically all of the lower basin of Sturgeon river in a belt up to ten miles wide extending west from Kinghorn for 35 miles to lake Nipigon. And, before winter set in, active prospecting and claim staking reached beyond lake Nipigon to areas where belts of ancient schists were known, notably west of Obonga lake. The writer's familiarity in past years with the areas to which attention has been directed admits of some observations on means of access in the field, the general geology, and the progress that has been made in identifying formations favourable for the occurrence of gold. Canoe Routes From the writer's observations in Sturgeon River area in 1917 and in the Obonga Lake area in 1933, it is recalled that there is, locally, a striking dif~ ference in the accessibility of the two areas by travel along canoe routes. Sturgeon River area is easily accessible from Kinghorn or Jellicoe stations on the Canadian National railways. Many small lakes, commonly of the linear type and with elongations east and west, occur among the forested rocky ridges near Jellicoe (Figure 1) and to the east and west along, or adjacent to, Sturgeon river. This stream has long stretches with gentle current between the falls and rapids. The drainage system provides excellent canoe routes (Figure 2), and the interruptions to travel (Figure 3) are remembered .as scenic features that were passed by portages with firm footing. West of Obonga lake, the streams flowing easterly to lake Nipigon may be followed through scenic canyons to a plateau of law relief characterized by extensive muskegs and shallow, brown-water lakes; and along small streams, where beaver dams have been destroyed, there are muck ponds where the usual alternatives of paddling or portaging can be dismissed in favour of the 'moosing' method of progress with the canoe (Figure 4).

Jan 1, 1935

By M J. Noy

The automated measurement of rock fragmentation particle size distribution in the muck during muck excavation has been developing over the last 16 years. The introduction of stereo camera imaging of the muck has provided improved automated particle segmentation for image-based measurement algorithms. Recently, a new vision system processing algorithm has been developed. The inclusion of 2D texture in the analysis has provided a significant improvement in the definition of the finer size fractions, which has resulted in the automated analysis no longer requiring calibration.The previous stereo vision system algorithm required analysis calibration to account for poor ‘small particle’ definition in the 3D surface profile. This was because of the depth perception limitations of the stereo camera system at greater than 8 m. The new algorithm has been implemented on a number of shovel-installed vision systems, and the algorithm’s performance in automated analysis has been assessed against a diligent manual analysis of the same fragmentation images. The new algorithm provides improved distribution resolution and accuracy.CITATION:Noy, M J, 2015. Evaluation of a new vision system algorithm for automated fragmentation measurement from a shovel, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 721–726 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By T. Matthews

"One critical factor in mineral reserves reporting, as well as mine-reserves reconciliation, is the impact of dilution and ore loss in the mining process. This paper considers the implications of various factors on dilution and ore loss projections, by orebody geometry, mining method, and ore control systems. We also discuss the implications of resource estimation methodology on dilution for reserves. DEFINITIONS Dilution and ore loss are two critical concepts in mining, which address the differences encountered between modeled grade and tonnages and actual production. Dilution is volume increase and grade reduction caused by multiple factors, chief among which are mining of waste material along ore-waste contacts, mining of internal waste as ore, and misclassification of waste as ore in the ore control process. There are also geostatistical and estimation aspects sometimes lumped with dilution, including the volume-variance effect (the tendency for small volumes of material to include a less regular distribution of grade than large volumes of material). Ore loss is described as reductions of ore volumes in the mining process due to misclassification of ore as waste in the ore control process, exclusion of discontinuous mineralization from mining due to geometry or continuity, and mechanical losses in the mining process. Dilution is typically taken as an increase in tonnes of ore with no change in contained metal (and thus results in a reduction in grade.) (Some workers consider the likely grade of the diluting material as well, particularly in deposits with gradational grade boundaries—this will be addressed later in the text.) Ore loss is typically taken as a reduction in tonnes at average grade of the ore, and thus results in a reduction in both tonnes and contained metal. If model (resource) tonnes are Mt, grade is Mg, and contained metal is Mm, the resource with ore loss (L) and dilution (D) included (Rt, Rg, and Rm) will be:"

Jan 1, 2015

By A. L. Mular

"This paper summarizes the present-day usage of computers in the mining-metallurgical industry. The industry appears to be following a path taken by other industries in improving the operation of processing plants, production schedules, grade control and haulage performance. A reduction in the cost of computers and computing has been a significant factor.An attempt is made to forecast the future of computers in our industry. Such developments as time-sharing, mini-computers, and easy-to-understand process-oriented languages will lead to wider usage. Considerable strides have been made in the use of computers for laboratory data acquisition. In general, the implementation of new methods, new techniques and new equipment will require plant personnel to develop new skills. The universities are meeting this challenge by re-structuring curricula and offering special courses. Most vendors of computers already offer special courses within their own facilities at a customer's plant."

Jan 1, 1970

By Edward H. Eisenbrey

This paper is primarily concerned with the exploration for massive sulphide orebodies. In a discussion of this type, it seems appropriate to establish a few definitions so that all parties may consider the same beast and its habitat. First, the term "massive sulphides", as used here, not only denotes a body of mineralized rock containing in excess of 50% sulphides by volume, but a mass of sulphides that respond as a conductor to the electromagnetic (EM) systems currently in use in exploration. "Disseminated sulphides" refer to all of those sulphide occurrences that respond to the Induced Polarization (IP) geophysical methods most commonly in use in porphyry copper exploration. This latter definition may also include the disseminated sulphide halos so frequently found associated with massive mineralization as well as banded and stringer sulphide mineralization. It is plain to see that these two end members of our definitions can easily blend into each other. The term "volcanogenic" refers here to any and all geologic processes that have their origin in volcanic activity. Thus we are concerned here with the exploration for massive sulphide ore deposits derived from and affected by contemporaneous and post mineral volcanic activity. Furthermore, most massive sulphide deposits are apparently formed in a submarine environment, deposited with extrusive rocks and sediments and/or chemical hot spring accumulations, then enclosed and protected by the addition of more volcanic and sedimentary material then, probably folded and deformed into one of their myriad of shapes.

Jan 1, 1973

By R. W. Stahl

A survey of firefighting facilities and practices in coal mines conducted by the Bureau of Mines3/ showed such variations in equipment and apparent attitude toward fire protection that a comparison with other industry seemed advisable. Although other industry is confined generally to surface operations and the hazards probably are not as great, the same general methods of extinguishment are employed, so that the cost and protection at least should be comparable. An investigation of industry other than mines revealed a generally greater emphasis placed on fire-combating equipment, fire-brigade training, fire-fighting facility inspection, and fire-hazard elimination, as well as a greater average expenditure for fire protection.

Jan 1, 1959

By C. Abbruzzese, F. Vegliò, S. Ubaldini, R. Massidda

"Gold solubilised during cyanidation can be recovered by precipitation (Merrill-Crow process) or by adsorption onto activated carbon, these being the techniques applied in industrial plants.Precious metals (Au, Ag) adsorbed onto activated carbon are extracted during a subsequent stage in aqueous phase, by various technologies, such as hot elution (70-80°C) or under pression desorption (100-130°), with hydro-alcoholic solutions.This stage is of great interest from an economic point of view, due to the high energy costs. Temperature represents the critical kinetic factor.The aim of this paper was to study the influence of different water/organic solvent mixtures (isopropyl alcohol, ethanol and ethylene glycol) on the desorption process.The experimental work was carried out on laboratory scale, using activated coconut carbon with different temperatures and extraction times, without adding cyanide.Best results have been obtained in this order: isopropyl alcohol > ethylene glycol > ethanol. Starting from gold concentration of about 5 g Au per kg of carbon, best kinetics resulted in 97-100% of gold extraction, after 8 hours of desorption, at a temperature of 80ºC."

Jan 1, 2003

By Bill Birch, Toby White, Ian Brown

costs/benefits of electronic detonators and measure their effects on primary crusher productivity. 9 blasts (3 shock tube blasts, 6 electronic blasts). Measured electricity consumption & primary crusher throughput. Change to Electronic Detonators resulted in a 7% reduction in primary electricity costs and a 15% increase in primary crusher productivity.

Feb 1, 2020

By Leslie C. Richards

The competitive position of producers of industrial minerals depends upon the delivered price of their product. Freight charges are a major factor in the sales to consumers. A comparison of freight rates on movements of limestone and silica rock in the Pacific Northwest shows a wide variance in mills per ton mile for like hauls, thereby favoring some localities over others.

Jan 1, 1950

By Kalervo Rankama

UNTIL a few years ago, geological mapping, the study of ore boulders, and different geophysical methods were the principal means used in the systematic search for mineral deposits covered by a layer of disintegration products or soil. These methods have been developed to a high stage of perfection as far as the geometrical definition of the conductor is considered. Use of geophysical methods in prospecting is based on the fact that an ore body differs from the country rock not only geologically but also in its physical properties. The general drawbacks and complications included in the use of geophysical methods are well known to everyone who has been using them, so need not be entered into here in detail. One of the more important ones is the fact that geophysical methods are unable to furnish information concerning the chemical composition of the ore bodies responsible for the indications. Further, the ores of many metals, such as silver, gold, beryllium, zinc, mercury, tin, lead, vanadium, antimony, chromium. molybdenum, tungsten, manganese, cobalt, nickel, and the platinum metals cannot be directly located by known geophysical methods, owing to lack of physical characteristics suitable for distinguishing them from the country rock. Thus it is quite natural that efforts have been made to develop direct methods for prospecting and locating ore bodies of the elements named. Known as chemical, biogeo-chemical, and geobotanical methods of prospecting, these have been much improved during recent years. A brief review of these methods and of some results obtained with them will be presented in the following, on the basis of available information and my own experience.

Jan 1, 1947

By Brandon Smith, William Bohlen

Riverbank erosion along the Brazos River has modified the structural support conditions for an existing bridge structure in Southeast Texas. The 8-span, 1,200-foot long bridge was completed in 1992 along Highway 99, a key corridor for the Houston area. Foundation support conditions have been altered due to natural, ongoing river morphology for three bents on the affected riverbank. Recent events include three storms within a three-year period that each exceeded the 500-year return probability. This resulted in accelerated erosion along the northern riverbank. Over forty vertical feet of soil has been removed in some locations. Drilled shaft foundations are now functioning as columns. This review considers the behavior of columns and deep foundation elements due to the modified support conditions. The review ultimately presents a rational methodology for the review of the present and anticipated future bridge configuration with respect to current strength, service, and extreme event limits, with corresponding safety factors for the design. Introduction and Background The Fort Bend Grand Parkway Toll Road Authority (Owner) oversees the State Highway 99 Judge Jodie Stavinoha Bridge over the Brazos River. The 8-span, 1,200-foot long bridge was originally designed with four southern approach spans of 115 feet; a three-span continuous river crossing with span lengths of 195 feet-235 feet-195 feet; and a single northern approach span of 115 feet. Figure 1 provides an overview of the northern portion of the bridge. Table 1 provides a summary of the original bridge substructure configuration. When the bridge was completed, the centerline of the Brazos River was located at midpsan of the main span and the northern high bank was originally located at Bent 7. Erosion process has forced the northern high bank to Abutment 9 (also called Bent 9), and the river centerline during normal flow conditions is located south of Bent 8. The overall estimated river excursion at present day is approximately 270 feet to the north from its original location. An erosion wall that was installed in 2017 limits further erosion of the north river bank within the 300-foot width of the roadway corridor right-of-way. This study was developed to better understand the existing conditions, and to forecast the need, nature, and criteria for potential future improvements.

Jan 1, 2019

By Donald H. McLaughlin

THE activity and enthusiasm of pioneers still prevail among workers in applied geophysics1.- Within the year, new devices have .been tried out, instruments and technique have been improved and the methods of application to commercial problems have been increased in many ingenious ways. There is still great need for more skillful interpretation of results in terms of geology, but oil the whole geophysical prospecting is making encouraging progress toward finding its proper place and function in engineering and geological practice. Spectacular successes continue to be reported, particularly .from the Gulf Coast, where the race for salt domes has not slackened, and encouraging results have been giined elsewhere in the mapping of structures in the search for oil. In the mining field, however, it can hardly be claimed that the same measure of success has been obtained, for brilliant efforts worthy of wide recognition have been overshadowed to some eatent by the unfortunate outcome of surveys undertaken unwisely without recognition of the limitations of the work. Consequently, hopes were aroused that could not be fulfilled, and it must be admitted in an impartial survey that there are a few regions, chiefly in the far north, where the standing of geophysical prospecting is somewhat doubtful and where the course of public opinion regarding it shows a certain similarity to the history of the market during the past few months. Reliable work, however, is steadily going 011 and it can confidently be expected that the methods will eventually be regarded in many regions as an essential part of the technique of securing geologic data needed for intelligent exploration.

Jan 1, 1930

By Walter W. Bradley

FOR a number of years up to the economic setback of the 1929-1931 period, the greatest proportional advances in the mineral industries in California were made among the substances in the nonmetallic groupings, particularly among the so-called industrial minerals and the salines. During the past year or two, although these have not regained the stride that marked their progress in the preceding decade, we can still record, -some new developments. California produces annually between 55 and' 60 different minerals on a commercial scale. Of these, some 40 to 45 comprise the "structural," "industrial," and "salines" materials as grouped in the reports of the State's Division of Mines. Barite-The barite deposits of California were described in Report

Jan 1, 1935

By E. A. Anderson

THIS seems to be the year for superlatives in A.I.M.E. meetings. The programs of the various Divisions and Institute committees offered an abundance of interesting and valuable information in the form of technical papers, symposia. and lectures to large and interested audiences. The Institute of Metals Division may hold up its head with pride for its own program. With six technical sessions, three full-day symposia, and the annual I.M.D. dinner, four meeting days were not enough and many simultaneous sessions were required. The quantity and quality of the paper were equaled by the numbers and interest of those attending.

Jan 1, 1944

By D. R. Mitchell

MEETING for the thirteenth time in New York as part of the five-ring circus known as the Annual Meeting A.I.M.E., the Coal Division experienced a wartime boom in attendance. Technical sessions were crowded and whereas 65 seats were set up for the annual luncheon meeting of the Division over 100 members showed up, many of whom had to be fed elsewhere. Possibly the Coal Division should adopt "13" as its lucky number. Discussions at technical sessions, formal and informal, were lively. Those papers containing material directly concerned with the war, or containing information that might be usable for war industries, were enthusiastically received. Some criticism was made in regard to the present method of handling discussions and it was suggested that better success would be had in getting discussions in the record by the use of hired reporters. This is being considered by the executive committee of the Coal Division.

Jan 1, 1943

By Harry P. Hohenadel

DURING the past few years the amazing developments of the chemical industry have inspired so much publicity that the feature writers assure us that we are entering a "Chemical Age," industrially as important as the "Steel Age" and the "Electric Age," so-called. Whether or not these assurances are overstatements, it is a fact that the expansion of the chemical industry during the past 25 years has been enormous. The Chemical Bureau of the War Production Board calculates the value of chemicals produced during 1944 at $8,300,000,000, no small sum even in inflated dollars. As concerns us of the Southwest oil and gas country, four significant trends of the chemical industry are most important. (1) Many of the recently developed chemical products are new creations, not substitutes,. as new and original as the invention of the light bulb, and with a field for exploitation almost as wide. (2) Many of these chemical products will enter the mass consuming markets, which require enormous tonnages of products, and such markets are setting up an industrial demand for chemicals on a mass volume basis, compared to the relatively high-priced low-volume basis ordinarily considered as the chemical outlet of the past. (3) Most of the processes involved in producing these chemicals are adapt. able to the use, all or in part, of natural gas, oil, or refinery gases as raw mate-

Jan 1, 1945

By WILLIAM BOWIE

THE development of the isostatic idea during the last century would make an interesting paper in itself. But the various steps in the development have been covered in a number of papers and books which are readily available. Therefore this short paper should not give space to. the historical phases of the subject. Isostasy is really an old idea, but it is only in the last few decades that it has taken on any great prominence or importance in the study of earth phenomena. It is really remarkable how closely Dutton' sensed the isostatic principle 40 years or more ago. His general principles of isostasy as outlined by him have stood the test of time and fit in closely with the general ideas held today. It would seem, however, that some of his views with regard to the application of isostasy to geological processes must be modified or abandoned.

Jan 1, 1930

By AIME AIME

EVEN though most of the program of the joint meeting at Easton, Pa., on Oct. 30 to Nov. 1. was devoted to the interests of combustion engineers rather than to coal-mining engineers, nevertheless the A.I.M.E. Coal Division was well represented, with 83, or close to one third of those in attendance giving this as their affiliation. The fuels division of the American Society of Mechanical Engineers had 108 representatives, and an equal number reported no society affiliation. Added to the men's total registration was that of some twenty ladies so the total attendance was in the neighborhood of 325, exceeding that of the last two joint meetings, at Birmingham and Columbus, and equaling the 1938 crowd at Chicago.

Jan 1, 1941

By Howard N. Eavenson

DURING the past year, as in the preceding ones, prices continued to fall, production to decrease, and more mines were closed. Much attention is being given by the industry to suggested plans for betterment of its position, and if the scheme recently brought out for consolidation of sales agencies into district agencies is loyally carried out, it cannot but help to improve conditions. The progress in the anthracite industry is shown in the report of its chairman, E. H. Suender; changes in coal preparation are outlined in the report of J. B. Morrow, chairman of Committee on Coal Preparation, while increased mechanization of the western mines is described by Eugene McAuliffe, chairman of the Committee on Machine and Strip Mining. In spite of the depression, interest in the Coal Division has been increasing, its meetings have been well attended, and its committees are active and have been doing excellent work.

Jan 1, 1932