Search Documents

By Halvor Dalaker, Pål Tetlie

The decomposition of methane has been studied experimentally in contact with various oxides at elevated temperatures. For each oxide, the temperature at which the cracking starts has been determined. No correlation was found to exist between the temperature for the onset of cracking for a given oxide and the affinity for carbon of the oxide's metallic component. In terms of potential for using methane as a reducing agent, calculations are presented that indicate that the suitability of an oxide for such reduction depends on the desired methane+oxide reaction being more energetically favourable than the methane+methane=ethylene/acetylene reactions.

Jan 1, 2014

By Marshall T. E, Finfinger G. L

Gulf Coast domal salt mining operations have had sporadic encounters with methane gas emitted without any warning. In virtually all confirmed cases, the methane was localized in methane enriched zones. In a few cases large quantities of methane were expelled rapidly with salt outbursts, resulting in dangerous methane concentrations. Estimates of methane liberated by face blasts in methane-enriched areas is needed in determining how much air should be supplied to the face for proper dilution. A relationship between the gas content of salt samples collected from the face and the amount of methane liberated would be helpful in estimating how much methane will be produced by a face blast. Little is known about the layering or stratification of methane in large area-low velocity airways. This publication reports on three tests conducted by the Bureau of Mines which monitored the immediate return air of four faces during blasting. The test locations were in a methane gas-enriched section that had previously experienced two large outbursts and many smaller ones. A comparison was made between gas content values of face salt samples from the dissolution test and the gas liberation quantities. The characteristic movements of the methane in a large room with low air velocities were charted. This will help to better understand the factors involved in proper placement of methane sensors as a warning system.

Jan 1, 1988

By L Alem

In the field of mineral extraction, complex technologies are being introduced in mines, operators/technicians rely on assistance from an expert (or more) in order to keep their machines functioning. Personnel with such expertise, however, are not always physically on-site. There is a growing need for innovative technological solutions to support effective delivery, just in time, of remote guidance between an offsite expert and an on-site maintenance operator. To meet this need, we have, as part of our Human System Integration project within the CSIRO’s Minerals Down Under (MDU), Transforming the Future Mine theme, explored the usefulness of a number of emerging technologies including: augmented reality, wearable systems and touch table interfaces. This paper presents ReMoTe, an augmented realty system for remote guiding using a touch table interface for the expert station and a combination of augmented reality and a wearable system at the operator end. In designing this system we were interested in exploring the extent to which it can increase the productivity and safety of maintenance personnel. This paper also presents Mobile ReMote, our recent development of a fully mobile remote guiding system. In Mobile ReMote, both the expert and the operator are using a near eye display and wearing a light computer in a back pack. The expert is able to guide the operator using his/her hands on the virtual display, while the operator is able to see the instructions on the rear eye display. Workers in the mining industry are highly mobile, a mobile expert and operator station will meet this need.

Nov 22, 2011

By Cyril S., Smith

WE cannot but marvel at the fact that fire is necessary for almost every operation. It takes the sands of the earth and melts them-now into glass, now into silver, minium or other lead or some substance useful to the artist or physician. By fire, minerals are disintegrated and copper produced; in fire is iron born and by fire is it subdued; by fire, gold is purified; by fire, stones are burned for the binding together of the walls of houses.... Fire is the immeasurable, uncontrollable element, concerning which it is hard to say whether it consumes more or produces more." Thus wrote Pliny in his "Natural History," that great collection of fact and error which constitutes the principal contemporary description of Roman technology and which until the seventeenth century was the authority most often quoted and requoted by those who wrote on metals, as on many other subjects.

Jan 1, 1940

By Robert B. Francini

Longwall mining and pipelines have coexisted since longwall mining was introduced into the United States. How the pipeline operator reacts to longwall mining under their line depends on many factors. This paper outlines the process the pipeline operator goes through to determine the appropriate response when their pipeline is being undermined. Typical mitigation procedures are reviewed. Finally, the paper looks at current design practices for new pipelines that are expected to be undermined during their lifetime.

Jan 1, 2011

By Frank J. Purcell

“Down The Hole” (DTH) hammer drilling is often necessary to advance the casing during pile construction where the test bores have determined difficult drilling conditions with obstructions such as boulders, cobble and glacial till. The use of compressed air to operate DTH hammers in foundation drilling has been a contentious point in many regions of the world due to its potential to disturb the ground around the pile being constructed. There are many examples of damage to adjacent building foundations where compressed air exiting the pile being drilled disturbed the subsurface around the building’s existing piles. This paper looks at the use of compressed air in DTH hammer foundation drilling and the move towards controlling the exhausted air to avoid over drilling the pile, causing potential damage to nearby piles. Simulated models of air flow penetration into the soil of different configurations of drill bits are discussed to highlight design changes employed to better control the air during the drilling process. A case study of the construction of a water-tight pipe pile wall for a building’s underground parking structure is studied to demonstrate the potential of DTH hammer foundation drilling where the air is fully controlled.

Nov 1, 2022

By Derrick Dasenbrock, Mary C. Nodine, Benjamin Rivers

Up to 50 percent of major infrastructure projects suffer impacts to schedule or cost due to geotechnical issues, many of which correspond to risks related directly or indirectly to the scope and quality of site characterization work. The Federal Highway Administration (FHWA) in coordination with industry organizations seeks to address this issue through Every Day Counts (EDC), a program that identifies and deploys proven, yet underutilized innovations at the project level to save time, money and resources. The A-GaME (Advanced Geotechnical Methods in Exploration) is one of the innovations supported under EDC.

By A. Lee Barrett

"THE COAL INDUSTRY of the United States• and Canada has made great progress in recent years. Coal mining in •the old days represented one of the most arduous tasks for labour and industry, but over the years great progress has been made in reducing the effort required from labour. Also, the tonnage produced per man, the cost of the coal per ton, and the overall safety of the operation, have been greatly improved.Looking back over the past fifty years:, the era can be divided into four principal parts: (a) hand-loading, (b) track mining methods, (c) off-track mining methods, and (d) continuous mining. For many years, all of the coal was won by hand-mining methods. The first forms of mechanization •resembled the move from the horse •and buggy to the automobile. Early track mechanical mining methods were usually adaptations of the direct methods involved in hand-mining, with each improvement directed toward some specific process. A revolutionary development came about with off-track mining methods. The first efforts in this direction were provided by off-track mechanical loading machines, which loaded the cars •on track and differed from conventional track mining methods only in that the loading machines themselves operated on the mine floor. With the advent -of the shuttle car about ten years ago, true off-track mining came into being, and real progress in this direction began to be made.At the present time we •are at the beginning of a new era -.the era of continuous mining. There will be a period of development with some time needed before the system is generally applied throughout the industry, but -already enough •has been done to indicate rather dearly what the future holds in this direction."

Jan 1, 1953

By H. R. Manouchehri

"In all electrical beneficiation methods, the difference in electro-physical properties of the contributed mineral particles, essentially frictional charge, electrical conductivity and dielectric constant properties are exploited to achieve separation. The composition of the raw material determines what kind of either corona charging, conductive induction, or triboelectric separation method should be employed. The process is versatile and is influenced by different parameters related to mineral characteristics, surrounding ambient conditions and electrical and mechanical attributions of the separating device. Electrical separation is surface based beneficiation method which is mainly affected by the surface and surface changes of the minerals. Therefore, it is essential to understand how the electrophysical properties of the minerals can be changed/modified. During electrical/electrostatic separation process, both charge magnitude and its polarity that developed on the particles and therefore, their electrical beneficiation potential is essentially defined by surface phenomena. Therefore, it is essential to understand how the main electro-physical parameters can be changed/modified with applied surface treatment/pretreatment methods to promote separation. Surface treatment of minerals is carried out by different means, including chemical conditioning, irradiation, thermal treatment, etc. This paper discusses and analyze the electrical separation process, electrophysical properties of the minerals with special focus on the effect of surface pretreatment/treatment methods to affect electrical beneficiation potential of the minerals. The surface treatment methods vary in a wide range from simple surface cleaning to more complicated chemical conditioning and doping. The knowledge of the solid-state physics and chemistry leads to improve the beneficiation potential of different mineral systems by choosing suitable treatment method(s). Despite the complexity and multiplicity of the charging mechanisms, difficulties in separating fines it seems to be beneficial make our attempts to further investigate and develop the process as dry, low cost beneficiation process, especially nowadays when environmental concerns, as well as energy and water consumptions are main concerns for mining industry."

Jan 1, 2018

By T. Khumalo, L. Musenwa, S. Masemola, M. Kgaphola

"In 2017, Petra Diamonds completed the construction and commissioning of a modern, fit-for-purpose diamond processing plant at Cullinan Diamond Mine (CDM). The design of CDM’s milling circuit is unconventional in that it comprises an autogenous (AG) mill with a grate discharge with large ports, low-revolution jaw crushers, and high-pressure grinding roll crushers with large operating gaps. In this paper we review the design to provide guidance on what is expected from the milling circuit and to demonstrate how the design aims to address challenges experienced in the old plant, which was based on staged crushing technology. We assessed the performance of the CDM AG milling circuit from commissioning and early production stages to examine its impact along multiple dimensions. In the assessment we sought to understand the lessons from our milling circuit regarding diamond liberation, energy consumption, and the future of diamond processing as a whole. IntroductionCullinan Diamond Mine (CDM), previously known as Premier Mine, is an underground diamond mine owned by Petra Diamonds. Petra Diamonds is a leading independent diamond mining group and a growing supplier of rough diamonds to the international market. Petra Diamonds is listed on the Main Market of the London Stock Exchange under the ticker ‘PDL’. Petra’s total resource of 305 million carats ranks third by size after De Beers and ALROSA (Petra Diamonds, 2018).CDM was established in 1902. The mine rose to prominence in 1905, when the 3106 carat Cullinan Diamond — the largest rough diamond of gem quality ever found — was discovered there. The mine has produced over 750 stones that are larger than 100 carats and more than a quarter of all the world's diamonds that are larger than 400 carats. Cullinan is renowned as a source of large, high-quality gem diamonds, including Type II stones, as well as being the world’s most important source of very rare blue diamonds (Petra Diamonds, 2018)."

Feb 1, 2019

By C. E. Arrington, A. C. Rice

"Part 1. REDUCTION AND USE OF OXIDANTSSUMMARYA study has been made of the volumetric determination of molybdenum by reduction in the Jones reductor, receiving the reduced solution in a mixture of ferric alum and phosphoric acid, and titrating with standard oxidizing agents. In addition to potassium permanganate, which has long been utilized for this titration, potassium dichromate and ceric sulphate have been found to be applicable. The latter oxidants have been found to be especially useful in the form of dilute solutions for the determination of small amounts of molybdenum. The tests revealed that certain internal indicators give excellent results in these titrations.Reason for These ExperimentsThe following study was initiated with the hope of providing the mining and metallurgical industries with an accurate and rapid technical method for the determination of molybdenum in such low-grade materials as ores, rocks, tailings, steels, and alloys containing less than 0.3 percent molybdenum. Although the experimental work was designed with this purpose in mind, many of the results are applicable to material containing a higher percentage of molybdenum.While the Bureau of Mines had an experiment station in Colorado, considerable analytical work was done on what were then (up to about 1923) classed as rare metals. One of these was molybdenum; and in Bulletin 212, Bonardi's (1) 3/ 60-page chapter covered all methods for the analysis of molybdenum."

Apr 1, 1939

By S. G. Dixit

Alunite (KAl3(SO4)2(OH)6] is one of the important nonbauxitic resources for aluminum in U.S.A. The major gangue material associated with a unite ore body is quartz. Experimental results indicate that oleic acid flotation of alunite is quite effective in upgrading the ore. The flotation chemistry of the alunite/oleate system has been investigated using various techniques such as: hallimond tube flotation response, measurement of adsorption density using I4C labeled oleated, electrokinetic measurements, infrared spectral studies, contact angle measurements and thermochemical measurements using an isothermal microcalorimeter. Alunite has been found to float readily with oleate in the pH range 4-10.5 and its flotation response is enhanced at higher temperatures. The PZC of alunite has been determined to be at pH 7.2 ± 0.15 which agrees with what would be predicted from solution chemistry and from the flotation response with physically adsorbed collectors. Infrared spectra show a specific peak in the range 1585-1600 cm-1 which has been attributed to the formation of an aluminum oleate surface species. Both adsorption density measurements and infrared spectra indicate that during adsorption multilayers are formed. The heat of adsorption of oleate on alunite has been found to be endothermic and of the order of 4-6 KJ/ mole.

Jan 1, 1980

The dynamic breakage process of rocks by the impact of a hydraulic hammer is more complex than one normally assumes. It is even more difficult when one has to conduct the breakage under water. In such cases one does not know exactly what the surface topography and composition are at the bottom of the sea or river and, hence, it is more difficult to select the best position of the hammer before starting the hammering. Typically, an industrial hammer has a diameter of about 250 mm, a length of about 1.25 to 1.75 m and a mass of several tons. The hammer frequency can be up to 50 impacts per minute. The general principles of rock hammering can be easily summarized, but this knowledge is not sufficient to adapt adequately the method for less common rock conditions (e.g. less brittle rock, presence of vertical and subvertical fractures, etc.). That is the reason why we initiated a research project, whereby a scale model has been developed to conduct experiments in the laboratory and whereby discrete element simulations are being conducted. Both aim at a better understanding of the basic mechanisms of rock hammering. The scaled experimental model allows varying the impact energy and the static weight independently. Within the experiment, the hammer is in contact with the rock specimen under a certain confining pressure and with a certain contact pressure due to the static weight. A weight falls on the hammer, creating the dynamic action or impact; the height over which the weight falls can be varied. The penetration is recorded after each impact. After a certain penetration the test is stopped and the internal crack patterns are described. Some simulations have been conducted, allowing the modeling of individual fracture initiation and growth during the penetration of the hammer by either a constant displacement rate (using the UDEC-code) or by introducing the dynamic process (using the PFC-code). Some of the observed features in the laboratory experiments can be visualized in the simulations. However, further research is needed to allow the simulations being an adequate tool to well understand the dynamic process in laboratory experiments, as well as the in-situ behavior.

Aug 1, 2013

By Cary Hirner, Sarah Lothman, Chris Mueller, Savita Schlesinger, Mike Hanna, Ian Fitz-James

Loudoun Water is currently implementing a quarry to reservoir conversion that will improve water supply reliability in periods of drought and flexibility in water supply operations when turbidity in its Potomac River supplies are high. The Milestone Reservoir Project consists of an inter-tie to the existing Potomac River Pipeline; new pipeline and tunnel; and a pumped intake and outlet works. Planned construction involves significant risks due to underground conditions which includes hard, igneous rock and high groundwater at the creek crossing. In addition, the site is constrained by Goose Creek, an adjacent residence, active mining in a quarry next to the new reservoir, public use of adjacent park space, and the Washington and Old Dominion Trail. Working with these constraints will require close coordination with active mining operations and public and private property owners. Safety of personnel involved with construction also represents a concern with quarry high walls over 30 meters in height near the planned construction. In consideration of key projects risks, Loudoun Water determined that an innovative CMAR delivery approach provided the best opportunity to achieve its goals in quality, innovation, front-end cost and schedule certainty, and operational flexibility and reliability. What matters most to Loudoun Water is the value in having a builder participate in the design process where key decisions can be made based on consideration of risks, cost, schedule, quality, and operability and maintainability of the system. While a progressive design-build delivery model may have produced similar outcomes, Loudoun Water had already invested in substantial development of the design for the work, and ultimately, CMAR provided Loudoun Water the opportunity to retain the partnership with the design team while gaining valuable input from a contractor. Among the challenges with CMAR in the Commonwealth of Virginia is a substantial limitation on self-performance corresponding to 10 percent of the construction value of the work. A significant industry outreach program was initiated by Loudoun Water to encourage participation with incentives in contract terms that allowed for the CMAR Contractor to make a reasonable profit. This paper reviews the CMAR procurement process and discusses contract incentives that were adopted to promote the work within the constraints of contract law in Virginia.

Jun 13, 2021

By Alexander Sutulov

1. INTRODUCTION According to the classical economic approach of the open market economy, copper supply should be regulated by market forces which are (a) demand and (b) prices. In fact, demand is of primordial importance because prices are a reflection of supply-demand balance: they go up in times of shortages of supply and down when over-supply situation exists. In the past few years, this basic mechanism of market economy has been under pressure from a number of non-market forces, such as social and monetary problems of sane important copper producing countries; structural changes in copper mining companies through mergers with oil companies; and other factors which greatly contributed to distortion of the basic supply-¬demand equation. As a result, we have faced in the last three years a situation of oversupply rarely seen in the past, with a catastrophic fall in copper prices, huge losses at mines and unprecedented indebtedness of copper producers. This has deep repercussions in the copper business and its future supply outlook. This is particularly so when taking into consideration that high indebtedness and high interest rates conspire against the very survival of some traditional producers. As we write this comment (July of 1985), close to one half of U.S. copper production capacity is closed down, sane of it for good, while the same precarious situation exists in Canada, Australia, Zambia, and some other primary producers who cannot face present low prices with equally low costs. The question is then what this situation means for the medium-¬term future, until the end of this decade, Particularly when taking into consideration the fact that some of the factors influencing it are of a long-term character. 2. SUPPLY-DEMAND SITUATION IN THE LAST FIVE YEARS Since the last boon year, in 1979, when world copper consumption reached a record of 9.8 million metric tons of refined copper, demand dropped to only 9.0 million tons in 1982, when the crisis bottomed out, and then steadily recovered to the level of 9.7 million tons in 1984. Meanwhile, copper production, which in 1979 was only 9.4 million tons, in spite of the fall in demand, grew to 9.7 million tons in 1981 and 1983 and only temporarily was cut to 9.4 million tons in 1982 and to 9.5 million tons in 1984. As a result of this imbalance, hugh copper stocks were accumulated with supply systematically out¬growing demand by over 2 million tons at one time. With the Western World refined copper demand running at an average of 115,000 tons per week, this oversupply was equivalent to between 15 and 18 weeks production, i.e. twice as large as normal. This was immediately reflected in very low copper prices. Another contributing factor to relatively low copper prices was the lack of speculator interest for this commodity. Between 1981 and 1984 the world experienced a very intensive period of wealth distribution, high interest rates and intensive restructuring off world economy and its industrial sector. Therefore, much of the available money was attracted to more lucrative and attractive investments rather than to the lack-luster performance of copper, and for that matter, of the metal sector in general. The much announced and discussed recovery of the U.S. economy since 1983, and particularly in 1984, with an overall growth of the GNP by 6.8% in 1984, happened to be more oriented to the service sector than the industrial sector and therefore this recovery was not adequately reflected in copper consumption nor to metals in general. This put serious doubts about the future demand for copper. Consequently copper prices failed to improve in spite of an apparent fall in stocks and a healthy increase in the demand for copper since 1982. At the time of this writing (July, 1985), although same analysts claim that the available stocks are running at about 8 weeks of supply, which are considered to be below normal, copper prices are still very low at between 65 and 67 cents per pound of copper. Part of the answer may be the normal seasonal slow-down period in the Northern Hemisphere due to summer vacations and

Jan 1, 1986

By D. Bristow, D. Baker, K. Awuah-Offei, A. ur Rehman

While a body of work exists on intelligent systems for guiding occupants out of buildings during an emergency, the problem of guiding miners out of a mine during an underground emergency has not been explored. Underground evacuation fundamentally differs from building evacuation because of differences in the regulatory regime and uncertainty regarding the number of occupants. The potential for implementing an intelligent miner guidance system is buttressed by the fact that miner tracking systems, along with communication and sensor networks, already exist in underground mines. This work presents a method based on a local positioning system, in the form of a network of “nodes” at major “intersections,” which can then be used to guide miners to safety. We have developed a path-planning algorithm, based on Dijkstra’s algorithm and the local positioning system that can provide miners with the optimal escape path in an emergency. The algorithm is validated with scenarios at the Missouri University of Science & Technology Experimental Mine demonstrating the potential to include smart technology in mine emergency management and response planning. INTRODUCTION Underground mines are hazardous environments with a higher than usual risk of safety emergencies where miners have to evacuate the mine to save their lives. Mines have always trained miners to evacuate or shelter-in-place in minimum time. Jalali and Norrozi (2009) opined that the three major components that help miners in case of emergency are pre-planned optimal escape routes, decreasing delays, and improving the education of miners. In fact, Goodman and Kissel (1990) suggested that fatalities arising from mine accidents could be reduced by 50% just by decreasing delays in finding the pathways in case of emergency. The proposed work can assist miners in finding escapeways quickly in case of emergency. It is very important to have a pre-planned evacuation strategy that is clearly communicated to miners to ensure the safety of all (Conti, Chasko & Wiehagen, 2005).

Jan 1, 2019

The methods used by Newmont Gold Company for deposit modeling are illustrated by examples taken from current operations and advanced projects. These methods vary depending on a number of factors, including geology, mining and processing methods, economic feasibility, and availability of historical information. It is argued that successful modeling requires understanding these factors, knowing the strengths and weaknesses of the various modeling techniques, and being flexible in selecting the appropriate methods.

Jan 1, 1997

By George S. Rice

"It is well known that the lost coal left in the ground in mining, under such conditions that recovery is practically impossible, constitutes a large proportion of the coal in the beds worked. A recent estimate, in a paper on ""The World's Fuel Supply"" presented by Prof. L. P. Breckinridge, of Yale University, before the Annual Meeting of the. American Society of Mechanical Engineers, places the average loss in bituminous coal mining as one-third left in the ground.The bald statement that there is a loss of one ton of coal for every two recovered may seem to those not familiar with coal mining to imply inexcusable and wanton waste. Perhaps a better way of expression is in terms of total recovery rather than in terms of losses. Many mine superintendents and mine owners will readily concede that their total recovery may be only 60 to 75 per cent, but to state that they are wasting 25 to 40 per cent arouses antagonism. The suggestion is of willful waste, whereas the majority of the operators try to the best of their ability to get a high recovery under the adverse and complex conditions that confront them. These involve natural, commercial, and labor conditions, and the requirement in many cases of boundary pillars under railroads and buildings, which may be called for in the deed or lease, or in the absence of specific exemption in the deed or lease, the common law requirement that a surface owner is entitled to the support of the surface."

Apr 1, 1921

By M. K. Boateng, K. Awuah-Offei

"Language barrier in a workplace affects workers’ productivity and safety. The objectives of this paper are to: (1) review the various approaches for breaking language barriers among miners; and (2) analyze the costs and benefits of these approaches, and make recommendations on the way forward. The authors achieve these objectives by reviewing the current approaches in breaking language barriers among miners. The review reveals that some of these approaches can be expensive with less benefits. Thus, it is concluded that mining companies should carefully select the optimal approach to break language barrier. INTRODUCTION Multi-national mining companies have expanded their operations into non-traditional mining destinations to grow and meet market expectations. For instance, Newmont Mining Corporation has about 14 operations and projects located in Africa, Asia, Australia and America (Newmont Mining Corporation Operations and Projects, 2015). Similarly, Freeport-McMoRan operates about 14 mines in North America, South America, Southern Asia, and Africa (Freeport-McMoRan Inc., 2015). Some mining companies have also attracted expatriate workers into their workforce. For example, Ma’aden, the Saudi Arabian mining company, in its 2013 annual report states that 34% of its total employees are expatriates (Ma'aden, 2013). Expatriates constitute a key source of skilled labor and facilitate skill transfer. The success of many international operations relies greatly on expatriate performance (Erbacher, D'Netto & Espana, 2006). Even companies that do not expand their operations into other foreign countries still have to deal with language barriers due to changing language demography of the country and the areas from which labor is sourced. For example, the language composition of the workforce and languages used in South African mines is diverse with miners proficient in Afrikaans, English, Zulu, Xhosa and others to varying degrees (Research Focus (Pty) Ltd, 2011). As a result of these trends, most mines today operate with a multinational workforce. This means cultural differences, including language barriers, exist among the miners. Marschan-Piekkari, Welch and Welch (1999) emphasize the fact that language problems become prominent as companies internationalize and grow their operations into more countries. According to a survey by Forbes, language barrier affects operations. For example, business owners acknowledge that language proficiency may promote a safer work environment (Rubin, 2011). A research has shown that language and cultural barriers in a workplace contributes to reducing workers’ productivity, increasing accidents, and hurts employers’ ability to recruit, hire and retain workers (Morris, 2002). Hence, mines are making efforts to break language barriers in their operating environments. Ma’aden, for instance reported in 2013 that 1,506 of its employees received training in English as a second language (Ma'aden, 2013)."

Jan 1, 2016

By S. Anderson

Advances in inexpensive computer automation led to the development and utilization of a computerized ore control system at Cyprus Coppers tone Gold Mine near Parker, Arizona. These new ore control practices improved accuracy, performance, and productivity of the ore control effort. An automated system for data collection, including bar coding of blast hole samples, laboratory analysis, data management, grade estimation, cut delineation, and ore zone stakeout, plays a major role in ore control practices. This is of particular interest because of the large amount of blast hole information being processed, analyzed, and reported daily.

Jan 1, 1991