Search Documents

By R. P. Fischer

The Colorado Plateau region has been the principal domestic source of uranium, vanadium, and radium. The value of these commodities produced from the region through 1964 slightly exceeds $2 billion. Most of the deposits occur in streamlaid lenses of sandstone in the Chinle and Morrison Formations. The ore minerals below the zone of oxidation are low-valent oxides and silicates of uranium and vanadium; all of these, except the quite stable vanadium silicates, oxidize readily to a variety of high-valent uranium and vanadium minerals. The ore minerals partly replace fossil wood but mainly impregnate sandstone, typically forming tabular ore bodies that are nearly concordant to the bedding of the host rock. The deposits range in size from those containing only a few tons of ore to those containing more than 1 million tons. Stratigraphic, lithologic, and sedimentary structural factors obviously influenced the localization of these deposits, but igneous activity, hydrothermal mineralization, and tectonic structures show no similarly consistent influence on localization. The deposits are epigenetic, but the source of the ore metals, the nature of the ore-bearing solutions, and the time of ore emplacement are uncertain. A few uranium deposits in the region are dominantly discordant to bedding and occur in collapsed breccia pipes or along linear fractures. Their origins are also uncertain.

Jan 1, 1968

By Harold E. Marr

Energy dispersion X-ray analysis was evaluated for possible application in the secondary metals industries for the rapid analysis and identification of copper-base alloys. Laboratory investigations of standard brass and bronze samples indicate that X-ray methods are capable of separating standard alloys into 10 general classes with analytical times of less than 3 seconds per sample for clean, flat samples. A radioactive source of americium 241 with a secondary fluorescer was used as an excitation source, and a lithium-drifted silicon semiconductor detector was utilized for energy discrimination of X-rays.

Jan 1, 1974

Note: This is a progress report and therefore not necessarily conclusive. Further data may result in conclusions somewhat different from those reported here. Crop Growing Season The monthly average temperatures, total precipitation, and evaporation for the demonstration mine are shown in Table 1. [ ]

Jan 1, 1980

By C D. McCullough, M Gerner

Rarely do opportunities arise allowing closure of a mine site to be planned as a key beneficial land use asset within a new urban growth area; particularly so well prior to cessation of mining.Pit lakes are common mine closure legacies for many open cut mines and may form in open cut mine voids extending below the water table upon closure. Mine closure guidelines increasingly require post-mining land uses of equivalent capacity to premining conditions and that minimise long-term post-mining liabilities and maximise benefits to stakeholders and the environment. However, risks presented by pit lakes are regularly neglected in closure planning or are not able to be addressed to allow beneficial end use of the lake or surrounding land.This paper describes strategic planning initiated by quarry owners ten years before mining ceases. In liaison with the planning agencies, the planned closure of a large 100-year-old limestone quarry pit will form a lake on mine completion, with a well-considered beneficial end use in an urban setting in mind. The quarry pit and adjoining land at Batesford South about the edge of the City of Greater Geelong, Victoria, Australia. Geelong is experiencing growth pressures that necessitate development of a new growth area from about 2025.A multidisciplinary expert team assessed the constraints, opportunities and feasibility of rehabilitating the quarry and pit lake and developing the surrounding land as Geelong’s next urban growth area.The concept is exciting and demonstrates that a former mine site could become a valued home to about 40 000–45 000 people. About 30 per cent of the land will also be developed as an ecological riverine corridor including the pit lake that will become a regionally iconic lake as the centrepiece of an urban development.Our paper outlines technical challenges and how these can be met to achieve closure and beneficial use that meets the social, economic and environmental expectations of contemporary urban planning.CITATION:Gerner, M and McCullough, C?D, 2014. Planning for the future – development of beneficial end use from a quarry pit lake, Victoria, Australia, in Proceedings Life-of-Mine 2014 , pp 99–112 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By Reichmuth, Donald R.

Most brittle solids are relatively weak in tension and this weakness can be very significant in determining their performance in structures and excavations. Consequently, accurate knowledge of the tensile strength of brittle materials has long been recognized as important. In the past, measurements of the tensile strength of materials such as concrete, ceramics, and particularly rock have been hindered by problems encountered in fabricating test specimens and in accurately loading them. These difficulties have resulted in a scarcity of published tensile strength data. This can be readily seen in tabulations such as Wuerker's "Annotated Tables of Strength and Elastic Properties of Rocks.

Jan 1, 1968

By Martin Hertzberg

The early and reliable detection of the self-heating of combustible substances in mines is of considerable importance to the mining community. This Bureau of Mines report describes the results of a variety of studies of incipient combustion and its detection. Heated samples of coal, wood, and various polymers were used to evaluate the relative sensitivities of several types of detectors. The laboratory results indicate that submicrometer particulate detection is the most universal and sensitive method. Carbon monoxide detection was as sensitive as submicrometer particulate detection for pyrolyzing coal but was relatively insensitive to pyrolyzing wood or plastics. The conventional type of ionization smoke detector was the least sensitive for coal and of intermediate sensitivity for wood and plastics. Self-heating experiments with Pittsburgh seam coal piles of varying particle sizes gave ignition temperatures of 170° C for 4-to 7-µm dust, which increased monotonically with particle size. The measured heating rates were compared with data from an adiabatic calorimeter to obtain preexponential rate constants. The preexponential rate constants varied linearly with the surface area per unit mass of sample as would be expected for heterogeneous surface oxidation. The propagation behavior of ignition waves and the overall self-heating appears to depend critically on the magnitude of the convective flows induced, which counteract the depletion of oxygen in the void spaces of the pile. Classical theories of thermal ignition require substantial modification to be applied reliably to such cases.

Jan 1, 1977

By A. T. Yu

A recent analysis completed by the United States Department of Commerce predicts that the 1968 Gross National Product will reach a record high of 864 billion dollars. As our nation annually increases its total output of goods and services, as has been the trend, the consumption of steel and its most basic raw material - iron ore - also must increase, To deliver the most economical unit of iron ore to the blast furnace, each segment of the transportation system must be co-ordinated and utilized to its highest degree of efficiency. In some cases, such as with the water segment of the system, a new investment in capacity will be required.

Jan 1, 1968

By A T. Spathis, M L. Lawlor-O’Neill

A methodology for the inversion of a scaled charge weight superposition model to predict peak particle velocity (PPV) has been examined. The inversion involves two steps: first simulated annealing is used to get an initial estimate of the model parameters; and second, these parameters are used as input to a quasi-Newton non-linear optimisation method, used to refine the value of the parameters. The methodology recovers the three required parameters (two charge weight scaling parameters and a time window width) and does this directly from a single production blast for a given point of interest. It has been tested on a synthetic example and recovered the input model parameters successfully in the presence of introduced noise with a coefficient of variation ranging up to ten per cent. Another test used the vibration measurements of three tunnel blasts monitored during the construction of the Citybanan tunnel in Stockholm. In this case, the three model parameters are found from one blast and for a given point of interest, and the PPV at the same point of interest is predicted for the second and third blast fired in the same vicinity as the first blast. The three blasts used different firing sequences. The predicted PPV limits use a confidence interval determined from the scatter in the peak levels obtained from the single calibration blast. The methodology was able to predict an upper bound for the PPV in 21 of the 26 tunnel blast vibrations studied. These predictions improve on a previous study involving the same model but which did not use the inversion process above. Given this reasonable success, further testing of the method on other data sets and alternative forward prediction models is recommended.CITATION:Lawlor-O’Neill, M L and Spathis, A T, 2015. An inversion method for the prediction of peak particle velocity in blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 97–108 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

"The management of outlier grades in positively skewed gold distributions is a contentious issue. Incorporating outliers in standard ordinary kriging (OK) estimation procedures in a way that honours the data without smearing extreme grades into surrounding areas has been problematic. Cutting or capping of outliers to mitigate their influence in estimation techniques is common practice, while methods that manipulate the OK system of equations fail to honour the data. We propose a method of post-processing of kriging weights that provides realistic OK estimates and mitigates smearing without manipulating kriging equations or changing the original grades. The method requires that the data is not clustered, is approximately equally spaced, and is of the same support. Positively skewed data is ordered on attribute grade and nonlinearly transformed to a Gaussian histogram of categorical bins whose frequency is based on their likelihood of occurrence and location in the sample distributions. Factors that restrict kriging weights are calculated by dividing the percentage frequency of data in each bin by the percentage frequency of data in the bin with the highest frequency. Restriction factors applied to the kriging weights in the OK estimation restrict the range of influence in proportion to their probability of occurrence in the distribution. Smear reduction post-processing is easy to implement and addresses issues arising from negative kriging weights while considering the spatial location of samples, the sample grades, and their probability of occurrence. The method mitigates both smoothing and conditional bias.IntroductionOutliers are sample observations that deviate considerably from the standard or expected (Hawkins, 1980). These deviations can be high or low in grade depending on the distribution. The presence of outliers in a mine sampling campaign could provoke mixed reactions. Mining engineers might view high-grade outliers as a promise of achieving higher grades, while the geostatisticians view outliers as affecting the accuracy and precision of the overall estimate, among other issues. Having identified outliers, the geostatistician must decide how to account for their presence and treat them so that true underlying estimates are not distorted. Advanced knowledge of the deposit allows the geostatistician to identify and treat outliers acceptably, especially where samples are limited in number and the true grade distribution is uncertain. If ignored, or treated incorrectly, outliers are likely to lead to smearing of extreme grades into the surrounding estimates, thereby steering regions towards potential under- or over-estimation."

Apr 1, 2019

By J. D. Price, W. M. Bertholf

In preparing a paper on coal washing in Colorado and New Mexico, it is difficult to refrain from entering into a discussion of the historical aspects of this subject, for the story of coal washing in these states goes back well into the last century. This phase of the subject could well make a complete paper in itself, and of necessity this present discussion must be limited to current operations. Therefore, we are taking into consideration only those washing plants which have operated for some period during the years of 1947 and 1948.

Jan 1, 1949

By Evan Evans

IT is appropriate to evaluate 1947 in review as a year of a peacetime record production of about 676,000,000 tons of coal (anthracite and bituminous), closely approaching the extraordinary wartime output in 1944. Considering the general price-wage inflation, it is in point to note that the coal industry sustained the highest wages paid to workers in any major industry, but that coal prices at wholesale levels have risen much less percentage wise than the average for all commodities. The sellers' market continues to prevail. In addition to serving our own country's enormous needs, our coal industry is exporting extraordinary tonnages overseas. This unusual export demand is likely to continue for a while. Moreover, the demand in Europe for American coal mining machinery is a real tribute to the management efficiency of our modern mechanized coal industry. Competitively, the petroleum industry is concerned over its long-term supply, and already a synthetic fuels industry is being publicly advocated. In due time coal and lignite are bound to be

Jan 1, 1948

By H. H. Power

THE PETROLEUM DIVISION of the A.I.M.E. continued with its diversified activities during 1.935. Sessions at the New York meeting in February were devoted to production engineering, domestic and foreign oil production, and petroleum economics. The symposiums on domestic and foreign production proved their increased usefulness. The data accumulated for 1935 were added to those published during prior years in "Petroleum Development and Technology." A joint session on the use of metals in the petroleum industry was held by the Institute of Metals, Iron and Steel, and Petroleum Divisions. W. S. Farish, chairman of the board of the Standard Oil Co. (N. J.), was the principal speaker at the annual dinner. The October meeting, held in Hous¬ton, was characterized by an excellent program and large attendance. Four sessions were devoted to problems in estimating reserves, reservoir energy, properties of drilling muds, electrical logging, water flooding, and other subsurface studies. Foreign representatives of the Anglo-Persian Oil Co. presented a paper on surface tension and specific gravity of crude oil under reservoir conditions. The address by President Buehler, the dinner at San Jacinto Inn, a trip to various lo

Jan 1, 1936

By R. W. Raymond

ALL history testifies that the mineral resources of a region have furnished both the impulse for its first development by man, and the foundation for its subsequent occupation by civilized and prosperous communities. In the pre-historic ages, the hunters, fishers, shepherds and gardeners of the world may have wandered or tarried without regard to the attractions of the mineral deposits which they could not utilize, and therefore did not value. But with the rise of civilization, as expressed in manufactures and commerce, the national value of such deposits began to be realized. Barbarous and remote tribes, possessing the sources of such supplies, won recognition in trade long before they could attain it through any other means. Thus, the North American Indians of Lake Superior exchanged their native copper for the mica of North Carolina; the ships of Tyre sailed all the way to Spain for lead and to Britain for tin; and the fleets of Solomon brought gold from Tarshish. In more modern times it has been chiefly the precious metals that have stimulated exploration and conquest. The inherent qualities and the traditional value of gold and silver sufficiently explain this historic fact, the continued existence and potency of which is evidenced, even in our own times, by the occasional rush of eager adventurers to new districts where gold and silver have been discovered. The history of North and South America has been peculiarly influenced by this factor. It was the prospect of obtaining gold and silver that led the Spanish adventurers to the shores of America, and the conquests of Mexico by Cortez and of Peru by Pizarro were inspired by the stories of the wealth of the Aztecs and the

Mar 1, 1909

By C. A. Fisher

THE discovery of petroleum in Pennsylvania in 1859 marked the birth of an industry of paramount importance. Spreading from - Oil Creek, this remarkable industry may be said to have embraced the earth in a little more than half a century. Those who made the discovery little realized its deep significance or far reaching influence on our national life. For over sixty years, during which time this nation has created and developed the oil industry to a high state of efficiency and' carried its activities to all parts of the world, we have' at all times been the leaders in the production of crude oil and in the development of its technology. During the unprecedented growth and expanse of the oil industry there has been an increasing dependency of our basic industries on, petroleum, until at present it has become essential to our national existence. To meet the ever increasing demand for petroleum and its products, we have explored, at one time or another, for their oil possibilities, practically all parts of the sedimentary rock area in the United States. Furthermore, detailed surface and, in many places, subsurface studies have been made of all the promising regions; over 640,000 jewells have 'been drilled for. oil since the beginning of the industry; $12,000,000,000 have been spent in this work; seventeen major fields exceeding 100,000 bbl. daily production and more than a thousand minor pools have been opened up, and 8,000,000,000 bbl. 'of oil have been produced, or an amount nearly equal to the estimated future reserves of the United States made in 1921.

Jan 1, 1925

By AIME AIME

THE Annual Meeting-numerically the 162d meeting-of the American Institute of Mining and Metallurgical Engineers will be held at the Pennsylvania Hotel, 7th Ave. and 33d St., New York, Feb. 18-22, with the exception of the following events: the Mineral Industry Education Division will meet Sunday afternoon and evening at the Columbia University Men's Faculty Club, 400 West 117th St.; and a meeting of the Section Delegates, the annual business meeting of the Institute, and an executive session of the Board of Directors will be held in that order Tuesday afternoon in the Engineering Societies Building, 29 West 39th St., where the Directors will meet in the evening following their annual dinner to the Section Delegates. The Pennsylvania--one of the Statler group of hotels-was selected as headquarters because it has the physical equipment and facilities-for registration, technical sessions of all sizes, luncheons, social events, etc.-as well as the prominence and location desirable for an Institute annual meeting. (A tip for Tuesday afternoon and evening: You can walk underground from the Pennsylvania to within half a block of the Engineering Societies Building,)

Jan 1, 1945

By Michael Wieland

The thermodynamics work-principle was used to develop the rupture-fracture-throw (RFT) model for ranking the performance of reduced-density explosives when shot in rock or other stratum. The RFT model revises techniques used for the rock-water-jelly (RWJ) model, where the reaction-zone remains trapped within the rock/stratum. Therein, ranking of performance refers to trends for the two resolved components of the total expansion work: the reversible mechanical work taken as the heave and the residual irreversible portion, taken as the undissipated shock. For numeric tractability, the RFT and RWJ thermodynamic efficiency were taken equal, while the RWJ late-stage confinement was replaced with restrained venting through the rock, to render the RFT inefficient heave. The transfer of heat from the reaction-zone was neglected and the root-power formula was used to render the gas-covolume. Ranking trends were found for a generic charge formulation over a wide ranging density, with underwater results noted for comparison. Realistic compositions, some with natural resource materials, were treated for just typical and reduced density. Rock characteristics, ranging from hard rock to weak stratum, were represented by their density and rupture compression strength. Quantitative test results for shock or heave in rock remain difficult, so qualitative guidelines remain helpful when reviewing the graphic trends. Theoretical refinements for rock fragment size-distribution remain under development, though some relationships are touched upon to gain insight.

Jan 1, 2011

By T. Szendrei and S. Tose

Historical approaches to the problem of flyrock based on correlation studies and regression analysis, including artificial neural networks and similar techniques, are inherently incapable of addressing two core issues – root causes of flyrock and projection velocity. A further shortcoming of correlation techniques is that they give no information on the influence of rock size and shape on the flight distance. The scaled depth of burial model for crater blasting in the collar zone and bench face does not specifically address the question of flyrock velocity. A third approach, based on flight trajectory calculations, often neglects the very significant effects of air resistance on the trajectory. Some trajectory models incorporate air resistance but use an implausible fragment velocity model that cannot propel sizeable rocks to distances much beyond 150 m. Nonetheless, trajectory calculation incorporating the effects of air drag affords the most promising approach to the prediction of flyrock range. A unique and insightful feature of the proposed realistic flight modelling is that it collapses all suspected causes of flyrock, many of which are not well understood, to just a single parameter – the launch velocity. This indicates that the root causes of flyrock lie in the mechanisms of momentum transfer to broken rock and suggests new avenues of study.

Dec 13, 2022

By K. Isaac, S. O. Bada

This research focuses on the co-firing of discard coal with refuse-derived fuel (RDF) to utilize this abundant resource in South Africa for energy generation and reduce the volume of waste disposed of at landfills. The potential of a coal with a high ash content (> 40%), which is a grade used in some power stations in South Africa, and its combustion compatibility with two different RDFs in terms of emission reductions has been established. Gaseous emissions and ash residues from the combustion and cocombustion of the coal, two different RDFs and coal/RDF blends of different proportion were analysed. One of the RDF samples contained mostly paper (PB) and the other mostly plastic (PL). Co-combustion ash from the discard coal and RDFs showed a decrease in chloride and alkali metal contents as the coal ratio in the blend increased. The slagging propensity of the co-fired blends was found to be very low, while the propensity for fouling decreased from high to medium for all the blends with < 75% RDF. Cocombustion of RDF with coal showed a decrease in SO2 emissions from 387 ppm (discard coal) to 50 ppm for the sample containing 25% coal discard plus 75% PL. A 15% PL to 85% coal blend also reduced NOx emissions from 145 ppm (100% PL) to 88 ppm. The lowest CO2 emission observed was 6000 ppm for the blend of 85% discard coal plus 15% PB. It was established that the most favourable fuel blend that can produce the lowest sulphur emissions if used for power generation is the 25% coal discard plus 75% PL sample.

Aug 2, 2022

By D K. Weatherley, A N. Mainza, I Govender, L M. Tavares, M S. Powell

It is understood that rocks do not instantaneously transport along a grinding mill and are consequently not perfectly mixed, but this is conveniently overlooked in mill modelling. A lack of understanding of the transport phenomenon and the difficulty of modelling realistic transport in a complex tumbling system, contribute to this. Visual observation of segregation in AG and SAG mills and measured lag time of mill response to changes in feed provide evidence of the influence of axial transport within mills. Incorporating this lag in dynamic models should underpin dynamic simulation of milling circuits for design and for model-based control. Limitations and errors in predicting the influence of increased power via mill length versus diameter, inability to predict pebble production, and a lack of the differential in residence time across rock sizes and competences, all contribute to inadequate design prediction that can be especially acute for large Autogenous mills. Examples of dramatically under – and overloaded pebble regrind circuits and the inability to predict pebble load in AG milling discouraging the application of this energy-efficient option, point to the need for predictive modelling of breakage by competence linked to transport through and out of mills. Incorporating progress in granular flow and mixing, coupled to computational advances enable models to be based on complex breakage and transport models at high spatial resolution. This allows mechanistic models to simulate thousands of times faster than real time, opening the door to more accurate mill design, including dynamics in process simulation and to live simulation for process control – all with advanced mechanistic models. The value of grasping this opportunity is not easily refuted.

Aug 24, 2022

By S. W. Marcuson

Smelting of nickel-copper sulfide ores at Vale Inco’s Sudbury operations commenced in 1888 and the first converting plant went into operation in 1892. As the demand for nickel grew, the smelting operations expanded and by the 1960’s the Copper Cliff Smelter featured the longest converter aisle in the world with space for nineteen Peirce-Smith converters. During this long period, different converting techniques and vessels were employed. The evolution of converting is reviewed with special emphasis on the modifications made to the Peirce-Smith vessel to accommodate the metallurgical and process needs of the changing times.

Jan 1, 2009