Search Documents

By R. A. Basse, W. D. Diment, A. J. Petrina

INTRODUCTION In 1957, diamond drilling on a magnetic anomaly indicated an extensive zone of copper mineralization on what is now the Craigmont Mines property. By mid¬1958, drilling established a copper ore body. Milling commenced in September 1961 at 4536 t/d (5000 stpd) and by the end of October 1977 the mine had produced 339 662.04 t (374,363.9 st) of copper. At present, two-thirds of the mill feed is derived from underground operations and one-third from low-grade surface stockpiles. Craigmont Mines is situated 209 km (130 air miles) northeast of Vancouver (see Fig. 1), 16 km (10 miles) west of the town of Merritt, a logging, ranching, and mining community of about 7000 people. It is serviced by paved highways, Canadian Pacific Railway, British Columbia Hydro, and Inland Natural Gas Co. Water is pumped from the Nicola River, a distance of 6 km (4 miles) and a lift of 244 m (800 ft). In March 1967, the open pit mining operations at Craigmont Mines reached their economic limit and were suspended. Before this, it had been decided that a sub¬level caving method of underground mining would be used to supply ore to the concentrator after the cessation of open pit production. This chapter describes the fac¬tors influencing the choice of mining method, some of the problems encountered, mining practices, and results. GEOLOGY The ore bodies of upper Triassic age are located in a limy horizon striking east-west, closely paralleling the intrusive Guichon batholith, bounded on the south by rhyolites and on the north by graywackes, and dipping steeply to the south (Figs. 2a, b). The ore bodies are relatively narrow with a maxi¬mum width of 79 m (260 ft), a combined strike length of 853 m (2800 ft), and a vertical extent of 610 m (2000 ft). Chalcopyrite is virtually the only copper mineral, and 20% of the ore zone consists of acid solu¬ble magnetite and hematite. The area has been subjected to considerable faulting and brecciation, which is a major factor in the mining operation. Total geological reserves, at 0.7% Cu cutoff, for the deposit were 22 316 743 t (24,600,000 st) at 1.89% Cu. An additional 5 236 270 t (5,772,000 st) at 0.6% Cu were mined from the open pit. Ground Conditions The waste rocks-graywacke, andesites, and diorite -are relatively incompetent due to the high degree of fracturing and jointing, and all require varying degrees of support. The ore zones are somewhat less fractured; ground support is still required, however, although to a lesser extent than in the country rock. Ground conditions in the main ore body are better than in the smaller, nar¬rower ore bodies. Clayey fault gouge is present in most of the faults; gouge zones may be up to 6 or 9 m (20 or 30 ft) wide. The main ground problems are associated with local weakness rather than pressure. Shape of Ore Bodies (Figs. 2a, b and 3a, b) The main No. 1 ore body is approximately 244 m (800 ft) long and 46 m (150 ft) wide. It extends ver¬tically from the original top of the open pit at 4200 ele¬vation to just below the 3060 level. The No. 2 ore body is approximately 304 m (1000 ft) long, varies from stringer width at the extremities up to 79 m (260 ft) wide, and extends from 3060 level to 2400 level. Both these ore bodies have extensions re¬sulting in additional small irregular bodies. Ore bodies are mostly steep dipping, though part of the Wing ore body, an extension of No. 2 ore body, dips at 0.87 rad (50'). This ore body varies in size, but is approximately 122 m (400 ft) long, 21 m (70 ft) wide, and about 213 m (700 ft) high. No. 1 Limb ore body is a narrow extension of the No. I Main with a vertical extent of 137 m (450 ft), average width of 18 ft (60 ft), a strike length of 152 m (500 ft), and dips steeply at 1.4 rad (80°). No. 1 East is an eastern extension of the No. 1 Main with a vertical extent of 183 m (600 ft), a strike length of 91 m (300 ft), an average width of 30 m (100 ft), and dips at 1.2 to 1.4 rad (70 to 80°). No. 1 South is at the upper west end of the open pit with a vertical extent of 76 m (250 ft), a strike length

Jan 1, 1982

By Walter Rose, W. A. Bruce

Improved apparatus, methods, and experimental techniques for determining the capillary pressure-saturation relation are described in detail. In this connection a new multi-core procedure has been developed which simplifies the experimental work in the study of relatively homogeneous reservoirs. The basic theory concerning the Leverett capillary pressure function has been extended and has been given some practical application. Some discussion is presented to indicate the relationship of relative permeability to capillary pressure, and to provide a new description of capillary pressure phenomena by introducing the concept of the psi function. INTRODUCTION For the purposes of this paper the capillary character of a porous medium will be defined to express the basic properties of the system, which produce observed results of fluid behavior. These basic properties may be classified in the following manner, according to their relationship to: (a) The geometrical configuration of the interstitial spaces. This involves consideration of the packing of the particles, producing points of grain contact, and variations in pore size distribution. The packing itself is often modified by the secondary processes of mineralization which introduces factors of cementation, and of solution action which causes alteration of pore structure. (b) The physical and chemical nature of the interstitial surfaces. This involves consideration of the presence of interstitial clay coatings, the existence of non-uniform wetting surfaces; or, more generally, a consideration of the tendency towards variable interaction between the interstitial surfaces and the fluid phases saturating the interstitial spaces. (c) The physical and chemical properties of the fluid phases in contact with the interstitial surfaces. This involves consideration of the factors of surface, interfacial and adhesion tensions; contact angles; viscosity; density difference between immiscible fluid phases; and other fluid properties. Fine grained, granular, porous materials such as found in petroleum reser~oir rock possess characteristics which are expressible by (1) permeability, (2) porosity, and (3) the capillary pressure-saturation behavior of immiscible fluids in this medium. These three measurable macroscopic properties depend upon the microscopic properties enumerated above in a manner which defines the capillary character. Systems of capillary tubes or regularly packed spheres may be thought of as ideal and numerous references can be cited in which exact mathematical formulations are developed to show the relationships governing the static distribution and dynamic motion of fluids in their interstitial spaces. The capillary character of non-ideal porous systems such as reservoir rock also is basic in determining the behavior of fluids contained therein; although, in general, the connection is not mathematically derivable but must be approached through indirect experimental measurement. This paper gives consideration to the evaluation of petroleum reservoir rock capillary character. The methods employed may be applied to the solution of problems in other fields, and the conclusions reached should contribute to the basic capillary theory of any porous system containing fluid phases. In this paper, a modification of the core analysis method of capillary pressure is employed and it is intended to show that the capillary character of reservoir rock can be expressed in terms of experimental quantities. A very general method of interpretation correlating the capillary pressure tests with fundamental characteristics such as rock texture, surface areas, permeability, occasionally clay content and cementation is introduced. Eventually an attempt is made for establishing a method of deriving relative permeability to the wetting phase from capillary pressure data. The experimental evaluation of capillary character must be approached in a statistical manner if reservoir properties are to be inferred from data on small cores. This is implied by the heterogeneous character of most petroleum reservoirs, and suggests that considerable intelligence should be applied in core sampling. Finally, this paper supports the view that once the capillary character of a given type of reservoir rock has been established by core analysis, fluid behavior can then be inferred in other similar rock. Although no great progress has been made in establishing what variation can be tolerated without altering the basic fluid behavior properties, evidence will be presented to indicate that certain reservoir formations are sufficiently homogenous with respect to capillary character that the data obtained on one core will be useful in predicting the properties of other cores of similar origin. Tests have shown that cores under consideration can vary widely with respect to porosity and permeability and still be considered similar in capillary character. EXPERIMENTAL METHODS AND TECHNIQUES Various types of displacement cell apparatus for capillary pressure experiments have been described in the literature. Bruce and Welge; Thornton and Marshall; McCullough, Albaugh and Jones3; Hassler and Brunner; Lever-

Jan 1, 1949

By Charles H. Grant

Some of the limiting factors relative to explosive crushing of rock and ways to overcome a few of these problems are presented. Relationships between borehole diameters, bench heights, and spacings, along with a review of the influence geometry has on energy as these are changed, are discussed. Efficiency in use of explosives and the decay of energy as it moves through rock and is absorbed and dissipated, is described, along with fragmentation as a function of spacings and energy zoning, etc. Communications are one of the major problems encountered. In an effort to provide a better understanding of the use of explosives, it is necessary to take a little different view of what explosives are, how to look at them as tools to fragment rock, and some of the problems encountered in doing so. First, take the explosive: although there are many factors involved, consider these as being reduced to only two — shock-strain imparted to the rock by the high early development of energy, and the gas effect which is a combination of heat, moles of gas formed, rate of formation of these gases which develop pressures, etc. First, consider shock energy by itself and assume there is no gas effect in the reaction. Fig. 1 illustrates a block or cube of rock, in the center of which is detonated an explosive charge which is 100% shock energy. Tensile slabbing would be seen on the surface and probably the cube of rock would generally hang together even though microcracks were formed. If the situation is reversed and an explosive whch has no shock energy and only gas effect (Fig. 2) is considered, the cube of rock would act as a pressure vessel and contain the pressure from the gas effect until it exceeded the rock-vessel strength; then the rock would break in a few large pieces. If these two kinds of energy are put together and the area of shock-strain around the explosive (Fig. 3) is considered, the two energies will be seen working together to furnish broken rock. The gas effect applies pressure to the microcracks formed from the shock energy to weaken the rock-pressure vessel and propagate these cracks to break the rock apart. It not only will be broken more finely, but will break apart at a lower pressure than the gaseffect case, since the shock energy has first weakened the rock vessel. Although tensile spalling from the shock-strain imparts momentum to the rock, the main source of displacement comes from the gas effect. The term "rock" is being used to mean any material to be blasted. These energies are absorbed by the rock in different ways. First, classify rock into two main categories: "elastic" and "plastic-acting." Elastic rock should be thought of as rock which can transmit a shock wave and is high in compressive strength, such as granite or quartzite. Since this elastic rock transmits a shock wave well, it makes good use of the shock energy from the explosive-forming cracks, etc., for the gas effect to work on. Plastic-acting rocks are rock masses which are relatively low in compressive strength and absorb shock energy at a much faster rate, thereby making poor use of the shock energy by not developing as extensive a cracked zone for the gas effect to work on. Rocks of this type are generally softer materials such as some limestones, sandstones, and porphyries. For the most part, the shockenergy part of the explosive reaction is wasted in plastic-acting rock, leaving most of the work to the gas effect. Since the ratio of gas effect to shock energy is different in different explosives, it is easy to understand why some explosives perform well in elastic rock and poorly in plastic-acting rock, and vice versa. Some of the most difficult blasting situations arise when mixtures of plastic-acting and elastic rock are encountered (Fig. 4). Fig. 4 shows an example of granite boulders cemented together with something like a decomposed quartz monzonite which is plastic-acting. The elastic granite boulders will transmit the shock-strain within itself, but when this shock tries to move through the monzonite to the next boulder, its intensity is absorbed by the monzonite and little shock-strain is placed on the adjoining boulder. In addition to this loss by absorbtion, shock reflection at the surface of the boulder will effect tensile spalling. The net effect is poor breakage of the boulders which do not have drillholes in them as they simply will be popped out with the muck. The same is true (Fig. 5) when layers and joints make

Jan 1, 1970

By J. P. Timmons, J. H. Moran, G. K. Miller, M. A. Coufleau

A prototype equipment has been designed and built for the digital recording of well logs on magnetic tape at the same time that the regular film recording is made. The format of the digital tape produced is such that it can be used directly at the input of the ZBM 704, 7090 or other models of ZBM computers which accept digital magnetic tape. This apparatus has been used for the experimental field recording of dipmeter tape logs which were subsequently computed by means of an ZBM 704 or 7090. In this paper the equipment and the digital tape are described briefly, and their application to the computer-interpretation of dipmeter data is discussed. A principal element in the interpretation of the dipmeter log is the correlation of the three microresirtivity dipmeter curves to determine the depth displacements between them. Several correlation methods for computer use are considered, with particular attention to their sensitivity to error and their consumption of computer time. The tape data were used to compute information content of the dipmeter microresistivity curves in terms of their frequency spectra. The results show that the sampling rate used in recording the digital information is quite adequate and illustrate a use of the digital tape in evaluating the characteristics of new tools. Some examples of field results are shown. It can be foreseen that, when digital tape recording becomes available for general field use, a whole new realm of possibilities will be opened up for the processing of other well logs through computations, which hitherto were not feasible because they were too laborious and time-con.sunzing. INTRODUCTION The last few years have seen a revolution in the design and production of data-processing equipment. Stored-pro-gram digital computers have progressed from a research curiosity to the basis of a major industry. There are now hundreds of such machines in daily use in the United States. With the acceptance of a technique that was, in fact, already clearly described by John von Neumann in 1945, the last decade has seen great strides in the development'of components, reliability, programming systems and, most spectacularly, in the sheer number of machines built and in use. In 1957 there were enough digital computers available to the oil industry to justify the suggestion that it would be worthwhile to investigate the possibility of using these machines in processing well log data.' The first result of this investigation was the appearance of what may be referred to as the input-output bottleneck. Well logs are customarily recorded on film. To get these data into a machine required then (and still does): a time-consuming semi-automatic reading of the film; conversion of the log data to digital form; and recording these digital data in some medium acceptable for computer input, such as cards, magnetic tape, or punched paper tape. However, the recording, reading, and re-recording could only result in deterioration of the data. Therefore, it was concluded that the fist step should be the development of a new, more direct recording technique supplemental to the film recording, which would provide easy access to the digital computer. There are many solutions to the problem of recording log data in an easily recoverable form. After careful consideration it was decided to adopt the boldest solution which, it was felt, was also the most elegant. It was decided to record well logs directly, in the field, on magnetic tape in such a way that this tape could be used without further modification as an input to the IBM 704 or 7090 computer. To realize practical field recording of magnetic tape logs, it became necessary to develop in a rather small package, an analog-to-digital converter, a tape recorder, and the necessary multiplexing and control circuits to allow the simultaneous recording of a multiplicity of logging signals. The magnetic tape recording was to be made simultaneously with the conventional logging operation in such a way as not to interfere with it. Along with the development of hardware, it was necessary to begin development of interpretation techniques and machine programs that would exploit the power of the digital computer. Here, again, there is a long list of possible applications. After much consideration it was decided to concentrate on the interpretation of the dipmeter log as a first application. It is the object of this paper to describe in some detail the developments sketched in the last three paragraphs.

By William T. Folwell

The Lucky Friday mine east of Mullan, Idaho, is an outstanding example of a property in the Coeur dlAlene district where a small and insignificant-appearing silver-lead-zinc vein at the surface has changed at depth into a large vein of great importance. The Lucky Friday vein has little if any surface expression and above the 1200 level the ore shoots are small and discontinuous. Between the 1200 level and 2450 level, the lowest developed level, the main ore shoot has shown remarkable improvement on each succeeding lower level, and today the mine is one of the major lead-silver producers in the Coeur d'Alene district. History: The Lucky Friday property is on the north side of the South Fork of the Coeur d'Alene River in sections 25, 26 and 35, T. 48 N., R. 5 E., Hunter mining district, Shoshone County, Idaho. This is about one mile east of the town of Mullan, which serves the eastern portion of the Coeur d'Alene district. The southern part of the property is crossed by a branch line of the Northern Pacific Ry. and by U. S. Highway 10. This highway is the principal road crossing the panhandle of Idaho and connects the district with Spokane, Wash., on the west and Missoula, Mont., on the east. The main portal and surface plant of the Lucky Friday mine is at an elevation of 3365 ft, only a short distance above the valley floor and a few hundred feet from U. S. Highway 10. so the mine is readily accessible for year-round operation. The property is comprised of six claims, known as the Lucky Friday group, owned outright by the Lucky Friday Silver-Lead Mines Co. There are four patented claims, Good Friday, Lucky Friday, Northern Light, and Lucky Friday Fraction No. 2 (Mineral Survey No. 3028), and two unpatented claims, Hunter and Creek. In addition, Lucky Friday owns an undivided one-half interest in the Hunter Creek property. which adjoins the Lucky Friday group on the north: a 90 pct interest in the mineral rights in the Jutila Ranch (160A), which adjoins the Lucky Friday group on the east; and a 60 pct interest in the Lucky Friday Extension claim group, which adjoins the Lucky Friday group on the west. The company also has a long-term mining lease on the Hunter Ranch, which adjoins the Lucky Friday group on the west. The claims of the Lucky Friday group were located between 1899 and 1906. The Lucky Friday Mines Co. was organized in 1906 and did considerable exploration work by surface trenching and shallow underground workings, only to see the property sold by the Shoshone county sheriff to satisfy labor claims totaling $2000 in 1912. Another firm, Lucky Friday Mining Co., bought the claims in 1914 and spent 12 years driving what is now known as the tunnel level crosscut. This tunnel intersected a vein previously exposed in a higher tunnel, but it was only a few inches wide. The vein was followed a short distance westerly but was so unpromising that the work was discontinued in favor of extending the main crosscut tunnel several hundred feet north. No ore was found and all work was discontinued. The property was held in such low esteem by the firm that it let taxes amounting to less than $15 a year go delinquent for nine years. Then the property lay idle for two more years until in 1938 John Sekulic, a Mullan service station operator, took a lease, with a $15,000 purchase option, on the advice of an old miner who had worked in the mine. Sekulic re-opened the tunnel level crosscut and explored the vein with an easterly drift for about 200 ft. The vein was too narrow to be of commercial value but was believed interesting enough to warrant further exploration at depth. Lacking funds to explore the vein at depth, Sekulic tried to get the district's larger operating companies to take over his lease and option. They were not interested because of the lean tunnel level showing and the fact that the property lay between the White Ledge fault on the north and Osburn fault on the south, an area which geologists always considered unworthy of exploration. Sekulic then organized the present company and assigned his lease and option to it for stock. This was in 1939. Enough stock was sold locally to finance sinking of a shaft 100 ft from the tunnel level east drift. The vein at this additional depth still was not commercial but showed some improvement. Treasury stock was offered at 5 to 10C a share

Jan 1, 1959

By J. R. Schneider

INTRODUCTION Landowners in Texas for many years have freely granted, reserved and leased "oil, gas and other minerals" or interests therein. In recent years we have witnessed much litigation concerning what sub- stances should be included as "other minerals" within the phrase "oil, gas and other minerals," and this question has received the attention of numerous legal scholars. At the South Texas Uranium Seminar held in Corpus Christi, Texas, in September, 1978, Mr. William R. Dodson presented a paper dealing with this very subject and entitled "Uranium - Mineral or Surface? Who Owns It?" In his paper, Mr. Dodson reported on two recent Texas Supreme Court decisions, Acker v. a, 464 S.W.2d 348 (Tex. 1971) and Reed v. Wylie, 554 S.W.2d 169 (Tex. 1977). which held that the particular substance in question in each case is not a mineral within the phrase "oil, gas and other minerals" if substantial quantities of the substance lie so near the surface that production will entail the stripping away and substantial destruction of the surface. Since that time another chapter has been written in the Texas saga of "When is a Mineral not a Mineral?" and it is the intent of this paper to present an update of the Texas law. A review of the early Texas cases so ably covered by Mr. Dodson in his paper will not be repeated, except as is necessary to illustrate the evolution of the legal doc- trine which has been so aptly named "The Surface Destruction Test". BACKGROUND In order to appreciate the genesis of the problem, one must consider that oil and gas production commenced in Texas many years ago, Spindletop came in in 1901. As oil and gas became more valuable, land- owners with considerable frequency sold interest in the oil, gas and mineral estates in their lands, and reserved interest in the oil, gas and mineral estates in their lands when they disposed of their property. Due to the oil and gas background, and perhaps be- cause oil and gas was paramount in the minds of the parties, the traditional language employed in these grants and reservations was "oil, gas and other minerals" or variations thereof. There are literally hundreds of instruments employing this language constituting a link in the chains of title to thous- ands of acres of Texas land. In addition, there are thousands of acres of Texas land held by oil, gas and mineral leases, the primary terms of which have been perpetuated by production, containing similar language in their granting clauses. The severance of the mineral estate from the surface estate results in two separate and distinct estates, each having all of the incidents and attributes of an estate in land. with the surface estate being the serviant estate, and the mineral estate being the dominant estate and having certain easements in the surface estate to explore. produce and remove the minerals. Harris v. Currie. 176 S.W.2d 302, 305 (Tex. 1943). As observed by the court in the Harris case, this is because a grant or reservation of minerals would be wholly worthless if the grantee or reservor co~lld rwt enter upon the land in order to explore for and extract the minerals granted or reserved. Although the Texas law has recognized that an oil and gas lessee has the right to use so much of the surface as is reasonably necessary to produce the minerals. Warren Petroleum Corporation v. Monzingo, 304 S.W.2d 362, 363 (Tex. 1957), recent decisions of the Court have qualified this doctrine. In Getty Oil Company v. Jones. 470 S.W.2d 618 (Tex. 1971). Getty's pumpine, units were interfering with ones self-propelled sprinkler system utilized for irrigating the premises, and Jones sought to require Getty to install the-pumping units in cellars so that the sprinkler system could pass over them. In an effort to accommodate both the surface estate and the mineral estate, the court held (page 622) "...where there is an existing use by the surface owner which would otherwise be precluded or impaired, and where under the established practices in the industry there are alternatives available to the lessee whereby the minerals can be recovered, the rules of reasonable usage of the surface may require the adoption of an alternative by the lessee". Bearing in mind that the "reasonable use doctrine" grew up in the oil and gas industry involving sub- stances which can be produced by methods that do not destroy or deplete the surface estate, the question presented is whether the Texas courts will extend this doctrine to situations where claimants of "other minerals" seek to produce shallow deposits of iron ore, coal, lignite and uranium by surface mining methods which do destroy or deplete the surface estate? The surface destruction test has answered this question in the negative, at least as to iron. coal and lignite. However, the multitude of mineral estates in Texas which have been created by a grant. reservation or lease of "oil, gas and other minerals" will, doubtlessly, continue to fuel the fires of litigation. EARLY TEXAS DECISIONS In view of the evolution of the Surface Destruc- tion Test, an exhaustive review of the early Texas

Jan 1, 1980

By Samuel H. Dolbear

THE value of a mine is basically dependent on its capacity to yield profits. Since the ore must be mined, treated, and sold, some of it in various future years. there is a risk involved as to future costs, selling price, and working conditions. It cannot be expected that the economic condition existing at the time of valuation will continue unchanged for long periods in the future. During the past 20 years, mineral production in the United States has been conducted under a changing economy in many respects more exacting than that applied to other businesses. There have been increased production incentives, technical aid, exploration of privately owned mineral deposits by government at federal expense, and liberal loans for development and equipment, with risk partially assumed by government.. Some of these benefits have been counterbalanced by price ceilings, consumption controls, and stimulation of competition from foreign producers who have been offered the same advantages extended to American operators. For the present, mines will operate under a government policy directed toward reducing federal aid and control. The tenure of this change will depend upon future elections and the status of foreign relations. War and threat of war are now of the most vital significance to the mineral industries. Other factors which influence cost of production, markets, and price of mine output might be classified as Acts of God or Acts of Government. In some countries expropriation and the difficulty of exporting earnings or investment returns are risks that must be considered by foreign capital. Recognizing that this retards American investment in foreign countries, the Mutual Security Agency offers insurance against such expropriation and guarantees the convertibility of capital and profits. Since it is impossible to predict with certainty either cost of production or selling prices of metals for long periods, some assumptions must be made as to profits in the future. The basic assumption must be that the price of the company's product will vary in proportion to changes in operating cost. There is often a lag in this reaction, however, for prices of minerals are generally more sensitive to declines and less sensitive to increases than are costs. This reflects in part the resistance of labor to downward wage revision and a corresponding alertness in realizing its share of price advances. Some labor contracts include automatic adjustments to metal prices. Notwithstanding the complexity of the, problems involved and the difficulty of weighing their effect on value, such risks may be appraised with reasonable accuracy and a rate of earnings adopted that is compatible with the risk. It is, of course, possible to revert to a yardstick of value such as the commodity dollar, which has been advocated from time to time, but while revaluation in 1933 disturbed public confidence, the theoretical gold dollar continues to be the standard of greatest stability. Its gain or loss in purchasing power is reflected ultimately in cost of production and selling price of the mine product. At present 35 dollars are allocated to one ounce of gold. Measurement of Risk In the application of the Hoskold and most other formulae, a yearly dividend rate commensurate with the risk involved is set aside out of annual earnings. If the risk is great, this rate may be 15 to 25 pct of the amount invested. The remainder is placed in a sinking fund invested in safe securities such as high grade bonds or conservative equities, and the interest or dividends from these securities are added to the sinking fund. The sum of these sinking fund payments and the compounded interest at the end of the mine life is taken as the value of the mine. Admittedly the decision as to the size of the risk rate is the most difficult element in valuation and one requiring the most exacting consideration. It is necessary to look years ahead in an effort to determine future costs, market prices, demand, competition which may develop, including that of substitutes, and other influences common to the mine and to the region in which it is situated. Another phase of risk is the enactment of unfavorable legislation, taxes, and what appears to be an alarming spread of nationalization and expropriation. Capital is sometimes borrowed from the government to finance strategic production. Such loans may be collectable only out of production and involve no liability otherwise. Valuation in these cases must recognize the effect of such a reduction in liability. Offsetting some of these risks are the possibilities of mechanization and other cost-reducing discoveries, improvements in mining and treatment methods, new uses for minerals and metals, and normal growth of markets. In this paper, the terms risk rate, dividend rate, and speculative rate are synonymous. Safe rate and redemption rate are also used interchangeably. These alternatives are used here because they are commonly found in the literature on mine valuation. In Michigan, the State Tax Commission has long employed a risk rate of 6 pct in its valuation of iron mines. There the outline of reserves is well established and operating costs and conditions are based on adequate experience. The following comment on rates appears in the report of the Minnesota Interior commission on Iron Ore Taxation submitted to the Minnesota Legislature of 1941.1 Most engineers agree that 7 percent for the specu-lative rate is "an absolute minimum". C. K. Leith in

Jan 1, 1954

By James P. Connell

HISTORICAL BACKGROUND The American Concrete Institute defines shotcrete as "mortar or concrete conveyed through a hose and pneumatically projected at high velocity onto a surface." This definition thus includes what is traditionally known as gunite, which is a pneumatically applied mortar. In mining practice, the term shotcrete is restricted to pneumatically applied concrete, and this differentiation will be used in this chapter. In 1914, following the invention of the mortar gun in 1907, then chief engineer of the US Bureau of Mines (USBM) George Rice developed the gunite process for underground test work at the USBM facility at Bruceton, PA. After World War I, gunite was used extensively in American mines and was also utilized for underground civil works such as the San Jacinto tunnel in California. The greatest development was in Europe where, as early as 1911, gunite was successfully used as an overlay for deteriorated tunnel linings. In 1951, the Swiss firm Aliva developed a pneumatic gun capable of handling coarse aggregate, thus making possible the first use of shotcrete at the Maggia hydropower development. Initially, shotcrete was used to reduce manpower requirements for forming and placing conventional concrete. However, by 1954 Sonderegger was reporting that the structural advantages of shotcrete were derived from its flexibility and from the fact that it could be applied almost immediately after the opening had been made. The incorporation of wire mesh into the shotcrete led to the new Austrian tunnel method or NATM. The use of shotcrete in American mines has been implemented more recently. This delay seems to be due to previously unsuccessful experiences with gunite as a structural material and to the US reliance on wood or steel supports in main-line haulageways. The long experience with the apparently more substantial rigid supports led mine operators to be reluctant to accept the new and seemingly unrealistic lighter shotcrete support. APPLICATION REQUIREMENTS Shotcrete is a relatively new material for use in underground support systems. Consequently, experienced miners are not always available who are capable of applying the material effectively. Shotcrete, particularly in the small cross sections typical of mine shafts or haulageways, is applied in cramped quarters under less than ideal conditions. Adequate lighting should be made available. The surface should be clean and free of running or dripping water. It may be necessary to collect flowing water in plastic pipes or water collection devices. Any dry cement dust from previous shotcrete applications should be washed from the surface in order to assure a good bond. The US Bureau of Reclamation (USBR) while shooting test panels at the Cunningham tunnel in 1974, found that experienced shotcrete operators were able to obtain up to three times greater compressive strengths than were obtained by unskilled operators using the same equipment and shotcrete mix. ENVIRONMENTAL AND SAFETY REQUIREMENTS Since sodium and potassium hydroxide, as well as other moderately toxic compounds, are often contained in shotcrete (particularly where accelerators are used), safety precautions must be taken to prevent skin and respiratory irritation. Nozzlemen and helpers are required to wear gloves, protective clothing, and ventilation hoods with a filtered air supply. Respirators approved by USBM, equipped with chemical filters that will not pass the caustic mists, may be permitted in lieu of hoods if goggles or safety glasses are worn. Protective ointments are available to reduce skin irritation. All air and shotcrete feed hoses should be equipped with safety-type couplings and secured with safety chains at each coupling to prevent whipping in the event of a hose or coupling failure. Some environmental effects can take place down-stream from the development face being supported. The accelerator compounds, as well as the portland cement used in the shotcrete, will be found in the rebound material which falls to the invert of the heading. Since these compounds may be leached from the rebound material and carried by the drainage system, it may be necessary to install neutralizing or other water treatment facilities. Investigations may find that the final reaction with other compounds being leached from the mining operations may result in a more or less environmentally acceptable end product. USES OF SHOTCRETE General Uses Shotcrete, as a combination of cement, aggregate, and accelerator, is utilized for underground openings such as shafts, adits, haulageways, and service chambers for the following general purposes : (1) primary sup¬port; (2) final lining; (3) protective covering for excavated surfaces that are altered when exposed to air (the protective covering may be of a temporary or final nature); (4) protective covering for steel or wooden supports, rockbolts and rockbolt plates, heads, nuts, and other mats, including wire fabric, used to prevent rock-falls; and (5) as a lagging material in place of timber, steel, or concrete between steel or wooden supports. These applications can be grouped into three general use categories: shotcrete used as a rock sealant, shotcrete used as a safety measure, and shotcrete used as a structural support. Use as a Rock Sealant Thin applications of shotcrete can reduce or prevent slaking of shales or other rocks that are altered when exposed to the wetting and drying cycles created by mine ventilation circuits. While shotcrete may be effective in preventing such rock alteration, at the present time it is not as economical or efficient as other commercial sealants. However, if the sealant property can be incorporated into the structural support capability, the added contribution is usually helpful. Thin applications are not usually sufficient if the alteration of the

Jan 1, 1982

By Denis G. Maxwell

INTRODUCTION It is my intention in this paper to deal with gold, uranium, diamonds, platinum, manganese, chrome, vanadium and heavy mineral sands. These are the most important strategic minerals produced by the Republic of South Africa which are not covered in other sessions of this program. In each case I have high- lighted the statistics and peculiar advantages which combine to make South Africa a vital source of these minerals. Before proceeding to give individual attention to these minerals I believe it would be useful to define what I mean by 'strategic'. The Concise Oxford Dictionary defines strategic in the context of materials as 'essential for war'. However it is commonly used in a much broader sense than this (often, in fact, very loosely) and I prefer to define it as 'concerned with the acquisition and maintenance of power, whether economic, political or military.' A VITAL SOURCE In dealing with the individual minerals I have quoted statistics which are contained in Tables 1, 2 and 3. Table 1 clearly shows the absolute size of the South African mineral industry. However, it can also be used to demonstrate the importance of the industry to the South African economy if compared with the GNP in 1980 of about R60 billion. Table 4 illustrates clearly how important South Africa is as a supplier of these minerals to most of the important industrialized countries of the Western World. Gold If anyone had any doubts about the inclusion of gold in a list of strategic minerals I am sure that the above definition of 'strategic' will convince them that it certainly belongs there. Similarly no one is likely to have any doubt about the fact that South Africa is a vital source of supply. Tables 2 and 3 show that in 1980 we had 51% of the world's reserves and accounted for 55% of world production. The figures for the Western World are considerably higher. The only other major producer, of course, is Russia, with small but significant production in the Pacific Rim area coming from Australia, Canada, Latin America, Papua New Guinea, Philippines and the U.S. All South African mine gold production is shipped in bullion form containing about 88% gold and 9% silver to the Rand Refinery which is a modern refinery with large scale units capable of refining half a ton of bullion at a time. The Refinery is equipped to produce standard 'good delivery' gold as well as 9999 gold and 999 silver. The Refinery also produces the 22 karat blanks which are, used by the South African Mint to produce Kruger Rands. It goes without saying that the South African gold mining industry leads the world in all aspects of deep-level, narrow-reef mining technology. The industry's metallurgists, too, have a record of tenacious and continuing efforts to improve extraction to the level of the present finely honed efficient process used on all the modern mines. Uranium In 1980 South Africa had 14% of the uranium reserves of the Western World and accounted for 14% of production. In view of the paucity of data I am not in a position to estimate figures for the total world. All the other major sources of uranium in the Western World are situated around the Pacific Rim, with the U.S. and Canada already being major suppliers and accounting for 38% and 17% of Western World production in 1980. Australian production at the time was small but they have very large reserves and production is already rising rapidly. The U.S., Canada and Australia account respectively for 22%, 19% and 29% of the uranium reserves of the Western World. South Africa has been a major producer continuously for 30 years. Nearly all the uranium produced, amounting to about 115 000 tons up to the end of 1981, was a by-product or co-product of gold extraction. During that time the industry has frequently led the world in technological innovation, and has established a reputation as a reliable producer of a consistent, high-grade product. In the latter respect, it is helped by the fact that production is marketed by one company, Nuclear Fuels Corporation, which also blends, dries and calcines the product from the individual mines and samples and assays it before shipping. Diamonds Diamonds are the rock on which the South African mineral industry is founded. The discovery of diamonds in 1866 gave rise to the first major mineral industry in the country and the profits from diamond mining helped to finance the gold mining industry 20 years later. Although now overshadowed by gold, diamonds are still very important in the overall picture of mineral production and exports, as can be seen in Table 1. There are really three separate diamond markets - gem, natural industrial, and synthetic - and, to be meaningful, statistics should be provided separately. Unfortunately separate figures are not available. The figures in Tables 2 and 3 show that, for gem and natural industrial together, South Africa ranks third in the world in production and second in reserves. South Africa is a major producer of synthetics and probably ranks second in the world after the U.S. Recently, of course, Australia was the scene of a major diamond discovery and will soon become the only

Jan 1, 1982

By Paul Sarnoff

The economics of precious metals -- depending upon who is involved --could be the economics of hope, of fear, indeed of profit and perhaps survival. For those investors seeking capital gains in a puzzling economy, precious metals involve the economics of hope. Those who are convinced that currency soon won't be worth the paper it's printed on turn to precious metals because of the economics of fear. Gold and silver have been a storehouse of wealth since biblical times. The economics of fear during the past 500 years on the Continent has caused almost every European family to make sure a private stockpile or hoard of gold, silver or coins is at hand in case the paper currency of their country undergoes the kind of disaster that came to the German Mark after World War I. Understandably, for mining companies involved in the production of precious metals, the elements of operations and management are directly concerned with the economics of profit -- and perhaps survival. To the American miner the price of precious metals in the marketplace is a matter of daily concern. After decades of selling silver to the US Government at 64.64 cents an ounce, producing silver mines suddenly became faced with prices breaking $5, $10 and $20 per ounce, and approaching $50 an ounce during the period 1978-1981. What should the miner expect one year in the future? Five years?

Jan 1, 1981

By Valérie Léveillé

As new legislation drives to lower SO2 emissions from metallurgical plants, plant managers face the challenge of keeping their costs under control. The Cansolv® SO2 Scrubbing System has been broadly adopted in the non-ferrous industry as a cost effective solution for smelter operators to meet the new SO2 emissions targets. The Cansolv® SO2 Scrubbing System is an amine-based regenerable process that selectively absorbs SO2 from a variety of gases, including dilute smelter gases, such as furnace and converter gases. The system produces a pure, water-saturated SO2 byproduct stream, which can then be directed to the front end of a sulfuric acid plant for conversion to sulfuric acid. When deployed in a smelter complex, the Cansolv® SO2 Scrubbing System may also be used to process acid plant tail gas, allowing single absorption sulfuric acid plants to achieve emissions an order of magnitude lower than that of a double absorption acid plant with a lower capital investment. Depending on inlet gas temperature SO2 emissions in the treated gas can be controlled to as low as 55 mg/Nm3. This paper will describe some of the applications where customers have or are planning to use the Cansolv® SO2 Scrubbing System and what as well as which features and cost advantages for the treatment of smelter gases were key to the technology choice.

Jan 1, 2009

By Noel C. Joughin

In making judgements on tolerable levels of risk in industry, and in all spheres of life, it needs to be understood that every action gives rise to risk. Without risk, nothing can be done. Without risk, no economy could be advanced. There is a strong tendency to emphasize the risk at work, but persons who are not working are exposed to a different set of risks. Often persons who are not working face greater risks than persons who are working. Simply, in being alive, one is exposed to the risk of an accident, the risk of contracting a disease, and an extremely diverse variety of other risks. According to the Health and Safety Executive of the UK, it is not possible to have a state of zero risk, because ?a state of zero risk does not exist?. Because zero risk is a physical impossibility, it is not possible to design for a state of zero risk in all engineering design. While the strategic target of achieving zero risk is laudable it does not provide any practical guidance to engineers as to what acceptable limits of risk should be. This causes a significant and real problem in the design for and the management of risk. Without meaningful guidelines, engineers, managers and the authorities often find themselves in disagreement. Thus, it has become essential to establish criteria for tolerable levels of risk and unacceptable levels of risk in order to design and manage engineering systems properly.

Jan 1, 2011

By J. T. Crawford

Although nearly 10 pct of the total tonnage of coal produced annually within the United States is handled by bulk freighters on the Great Lakes, very little of the detail connected with it has been published other than occasional newspaper stories and publication of tonnage statistics. Of the total tonnage floated on the Lakes each year some 10,000,000 is stored and distributed from the port of Duluth-Superior, at the western end of Lake Superior commonly known as the Head of the Lakes. This port has the largest single area concentration of coal docks in the world. Since this area contains the largest ore docks, the largest movable material handling bridge, the largest and highest grain elevator and the largest coal bri-quetting plant in the world, it is entirely fitting and proper that here also should be located the largest coal dock and what we believe to be the world's largest clam shell. Of the sixteen coal docks operated by ten companies, five are owned and operated by the North Western-Hanna Fuel Co. which has two docks on the Superior, Wis., waterfront and three docks in Duluth, Minn. It is with these five docks that we are primarily concerned, General History In the summer of 1871 a small sailing vessel entered the harbor of Duluth-Superior with the first commercial coal cargo. All the coal brought up that first year did not amount to more than 3000 tons. During the year 1877 the first dock equipped for handling coal was built in Duluth. Coal receipts increased to 52,785 tons in 1879 the first year for which an official record was kept. Since then the volume of water-borne coal to the Head of the Lakes steadily increased to a maximum of 12,688,321 tons in the year 1923. This tonnage was nearly equalled in the year 1927 and the next highest tonnage recent year was in 1946 when 10,105,703 tons were unloaded. The average annual bring-up over a ten year period 1938 to 1947 was 8,605,231 tons. Approximately 30 pct of the coal unloaded at the Head of the Lakes is handled over the docks of the North Western-Hanna Fuel Co. Competition of other fuels coupled with expansion of coal fields in the mid-west have held coal receipts for Duluth-Superior at a relatively constant figure during the last eight years although the total tonnage of coal floated on the Great Lakes has more than doubled in the past 25 years. From the shovel and wheelbarrow method of unloading early cargoes to the horsepowered windlass derrick with a wooden tub was but a short step. The first movable coal handling, steam operated,

Jan 1, 1949

By Leroy G. Hagenbuch

"IntroductionAn integrated Truck Management Information System (Truck MIS) evolves as seemingly separate functions combined to yield a single homogeneous result / product. The concept of a computer integrated Truck MIS includes truck dispatch, truck maintenance management and truck weighing.A truck management system is only as good as the information / data bases input to it. The concept of an integrated system works best with automated data gathering. Automated data gathering provides timely and normally, the most accurate historical information/data bases. Data bases are, however, historical, which is a problem to be overcome in a computerized truck management information system, especially in regards to a truck dispatch system as loading sites / loading conditions and some dump site conditions continually change. As these changes occur, data base s must change as well, and thus the need for the continual update of data bases that the computer uses for a Truck MIS.For a truck dispatch system to achieve reliability / viability, dispatch decisions need to revolve around real time data gathered in an automated way. Integration of all truck management function s through automated data gathering lead s to the best over-all system.An integrated system is a combination of many different factors and is only as good as each factor / building block put in the system. With the proper building blocks, an integrated Truck MIS is very feasible - an MIS System that includes weighing, time and motion study, truck maintenance and maintenance management, as well as truck dispatch.Truck MISAn integrated Truck MIS provides for truck dispatch as the ultimate end result, a truly automated /integrated truck dispatch system (to function non-operator-dependent). The following comprises its central building blocks:-Time.- Haul Cycle Segments.Truck Status, i.e. Load on truck,- being loaded,- loaded,- unloaded,- in service,- out of service.- Vehicle Location.Loading Equipment Status.- in service,- out of service.Optional- distance travelled in each haul segment.With this data provided on a non-operator dependent basis, it is possible to build good data bases so a computer can make truck dispatch decisions. Knowing what information is needed as the central core to a good Truck MIS, how can this information be automatically gathered and fed into a central control computer?"

Jan 1, 1986

By Charles Clayton

CAST-STEEL runners, while not interesting from a commercial standpoint, furnish valuable material for microscopic study. Foley1 found not only the usual ingot structure, but zones of Widmannstattian structure, which he explains as due to differential crystallization. The writer, in examining nickel-steel runners, found a type of pro-eutectoid ferrite that is unusual and most probably new. The runner in question was 8.75 cm. (3.5 in.) in diameter and analyzed at its center 2.69 per cent, nickel and 0.350 per cent. carbon and at its edge 2.62 per cent. nickel and 0.359 per cent. carbon. The macrostructure, which is the usual type, is shown in Figs. 1 and 2, which are a cross-section and the longitudinal surface, respectively. Slight segregation of ferrite can be seen near the center of the segment and at other points near the edges of polyhedral grains. Stead's reagent brings out the dendritic structure within the grains as shown in Figs. 3 and 4. This texture is what would be expected of such a steel. Figs. 5 to 10 show the peculiar swirls of pro-eutectoid ferrite, the finding of which prompted this paper. These swirls, or eddies, if such a term can be applied, occur in all parts of- the runner and in all parts of the individual grains. I he tipper left-hand figure shows this ferrite at a grain boundary; the middle left-hand figure shows the inner portion of a grain; and the lower left-hand figure shows these swirls at the edge of a grain which is also the outer edge of the runner. Straight-lined ferrite associated with swirls is found in the areas of Figs. 11 and 12. The texture of the carbon-bearing constituent of the runner is shown to- some extent in Fig. 12, the pearlite being very fine or sorbitic. Higher magnification does not bring out any new features either in the peculiar ferrite or in the pearlite. Figs. 13 and 14, at 240 diameters, show the curved and straight-lined ferrite.

Jan 3, 1920

A. 11. P. WYNNE, San Jose de Gracia, Sinaloa, Mex. (communication to the Secretary): In the comparative tests reported by Mr. Tays, the stamp-batteries were provided with various styles and mesh-sizes of screens, while the Bryan mill was run throughout with a slot-punched Russia iron, equivalent to a 30mesh wire screen. This is a somewhat onc-sided method of comparison. Should not the Bryan mill also have had the chance to show what it could do with other screens? I cannot wholly approve Mr. Tays's proposed improvements upon the Bryan mill. In my judgment, the inventor has given us a machine well-adapted to the work for which it was designed, namely, the crushing and amalgamation of soft ores. In my judgment, the principal cause of failure to amalgamate satisfactorily in the Bryan mill is not, as Mr. Tays thinks, the shallowness of the basin, or the lack of copper plate about the inside periphery of the mill, but rather the want of experience and practical knowledge on the part of most amalgamators. Having had experience, not with one Bryan mill only, but with several, and taking into consideration the experience of other capable mill-men, I am positive that the proper way to save gold ill this mill is: first, to use enough quicksilver to keep the amalgam liquid, thus allowing it to accumulate in the annular space between the dies and the rims of the basin; secondly, to replace the old dies, when a little more than half worn-out, with new ones; and, thirdly, to clean up the mill at least every two weeks—or oftener, if rich ore is being treated. It is evident that Mr. Tap endeavored to amalgamate quite " hard," as is done in a stamp-battery, in which case the swash of the pulp would scour off portions of the hard amalgam adhering to the inside plates and dash it through the screens— after which a considerable amount would be lost through floating on, or in, the pulp in its journey over the outside plates, and

Jan 1, 1900

By E. Sigal

Overview ?Intrinsik has completed several wide area HHRA and ERA studies of mining and smelting communities ?Several ?Lessons Learned? ?Key areas related to: ?Study Design ?Data Quality ?Bioaccessibility ?Speciation ?Weight-of-Evidence Approaches ?Advances in Ecological Risk Assessment Techniques

May 1, 2009

By T. N. Moore, E. M. De Souza

J. Dasher Regarding the March 1991 ME technical paper by De Souza and Moore: For more than a decade since my February 1981 article on how to use modern metric, which SME-AIME had decided to do, I have monthly pointed out metric errors to the editors. In part, I do this because there has been no action to allow editors to fix figures and tables or to allow them to require authors to do so. The latest resulting atrocity provokes this discussion of vibrating drill handle units being stated in decibels. Reply by T. Moore We have read the discussion of our paper by Mr. Dasher. Our reaction is one of surprise and incredulity. It would seem that Mr. Dasher takes exception to the use of the decibel scale to present vibration acceleration data, and the use of hertz as the unit for frequency. The basis for his objection to the decibel appears to be that it has no dimensions (which somehow invalidates its use), that it is "non-metric" and, finally, that it is parochial (of limited or narrow scope). His objection to the use of the term hertz is not stated, but we will assume that it stands condemned as "non-metric" and parochial. Obviously we disagree with Mr. Dasher's views and will now outline our reasons. Although the decibel scale originates from transmission line theory and telephone engineering, it is also at present widely used, not only in the fields of electronic engineering and acoustics, but also in the area of vibration. The original definition of the decibel (dB) was based on power ratios: dB = 10 log 10(W/W0) where Wo is a reference power. However, as the power measured across a given impedance is related to the square of the force acting upon this impedance, Z, a more commonly used definition is: [2 dB = 10 logF /Z) = 20 log F/F 10\ F0 2 /Z(0)] where F and F0 are the r.m.s. values of the forces. Now, if the measurements are related to one and the same impedance, the decibel notation in the form of 20log10(X/Xo) may be used as a convenient relative magnitude scale for a variety of quantities. Thus, X may, for instance, be an r.m.s. displacement, velocity or acceleration. It is only required that XD always be a reference quantity of the same type as X. That is, when X represents an acceleration, then X0 represents a reference acceleration. This is the formulation used in our paper. This was not an arbitrary choice on our behalf but reflects standard practice as specified in the International Standard ISO 5349-1986(E) Mechanical Vibration - Guidelines for the Measurement and the Assessment of Human Despite the metric prefix, the decibel is a parochial expression of (l) the logarithmic ratio of the loudness of a sound to what is normally audible or (2) the logarithmic ratio of two power signals in radio or electronics. A decibel is not a unit, much less an SI, unit and has nothing whatsoever to do with the acceleration of drill handles. Stating that m/s2 (acceleration) is decibels is without reason. Whoever reviewed this material should not have allowed publication of figures of dB and H.[ ] Exposure to Hand-Transmitted Vibration. This was clearly stated in the "measurement protocol" section of our paper. This quantity is then referred to as the acceleration level and is expressed in dB. We may have inadvertently caused some confusion when we simply used the term acceleration to refer to acceleration level on our diagrams. At the time, we felt the use of dB or m/s2 would make the context clear to the reader. For any confusion this decision may have engendered, we apologize. Since the decibel expresses the ratio of two like quantities, it certainly has no dimensions. It is, however, common practice to treat "decibel" as a unit as, for example, in the sentence, "The acceleration level measured at the operator's hand was 160 dB." The expression of measured quantities in dimensionless form is not inherently unacceptable. In fact, in many areas of engineering it is standard practice (consider the use of Reynolds Number, Nusselt Number, etc.). The fact that the decibel is a dimensionless quantity makes the question of whether it is a SI unit nonsensical. However, it is valid to insist that the dimensional quantities used to obtain the decibel values be expressed in SI units. A careful reading of our paper will make it clear that the measured acceleration was, in fact, expressed in units of m/s2 as was the reference acceleration (l x 10-6 m/S2). These are the accepted derived SI units for acceleration. See, for example, the standard ASTM E380-89a Standard Practice for Use of the International System of Units (SI) (The Modernized Metric System). Concerning Mr. Dasher's implication that hertz (Hz) is an unacceptable unit of measure for frequency, we would again refer him to the standard ASTM E380-89a. Here, he will find (section 2.4.2) that hertz is an accepted "special name" for the derived SI units-1. This is in keeping with numerous other international standards including ISO 5349-1986(E) to which we referred in our paper. In conclusion, we agree with Mr. Dasher on the desirability of expressing measurements in modern SI units. But we would remind him that the standards that define the use of these units, and the accepted means of presenting measured data, are in a continual state of refinement. It is, therefore, incumbent upon him to keep abreast of these changes if he wishes to constructively critique the work of others.[ ]

Jan 1, 1992

By C. F. Allen, G. B. Walker

K. F. TROMP*—In dealing with the question of the most suitable kind of solid media for heavy density suspension processes Walker and Allen point out that the particle size of the solid media should not be taken too fine, as the viscosity increases with the area of the solid media and a low viscosity is essential lor high tonnage and accurate separation. A coarser particle size of the solid media will, in their opinion, of necessity give rise to a differential density in the bath (higher gravity at the bottom of the bath than at the top) but they advocate acceptance of the differential density rather than a higher viscosity. Though I fully agree with the choice the authors have made, I cannot subscribe to their view that only by accepting a differential density in the bath a coarse particle size of the solid media can be used. There certainly is another alternative: stronger agitation. Applying sufficiently strong vertical currents, a uniform gravity can be obtained quite well in a suspension of a coarse solid media. Of course, this is not a very attractive solution, for it means a degradation of the true gravity separation and a step backwards to hydraulic classification, which makes the washing dependent on size and shape of the particles. However, to a greater or lesser extent, this is what actually takes place in all the heavy density suspension processes relying on a uniform gravity in the bath. The so-called "stable" suspension processes make no exception. They all "stabilize" their suspensions by introducing or creating vertical currents, be it upwards or downwards or both, be it by hydraulic or by mechanical means. In fact, there is no such thing as a "stable" suspension in gravity separation, as the very reason for the use of suspensions in this field is the property that the solid media is able to settle and so facilitate the recovery. I have been enlarging on this point because the characteristics of the various processes can only be well understood and viewed from the same angle (from Bar-voys up to Chance) when the fact is recognized that mechanical or hydraulic agitation is a condition sine qua non for obtaining a uniform density from top to bottom in a suspension. Is a Cone-slraped Vessel Essenlial? Of the two alternatives for getting a low viscosity Walker and Allen have preferred correctly the sacrifice of uniform gravity in the bath instead of increasing further their vertical current arid agitation. The resulting differential density of the bath brings the problem of bow to prevent accumulation of intermediate gravity products in the bath, an accumulation which, if not prevented, would ultimately plug their cone. According to the authors an open-top cone combined with a downdraft current of the bath liquid would he the only suitable way to cope with such suspensions and they assume as a fact that "in any vessel other than a cone, such a differential density could not be tolerated." My experience is quilt: different. In my process, which has been in successful operation for more than a decade, differ-ential density of the suspension is applied ranging from values below 0.1 up to differentials above 0.5, according to the prevailing requirements of the individual plant. In this process, which is charac-terized by the use of horizontal currents in a suspension of differential density, the form of the vessel is of secondary importance and different types are in operation. It so happens that none of these are in the, form of a cone. The fact that 24 washboxes on my process have been installed and 12 others are under construction may constitute sufficient proof against the opinion that only a cone-shaped separator would be suited for differential density separation. Horizontal Currents in Differentia1 Den-sity Sepparation I myself have some doubts as to the suitability of a cone with downdraft for dealing with differential density (or, for that matter, any other washbox relying on vertical currents for removing the intermediate gravity products). It ap-pears to me that it is restricted to feed of small size only and even then with watch-fulness. If we take, for example, a piece of 2 in., the draft necessary to pull such a piece down to a zone wherein the den-sity of the suspension is, say, 0.03 higher, is quite considerable. For a suspension of, say, 1.6 sp gr the downdraft will have to be in the region of 3 in. per second. Unfortunately. most of the differential in density is in the part immediately below the reach of the top current which transports the floats. Consequently, we need the downdraft where we like it least: in the upper part of the cone. This entails the risk that light float particles are carried away with the downward current. This current of, say again, 3 in. per second would carry particles up to 1.3 sp gr and 3/8 in. size into the 1.6 gravity zone. This is prohibitive. It is also prohibitive because a downdraft of 3 in. per second in the upper part of the cone would require a tremendous circulation of medium. IIalf way up a 20 ft diam cone, a downdraft of 3 in. per second would correspond with 8500 gpm. With the downward current following the way of least resistance, the strength of the downdraft will not be exactly the same at different places of a cross area. If, as I anticipate, the center of the cone is favored, the strength of the downdraft will fall below the critical value near the

Jan 1, 1950

By R. R. Klimpel

Introduction The grinding of coal-water slurries has received increasing industrial attention during the last decade. In particular, there is long-term interest in the use of pulverized coal-water slurries to replace oil in combustion equipment and in the development of coal gasification/liquefaction processes that require coal-water slurries as feed. More specifically, the use of coal-water slurries in gasification requires grinding a high-density slurry containing the smallest amount of water consistent with slurry pumping and spraying. As part of a fundamental engineering research support program aimed at the industrial implementation of dense coal-water slurry grinding, this author has published several papers on how specific rates of breakage vary as a function of slurry rheology (Klimpel, 1982,1982/83). These papers demonstrated that there is a consistent pattern of change in specific rates of breakage of coal in dense slurries with controlled variation in slurry rheology. By matching rheological data with laboratory grinding results, it was possible to identify directly slurry conditions that correspond to: 1) slowing down of breakage rates, 2) the occasional acceleration of breakage of some sizes, and 3) conditions where chemical additives will increase rates of breakage. In brief, these conditions were analyzed using two different criteria: a) the net production rate of material less than some specified size (e.g. kg/min of minus 325 mesh) in a standard batch laboratory mill test as a function of controlled changes in grinding conditions, and b) the use of the one-size-fraction feed method, which consists of following the disappearance of this largest size over grinding time in a batch laboratory mill to arrive at well-known specific rates of breakage (Austin et al., 1984). Detailed references to the methodology used as well as the conclusions are available (Klimpel, 1982, 1982/83) and will not be repeated here. The purpose of this paper is to further demonstrate several additional characteristics of dense coal-water slurry grinding that were shown in a simplified sense in the earlier publications of the author but which have clearly demonstrated themselves as being very important in the industrial simulation and scale-up of such coal-water grinding systems. In particular, this includes the clear and unambiguous demonstration of how the simultaneous acceleration of breakage of some size fractions and slowing down of the breakage of other size fractions is occurring as a function of changes in coal-water slurry density. In the earlier publications (e.g. Klimpel, 1982), it was shown by specially designed experiments that the addition of fine material and/or the use of a chemical thickening agent accelerated the specific rates of breakage of coals of coarser size fractions using the one-size-fraction method. There were also numerous examples given of non first-order breakage (the slowing down of coal breakage rates) using also the one-size-fraction method due to the presence of excessive amounts of fines which corresponded to the development of a rheological yield value. The problem with the simulation and scale-up of any laboratory and/or pilot-scale mill data to an industrial scale using the mechanistic modelling approach involving specific rates of breakage and breakage distribution parameters (e.g. Austin et al., 1984) is the number of assumptions involved in translating the smaller mill breakage parameters to the predicted larger mill breakage parameters. It is apparent, at least to this author, that to accurately simulate and predict larger scale equipment performance from smaller scale data (given that the larger scale data performance is known and hence predictions can be thoroughly checked) requires a better knowledge of breakage parameters than is currently available. More specifically, it was felt that one of the chief problems was the inability of the one-size-fraction method of determining breakage parameters to sufficiently represent the actual magnitude and sometimes even the directions of. the complicated interactions involved with slurry density changes in coal-water slurry grinding. Thus, a special set of experiments was conducted in a somewhat larger batch ball mill (0.457 m diam x 0.610 m length) than the 0.203-m-diam mill used in the original rheology characterization paper (Klimpel, 1982) so as to minimize any unusual effects due to wall-ball interactions (2.54-cm-diam balls used in both mills). More importantly, the measurements of specific rates of breakage were done using a proprietary tracer method on a portion of a given size fraction, which was then remixed into a natural feed size distribution before grinding. The experimental procedure and analysis of subsequent data was done in exactly the same manner as the radioactive tracer technique on coals as originally developed by Gardner (1962). The advantage of such an approach is that it makes no assumptions such as the independence of the specific rate of breakage of any size on the absolute sizes and amounts of other sizes present (both larger and smaller) in the mix of natural feed material. It will be shown that the measured rates of breakage using the direct tracer technique and the one-size fraction method on the same coal are indeed different. In fact, an accurate assessment of what is happening to the rates of breakage as a function of changing slurry density can only he made by measuring particle breakage under grinding conditions approximating the size distributions actually being produced in practice. Experiment procedures and results The pilot mill used was 44 cm diam x 60 cm long with a volume of 91,250 cm3 and was fitted with six 0.5-in. lifter bars.

Jan 1, 1992