Search Documents

By Peter Zhang, Todd Minoski, Mark Van Dyke, Daniel W. H. Su

"This paper presents the results of a 2017 study conducted by the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Mining Research Division (PMRD), to evaluate the effects of longwall-induced subsurface deformations within a longwall abutment pillar under deep cover. The 2017 study was conducted in a southwestern Pennsylvania coal mine, which extracts 1,500-foot-wide longwall panels under 1,185 feet of cover. One 650-foot-deep, in-place inclinometer monitoring well was drilled and installed over a 150-foot by 275-foot center abutment pillar. In addition to the monitoring well, surface subsidence measurements and underground coal pillar pressure measurements were conducted as the 1,500-foot-wide longwall panel on the south side of the abutment pillar was being mined.Prior to the first longwall excavation, a number of simulations using FLAC3D™ (Itasca, 2017) were conducted to estimate surface subsidence, increases in underground coal pillar pressure, and subsurface horizontal displacements in the monitoring well. Comparisons of the pre-mining FLAC3D simulation results and the surface, subsurface, and underground instrumentation results show that the measured in-place inclinometer casing deformations are in reasonable agreement with those predicted by the 3D finite difference models. The measured surface subsidence and pillar pressure are in excellent agreement with those predicted by the 3D models. Results from this 2017 research clearly indicate that, under deep cover, the measured horizontal displacements within the abutment pillar are approximately one order of magnitude smaller than those measured in a 2014 study under medium cover.INTRODUCTIONDue to a recent shale gas boom, approximately 1,400 unconventional shale gas wells have been drilled through active and future coal reserves in Pennsylvania, West Virginia, and Ohio over the past 15 years. These shale gas wells have penetrated many coal seams, such as the Sewickley, Pittsburgh, Upper Freeport, and Kittanning seams. These unconventional gas wells, whether tapped into the Marcellus or Utica formations, contain very high gas pressure. Strata deformations associated with longwall and other high extraction techniques could induce high stresses and deformations in the shale gas well casings. This could seriously compromise the mechanical integrity of the production, intermediate, and coal protection casings (Figure 1). Damaged well casings could potentially introduce high-pressure, explosive gas into underground mine workings, particularly during an extended well shut-in period, which could seriously jeopardize underground miners’ safety and health."

Jan 1, 2018

By Richard E. Barrett

SOME YEARS AGO I was associated with a mining operation which, because of its isolated location, burned wood for heating purposes. Year after year the tractors and tucks hauled the cordwood in from the edge of the ever-growing clearing. Each year the cartage costs became greater. The degree to which transportation distances affect the economics of fuels obviously varies with many factors, but the main criterion is the amount of heat a unit weight of the fuel will produce. For in-stance, wood is limited in most cases to a haulage distance of a few miles. Coal can be shipped hundreds of miles, whereas petroleum and gas ?can be transported thousands of miles. The world is now on the brink of having a new fuel -uranium. It has the virtue of being so concentrated that transportation costs can, for all practical purposes, be disregarded.

Jan 1, 1958

By C. R. Hocott

"IntroductionRESEARCH in petroleum production consists primarily in investigations related to the drilling for and recovery of oil. As an organized activity of individual oil companies, production research is now 30 to 35 years old, and the petroleum industry may point with justifiable pride to the achievements of this third of a •century. Emphasis on research has grown through the years until at the present time many of the larger companies operating in the United States •have well-organized production research staffs.In addition to the efforts of the oil companies, significant research and development in petroleum production technology have been performed by oilfield service companies and others. Valuable contributions have been made through fundamental research carried on by the U. S. Bureau of Mines and by various colleges and universities, both in their own programmes and in programmes sponsored by industry, such as those of the American Petroleum Institute. However, the total effort of these groups is small when compared to the sum of the effort devoted to research by the individual .oil companies. In contrast to some industries which conduct the major portion of their research through co-operative, sponsored research at universities or research institutions, research by the petroleum industry is done predominantly by individual company research staffs. These industrial research groups have usually been organized in such a way as to provide liaison and co-ordination with operating technical staffs. In this way, the research groups are kept aware of the major problems confronting the operating departments and, correspondingly, the operating technical people •are able to keep informed on research activity and progress. This type of close contact generally results in prompt testing of research developments in actual operations."

Jan 1, 1953

By E. S. Moore

To properly understand industrial conditions in Spain it is necessary to consider the early history of the country. Spain is very backward in many lines. They use the sickle for cutting grain, and plows for cultivating the land, which resemble those of Biblical days. In the great mining camp at Bilbao only one steam-shovel is in use, although about two hundred million tons of ore has been produced, and this almost entirely from open cuts. It is the lack of industrial development, such as is found in many other countries, which permits large mining enterprises to be controlled almost entirely by foreign capital, although Spain is such an old country, and which permits mines opened in the days of the Phoenicians to still operate. Such deposits in America would be exhausted in a comparatively few years. The Phoenicians are supposed to have reached Spain about 1100 B.C. and to have worked some of the properties in the Rio Tinto district. The Carthagenians invaded the country about 236 B.C., and they were driven out about 205 B.C. by the Romans. The Romans ruled until 483 A.D., when they were overthrown by the Visigoths. Then, about 711 A.D., the Moors from Africa became prominent and they were finally expelled by the Spaniards in 1492. Spanish power reached its zenith under Phillip II, during the latter half of the 16th century, and since the close of that century the country has lost its prominent place among the nations. There are some evidences of revival in the development of good roads, the construction of a satisfactory network of railways, and the building of magnificent thoroughfares through the capital city, Madrid.

Jan 1, 1927

By A. J. Basu

Computer assisted mine planning and design applications are routinely used by many Australian mining companies, However, the design process requires human expertise to recognize and evaluate the potential pitfalls. This paper introduces the application of a commercial optimization software (WHITTLE 4D) for strategic planning of an open pit mine in Western Australia. The authors present their experience in intelligent application of the optimization program while incorporating many technical and nontechnical obstacles. This paper provides some guidelines on how to apply the optimization software without loosing sight of practicalities. Moreover, this paper also shows how to build project evaluation guidelines for non-experts.

Jan 1, 1997

Visual computing opens the design process to a wider audience and allows rapid communication of mine plans to all stakeholders. The integration of software and hardware technologies that take advantage of a graphical environment will continue to improve both long-term and short-term mine design (Figure 1). A good design must be adaptive to respond to decision changes as the mine develops and more information becomes available. The constraints on mine design predicate careful analysis in order to operate the mine as efficiently and safely as possible.Continuous improvement in mining is assured by developing innovative technologies that target mine survey, drill and blast, modelling, short-term design and pit and stope optimisers. The design life of a mine has to be sufficiently long to ensure the mine is commercially successful, justifying the high start-up capital costs. Being able to execute a plan so that it honours the design realises the rewards of computerised mine planning and the long-term investment in data acquisition.

Sep 26, 2011

By T. B. Williams

THE British Columbia Coal Control was established in 1946 as a branch of the Department of Lands. Its functions are the administration of the Goal Act, the making of field and laboratory investigations bearing on the delineation and utilization of British Columbia coal deposits, and the dissemination of information concerning them. The Department of Lands in the Province of British Columbia retains and administers many of the Province's resources until such time as they are actively developed under the departments of Agriculture, of Forests, of Mines, etcc. The work of the Control is one of stock taking and appraising. We are picking up where the geological surveys leave off. In an effort to assist in the orderly, scientific development -of our excellent and extensive' ?Coat resources, we are bridging the gap between exploration and geological examination on the -one hand and mining on the other. All coal analyses required in the course of the investigations, together with? those requested by prospectors and others, are carried out in the very modern and efficient laboratories of the Coal, Petroleum, and Natural Gas Control. At its inception, the Coal Control began an investigation of coal seams in the Peace River area, specifically those contiguous to the Pine River valley about one hundred miles west of Dawson Creek. The occurrence of coal in the Peace River canyon, east of Hudson's Hope, bad been known since 1792, but the first record of production is for 1923.

Jan 1, 1951

By P. K. Songfack

The transport of slurry within the ball mill depends on the peripheral velocity and porosity of the ball charge. Residence time distribution and mill hold up are of-ten used as indicators of the mode of transport. In this work, the transport problem is tackled via direct simulation of the three dimensional motion of the ball charge. In doing so, the following quantities are calculated: (i) ball size distribution as a function of the distance from the feed end of the mill (ii) mean peripheral and longitudinal velocity and longitudinal velocity of balls of different sizes, and (iii) the spatial distribution of porosity within the ball charge. Hence, the problem of transport is handled as a motion of part of the slurry with the ball charge and part as hydrodynamic flow through the porous structure.

Jan 1, 1993

By G Wyartt

In the Pilbara region of Western Australia, an iron ore mine is undertaking a high wall cut-back to improve stability and allow access to deeper ore deposits. Several sections of the wall have been classified low factor-of-safety due to unstable localised geology, and therefore an engineered approach to vibration critical blasting was required. The use of electronic detonators allowed multiple signature (seed) holes to be incorporated into a production blast adjacent to the low factor-of-safety area, therefore providing baseline vibration data to be used for future modelling with the added advantage of eliminating unnecessary pit closure downtime typically associated with a signature hole program. All subsequent blast patterns also incorporated multiple signature holes to provide additional data and allow continual updating – and therefore improved accuracy - of the blast prediction model. Electronic detonators and blast initiation systems were combined with advanced blast vibration modelling software to produce optimal timing sequences with predictable vibration outcomes. Although minimising vibration was the primary focus, blasting induced frequency was also a concern for the project team and therefore initiation sequencing was optimised to also avoid undesirable frequencies. Minor variations in ground factors (vibration transmission and attenuation) were noted, and therefore justified the inclusion of regular signature holes which allowed continual vibration model updates. Blasting results produced vibration and frequency measurements within allowable limits and closely resembled the predictive model. These positive results were achievable through the combination of electronic detonators, advanced modelling software and good onsite practices by engineering and on-bench teams alike. This project will remain ongoing as the pit progresses to deeper benches, and therefore the same methodology will be applied; quality and continual data collection, the use of electronic detonators, and optimisation via advanced vibration and frequency modelling software. CITATION:Wyartt, G, 2018. Vibration control blasting for low stability final walls, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 504–510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By B. T. Darnton

Gravity concentration at the Pegasus Gold Montana Tunnels Mine was initiated in late June, 1991 with the commissioning of a coarse gold scalping circuit that processes a small portion of the ball mill circulating load. The primary objective for the circuit was to reduce the risk of gold particles advancing to flotation that are too coarse to float. The secondary objective was to enhance overall gold recovery and payable gold ounces in a cost effective manner. The gravity circuit has proven itself to be a major success. The above mentioned goals have been achieved, and they have been maintained at record throughput rates that are 30% higher than when the circuit was commissioned. A number of modifications and improvements were made over the last three years which allowed the gravity circuit to keep pace with the higher tonnage, these are discussed in detail in the body of this paper. The overall approach to gravity concentration at Montana Tunnels has always been to optimize production rather than maximize the gold ounces produced. This philosophy has now yielded a circuit expansion and relocation project which will allow for an estimated 50% increase in gravity gold production, while reducing the overall unit costs of production significantly. This paper will review historical gravity circuit performance, improvements, and the current relocation and expansion project.

Jan 1, 1995

By S. K. Kawatra, T. C. Eisele

"Recent advances in microbiology have made the application of biotechnology to metallurgical processes possible. Hydrometallurgy stands to gain the cost from the use of microorganisms, as they are useful for both dissolution aids and for removing metals from solution. The development of genetic engineering techniques promises to greatly increase the importance of bioprocessing of metals and minerals by the year 2000.In this paper, the basic effects of microorganisms on metallurgical processes are reviewed, and the applications which are currently either in use or near being used are presented. Representative data collected at Michigan Technological University is also given.IntroductionMany hydrometallurgical operations exist which are thermodynamically possible, but which are industrially impractical due to slow kinetics, high reagent costs, or the need for a highly corrosive environment. However, recent discoveries in microbiology indicate that in many cases these difficulties can be reduced greatly by the action of bacteria and other microorganisms (1-8).A major advantage of using living organisms in hydrometallurgy is that once the culture is established the microorganisms produce their own reagents either from the material being processed or from low-cost nutrient supplements. They thus allow extremely complex chemical reactions to be carried out at reasonable cost. The major drawback of using microorganisms is their inability to tolerate extremely high temperatures, excessive concentrations of toxic metals, or very highly acidic, alkaline, or corrosive conditions. However, the complex reactions which bacteria make possible frequently eliminate the need for such extreme conditions. Also, in recent years a number of organisms have been isolated from such exotic environments as hot springs and deep-ocean vents which can tolerate temperatures higher than was previously thought possible for any organism, and can catalyze a number of metallurgically important reactions (8)."

Jan 1, 1988

By Valerio Violo, Antonio Raschillà, Livia Cicinelli

"The Cityringen project foresees the construction of a new circular metro line in and around the city center of Copenhagen. Both drives, the north and the south one, required the TBMs to be equipped in order to cope with contaminated water table and soil. The north drive mined in water contaminated with chlorinated compounds, including chloroform and vinyl chloride, while the south TBMs excavated in a highly benzene contaminated area, becoming the first TBMs to complete such a challenge. Despite the pollution and the stricter operative procedures, the production has been extremely successful with record up to 520 m in one month and 32 m in one day. 1 INTRODUCTION The Cityringen is an extension of the existing metro line. The 15 km long twin tunnels will form a new circular line with 21 new stations (17 + 4 crossovers). When finished it will interchange with the existing metro, rail and bus infrastructure at key locations around town, taking 90% of Copenhagen citizen at less the 600m from a metro station (Figure 1). The Contract has been awarded in April 2011 to the Copenhagen Metro Team (CMT), a joint venture between the Italian companies Salini Impregilo, Tecnimont and Seli SpA. Tunnels are being excavated with 4 Seli-Kawasaki EPB TBMs, two of which manufactured in Denmark by Seli Tunneling Denmark ApS, which is also operating them. At the moment this article is written 50% of the tunnels have been completed and over 40% handed over for the electromechanical works. Seli Tunnelling Denmark is a Danish company constituted in 2012 as a subsidiary of Seli SpA for this project and subsequently acquired by the Salini Impregilo Group in 2015."

Jan 1, 2016

By A. L. Engel

This report is a compilation of preliminary and, in some cases, more extensive concentration experiments by the Federal Bureau of Mines on low-and medium-grade fluorspar ores from three localities in Nevada and one in California. The work was done on samples obtained from Shoshone mine, Nye County, Valery mine, Pershing County, and the Broken Hills mine, Mineral County, all in Nevada, and Dirty Weather mine, Inyo County, Calif. These investigations were made to aid in the development of domestic fluorspar resources, in line with the Bureau's long-established program of conservation of mineral resources. The treatment methods employed in the experimental work described included simulated or "heavy-liquid" gravity concentration of coarse minerals and comparatively fine-grained minerals, and flotation concentration of finely-ground minerals. These methods were attempted in order to beneficiate the ores and produce concentrates which could be marketed readily, with as high a recovery rate as possible, while using simple treatment methods suitable for small-scale operation.

Jan 1, 1961

By W. Hunka

PACIFIC PETROLEUMS, Ltd. first discovered commercial quantities of gas in the Peace River area in 1952. Development of gas wells in this area is quite ex-pensive due to low penetration rates. To improve the economics, the potential of the wells in many cases had to be increased. At that time, well stimulation was still in its infancy in Canada and in this area, in particular, no treatment of any consequence had been attempted. Therefore, trial-and-error was the only means available to determine the stimulating technique that would give optimum results. Various fluid treatments were available and these were used wherever the application was warrant-ed. This paper covers acid fracture and explosive treatments as carried out on various gas-bearing horizons.

Jan 1, 1958

By C. R. Tinsley

Valuations can be molded, twisted and misinterpreted. Cases of spurious scope setting; limits to the information or access by the valuer; difficulties with the lack of comparative valuations; inappropriate valuation methods and outright speculations are described. None should be accepted by an experienced, independent minerals valuer. The Australasian Institute of Mining and Metallurgy (TheAusIMM) is working on a Valmin Code for which a Manual of Best Practice and Valuation Guidelines may be developed.

Jan 1, 1995

By R. Lepsoe

THE basic products of the Company are lead and zinc. Around 950 tons of these metals are produced each day. In the last decade, the production of by-products has increased to such an extent that they are now nearly as large an operation as that of the base-metals. Of the many by-products, the most objectionable, and up to a few years ago the most useless, was the sulphur. The sulphur comes in the ore from the Sullivan mine. It is in the ore chiefly as lead, zinc, and iron sulphide. By selective flotation, these three sulphides are separated into the lead concentrates, the zinc concentrates, and the mill tailings. These mill tailings contain the bulk of the iron and the sulphur. Of the 6,5CO tons of ore treated per day, about 5,000 tons are wasted to the mill tailings dump, and, while now valueless, will in future years undoubtedly be used as a source of iron and sulphur. There are about 1,500 tons of sulphur and 2,200 tons of iron per day in the tailings, and about 400 tons of sulphur left in the total concentrates. In the recovery of lead and zinc in the pure form, the first step is the roasting operation. Here, most of the sulphur is driven off as sulphur dioxide in the gases. It has always been apparent that this sulphur should be. recovered and utilized if possible. At the same time, this would cure the smoke nuisance. Because, in spite of the low concentration of sulphur dioxide and the fact that it was discharged from stacks at an elevation of 400 feet above the plant, some damage to vegetation close to the plant had been experienced.

Jan 1, 1937

By Peter K. Kaiser

Planning and design of deep underground mines involves a process of complex three-dimensional data integration utilizing information from exploration (geology, rock mass characteristics), engineering (mining method, excavation geometry, stress) and operations (time, in the form of sequencing). As new logging and monitoring technologies are being developed, the amount and data complexity becomes overwhelming and decisions are often made based on only a small part of the available data. Recently, Laurentian University opened a state-of-the-art Virtual Reality Laboratory (VRL), a Mining Exploratorium that is unique in the world of mining and offers an exceptional data interpretation environment for mine planning and design. The Mining Exploratorium combines a large format spherical stereoscopic projection system, equipped with high definition projection providing the highest resolution of active stereo in the world today, with advanced features of earth modeling software. Combined, this creates the first virtual reality facility geared specifically to the interpretation of mine geometry, geology, geochemistry, microseismicity, geomechanics and mining data sets. This paper demonstrates how value can be added to the mine planning and design process by utilizing this unique tool in the mining decision-making process via better comprehension of spatial relationships of data and by interpreting the data in a collaborative immersive virtual reality environment.

May 1, 2002

By J. P. Wilson

The Tessenderlo-Kerley Leach process has been shown to be effective in the removal of residual copper from molybdenite concentrates. Concentrates of varying mineralogy, including those containing relatively large amounts of chalcopyrite, have been successfully leached on laboratory and pilot plant scales. The lixiviant system is ammonia and ammonium bisulfite with air / oxygen addition. An abrasive is added which greatly enhances the kinetics, and it is subsequently screened out and reused. The dissolved copper is easily recovered using existing technology. Extraction profiles, reagent consumptions, and mineralogical data are presented.

Jan 1, 1999

By W. J. Wright

Summary Statement The following notes on the geology of the Grand Lake coalfield are intended to be introductory to a second paper being read at this meeting, which paper will describe the earlier and the more modern mining methods. The coal industry of the Grand Lake coalfield is centred chiefly within a three-mile radius of Minto, but minor operations are dotted over an area of approximately 50 square miles extending easterly to the vicinity of Chipman and Coal Creek (see Figure 1). The coal comes from one seam of Pennsylvanian age. The seam varies in thickness from 16 to 30 inches and lies almost horizontal at depths of 0 to 125 feet. It has been mined and prospected over an area of approximately 150 square miles, but in a portion of this area the commercial possibilities have been destroyed by erosion. The industry is the oldest of its kind in North America, but it did not at tract particular publicity until about 1914. Since that date, mining methods have improved and the output has rapidly increased until, in 1934, it amounted to 271,335 long tons, and furnished employment for about 1,000 men (1). Approximately 73 percent of this amount was produced by the Minto Coal Company, the Miramichi Lumber Company, the Avon Coal Company, and Welton and Henderson, and 25 per cent by the Rothwell Coal Company, Harvey Welton Limited, G. H. King, the Reade Construction Company, and the Newcastle Coal Company. The remainder was produced by J. W. Carter, G. D. Crossman, T. H. Swift, C. S. Yeamans, and several other small operators. The coal is won by underground mining, except in the case of the Reade Construction Company, and a minor operation by Ashfield and Pieton, who have employed open stripping. It is mined only as required to fill definite orders, and is loaded directly into cars for shipment. In 1934, the larger mines did not operate full time, and the production could easily have been increased if markets had been available. The coal is sold in four grades: screened or lump, run of mine, slack, and stripping. The chief market is with the railways and commercial plants, with a fair amount for domestic purposes.

Jan 1, 1935

By Mario Alejandro Bendezú

En el presente artículo se analizan los factores esenciales para desarrollar un proyecto minero de uranio y litio en Perú. Luego de describir los requerimientos y perfil que debe tener la empresa minera a cargo —en este caso, una minera junior—, se revisan las implicancias operacionales, legales, económicas, sociales y ambientales del hecho de que los yacimientos contengan minerales radioactivos.

Nov 30, 2018