Search Documents

By J. B. Gayle

The rate of oxidation of coals with nitric acid has been used by earlier investigators4 5 6/ for determining fusain and for studying petrographic composition. These workers accumulated considerable evidence indicating that, for coals ranging from lignite to low-volatile in rank, the method gives values for fusain that agree satisfactorily with those obtained by optical methods. One group5/even concluded that, when discrepancies are noted between results obtained by chemical and microscopic methods, the results based on the oxidation reaction are probably the more reliable. Unfortunately, after concluding that the method was valid, most of these workers apparently lost interest. As a result, no attempt to exploit or apply the method to problems of utilization has been reported. Recent studies of the influence of inert petrographic constituents on the properties of cokes made from various coals7/ have indicated a need for additional means of characterizing coals and blends used for carbonization.

Jan 1, 1960

By J. Peterson

A review of blast designs and improved blasting practices at the Ekati??Diamond Mine is presented along with the results of three blast-monitoring experiments. Blast monitoring was undertaken to investigate blast damage mechanisms in the mine's well jointed rock mass. Rock mass damage caused by production, pre-shear and wall control blasts was measured. Ekati??uses 270mm holes for production blasting, and 165mm holes loaded with a decoupled charge for pre-shearing. The production blasts are loaded with bulk emulsion / ANFO blends. The mine plan involves using 30m double benches. A 30m high pre-shear is drilled and blasted prior to the production blasting that is done with sequential 15m benches. This paper summarizes the monitoring equipment and data gathered to date.

May 1, 2001

By Thomas H. Dubaniewicz

(XP) enclosures to enclose electrical ignition sources to prevent propagation of an internal methane-air explosion to a surrounding explosive atmosphere. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a lithium-ion battery thermal runaway test within a modified MSHA-approved XP enclosure to assess thermal runaway containment. Thermal runaway produced jet flames emanating from the cover joint at several locations and distorted the cover joint and bottom plate of the enclosure beyond allowable limits. The test demonstrates that XP enclosures may not provide adequate explosion protection against lithium-ion battery thermal runaway. This paper suggests some approaches to mitigate the hazard.

Feb 1, 2024

By Phillip Crowson

The annual surveys of corporate exploration expenditures carried out by Metals Economics Group (MEG) show that estimated total spending rose to a record $13.2 billion in 2008 ($14.4 billion including expenditure on uranium exploration). This compares with the previous peak of $5.2 billion in 1997. MEG does not adjust its figures for the effects of inflation but recognizes that the substantial increase in budgets of recent years has not been reflected in a proportionate rise in actual activity on the ground (MEG, 2009). In recent years, costs were boosted by rising prices of fuel and other inputs, and acute shortages of qualified staff and drilling rigs. The inflation rate for exploration substantially exceeded increases in general price levels as measured by national indices. Just how much exploration costs in-creased, however, is probably not widely appreciated. Figure 1 compares the MEG estimates of total annual dollar spending in Australia, Canada and the United States combined with their drilling activity, measured in meters drilled, as reported by national agencies. These three countries accounted for 39 percent of MEG?s estimate of total spending on minerals exploration in 2007 and 40 percent in 2008. Expenditure is shown both in money terms, as reported by MEG, and adjusted to real terms, with the U.S. implicit gross domestic product (GDP) price deflator. The comparison is of index numbers based on 2000 as 100. Comparisons for the individual countries are shown in Fig. 2 to 4. National figures for drilling activity and expenditures cover some minerals like iron ore, coal and industrial minerals (29 percent of Australian spending in 2007 to 2008 and 10 percent of Canadian in 2008) that are not included in the MEG estimates of spending. Such exploration has risen more than the total since 1997 so that the index of drilling activity in the figure may be overstated for recent years on a like for like basis with the MEG data. MEG only includes spending on uranium exploration in recent years whereas the national agencies include it throughout. Figures 5 and 6 com-pare national and MEG estimates for Australia and Canada. No comparable figures are available for the United States. The national estimates have been converted to U.S. dollars at the appropriate annual average exchange rates, and the Australian annual totals have been summed from the published quarterly data. Not only is spending cyclical, but so are unit costs. Australian and Canadian data show that total exploration spending per meter drilled rose by 2.5 to 3 times between 2001 and 2008. These rises may partly reflect increasingly complex drilling methods, and an increased share of assaying and testing in total exploration costs. In Canada, however, diamond drilling accounted for a lower footage of the total in 2005-2007 than in the preceding few years, and spending on exploration, as opposed to deposit appraisal, made up a higher proportion of the total. Figure 7 compares index numbers of exploration spending per meter drilled in U.S. dollars for Australia and Canada. These figures raise a number of questions. First, is the relationship between total expenditure and meters drilled in the three countries for which data are available typical of the global experience? Secondly, has there been a significant change in the make-up of exploration spending in recent years? The Canadian data do not suggest that there has been, but is Canada typical? Has drilling become less important relative to other exploration techniques, or is it just as important as ever in confirming the existence of viable ore deposits?

Jan 1, 2009

By J. Brian Eby

The Gulf Coast of southern Louisiana during the year of 1940 was subjected to an extensive exploration and development campaign, as a result of which 16 oil fields and about 38 new producing sands were found. Although this record of discovery appears in keeping with the rate of 1939 actually in amount of new proven reserves, it may fall short of that of the previous year. Only five or six of the discoveries rated as first-class or important fields at the close of the year. The most prominent new fields opened during the year were Neale field in Beaure-gard Parish, the West Cote Blanche field in St. Mary Parish, the Stella field and the West Bay field in Plaquemines Parish, and the Lake Salvador field in St. Charles Parish. There were many important oil-sand discoveries in proven fields, such as in the Bayou Perot field, the Golden Meadows field, the Iowa field, West Lake Verrett field, and the Venice field. During the year, 1047 weUs were drilled in southern Louisiana, of which 768 were completed as oil-producing wells, 17 as gas wells and 262 as dry holes. The Neale field in northwest Beauregard Parish is considered one of the most important discoveries of the year. The f~eld centers around the north half of sec. 26, 'Y.3 S., R.I I W., just north of the town of Neale. It was discovered by the Atlantic Refining Co., using reflection seismograph to locate the structure. Production was found in the second well drilled in the Wilcox sand on the downthrown side of a fault. The structure is known as the "Tepetate" type, being similar to that of the well-known Tepetate field. There were 12 oil wells and 3 dry holes drilled during the year. The Wilcox sand in this field occurs between 8350 and 8400 ft. and averages 30 ft. in thickness. The West Cote Blanche Bay field, in West Cote Blanche Bay, St. Mary Parish, is a 1940 discovery by the Texas Company, credited to reflection seismograph exploration. The oil is from two sands occurring at 3110 to 3140 ft. and from 4950 to 5020 it. Four wells were drilled during the year, three oil wells and one dry hole. The deepest hole drilled reached 9491 ft. without encountering salt or dome material. In Plaquemines Parish, south of New Orleans, the California company has a new field known as the Stella field. The sand was found at a depth of 7485 ft., and 5 ft. of perforations made a well capable of producing 486 bbl. of oil in 24 hr. through a 9.is-in. choke. The oil is 42" gravity. The discovery well was drilled to a total depth of 10,258 ft. and other producing sands were indicated. A good field appears assured, although only one well was completed within the year. The Lake Salvador field, in the center of Lake Salvador, St. Charles Parish, gives promise of being one of the most important discoveries of the year. The discovery well was perforated at 9775 to 9800 ft. making 850 bbl. of 33.7° gravity oil daily through a 1/4-in. choke. Three wells were completed in 1940 but few details have as yet been made available.he Gulf Oil Corporation apparently has a good field in its wildcat discovery in West Bay, Plaquemines Parish. This well found

Jan 1, 1941

By J. Brian Eby

The Gulf Coast of southern Louisiana during the year of 1940 was subjected to an extensive exploration and development campaign, as a result of which 16 oil fields and about 38 new producing sands were found. Although this record of discovery appears in keeping with the rate of 1939 actually in amount of new proven reserves, it may fall short of that of the previous year. Only five or six of the discoveries rated as first-class or important fields at the close of the year. The most prominent new fields opened during the year were Neale field in Beaure-gard Parish, the West Cote Blanche field in St. Mary Parish, the Stella field and the West Bay field in Plaquemines Parish, and the Lake Salvador field in St. Charles Parish. There were many important oil-sand discoveries in proven fields, such as in the Bayou Perot field, the Golden Meadows field, the Iowa field, West Lake Verrett field, and the Venice field. During the year, 1047 weUs were drilled in southern Louisiana, of which 768 were completed as oil-producing wells, 17 as gas wells and 262 as dry holes. The Neale field in northwest Beauregard Parish is considered one of the most important discoveries of the year. The f~eld centers around the north half of sec. 26, 'Y.3 S., R.I I W., just north of the town of Neale. It was discovered by the Atlantic Refining Co., using reflection seismograph to locate the structure. Production was found in the second well drilled in the Wilcox sand on the downthrown side of a fault. The structure is known as the "Tepetate" type, being similar to that of the well-known Tepetate field. There were 12 oil wells and 3 dry holes drilled during the year. The Wilcox sand in this field occurs between 8350 and 8400 ft. and averages 30 ft. in thickness. The West Cote Blanche Bay field, in West Cote Blanche Bay, St. Mary Parish, is a 1940 discovery by the Texas Company, credited to reflection seismograph exploration. The oil is from two sands occurring at 3110 to 3140 ft. and from 4950 to 5020 it. Four wells were drilled during the year, three oil wells and one dry hole. The deepest hole drilled reached 9491 ft. without encountering salt or dome material. In Plaquemines Parish, south of New Orleans, the California company has a new field known as the Stella field. The sand was found at a depth of 7485 ft., and 5 ft. of perforations made a well capable of producing 486 bbl. of oil in 24 hr. through a 9.is-in. choke. The oil is 42" gravity. The discovery well was drilled to a total depth of 10,258 ft. and other producing sands were indicated. A good field appears assured, although only one well was completed within the year. The Lake Salvador field, in the center of Lake Salvador, St. Charles Parish, gives promise of being one of the most important discoveries of the year. The discovery well was perforated at 9775 to 9800 ft. making 850 bbl. of 33.7° gravity oil daily through a 1/4-in. choke. Three wells were completed in 1940 but few details have as yet been made available.he Gulf Oil Corporation apparently has a good field in its wildcat discovery in West Bay, Plaquemines Parish. This well found

Jan 1, 1941

By Alexander Karim

This paper reviews the growth pattern in bauxite and alumina production, and primary aluminum smelting through 1980. Because the alumina and primary metal are intermediate products of the major integrated aluminum companies, it is not possible to determine their production costs. The costs indicated in this paper are order of magnitude costs based on published figures and the market price of these products. The conclusions in this paper indicate the general pattern of growth in the aluminum industry and are not meant to be a substitute for the feasibility and economic studies that are needed for individual bauxite mining, alumina refining and aluminum smelting projects.

Jan 1, 1968

By N Gupta, R Trivedi, S Bhandari

Managing blasting operations in four mines surrounded by villages is a challenging task. This study aims to compare the blast-induced flyrock as observed in opencast mines by predicting flyrock distance using a soft computing approach known as an adaptive neuro-fuzzy inference system (ANFIS) and Flyrock Predictor software based on empirical studies. Blast design and geotechnical variables such as linear charge concentration, burden, stemming length, specific charge, unconfined compressive strength and rock quality designation were selected as independent variables, while flyrock distance was used as a dependent variable. Out of 120 blasts, data from 100 blasts was used to train and test the ANFIS model. Flyrock distance for the remaining 20 blasts was used to evaluate the model. Flyrock distance has also been predicted using Flyrock Predictor software based on an empirical approach using the same data sets as those used for ANFIS. Performance indices like root mean square error (RMSE), mean absolute error and coefficient of determination (R2) were evaluated to compare the reliability of ANFIS and Flyrock Predictor quantitatively. ANFIS was found to be a better predictive tool, with 1.75 m RMSE and 0.966 R2 compared to Flyrock Predictor, which returned RMSE and R2 values of 2.48 m and 0.932 respectively.CITATION:Trivedi, R, Singh, T N, Gupta, N and Bhandari, S, 2015. Soft computing approach to predict blast-induced flyrock, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 455–462 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Herbert H. Fields

The Bureau of Mines has been promoting health and safety in mining since its establishment in 1910. One area of research covers methane control in coalbeds; this report describes a multipurpose borehole used for both degasification and the production of commercial-quality gas. The multipurpose borehole was drilled into a barrier pillar, and seven horizontal degasification holes and one pressure point hole were drilled radially out from its perimeter. On January 28, 1974, after 505 days of degasification, a compressor was installed to the exhaust stack of the multipurpose borehole (1), and pipeline--quality gas was introduced into a commercial pipe-line. As of February 4, 1975, over 171 million cubic feet of gas had been purchased by the gas company. The in situ pressure at a depth of 200 feet into the coalbed and the average gas flow and water flow from the degasification holes as they were completed and closed off were 203 psig, 1,200,000 cfd, and 6.8 gpm, respectively. Twenty-four hours after the seven holes were connected through individual pipes to the atmosphere, the total gas and water flows and the in situ pressure dropped, respectively, to 971,000 cfd, 1.3 gpm, and 18 psig. Five hundred days later, the corresponding values were 620,000 cfd, 0.15 gpm, and 10.5 psig. Daily flows have been as high as 800,000 cfd, and as low as 360,000 cfd, during the last 500 days. On February 4, 1975, after 882 days of degasification, 576 million cubic feet of gas had been removed from the Pittsburgh coalbed; apparently a much larger area of virgin coal is being degasified than is defined by the holes. This study indicates that horizontal boreholes drilled into a coalbed from the bottom of any shaft will effectively remove gas from the Pittsburgh coalbed,

Jan 1, 1975

By N. Campbell, W. T. Orvine

The metalliferous deposits of British Columbia are largely confined to that portion of the Cordilleran province lying west of the Rocky Mountain trench. Massive sulphides in the coastal area carry important copper •values together with lead and zinc and are composed mainly of pyrite which replaces schists or shear zones. The massive sulphide ore of the interior, on the other hand, contains lead and zinc with little copper. Pyrrhotite rather than pyrite is... the dominant metallic and deposition took place through selective replacement of sedimentary beds.

Jan 1, 1960

By Thomas P. Meloy

"The presence of respirable quartz-bearing mineral par-ticles has been well documented in many coal mines, and the Mine Safety and Health Administration regulations address the quartz content of mine dusts. Unfortunately, the correlation between the quantity of respirable quartz-bearing mineral particles and the pathogenicity of the dust is not strong. Work is currently underway by the National Institute for Occupational Safety and Health/U.S. Bureau of Mines and work is being included in the Respirable Dust Center Program by Dr. Seehra to determine the surface availability of quartz in mixed composition mine dusts. However, this paper propose a possible source of surface quartz or a spe¬cial region in the coal that may contribute to the pathogenicity of selected particles in the respirable dust.Assumed in this model is the hypothesis that either the cleat surface is coated with quartz or some cytotoxic sub-stance that in the body is capable of destroying macrophage and thus inducing a fibrotic response (1) that during the frag¬mentation a reasonable proportion of the respirable size coal particles contain some of the original cleat surface and that these particles have the same order of in vivo cytotoxicity as do the quartz particles. It may be that these cleat surfaced respirable size particles are only contributory to the overall pathogenicity of the coal dust, nevertheless, there are enough of these particles to to considered as a potential source of the cytotoxic dust particles.This paper demonstrates that if the cleat surfaces are mineralized with quartz or have a pathogenic coating, then in many mines there will be enough respirable coal dust particles containing some cleat surface to cause a fibrotic reaction. To understand why some of the dust particles contain as part of their surface some of the cleat surface, consider what happens when a beer bottle is broken. While there are a large number of beer bottle fragments, many of the fragments, particularly the larger fragment sizes, will have as a fraction of their surface part of the original beer bottle surface. The model and mathematics of this problem have been worked out by Meloy.(2-4)In the homogeneous IAC model, (2-5) a fragment or par-ticle resulting from comminution is equally likely to occur anywhere in the material being broken. Therefore the probability of a particle of size x having part of the cleat surface in it, p(x), is proportional to x. Thus:"

Mar 1, 1989

By GERALD A. WARING

ALASKA'S coal consumption is now about 130,000 tons annually. About one-quarter of this amount is used in the southeastern part of the territory and in settlements on the western coast and comes from Seattle and from British Columbia mines. About 60,000 tons is sub-bituminous coal from the Healy River mine in central Alaska, and is used mainly at Fairbanks, sixty miles to the north, for heating and the development of electric energy, for the city and the gold-dredging operations of the Fairbanks Exploration Co. The remaining 40,000 or 50,000 tons is bituminous coal from Matanuska Valley, in the south-central part of the territory. These coal deposits extend intermittently for about forty miles along the valley, which trends eastward from the upper end of Cook Inlet.

Jan 1, 1934

By D. Foster Hewett

The scope of this paper is the description of two districts in Peru in which deposits of vanadium have been found, and the consideration of much laboratory-work that I and others have done to determine the nature of these deposits. It is with regret that I present some of the data in a state of evident incompletion, particularly the analyses of a few of the minerals, which leaves some doubt as to whether the true nature of the migerals is understood. I make no apology, however, since in this case, as in many others referring to ore-deposits, conclusive opinions cannot be stated until a great amount of work has been done, and the deposit has been thoroughly exploited. I believe that the data and the tentative conclusions here presented indicate a unique and interesting condition which may assist others in work along similar lines; arid further, what is of more practical importance, stimulate a search for a metal which, though long considered rare, is probably so merely because proper care has not been taken to recognize it. An excellent bibliography on the occurrence of vanadium in nature is given by I?. W. Clarke in his paper, Data of Geochemistry;' and in the preparation of this paper 1 have consulted many of the references contained in the Bibliography of the Chemistry of Vanadium, by M. Moisan.2 A brief review of the subject having special reference to the metallurgy of vanadium is contained in the small book by P. Nicolardot.3 One of these vanadium-deposits has already been briefly. 1 Bulletin No. 330, U. S. Geological Survey (1908). 2 Chimie Minerale, vol. iii. (1905). 3 Le Vanadium (1905).

Jan 1, 1910

By A. Matzick

In its work under the Synthetic Liquid Fuels Program the Bureau of Mines has developed on a 6-ton-a-day-pilot-plant scale a continuous, gravity-feed retort far distilling oil from oil shale. The development work covered by this report was done from January 27, 1950, to January 26, 1952, at the ail-Shale Experiment Station near Rifle, Colo. Over 300 pilot-plant tests were made during the investigation. The basic retort developed has been named the Gas-Combustion retort. In this process, part of the heat for retorting of the shale is generated by burning recycled product gas in a combustion zone within the descending shale bad in the retort. Additional heat is supplied by combustion of the carbonaceous residue remaining in the spent shale after the oil has been distilled. Air for combustion is admitted through an air distributor in the center of the bed at about the mid-point of the retort. Hot gas rising from the combustion zone heats countercurrently the descending raw shale and liberated shale oil by pyrolysis of the shale. After passing through and exchanging heat with the incoming raw shale, the oil is condensed as a fog or mist in the gas, which is withdrawn at the tip of the retort. The cool gas is then piped to an oil-recovery system where the oil is separated from the gas in centrifugal separators or other types of mechanical or electrostatic separators. The hot, spent shale below the combustion zone is cooled by heat exchange with recycle gas, which is a portion of the effluent gas from the oil-recovery system.

Jan 1, 1955

By D. A. Larson

This is the second in a series of Bureau of Mines reports which de-scribe experiments designed to devise an efficient, economic mechanical fragmentation technique for hard rock. The previous study described the development of the ripper cutting technique to successfully cut hard rock with 3-to 6-in-wide drag cutters. This study was conducted to test the ripper cutting technique at full scale using 9-in-wide drag cutters. The experiments were conducted with a special test device that cut shallow, 6-by 6-ft openings in 9,200-lbf/in2 compressive-strength concrete blocks. The tests showed that ripper cutting can excavate large-scale openings of the type required by the mining industry at a production rate that outperforms the conventional drill-blast technique. Moreover, the system can produce openings of various sizes and shapes, is simple to oper-ate and maintain, and produces very little dust or noise during operation. The system appears to meet all of the criteria for a successful hard-rock mining machine.

Jan 1, 1987

By Ionel I. Gardescu

During the summer of 1930 the average daily oil production of Rumania registered a new peak at 128,000 bbl. per day. The estimated potential production as of September, 1930, was as high as 235,000 bbl. per day. During the latter part of the year, by mutual agreement, the operators decided to curtail their output to about 100,000 bbl., which brought the average for the year to 116,600 bbl. The total production for 1930 was 41,572,000 bbl. (last month estimated) as compared with 35,757,000 bbl. for 1929, or an increase of 16.3 per cent. over last year's production. The production for the last 10 years is given in Table 1. The curtailment of production was prorated per company, based on its total estimated potential production as of September, 1930, and not per field. As a consequence, at present there is little development of protected or slightly productive areas; viz., Arbanasi, with an average production of 1750 bbl. per day, dropped to less than one-third after curtailment came into effect. Moreni, with an average production of 92,000 bbl. per day, while producing 58 per cent. of the country's total output in 1929, went to 67 per cent. at the beginning of 1930 and to 75.2 per cent, towards the end of the year. The modified Mining Law of 1929 is still in effect. This law withdraws the restrictions set on foreign capital by the law of 1924. As a consequence a large percentage of proven state land was alloted through competitive bidding to foreign companies. The Romano-Americana (Standard of New Jersey) acquired several leases in the Boldesti and

Jan 1, 1931

By Theodore H. Eyde

The porphyry-copper province of southwestern United States and northern Mexico constitutes the largest copper-producing region in the world. More than 20 deposits discovered since World War II are being exploited or in the process of exploration and development. Because of the remarkable success in discovering new deposits, exploration activity continues at a very high rate and deeper targets are explored each year. Exploration programs for deeply buried porphyry-copper deposits require a reevaluation of the conventional exploration techniques. Though surface induced-polarization techniques have about reached their practical detection limit, aeromagnetics will play an increasing role in the exploration activity as will downhole logging tools. In addition to a valid geological concept, any successful exploration program for porphyry-copper deposits in the southwest must have two other essential ingredients: money and guts. Unfortunately many exploration programs in the southwest are underfunded and doomed to failure. Future exploration will demand more joint venturing in which larger and more expensive exploration programs can be successfully funded by groups of companies or syndicates.

Jan 1, 1975

By W. Todd

The Robbins Company has developed a boring machine, with a rubber packer serving as the gripper system, for blind boring of raises without using drill pipe. This machine is the BorPak and has many applications for use in the mining industry which will improve productivity. In addition to the cost savings, the boring method will lead to increased safety in constructing blind raises. The advantages of using the BorPak in a mining environment will be discussed together with possible applications.

Jan 1, 1994

By L. H. Gevantman

A program for the compilation of evaluated physical and chemical numerical properties data is being pursued at the National Bureau of Standards within the Office of Standard Reference Data. This program is being sponsored by the Department of Energy and managed by the Battelle Office of Nuclear Waste Isolation in Columbus, Ohio. The intent is to assemble a reliable body of numerical properties data concerning candidate mineralogical materials in which high-level radioactive wastes are to be buried. The ready accessibility of the data to site designers and the credibility achieved through the evaluative process are designed to help assess and compare the feasibility of each candidate material for use as a disposal site. Both generic and site-specific data are to be assembled. To date, generic rock salt properties have been assembled and published by the NBS as NBS Monograph 167. Details of the effort to produce this book are discussed.

Jan 1, 1982

By Rosengren KJ

Geotechnical conditions often have a critical influence on the design of new open pit and underground mines, but they are often considered of secondary importance in relation to other factors, such as detailed geology, orebody geometry and grade distribution. As a result, geotechnical studies may not be carried out during early project investigations or, at best, may be given only superficial attention, often to the overall detriment of the project. Technically and economically, it is logical that geotechnical studies should be integrated with geological investigations as soon as it becomes evident that the particular deposit may prove to be economic. The paper discusses the use of geotechnical information in the selection of mining methods and mine design for underground mines and for wall design and assessment of excavation characteristics in open pit mines. It then considers methods of obtaining the relevant data, with particular reference to exploration boreholes. Selected case studies on the application of geotechnical data to mine design are Included.

Jan 1, 1986