Search Documents

By Robert Stefanko

The Federal Coal Mine Health and Safety Act of 1969 had far reaching effects upon many aspects of mining, ventilation being no exception. In this paper, good ventilation procedures are briefly reviewed, and attention is focused on the changes brought about by the new Act. By way of illustration the ventilation system for a typical Pittsburgh Block system is developed and the requirements of the fan determined. This is then solved by an available computer program, and the application is evaluated. Figure 1 represents a projected system for a coal property 1 by 3 miles in plan at a depth of 1000 feet with a coal thickness of 6 feet and desired daily tonnage of approximately 7200 tons on a two-shift basis. Only one half of the mine is shown (north area) with a mirror image mining arrangement to be developed concurrently for the south area. Six working units are projected, three in each area, one on pillar extraction, another developing panel entries and a third on main entry development. A two-split system is used for each working section so that the continuous miner and bolting crews each have a separate split of air, and no equipment need pass through a line brattice. The old requirement of 6000 cfm at the last open crosscut has been increased to 9000 cfm, and for the first time a minimum quantity (3000 cfm) is stipulated at the face thus requiring either line brattice or an auxiliary fan. With the respirable dust requirement limited to 3 mg/m3, the use of a blower system is precluded and exhaust systems are virtually the only choice. Maintaining the line brattice within 10 feet of the working face at all times as required by the new law has a definite effect on the mining cycle and is most difficult at best. In the highly gaseous Pittsburgh seam located in south-western Pennsylvania and northern West Virginia quantities of 20,000 cfm per split are not uncommon to maintain the methane percentage below the required l%

Jan 1, 1972

By W. W. Mein

IN March 1949 the Calaveras Cement Co. was sued by five landowners whose properties are located in the vicinity of the plant. These landowners—all of them cattle ranchers—sued for dust damages of $120,338 and for an injunction preventing the company from casting dust upon their properties in injurious quantities. The issue was split, the jury deciding the amount of damages and the court handling the injunction features. The action came to trial before a jury in April of that year and resulted in damages being awarded in the amount of $7,508. A month later the court issued its injunction requiring recovery of stack dust to an 87 pct minimum. The Calaveras plant, shown in Fig. 1, is located three miles from San Andreas in the heart of the Mother Lode country, about 45 miles east of Stockton, Calif. Since it is in a small town, the company's responsibilities to its employees and to the community are different from those of plants located in large centers of population. Construction of the plant was begun in 1925, and production was started the following year. Standard gray Portland cement as well as several specialty cements are produced. Production facilities have been continually enlarged so that the present capacity is more than double what it was 25 years, ago. The most important item in the company's expansion program was the purchase in 1945 of an 11 ft 3 in. x 360 ft Allis-Chalmers kiln which had been declared surplus by the Defense Plant Corp. The company is now able to produce about 2,500,000 bbl of cement a year, and employment at the plant is approximately 300. The production of cement has always involved a dust problem, solution of which has been attempted in a number of different ways. By far the most efficient method of catching dust discharge is electric precipitation. Soon after the company went into production in the 1920's, the landowners near the plant began complaining about dust discharge. The company settled the matter by paying them a total of $27,000 for dust damages incurred during the period from 1929 to 1938. In the latter year the two-unit Cot-trell Electric Precipitator shown in Fig. 2 was installed and collected over 85 pct of the dust resulting from operation of the two 11 ft 3 in. x 10 ft x 240 in. kilns. From 1938 until 1946 the landowners registered no objection and were apparently satisfied with that dust recovery. In 1946, however, the substantially higher production resulting from operation of the new kiln immediately overtaxed the facilities of the existing two-unit precipitator. In a short time claims for dust damages were again received from the landowners. The company informed them that because of postwar shortages it would take several years to install a new precipitator. The company stated that it intended to purchase an additional precipitator and offered in the meanwhile to pay the landowners a fair amount to cover their damages. This offer was rejected and the landowners filed suit in the Superior Court of Calaveras County asking for total damages of $120,-338 and for the injunction outlined above. Case for the Ranchers The attorneys for the plaintiffs produced three different types of witnesses: first, the landowners themselves and members of their families; second, other cattle raisers who were sympathetic to the plaintiffs; and third, several types of technical experts: veterinarians, soil chemists, and an aerial photographer. The testimony of these witnesses was designed to establish that the flue dust from the plant had not only damaged the land and the forage, but had also caused fluorine poisoning to their animals. By a combination of these causes, the plaintiffs attempted to prove substantial loss of profits.

Jan 1, 1952

By Michael A. Anuta

This report describes the potential for utilization of satellite observations for remote sensing of mine waste disposal areas. Four study sites consisting of metal and nonmetal mining areas in different climatic and physiographic regions of contigous United States were used in this investigation. The mine waste disposal sites consisted of mining of phosphates in Florida, copper in Arizona, silver in Idaho, and coal in West Virginia. Landsat satellite multispectral scanner observations were used together with aerial photographs, ground surveys, U.S. Geological Survey maps, and other ancillary information. Landsat digital data were categorized using automated supervised classification algorithms and an image analysis system. Detailed description of automated classification techniques employed and the accuracy attained is provided together with the results of manual interpretations. The inventory of areas distrubed for phosphate mining and a change detection investigation for-Polk County Florida were also undertaken during this study.

Jan 1, 1982

By R A. Medower

This paper provides a glimpse into the future of minerals processing with emphasis on æAutomation InnovationsÆ for the new millennium, particularly those involving advanced process control and innovative new applications of process control technology in 2007.

Jan 1, 2000

By David Peterson, Terry Tucker, Rafael Serrano

"The Alameda Corridor-East (ACE) Construction Authority awarded a $172.6 million contract to Walsh Construction Company (Walsh) for the construction of a 2.2 mi (3.5 km) long grade separation including a 1.4 mi (2.3 km) long trench that will allow Union Pacific Railroad (UPRR) and Amtrak passenger trains to operate below ground through the city of San Gabriel, Calif. The project is necessary as the ACE trade corridor accommodates approximately 60% of the shipping containers that move from San Pedro Bay, the busiest port facility in the western hemisphere, to the rest of the country via an extensive rail network. Rail traffic is expected to increase by as much as 160% by 2020, and the resultant delays to vehicular traffic is projected to increase by an estimated 300%. The San Gabriel Trench Project is designed to mitigate the effects of this increased train and vehicle traffic throughout the San Gabriel Valley. Malcolm Drilling Company (Malcolm) was selected by Walsh to perform the specialty foundation and ground improvement work for the San Gabriel Trench.This project is part of ACE’s program to create 22 grade separations and safety improvements at 39 grade crossings throughout the San Gabriel Valley. In addition to safety improvements that will eliminate crossing collisions and delays to emergency responders, the project will reduce vehicle congestion and emissions from passenger cars and trucks having to wait for passing trains, and the project will also reduce locomotive horn and crossing bell noise to local residents.Construction of this portion of the project began in late 2012, and it is scheduled to be completed by the end of 2017, having created approximately 9,000 jobs during this period. The project is being funded from Proposition 1B transportation bonds approved by California in 2006, the Metropolitan Transportation Authority (MTA) Measure “R,” and other local and federal funds. The overall project cost is estimated to be $313 million."

Jan 1, 2017

By Mary L. Pearson

Ibis report summarizes the results of the contract. Included are summaries of existing legislation pertaining to outcrop barriers and a state-of-the-art survey of outcrop barrier designs and related, mine closure techniques. Six sites were inspected in the field and are presented as case histories The data analysis presented includes a computer modeled seepage analysis, an overburden blew-out analysis, and a wedge stability analysis. The results tit these analyses are interpreted to form recommendations for coal outcrop barriers which will minimize seepage and the potential for failure. Supplementary support and reinforcement alternatives are also discussed.

Jan 1, 1981

By Marius Jacobs

"Safety performance in many companies and even industries has stalled in the few years. Accidents rates are at a "plateau" and yet, serious accidents and fatality rates are not. In more dramatic cases, such as in the BP Texas disaster, organizations that have "exemplary" safety statistics, suddenly have a catastrophic or multi-fatality event occurring. Other classic examples are the Piper Alpha disaster and NASA’s Challenger and Columbia disasters and even the Chernobyl nuclear reactor. Looking into the root causes of these accidents provides an insight into the events and deficiencies that led up to the accident, but what are the common features in the organization’s mindset? What characterizes these organizations’ decision-making, their approach to safety and to risk and are there specific cultural features that can be delineated? The research and review presented in this paper covers a period since 1994, which started in the Australian resource industry and since then covered international events. The features of these organizations are summarized as the seven deadly delusions, based on extensiveresearch since 1997 of organizations that suffered unexpected disasters.The Piper Alpha Oil Rig disaster in the North Sea, on the 6 July 1988, was one of the most pivotal events in safety around the world. It changed the thinking and focus of governments, whole industries and led to numerous books and papers. It resulted in new legislation, textbooks and a critical self-examination by the oil and gas industry.In short, an explosion and fire occurred when a pipe started leaking gas and ignited. A temporary flange, with no safety valve, was used to block off this pipe during a maintenance operation the previous shift. The permit to advise operators not to start the pumps on this line was misplaced and lost. Several deficiencies, problems and system failures coincided. A key factor was that the water deluge system was inoperable at the time and failed to extinguish the large fire that erupted, followed by an even larger gas explosion. The accommodation unit, situated on top of the oil rig, was the main "killing field" - most men gathered here to await instructions (which never came) and where they died from smoke inhalation. Later, a large explosion of the gas pipeline from an adjoined rig exploded and killed more people.The line of events and the associated system failures are all very relevant in the analysis of the accident, and provide the only insight into what caused the accident. But much "further back", inside the organization’s culture, lurks more dark matter. The first inclination is to ask what was "deficient" in the culture. Did they not care enough about safety, or about their people? Did they have a culture where production decisions were more important than safety considerations? Did they ‘coerce’ supervisors and employees to ignore safety precautions or did they just "fly by the seat of their pants"?Not surprisingly, it is very difficult to identify the true nature of the culture in that business because in such an aftermath of death and destruction, no one dare say that the safety culture was a ‘positive one, focused and caring’ or that the company was doing well in safety and that this is only a freak accident. Indeed, there were many deficiencies in the organization’s systems and procedures, such as the permit to work system.But there are some niggling questions: How is then that the Piper Alpha Oil Rig was actually considered the company’s most productive and safest oil rig in the North Sea? Why would this rig win a safety competition, 6 months before the disaster, with the deficient permit as its most outstanding successful system?"

Jan 1, 2014

By T. J. Lutz, S. Gallagher, J. R. Srednicki, J. J. Sammarco

The Illuminating Engineering Society of North America reports that an underground mine is the most difficult environment to illuminate (Rea, 2000). Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) are conducting ongoing studies designed to explore different lighting technologies for improving mine safety. Underground miners use different visual cues to escape from a smoke-filled environment. Primary and secondary escapeways are marked with reflective ceiling tags of various colors. Miners also look for mine rail tracks. The main objective of this paper is to compare different lighting types and ceiling tag colors to differentiate what works best in a smoke-filled environment. Various cap lamps (LED and incandescent) and lasers (red, blue, green) were compared to see which options resulted in the longest detection distances for red, green and blue reflective markers and a section of mine rail track. All targets advanced toward the human subject inside of a smoke-filled room to simulate the subject walking in a mine environment. Detection distances were recorded and analyzed to find the best cap lamp, laser color and target color in a smoke environment. Results show that cap lamp, laser color and target color do make a difference in detection distances and are perceived differently based on subject age. Cap lamps were superior to lasers in all circumstances of ceiling tag detection, with the exception of the green laser. The incandescent cap lamp worked best in the simulated smoke compared to the LED cap lamps. The green laser was the best color for detecting the tags and track compared to the red and blue lasers. The green tags were the easiest color to detect on the ceiling. On average, the track was easier for the subjects to detect than the ceiling tags.

Jan 1, 2013

By F. D. Everett

The Federal Bureau of Mines reviewed the status of tungsten deposits of Utah in 1959. Industrial requirements of tungsten during emergencies have exceeded the domestic supply, and a knowledge of the sources of this strategic element may be helpful in the future. Tungsten occurs as the mineral scheelite in deposits that have been developed or explored on approximately 60 properties in 10 of the Great Basin ranges of Utah, none of which were being worked in 1957-59. Ores from most of the productive areas are similar in that they are contained in tactite deposits on or near the contact of calcareous and acidic intrusive rocks. The tactite ores consist predominantly of the silicate minerals garnet, epidote, and diopside and the carbonate rocks limestone or dolomite. Scheelite, where present, is disseminated irregularly in the tactite. Tungsten ores from Utah mainly have been produced from small deposits worked in World Wars I and II and the Korean campaign. The ores were either hand sorted to a grade ranging from 0.5 to 1.0 percent tungsten trioxide (W03) or were beneficiated in small mills to higher grade concentrates. The largest reserve appears to be in the area of the Notch Peak intrusive in the House Range, Millard County. A large part of the reserve in the House Range is mineralized tactite containing 0.2 to 0.3 percent W03. Research on flotation by the Bureau of Mines has indicated a method of concentrating scheelite in tactite ores that average 0.25 percent W03, with at least 85 percent recovery. The concentrate assays more than 5 percent W03 and can be processed into artificial scheelite ready for industrial use.

Jan 1, 1961

By G. M. Hutt

Introduction The major development of industrial minerals in Manitoba has been in building materials. 'The building-stone industry is developed far beyond the needs of the Province, and the well known Tyndall limestone is marketed over a wide area throughout the other provinces to Canada. Similarly, gypsum and gypsum products are produced in excess of local requirements and are exported to adjacent provinces. The crushed-stone, sand and gravel, limestone, and lime industries are sufficiently developed to supply the needs of the Province and, notably in the case of lime and lime-stone, there is a surplus for export to the adjacent provinces and to the United States. The manufacture of common brick is well established, but for face-brick and other clay products the Province is dependent largely on importations. Production of silica-sand will increase as Canadian markets become available through recognition of the utility value of the Black Island sand as foundry-sand and for other purposes. There is some possibility of the export of feldspar, of lithium ore and concentrates, and perhaps of salt. A considerable part of the Province has not been seriously prospected for industrial minerals and it may be expected that, as time goes on, other deposits of non-metallic minerals will be discovered and opened up, especially as the prairie provinces become more industrialized. At the present time, there is some activity in the southern part of the Province based on gas and oil indications. Whatever may be the outcome of this work, it should yield valuable information concerning the geological structure of the area.

Jan 1, 1934

By Arno C. Fieldner, J. W. Paul, WALTER A. SELVIG

Many mine samples of coal are analyzed each year in the laboratories of the Bureau of Mines. The analyses are made in connection with investigations relating to fuels belonging to or for the use of the United States Government, the causes of accidents in coal mines, the geologic relations of coal beds, and the quality and the value of the coal and lignite in the public lands. The systematic collection and analysis of such samples in connection with fuel investigations was begun in 1904 at the Government fuel-testing plant at the Louisiana Purchase Exposition. and was under the direction of the United States Geological Survey for six years. Descriptions of the coal samples collected between the beginning of this work, July 1, 1904, and the transfer of the fuel-testing and mine-accident investigations to the Bureau of Mines,July 1, 1910, were compiled and published in Bureau of Mines Bulletin 22.' Descriptions and analyses of samples collected during the fiscal years 1911 to 1913 were published in Bureau of Mines Bulletin 85.2 Descriptions and analyses of samples collected during the fiscal years 1913 to 1916 were published in Bureau of Mines Bulletin 123.3 The present bulletin presents analyses and descriptions of samples collected during the fiscal years 1916 to 1919. In order that the material in this bulletin may be used to supplement that presented in Bulletins 22, 85, and ,123, the same plan of geographical classi- fication has been followed, the analyses and descriptions of the samples being grouped in alphabetical order according to the State, county, and town near which the mines or prospects sampled are situated.

Jan 1, 1922

By A. Delgado-Jiménez, O. J. Restrepo-Baena, G. Aristazabal

"Mining industry as a source of raw material is essential to society however, it lacks of good reputation due to the type of management historically applied to many of its social and environmental impacts. It is argued that this situation has hampered the obtaining of social license to operate of a lot of mining projects around the world. The last considerations are very common in Latin American countries. As a result, the mining sector has understood that the viability of the business long term is associated with more profit for the shareholders but also with activities that improve the livelihoods of local communities, enhance the capabilities of local governments and preserve the ecosystems around the projects. Nevertheless, recent studios have shown that most of the current advances to incorporate sustainability concepts in mining have been mainly focused on control and the prevention of environmental and social impacts of extractive activities. Thus, contributing to the development of territories around mining projects constitutes a fundamental aspect of the business competitiveness through reducing cost and risks of stopping projects, innovating new ways of relationship with stakeholders, improving the level of reputation of the industry as well as its position in the market. However, this contribution requires formal strategies and models that enable companies understand the different resources in the territories where their mining activities are developed and those resource transformations, in order to establish the best way to articulate the project with the territory, pursuing an effective contribution to its development, truly sustainable over time even after the mine closure. CONTEXT Currently in the world but especially in developing countries such as Latin Americans, different stakeholders are increasingly vigilant of how mining companies carry out their activities in terms of socio-economic and environmental management of territories, not only for its impact on the livelihoods of the communities that inhabit them, but also because many demanders of raw materials -both countries and companies- have set sustainability standards as a prerequisite to establishing business relationships with mining companies, such as the recently declared Sustainable Development Goals by 2030 (UN, 2015). Accordingly, decide underinvest or not to invest in sustainability issues carries risks for mining companies. However, invest much in the wrong way may involve the same risks. Managers are concerned to ensure profits, and therefore they decide carefully how to invest in the areas of production, R & D or marketing. Likewise, they should think strategically about investing in initiatives related to sustainability. This if they really want that those investments in fact help to improve the competitiveness of the company. The mining industry benefits from natural capital that extracts, so it should implement strategies that lead to remunerate such benefit to the territories (Almaguer, 2007). One option is through the transformation of natural capital in other types of non-existent capital or poorly developed in their areas of influence. In this way, the value generated by the extraction of underground resources is shared and additionally contributing to improving the quality of life of the communities. Historically, mining industry has been into several problems to achieve this, which represents one of the aspects that has most influenced the current reputation of mining industry in some regions of Latin America. Many communities, local governments and civil society organizations continue to associate this activity with the destruction of the social fabric and ecosystems in the territories, and their opposition against companies working in the areas has led to affect the operational continuity of many projects (Hamann, 2003; Prno and Scott, 2012; Slack, 2012)."

Jan 1, 2017

By Christine E. Turner-Peterson

Pore-filling organic material concentrated uranium to form sandstone-hosted primary uranium deposits in the Jurassic Morrison Formation of the Grants uranium region, New Mexico. Petrographic observations and radiometric ages for primary ore in the Westwater Canyon Member require that the organic material was emplaced early in the diagenetic history of the host sandstone; in fact, organic material was emplaced before major compaction. This inferred early emplacement constrains models concerning the nature and origin of the organic material and thus also constrains models of ore genesis. Reconstruction of the burial history of the basin indicates that Late Jurassic-Early Cretaceous time, the interval of inferred emplacement of the organic material, was probably not a time of hydrocarbon generation and migration. Nuclear magnetic resonance analyses, elemental abundances, and isotopic studies provide further constraints on the nature of the organic material, and data from these studies are consistent with a humic acid rather than an oil origin. In addition, the overall tabular shape of primary uranium orebodies and the way these orebodies are suspended in the host sandstone mimics Recent deposits of humate, the precipitated form of humic acids. The critical clue that favors a humic acid origin for ore-related organic material is provided by the nature and patterns of postdepositional alterations that are spatially and temporally related to primary ore, specifically destruction of detrital magnetite and ilmenite (iron-titanium oxide) grains. Humic acids are implicated in the destruction of iron-titanium oxide grains because these organic acids are one of the most effective natural agents in leaching of Iron from these grains. Thus, timing constraints, chemical evidence, orebody geometry, and the nature and patterns of ore-related alterations favor a humic acid origin and suggest that an oil origin is highly unlikely. Because alteration of iron-titanium oxide grains tracks the pathways of humic-bearing solutions through the host sandstones, it is possible to trace these solutions back to their source. Alteration patterns in the Westwater Canyon Member suggest that the humic-bearing solutions originated as pore fluids in the mudflat facies of the overlying Brushy Basin Member and moved into adjacent sandstones during early dewatering of the mudstones. The humic acids precipitated, by the process of cation loading, in tabular layers. Uranium was concentrated within these tabular layers by complexation with the humic acids to form primary uranium orebodies.

Jan 1, 2013

By L. V. Bell

THE object in prospecting is to find ore. With the exception of certain discoveries of more or less accidental nature, intelligent prospecting as conducted today is, whether consciously or not, based upon a process of elimination. In the following discuss on it is proposed to evaluate those factors that enter into the eliminating of certain tracts of ground and, conyersely, the concentrating of attention upon others. The danger of generalizations as to the barrenness of cer.ain areas, without having due regard for all such factors, is emphasized. The fact that our conception as to what areas or rock formations are to be regarded as favourable or unfavourable is, in some measure at least, changing with new discoveries under diverse and unexpected circumstances, adds more point to the discussion. The criticism might be raised that the subject is treated largely from the standpoint of geology, but that may be met by stating that it is, and must continue to remain, precisely from this standpoint that the prospecror directs his activities. Briefly, the geologist may render the greatest service to the prospector in the early steps of selecting (a) the general territory in which to prospect; (b) the area to be intensively prospected; and, finally, (c) those parts of the claim or claims to be prospected in detail. Although certain phases of the discussion will be, in some measure, of general application, we shall here concern ourselves essentially with prospecting in the pre-Cambrian shield. Furthermore, the subject is so large that it has been decided to limit it to a consideration of that portion of the pre-Cambrian rocks in which is situated the mining district of western Quebec, of which the writer can speak with more personal knowledge. This limitation need not, however, seriously detract from whatever merit the discussion may possess, since the deposits concerned cover a fairly wide range of metallic ores, including gold, copper with associated zinc, and, lastly, molybdenum.

Jan 1, 1936

By R. R. Klimpel

This paper demonstrates, using the results of an unusually complete industrial test sequence, what the various interactions are between grind size, collector dosage, and frother type. While particle size is universally acknowledged to be important in optimizing industrial copper sulfide rougher flotation circuits, many of the various interactions that do occur at the industrial level with particle size are still being identified and/or quantified. This study also presents, in a consistent manner, the changes in flotation kinetics that occur as a function of particle size, in a typical industrial circuit along with some insights as to how flotation operators can optimize rougher circuit performance.

Jan 1, 1993

By William H. Shockley

[SECRETARY'S ]NOTE.-The following notes, arranged and edited in this office, but not yet revised by the author, were placed at my disposal with much modest hesitation (due to their incomplete and fragmentary character), upon my earnest request, and my argument that such recent and trustworthy data concerning a new and important mining industry ought not to be withheld from our Transactions, simply because they are not sufficient to constitute a, complete academic treatise on the subject. This argument is recommended to the attention of many other members, who are waiting for the opportunity to contribute something "monumental" to our Transactions. In a number of instances, death has nulli¬fied this ambition, and the intended "monumental" contribution has turned out to be an obituary notice by the Secretary, instead of a valuable record of the professional experience thus hopelessly lost to the world.-R. W. R.] The official publications of the the Russian Government give fairly complete statistics of the dredges operated in the Empire; and in a recent English bluebook, Mr. Cook's report on Siberian Trade presents a brief account of dredging in Siberia. The data in Table I. (not given by Mr. Cook) have been taken from the Gold Mining Messenger (Russian) for July, 1905. These interesting statistics, though incomplete, show that the Yenisei dredges are working on poor ground and yield small returns. According to report, but few yield a profit exceeding 10 per cent. per annum on the capital invested. In the summers of 1904 and 1905, I traveled in the Urals as far north as lat. 61° N., long. 61° E., on the the Lozva river, a part of the vast system of the 01) river. This clear-water stream starts from the summits of the Urals at an altitude of 4,000 ft., and flows through a flat country, densely wooded with larch, spruce, pine, fir, birch and poplar. The river is full of fish, and is navigable for good-sized steamers as far as Ivdell. Winter lasts from early November to late April, the temperature rang¬ing from -60° F. to a summer maximum of 90° F. The rain¬fall is 20 in.. The climate is healthy, although mosquitoes,

Jul 1, 1906

By William J., Coulter

IN the early days of Colorado mining, between 1880 and 1900, when Leadville, Kokomo, and Robinson were boom mining camps, the entire area around Climax for a matter of fifteen miles was overrun with prospectors, so the mineralized outcrop at Climax was not unknown. The principal interest in minerals during this period was in gold, silver, and lead, and since the Climax outcrop showed none of these it drew little attention. Geology played an important part in bringing prospectors to the very edge of the Climax deposit. The Mosquito fault, which crosses near the base of Bartlett Mountain, continues as an important geological structure, at least as far as Leadville some twelve miles distant, and at the base of Bartlett Mountain the vertical throw on the fault is estimated to be between 2000 and 5000 ft. The sedimentary beds known to the Leadville district are all present on Bartlett Mountain to the north of the Mosquito fault, which cuts them off abruptly, and exposes the Pre-Cambrian rocks that underlaid them, so the prospectors, who were searching for gold, silver, and lead in the sediments

Jan 1, 1946

By Leslie McHattie

?Intelligent mine? conjures up a futuristic image of unmanned extractors and loaders working in harsh conditions in a remote lunar landscape. The promise of increasing mine fleet productivity and solving the problem labor shortages in mining regions can certainly be achieved today through remote controlled extraction and automated hauling. The technology is available and it doesn?t seem to be so much science fiction when Google?s self-driving cars hurtle down the freeway. ?Intelligent mining,? on the other hand, implies the application of information technology at every phase of the mining value chain, from exploration and geological modeling to equipment, operations and maintenance, and logistics and transportation. These are really industry-specific, enterprise-class software solutions focused on using information technology to support the business processes of mining and make them more efficient and effective. Overlaying the physical world with the digital or virtual world enables us to model and simulate our assets, giving us the ability to effectively design, build, and ultimately optimize the performance and reliability of our assets throughout the lifecycle. The digital asset, often a 3D model, is created initially during the engineering and construction phase, and is handed over to the operator before the mine goes into operation. Combined with geospatial or geographic information systems, the operator has a complete digital representation of the physical world, which forms the foundation for risk and performance management, along with compliance and regulatory reporting. Laser scanning and positioning technology can be used to create point clouds ? information models consisting of millions of data points ? which enable the visualization and representation of the ?as-operated? reality. But consider that once the mine is in operation, it throws off an endless stream of data in the form of performance and condition data from sensors and monitoring devices on fixed and mobile assets through networks, servers, and services. This ?big data? can be processed and analyzed to spot trends, help predict events, and formulate reliability strategies as early as the design stage (e.g., reliability-centered design). ?Intelligent mining? implies that massive amounts of data augment the reality of the physical mine, plant, and equipment. This embedded intelligence can be used to optimize operational efficiency, increase asset availability and utilization, improve safety and environmental integrity, and maximize return on investment. Lastly, the sweet spot for intelligent mining is seen in the convergence of consumerization and industrialization. The application of ?consumer? technologies that we use every day on our iPhones and Android devices, such as cameras, motion sensors, and positioning in an industrial context, are producing ?immersive? experiences. Overlaying the digital world on the physical world and connecting them accurately through intelligent positioning results in ?intelligent infrastructure,? which is safer and more sustainable. Bentley Systems works with many mining companies and engineering, procurement and construction companies involved in all aspects of mining infrastructure development. In fact, 10 of the top 20 mining companies ranked by market capitalization are users of Bentley software, including all of the top five. In addition, Bentley provides software solutions to the world?s leading engineering, procurement, and construction companies, as well as owner-operators, who design, build and operate the world?s infrastructure. Bentley?s solutions for mining and resource extraction industries help increase the efficiency of capital projects associated with the design, procurement, and construction of mines and processing plants, as well as the operation and maintenance of mining fleet and equipment.

Aug 1, 2013

By John G. Parker

Many of the so-called minor metals are derived as byproducts from the processing of lead and zinc concentrates in which they occur as minor constituents. Concentrates from some lead-zinc mineral deposits are more enriched in metals such as cadmium, arsenic, bismuth, silver, and selenium than are others, and these sources offer a continuing, assured supply of certain of these metals. Despite the age of the data collected, the Bureau of Mines feels it to be highly desirable to publish due to its relevance to the objective of the study which was to ascertain the flow of minor metals from certain smelter feeds Efforts to trace these metals through the complicated lead and zinc processing steps included trying to ascertain losses and mode of loss of these metals. Losses of some metals in processing may be surmised as occurring in gaseous and other emissions, or possibly in slags and residues.

Jan 1, 1979

By W. R. Lindsay

Anyox, where the Hidden Creek mine of the Granby Consolidated Mining, Smelting and Power Company is located, is situated on an excellent deep-water harbour in Granby bay, at the head of Observatory inlet, about 600 miles from Vancouver and 90 miles north of Prince Rupert. Anyox is the Indian name for the little stream which empties into Granby bay, and means 'hidden creek'. The Ore-Bodies The ore is a replacement deposit and occurs at and near the contact between argillites and a later intrusive greenstone. This contact locally has a general north-and-south trend, an irregular westerly dip, and in the vicinity of the ore-bodies there has been intense folding, accompanied by faulting. The mineralizing solutions supposedly were derived from the Coast Range granite batholith, distant one to two miles to the east and north. The whole area is cut by many dykes of varying widths, which seem to have had but little part in the ore deposition.

Jan 1, 1929