Search Documents

By ANGELA NAIR AVELAR, Reiner Neumann, PAULO R. G. BRANDÃO

The understanding of the influence of the different types of apatite on the performance of mineral processing of igneous phosphate ores is still a challenge due to the difficulty to explain why some types of apatite floats in the froth flotation cell and others do not under the same conditions. Three types of apatite were identified by means of cathodoluminescence (CL) images in flotation concentrate and tailing samples from the Catalão mine: predominantly blue apatite, followed by green apatite and less frequently yellow apatite. The chemical composition of these types of apatite was determined by electron microprobe analysis (EPMA) and LA-ICP-MS. Blue and green apatite respond well to the process, thus remaining in the concentrate, while yellow apatite remained in the tailings. Yellow apatite is the one bearing the lowest P2O5 content and the largest anionic and cationic sites substitution, followed by green apatite, whereas blue apatite is the most homogeneous, with highest P and Ca grades and lowest substitution level. A negative correlation of the amount of phosphorus with fluorine was observed. Furthermore, impregnation of iron oxide-hydroxides in the yellow apatite was also observed. Therefore, the low flotation behaviour is due to low crystallinity coupled with impregnation onto its surface.

Jan 31, 2022

By Kimberlie Staheli

A new sanitary sewer was installed in Pleasant Hill, California using microtunnelling methods. The project consisted of 693 meters of 1372 mm and 1981 mm concrete pipe. A Herrenknecht AVN 1200 was used to install the nominal 1372 mm pipe in three drives. The machine was then fitted with an oversized shield used to install the large diameter pipeline. This articulated shield allowed the excavation of a 2362 mm diameter hole with a 1524 mm machine-- a technique new to North America. This paper reviews the design considerations for the articulated shield and reports on the project challenges and solutions to overcome these challenges.

Jan 1, 1995

By Matheus Machado de Souza

A utilização de revestimentos a base de cromo eletrolítico traz prejuízos ao meio ambiente, uma vez que durante o processo são liberados íons de cromo hexavalente e estes são extremamente tóxicos à natureza e ao homem. No entanto, existem outras tecnologias que vem sendo estudadas como alternativas ao processo tradicional de cromagem. A aspersão térmica por oxi-combustível de alta velocidade (HVOF) é a técnica que tem apresentado os melhores resultados sob as óticas de qualidade de revestimento, porosidade, resistência ao desgaste, propriedades mecânicas e adesivas. Neste trabalho foi realizado um estudo comparativo da eficácia da técnica de HVOF em termos de adesão, resistência ao desgaste e coeficiente de atrito. Como substrato foi utilizado o aço SAE 4140; o revestimento utilizado na aspersão por HVOF foi o WC-Co-Cr em comparação como o cromo eletroliticamente depositado, todos com a mesma espessura de camada. A avaliação tribológica foi realizada através de ensaios de desgaste por deslizamento do tipo pino sobre disco e a resistência adesiva por meio de ensaio de adesão.

Aug 7, 2018

By Kenneth N. Weaver

Portland cement can be made from relatively abundant industrial minerals and rocks, and this may explain why cement producers placed little emphasis on geology during the early days of the industry. After World War II, however, the industry began to recognize the need for geological exploration, and some of the larger companies began to build a permanent geological staff. This development had its roots in the following factors: Rapid expansion of the industry; closing of many cement plants due to inadequate raw materials; necessity for upgrading the quality of portland cement; and the increasingly large capital investment required to build new cement plants, which in turn, required a higher degree of accuracy in reserve calculations. Whereas the geologist's function during the active expansion of capacity was primarily in exploration, one of his major functions today is the development of existing reserves.

Jan 1, 1965

By H. C. Meister

THE zinc-smelting industry of the United States has grown very rapidly in recent years and bids fair to outrival that of all other countries in the future. On account of the geographical situation of the chief ore-supplies, the industry may be divided into two main groups, the eastern and the western. The eastern and older group includes the works of Pennsylvania, New Jersey and Virginia, which practically control their own ore-supply. The western group includes the works of Illinois, Missouri, Kansas, Wisconsin and Indiana, which do not control their own ore-supply, but are compelled to buy the ore in the open market. It is for this reason that the western zinc-smelting industry has been undergoing continual changes since its inception 40 years ago. During the early discoveries of lead- and zinc-ore in the lead- and zinc-districts of Wisconsin and northern Illinois, the zinc-ore (sinithsonite or " bone " as the miner calls it) had no value and was considered waste; but later, when this ore was found in large quantities, it attracted the attention of metallurgists, which finally resulted, during the early sixties, in the building of the Matthiessen & Hegeler Zinc Works at LaSalle, Ill., the pioneer zinc-works of the West. A few years later, zinc-ore was discovered associated with the lead-ore in Jefferson county, southeastern Missouri, which started the industry at Carondelet or South St. Louis. Still later, the discoveries of zinc-ore in the lead-ore region, first' at Granby and then around Joplin, lead to the introduction of the industry in the southwest Missouri and Kansas districts. At first the development of the industry was slow, but it progressed steadily and it is now one of the leading metallurgical industries of the middle West.

Jan 1, 1905

By Edwin T. Wood

THE term blending as used herein refers to the mixing of ores assaying more than 0.20 pct U3O8 with low grade material assaying less than 0.20 pct U3O8. Such blending when properly understood and controlled will produce more total dollars of profit from many mining ventures. The question whether or not to blend is particularly vexing when an orebody is surrounded by an envelope of low grade material or separate tonnages of low grade exist which could be extracted coincident with the higher grade ores. Should any, all or part of this low grade be mined? If so, in what proportion and what is the limiting assay of the low grade material?

Jan 7, 1958

By E Garbarino, P Molina, V Badino

Given the ever increasing quantity of construction and demolition waste (C&DW), one of the most challenging issues presently facing policymakers and public administrators in Italy concerns how to organise and manage collection and recycling and to understand whether and to what extent recycled aggregate can complement natural building aggregates in a sustainable supply mix (SSM). The paper presents the results of a research aimed at analysing energy and environmental implications of the C&DW recycling chain in the administrative territory of Provincia di Torino in northern Italy. In respect of a population of about 2.25 million inhabitants, the annual production of C&DW in the area under study is 1.8 Mt. A combined geographical information system (GIS) and Life Cycle Assessment (LCA) model was developed, paying attention to the geographical location, land use, transportation network and avoided landfill: crucial issues for sustainable planning and management. Around 90 recycling plants were classified according to the size, typology (stationary, semi-mobile and mobile) and physical- mechanical characteristics of the recycled aggregate. Under different assumptions relevant to the delivery distance, and considering the typology and grade of recycled aggregate, as well as local availability of natural aggregates, it was possible to evaluate the geographical coverage of aggregates demand and to use LCA in order to identify and quantify energy and environmental indicators.

Jan 1, 2009

By C. H. Loux

This paper deals primarily with the advantages realized from the adoption of methods more suitable than those previously used. The improvements noted include: (1) modification of practice in shrinkage stoping, (2) use of sublevel caving over grizzlies, (3) improved haulage and loading, (4) use of contract wages wherever possible. The Washington mine is on Jonestown Hill, one mile south of Oxford, in northwestern New Jersey. It is producing 16,000 tons of concentrates a month, which are being shipped to the Alan Wood Steel Company's furnaces at Swedeland, Pennsylvania. History The first settlement in this region is reported to have been in 1735, and the magnetite ores were recognized immediately. The first furnace, built in 1741, began operation in 1743. During the Revolutionary War the output was chiefly used for making cannon balls, which, owing to the sympathies of the community, without doubt found their way into the hands of the British. This old furnace is still standing. Several important veins were soon developed, including the Martin, Strayley, McKinley, Adelaide, Welsh and Lanning. Mining was carried to a depth corresponding to the capacity of the pumps available. When these became inadequate, the workings were abandoned, and another vein was opened up. The Washington vein was probably discovered about 1850, and the first shaft started in 1854. In 1879, William H. Scranton made the first complete magnetic survey of the district and serious exploration of the deposit was begun. Rather indifferent success attended the earlier efforts of the many companies that attempted to mine and smelt the ore. In 1929 the property was leased by the Warren Foundry and Pipe Co. to the present operators, and the modification of practice then inaugurated is described in this paper. Geology These veins, like most eastern deposits of magnetite, are formed from, or are contemporaneous with, pegmatite intrusions into a gneissic country rock. The ore therefore follows the banded structure of the gneiss,

Jan 1, 1934

The authors of T.P. 4179 have conducted a large number of experimental water floods, and the data are reported in a very clear manner. These data show significant variations of residual oil saturation with changes in wettability, interfacial tension, flooding rate, and oil-water viscosity ratio. Furthermore, some of the data obtained cover a range of variables not previously reported in the literature. It is our opinion that at least some of the observed variation in oil recovery can be obtained only in floods made under conditions identical with those used by the authors. There are other systems which may be said to have the same wettability, but which exhibit an entirely different qualitative dependence of oil recovery on the experimental variables. In this regard, we would like to direct attention to several items which we feel are not given sufficient consideration in the paper. The first of these items has to do with wetting equilibrium. A survey of the current literature will reveal that little is known, and even less is understood, about wetting equilibrium. This is particularly true of the relation between contact angle measurements made under static conditions, and the wettability existing under the dynamic conditions of floods carried out at relatively high rates. We feel that this is a very important consideration, particularly in the floods the authors performed under what they consider to be "water-wet" conditions. It is our opinion that wetting equilibrium did not exist in these floods, except possibly at the very lowest rates. This opinion is in part based on some flooding tests we have made which are very similar to some of those described by the authors. These floods were made in unconsolidated cores, 6 in. long and 13/4 in. in diameter, made up of carefully graded glass spheres of the approximate size of the sand grains used in the subject paper. The cores were mounted vertically, and distilled water was used to displace a refined oil equivalent to the authors Soltrol C. The glass spheres had previously been carefully cleaned so that they were strongly wet by the water. The floods were made with and without an interstitial water saturation. When interstitial water was present, the solid surfaces were mostly covered with water prior to injecting the flooding phase. Consequently, a condition very near wetting equilibrium existed throughout the flood. The data in Fig. A show that under these eircumstances, rate had no influence on residual oil at flood-out, over the range of rates studied. On the other hand, in the absence of interstitial water, the surfaces are all covered with oil before the displacement. To achieve wetting equilibrium the injected water must displace the oil from the surfaces themselves. This is not a fast process. Therefore, the effective dynamic wetting condition in floods of this type must depend upon the flooding rate. When the flood rate is very low, compared to the rate at which wetting equilibrium is attained, the residual oil saturation at flood-out is essentially the same as the residual obtained when interstitial water is present. This is shown in Fig. A, and occurs because the dynamic wetting conditions are the same in both cases. However, at moderately high flooding rates, the rate has an important bearing on the amount of oil recovered because in this case the attainment of surface equilibrium is the slow step. We believe that, in the absence of an interstitial water saturation, oil recovery varies with rate because of the reasonably slow approach to wetting equilibrium which occurs during the displacement. In fact, as the rate is increased, the oil recovery performance indicates the core is becoming progressively less water-wet. At the highest rate there is even considerable simultaneous production of oil and water after breakthrough. This does not occur at the lower flooding rates, nor is there appreciable simultaneous oil and water produc-

Jan 1, 1957

By Johann Knecht

Due to lower specific investment and operating costs the tendency towards large scale equipment will remain. For the design engineers not only the stresses in the mill structure and manufacturing are of importance but also transportation to and erection on site. A scale up of the design of smaller sized units on the pantograph principle may not always give the best approach to the job in this respect. This paper covers recent developments in the design of large size equipment where the huge dimensions call for designs being different to the well known ball and SAG mill concept with cast conical endwalls. The first part describes the features of the biggest ball mill in the world, whereas the second part provides some details of the largest shell supported SAG mills being currently in the manufacturing process.

Jan 1, 1993

By T. Mudder, R. Cellan, R. Waterland, J. Whitlock, B. N. Nelson

The effectiveness of anaerobic in-situ biological treatment for the immobilization of selenium, molybdenum, and uranium in an alluvial aquifer was examined using long-term column tests. A series of organic substrate and nutrient combinations were tested to determine removal effectiveness, optimum supplement concentrations and ratios. Final column testing was conducted to determine the chemical stability of the treatment by-products/treatment compounds by dosing the columns continuously with elevated redox untreated alluvial groundwater.

Jan 1, 2002

By G. W. Poling

Sedimentation behaviour of siliceous mill tailings derived from a magnetite-chalcopyrite ore in fresh water, fresh water - sea water mixtures and full-salinity sea waters are compared. Results of batch settling tests are presented in the form of settling curves and solids flux curves. The addition of a few per cent of sea water markedly enhanced the zone sedimentation rate due to particle agglomeration caused by a reduction in zeta potential of the suspended solids. The presence of a small amount of residual, previously magnetized magnetite in the tailings also enhanced agglomeration and sedimentation. The significance of these results to submarine disposal of mill tailings is discussed.

Jan 1, 1973

By Steven D. Sandbrook

A man by the name of Louis Binstock once said, “Too often the shortcut, the line of least resistance, is responsible for evanescent and unsatisfactory success.”

Jan 1, 2015

By Oliver Bowles

Cementing materials of mineral origin were well known to the ancients. Ordinary lime and gypsum plasters were the first to be recorded by historians. The next development was the discovery that certain limes would set under water, but the hydraulic property was not definitely attributed to the presence of clay in the limestone until many centuries later. The Romans advanced a step nearer to modern cement in the development of 'pozzuolana', a mixture of volcanic ash or trass with hydrated lime. The silicate of aluminium in the volcanic rock combined readily with the lime, forming a hydraulic mortar or cement which was widely used. Natural Cement In Europe (1) No further progress was made in the art of manufacturing cement for several centuries, during which the Roman Empire declined and passed away, and the Anglo-Saxon race slowly and painfully evolved through the Middle Ages an ever-increasing prestige. An Englishman, John Smeaton, is credited with the honour of the next important development, for he employed a little-known cementing material-natural cement-in constructing the Eddystone lighthouse in 1756. It was called 'natural' cement because it was made from a natural rock with no additions of other materials. The process consisted of calcining an argillaceous limestone at a comparatively low temperature and grinding the product to a fine powder. Care was exercised to keep the temperature low, and any material burned to the clinkering point was thrown away, although such material was, as learned at a later time, Portland cement.

Jan 1, 1933

By Jean A. Andre

In 1969 "Société des Mines et Fonderies de Zinc de la Vieille-Montagne" produced 221,000 tons zinc ingots and 22,000 tons zinc dust, thus rating highest on the world's zinc producer list. The Company's plant at Balen, Belgium, with an output of 135,000 tons electrolytic zinc is the most important one of this group; it is an integrated metallurgical zinc and lead unit with recovery of most by-products. The present paper describes the zinc production facilities. The roasting section includes four fluid bed roasters (total concentrates charged: 740 tpd) and two sulfuric acid having a corresponding capacity. Calcine is leached in a fully automated plant by a two-step continuous process. Leaching residues, mixed with lead furnace slag, are treated in a shaft furnace. The recovered zinc fume is leached separately. In the near future, the leaching residues are to be treated by a wet process, developed in the Company's own laboratories. Purification of solutions is accomplished in two steps: antimony and zinc dust are added in the first one, only zinc dust in the second one for removal of cadmium. Electrolysis cells are partly of a conventional type. A new type of cell configuration was put onstream in October, 1969, planned output 60,000 tpy. Main features of the new cell rooms are the fully automatic pulling, stripping and replacing of the jumbo-size cathodes (immersed area 2.6 m2). Zinc cathodes are remelted in induction furnaces followed by in-line automatic casting and stacking machines.

Jan 1, 1970

By RAYMOND C. HARTVIKSEN

The Drumbo Mine is located near Highway 401 between Woodstock and Kitchener in southwest Ontario. The tabular flat-lying gypsum bed is between 1.5 to 2.4 m thick and is situated near the base of the Salina Formation, about 116 m below surface. The mine is owned and operated by Westroc Industries Limited. The 3.8 m diameter shaft was drilled using a Hughes CSD 820 drilling rig and a liner sinking technique new to the North American continent. The shaft was completed in the fall of 1977, and remaining facilities were finished in the fall of 1978. Gypsum production started in December 1978, employing the conventional room-and-pillar method of mining.

Jan 1, 1984

By WenFeng Li

Comparing to the coal seams in Eastern China, the coal seams in Western China usually have better geological conditions. Therefore, changes in the conventional gateroads layout are required for the Western longwalls. A case study based on a Western coal mine (LiMin) was presented to discuss the feasibility of an innovative gateroads layout. Based on the geological conditions, a 5m wide pillar between the adjacent two longwall panels, 09112 and 09113, was proposed in order to increase the recovery rate. More importantly, the entry supporting strategy of panel 09113 headgate needed to be determined and verified carefully since only 5m wide pillar was left to separate the entry from the panel 09112 gob. Three strategies with different supporting intensities in the panel 09113 headgate were evaluated by numerical modeling. The model outputs indicated that roof and rib boltings plus single hydraulic props were essential to maintain the gateroads stable. Field observation showed that under the proposed entry supporting strategy, the total roof-tofloor and rib-to-rib convergences were only 360mm and 460mm, respectively, during the service life of the panel 09113 headgate, which indicated that the innovative gateroad layout proposed in this paper is suitable for longwalls with similar geological conditions in Western China.

Jan 1, 2013

By Houtgraaf M

The Far Fanning gold deposit is situated 60 kilometres south-west of Townsville (Fig. 1). Previous recorded production is 3756 tonnes returning about 1600 ounces of gold. This has been taken from surface and shallow underground workings- scattered over the strike length of the deposit of 1700 metres. The main production period was from 1895 to 1908.Previous exploration involving extensive trenching and sampling has been: carried out intermittently. since the 1930's, by Gold Mines of Australia (1932), Placer (1974), Anaconda (1975), Marathon (1980-8-1), Aberfoyle (1981-82), and The Northern Queensland Company (NQC) (1983-present).In 1980 Marathon undertook an extensive drilling programme to test the oxidised mineralisation. Over 200 percussion holes and- 7 diamond holes were drilled along traverse lines spaced 29 to 103 metres apart covering a strike length of around 1800 metres.

Jan 1, 1986

By AIME AIME

I N JUNE, 1918, at a meeting of the American Society of Mechanical Engineers in Worcester, Mass;, a resolution was adopted for a committee to investigate the aims and organization of that society. This was followed subsequently by similar independent action on the part of the Society of Civil Engineers. The other two Founder Societies were approached and requested to appoint similar committees, the four committees to combine as a .Joint Development Committee, later called the Joint Conference Committee, to investigate what might be done in the way of coordinating those activities of the Founder Societies which ape of common interest, and which were then being pursued separately. The Joint Conference committee worked diligently -for almost. two years and. brought forth a tentative as outlined in its report which was published in full in MINING AND. METALLURGY, December, 1919. It recommended the formation of a nation-wide organization to be composed of representatives' of all of -the engineering societies, local, state, regional, or national, the object to be to further the interest of the public through the use of technical knowledge and engineering experience, and to consider and act upon matters common to the engineering and allied technical professions. Whereas the technical societies have large fields of endeavor in welfare work, and their prime. efforts are 'still in technical lines, this new organization was to be devoted entirely to service, looking to the welfare of the nation and the engineering profession, and to service for the public in local and state affairs.

Jan 1, 1920

By N. Shiarella, Coleman D. Hunter, I. B. Browning

The price of crude oil in Kentucky did not change very much during 1935 until the latter part of the year, but more stabilized conditions and an increase in consumption of natural gas made the year a more profitable one than the year 1934. The production of crude oil in 1935 amounted to 5,175,054 bbl. as compared to 4,814,904 bbl. in 1934. This increase was due to two developments: (1) the application of new recovery methods to old fields, which, although in operation in the state for several years, had never before reached a point where the production obtained, while highly satisfactory where applied, was sufficient to influence the totals in the production figures; (2) the development of the Fordsville area in Ohio County, where shallow depths enabled the operators to complete the development of a large number of wells with a good flush production probably accounted for most of the increase. A map showing the location of oil and gas pools in Kentucky was published last year.' The fields of eastern Kentucky, producing from the Weir sand of the Waverly group of the Lower Mississippian series, in Johnson, Magoffin, Lawrence and Elliott counties, produced 826,001 bbl. of oil in 1935 as compared with 902,247 bbl. in the previous year. No new wells were drilled in this area during the year, except those for use as intake wells in repressuring. What has been done in the few small areas within these fields in the way of repressuring has produced results sufficient to a great extent to offset the natural decline of all the field. It is probable the drilling of new wells and construction of new plants will be such as to cause these fields to produce more in 1936 than was produced in the past year. This is based on the fact that the sand is highly favorable for repressuring and the results obtained show from 300 to 500 per cent increase in production. From the "Corniferous" pools, where production is from the Cornifer-ous limestone of Devonian age, in Lee, Powell, Estill, Wolfe, Morgan and

Jan 1, 1936