Search Documents

By C. J. Clayton, A. J. Haynes, D. A. Hickson, B. Thiele

The Meadowbank Gold Project, formerly owned by Cumberland Resources Ltd. and currently owned by Agnico Mines Ltd., is currently being developed approximately 70 km north of Baker Lake, Nunavut, in the eastern Canadian Arctic region. The Meadowbank Gold Project currently consists of a series of gold-bearing deposits within relatively close proximity to one another, which are planned to be mined primarily as a truck-and-shovel open pit operation using conventional gold milling and extraction. The mining plan indicates that approximately 20 million tonnes of ore will be mined over a mine life of eight to ten years. The operation will generate approximately 160 million tonnes of mine waste rock and about 20 million tonnes of tailings. The site is located in an area of continuous permafrost with mean annual average air temperature of -11°C and average annual precipitation in the range of 100 to 200 mm. Lakes cover a large portion of the site, including some of the ore deposits. The location of the site and the physical environment pose challenges to development. This paper presents some of the designs considered to effectively manage and utilize the waste products of mining at the project. Note that volumes, tonnages, construction concepts, and data presented in this paper are accurate for the time of writing and are subject to change and modification as the project progresses, additional modelling is carried out, and additional data are obtained.

Jan 1, 2007

By G. E. McElroy

Tae purpose of this paper is to present types of charts adapted to aid in the graphic solution of fan-performance problems of selection and operation, and to urge the adoption of similar charts by the National Association of Fan Manufacturers as standard forms for presenting fan-performance data. As matters now stand, it is difficult for the average engineer to solve such problems because a laree number of variables are involved, and performance data are not presented in a manner that permits their direct application to many problems encountered in practice. The performance of any centrifugal machine is determined not only by the machine itself but also by the fluid-flow system on which it operates. Actual performance of centrifugal fans is therefore e matter of the type, size, and speed of fan, on the one hand, and of the relation of pressure to quantity of flow, as determined by the physical condition of the airway system, on the other.

Jan 1, 1936

By Jane Li, Kevin Tom

"Research has shown that broken rock on conveyor transport systems can contribute upwards of 50% towards the overall heat load in underground mines. However, few studies have made significant efforts to predict the temperature distribution of the ore and air simultaneously, which can help implement heat management strategies. The present investigation explores a transient, analytical heat transfer model to track ore-pile temperature distributions, along conveyor systems in an example underground mine. Production rate, ambient conditions, ore pile thickness and belt velocity are adjusted to evaluate the effect on dry and wet bulb temperatures.INTRODUCTIONWith an ever increasing demand on Earth’s resources due to a multitude of factors like population growth and step changes in technology, pressure on the mining industry to bring out more ore with improved margins is a persistent challenge. Typically, high-volume producing mining methods (i.e., exceeding 5000 tons per day (tpd)) such as sublevel and block caving, room and pillar, and longwall shall utilize belt conveyors instead of trucks as the primary haulage method to surface to save on operational costs (de la Vergne, 2014). However, studies have shown that when such material transport systems are installed at mine depths with virgin rock temperatures (VRT) above 40oC, the heat dissipated by the conveyed ore can account for over 50% of the underground heat-load (Pareja, 2000; Bluhm, Jones, Moreby, & von Glehn, 2012; van den Berg, Moreby, & Kok, 2015).Unlike other types of heat sources encountered in underground mines, such as diesel machines, strata, electrical devices, and autocompression, heat transfer by conveyed broken rock is much more difficult to estimate. The seminal work of McPherson (1993) states that broken rock heat transfer is a function of its surface area, and the air’s psychrometric condition. It is additionally a function of the VRT, its specific heat, production rate, heat transfer coefficient and the residence time (Bossard, 1997; Ross, Tuck, Stokes, & Lowndes, 1997). Consequently, few studies have attempted to analytically quantify the significance of ore heat flow."

Jan 1, 2019

There have been no major field developments during 1935. Operations have proceeded normally on the company's three producing fields, Masjid-i-Sulaiman, Haft Kel and Naft-i-Shah. The refinery at Kermanshah was commissioned in September, 1935, with a rated throughput capacity of 75,000 tons a year of topped crude to meet local requirements. Crude production from the Masjid-i-Sulaiman and Haft Kel fields is tabulated below: Masjid-i-Sulaiman Field.—The flowing lives of wells have been extended by (I) a process of acid treatment, thereby reducing the bottom-hole pressure differentials, and (2) by reducing the back-pressure. Optimum producing conditions for individual wells have been determined as a result of an experimental study of the amount of available energy in the reservoir crude and of energy losses in flowing wells. The return of surplus products to the reservoir has continued to be a satisfactory economic operation and the crude throughput capacity of the topping plant has been increased. The viscosity of residue returned to the reservoir is reduced before injection by regassing at 35 lb. per sq. in. absorption pressure with surplus gas. The pressure in the gas dome is falling at the low rate of one pound per annum. Haft Kel Field.—The delimitation of the main structure has proceeded; the oil-bearing area so far proved being about 50 square miles.

Jan 1, 1936

There have been no major field developments during 1935. Operations have proceeded normally on the company's three producing fields, Masjid-i-Sulaiman, Haft Kel and Naft-i-Shah. The refinery at Kermanshah was commissioned in September, 1935, with a rated throughput capacity of 75,000 tons a year of topped crude to meet local requirements. Crude production from the Masjid-i-Sulaiman and Haft Kel fields is tabulated below: Masjid-i-Sulaiman Field.—The flowing lives of wells have been extended by (I) a process of acid treatment, thereby reducing the bottom-hole pressure differentials, and (2) by reducing the back-pressure. Optimum producing conditions for individual wells have been determined as a result of an experimental study of the amount of available energy in the reservoir crude and of energy losses in flowing wells. The return of surplus products to the reservoir has continued to be a satisfactory economic operation and the crude throughput capacity of the topping plant has been increased. The viscosity of residue returned to the reservoir is reduced before injection by regassing at 35 lb. per sq. in. absorption pressure with surplus gas. The pressure in the gas dome is falling at the low rate of one pound per annum. Haft Kel Field.—The delimitation of the main structure has proceeded; the oil-bearing area so far proved being about 50 square miles.

Jan 1, 1936

By Brian Daniels, James Farroni

"Draw rock (small rock that forms/falls when bolting the roof and/or rib) is the cause of numerous injuries annually. These injuries result in lost work hours and low morale. The report below explains how ""Mine Safe Draw Rock Shields"" (Pans) are used in an underground operation. This report will chronicle the application of these pans in a Southern West Virginia coal mine along with testing data that measures their effectiveness. Since the introduction of these pans in 2002 the amount of reportable accidents relating to draw rock has decreased by 80%. The report below reinforces that perimeter contact is critical to the performance of these pans. In addition the strength of these products at the perimeter will determine their effectiveness. The results of the testing data outlined in this paper, along with the physical records at the study mine, confirm that the use of pans has significantly reduced draw rock falls at this facility.BACKGROUNDSupplemental support is defined as ground control that is used in addition to required support in an underground mine. Some examples of supplemental support are:• Pans• Mesh/Geogrid• Mats• Half Headers• Boards• ChannelA typical roof condition that warrants the use of pans is when loose small rock is dislodged while bolting. If the top is very scaly (loose, thin rock) additional supplemental support can be used in conjunction with pans such as mesh or geogrid (See Figure 1). Pans will provide protection where used and approximately 12 in (250 mm) out from perimeter. This is achieved by contact with a surface which will put scale in tension up to 12 in (250 mm) from perimeter of pan.INTRODUCTIONThe ease of applying a roof support system is critical to effectively operating a deep mine. Figure 2 shows how a pan is installed in conjunction with a roof bolt and bearing plate. The Mine Safety and Health Administration (MSHA) requires that supplemental support cannot decrease the performance of required support. The goal of using all supplemental support is to provide additional safety for the miner which equates to increased productivity.The ability of skin control products to contact a surface is the single most critical characteristic (Figure 3 and Figure 4). If the material does not contact the surface it cannot be effective. Therefore, the flexibility, design and proper installation of the products are critical in determining their effectiveness. Figure 5 shows the proper installation of the roof pan.To reiterate, all skin control must be applied in conjunction with a roof bolt and ASTM approved bearing plate as shown in Figure 4."

Jan 1, 2010

By M. A. Vasina, I. A. Matveeva, E. A. Naumova, V. V. Doroshenko, N. A. Belov

"Using the calculated (Thermo-Calc software) and experimental methods (SEM, TEM, EMPA, DSC, XRD, etc.) the phase composition, structure and hardening of aluminium alloys of the Al-Ca-Zn-Mg system were studied in the following range: 2. 5%Mg, up to 10% Ca, and up to 14% Zn (wt%). Fragments of this quaternary phase diagram in the aluminium corner were constructed, including the liquidus surface, as well as some vertical sections. It was shown that the relatively large amount of zinc enters in the Ca-containing phase, which formula can be described as (Al,Zn)4Ca. An increase of Zn content leads to formation of Al4Ca primary crystals at lower concentrations of calcium. The eutectic (Al)+(Al,Zn)4Ca has a fine structure and aluminide particles are capable to spheroidization during the heat treatment at temperature 500 C. The maximal level of hardness observed on calcium containing alloys was higher than 200 HV, what gives the reason to expect good strength properties. With an example of an Al-9% Zn-2,5%Mg-3,5% Ca model experimental alloy based on the (Al)+(Al,Zn)4Ca eutectic, a principal possibility of manufacturing thin rolled sheets was demonstrated.INTRODUCTION Aluminum alloyed with calcium was first studied in 1970-80s by such authors as Piatti (1976), Moore (1978, 1980), Il'enko (1985), Swaminathan (1990), and Perez-Prado (1997) as superplastic materials. In particular, the alloy systems Al-Ca-Zn were studied (Il'enko, 1985, Swaminathan, 1990, Perez-Prado, 1997). For some time there was no new published works concerning the aluminum-calcium alloys. During the last years many works were published dedicated to the calcium alloying of magnesium alloys (Kim, 2011; Xu, 2011; Aljarrah, 2008; Bakhsheshi, 2014). This urged the authors (Belov, Naumova & Akopyan, 2016) to start studying cast and wrought aluminum-calcium alloys for construction (2008–2014). There is almost no information in the literature concerning triple and more complex diagrams of the aluminum-based system states with calcium and other elements. In recent work, parts of the state diagrams are plotted for the aluminum angle zone: Al-Ca-Mg-Sc (Belov, Naumova & Bazlova, 2016), Al-Ca-Ni-Sc (Belov, Naumova & Bazlova, 2017), Al-Ca-Si-Sc (Belov, Naumova & Akopyan, 2017) and others. Special attention was paid to the study of the system Al-Ca-Zn-Mg (Naumova, 2017). Based on this system creation of advanced extra-high tensile alloys is planned. Wrought extra-high tensile alloys series 7??? based on the system Al-Zn-Mg-Cu are well studied."

Jan 1, 2018

By Robert C. Freas, William H. Lane, David J. Krohn

Maysville, Kentucky, is the location of Dravo Lime company's new 9 070 mt(10,000 tons) per day limestone mine and 2 727 mt (3000 tons) per day calcination plant. This complex has been designed as a unit, and capitalizes on recent technological advances. Geologically the Dravo facility is.located on the eastern flank of the Cincinnati Arch, with the high calcium limestone being found at a depth of approximately 274 m (900 ft). A systems approach has been employed in designing and equipping the mine. This allows for maximum production while maintaining flexibility and versatility. All hydraulic drilling, large LHD equipment, and an extendable mine conveyor system are utilized in a five-part mining cycle. A modular concept modifies the room and pillar system to optimize ventilation. The limestone is calcined in three 5.18 x 61.87 m (17 x 203 ft) KVS rotary kilns with a design capacity of 909 mt (1000 tons) per day of lime per kiln. The kilns are coal fired and equipped with preheaters. Lime storage is provided by three 57 m (186 ft) high concrete silos with a combined capacity of 40 909 mt.

Jan 1, 1976

By W. L. Price

Recent publication of United States Bureau of Mines figures showed that the sand and gravel (3) industry is the largest single mining industry in the United States in term of yearly tonnage produced. The yearly production of over 500,000,000 tons per year now exceed bituminous coal production. This disclosure caught unawares many observers who have not been following closely the rapid-growth of this phase of mining. Along with this steady growth in production, the sand and gravel industry has gone through an accelerated and varied program of beneficiation in a period of the last ten years.

Jan 1, 1958

By Floyd C. Bossard

In underground mining operations, the over- riding issue has to be protection of worker health and safety. The employees underground, making a living in a dangerous occupation, know these are major issues. These men bargain their lives and health on the presumption that the operating management knows its business, and they, the underground employees, can pursue their occupation with the assurance that management has provided a safe and healthy ambient underground environment. When management assumes the mantle of protection of underground workers, it has to be positive that qualified engineers have designed the project, and that capable operating personnel are in charge and always available. Those persons with these responsibilities must be knowledgeable in the engineering and occupational health aspects of sine ventilation. The ultimate function of a mine ventilation system is to provide a comfortable, healthy and safe ambient environment for the underground workers. The attainment of these objectives has been complicated with the increased application of electrical equipment and diesel-powered mechanized mining equipment underground (discharging toxic diesel emissions); increased production rates with the attendant increased production of airborne dust; and mine development in increasingly hostile mineral formations containing combustible strata gases, radon gas emissions, along with high heat and humidity. In general, the modern mechanization of present mining operations has resulted in a sore complex set of problems for the engineer planning the underground ambient environment.

Jan 1, 1983

By A. D. Mutch

IT has long been known that there are wide variations in the thermo-electric potential of pyrite. In the last few years a study of this variation and other properties of pyrite was carried out at the University of Toronto by F. G. Smith on specimens of pyrite from many localities.1-3 As a result of these studies the pyrite geothermometer was developed by Professor Smith. The calibration of the pyrite geothermometer is based on the assumption that "crystals of any one electronically conducting mineral species deposited at a high temperature have a more positive thermo-electric potential than crystals deposited at a low temperature, and the thermo-electric potential varies continuously between any given limits of the temperature of deposition." The cause of the variation was postulated to be crystal discontinuities, such as lineage boundaries. As yet this postulated relationship has not been established as fact. On theoretical grounds it is indicated that the thermo-electric potential of pyrite or any other partial conductor is dependent upon a number of factors as well as the temperature of formation. For this and other reasons there is ground for doubt as to the validity of the relationship postulated above. To date a large number of readings have been made with the pyrite geothermometer which have been recorded in terms of the calibration of the instrument in degrees centigrade. So far most of the pyrite tested by this technique has been in association with gold ore. The values for the temperature of formation obtained in these tests appear to be reasonable and, in relation to geological problems, to vary in the right sense. Determinations on some specimens not in association with gold ore have given readings that appear to be much too high, taking into account the probable maximum temperature of the host rock. To sum up, although many determinations made with the. pyrite geothermometer appear to give reasonable values for the temperature of formation of the pyrite, there are at the same time other readings which seem anomalous. On the basis of an examination of available results of work with the pyrite geothermometer, two problems must be considered: 1-the validity of the calibration of the pyrite geothermometer; and 2-the nature of the distribution of the thermo-electric potentials of pyrite in relation to the specific problems that have been examined. In this paper the academic problem relating to the validity of the calibration of the pyrite geothermometer will not be discussed. Instead, the variations of thermo-electric potential of pyrite in association with gold veins will be discussed with regard to specific examinations. The first of these two examinations deals with the distribution of thermo-electric potentials of pyrite in association with a gold vein and was carried out in the McIntyre Porcupine Mine, Schumacher, Ont., in the summer of 1949 as part of a study with this technique. The second problem deals with variations of thermo-electric potential of pyrite in gold ore specimens from all over the world. The specimens used in this study were part of the private collection of Frank Ebbutt, geologist for Howe Sound Exploration Co. Results of Detailed and Reconnaissance Studies In discussion of the results of determinations made in these two studies the values of thermo-electric potential in millivolts will be used. It will be noted that in some of the diagrams the determinations are recorded in terms of pyrite geothermometer temperatures. Fig. 1 is a calibration chart relating, pyrite geothermometer temperatures and thermo-electric potentials. A full discussion of the technique is given in the original paper by F. G. Smith.' Briefly, the determinations are made by placing two stainless steel probes, one hot and the other cold, against the surface of the pyrite crystal being tested. The thermo-electric potential that is developed is read with a null-point potentiometer that is calibrated in what

Jan 1, 1952

By Graham W. Marks

The general positions of the absorption maxima of aqueous solutions of the violet and green isomers of chromic sulfate the visible spectral region have long been known, but, to the knowledge of the writer, no comprehensive studies have ever been made. To gain further knowledge concerning these inorganic complexes and to investigate the possibilities of developing an analytical method for determining the concentrations of the violet and green isomers in a mixture, a more complete investigation was made in the spectral range from 325 to 850 millimicrons.

Jan 1, 1951

By N. B. Gray, A. E. Guerra, D. E. Morton

"The formation of splash in pyrometallurgical operations that involve the injection of gases into a liquid has been the subject of a number of studies over the last few decades. Given the complexity of the phenomena, there have been some advances in understanding the microscale formation of splash but the ability to accurately predict the amount and character of the splash formed is still in its infancy. First, the macroscale mechanisms for splash formation is very varied. Second, the timescales for splash formation are very small, usually less than 100 milliseconds, making experiments elucidating the formation of splash difficult and costly. Work at the GKW CRC has shown that the microscale mechanism of splash formation is primarily is due to the Kelvin-Helmholtz instability. Substantial progress has been made in understanding the behaviour of large bubbles in effecting splash formation and a simple model has been developed to estimate the behaviour of splash formed from a top submerged lance. Direct numerical computation of splash formation using the GKMAC codes developed at the Centre has been successful in simulating the impact of liquid drops onto a liquid bath.IntroductionInjection of gases into melts is used in the metallurgical industry to promote mixing to ensure acceptable heat and mass transfer rates, conveying solids for alloying, provide efficient contact for gas-melt reactions, and as a reactant. High gas injection rates bring about the formation of splash and slop. Extensive splash formation leads to loss of valuable product, creation of safety hazards, formation of accretion on refractory lining and exhaust ducts, and increased load on dust removal equipment. Many operators and researchers have claimed that splash formation is the limiting factor in many gas injected processes. The problems listed above lead to loss of production and increased maintenance, adding to the cost of processing base metals. Over the last five years, the GKW CRC has been studying the formation of splash from a number of sources. They include the impingment of drops on liquids[ l·2.31, slopping of bath liquidI4.51, breakup of gas bubbles at the liquid-gas interfacel61, shearing of liquids by gases[7·81, and impact of packets of fluids on solidsl81. Theoretically, the extreme deformation of fluid shape and the influence of surface tension makes the simulation of flow resulting from only a drop impacting on a liquid surface a very challenging computational fluid dynamics problem. Recently, we have been successful in simulating the formation of the Rayleigh jet resulting from a drop impact showing the effect of drop Froude number on the shape of the Rayleigh jet."

Jan 1, 1996

By Susan M. Moore

Many challenges are faced by workers in lower-seam (42 inches or less) mines. The lower-seam heights confine mine workers to their knees as they perform their daily tasks such as installing roof bolts, delivering supplies, repairing belt, or cutting coal. Miners working in these lower seams often consider kneepads to be their only line of defense against knee injuries. However, healthy knees do not start and stop with kneepads. Other interventions such as changing postures, proper hygiene, and work station design may also be used to reduce mine workers? risks for developing knee injuries. Incorporating these and many other interventions into a mine worker?s ?way of life? is an important step to ensuring a long, healthy career and retirement. Keeping knees healthy is also a key aspect to reducing costs in low-seam mines as the industry battles rising health care costs, and training/recruitment of replacement workers is time-consuming and costly. Educating the workforce about the possible interventions to reduce knee injury risk is a primary objective for the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Laboratory (PRL). Therefore, NIOSH researchers, along with industry and academia, developed a training package to educate the mining community about some possible interventions beyond kneepads that may be used to help decrease knee injury rates. Increased awareness and simple changes are the first steps to reducing knee injuries.

May 1, 2008

By S. P. Narayan

The hot deformation behavior of Pure Mg and Mg-0.29Ce alloy were studied by isothermal hot compression tests in the temperature range of 250 - 500°C and strain rate range of 10-3 - 102 s-1 in a computer-controlled 50kN servo hydraulic universal testing machine (UTM). The results show that the flow stress of Mg pure and Mg-0.29Ce alloy increases with strain rate and decreases after a peak value, indicating dynamic recovery and recrystallization. Process efficiency was increased by nearly 10 to 12% by addition of Ce in Mg. Mg pure exhibits instability zones between 250-275°C at 10 ? 102 s-1 and 400¬500°C at 101 ? 102 s-1 temperatures and strain rates respectively, rest is the safe deformation zone. Wherein, Mg-0.29 Ce exhibits two low efficiency zones from 250 ? 300°C at 10-2? 10° s-1, 400 ? 500°C at 101 ? 102s-1 and high efficiency zone at 450 ? 500°C at 10-3? 10-1s-1. 4D process maps were generated for the above said alloys which illustrate contours of power dissipation and instability in the 3D space of strain rate, temperature and strain.

Jan 1, 2011

By R. M. Porter

PILLAR extraction at the Sullivan Mine bas been in progress for over twenty-five years and bas .involved progressively larger pillars. The largest pillar blasted to date exceeds one million tons and is described in this paper. This blast is believed to be one of the largest to take place entirely under-ground. The Sullivan Mine, owned by The Consolidated Mining and Smelting Company of Canada Limited, is located in the southeastern corner of British Columbia on the east flank of the Purcell range overlooking the twenty-mile wide Rocky Mountain Trench (Figure 1). The orebody is a bedded replacement deposit in argillites, varying in thickness up to 300 feet, but averaging about 80 feet. Above the 3900 Level, the dip varies from nearly horizontal to 40 degrees; be-low the 3900 Level it varies from 45 to 20 degrees (Figure 2). Pillar extraction follows a plan of retreating outward from caved areas. The size of each blast is determined by the effect which the removal of support

Jan 1, 1961

By Richard C. Ballance

Fly ash from four sources and in certain proportions was shown to assist chemical coagulation of turbid water and settling of chemically induced floc. Fly ash reduced the time required to form the first visible floc, promoted more uniform flocs about 2 mm in diameter, and increased the mean settling rate of floc particles. Also, the addition of fly ash produced denser sludges than those obtained with alum alone. Final turbidities were independent of fly ash particle size and carbon content. Optimum proportions of fly ash additive are given.

Jan 1, 1966

By J. B. Hess, R. L. Dietrich

IN the mechanical twinning of magnesium on the {1012} planes the crystallographic deformation is such that, in the direction of the hexagonal axis [0001], twinning is possible only under tension stress, while in the directions perpendicular to the hexagonal axis, twinning is possible only under applied compression. Thus in extruded magnesium and magnesium alloys where the extruded textures are best described as either [1010] or [ 1120] fibers,1 the basal planes are all nearly parallel to the extrusion axis and such material is susceptible to {1012 } twinning by compression in the direction of the extrusion axis. In order to explain the results of cyclic stressing in alternate tension and compression upon the tangent elastic modulus in such material, Dorn and Thomsen2 have postulated that, following twinning under applied compression, a retwinning or untwinning occurs as a result of residual microtensile stresses immediately upon removal of the applied compressive force. Recently, Carapella and Shaw3,4 have used this supposition of untwinning in magnesium in discussing their results on indentation hardness and on cold drawing of MI sheet. In trying to confirm this hypothesis by suitable direct experiments, the authors have been unsuccessful in detecting any evidence whatsoever that untwinning follows the release of applied compression and are forced to conclude that this hypothesis is improbable or, at least, that the quantity of material involved is small. For the experiments, small cylindrical specimens 0.040-in. diam. X 0.120- to 0.140-in. long were etched from 0.0625-in. extruded rod. The ends of the specimens were accurately faced off parallel in a jeweler's lathe. The compression jig was simply an ordinary set of micrometer calipers with an anvil interposed between the spindle and the specimen. The anvil was free to move axially but restrained from rotating so that the rotation of the spindle would not introduce a twisting stress on the specimen. With this arrangement the compressive strains could be estimated to 0.0001 in. and X ray pinhole photographs could be taken with or without load as required. Fig 1 is the pattern of an uncompressed specimen of AZ31 alloy, showing the approximate [1010] extrusion fiber. The X ray beam is normal to the extrusion axis; in this position it is particularly sensitive in detecting twinning if one directs his attention to the diffraction ring from the basal plane. Since twinning on {1012} planes produced an 86° reorientation of the crystal lattice, the original basal reflections occur at the 3 and 9 o'clock positions while the (0002) reflections from any twinned material will occur at the 6 and 12 o'clock positions. Fig 2 shows the same specimen compressed 3.0 pct, photographed while still under load. This strain has been just enough to produce a detectible amount of twinning and the sensitivity is roughly indicated by the fact that no alterations were produced in the intensities or maxima of the other diffraction rings. A strain of

Jan 1, 1948

By Donald A. Bruce

Pregrouting is an extremely important part of many rock tunneling projects. However, poor and unsatisfactory performances have been frequently recorded often with very severe consequences, technically and financially. This paper, based on personal knowledge of several relevant case histories, provides recommendations with respect to specification drafting, drilling, water pressure testing, and grouting methodologies, and cementitious grout mix design principles. Even given that the logistical challenges facing tunnel pregrouting from underground will prevent all the sophistication and innovations of contemporary dam foundation grouting being practically implemented, there is still opportunity and need to change “traditional” approaches.

Jan 1, 2005

By Albert J. Phillips

FOR the most part, recent changes in nonferrous physical metallurgy have been gradual and of a transition nature rather than abrupt modifications of existing methods. Development of new alloys containing vital constituents in what formerly would have been considered minute amounts has necessitated more precise control of metallurgical procedure than ever before. Realization of the remarkable effects of minute amounts of specific foreign elements in many alloys has brought about a revolutionary control in the selection of even the most commonplace raw materials. In addition, recognition of the widespread occurrence of precipitation hardness in metal systems, and the utilization of many of these, has emphasized not only the need for precise temperature control but also the necessity for considering the time factor in its effect upon properties in the treatment of most metals. These needs have caused the development and widespread installation of equipment that permits precision of control undreamed of a generation ago.

Jan 1, 1935